A3Com-IPX-r5-MIB
99 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | enterprises |
| RFC1213-MIB | DisplayString PhysAddress |
| RFC1286-MIB MISSING | MacAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.43 | Nodea3Com | |||
| 1.3.6.1.4.1.43.2 | NodebrouterMIB | |||
| 1.3.6.1.4.1.43.2.7 | Nodea3ComIPX | |||
| 1.3.6.1.4.1.43.2.7.1 | Nodea3ipxGeneral | |||
| 1.3.6.1.4.1.43.2.7.1.1 | Scalara3ipxRouteControl | read-write | deprecated | If this object is set to enabled(1), then IPX routing is enabled. If this object is set to disabled(2), then IPX routing is disabled. Note, if this is disabled… |
| 1.3.6.1.4.1.43.2.7.1.2 | Scalara3ipxWanBcastControl | read-write | deprecated | If this object is enabled(1), then the IPX router makes copies of all received WAN broadcast packets and forwards them to all ports other than the one on which… |
| 1.3.6.1.4.1.43.2.7.1.3 | Scalara3ipxUpdateTime | read-write | deprecated | This parameter specifies how often the router sends both RIP and SAP regular updates to exhange routing and service information. This parameter is defined in u… |
| 1.3.6.1.4.1.43.2.7.1.4 | Scalara3ipxFlushRipSap | read-write | mandatory | This object is used to remove dynamic routing and or sap entries quickly and efficiently. Setting this object to rip (2) causes all dynamically entered routes … |
| 1.3.6.1.4.1.43.2.7.1.5 | Scalara3ipxInternalNet | read-write | mandatory | This object represents the router's internal network number. This is used during IPX WAN negotiation and is the basis on which the MASTER/SLAVE selection is ma… |
| 1.3.6.1.4.1.43.2.7.1.6 | Scalara3ipxRouterName | read-write | mandatory | This object specifies the router's symbolic name and is used during IPX WAN negotiations to build RIP/SAP Information Request/Response packets. |
| 1.3.6.1.4.1.43.2.7.1.7 | Nodea3ipxControl | |||
| 1.3.6.1.4.1.43.2.7.1.7.1 | Tablea3ipxControlTable | not-accessible | mandatory | A list of port-specific IPX control parmeters. This table is used currently to control ipx routing, WAN broadcasts, and WAN checksums. |
| 1.3.6.1.4.1.43.2.7.1.7.1.1 | Rowa3ipxControlEntry | not-accessible | mandatory | Each entry in this table applies control over a seperate port. |
| 1.3.6.1.4.1.43.2.7.1.7.1.1.1 | Columna3ipxControlPort | read-only | mandatory | The IPX port to which this entry applies. |
| 1.3.6.1.4.1.43.2.7.1.7.1.1.2 | Columna3ipxControlRoute | read-write | mandatory | If this object is set to enabled(1), then IPX routing is enabled. If this object is set to disabled(2), then IPX routing is disabled. Note, if this is disabled… |
| 1.3.6.1.4.1.43.2.7.1.7.1.1.3 | Columna3ipxControlWanBcast | read-write | mandatory | If this object is enabled(1), then the IPX router makes copies of all received WAN broadcast packets and forwards them to all ports other than the one on which… |
| 1.3.6.1.4.1.43.2.7.1.7.1.1.4 | Columna3ipxControlChecksum | read-write | mandatory | If this object is set to enabled(1), Checksum will be generated and checked on IPX packet over WAN. |
| 1.3.6.1.4.1.43.2.7.1.7.1.1.5 | Columna3ipxControlWanOpt | read-write | mandatory | This object is used to enable or disable the IPX WAN feature on a specific port. IPX WAN is the protocol Novell IPX uses to exchange necessary router to router… |
| 1.3.6.1.4.1.43.2.7.1.8 | Scalara3ipxRipHoldTimeFactor | read-write | mandatory | This parameter specifies a factor that RIP uses to generate a hold time. A holdtime is generated by HoldTimeFactor * UpdateTime. A entry in RIP will be aged ou… |
| 1.3.6.1.4.1.43.2.7.1.9 | Scalara3ipxSapHoldTimeFactor | read-write | mandatory | This parameter specifies a factor that SAP uses to generate a hold time. A holdtime is generated by HoldTimeFactor * UpdateTime. A entry in SAP will be aged ou… |
| 1.3.6.1.4.1.43.2.7.2 | Tablea3ipxRipControlTable | not-accessible | mandatory | A list of RIP Control parameter entries |
| 1.3.6.1.4.1.43.2.7.2.1 | Rowa3ipxRipControlEntry | not-accessible | mandatory | A list of parameters that determin how IPX updates its routing table. |
| 1.3.6.1.4.1.43.2.7.2.1.1 | Columna3ipxRipControlPort | read-only | mandatory | The IPX port to which this entry applies. |
| 1.3.6.1.4.1.43.2.7.2.1.2 | Columna3ipxRipControlSwitch | read-write | deprecated | If this object is set to enabled(1), IPX RIP exchanges RIP information with its neighbors and maintains the routing table dynamically. If this object is set to… |
| 1.3.6.1.4.1.43.2.7.2.1.3 | Columna3ipxRipControlTrigger | read-write | mandatory | If this object is set to enabled(1), triggered responses are sent when the network topology changes, allowing the network to calculate potentially better route… |
| 1.3.6.1.4.1.43.2.7.2.1.4 | Columna3ipxRipControlPoison | read-write | mandatory | If this object is set to enabled(1), Split Horizon with Poison Reverse is performed. If this object is set to disabled(2), the router omits routes learned from… |
| 1.3.6.1.4.1.43.2.7.2.1.5 | Columna3ipxRipControlMapOpt | read-write | mandatory | X.25 addresses and Frame Relay DLCIs can be mapped in two different ways: by using IPX network numbers as previously implemented (OldNbrMap) or by using the Et… |
| 1.3.6.1.4.1.43.2.7.2.1.6 | Columna3ipxRipControlWanOpt | read-write | deprecated | This object is used to enable or disable the IPX WAN feature on a specific port. IPX WAN is the protocol Novell IPX uses to exchange necessary router to router… |
| 1.3.6.1.4.1.43.2.7.2.1.7 | Columna3ipxRipControlPerRip | read-write | mandatory | This object is used to specify how this router generates IPX RIP updates. If this object is set to periodicRip(1), the router will generate RIP updates periodi… |
| 1.3.6.1.4.1.43.2.7.2.1.8 | Columna3ipxRipControlPerSap | read-write | mandatory | This object is used to specify how this router generates IPX SAP updates. If this object is set to periodicSap(1), the router will generate SAP updates periodi… |
| 1.3.6.1.4.1.43.2.7.2.1.9 | Columna3ipxRipControlTalk | read-write | deprecated | This object controls the transmission of IPX RIP updates on this port. If enabled, IPX RIP updates are sent. If disabled, they are not sent. |
| 1.3.6.1.4.1.43.2.7.2.1.10 | Columna3ipxRipControlListen | read-write | deprecated | This object determines if IPX RIP updates are accepted over this port. If this object is enabled(1), then the IPX router listens to the incoming RIP updates. I… |
| 1.3.6.1.4.1.43.2.7.2.1.11 | Columna3ipxSapControlTalk | read-write | deprecated | This object controls the transmission of IPX SAP updates on this port. If enabled, IPX SAP updates are sent. If disabled, they are not sent. |
| 1.3.6.1.4.1.43.2.7.2.1.12 | Columna3ipxSapControlListen | read-write | deprecated | This object determines if IPX SAP updates are accepted over this port. If this object is enabled(1), then the IPX router listens to the incoming SAP updates. I… |
| 1.3.6.1.4.1.43.2.7.2.1.13 | Columna3ipxRipCtl | read-write | mandatory | |
| 1.3.6.1.4.1.43.2.7.2.1.14 | Columna3ipxSapCtl | read-write | mandatory | |
| 1.3.6.1.4.1.43.2.7.3 | Tablea3ipxWaAddrTable | not-accessible | mandatory | A list of IPX entities reachable across a wide area network. |
| 1.3.6.1.4.1.43.2.7.3.1 | Rowa3ipxWaAddrEntry | not-accessible | mandatory | Each entry contains the WAN Address of an IPX entity. Each entry also contains the IPX port over which the entity can be reached. |
| 1.3.6.1.4.1.43.2.7.3.1.1 | Columna3ipxWaAddrEthAddress | read-only | mandatory | The Ethernet address (IPX Node ID) of a remote IPX entity. |
| 1.3.6.1.4.1.43.2.7.3.1.2 | Columna3ipxWaAddrPort | read-write | mandatory | The IPX port through which the IPX entity identified by a3ipxWaAddrEthAddress can be reached. |
| 1.3.6.1.4.1.43.2.7.3.1.3 | Columna3ipxWaAddrDLType | read-write | mandatory | The type of address that is returned by a3ipxWaAddrDLAddress. |
| 1.3.6.1.4.1.43.2.7.3.1.4 | Columna3ipxWaAddrDLAddress | read-write | mandatory | The WAN address that is used to reach the IPX entity corresponding to this table entry. |
| 1.3.6.1.4.1.43.2.7.3.1.5 | Columna3ipxWaAddrStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB. |
| 1.3.6.1.4.1.43.2.7.4 | Tablea3ipxAttachedNetTable | not-accessible | mandatory | A list of the IPX Network Numbers attached to an IPX port. |
| 1.3.6.1.4.1.43.2.7.4.1 | Rowa3ipxAttachedNetEntry | not-accessible | mandatory | Each entry specifies an IPX network number, assigns it to a port, and specifies the header format to be used when sending IPX packets to that network. On Ether… |
| 1.3.6.1.4.1.43.2.7.4.1.1 | Columna3ipxAttachedNetNumber | read-only | mandatory | The IPX Network Number associated with this table entry. |
| 1.3.6.1.4.1.43.2.7.4.1.2 | Columna3ipxAttachedNetPort | read-write | mandatory | The port to which the IPX Network Number is assigned. |
| 1.3.6.1.4.1.43.2.7.4.1.3 | Columna3ipxAttachedNetFormat | read-write | mandatory | The format of the header used on packets sent to the IPX Network Number associated with this table entry. This object can be set to 1, 2, 3, or 4 when adding a… |
| 1.3.6.1.4.1.43.2.7.4.1.4 | Columna3ipxAttachedNetType | read-write | mandatory | When more than one IPX Network Number is assigned to a port, one must be labeled the primary number and the rest secondary. |
| 1.3.6.1.4.1.43.2.7.4.1.5 | Columna3ipxAttachedNetOperState | read-only | mandatory | This identifies the current operational state of an attached IPX network. |
| 1.3.6.1.4.1.43.2.7.4.1.6 | Columna3ipxAttachedNetStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB. |
| 1.3.6.1.4.1.43.2.7.5 | Tablea3ipxRouteTable | not-accessible | mandatory | A list of IPX routes |
| 1.3.6.1.4.1.43.2.7.5.1 | Rowa3ipxRouteEntry | not-accessible | mandatory | Each entry specifies an IPX route. The destination of the route is specified by a3ipxRouteDestNet. The next hop of the route is specified by a3ipxRouteAttached… |
| 1.3.6.1.4.1.43.2.7.5.1.1 | Columna3ipxRouteDestNet | read-only | mandatory | The IPX network number of the destination network. The value 0xfffffffe is used to represent the default route. |
| 1.3.6.1.4.1.43.2.7.5.1.2 | Columna3ipxRouteAttachedNet | read-write | mandatory | The network number of the directly connected network through which the router can reach the destination network. |
| 1.3.6.1.4.1.43.2.7.5.1.3 | Columna3ipxRouteDLType | read-only | mandatory | The type of network to which the closest router is attached. This value is determined by the value of a3ipxRouteAttachedNet. |
| 1.3.6.1.4.1.43.2.7.5.1.4 | Columna3ipxRouteDLAddress | read-write | mandatory | The Data Link address of the next hop router through which the IPX network can be reached. The type of address is determined by the value of a3ipxRouteDLType. |
| 1.3.6.1.4.1.43.2.7.5.1.5 | Columna3ipxRouteHops | read-write | mandatory | The number of gateways that a packet has to pass through before reaching the destination network. The maximum number of hops is 15. |
| 1.3.6.1.4.1.43.2.7.5.1.6 | Columna3ipxRouteType | read-only | mandatory | The IPX Router allows up to two routes (ie, two separate next hop routers) to a specific destination network, only one of which will be the primary route. The … |
| 1.3.6.1.4.1.43.2.7.5.1.7 | Columna3ipxRouteProto | read-only | mandatory | This object specifies how the entry was made. |
| 1.3.6.1.4.1.43.2.7.5.1.8 | Columna3ipxRouteDelay | read-write | mandatory | The delay associated with the route. |
| 1.3.6.1.4.1.43.2.7.5.1.9 | Columna3ipxRouteStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB. Note, only statically learned rou… |
| 1.3.6.1.4.1.43.2.7.6 | Tablea3ipxServerTable | not-accessible | mandatory | A list of servers reachable via this router |
| 1.3.6.1.4.1.43.2.7.6.1 | Rowa3ipxServerEntry | not-accessible | mandatory | Each entry specifies the reachability of a server. The server name is specified by a3ipxServerName. The service is fully specified by a3ipxServerName, and a3ip… |
| 1.3.6.1.4.1.43.2.7.6.1.1 | Columna3ipxServerName | read-only | mandatory | The name of the server. |
| 1.3.6.1.4.1.43.2.7.6.1.2 | Columna3ipxServerType | read-only | mandatory | The type of service available on the server. |
| 1.3.6.1.4.1.43.2.7.6.1.3 | Columna3ipxServerNet | read-write | mandatory | The IPX network number on which the server resides. |
| 1.3.6.1.4.1.43.2.7.6.1.4 | Columna3ipxServerDLAddress | read-write | mandatory | The Mac address of the server. |
| 1.3.6.1.4.1.43.2.7.6.1.5 | Columna3ipxServerSocket | read-write | mandatory | The socket number of the service. |
| 1.3.6.1.4.1.43.2.7.6.1.6 | Columna3ipxServerProto | read-only | mandatory | This object identifies how the entry was made. If the entry was learned via the Service Advertisement Protocol, this object will have the value sap(3). If the … |
| 1.3.6.1.4.1.43.2.7.6.1.7 | Columna3ipxServerStatus | read-write | mandatory | This table currently does not allow entries to be added. This object is used to delete entries from this table. See the notes describing RowStatus at the begin… |
| 1.3.6.1.4.1.43.2.7.7 | Tablea3ipxX25configTable | not-accessible | mandatory | A list of IPX X25 configuration entries. |
| 1.3.6.1.4.1.43.2.7.7.1 | Rowa3ipxX25configEntry | not-accessible | mandatory | Each entry specifies a list of X25 configuration parameters applying to an IPX port. |
| 1.3.6.1.4.1.43.2.7.7.1.1 | Columna3ipxX25configPort | read-only | mandatory | The port number to which this table entry applies. |
| 1.3.6.1.4.1.43.2.7.7.1.2 | Columna3ipxX25configPID | read-write | mandatory | The protocol ID that is included in all outgoing IPX packets sent over the X25 port associated with this table entry. |
| 1.3.6.1.4.1.43.2.7.7.1.3 | Columna3ipxX25configQueueSize | read-write | deprecated | The maximum number of packets that can be queued for a specific DTE address when the virtual circuit or the X25 port is congested. NOTE: this object is no long… |
| 1.3.6.1.4.1.43.2.7.7.1.4 | Columna3ipxX25configVClimit | read-write | deprecated | The maximum number of virtual circuits that can be established concurrently for IPX routing. NOTE: this object is no longer supported by NETBuilders running sw… |
| 1.3.6.1.4.1.43.2.7.7.1.5 | Columna3ipxX25configVCtimer | read-write | deprecated | The maximum amount of time, in minutes, that can elapse when there is no activity on the X25 virtual circuit before it is cleared. This applies to the first vi… |
| 1.3.6.1.4.1.43.2.7.7.1.6 | Columna3ipxX25configProfId | read-write | mandatory | To specify an X.25 profile that will be used when the virtual circuit is set-up to carry the IPX traffic. default (0) indicates that no x25 profile is specifie… |
| 1.3.6.1.4.1.43.2.7.8 | Tablea3ipxSmdsGroupAddressTable | not-accessible | mandatory | A list of SMDS Group Addresses assigned to IPX Ports. |
| 1.3.6.1.4.1.43.2.7.8.1 | Rowa3ipxSmdsGroupAddressEntry | not-accessible | mandatory | Each entry specifies the SMDS Group Address assigned to an IPX port. |
| 1.3.6.1.4.1.43.2.7.8.1.1 | Columna3ipxSmdsGaIpxPort | read-only | mandatory | This identifies an IPX port to which the SMDS Group Address identified by the corresponding instance of a3ipxSmdsGaAddress is associated. |
| 1.3.6.1.4.1.43.2.7.8.1.2 | Columna3ipxSmdsGaAddress | read-write | mandatory | This identifies an SMDS Group address that is used as the IPX multicast address on the specified SMDS port. If this object has a value of all zeros, then no SM… |
| 1.3.6.1.4.1.43.2.7.9 | Tablea3ipxPreferredSvrTable | not-accessible | mandatory | A list of those IPX servers that are included in responses to 'Get Nearest Server' requests. Separate lists are kept for each port. When a request is receive o… |
| 1.3.6.1.4.1.43.2.7.9.1 | Rowa3ipxPreferredSvrEntry | not-accessible | mandatory | Each entry specifies an IPX server that will be offered when a 'Get Nearest Server' request in received over a particular port. |
| 1.3.6.1.4.1.43.2.7.9.1.1 | Columna3ipxPrefSvrPort | read-only | mandatory | This identifies an IPX port to which the IPX server identified by the corresponding instance of a3ipxPrefSvrName is associated. |
| 1.3.6.1.4.1.43.2.7.9.1.2 | Columna3ipxPrefSvrName | read-only | mandatory | This identifies an IPX server that is offered in response to 'Get Nearest Server' requests received over the port identified by a3ipxPrefSvrPort. If there exis… |
| 1.3.6.1.4.1.43.2.7.9.1.3 | Columna3ipxPrefSvrStatus | read-write | mandatory | This object is used to add and remove entries from this table. See the definition of RowStatus at the beginning of this mib module for details. |
| 1.3.6.1.4.1.43.2.7.10 | Tablea3ipxPortconfigTable | not-accessible | mandatory | A list of port-specific parmeters. |
| 1.3.6.1.4.1.43.2.7.10.1 | Rowa3ipxPortconfigEntry | not-accessible | mandatory | Each entry in this table applies the paramater over a seperate port. |
| 1.3.6.1.4.1.43.2.7.10.1.1 | Columna3ipxPortconfigPort | read-only | mandatory | The port number to which this table entry applies. |
| 1.3.6.1.4.1.43.2.7.10.1.2 | Columna3ipxRipUpdateTime | read-write | mandatory | This parameter specifies how often the router sends RIP regular updates to exhange routing information. This parameter is defined in units of seconds. |
| 1.3.6.1.4.1.43.2.7.10.1.3 | Columna3ipxSapUpdateTime | read-write | mandatory | This parameter specifies how often the router sends Sap regular updates to exhange and service information. This parameter is defined in units of seconds. |
| 1.3.6.1.4.1.43.2.7.10.1.4 | Columna3ipxDefMetricHops | read-write | mandatory | This parameter specifies the hop value placed in NRIP advertisements of the default route. If this object has the value 0, the default route is not advertised. |
| 1.3.6.1.4.1.43.2.7.10.1.5 | Columna3ipxDefMetricTicks | read-write | mandatory | This parameter specifies the number of ticks placed in NLSP advertisements of the default route. |
| 1.3.6.1.4.1.43.2.7.11 | Tablea3ipxSpoofCtlTable | not-accessible | mandatory | A table of spoof controls for all the ports. Each row, represented by a3ipxSpoofCtlEntry, contains the various spoof controls that are applicable to a port. |
| 1.3.6.1.4.1.43.2.7.11.1 | Rowa3ipxSpoofCtlEntry | not-accessible | mandatory | Each entry represents the various spoof controls applicable to a port. |
| 1.3.6.1.4.1.43.2.7.11.1.1 | Columna3ipxSpoofCtlPort | read-only | mandatory | Specifies the port number, used as an index to a row entry in the table. |
| 1.3.6.1.4.1.43.2.7.11.1.2 | Columna3ipxSpoofCtlWatchdog | read-write | mandatory | Used to enable(1) or disable(2) the Spoofing of Watchdog packets. |