A3COM-SWITCHING-SYSTEMS-QOS-MIB
89 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | enterprises Gauge IpAddress |
| RFC1213-MIB | DisplayString ifIndex |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.43 | Nodea3Com | |||
| 1.3.6.1.4.1.43.29 | NodeswitchingSystemsMibs | |||
| 1.3.6.1.4.1.43.29.4 | Nodea3ComSwitchingSystemsMib | |||
| 1.3.6.1.4.1.43.29.4.21 | Nodea3ComQos | |||
| 1.3.6.1.4.1.43.29.4.21.1 | Nodea3ComQosClass | |||
| 1.3.6.1.4.1.43.29.4.21.1.1 | Tablea3ComQosGenClassTable | not-accessible | mandatory | This table lists all QoS classes (Flow and Non-Flow) configured in the system. |
| 1.3.6.1.4.1.43.29.4.21.1.1.1 | Rowa3ComQosGenClassEntry | not-accessible | mandatory | An entry describing a single class entity. |
| 1.3.6.1.4.1.43.29.4.21.1.1.1.1 | Columna3ComQosGenClassIndex | read-only | mandatory | A unique value for each entry. |
| 1.3.6.1.4.1.43.29.4.21.1.1.1.2 | Columna3ComQosGenClassName | read-write | mandatory | A textual name for the class. |
| 1.3.6.1.4.1.43.29.4.21.1.1.1.3 | Columna3ComQosGenClassControlId | read-write | mandatory | The control entry that this class is associated with. Note that the user must have created the control (via the a3ComQosCtrlTable) before making the associatio… |
| 1.3.6.1.4.1.43.29.4.21.1.2 | Tablea3ComQosFlowClassTable | not-accessible | mandatory | This table lists the Flow classes defined in the system. A Flow class applies only to IP unicast and multicast packets. A Flow class is defined in terms of the… |
| 1.3.6.1.4.1.43.29.4.21.1.2.1 | Rowa3ComQosFlowClassEntry | not-accessible | mandatory | An entry describing a single flow class entity. |
| 1.3.6.1.4.1.43.29.4.21.1.2.1.1 | Columna3ComQosFlowClassIndex | read-only | mandatory | A unique value for each entry. Flow classses use id values between 1-399. |
| 1.3.6.1.4.1.43.29.4.21.1.2.1.2 | Columna3ComQosFlowClassFilterIndex | read-only | mandatory | The unique filter index associated with this class. Note that the maximum limit of 100 filters is the aggregate of all the filters defined in the system, not j… |
| 1.3.6.1.4.1.43.29.4.21.1.2.1.3 | Columna3ComQosFlowClassCastType | read-write | mandatory | The network layer cast type for this class. |
| 1.3.6.1.4.1.43.29.4.21.1.2.1.4 | Columna3ComQosFlowClassIpProtoType | read-write | mandatory | The IP protocol type for this class. |
| 1.3.6.1.4.1.43.29.4.21.1.2.1.5 | Columna3ComQosFlowClassSrcAddr | read-write | mandatory | The source IP address for this class. |
| 1.3.6.1.4.1.43.29.4.21.1.2.1.6 | Columna3ComQosFlowClassSrcSubnetMask | read-write | mandatory | The source subnet mask for this class. |
| 1.3.6.1.4.1.43.29.4.21.1.2.1.7 | Columna3ComQosFlowClassDestAddr | read-write | mandatory | The destination IP address for this class. |
| 1.3.6.1.4.1.43.29.4.21.1.2.1.8 | Columna3ComQosFlowClassDestSubnetMask | read-write | mandatory | The destination subnet mask for this class. |
| 1.3.6.1.4.1.43.29.4.21.1.2.1.9 | Columna3ComQosFlowClassPortStart | read-write | mandatory | The starting range of ports associated with this class. |
| 1.3.6.1.4.1.43.29.4.21.1.2.1.10 | Columna3ComQosFlowClassPortEnd | read-write | mandatory | The finishing range of ports associated with this class. |
| 1.3.6.1.4.1.43.29.4.21.1.2.1.11 | Columna3ComQosFlowClassRowStatus | read-write | mandatory | The status column for this entry. This object can be set to: createAndGo(4) destroy(6) The following value may be read: active(1) Setting this object to create… |
| 1.3.6.1.4.1.43.29.4.21.1.3 | Tablea3ComQosNonFlowClassTable | not-accessible | mandatory | This table lists the Non-Flow classes defined in the system. A Non-Flow class defines a packet in terms of its data link level protocol: IEEE 802.1p tag value,… |
| 1.3.6.1.4.1.43.29.4.21.1.3.1 | Rowa3ComQosNonFlowClassEntry | not-accessible | mandatory | An entry describing a single non-flow class entity. |
| 1.3.6.1.4.1.43.29.4.21.1.3.1.1 | Columna3ComQosNonFlowClassIndex | read-only | mandatory | A unique value for each entry. Non-flow classs use class ids values between 400-499. |
| 1.3.6.1.4.1.43.29.4.21.1.3.1.2 | Columna3ComQosNonFlowClassCastType | read-write | mandatory | A bit mask of 'cast' types associated with this class. Each cast is represented by a single bit. If that bit is set then the corresponding cast is selected by … |
| 1.3.6.1.4.1.43.29.4.21.1.3.1.3 | Columna3ComQosNonFlowClassProtos | read-write | mandatory | A bit mask of network protocols associated with this class. Each protocol is represented by a single bit. If that bit is set then the corresponding protocol is… |
| 1.3.6.1.4.1.43.29.4.21.1.3.1.4 | Columna3ComQosNonFlowClass8021pTags | read-write | mandatory | A bit mask of the 802.1p tags associated with this class. Each tag is represented by a single bit. If that bit is set then the corresponding tag is selected by… |
| 1.3.6.1.4.1.43.29.4.21.1.3.1.5 | Columna3ComQosNonFlowClassRowStatus | read-write | mandatory | The status column for this entry. This object can be set to: createAndGo(4) destroy(6) The following value may be read: active(1) Setting this object to create… |
| 1.3.6.1.4.1.43.29.4.21.1.3.1.6 | Columna3ComQosNonFlowClassProtoDescriptor | read-write | mandatory | This object determines whether a3ComQosNonFlowClassProtos or a3ComQosNonFlowClassCustomProto is used to define the protocol for a classifier. If set to name(1)… |
| 1.3.6.1.4.1.43.29.4.21.1.3.1.7 | Columna3ComQosNonFlowClassCustomProto | read-write | mandatory | This object determines a 2-byte hex value for the Ethertype or DSAP/SSAP that will be used in conjunction with a3ComQosNonFlowClassProtoDescriptor. If a3ComQos… |
| 1.3.6.1.4.1.43.29.4.21.2 | Nodea3ComQosCtrl | |||
| 1.3.6.1.4.1.43.29.4.21.2.1 | Tablea3ComQosCtrlTable | not-accessible | mandatory | A list of controls defined on a given system. |
| 1.3.6.1.4.1.43.29.4.21.2.1.1 | Rowa3ComQosCtrlEntry | not-accessible | mandatory | An entry describing a single QoS control. |
| 1.3.6.1.4.1.43.29.4.21.2.1.1.1 | Columna3ComQosCtrlIndex | read-only | mandatory | A unique value for this entry. |
| 1.3.6.1.4.1.43.29.4.21.2.1.1.2 | Columna3ComQosCtrlName | read-write | mandatory | A textual name for the control. |
| 1.3.6.1.4.1.43.29.4.21.2.1.1.3 | Columna3ComQosCtrlServiceLevel | read-write | mandatory | The service level for all conforming packets. |
| 1.3.6.1.4.1.43.29.4.21.2.1.1.4 | Columna3ComQosCtrlConformPktsLossEligible | read-write | mandatory | The variable indicates whether conforming packets are loss eligible. |
| 1.3.6.1.4.1.43.29.4.21.2.1.1.5 | Columna3ComQosCtrlExcessPktsServiceLevel | read-write | mandatory | The service level of excess packets for this control. |
| 1.3.6.1.4.1.43.29.4.21.2.1.1.6 | Columna3ComQosCtrlExcessPktsLossEligible | read-write | mandatory | The variable indicates whether excess packets are loss eligible. |
| 1.3.6.1.4.1.43.29.4.21.2.1.1.7 | Columna3ComQosCtrl8021pTag | read-write | mandatory | This indicates the tag to use on forwarded frames. |
| 1.3.6.1.4.1.43.29.4.21.2.1.1.8 | Columna3ComQosCtrlRateLimitType | read-write | mandatory | The rate limit type to use with this control. A value of none(1) indicates that no rate limit is set for this control. A value of receivePort(2) indicates that… |
| 1.3.6.1.4.1.43.29.4.21.2.1.1.9 | Columna3ComQosCtrlRowStatus | read-write | mandatory | The status column for this control entry. This object can be set to: createAndGo(4) destroy(6) The following value may be read: active(1) Setting this object t… |
| 1.3.6.1.4.1.43.29.4.21.2.2 | Tablea3ComQosCtrlRateLimitTable | not-accessible | mandatory | A list of QoS control rate limits defined on a given system. |
| 1.3.6.1.4.1.43.29.4.21.2.2.1 | Rowa3ComQosCtrlRateLimitEntry | not-accessible | mandatory | An entry describing a single QoS control rate limit. |
| 1.3.6.1.4.1.43.29.4.21.2.2.1.1 | Columna3ComQosCtrlRateLimitCtrlIndex | read-only | mandatory | The control index for which this entry is valid. |
| 1.3.6.1.4.1.43.29.4.21.2.2.1.2 | Columna3ComQosCtrlRateLimitIndex | read-only | mandatory | The rate limit for which this entry is valid. |
| 1.3.6.1.4.1.43.29.4.21.2.2.1.3 | Columna3ComQosCtrlRateLimitPercent | read-write | mandatory | The rate limit as a percentage of input port bandwidth. Packets received in excess of specified rate limit will receive the service defined by value of a3ComQo… |
| 1.3.6.1.4.1.43.29.4.21.2.2.1.4 | Columna3ComQosCtrlRateLimitKbps | read-write | mandatory | The rate limit in kilobits per second of input port bandwidth. Packets received in excess of specified rate limit will receive the service defined by value of … |
| 1.3.6.1.4.1.43.29.4.21.2.2.1.5 | Columna3ComQosCtrlRateLimitPorts | read-write | mandatory | A bit mask of interfaces that support the defined rate limit. Each interface is represented by a single bit. If that bit is set then the corresponding interfac… |
| 1.3.6.1.4.1.43.29.4.21.2.2.1.6 | Columna3ComQosCtrlRateLimitRowStatus | read-write | mandatory | The status column for this rate limit entry. This object can be set to: createAndGo(4) destroy(6) The following value may be read: active(1) Setting this objec… |
| 1.3.6.1.4.1.43.29.4.21.3 | Nodea3ComQosRsvp | |||
| 1.3.6.1.4.1.43.29.4.21.3.1 | Scalara3ComQosRsvpStatus | read-write | mandatory | The status of the RSVP protocol. |
| 1.3.6.1.4.1.43.29.4.21.3.2 | Scalara3ComQosRsvpMaxTotalResvdBandwidth | read-write | mandatory | The maximum total reservable bandwidth of the output link. |
| 1.3.6.1.4.1.43.29.4.21.3.3 | Scalara3ComQosRsvpMaxPerResvBandwidth | read-write | mandatory | The maximum per-reservation bandwidth of the output link. |
| 1.3.6.1.4.1.43.29.4.21.3.4 | Scalara3ComQosRsvpPolicy | read-write | mandatory | The indication of a policing option that shows when excess packets are dropped. |
| 1.3.6.1.4.1.43.29.4.21.3.5 | Scalara3ComQosRsvpExcessTrafficPolicy | read-write | mandatory | The indication of service for excess packets. |
| 1.3.6.1.4.1.43.29.4.21.3.6 | Scalara3ComQosRsvpExcessPktsLossEligible | read-write | mandatory | This object indicates if excess packets are loss eligible. |
| 1.3.6.1.4.1.43.29.4.21.3.7 | Scalara3ComQosRsvpAuthentication | read-write | mandatory | This object indicates the status of RSVP authentication. |
| 1.3.6.1.4.1.43.29.4.21.3.8 | Scalara3ComQosRsvpMd5Key | read-write | mandatory | The MD5 encryption key. This value is used if the a3ComQosRsvpAuthStatus object is set to enabled(1). |
| 1.3.6.1.4.1.43.29.4.21.4 | Nodea3ComQosStats | |||
| 1.3.6.1.4.1.43.29.4.21.4.1 | Scalara3ComQosStatsInterval | read-write | mandatory | The time interval, in seconds, over which rate statistics are collected. A value of zero implies absolute (i.e. raw) statistics. |
| 1.3.6.1.4.1.43.29.4.21.4.2 | Tablea3ComQosXmtStatsTable | not-accessible | mandatory | This table contains QoS transmit rate statistics. The interval over which the rate is calculated is determined by the value of a3ComQosStatsInterval object. |
| 1.3.6.1.4.1.43.29.4.21.4.2.1 | Rowa3ComQosXmtStatsEntry | not-accessible | mandatory | An entry containing transmit rate statistics. |
| 1.3.6.1.4.1.43.29.4.21.4.2.1.1 | Columna3ComQosXmtStatsQindex | read-only | mandatory | The type of transmit queue for which this entry is valid. |
| 1.3.6.1.4.1.43.29.4.21.4.2.1.2 | Columna3ComQosXmtStatsLowLossPkts | read-only | mandatory | The rate of low loss packets. Low loss packets are packets that are not marked as loss eligible (a3ComQosCtrlConformPktLossEligible object) and are under the t… |
| 1.3.6.1.4.1.43.29.4.21.4.2.1.3 | Columna3ComQosXmtStatsLowLossDelayedPkts | read-only | mandatory | The rate of low loss delayed packets. Low loss delayed packets are packets that are not marked as loss eligible (a3ComQosCtrlConformPktLossEligible object) and… |
| 1.3.6.1.4.1.43.29.4.21.4.2.1.4 | Columna3ComQosXmtStatsLowLossDiscardedPkts | read-only | mandatory | The rate of low loss discarded packets. Low loss discarded packets are packets that are discarded due to the queue being full. The rate is specified in packets… |
| 1.3.6.1.4.1.43.29.4.21.4.2.1.5 | Columna3ComQosXmtStatsHighLossPkts | read-only | mandatory | The rate of high loss packets. High loss packets are packets that are marked as loss eligible (a3ComQosCtrlConformPktLossEligible object) and are under the thr… |
| 1.3.6.1.4.1.43.29.4.21.4.2.1.6 | Columna3ComQosXmtStatsHighLossDiscardedPkts | read-only | mandatory | The rate of high loss discarded packets. High loss discarded packets are packets that are marked as loss eligible (a3ComQosCtrlConformPktLossEligible object) a… |
| 1.3.6.1.4.1.43.29.4.21.4.3 | Tablea3ComQosXmtHmStatsTable | not-accessible | mandatory | This table contains QoS transmit high water mark rate statistics. The interval over which the rate is calculated is determined by the value of a3ComQosStatsInt… |
| 1.3.6.1.4.1.43.29.4.21.4.3.1 | Rowa3ComQosXmtHmStatsEntry | not-accessible | mandatory | An entry containing transmit high water mark rate statistics. |
| 1.3.6.1.4.1.43.29.4.21.4.3.1.1 | Columna3ComQosXmtHmStatsQindex | read-only | mandatory | The type of queue for which this entry is valid. |
| 1.3.6.1.4.1.43.29.4.21.4.3.1.2 | Columna3ComQosXmtHmStatsLowLossPkts | read-only | mandatory | The high mark for low loss packets. |
| 1.3.6.1.4.1.43.29.4.21.4.3.1.3 | Columna3ComQosXmtHmStatsLowLossDelayedPkts | read-only | mandatory | The high mark for low loss delayed packets. |
| 1.3.6.1.4.1.43.29.4.21.4.3.1.4 | Columna3ComQosXmtHmStatsLowLossDiscardedPkts | read-only | mandatory | The high mark for low loss discarded packets. |
| 1.3.6.1.4.1.43.29.4.21.4.3.1.5 | Columna3ComQosXmtHmStatsHighLossPkts | read-only | mandatory | The high mark for high loss packets. |
| 1.3.6.1.4.1.43.29.4.21.4.3.1.6 | Columna3ComQosXmtHmStatsHighLossDiscardedPkts | read-only | mandatory | The high mark for high loss discarded packets. |
| 1.3.6.1.4.1.43.29.4.21.4.4 | Tablea3ComQosRcvStatsTable | not-accessible | mandatory | A table containing QoS receive rate statistics. The interval over which the rate is calculated is determined by the value of a3ComQosStatsInterval object. |
| 1.3.6.1.4.1.43.29.4.21.4.4.1 | Rowa3ComQosRcvStatsEntry | not-accessible | mandatory | An entry containing receive rate statistics for a particular port. |
| 1.3.6.1.4.1.43.29.4.21.4.4.1.1 | Columna3ComQosRcvStatsConformBytesTotal | read-only | mandatory | The total conforming bytes receive rate. The rate is in bytes per second. |
| 1.3.6.1.4.1.43.29.4.21.4.4.1.2 | Columna3ComQosRcvStatsNonConformBytesForFlows | read-only | mandatory | The non-conforming bytes receive rate for flows. The rate is in bytes per second. |
| 1.3.6.1.4.1.43.29.4.21.4.4.1.3 | Columna3ComQosRcvStatsNonConformBytesForNonFlows | read-only | mandatory | The non-conforming bytes receive rate for non-flows. The rate is in bytes per second. |
| 1.3.6.1.4.1.43.29.4.21.4.4.1.4 | Columna3ComQosRcvStatsDroppedPkts | read-only | mandatory | The number of packets dropped. The rate is specified in packets per second. |
| 1.3.6.1.4.1.43.29.4.21.5 | Nodea3ComQosMisc | |||
| 1.3.6.1.4.1.43.29.4.21.5.1 | Scalara3ComQosBandwidthRatio | read-write | mandatory | The bandwidth ratio of HighPriority/(HighPriority+BestEffort) that is allocated for each output port on a given system. The value is represented as a percentag… |
| 1.3.6.1.4.1.43.29.4.21.5.2 | Scalara3ComQosExcessTrafficClassTag | read-write | mandatory | This object indicates the IEEE802.1p traffic class value to use to retag excess packets. |
| 1.3.6.1.4.1.43.29.4.88 | Nodea3ComQosFlowClassIntrudingEvent | The trap that is generated when a intruder tries to enter a classified network |