A3Com-IPextns-r5-MIB
63 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | enterprises IpAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.43 | Nodea3Com | |||
| 1.3.6.1.4.1.43.2 | NodebrouterMIB | |||
| 1.3.6.1.4.1.43.2.6 | Nodea3ComIPextns | |||
| 1.3.6.1.4.1.43.2.6.1 | Scalara3IPextMode | read-write | mandatory | This object determines the mode the IP protocol layer operates in. When in multipleNet mode, the system will accept different network addresses for each of its… |
| 1.3.6.1.4.1.43.2.6.2 | Scalara3IPextFlushCtl | read-write | mandatory | When set to 2, this object can be used to remove all dynamically learned entries from the IP routing table. When set to 3, this object can be used to remove dy… |
| 1.3.6.1.4.1.43.2.6.3 | Scalara3IPextRelaySrcRteCtl | read-write | mandatory | This object is used to control the relaying of packets that contain the Loose or Strict source route option. If this object is set to relay (1), those packets … |
| 1.3.6.1.4.1.43.2.6.4 | Scalara3IPextSplitLoadCtl | read-write | mandatory | This object is used to control load splitting. If split (1), is specified, the traffic load is distributed among a set of least-equal-cost paths. These paths a… |
| 1.3.6.1.4.1.43.2.6.5 | Scalara3IPicmpInfoCtl | read-write | mandatory | This object determines whether this system replies to ICMP Information request packets. If this object is set to info (1), replies are sent. Otherwise, no repl… |
| 1.3.6.1.4.1.43.2.6.6 | Scalara3IPicmpMaskCtl | read-write | mandatory | This object determines whether this system replies to ICMP Address Mask request packets. If this object is set to mask (1), replies are sent. Otherwise, no rep… |
| 1.3.6.1.4.1.43.2.6.7 | Tablea3IPntmExtTable | not-accessible | mandatory | This table is an extension of the ipNetToMediaTable from mibII. Currently, this table contains objects for controlling MAC header formats and for controlling p… |
| 1.3.6.1.4.1.43.2.6.7.1 | Rowa3IPntmExtEntry | not-accessible | mandatory | Each entry in this table corresponds to an entry in the ipNetToMediaTable. Additional columnar objects are defined in this table that are not in the original t… |
| 1.3.6.1.4.1.43.2.6.7.1.1 | Columna3IPntmIfIndex | read-only | mandatory | The interface on which this entry's equivalence is effective. |
| 1.3.6.1.4.1.43.2.6.7.1.2 | Columna3IPntmNetAddress | read-only | mandatory | The IpAddress corresponding to the media-dependent physical address. |
| 1.3.6.1.4.1.43.2.6.7.1.3 | Columna3IPntmHdrFormat | read-write | mandatory | The header format to be used when sending packets to the destination specified by this table entry. This parameter only applies to networks that support MAC ad… |
| 1.3.6.1.4.1.43.2.6.7.1.4 | Columna3IPntmProxyArp | read-write | mandatory | If this object is set to proxy (1), the system will respond to ARP requests for the IP address of this entry. If this object is set to noProxy (2), no response… |
| 1.3.6.1.4.1.43.2.6.8 | Tablea3IPaddrConfigTable | not-accessible | mandatory | This table contains the IP addresses assigned to each IP port. |
| 1.3.6.1.4.1.43.2.6.8.1 | Rowa3IPaddrConfigEntry | not-accessible | mandatory | Each entry contains a single IP address and parameters relating to routing IP over a specific port. |
| 1.3.6.1.4.1.43.2.6.8.1.1 | Columna3IPaddrConfigPort | read-only | mandatory | The port to which this entry applies. |
| 1.3.6.1.4.1.43.2.6.8.1.2 | Columna3IPaddrConfigAddr | read-only | mandatory | The IP address to which this entry applies. |
| 1.3.6.1.4.1.43.2.6.8.1.3 | Columna3IPaddrConfigType | read-write | mandatory | When multiple IP addresses are configured for a single interface, this object is used to determine which address is the 'primary' address. 'Primary' addresses … |
| 1.3.6.1.4.1.43.2.6.8.1.4 | Columna3IPaddrConfigNetMask | read-write | mandatory | The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the host bits s… |
| 1.3.6.1.4.1.43.2.6.8.1.5 | Columna3IPaddrConfigBcastAddr | read-write | mandatory | The value of the least-significant bit in the IP broadcast address used for sending datagrams on the logical interface associated with the IP address of this e… |
| 1.3.6.1.4.1.43.2.6.8.1.6 | Columna3IPaddrConfigMtu | read-write | mandatory | The size of the largest IP datagram which is supported by the logical interface associated with the IP address of this entry. If this is not specified, the sys… |
| 1.3.6.1.4.1.43.2.6.8.1.7 | Columna3IPaddrConfigStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB. |
| 1.3.6.1.4.1.43.2.6.9 | Tablea3IPforwardExtTable | not-accessible | mandatory | An extension to the ipForwardTable. |
| 1.3.6.1.4.1.43.2.6.9.1 | Rowa3IPforwardExtEntry | not-accessible | mandatory | Each entry in this table corresponds to a single entry in the ipForwardTable. An additional columnar object has been defined to indicate whether a dynamically … |
| 1.3.6.1.4.1.43.2.6.9.1.1 | Columna3IPforwardExtDest | read-only | mandatory | The destination IP address of this route. This is identical to ipForwardDest. |
| 1.3.6.1.4.1.43.2.6.9.1.2 | Columna3IPforwardExtProto | read-only | mandatory | The routing mechanism via which this route was learned. |
| 1.3.6.1.4.1.43.2.6.9.1.3 | Columna3IPforwardExtPolicy | read-only | mandatory | The general set of conditions that would cause the selection of one multipath route (set of next hops for a given destination) is referred to as 'policy'. Unle… |
| 1.3.6.1.4.1.43.2.6.9.1.4 | Columna3IPforwardExtNextHop | read-only | mandatory | On remote routes, the address of the next system en route. Otherwise, 0.0.0.0 |
| 1.3.6.1.4.1.43.2.6.9.1.5 | Columna3IPforwardExtOverride | read-write | mandatory | This object is used to identify those static routes that may be overridden by dynamically learned routes. For those entries in this table that represent dynami… |
| 1.3.6.1.4.1.43.2.6.10 | Scalara3IParpOverBlocked | read-write | mandatory | When the system is in singleNet mode (ie, it is in a bridge state), this parameter controls whether or not ARP request and replies are allowed to be sent or re… |
| 1.3.6.1.4.1.43.2.6.11 | Scalara3IPrarpClientCtl | read-write | mandatory | This allows the RARP client function to be enabled or disabled. If enabled, this system will send RARP requests. If disabled, the system will not send RARP req… |
| 1.3.6.1.4.1.43.2.6.12 | Scalara3IPrarpServerCtl | read-write | mandatory | This allows the RARP server function to be enabled or disabled. If enabled, this system will respond to RARP requests. If disabled, this system will not respon… |
| 1.3.6.1.4.1.43.2.6.13 | Tablea3IParpConfigTable | not-accessible | mandatory | This table contains ARP configuration information. |
| 1.3.6.1.4.1.43.2.6.13.1 | Rowa3IParpConfigEntry | not-accessible | mandatory | Each entry in this table contains port-specific ARP configuration information. |
| 1.3.6.1.4.1.43.2.6.13.1.1 | Columna3IParpPortIndex | read-only | mandatory | The port index to which these entries apply. |
| 1.3.6.1.4.1.43.2.6.13.1.2 | Columna3IParpProxyCtl | read-write | mandatory | This object applies to ARP requests for networks or subnetworks that are in the IP routing table. When this is the case, this system will respond to the reques… |
| 1.3.6.1.4.1.43.2.6.13.1.3 | Columna3IParpHoldTime | read-write | mandatory | This object determines the amount of time, in hours, an entry can stay in the ARP table. When the specified time elapses, the entry is deleted. When one sixtee… |
| 1.3.6.1.4.1.43.2.6.13.1.4 | Columna3IParpReqFormat | read-write | mandatory | This parameter specifies the Ethernet header format used for ARP requests. If this is set to ethernet (1), ARP sends requests with an Ethernet Version 2 header… |
| 1.3.6.1.4.1.43.2.6.13.1.5 | Columna3IParpRemAddr | read-write | mandatory | The value of this object reflects the IP address that is assigned to the boundary router that is attached to this port. This address is used when a RARP reques… |
| 1.3.6.1.4.1.43.2.6.13.1.6 | Columna3IParpInvCtl | read-write | mandatory | This object specifies whether inverse arp is enabled on this port. Note, this affects only Frame Relay ports. |
| 1.3.6.1.4.1.43.2.6.14 | Tablea3IPsmdsGaTable | not-accessible | mandatory | This table contains a set of IP network address to SMDS Group Address pairings. |
| 1.3.6.1.4.1.43.2.6.14.1 | Rowa3IPsmdsGaEntry | not-accessible | mandatory | Each entry in this table contains a single IP network address to SMDS Group Address mapping. This is used in applications running IP over SMDS. |
| 1.3.6.1.4.1.43.2.6.14.1.1 | Columna3IPsmdsGaIpNet | read-only | mandatory | This is an IP network address for which there is a corresponding SMDS Group Address. |
| 1.3.6.1.4.1.43.2.6.14.1.2 | Columna3IPsmdsGa | read-write | mandatory | This is the SMDS Group Address that corresponds to the IP network address identified by a3IPsmdsGaIpNet. |
| 1.3.6.1.4.1.43.2.6.14.1.3 | Columna3IPsmdsGaStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB. |
| 1.3.6.1.4.1.43.2.6.15 | Tablea3IPx25configTable | not-accessible | mandatory | This table contains a set of X25 configuration parameters relating to routing IP over x25 networks. |
| 1.3.6.1.4.1.43.2.6.15.1 | Rowa3IPx25configEntry | not-accessible | mandatory | Each entry contains a set of x25 configuration parameters relating to routing IP over a specific port. |
| 1.3.6.1.4.1.43.2.6.15.1.1 | Columna3IPx25configPort | read-only | mandatory | The port number to which this table entry applies. |
| 1.3.6.1.4.1.43.2.6.15.1.2 | Columna3IPx25configPID | read-write | mandatory | The protocol ID that is included in all outgoing IP packets sent over the x25 port associated with this table entry. |
| 1.3.6.1.4.1.43.2.6.15.1.3 | Columna3IPx25configQueueSize | read-write | deprecated | The maximum number of packets that can be queued for a specific DTE address when the virtual circuit or the x25 port is congested. NOTE: this object is no long… |
| 1.3.6.1.4.1.43.2.6.15.1.4 | Columna3IPx25configVClimit | read-write | deprecated | The maximum number of virtual circuits that can be established concurrently for IP routing. NOTE: this object is no longer supported by NETBuilders running sw … |
| 1.3.6.1.4.1.43.2.6.15.1.5 | Columna3IPx25configVCtimer | read-write | deprecated | The maximum amount of time, in minutes, that can elapse when there is no activity on the x25 virtual circuit before it is cleared. This applies to the first vi… |
| 1.3.6.1.4.1.43.2.6.15.1.6 | Columna3IPx25configProfID | read-write | mandatory | This object specifies the X25 User ProfileID to be used for selecting a Virtual Circuit to send IP Packets. Range is 0..255. If the value specified is 0 then u… |
| 1.3.6.1.4.1.43.2.6.16 | Scalara3IPqueuePriority | read-write | mandatory | This object, which is used by the Multiple Priority Queue feature, specifies into which queue IP packets are placed. If this object has the value default(4), t… |
| 1.3.6.1.4.1.43.2.6.17 | Scalara3IPfwdSubnetBcast | read-write | mandatory | |
| 1.3.6.1.4.1.43.2.6.18 | Tablea3IPicmpGenTable | not-accessible | mandatory | This table contains ICMP configuration information. |
| 1.3.6.1.4.1.43.2.6.18.1 | Rowa3IPicmpGenEntry | not-accessible | mandatory | Each entry in this table contains port-specific ICMP configuration information. |
| 1.3.6.1.4.1.43.2.6.18.1.1 | Columna3IPicmpGenIfIndex | read-only | mandatory | The port to which this entry applies. |
| 1.3.6.1.4.1.43.2.6.18.1.2 | Columna3IPicmpGenRedirect | read-write | mandatory | This object controls whether ICMP issues ReDirect packets on this port. |
| 1.3.6.1.4.1.43.2.6.18.1.3 | Columna3IPicmpGenDestUnreach | read-write | mandatory | This object controls whether ICMP issues Destination Unreachable packets on this port. |
| 1.3.6.1.4.1.43.2.6.18.1.4 | Columna3IPicmpGenTimeExceed | read-write | mandatory | This object controls whether ICMP issues Time Exceeded packets on this port. |