A3Com-Dvmrp-r1-MIB
98 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | enterprises IpAddress |
| RFC1213-MIB | PhysAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.43 | Nodea3Com | |||
| 1.3.6.1.4.1.43.2 | NodebrouterMIB | |||
| 1.3.6.1.4.1.43.2.28 | Nodea3ComDVMRP | |||
| 1.3.6.1.4.1.43.2.28.1 | Nodea3ComDvmrpSConfig | |||
| 1.3.6.1.4.1.43.2.28.1.1 | Scalara3ComDvmrpCacheTime | read-write | mandatory | This object specifies the time in seconds a (source, group) entry is kept in the forwarding table. The entry can be kept within 5 minutes to 1 day. |
| 1.3.6.1.4.1.43.2.28.1.2 | Scalara3ComDvmrpPrune | read-write | mandatory | If this object is set to enabled(1), then prune is on when running multicast routing with DVMRP protocol. If is is set to disabled(2), then prune is turned off. |
| 1.3.6.1.4.1.43.2.28.1.3 | Scalara3ComDvmrpUpdateTime | read-write | mandatory | This object specifies the time interval in seconds that Route Report containing complete routing table is sent. It also derives Route Expiration time which is … |
| 1.3.6.1.4.1.43.2.28.1.4 | Scalara3ComDvmrpMospfPolicy | read-write | mandatory | If this object is set to mospf(1), the system will import the route source from MOSPF domain into DVMRP. The route source is controlled by the object a3ComDvmr… |
| 1.3.6.1.4.1.43.2.28.1.5 | Scalara3ComDvmrpDestGroupPolicy | read-write | mandatory | This object is used to control data packets forward to MOSPF domain. If this object is set to destGroup(1), data packet will be checked with object a3ComDvmrpD… |
| 1.3.6.1.4.1.43.2.28.2 | Nodea3ComDvmrpCConfig | |||
| 1.3.6.1.4.1.43.2.28.2.1 | Tablea3ComDvmrpPortTable | not-accessible | mandatory | This table contains entries of parameters associated with every port or tunnel. |
| 1.3.6.1.4.1.43.2.28.2.1.1 | Rowa3ComDvmrpPortEntry | not-accessible | mandatory | Each entry contains information for a spcified port or tunnel. |
| 1.3.6.1.4.1.43.2.28.2.1.1.1 | Columna3ComDvmrpPortIndex | read-only | mandatory | The port number or tunnel ID of which this entry applies. The tunnel ID starts with 1025 and end with 1056, i.e. total tunnel number is limited to 32. |
| 1.3.6.1.4.1.43.2.28.2.1.1.2 | Columna3ComDvmrpPortControl | read-write | mandatory | This object allows the multicast routing to run with DVMRP or not. |
| 1.3.6.1.4.1.43.2.28.2.1.1.3 | Columna3ComDvmrpPortMetric | read-write | mandatory | This object specifies the cost to the given port or tunnel. A value of 32 is considered 'infinity'. |
| 1.3.6.1.4.1.43.2.28.2.1.1.4 | Columna3ComDvmrpPortRateLimit | read-write | mandatory | This object specifies the bandwidth in Kbits/second that will be allocated for the multicast datagrams traffic. If set the value to 0 then the full bandwidth o… |
| 1.3.6.1.4.1.43.2.28.2.1.1.5 | Columna3ComDvmrpPortAggregateCtrl | read-write | mandatory | This object controls the way to advertise routes. |
| 1.3.6.1.4.1.43.2.28.2.2 | Tablea3ComDvmrpBoundaryAddrTable | not-accessible | mandatory | This table contains multicast addresses to be scoped for each port or tunnel. |
| 1.3.6.1.4.1.43.2.28.2.2.1 | Rowa3ComDvmrpBoundaryAddrEntry | not-accessible | mandatory | Each entry contains a single or a range of multicast addresses to be scoped over a specific port or tunnel. |
| 1.3.6.1.4.1.43.2.28.2.2.1.1 | Columna3ComDvmrpBoundaryAddrPort | read-only | mandatory | The port or tunnel number to which this entry applies. |
| 1.3.6.1.4.1.43.2.28.2.2.1.2 | Columna3ComDvmrpBoundaryAddrIpAddr | read-only | mandatory | This allows you to configure a single or a set of multicast addresses to be scoped that they do not get forwarded beyond a boundary router. |
| 1.3.6.1.4.1.43.2.28.2.2.1.3 | Columna3ComDvmrpBoundaryAddrMask | read-write | mandatory | This is the subnet mask associated with a3ComDvmrpBoundaryIpAddr of this entry. If this is not specified, the value 255.255.255.255 is used. |
| 1.3.6.1.4.1.43.2.28.2.2.1.4 | Columna3ComDvmrpBoundaryAddrStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the definition of RowStatus for detail. |
| 1.3.6.1.4.1.43.2.28.2.3 | Tablea3ComDvmrpMospfTable | not-accessible | mandatory | This table contains a list of source subnet in MOSPF domain. |
| 1.3.6.1.4.1.43.2.28.2.3.1 | Rowa3ComDvmrpMospfEntry | not-accessible | mandatory | Each entry contains a source subnet in MOSPF domain to be advertised or not to be advertised to the DVMRP domain. |
| 1.3.6.1.4.1.43.2.28.2.3.1.1 | Columna3ComDvmrpMospfIpAddr | read-only | mandatory | Source subnet's IP address. |
| 1.3.6.1.4.1.43.2.28.2.3.1.2 | Columna3ComDvmrpMospfIpMask | read-only | mandatory | This is subnet mask associated with a3ComDvmrpMospfIpAddr. It is a number of contiguous leading 1s, i.e. if the value is 1, it indicates the subnet mask is 128… |
| 1.3.6.1.4.1.43.2.28.2.3.1.3 | Columna3ComDvmrpMospfMetric | read-write | mandatory | The routing metric to this source subnet. It ranges from 1 to 31. |
| 1.3.6.1.4.1.43.2.28.2.3.1.4 | Columna3ComDvmrpMospfAction | read-write | mandatory | If this object is set to aggregate(1), then this source subnet, if learned from MOSPF, is advertised to DVMRP domain in aggregate form. If this object is set t… |
| 1.3.6.1.4.1.43.2.28.2.3.1.5 | Columna3ComDvmrpMospfStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the definition of RowStatus for detail. |
| 1.3.6.1.4.1.43.2.28.2.4 | Tablea3ComDvmrpNeighborTable | not-accessible | mandatory | This table contains a list of neighbors entries for each X.25 or Frame-Relay networks. |
| 1.3.6.1.4.1.43.2.28.2.4.1 | Rowa3ComDvmrpNeighborEntry | not-accessible | mandatory | Each entry contains a single X.25 DTE address or a Frame-Relay DLCI. |
| 1.3.6.1.4.1.43.2.28.2.4.1.1 | Columna3ComDvmrpNeighborPort | read-only | mandatory | The port number to which this entry applies. |
| 1.3.6.1.4.1.43.2.28.2.4.1.2 | Columna3ComDvmrpNeighborType | read-only | mandatory | This object specifies the media type of the port. |
| 1.3.6.1.4.1.43.2.28.2.4.1.3 | Columna3ComDvmrpNeighborAddr | read-only | mandatory | This object specifies an X.25 DTE address or a Frame-Relay DLCI. |
| 1.3.6.1.4.1.43.2.28.2.4.1.4 | Columna3ComDvmrpNeighborStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the definition of RowStatus for detail. |
| 1.3.6.1.4.1.43.2.28.2.5 | Tablea3ComDvmrpTunnelTable | not-accessible | mandatory | This table contains entries of tunnel. |
| 1.3.6.1.4.1.43.2.28.2.5.1 | Rowa3ComDvmrpTunnelEntry | not-accessible | mandatory | Each entry contains parameters associated with a specific tunnel. |
| 1.3.6.1.4.1.43.2.28.2.5.1.1 | Columna3ComDvmrpTunnelId | read-only | mandatory | The ID number of which this entry applies. Tunnel ID starts with 1025 and ends with 1056. |
| 1.3.6.1.4.1.43.2.28.2.5.1.2 | Columna3ComDvmrpTunnelLocalIp | read-write | mandatory | This object specifies the IP address of local end of a tunnel. It must be one of system's directly connected subnet. |
| 1.3.6.1.4.1.43.2.28.2.5.1.3 | Columna3ComDvmrpTunnelRemoteIp | read-write | mandatory | This object specifies the IP address of remote end of a tunnel. |
| 1.3.6.1.4.1.43.2.28.2.5.1.4 | Columna3ComDvmrpTunnelTtl | read-write | mandatory | This object specifies the value to be put in IP packet's TTL field when transmits packets through a tunnel. |
| 1.3.6.1.4.1.43.2.28.2.5.1.5 | Columna3ComDvmrpTunnelStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the definition of RowStatus for detail. |
| 1.3.6.1.4.1.43.2.28.2.6 | Tablea3ComDvmrpAggreExceptTable | not-accessible | mandatory | The table contains list of subnets not to be aggregated. |
| 1.3.6.1.4.1.43.2.28.2.6.1 | Rowa3ComDvmrpAggreExceptEntry | not-accessible | mandatory | Each entry contains a range of subnets. |
| 1.3.6.1.4.1.43.2.28.2.6.1.1 | Columna3ComDvmrpAggreExceptIpAddr | read-write | mandatory | This object specifies the IP subnet address. |
| 1.3.6.1.4.1.43.2.28.2.6.1.2 | Columna3ComDvmrpAggreExceptIpMask | read-write | mandatory | The subnet mask of ccsIpDvmrpAggreExceptIpAddr. It is an integer value representing number of consecutive leading 1s. i.e. if the value is 1, then the subnet m… |
| 1.3.6.1.4.1.43.2.28.2.6.1.3 | Columna3ComDvmrpAggreExceptStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the definition of RowStatus for detail. |
| 1.3.6.1.4.1.43.2.28.2.7 | Tablea3ComDvmrpAggreRangeTable | not-accessible | mandatory | The table contains range of routes to be aggregated. |
| 1.3.6.1.4.1.43.2.28.2.7.1 | Rowa3ComDvmrpAggreRangeEntry | not-accessible | mandatory | Each entry contains a range of routes. |
| 1.3.6.1.4.1.43.2.28.2.7.1.1 | Columna3ComDvmrpAggreRangeIpAddr | read-write | mandatory | This object specifies the IP subnet address. |
| 1.3.6.1.4.1.43.2.28.2.7.1.2 | Columna3ComDvmrpAggreRangeIpMask | read-write | mandatory | The subnet mask of ccsIpDvmrpAggreRangeIpAddr. It is an integer value representing number of consecutive leading 1s. i.e. if the value is 1, then the subnet ma… |
| 1.3.6.1.4.1.43.2.28.2.7.1.3 | Columna3ComDvmrpAggreRangeMetric | read-write | mandatory | This object specifies the cost to the above subnet. If set this object to value 0, the metric associated with the aggregate route to be advertised will pick up… |
| 1.3.6.1.4.1.43.2.28.2.7.1.4 | Columna3ComDvmrpAggreRangeStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the definition of RowStatus for detail. |
| 1.3.6.1.4.1.43.2.28.2.8 | Tablea3ComDvmrpDestGroupTable | not-accessible | mandatory | The table contains destination groups to be or not to be forwarded to MOSPF domain. This table will take effect only if object a3ComDvmrpDestGroupPolicy is set… |
| 1.3.6.1.4.1.43.2.28.2.8.1 | Rowa3ComDvmrpDestGroupEntry | not-accessible | mandatory | Each entry contains a destination group to be or not to be forwarded to MOSPF domain. |
| 1.3.6.1.4.1.43.2.28.2.8.1.1 | Columna3ComDvmrpDestGroupIpAddr | read-only | mandatory | This object specifies the destination group IP address, the first byte in decimal must be in the range of 224 to 239. |
| 1.3.6.1.4.1.43.2.28.2.8.1.2 | Columna3ComDvmrpDestGroupIpMask | read-only | mandatory | This is subnet mask associated with a3ComDvmrpDestGroupIpAddr. It is a number of contiguous leading 1s, i.e. if the value is 1, it indicates the subnet mask is… |
| 1.3.6.1.4.1.43.2.28.2.8.1.3 | Columna3ComDvmrpDestGroupAction | read-write | mandatory | This object specifies if this destination group needs to be forwarded to MOSPF domain. If set to 'accept (1)', the group is forwarded to MOSPF domain; if set t… |
| 1.3.6.1.4.1.43.2.28.2.8.1.4 | Columna3ComDvmrpDestGroupStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the definition of RowStatus for detail. |
| 1.3.6.1.4.1.43.2.28.3 | Nodea3ComDvmrpData | |||
| 1.3.6.1.4.1.43.2.28.3.1 | Tablea3ComDvmrpRouteTable | not-accessible | mandatory | This table contains multicast route information. |
| 1.3.6.1.4.1.43.2.28.3.1.1 | Rowa3ComDvmrpRouteEntry | not-accessible | mandatory | Each entry contains route information to a specific subnet or source. |
| 1.3.6.1.4.1.43.2.28.3.1.1.1 | Columna3ComDvmrpRouteSource | read-only | mandatory | The source IP address of this route. |
| 1.3.6.1.4.1.43.2.28.3.1.1.2 | Columna3ComDvmrpRouteMask | read-only | mandatory | This object is logical-anded with the source address before comparing to the value in previous object a3ComDvmrpRouteSource. |
| 1.3.6.1.4.1.43.2.28.3.1.1.3 | Columna3ComDvmrpRoutePreHop | read-only | mandatory | The IP address of the upstream router of this route. |
| 1.3.6.1.4.1.43.2.28.3.1.1.4 | Columna3ComDvmrpRouteMetric | read-only | mandatory | The routing metric of this route. It's routing-protocol dependenable, for DVMRP, the metric should be in range 1 to 31. The value 32 is considered 'infinity' o… |
| 1.3.6.1.4.1.43.2.28.3.1.1.5 | Columna3ComDvmrpRoutePort | read-only | mandatory | The port number identifies from which this route comes. |
| 1.3.6.1.4.1.43.2.28.3.1.1.6 | Columna3ComDvmrpRouteType | read-only | mandatory | The type of route. |
| 1.3.6.1.4.1.43.2.28.3.1.1.7 | Columna3ComDvmrpRouteStatus | read-only | mandatory | The status of route. |
| 1.3.6.1.4.1.43.2.28.3.1.1.8 | Columna3ComDvmrpRouteProtocol | read-only | mandatory | The routing algorithm to which this route applies. |
| 1.3.6.1.4.1.43.2.28.3.1.1.9 | Columna3ComDvmrpRouteTtl | read-only | mandatory | The time in seconds this route was last updated. |
| 1.3.6.1.4.1.43.2.28.3.1.1.10 | Columna3ComDvmrpRouteChild | read-only | mandatory | This object identifies ports that connect to child subtree of the multicast tree rooted at a3ComDvmrpRouteSource. Each octet, except the first one which contai… |
| 1.3.6.1.4.1.43.2.28.3.1.1.11 | Columna3ComDvmrpRouteChildTunnel | read-only | mandatory | This object is the same as above but includes tunnel ports only. The first (should say the second) octet specifies ports from 1025 (for tunnel port 1) to 1032,… |
| 1.3.6.1.4.1.43.2.28.3.1.1.12 | Columna3ComDvmrpRouteLeaf | read-only | mandatory | This objec identifies ports that connect to leaf subnet of the multicast tree rooted at a3ComDvmrpRouteSource. The value meaning within each octet is the same … |
| 1.3.6.1.4.1.43.2.28.3.1.1.13 | Columna3ComDvmrpRouteLeafTunnel | read-only | mandatory | This objec is the same as a3ComDvmrpRouteLeaf object but includes tunnel ports only. |
| 1.3.6.1.4.1.43.2.28.3.2 | Tablea3ComDvmrpForwardTable | not-accessible | mandatory | This table contains information of each (source, group) pair. |
| 1.3.6.1.4.1.43.2.28.3.2.1 | Rowa3ComDvmrpForwardEntry | not-accessible | mandatory | Each entry contains forwarding information for a specific (source, group) pair. |
| 1.3.6.1.4.1.43.2.28.3.2.1.1 | Columna3ComDvmrpForwardSource | read-only | mandatory | This object specifies root's IP address of this (source, group) multicast distribution tree. |
| 1.3.6.1.4.1.43.2.28.3.2.1.2 | Columna3ComDvmrpForwardGroup | read-only | mandatory | This object specifies the destination multicast group address of this (source, group) multicast distribution tree. |
| 1.3.6.1.4.1.43.2.28.3.2.1.3 | Columna3ComDvmrpForwardTtl | read-only | mandatory | This object specifies the time in seconds left for this (source, group) entry to stay in the forwarding table. When this value reaches 0, this (source, group) … |
| 1.3.6.1.4.1.43.2.28.3.2.1.4 | Columna3ComDvmrpForwardInPort | read-only | mandatory | This object specifies the incoming port for the multicast datagrams from the source a3ComDvmrpForwardSource. |
| 1.3.6.1.4.1.43.2.28.3.2.1.5 | Columna3ComDvmrpForwardOutPorts | read-only | mandatory | This object specifies ports to which multicast datagrams belonging to this (source, group) pair to be forwarded. The value in each octet contains a bit maps of… |
| 1.3.6.1.4.1.43.2.28.3.2.1.6 | Columna3ComDvmrpForwardOutPortsTunnel | read-only | mandatory | This object is the same as a3ComDvmrpForwardOutPorts object but includes tunnel ports mapping only. |
| 1.3.6.1.4.1.43.2.28.3.2.1.7 | Columna3ComDvmrpForwardScoped | read-only | mandatory | This object specifies if it is a boundary port. If the value of this object is yes(1), it means multicast traffic will not be forwarded on the scoped address, … |
| 1.3.6.1.4.1.43.2.28.3.2.1.8 | Columna3ComDvmrpForwardPruneSent | read-only | mandatory | This object specifies if a Prune message has been sent to its upstream router. A prune message is sent when router wants to leave the multicast delivery tree a… |
| 1.3.6.1.4.1.43.2.28.3.3 | Tablea3ComDvmrpNbrRouterTable | not-accessible | mandatory | This table contains information of each neighboring router. |
| 1.3.6.1.4.1.43.2.28.3.3.1 | Rowa3ComDvmrpNbrRouterEntry | not-accessible | mandatory | Each entry contains neighboring router's IP address, DVMRP version, generation ID, expiration time and status. |
| 1.3.6.1.4.1.43.2.28.3.3.1.1 | Columna3ComDvmrpNbrRouterPort | read-only | mandatory | The port number or tunnel ID of which this entry applies. |
| 1.3.6.1.4.1.43.2.28.3.3.1.2 | Columna3ComDvmrpNbrRouterIpAddr | read-only | mandatory | The IP address of this neighboring router. |
| 1.3.6.1.4.1.43.2.28.3.3.1.3 | Columna3ComDvmrpNbrRouterGenId | read-only | mandatory | The generation ID of this neighboring router. |
| 1.3.6.1.4.1.43.2.28.3.3.1.4 | Columna3ComDvmrpNbrRouterVerProtocol | read-only | mandatory | The version of DVMRP protocol that this neighboring router is running. |
| 1.3.6.1.4.1.43.2.28.3.3.1.5 | Columna3ComDvmrpNbrRouterVerMrouted | read-only | mandatory | The version of 'mrouted' that this neighboring router is running. |
| 1.3.6.1.4.1.43.2.28.3.3.1.6 | Columna3ComDvmrpNbrRouterTtl | read-only | mandatory | The time in seconds left for this neighboring router. When the value reaches 0, this entry is deleted from the table. |
| 1.3.6.1.4.1.43.2.28.3.3.1.7 | Columna3ComDvmrpNbrRouterLeafStatus | read-only | mandatory | This object specifies if this neighboring router is a leaf node. |
| 1.3.6.1.4.1.43.2.28.3.3.1.8 | Columna3ComDvmrpNbrRouterPruneStatus | read-only | mandatory | This object specifies if this neighboring router supports DVMRP prune. |
| 1.3.6.1.4.1.43.2.28.3.3.1.9 | Columna3ComDvmrpNbrRouterGenIdStatus | read-only | mandatory | This object specifies if this neighboring router provides generation ID and its router list in the DVMRP probe packet. |
| 1.3.6.1.4.1.43.2.28.3.3.1.10 | Columna3ComDvmrpNbrRouterMtraceStatus | read-only | mandatory | This object specifies if this neighboring router supports multicast trace route. |