cisco/STAND-ALONE-ETHERNET-SWITCH-MIB
251 objects
No module-level DESCRIPTION found.
Imported Objects
| BRIDGE-MIB | Timeout |
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises Gauge IpAddress TimeTicks |
| RFC1213-MIB | DisplayString ifIndex sysName |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.437 | Nodegrandjunction | |||
| 1.3.6.1.4.1.437.1 | Nodeproducts | |||
| 1.3.6.1.4.1.437.1.1 | NodefastLink | |||
| 1.3.6.1.4.1.437.1.1.2 | NodeseriesG2xx | |||
| 1.3.6.1.4.1.437.1.1.2.1 | NodeesModuleBasic | |||
| 1.3.6.1.4.1.437.1.1.3 | Nodeseries2000 | |||
| 1.3.6.1.4.1.437.1.1.3.0 | NodelogonIntruder | A user is repeatedly trying to logon using an invalid password. The number of attempts exceeds the preset limit given in netMgmtConsolePasswordThresh. Dependin… | ||
| 1.3.6.1.4.1.437.1.1.3.1 | NodeswitchDiagnostic | The switch issues this trap when its Power On Self Test (POST) code does not pass all tests. Some failures are catastrophic and may prevent the generation of t… | ||
| 1.3.6.1.4.1.437.1.1.3.1 | NodesysInfo | |||
| 1.3.6.1.4.1.437.1.1.3.1.1 | ScalarsysInfoFwdEngineRevision | read-only | mandatory | Returns the revision number of the forwarding engine ASIC. |
| 1.3.6.1.4.1.437.1.1.3.1.2 | ScalarsysInfoBoardRevision | read-only | mandatory | Returns the revision number of the switch main board on which the system firmware resides. |
| 1.3.6.1.4.1.437.1.1.3.1.3 | ScalarsysInfoTotalNumberOfPorts | read-only | mandatory | The total number of physical network ports. fixed configuration - 27, 15 or 14 ports modular configuration - 25 - 41 ports This object does NOT represent the u… |
| 1.3.6.1.4.1.437.1.1.3.1.4 | ScalarsysInfoNumberOfSwitchPorts | read-only | mandatory | The number of ports that are individually switched. - 27, 15 or 14 switched ports. Each of these ports has hardware support for a full range of statistics and … |
| 1.3.6.1.4.1.437.1.1.3.1.5 | ScalarsysInfoNumberOfSharedPorts | read-only | mandatory | The number of ports that are collectively switched. fixed configuration - 0 ports modular configuration - 0 to 16 ports Hardware supported statistics are avail… |
| 1.3.6.1.4.1.437.1.1.3.1.6 | ScalarsysInfoNumberOfInstalledModules | read-only | mandatory | The number of high speed switched ports with installed and recognized modules. Hardware supported statistics are available for installed modules. For repeater … |
| 1.3.6.1.4.1.437.1.1.3.1.7 | ScalarsysInfoBuffersUsed | read-only | mandatory | The high-water mark of frame buffer usage in this switch. The initial value upon system reset is zero. |
| 1.3.6.1.4.1.437.1.1.3.1.8 | ScalarsysInfoMaxBuffers | read-only | mandatory | Number of times sysBuffersUsed has reached its maximum value and been reset to zero by the switch. The initial value is zero. |
| 1.3.6.1.4.1.437.1.1.3.1.9 | ScalarsysInfoUtilDisplay | read-only | mandatory | The number of utilization meter LEDs currently lit on the front panel. |
| 1.3.6.1.4.1.437.1.1.3.1.10 | ScalarsysInfoAddrCapacity | read-only | mandatory | The system-wide maximum number of addresses supported. This address capacity includes both dynamic and static address types. |
| 1.3.6.1.4.1.437.1.1.3.1.11 | ScalarsysInfoRestrictedStaticAddrCapacity | read-only | mandatory | The system-wide maximum number of restricted static addresses supported. This object is a subset of sysInfoAddrCapacity. |
| 1.3.6.1.4.1.437.1.1.3.1.12 | ScalarsysInfoPOSTResult | read-only | mandatory | A value which indicates the failures of some particular Power On Self Test (POST). The value is a sum. This sum initially takes the value zero, Then, for each … |
| 1.3.6.1.4.1.437.1.1.3.1.13 | ScalarsysInfoPortFailedPOSTMap | read-only | mandatory | A bit array where the presence of a particular bit indicates a failure of a particular port, as determined by the POST 'individual ports' test. Each octet with… |
| 1.3.6.1.4.1.437.1.1.3.1.14 | ScalarsysInfoPortLinkDisplayMap | read-only | mandatory | A bit array where the presence of a particular bit indicates a lit link LED for a port. Each octet within the value of this object specifies a set of eight lin… |
| 1.3.6.1.4.1.437.1.1.3.1.15 | ScalarsysInfoPortDisabledDisplayMap | read-only | mandatory | A bit array where the presence of a particular bit indicates a lit disabled LED for a port. Each octet within the value of this object specifies a set of eight… |
| 1.3.6.1.4.1.437.1.1.3.1.16 | ScalarsysInfoBroadcastStormLastTime | read-only | mandatory | The last time a port exceeded broadcast threshold. This object is only valid if broadcast storm control is enabled at least once since system start up. The por… |
| 1.3.6.1.4.1.437.1.1.3.1.17 | ScalarsysInfoPortExceedBroadcastStorm | read-only | mandatory | The port where the broadcast threshold was last exceeded, if Broadcast Storm Control was enabled. The time when the event occurred is identified by sysInfoBroa… |
| 1.3.6.1.4.1.437.1.1.3.1.18 | ScalarsysInfoRedundantPowerState | read-only | mandatory | Indicates the state of the redundant power supply. off : the switch is not connected to a redundant power source. healthy : a redundant power source is connect… |
| 1.3.6.1.4.1.437.1.1.3.1.19 | ScalarsysInfoInternalPowerState | read-only | mandatory | Indicates the state of the internal power supply. off : the internal power supply is off. on : the internal power supply is on. |
| 1.3.6.1.4.1.437.1.1.3.1.20 | ScalarsysInfoConfigFileStatus | read-only | mandatory | The status of current or last succesful configuration download since the switch was initialized. The status contains the file name and host the last successful… |
| 1.3.6.1.4.1.437.1.1.3.1.21 | ScalarsysInfoImageCapability | read-only | mandatory | The software image capability supported. |
| 1.3.6.1.4.1.437.1.1.3.2 | NodesysConfig | |||
| 1.3.6.1.4.1.437.1.1.3.2.1 | ScalarsysConfigReset | read-write | mandatory | Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). All parameters including… |
| 1.3.6.1.4.1.437.1.1.3.2.2 | ScalarsysConfigDefaultReset | read-write | mandatory | Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). All configuration parame… |
| 1.3.6.1.4.1.437.1.1.3.2.3 | ScalarsysConfigClearPortStats | read-write | mandatory | Setting this object to noClear(1) results in no action. When set to clear(2), the switch will reset all port statistics to zero. Port statistics are kept in th… |
| 1.3.6.1.4.1.437.1.1.3.2.4 | ScalarsysConfigAddressViolationAction | read-write | mandatory | Indicates what action to take when an address violation (an address mismatch or duplication) occurs on a secured port. The default action is to suspend(1) the … |
| 1.3.6.1.4.1.437.1.1.3.2.5 | ScalarsysConfigAddressViolationAlert | read-write | mandatory | When set to enabled(1), the switch will generate an addressViolation trap upon detecting an address violation on a secured port. When set to disabled(2), no su… |
| 1.3.6.1.4.1.437.1.1.3.2.6 | ScalarsysConfigSwitchingMode | read-write | mandatory | The switch can operate as a high speed cut-through switch, or as a traditional store-and-forward switch. Cut-through switching of frames is enabled when this o… |
| 1.3.6.1.4.1.437.1.1.3.2.7 | ScalarsysConfigMulticastStoreAndForward | read-write | mandatory | When set to enabled(1), the switching of multicast frames will use the store-and-forward method, regardless of the setting of sysConfigSwitchingMode. When set … |
| 1.3.6.1.4.1.437.1.1.3.2.8 | ScalarsysConfigMonitor | read-write | mandatory | Selects whether frames to/from certain ports are sent to sysConfigMonitorPort. A port is selected for monitoring purpose when its portMonitoring object is set … |
| 1.3.6.1.4.1.437.1.1.3.2.9 | ScalarsysConfigMonitorPort | read-write | mandatory | Port number to which all frames to/from monitored ports are sent. Frames are only monitored if the sysConfigMonitor object is set to enabled(1). A number from … |
| 1.3.6.1.4.1.437.1.1.3.2.10 | ScalarsysConfigHigherProtocolMonitor | read-write | obsolete | Selects whether frames addressed to and from the higher- layer protocol processor of the switch are to be monitored. The higher-layer protocol processor is the… |
| 1.3.6.1.4.1.437.1.1.3.2.11 | ScalarsysConfigPort25Connector | read-write | mandatory | Specify which of the two connector types is providing active connection on port 25. Setting the connector to self-sensing allows the switch to learn the active… |
| 1.3.6.1.4.1.437.1.1.3.2.12 | ScalarsysConfigHeuristics | read-write | mandatory | A value which enables special heuristic functions. The value is a sum. This sum initially takes the value zero, Then, for each heuristic function, H, in the ra… |
| 1.3.6.1.4.1.437.1.1.3.2.13 | ScalarsysConfigEnableSTP | read-write | mandatory | The switch implements the 802.1d Spanning Tree Algorithm & Protocol (STP) on all its port to detect loops in the bridge topology. The user may, for any reason,… |
| 1.3.6.1.4.1.437.1.1.3.2.14 | ScalarsysConfigStrictSTPTransition | read-write | deprecated | The 802.1d Spanning Tree Protocol dictates that a port must start out in the blocking state and transition through two other intermediate states (listening and… |
| 1.3.6.1.4.1.437.1.1.3.2.15 | ScalarsysConfigBroadcastStormAction | read-write | mandatory | Indicates what action to take when broadcast threshold is exceeded at a port. block : broadcast packets received from the port are discarded until the broadcas… |
| 1.3.6.1.4.1.437.1.1.3.2.16 | ScalarsysConfigBroadcastStormAlert | read-write | mandatory | When set to enabled(1), the switch will generate a broadcastStormTrap upon detecting that a port is receiving broadcast packets at a rate higher than the speci… |
| 1.3.6.1.4.1.437.1.1.3.2.17 | ScalarsysConfigBroadcastThreshold | read-write | mandatory | This object allows user to set the upper limit for Broadcast storm control function. The broadcast rate is the number of broadcast packets received from a port… |
| 1.3.6.1.4.1.437.1.1.3.2.18 | ScalarsysConfigBroadcastReEnableThreshold | read-write | mandatory | This object allows user to set the re-enable threshold for Broadcast Storm Control function. Once a port has been blocked, the number of broadcast packets rece… |
| 1.3.6.1.4.1.437.1.1.3.2.19 | ScalarsysConfig10MbpsEnhancedCongestionControl | read-write | mandatory | Enhanced Congestion Control (ECC) reduces the transmit back-off period to allow the port to transmit more quickly, thereby reducing the transmit queue congesti… |
| 1.3.6.1.4.1.437.1.1.3.2.20 | ScalarsysConfigNetworkPort | read-write | mandatory | If a network port is configured, all unknown unicast packets are sent only to the network port. Only one port in the switch can be selected as the network port… |
| 1.3.6.1.4.1.437.1.1.3.2.21 | ScalarsysConfigHalfDuplexBackPressure | read-write | mandatory | Back-pressure allows a port to force a collision when there are no buffers to receive frames. Because collision is only meaningful on a port operating in half-… |
| 1.3.6.1.4.1.437.1.1.3.2.22 | ScalarsysConfigFastEthcParmsPort | read-write | mandatory | The parameters of port to use for Fast EtherChannel. Defaults to 26. When Fast EtherChannel is enabled, the following object values parameters are configured t… |
| 1.3.6.1.4.1.437.1.1.3.2.23 | ScalarsysConfigTftpServerName | read-write | mandatory | The TFTP server host name or IP address. The value of this object is the same as upgradeTFTPServerName object. |
| 1.3.6.1.4.1.437.1.1.3.2.24 | ScalarsysConfigConfigFileAuto | read-write | mandatory | Selects whether the system should attempt to retrieve the configuration file on system power-up. When enabled, the system will attempt to retrieve <sysName val… |
| 1.3.6.1.4.1.437.1.1.3.2.25 | ScalarsysConfigPortGroupingMode | read-write | mandatory | When set to bridge-groups (1), the switch allows ports to be assigned to bridge groups. Bridge Group configuration is local to the switch; virtual LANs span ac… |
| 1.3.6.1.4.1.437.1.1.3.3 | NodeaddressViolation | The addressViolation trap is issued when an address violation is detected on a secured port. The generation of the addressViolation trap can be enabled or supp… | ||
| 1.3.6.1.4.1.437.1.1.3.3 | Nodeport | |||
| 1.3.6.1.4.1.437.1.1.3.3.1 | TableswitchPortTable | not-accessible | mandatory | A list of configuration entries for individually switched ports. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1 | RowswPortEntry | not-accessible | mandatory | Configuration parameters for an individually switched port. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.1 | ColumnswPortIndex | read-only | mandatory | Number greater than zero identifying an individually switched port. The same value of a port index variable for any of the port tables in this MIB group select… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.2 | ColumnswPortControllerRevision | read-only | mandatory | Returns the revision number of the port controller. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.3 | ColumnswPortName | read-write | mandatory | A descriptive string of up to 60 characters used by the network administrator to name a port. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.4 | ColumnswPortMediaCapability | read-only | mandatory | The port media capability is one of: other : none of the following private-ethernet : dedicated 10 Mbps Ethernet port general-ethernet : non-dedicated 10 Mbps … |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.5 | ColumnswPortType | read-only | mandatory | Identifies whether the port is other : none of the following network : port does not have address number restriction while it is unsecured. A secured Network p… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.6 | ColumnswPortConnectorType | read-only | mandatory | The type of connector the port is currently using. It is one of other : none of the following (unknown) rj45 : common unshielded twisted pair connector bnc : t… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.7 | ColumnswPortACR | read-write | deprecated | Selects whether Accelerated Congestion Resolution (ACR) should be used on the port. When enabled(1), ACR allows for early frame discard when congestion is expe… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.8 | ColumnswPortFullDuplex | read-write | mandatory | Set to enabled(1) to operate in full duplex mode: port will allow simultaneous transmit and receive which can double its bandwidth. Set to disabled(2) to opera… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.9 | ColumnswPortStatus | read-only | mandatory | Current operational status of the port. Possible values are: enabled : normal operation (transmit and receive) disabled-mgmt : disabled by explicit management … |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.10 | ColumnswPortAdminStatus | read-write | mandatory | By explicit management action, change the port status to either enabled : normal status (transmit and receive enabled) disabled-mgmt: transmit and receive disa… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.11 | ColumnswPortLastStatus | read-only | mandatory | The value of swPortStatus prior to its current value. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.12 | ColumnswPortStatusChanges | read-only | mandatory | Number of times swPortStatus has changed. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.13 | ColumnswPortAddressingSecurity | read-write | mandatory | Set to enabled(1) to effect addressing security. Set to disabled(2) to leave the port unsecure Addressing security cannot be enabled on a port whose type is Ne… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.14 | ColumnswPortAddressTableSize | read-write | mandatory | For secured Network port, the address table size can range from 1 to 132. For unsecured Network port, the size is unrestricted (shown as the value zero) and is… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.15 | ColumnswPortNumberOfLearnedAddresses | read-only | mandatory | The current number of dynamically learned addresses on the port. The initial value is zero. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.16 | ColumnswPortNumberOfStaticAddresses | read-only | mandatory | The current number of statically assigned unicast addresses on the port. The initial value is zero. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.17 | ColumnswPortEraseAddresses | read-write | mandatory | Set to erase(2) to delete all learned and assigned static unicast addresses the port currently has. Setting the object to noErase(1) has no effect. This object… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.18 | ColumnswPortFloodUnregisteredMulticasts | read-write | mandatory | Set to enabled(1) to allow the forwarding to this port frames addressed to multicast addresses that have not been registered for the port. Set to disabled(2) t… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.19 | ColumnswPortFloodUnknownUnicasts | read-write | mandatory | This object controls the forwarding of unknown unicast frames to this port. When set to enabled(1) the switch, upon receiving a frame with an unknown unicast d… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.20 | ColumnswPortMonitoring | read-write | mandatory | Set to enabled(1) to forward receive and transmit frames on this port to the port identified by sysConfigMonitorPort. Set to disabled(2) to not monitor frame t… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.21 | ColumnswPortSecuredAddressViolations | read-only | mandatory | Number of times a source address was seen on this port which duplicates a secured address configured on another port, plus the number of times a source address… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.22 | ColumnswPortLinkbeatStatus | read-only | mandatory | The current port linkbeat status. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.23 | ColumnswPortLinkbeatLosses | read-only | mandatory | Number of times that the value of swPortLinkbeatStatus has changed from linkbeat to noLinkbeat. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.24 | ColumnswPortJabberStatus | read-only | mandatory | The current jabber function result. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.25 | ColumnswPortJabbers | read-only | mandatory | Number of times that the jabber function has to be invoked because a frame transmitted from this port exceeded a certain time duration. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.26 | ColumnswPortClearStatistics | read-write | mandatory | Set to clear(2) to zero out all statistics associated with the port. Per-port statistics are kept in this swPortTable as well as in the swPortRxStatTable, swPo… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.27 | ColumnswPortBroadcastStormBlocked | read-only | mandatory | The current broadcast forwarding status of this port. If this port is blocked by broadcast storm control, the switch drops all broadcasts received from the por… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.28 | ColumnswPortSTPPortFastMode | read-write | mandatory | This object configures the port into the Spanning Tree port-fast mode. When enabled(1), the STP can transition the port's state directly from blocking to forwa… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.29 | ColumnswPortHalfDuplexBackPressure | read-write | obsolete | Back pressure allows a port to force a collision when there is no buffer to receive frames. The port must be in half duplex to benefit from this enhancement. I… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.30 | ColumnswPortDuplexStatus | read-only | mandatory | The status of duplex mode on this port. This shows the result of full duplex auto-negotiation when swPortFullDuplex is set to auto-negotiate. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.31 | ColumnswPortFullDuplexFlowControl | read-write | obsolete | The configuration of flow control on this port. Flow control allows the port to throttle packet transmission according to flow control messages sent by the oth… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.32 | ColumnswPortEnhancedCongestionControl | read-write | mandatory | Enhanced Congestion Control (ECC) reduces the transmit back-off period to allow the port to transmit more quickly, thereby reducing the transmit queue congesti… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.33 | ColumnswPortBridgePriority | read-write | mandatory | This is the bridge port priority. When a port is a non-trunk, the value of this object is the same as dot1dStpPortPriority in RFC 1493 for the port. When a por… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.34 | ColumnswPortBridgePriorityAlternate | read-write | mandatory | This object specifies the other priority that can be used as the port priority for each instance of spanning tree operating on a trunk port. See the definition… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.35 | ColumnswPortBridgePathCost | read-write | mandatory | This is the bridge port path cost. When a port is a non-trunk, the object's value is the same as dot1dStpPortPathCost in RFC 1493 for the port. When a port is … |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.36 | ColumnswPortBridgePathCostAlternate | read-write | mandatory | This object specifies the other path cost that can be used as the port path cost for each instance of spanning tree operating on a trunk port. The value of thi… |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.37 | ColumnswPortIfIndex | read-only | mandatory | This is the value of MIB-II ifIndex object corresponding to this port. |
| 1.3.6.1.4.1.437.1.1.3.3.1.1.38 | ColumnswPortInternal | read-only | mandatory | This indicates if the port is an internal port. An internal port is one that does not allow a direct physical connection to another device. An example of an in… |
| 1.3.6.1.4.1.437.1.1.3.3.2 | TableswitchPortRxStatTable | not-accessible | mandatory | A list of switch port Receive statistics entries. |
| 1.3.6.1.4.1.437.1.1.3.3.2.1 | RowswPortRxStatEntry | not-accessible | mandatory | Receive statistics for an individually switched port. |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.1 | ColumnswPortRxStatIndex | read-only | mandatory | A number greater than zero identifying an individually switched port. The same value of a port index variable for any of the port tables in this MIB group sele… |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.2 | ColumnswPortRxTotalFrames | read-only | mandatory | A count of all frames that are successfully received. This does not include frames received with frame-too-long, FCS, length or alignment errors, or frames los… |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.3 | ColumnswPortRxTotalOctets | read-only | mandatory | A count of data and padding octets in all octets that are successfully received. This does not include octets in frames received with frame-too-long, FCS, leng… |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.4 | ColumnswPortRxTotalOctetsWraps | read-only | mandatory | The number of times the value in swPortRxTotalOctets has rolled to zero. |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.5 | ColumnswPortRxUnicastFrames | read-only | mandatory | A count of frames that are successfully received and are directed to a unicast address. This does not include frames received with frame-too-long, FCS, length … |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.6 | ColumnswPortRxUnicastOctets | read-only | mandatory | A count of data and padding octets in unicast frames that are successfully received. This does not include octets in frames received with frame-too-long, FCS, … |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.7 | ColumnswPortRxUnicastOctetsWraps | read-only | mandatory | The number of times the value in swPortRxUnicastOctets has rolled to zero. |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.8 | ColumnswPortRxBroadcastFrames | read-only | mandatory | A count of frames that are successfully received and are directed to the broadcast address. This does not include frames received with frame-too-long, FCS, len… |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.9 | ColumnswPortRxBroadcastOctets | read-only | mandatory | A count of data and padding octets in broadcast frames that are successfully received. This does not include octets in frames received with frame-too-long, FCS… |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.10 | ColumnswPortRxBroadcastOctetsWraps | read-only | mandatory | The number of times the value in swPortRxBroadcastOctets has rolled to zero. |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.11 | ColumnswPortRxMulticastFrames | read-only | mandatory | A count of frames that are successfully received and are directed to a multicast address. This does not include frames received with frame-too-long, FCS, lengt… |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.12 | ColumnswPortRxMulticastOctets | read-only | mandatory | A count of data and padding octets in multicast frames that are successfully received. This does not include octets in frames received with frame-too-long, FCS… |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.13 | ColumnswPortRxMulticastOctetsWraps | read-only | mandatory | The number of times the value in swPortRxMulticastOctets has rolled to zero. |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.14 | ColumnswPortRxForwardedFrames | read-only | mandatory | Count of frames received and forwarded to some other port(s) for transmission. |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.15 | ColumnswPortRxFilteredFrames | read-only | mandatory | A count of frames received that were discarded because 1) the frames were local to the segment, 2) no destination address matches could be found and no ports w… |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.16 | ColumnswPortRxNoBufferDiscards | read-only | mandatory | A count of frames received that were discarded due to a lack of frame buffer resources in the switch's forwarding engine. |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.17 | ColumnswPortRxFCSErrors | read-only | mandatory | A count of frames received that are an integral number of octets in length but do not pass the Frame Check Sequence test. |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.18 | ColumnswPortRxAlignmentErrors | read-only | mandatory | A count of frames received that are not an integral number of octets in length and do not pass the Frame Check Sequence test. |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.19 | ColumnswPortRxFrameTooLongs | read-only | mandatory | A count of frames received that exceed the maximum permitted frame size as defined by the corresponding portMtu object. |
| 1.3.6.1.4.1.437.1.1.3.3.2.1.20 | ColumnswPortRxRunts | read-only | mandatory | A count of frames received that are shorter than the minimum permitted frame size. Runts usually indicate collision fragments, a normal network event. |
| 1.3.6.1.4.1.437.1.1.3.3.3 | TableswitchPortTxStatTable | not-accessible | mandatory | A list of switch port Transmit statistics entries. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1 | RowswPortTxStatEntry | not-accessible | mandatory | Transmit statistics for an individually switched port. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.1 | ColumnswPortTxStatIndex | read-only | mandatory | A number greater than zero identifying an individually switched port. The same value of a port index variable for any of the port table in this MIB group selec… |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.2 | ColumnswPortTxTotalFrames | read-only | mandatory | A count of all frames that are successfully transmitted. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.3 | ColumnswPortTxTotalOctets | read-only | mandatory | A count of data and padding octets in all frames that are successfully transmitted. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.4 | ColumnswPortTxTotalOctetsWraps | read-only | mandatory | The number of times the value in swPortTxTotalOctets has rolled to zero. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.5 | ColumnswPortTxUnicastFrames | read-only | mandatory | A count of frames that are successfully transmitted and are directed to a unicast address. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.6 | ColumnswPortTxUnicastOctets | read-only | mandatory | A count of data and padding octets in unicast frames that are successfully transmitted. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.7 | ColumnswPortTxUnicastOctetsWraps | read-only | mandatory | The number of times the value in swPortTxUnicastOctets has rolled to zero. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.8 | ColumnswPortTxBroadcastFrames | read-only | mandatory | A count of frames that are successfully transmitted and are directed to the broadcast address. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.9 | ColumnswPortTxBroadcastOctets | read-only | mandatory | A count of data and padding octets in broadcast frames that are successfully transmitted. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.10 | ColumnswPortTxBroadcastOctetsWraps | read-only | mandatory | The number of times the value in swPortTxBroadcastOctets has rolled to zero. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.11 | ColumnswPortTxMulticastFrames | read-only | mandatory | A count of frames that are successfully transmitted and are directed to a multicast address. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.12 | ColumnswPortTxMulticastOctets | read-only | mandatory | A count of data and padding octets in multicast frames that are successfully transmitted. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.13 | ColumnswPortTxMulticastOctetsWraps | read-only | mandatory | The number of times the value in swPortTxMulticastOctets has rolled to zero. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.14 | ColumnswPortTxDeferrals | read-only | mandatory | A count of frames for which the first transmission attempt is delayed because the medium is busy. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.15 | ColumnswPortTxSingleCollisions | read-only | mandatory | A count of successfully transmitted frames for which transmission is inhibited by exactly one collision. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.16 | ColumnswPortTxMultipleCollisions | read-only | mandatory | A count of successfully transmitted frames for which transmission is inhibited by more than one collision. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.17 | ColumnswPortTxLateCollisions | read-only | mandatory | The number of times that a collision is detected later than 512 bit-times into the transmission of a frame. A late collision is also considered as a (generic) … |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.18 | ColumnswPortTxExcessiveCollisions | read-only | mandatory | A count of frames for which transmission fails due to excessive collisions. The threshold is either 16 in the normal mode of operation, or 4 in the Enhanced Co… |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.19 | ColumnswPortTxExcessiveDeferrals | read-only | mandatory | A count of frames for which transmission is deferred for an excessive period of time. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.20 | ColumnswPortTxExcessiveCollision16s | read-only | mandatory | A count of frames that due to excessive collisions are not transmitted successfully. Here, the normal threshold of 16 collisions is used to determine the statu… |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.21 | ColumnswPortTxExcessiveCollision4s | read-only | mandatory | A count of frames that due to excessive collisions are not transmitted successfully. Here, the Enhanced Congestion Control threshold of 4 collisions is used to… |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.22 | ColumnswPortTxQueueFullDiscards | read-only | mandatory | A count of frames that cannot be transmitted because the transmit queue for the port is full. |
| 1.3.6.1.4.1.437.1.1.3.3.3.1.23 | ColumnswPortTxErrors | read-only | mandatory | A count of frames for which transmission fails due to an internal MAC sublayer transmit error. A frame is only counted by an instance of this object if it is n… |
| 1.3.6.1.4.1.437.1.1.3.3.4 | TableswitchPortTxCollTable | not-accessible | mandatory | A collection of collision histograms for the switch ports. |
| 1.3.6.1.4.1.437.1.1.3.3.4.1 | RowswPortTxCollEntry | not-accessible | mandatory | This table provides a per port histogram of collision activity. The swPortTxCollIndex index (1 to sysInfoNumberOfSwitchPorts) identifies an individually switch… |
| 1.3.6.1.4.1.437.1.1.3.3.4.1.1 | ColumnswPortTxCollIndex | read-only | mandatory | A number greater than zero identifying an individually switched port. The same value of a port index variable for any of the port tables in this MIB group sele… |
| 1.3.6.1.4.1.437.1.1.3.3.4.1.2 | ColumnswPortTxCollCount | read-only | mandatory | The number of per-frame media collisions for which a particular collision histogram cell represents the frequency on a particular port. |
| 1.3.6.1.4.1.437.1.1.3.3.4.1.3 | ColumnswPortTxCollFrequencies | read-only | mandatory | A count of frames for which the transmission (successful or otherwise) on a particular port is accompanied by a particular number of media collisions. |
| 1.3.6.1.4.1.437.1.1.3.4 | NodebroadcastStorm | The broadcastStorm trap is issued when broadcast storm control is enabled and the number of broadcast packets received in a second from a port is higher than t… | ||
| 1.3.6.1.4.1.437.1.1.3.4 | NodenetMgmt | |||
| 1.3.6.1.4.1.437.1.1.3.4.1 | ScalarnetMgmtIpAddress | read-write | mandatory | The switch's administrative IP address. The switch may automatically discover a value for this object using the BootStrap protocol (BOOTP). The object value is… |
| 1.3.6.1.4.1.437.1.1.3.4.2 | ScalarnetMgmtIpSubnetMask | read-write | mandatory | The switch's administrative IP subnet mask. The switch may automatically discover a value for this object using the BootStrap protocol (BOOTP). The object valu… |
| 1.3.6.1.4.1.437.1.1.3.4.3 | ScalarnetMgmtDefaultGateway | read-write | mandatory | The default gateway IP address is the address of the next hop router the switch uses to reach a non-local IP host when the switch does not know the return rout… |
| 1.3.6.1.4.1.437.1.1.3.4.4 | ScalarnetMgmtEnableAuthenTraps | read-write | mandatory | Indicates whether the switch is permitted to generate authenticationFailure traps. The value of this object overrides any configuration information; as such, i… |
| 1.3.6.1.4.1.437.1.1.3.4.5 | ScalarnetMgmtEnableLinkTraps | read-write | mandatory | Indicates whether the switch is permitted to generate linkUp/linkDown traps. The value of this object overrides any configuration information; as such, it prov… |
| 1.3.6.1.4.1.437.1.1.3.4.6 | ScalarnetMgmtConsoleInactTime | read-write | mandatory | The number of seconds of Management Console session inactivity to wait before ending the session. Once a session has ended, the user must resupply the Console … |
| 1.3.6.1.4.1.437.1.1.3.4.7 | ScalarnetMgmtConsolePasswordThresh | read-write | mandatory | The number of consecutive invalid password attempts allowed before the Management Console is shut down (kept silent) for a configured duration. A zero value pe… |
| 1.3.6.1.4.1.437.1.1.3.4.8 | ScalarnetMgmtConsoleSilentTime | read-write | mandatory | The number of minutes during which the Management Console will be unavailable after repeated failed attempts to logon. A zero value specifies no silent time, a… |
| 1.3.6.1.4.1.437.1.1.3.4.9 | ScalarnetMgmtModemInitString | read-write | mandatory | This is the initialization string used to configure an attached modem. Specify this string if the modem is not Hayes compatible. Only the initialization comman… |
| 1.3.6.1.4.1.437.1.1.3.4.10 | ScalarnetMgmtModemDialString | read-write | mandatory | This string contains a phone number which is used to establish a modem connection with a remote site. Only the phone number needs to be specified (i.e., do NOT… |
| 1.3.6.1.4.1.437.1.1.3.4.11 | ScalarnetMgmtModemDialDelay | read-write | mandatory | This object specifies a delay in seconds between every dial-out failure. The value zero indicates an infinite delay. Normally, the switch will attempt a dial-o… |
| 1.3.6.1.4.1.437.1.1.3.4.12 | ScalarnetMgmtModemAutoAnswer | read-write | mandatory | This object specifies whether the system should be in auto-answer mode and only accepts incoming calls. Note that the system will always attempt a dial-out fir… |
| 1.3.6.1.4.1.437.1.1.3.4.13 | TablenetMgmtSetClientTable | not-accessible | mandatory | Table (4 entries) containing a list of IP addresses or DNS name of workstations permitted to issue SET requests. Such a workstation is called a Set client. If … |
| 1.3.6.1.4.1.437.1.1.3.4.13.1 | RownetMgmtSetClientEntry | not-accessible | mandatory | An IP address of a manager station allowed to issue SET requests to this management agent. |
| 1.3.6.1.4.1.437.1.1.3.4.13.1.1 | ColumnnetMgmtSetClientIndex | read-only | mandatory | Identification of a SET client entry. |
| 1.3.6.1.4.1.437.1.1.3.4.13.1.2 | ColumnnetMgmtSetClientAddr | read-write | mandatory | The SET client is assumed to be Internet UDP/IP based. And this is the client's IP address. Setting this object will cause the value in the corresponding netMg… |
| 1.3.6.1.4.1.437.1.1.3.4.13.1.3 | ColumnnetMgmtSetClientStatus | read-write | mandatory | Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry. That is, it effectively disassociates the IP address identi… |
| 1.3.6.1.4.1.437.1.1.3.4.13.1.4 | ColumnnetMgmtSetClientName | read-write | mandatory | The Set Client's DNS host name. The switch will resolve the host name to IP address via DNS and copy the resolved IP address into netMgmtSetClientAddr object. … |
| 1.3.6.1.4.1.437.1.1.3.4.14 | TablenetMgmtTrapClientTable | not-accessible | mandatory | Table (4 entries) containing a list of Network Management Stations that are to receive traps generated by this Network Management Agent. Such an NMS is called … |
| 1.3.6.1.4.1.437.1.1.3.4.14.1 | RownetMgmtTrapClientEntry | not-accessible | mandatory | A destination address and community string to a particular trap client. |
| 1.3.6.1.4.1.437.1.1.3.4.14.1.1 | ColumnnetMgmtTrapClientIndex | read-only | mandatory | Identification of a trap client entry. |
| 1.3.6.1.4.1.437.1.1.3.4.14.1.2 | ColumnnetMgmtTrapClientAddr | read-write | mandatory | The trap client is assumed to be Internet UDP/IP based. And this is the client's IP address. Setting a value for this object will cause the value of netMgmtTra… |
| 1.3.6.1.4.1.437.1.1.3.4.14.1.3 | ColumnnetMgmtTrapClientComm | read-write | mandatory | Community string used for traps sent to this trap client. |
| 1.3.6.1.4.1.437.1.1.3.4.14.1.4 | ColumnnetMgmtTrapClientStatus | read-write | mandatory | Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry. That is, it effectively disassociates the IP address/commun… |
| 1.3.6.1.4.1.437.1.1.3.4.14.1.5 | ColumnnetMgmtTrapClientName | read-write | mandatory | The Trap Client's DNS host name. The switch will resolve the host name to an IP address via DNS and copy the resolved IP address into netMgmtTrapClientAddr obj… |
| 1.3.6.1.4.1.437.1.1.3.4.15 | ScalarnetMgmtCdpHoldTime | read-write | mandatory | The hold time is the amount of time that a neighboring device keeps the CDP neighbor information received from this switch. If the hold time expires before rec… |
| 1.3.6.1.4.1.437.1.1.3.4.16 | ScalarnetMgmtCdpTransmissionTime | read-write | mandatory | The transmission time specifies the interval that the switch will trasnmit CDP messages from its ports. The default value is 60 seconds. |
| 1.3.6.1.4.1.437.1.1.3.4.17 | ScalarnetMgmtCgmpEnable | read-write | mandatory | This variable allows user to enable or disable Cisco Group Management Protocol (CGMP). Enabling CGMP will result in the deletion of all multicast addresses of … |
| 1.3.6.1.4.1.437.1.1.3.4.18 | ScalarnetMgmtCgmpRouterHoldTime | read-write | mandatory | Multicast routers that support CGMP will send CGMP join message to advertise themselves to switches within a network. A switch that receives a CGMP message wil… |
| 1.3.6.1.4.1.437.1.1.3.4.19 | ScalarnetMgmtVlan | read-write | mandatory | The current VLAN for network management. This defaults to 1. |
| 1.3.6.1.4.1.437.1.1.3.4.20 | ScalarnetMgmtEnableRIP | read-write | mandatory | This object enables and disables Routing Information Protocol (RIP) listener to automatically discover IP gateways. The default value is enabled(1). |
| 1.3.6.1.4.1.437.1.1.3.4.21 | ScalarnetMgmtDomainServer1IpAddress | read-write | mandatory | The IP address of a Domain Name Server (DNS) which the system uses to resolve domain names to IP addresses. A set on this object takes effect the next time the… |
| 1.3.6.1.4.1.437.1.1.3.4.22 | ScalarnetMgmtDomainServer2IpAddress | read-write | mandatory | The IP address of a second Domain Name Server (DNS) which the system uses to resolve domain names to IP addresses. A set on this object takes effect the next t… |
| 1.3.6.1.4.1.437.1.1.3.4.23 | ScalarnetMgmtDefaultSearchDomain | read-write | mandatory | A string of up to 63 characters specifying a default domain search path. When switch needs to resolve a domain name that is not fully specified, it appends thi… |
| 1.3.6.1.4.1.437.1.1.3.4.24 | ScalarnetMgmtHttpServerAdminState | read-write | mandatory | This variable enables or disables the HTTP server interface. The default value is enabled(1). |
| 1.3.6.1.4.1.437.1.1.3.4.25 | ScalarnetMgmtHttpPort | read-write | mandatory | This variable allows the user to configure a specific port on which the HTTP server will listen for TCP connections. By default, the server listens on TCP port… |
| 1.3.6.1.4.1.437.1.1.3.5 | NoderpsFailed | A redundant power source is connected to the switch but a failure exists in the power system. | ||
| 1.3.6.1.4.1.437.1.1.3.5 | Nodeupgrade | |||
| 1.3.6.1.4.1.437.1.1.3.5.1 | ScalarupgradeFirmwareSource | read-write | mandatory | Selects the source from which firmware is read. There are 2 possible values, eprom(1) and flash(2). A valid selection will cause a system reset, followed by th… |
| 1.3.6.1.4.1.437.1.1.3.5.2 | ScalarupgradeEPROMRevision | read-only | mandatory | Returns the revision number of the switch system firmware residing in EPROM. The string has the following format 'V2.01'. |
| 1.3.6.1.4.1.437.1.1.3.5.3 | ScalarupgradeFlashSize | read-only | mandatory | The size of available FLASH memory in the system, in kilobytes. For example: 128 equals 131072 bytes (128 bytes times 1024). |
| 1.3.6.1.4.1.437.1.1.3.5.4 | ScalarupgradeFlashBankStatus | read-only | mandatory | Text string indicating status and version of last upgrade to flash memory, including the source of the upgrade, version and the date and time of upgrade. The s… |
| 1.3.6.1.4.1.437.1.1.3.5.5 | ScalarupgradeTFTPServerAddress | read-write | mandatory | The IP address of a TFTP server from which a firmware image can be downloaded. The download may be initiated by setting the upgradeTFTPInitiate to upgrade(1), … |
| 1.3.6.1.4.1.437.1.1.3.5.6 | ScalarupgradeTFTPLoadFilename | read-write | mandatory | The name of the file containing a firmware upgrade image on the host whose address is given by upgradeTFTPServerAddress. The default value is an empty string, … |
| 1.3.6.1.4.1.437.1.1.3.5.7 | ScalarupgradeTFTPInitiate | read-write | mandatory | Setting this object to noUpgrade(2) results in no action. When set to upgrade(1), the switch will attempt to download a firmware upgrade image from the server … |
| 1.3.6.1.4.1.437.1.1.3.5.8 | ScalarupgradeAutoExecute | read-write | mandatory | Indicates whether a newly upgraded firmware version should immediately be selected for execution. When this object is disabled(2), the user must explicitly set… |
| 1.3.6.1.4.1.437.1.1.3.5.9 | ScalarupgradeTFTPAccept | read-write | mandatory | This object controls the second method of firmware upgrade using TFTP. The switch has a UDP Listener on the well known TFTP server port, and can accept upgrade… |
| 1.3.6.1.4.1.437.1.1.3.5.10 | ScalarupgradeTFTPServerName | read-write | mandatory | The name of a TFTP server DNS name from which a firmware image can be downloaded. The download may be initiated by setting the upgradeTFTPInitiate to upgrade(1… |
| 1.3.6.1.4.1.437.1.1.3.6 | NodeipAddressChange | The ipAddressChange trap is issued when the switch is unable to complete its DHCPDISCOVER/ DHCPREQUEST process, or when it fails to extend the lease for the cu… | ||
| 1.3.6.1.4.1.437.1.1.3.6 | Nodevlan | |||
| 1.3.6.1.4.1.437.1.1.3.6.1 | ScalarvlanMaxSupported | read-only | mandatory | The maximum number of virtual LANs supported. |
| 1.3.6.1.4.1.437.1.1.3.6.2 | ScalarvlanAllowMembershipOverlap | read-write | deprecated | When set to enabled(1), the switch will allow a port to be member of more than one VLAN. Note that overlapped VLANs may lead to loss of connectivity in the Spa… |
| 1.3.6.1.4.1.437.1.1.3.6.3 | TablevlanTable | not-accessible | mandatory | A list of configuration entries for a VLAN. |
| 1.3.6.1.4.1.437.1.1.3.6.3.1 | RowvlanEntry | not-accessible | mandatory | Configuration parameters for a VLAN. |
| 1.3.6.1.4.1.437.1.1.3.6.3.1.1 | ColumnvlanIndex | read-only | mandatory | Number from 1 to vlanMaxSupported identifying a configurable VLAN. |
| 1.3.6.1.4.1.437.1.1.3.6.3.1.2 | ColumnvlanName | read-write | mandatory | A descriptive string of up to 60 characters used by the network administrator to name a VLAN. This object is not supported by switches operating with firmware … |
| 1.3.6.1.4.1.437.1.1.3.6.3.1.3 | ColumnvlanMemberPorts | read-only | mandatory | The set of the switch's member ports for the VLAN. A port may reside within multiple VLANs only if the object vlanAllowMembershipOverlap has been set to enable… |
| 1.3.6.1.4.1.437.1.1.3.6.3.1.4 | ColumnvlanIpAddress | read-write | mandatory | The switch's administrative IP address in this VLAN. Note that once a value has been set for this object, the next write will only take effect after a system r… |
| 1.3.6.1.4.1.437.1.1.3.6.3.1.5 | ColumnvlanIpSubnetMask | read-write | mandatory | The switch's administrative IP subnet mask in this VLAN. A change in the subnet mask at any time will immediately take effect. The default value is the same as… |
| 1.3.6.1.4.1.437.1.1.3.6.3.1.6 | ColumnvlanBridgeTemplate | read-write | mandatory | The bridge parameter template used by the VLAN. By default, a VLAN uses template 1. The value of this object must be one of the values of bridgeTemplateIndex. … |
| 1.3.6.1.4.1.437.1.1.3.6.3.1.7 | ColumnvlanStpAdmin | read-write | mandatory | This object indicates if STP is enabled or disabled for the VLAN. This object is supported only by switches operating with firmware version greater than or equ… |
| 1.3.6.1.4.1.437.1.1.3.6.4 | TablevlanMemberTable | not-accessible | mandatory | A list of port membership configuration entries for a VLAN. |
| 1.3.6.1.4.1.437.1.1.3.6.4.1 | RowvlanMemberEntry | not-accessible | mandatory | Port membership configuration parameters for a VLAN. |
| 1.3.6.1.4.1.437.1.1.3.6.4.1.1 | ColumnvlanMemberIndex | read-only | mandatory | Number from 1 to vlanMaxSupported identifying a configurable VLAN. The same value of a VLAN index variable for any of the VLAN tables in this MIB group selects… |
| 1.3.6.1.4.1.437.1.1.3.6.4.1.2 | ColumnvlanMemberPortIndex | read-only | mandatory | Number greater than zero identifying an individually switched port. The same value of a port index variable for any of the port tables selects the same port. |
| 1.3.6.1.4.1.437.1.1.3.6.4.1.3 | ColumnvlanMemberPortOfVlan | read-write | mandatory | The port identified by vlanMemberPortIndex becomes a member of the VLAN identified by vlanMemberIndex when this object is set to true(1). The same port ceases … |
| 1.3.6.1.4.1.437.1.1.3.6.5 | ScalarbridgeTemplateMax | read-only | mandatory | The maximum number of bridge templates supported. |
| 1.3.6.1.4.1.437.1.1.3.6.6 | TablebridgeTemplateTable | not-accessible | mandatory | A list of bridge configuration templates. |
| 1.3.6.1.4.1.437.1.1.3.6.6.1 | RowbridgeTemplateEntry | not-accessible | mandatory | Configuration parameters for a bridge parameter template. |
| 1.3.6.1.4.1.437.1.1.3.6.6.1.1 | ColumnbridgeTemplateIndex | read-only | mandatory | Number from 1 to bridgeTemplateMax identifying a configurable bridge parameters template. |
| 1.3.6.1.4.1.437.1.1.3.6.6.1.2 | ColumnbridgeTemplatePriority | read-write | mandatory | See dot1dStpPriority in RFC 1493. The value of dot1dStpPriority must match the value of an instance of this object. |
| 1.3.6.1.4.1.437.1.1.3.6.6.1.3 | ColumnbridgeTemplateMaxAge | read-write | mandatory | See dot1dStpBridgeMaxAge in RFC 1493. The value of dot1dStpBridgeMaxAge must match the value of an instance of this object. |
| 1.3.6.1.4.1.437.1.1.3.6.6.1.4 | ColumnbridgeTemplateHelloTime | read-write | mandatory | See dot1dStpBridgeHelloTime in RFC 1493. The value of dot1dStpBridgeHelloTime must match the value of an instance of this object. |
| 1.3.6.1.4.1.437.1.1.3.6.6.1.5 | ColumnbridgeTemplateForwardDelay | read-write | mandatory | See dot1dStpBridgeForwardDelay in RFC 1493. The value of dot1dStpBridgeForwardDelay must match the value of an instance of this object. |
| 1.3.6.1.4.1.437.1.1.3.7 | NodebandwidthUsage | |||
| 1.3.6.1.4.1.437.1.1.3.7.1 | ScalarbandwidthUsageCurrent | read-only | mandatory | The bandwidth currently consumed. The measurement unit is in megabits per second (1,000,000 bits/second). |
| 1.3.6.1.4.1.437.1.1.3.7.2 | ScalarbandwidthUsageMaxPeakEntries | read-only | mandatory | The maximum number of entries bandwidthUsagePeakTable can have. |
| 1.3.6.1.4.1.437.1.1.3.7.3 | ScalarbandwidthUsagePeakInterval | read-write | mandatory | This object specifies the length of time which forms a peak bandwidth capture interval. The default is oneday(24). A write to this object with any new value re… |
| 1.3.6.1.4.1.437.1.1.3.7.4 | ScalarbandwidthUsagePeakRestart | read-write | mandatory | Set to restart(2) to clear the bandwidthUsagePeakTable and restart the peak bandwidth capturing at the current interval. No action will be taken if this object… |
| 1.3.6.1.4.1.437.1.1.3.7.5 | ScalarbandwidthUsageCurrentPeakEntry | read-only | mandatory | A value identifying an instance of the bandwidthUsagePeakIndex of the bandwidthUsagePeakTable where the peak bandwidth measurement is most current. |
| 1.3.6.1.4.1.437.1.1.3.7.6 | TablebandwidthUsagePeakTable | not-accessible | mandatory | A list of entries containing peak bandwidth usages in a number of time periods. |
| 1.3.6.1.4.1.437.1.1.3.7.6.1 | RowbandwidthUsagePeakEntry | not-accessible | mandatory | Information about peak bandwidth usage in a time period. |
| 1.3.6.1.4.1.437.1.1.3.7.6.1.1 | ColumnbandwidthUsagePeakIndex | read-only | mandatory | Number from 1 to bandwidthUsageMaxPeakEntries identifying a particular bandwithUsagePeakEntry. |
| 1.3.6.1.4.1.437.1.1.3.7.6.1.2 | ColumnbandwidthUsageStartTime | read-only | mandatory | Up to 32 characters containing the date and time that marks the start of this capture interval. The string is in net ASCII and conforms exactly to the followin… |
| 1.3.6.1.4.1.437.1.1.3.7.6.1.3 | ColumnbandwidthUsagePeak | read-only | mandatory | The highest bandwidth utilized since the time given in bandwidthUsageStartTime or last cleared. The measurement unit is in megabits per second (1,000,000 bits/… |
| 1.3.6.1.4.1.437.1.1.3.7.6.1.4 | ColumnbandwidthUsagePeakTime | read-only | mandatory | Up to 32 characters containing the date and time the value in bandwidthUsagePeak is captured. The string is in net ASCII and conforms exactly to the following … |
| 1.3.6.1.4.1.437.1.1.3.8 | NodebridgeGroup | |||
| 1.3.6.1.4.1.437.1.1.3.8.1 | ScalarbridgeGroupMaxSupported | read-only | mandatory | The maximum number of bridge groups supported. The switch currenlty supports up to 4 bridge groups. This object represents the upper bound of the index into th… |
| 1.3.6.1.4.1.437.1.1.3.8.2 | ScalarbridgeGroupAllowMembershipOverlap | read-write | mandatory | When set to enabled(1), the switch will allow a port to be member of more than one bridge group. Note that overlapped bridge groups may lead to loss of connect… |
| 1.3.6.1.4.1.437.1.1.3.8.3 | TablebridgeGroupTable | not-accessible | mandatory | A list of configuration entries for a bridge group. |
| 1.3.6.1.4.1.437.1.1.3.8.3.1 | RowbridgeGroupEntry | not-accessible | mandatory | Configuration parameters for a bridge group. |
| 1.3.6.1.4.1.437.1.1.3.8.3.1.1 | ColumnbridgeGroupIndex | read-only | mandatory | Number from 1 to bridgeGroupMaxSupported identifying a configurable bridge group. |
| 1.3.6.1.4.1.437.1.1.3.8.3.1.3 | ColumnbridgeGroupMemberPorts | read-only | mandatory | The set of the switch's member ports for the bridge group. A port may reside within multiple bridge groups only if the object bridgeGroupAllowMembershipOverlap… |
| 1.3.6.1.4.1.437.1.1.3.8.3.1.4 | ColumnbridgeGroupStpAdmin | read-write | mandatory | This object indicates if STP is enabled or disabled for the bridge group. The default is enabled(1). |
| 1.3.6.1.4.1.437.1.1.3.8.4 | TablebridgeGroupMemberTable | not-accessible | mandatory | A list of port membership configuration entries for a bridge group. |
| 1.3.6.1.4.1.437.1.1.3.8.4.1 | RowbridgeGroupMemberEntry | not-accessible | mandatory | Port membership configuration parameters for a bridge group. |
| 1.3.6.1.4.1.437.1.1.3.8.4.1.1 | ColumnbridgeGroupMemberIndex | read-only | mandatory | The value of bridgeGroupIndex of a bridge group. |
| 1.3.6.1.4.1.437.1.1.3.8.4.1.2 | ColumnbridgeGroupMemberPortIndex | read-only | mandatory | The value of swPortIndex of a switched port. |
| 1.3.6.1.4.1.437.1.1.3.8.4.1.3 | ColumnbridgeGroupMemberPortOfBridgeGroup | read-write | mandatory | The port identified by bridgeGroupMemberPortIndex becomes a member of the bridgeGroup identified by bridgeGroupMemberIndex when this object is set to true(1). … |