MIB Viewer

A3COM-HUAWEI-DOT11-WLANEXT-MIB

22 objects
This MIB provides more information for WLAN network. GLOSSARY IEEE 802.11 Standard to encourage interoperability among wireless networking equipment. IEEE 802.11e Standard to define the MAC procedures to support LAN applications with Quality of Service (QoS) requirements, including the transport of voice, audio and video over IEEE 802.11 wireless LANs. Access point (AP) Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network. Access control (AC) To control and manage multi-APs, it will bridge wireless and wired network. Radio The chip set to receive and send wireless signal. Fat AP Applied in the home, SOHO and so on, and it could independently work without help from AC. Fit AP Applied in the enterprise environment, it will work under the control and management from AC. Control And Provisioning of Wireless Access Points Protocol The short name of protocol is CAPWAP. AC will control and manage AP by CAPWAP tunnel protocol defined by IETF. Also, a data tunnel will be set up between AC and AP. Basic Service Set The IEEE 802.11 BSS of an AP comprises of the stations directly associating with the AP. It will be identified by BSSID.
OIDNameAccessStatusDescription
1.3.6.1.4.1.43.45.1.10.2.75.7Identityh3cDot11WLANEXTThis MIB provides more information for WLAN network. GLOSSARY IEEE 802.11 Standard to encourage interoperability among wireless networking equipment. IEEE 802.…
1.3.6.1.4.1.43.45.1.10.2.75.7.1Nodeh3cDot11RFGroup
1.3.6.1.4.1.43.45.1.10.2.75.7.1.1Tableh3cDot11RFSignalStatisTablenot-accessiblecurrentThe table will describe statistic information of signal strength for AP radio.
1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1Rowh3cDot11RFSignalStatisEntrynot-accessiblecurrentEach entry contains the signal of each signal strength information of a specific AP.
1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1.1Columnh3cDot11RFAPIDnot-accessiblecurrentTo identify each AP, and AP is running status.
1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1.2Columnh3cDot11RFRadioIDnot-accessiblecurrentRepresents each radio.
1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1.3Columnh3cDot11RFSignalStatisIntervread-onlycurrentRepresents the interval of statistic.
1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1.4Columnh3cDot11RFAverageSignalStrengthread-onlycurrentRepresents the average value of signal strength for stations on a specific radio.
1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1.5Columnh3cDot11RFMaxSignalStrengthread-onlycurrentRepresents the maximum value of signal strength for stations on a specific radio.
1.3.6.1.4.1.43.45.1.10.2.75.7.1.1.1.6Columnh3cDot11RFMinSignalStrengthread-onlycurrentRepresents the minimum value of signal strength for stations on a specific radio.
1.3.6.1.4.1.43.45.1.10.2.75.7.2Nodeh3cDot11QosGroup
1.3.6.1.4.1.43.45.1.10.2.75.7.2.1Tableh3cDot11QosStatisTablenot-accessiblecurrentThe table defines the attributes for the Qos feature of radio.
1.3.6.1.4.1.43.45.1.10.2.75.7.2.1.1Rowh3cDot11QosStatisEntrynot-accessiblecurrentEach entry contains information of the Qos attribute of each radio.
1.3.6.1.4.1.43.45.1.10.2.75.7.2.1.1.1Columnh3cDot11QosAPIDnot-accessiblecurrentTo uniquely identify a AP in running status.
1.3.6.1.4.1.43.45.1.10.2.75.7.2.1.1.2Columnh3cDot11QosRadioIDnot-accessiblecurrentRepresents each radio.
1.3.6.1.4.1.43.45.1.10.2.75.7.2.1.1.3Columnh3cDot11QosAverageQueLenread-onlycurrentThe average frame numbers to be sent out in the queue.
1.3.6.1.4.1.43.45.1.10.2.75.7.2.1.1.4Columnh3cDot11QosDropFrameRatioread-onlycurrentThe ratio of dropped frames in a minute because of full queue.
1.3.6.1.4.1.43.45.1.10.2.75.7.2.1.1.5Columnh3cDot11QosAverageDataRateread-onlycurrentThe average transmit data rate of radio.
1.3.6.1.4.1.43.45.1.10.2.75.7.2.2Tableh3cDot11QosAcStatisTablenot-accessiblecurrentThe table defines the parameters for Qos access category.
1.3.6.1.4.1.43.45.1.10.2.75.7.2.2.1Rowh3cDot11QosAcStatisEntrynot-accessiblecurrentEach entry contains information of each Qos access category.
1.3.6.1.4.1.43.45.1.10.2.75.7.2.2.1.1Columnh3cDot11QosAcTypenot-accessiblecurrentThe access category type.
1.3.6.1.4.1.43.45.1.10.2.75.7.2.2.1.2Columnh3cDot11AcDropFrameCntread-onlycurrentThe number of dropped frames in a minute for one specific access category because of full queue.