A3COM-HUAWEI-POWER-ETH-EXT-MIB
129 objects
Description.
Imported Objects
| A3COM-HUAWEI-OID-MIB | h3cCommon |
| POWER-ETHERNET-MIB | pethMainPseGroupIndex pethPsePortDetectionStatus pethPsePortGroupIndex pethPsePortIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString RowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.43.45.1.10.2.14 | Identityh3cPowerEthernetExt | Description. | ||
| 1.3.6.1.4.1.43.45.1.10.2.14.1 | Tableh3cPsePortTable | not-accessible | current | The indexing scheme is taken form that used by the IETF Power MIB. The same indexing scheme is used to give continuity in behaviour between that standard and t… |
| 1.3.6.1.4.1.43.45.1.10.2.14.1.1 | Rowh3cPsePortEntry | not-accessible | current | The pethPsePortGroupIndex is imported from the IETF Power MIB and uniquely identifies the group containing the port to which power ethernet PSE is connected. G… |
| 1.3.6.1.4.1.43.45.1.10.2.14.1.1.2 | Columnh3cPsePortFaultDescription | read-write | current | The object supports the fault category of the IETF Power MIB [1] pethPsePortDetectionStatus object. A textual description containing more information about the… |
| 1.3.6.1.4.1.43.45.1.10.2.14.1.1.3 | Columnh3cPsePortPeakPower | read-write | current | The object specifies the peak power which has been consumed by the port. It is defined as the highest measured value of power in milliWatts that has been consu… |
| 1.3.6.1.4.1.43.45.1.10.2.14.1.1.4 | Columnh3cPsePortAveragePower | read-write | current | The object specifies the average power which has been consumed by the port. This object is a read/write integer value with units of milliWatts. Writing a value… |
| 1.3.6.1.4.1.43.45.1.10.2.14.1.1.5 | Columnh3cPsePortCurrentPower | read-only | current | The object specifies the power currently being consumed by the port. It is a read only integer value with units of milliWatts. |
| 1.3.6.1.4.1.43.45.1.10.2.14.1.1.6 | Columnh3cPsePortPowerLimit | read-write | current | The object specifies the power limit set for this port. The PSE will not supply more than this level of power to the specified port. It is a read/write integer… |
| 1.3.6.1.4.1.43.45.1.10.2.14.1.1.7 | Columnh3cPsePortProfileIndex | read-write | current | Indicates the power profile which is currently associated with this port. This object references the corresponding h3cPseProfileIndex object in the power profi… |
| 1.3.6.1.4.1.43.45.1.10.2.14.2 | Tableh3cMainPseTable | not-accessible | current | Description. |
| 1.3.6.1.4.1.43.45.1.10.2.14.2.1 | Rowh3cMainPseEntry | not-accessible | current | The pethMainPseGroupIndex is imported from the IETF Power MIB and uniquely identifies the group containing the port to which power ethernet PSE is connected. G… |
| 1.3.6.1.4.1.43.45.1.10.2.14.2.1.1 | Columnh3cMainPsePowerLimit | read-write | current | The object specifies the power limit set for the unit as a whole. The PoE unit will already have a nominal power defined by the IETF Power MIB [1] pethMainPseP… |
| 1.3.6.1.4.1.43.45.1.10.2.14.2.1.2 | Columnh3cMainPseAveragePower | read-write | current | The object specifies the average power which has been consumed by the port. It is a read/write integer value with units of Watts (note - Watts is chosen instea… |
| 1.3.6.1.4.1.43.45.1.10.2.14.2.1.3 | Columnh3cMainPsePeakPower | read-write | current | The object specifies the peak power which has been consumed for PoE. It is defined as the highest measured value of power in milliWatts that has been consumed … |
| 1.3.6.1.4.1.43.45.1.10.2.14.2.1.4 | Columnh3cMainGuaranteedPowerRemaining | read-only | current | The object specifies the amount of power remaining in the guaranteed power pool. Each time a port is placed into guaranteed mode it reserves a set amount of po… |
| 1.3.6.1.4.1.43.45.1.10.2.14.2.1.5 | Columnh3cMainPsePriorityMode | read-write | current | Describes or controls the priority mode on slot which must be enabled firstly. When a new board is inserted, and the power is over-load, a value of disconnecti… |
| 1.3.6.1.4.1.43.45.1.10.2.14.2.1.6 | Columnh3cMainPseLegacy | read-write | current | Describes or controls the legacy mode on slot which must be enabled firstly. Legacy mode: standard or nonstandard PD detection mode. |
| 1.3.6.1.4.1.43.45.1.10.2.14.2.1.7 | Columnh3cMainPsePowerPriority | read-write | current | Describes or controls the priority of the PSE. The priority will be used by the PSE policy to prevent from power overloading. If the priority of PSE is set to … |
| 1.3.6.1.4.1.43.45.1.10.2.14.3 | Scalarh3cPseAutoDetectActive | read-write | current | The object specifies whether the device auto-detection feature is active. If this object is set to Active, and a known powered device is detected, then the por… |
| 1.3.6.1.4.1.43.45.1.10.2.14.4 | Nodeh3cPseComformance | |||
| 1.3.6.1.4.1.43.45.1.10.2.14.4.1 | Nodeh3cPseCompliances | |||
| 1.3.6.1.4.1.43.45.1.10.2.14.4.1.1 | Complianceh3cPseCompliance | current | Description. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.4.2 | Nodeh3cPseGroup | |||
| 1.3.6.1.4.1.43.45.1.10.2.14.4.2.1 | Grouph3cPsePortGroup | current | A collection of objects should be supported at the same time. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.4.2.2 | Grouph3cMainPseGroup | current | A collection of objects should be supported at the same time. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.4.2.3 | Grouph3cPseScalarGroup | current | A collection of scalar objects supported. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.4.2.4 | Grouph3cPsePDNotificationGroup | current | PD Change Notification. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.4.2.5 | Grouph3cPseProfilesGroup | current | A collection of objects should be supported at the same time. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.4.2.6 | Grouph3cPOEPowerThresholdLimitGroup | current | Power threshold limits group. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.4.2.7 | Grouph3cPOEPowerSupInfoGroup | current | The basic Power information group. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.4.2.8 | Grouph3cPOEPowerDCOutStateGroup | current | The DC out power state group. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.4.2.9 | Grouph3cPOEPowerDCOutInfoGroup | current | The power AC input switch information group | |
| 1.3.6.1.4.1.43.45.1.10.2.14.4.2.10 | Grouph3cPOEPowerACSwitchStateModuleGroup | current | PD Change Notification. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.4.2.11 | Grouph3cPOEPowerInCurStateGroup | current | PD Change Notification. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.4.2.12 | Grouph3cPOEPowerAlarmStateGroup | current | PD Change Notification. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.5 | Scalarh3cPsePowerMaxValue | read-write | current | The object specifies the max poe power for lanswitch. The value should between the power currently and the max power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.6 | Nodeh3cpseportNotification | |||
| 1.3.6.1.4.1.43.45.1.10.2.14.6.1 | Notificationh3cpsePDChangeNotification | current | This notification indicates if PD has been inserted or pulled out. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.2 | Notificationh3cPOEDisconnectNotification | current | This notification indicates the POE power module does not disconnect. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.3 | Notificationh3cPOEInputErrorNotification | current | This notification indicates the POE power module input error. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.4 | Notificationh3cPOEOutputErrorNotification | current | This notification indicates the POE power module output error. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.5 | Notificationh3cPOEOverVoltageNotification | current | This notification indicates the POE power module overruns the voltage limit. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.6 | Notificationh3cPOEOverTempNotification | current | This notification indicates the POE power module overruns the temperature limit. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.7 | Notificationh3cPOEFanErrorNotification | current | This notification indicates the POE power module fan error. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.8 | Notificationh3cPOEModuleShutdownNotification | current | This notification indicates the POE power module is closed. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.9 | Notificationh3cPOECurRestrictedNotification | current | This notification indicates the POE power module current is restricted. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.10 | Notificationh3cPOEACSwitchNotification | current | This notification indicates the AC input switch alarm of this POE power. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.11 | Notificationh3cPOEACInCurANotification | current | This notification indicates the AC input current A alarm state of this POE power. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.12 | Notificationh3cPOEACInCurBNotification | current | This notification indicates the AC input current B alarm state of this POE power. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.13 | Notificationh3cPOEACInCurCNotification | current | This notification indicates the AC input current C alarm state of this POE power. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.14 | Notificationh3cPOEACSwitchVolABNotification | current | This notification indicates the AC input voltage AB alarm state of this POE power. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.15 | Notificationh3cPOEACSwitchVolBCNotification | current | This notification indicates the AC input voltage BC alarm state of this POE power. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.16 | Notificationh3cPOEACSwitchVolCANotification | current | This notification indicates the AC input voltage CA alarm state of this POE power. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.17 | Notificationh3cPOEDCOutVolNotification | current | This notification indicates the DC output alarm of this POE power. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.6.18 | Notificationh3cPOEShutdownNotification | current | This notification indicates the whole POE power has been shutdown. | |
| 1.3.6.1.4.1.43.45.1.10.2.14.7 | Tableh3cPseProfilesTable | not-accessible | current | A table of objects representing a set of power profiles. Power profiles can be applied to PoE ports, which have the effect of automatically setting the priorit… |
| 1.3.6.1.4.1.43.45.1.10.2.14.7.1 | Rowh3cPseProfilesEntry | not-accessible | current | A set of objects that display and control the Main power of a PSE. |
| 1.3.6.1.4.1.43.45.1.10.2.14.7.1.1 | Columnh3cPseProfileIndex | not-accessible | current | The index of the profile. This uniquely allow the profile to be identified. |
| 1.3.6.1.4.1.43.45.1.10.2.14.7.1.2 | Columnh3cPseProfileName | read-create | current | Assigns the profile a name with which the settings can be assiciated with. For example, 'NBX Phone'. |
| 1.3.6.1.4.1.43.45.1.10.2.14.7.1.3 | Columnh3cPseProfilePowerMode | read-create | current | The power mode associated with this power profile. There are two possible power modes as follows: powerDisabled, powerEnabled. When a power profile is applied … |
| 1.3.6.1.4.1.43.45.1.10.2.14.7.1.4 | Columnh3cPseProfilePowerLimit | read-create | current | The power limit to be applied to the ports h3cPsePortPowerLimit object when the profile is applied to the PSE port. Expressed in milliWatts. |
| 1.3.6.1.4.1.43.45.1.10.2.14.7.1.5 | Columnh3cPseProfilePriority | read-create | current | This object controls the priority of the port from the point of view of a power management algorithm. The priority that is set by this variable could be used b… |
| 1.3.6.1.4.1.43.45.1.10.2.14.7.1.6 | Columnh3cPseProfilePairs | read-create | current | Describes or controls the pairs in use. If the value of pethPsePortPowerPairsControl is true, this object is writable. A value of signal(1) means that the sign… |
| 1.3.6.1.4.1.43.45.1.10.2.14.7.1.7 | Columnh3cPseProfileApplyNum | read-only | current | The number of this profile which has been applied. If h3cPseProfileApplyNum is not zero, user can't change the current line. |
| 1.3.6.1.4.1.43.45.1.10.2.14.7.1.8 | Columnh3cPseProfileRowStatus | read-create | current | The status of this classifier. If h3cPseProfileApplyNum is not zero, user can't delete the current line. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8 | Nodeh3cPOEPowerObjects | |||
| 1.3.6.1.4.1.43.45.1.10.2.14.8.1 | Nodeh3cPOEThresholdLimitObjs | |||
| 1.3.6.1.4.1.43.45.1.10.2.14.8.1.1 | Scalarh3cPOEThresholdACMimimum | read-write | current | Input threshold AC minimum. It is a read-write node. The value of this node is 'OCTET STRING', it is used to describe a float value. So this string should fit … |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.1.2 | Scalarh3cPOEThresholdACMaximum | read-write | current | Input threshold AC maximum. It is a read-write node. The value of this node is 'OCTET STRING', it is used to describe a float value. So this string should fit … |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.1.3 | Scalarh3cPOEThresholdDCMinimum | read-write | current | Input threshold DC minimum. It is a read-write node. The value of this node is 'OCTET STRING', it is used to describe a float value. So this string should fit … |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.1.4 | Scalarh3cPOEThresholdDCMaximum | read-write | current | Input threshold DC maximum. It is a read-write node. The value of this node is 'OCTET STRING', it is used to describe a float value. So this string should fit … |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.2 | Nodeh3cPOESupModuleInfoObjs | |||
| 1.3.6.1.4.1.43.45.1.10.2.14.8.2.1 | Scalarh3cPOEPowerType | read-only | current | The type of the power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.2.2 | Scalarh3cPOEPowerModuleNum | read-only | current | The number of the power modules. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.2.3 | Scalarh3cPOESupervisionModuleName | read-only | current | The object specifies the Supervision Module name on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.2.4 | Scalarh3cPOESMMajorVersion | read-only | current | The object specifies the high byte of the monitor module version. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.2.5 | Scalarh3cPOESMMinorVersion | read-only | current | The object specifies the low byte of the monitor module version. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.2.6 | Scalarh3cPOESMFactorName | read-only | current | The object specifies the name of the manufactor. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.2.7 | Tableh3cPOEModuleInfoTable | not-accessible | current | The table of the module information on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.2.7.1 | Rowh3cPOEModuleInfoEntry | not-accessible | current | The entry of the module information on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.2.7.1.1 | Columnh3cPOEModuleIndex | accessible-for-notify | current | The index of the current module on this POE power. It is also the index of h3cPOEModuleInfoTable. The range of this node is from 1 to h3cPOEPowerModuleNum. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.2.7.1.2 | Columnh3cPOEModuleID | read-only | current | The ID of the current module on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.2.7.1.3 | Columnh3cPOEModuleInfoPower | read-only | current | The power of the current module on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.2.7.1.4 | Columnh3cPOEModuleHardVerInfo | read-only | current | The hardware version information of the current module on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.3 | Nodeh3cPOEDCOutStateObjects | |||
| 1.3.6.1.4.1.43.45.1.10.2.14.8.3.1 | Scalarh3cPOEDCOutStateModuleNum | read-only | current | The module number on this POE power. It is the maximum of the h3cPOEDCOutStateIndex. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.3.2 | Tableh3cPOEDCOutStateTable | not-accessible | current | The table of DC output power state on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.3.2.1 | Rowh3cPOEDCOutStateEntry | not-accessible | current | The entry of the DC output power state on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.3.2.1.1 | Columnh3cPOEDCOutStateIndex | accessible-for-notify | current | The index of the DC output power state on this POE power. The range of this node is from 1 to h3cPOEDCOutStateModuleNum. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.3.2.1.2 | Columnh3cPOEDCOutDCVolAlarm | read-only | current | The DC output alarm of the DC output power state on this POE power. The value of this node will be the following values: normal (1), underLimit (2), aboveLimit… |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.4 | Nodeh3cPOEDCOutInfoObjects | |||
| 1.3.6.1.4.1.43.45.1.10.2.14.8.4.1 | Scalarh3cPOEDCOutCurNum | read-only | current | The number of DC output current on this POE power. It is the maximum of h3cPOEDCOutInfoIndex. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.4.2 | Tableh3cPOEDCOutInfoTable | not-accessible | current | The table of the DC output information on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.4.2.1 | Rowh3cPOEDCOutInfoEntry | not-accessible | current | The entry of the DC output information on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.4.2.1.1 | Columnh3cPOEDCOutInfoIndex | accessible-for-notify | current | The index of the DC output information on this POE POWER. The range of this node is from 1 to h3cPOEDCOutCurNum. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.4.2.1.2 | Columnh3cPOEDCOutVol | read-only | current | The DC output voltage of the current DC output on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.4.2.1.3 | Columnh3cPOEDCOutInfoLoadCur | read-only | current | The total load current of the current DC output on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.5 | Nodeh3cPOEACSwitchStateModuleObjs | |||
| 1.3.6.1.4.1.43.45.1.10.2.14.8.5.1 | Scalarh3cPOEACSwitchStateModuleNum | read-only | current | The number of the AC swtich state module on this POE power. It is the maximum of h3cPOEACSwitchStateIndex. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.5.2 | Tableh3cPOEACSwitchStateTable | not-accessible | current | The table of the AC switch state on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.5.2.1 | Rowh3cPOEACSwitchStateEntry | not-accessible | current | The entry of the AC switch state on this POE power. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.5.2.1.1 | Columnh3cPOEACSwitchStateIndex | accessible-for-notify | current | The index of the AC switch state on this POE power. The range of this node is from 1 to h3cPOEACSwitchStateModuleNum. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.5.2.1.2 | Columnh3cPOEACSwitchState | read-only | current | The AC switch state on this POE power. The value of this node will be one of the following values: on (1), off (2), highVoltInput (3), lowVoltInput (4) |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.6 | Nodeh3cPOEInCurStateObjects | |||
| 1.3.6.1.4.1.43.45.1.10.2.14.8.6.1 | Scalarh3cPOEInCurStateModuleNum | read-only | current | The DC input current state of the module on this POE power. It is the maximum of the h3cPOESwitchStateVolExIndex. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.6.2 | Scalarh3cPOEInCurAState | read-only | current | The current A state in the DC input on this POE power. normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7… |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.6.3 | Scalarh3cPOEInCurBState | read-only | current | The current B state in the DC input on this POE power. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), … |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.6.4 | Scalarh3cPOEInCurCState | read-only | current | The current C state in the DC input on this POE power. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), … |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.6.5 | Tableh3cPOESwitchStateVolExTable | not-accessible | current | All alarm status of the VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fus… |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.6.5.1 | Rowh3cPOESwitchStateVolExEntry | not-accessible | current | The h3cPOESwitchStateVolExIndex will match the number of the VOL status. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.6.5.1.1 | Columnh3cPOESwitchStateVolExIndex | accessible-for-notify | current | The object species the index of the VOL status. The range of this node is from 1 to h3cPOEInCurStateModuleNum. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.6.5.1.2 | Columnh3cPOESwitchStateInVolAB | read-only | current | The object specifies the VOL AB alarm in each VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3… |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.6.5.1.3 | Columnh3cPOESwitchStateInVolBC | read-only | current | The object specifies the VOL BC alarm in each VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3… |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.6.5.1.4 | Columnh3cPOESwitchStateInVolCA | read-only | current | The object specifies the VOL CA alarm in each VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3… |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.7 | Nodeh3cPOEAlarmStateObjects | |||
| 1.3.6.1.4.1.43.45.1.10.2.14.8.7.1 | Scalarh3cPOEAlarmStateModuleNum | read-only | current | The object specifies the number of the power modules in alarm state. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.7.2 | Tableh3cPOEAlarmStateInfoTable | not-accessible | current | All alarm states in the POE power modules. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1 | Rowh3cPOEAlarmStateInfoEntry | not-accessible | current | The h3cPOEAlarmModuleInfoIndex will match the number of the power module. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.1 | Columnh3cPOEAlarmModuleInfoIndex | accessible-for-notify | current | The index specifies the index of the H3cPOEAlarmStateInfoEntry table. The range of this node is from 1 to h3cPOEAlarmStateModuleNum. |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.2 | Columnh3cPOEModuleDisconnect | read-only | current | The node specifies the alarm state: The module does not link. The value of this node is one of the following values: normal (1), alarm (2). |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.3 | Columnh3cPOEModuleInputError | read-only | current | The node specifies the alarm state: Input error. The value of this node is one of the following values: normal (1), alarm (2). |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.4 | Columnh3cPOEModuleOutputError | read-only | current | The node specifies the alarm state: Output error. The value of this node is one of the following values: normal (1), alarm (2). |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.5 | Columnh3cPOEModuleOverVoltage | read-only | current | The node specifies the alarm state: The voltage is too high. The value of this node is one of the following values: normal (1), alarm (2). |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.6 | Columnh3cPOEModuleOverTemp | read-only | current | The node specifies the alarm state: The temperature is too high. The value of this node is one of the following values: normal (1), alarm (2). |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.7 | Columnh3cPOEModuleFanError | read-only | current | The node specifies the alarm state: The fan error. The value of this node is one of the following values: normal (1), alarm (2). |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.8 | Columnh3cPOEModuleShutdown | read-only | current | The node specifies the alarm state: The module is shutdown. The value of this node is one of the following values: normal (1), alarm (2). |
| 1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.9 | Columnh3cPOEModuleCurRestricted | read-only | current | The node specifies the alarm state: The module limit the current. The value of this node is one of the following values: normal (1), alarm (2). |
| 1.3.6.1.4.1.43.45.1.10.2.14.9 | Scalarh3cPsePolicyMode | read-write | current | The PSE policy only applies to the situation that when a new board (PSE) is inserted, and the power is overload. A value of priority(2) means that the power wi… |
| 1.3.6.1.4.1.43.45.1.10.2.14.10 | Scalarh3cPDPolicyMode | read-write | current | The PD policy only applies to the situation that when a new PD is inserted, and the power of PSE is overload. A value of priority(2) means that the power will … |