A3COM0420-SWITCH-EXTENSIONS
45 objects
No module-level DESCRIPTION found.
Imported Objects
| A3COM0004-GENERIC | brasica2 |
| RFC-1212 | OBJECT-TYPE |
| RFC1213-MIB | ifIndex |
| SNMPv2-TC | MacAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.43.10.34.1 | NodestackConfigGroup | |||
| 1.3.6.1.4.1.43.10.34.1.1 | ScalarprConStackFwdingMode | read-write | mandatory | This object controls whether cut-thru is enabled on the stack. Enabling cut-through can help to minimise the delay experienced by packets before they are forwa… |
| 1.3.6.1.4.1.43.10.34.1.2 | ScalarprConStackPaceMode | read-write | mandatory | This object specifies the type of backoff algorithm used on the units in the stack. Any suitable port can use the standard ethernet algorithm or, for PACE appl… |
| 1.3.6.1.4.1.43.10.34.1.3 | ScalarprConStackVLANConfigMode | read-write | mandatory | This object specifies the VLAN mode to be used. Setting it to portMode(2) requires the user to configure each port's VLAN membership individually, whereas auto… |
| 1.3.6.1.4.1.43.10.34.1.4 | ScalarprConStackRAPStudyPort | read-write | mandatory | This determines the ifIndex of the port a user wishes to monitor on the copy port. Monitoring causes all data from the study port to be copied to the copy port… |
| 1.3.6.1.4.1.43.10.34.1.5 | ScalarprConStackRAPCopyPort | read-write | mandatory | This is the value of ifIndex specifying the port to which data will be copied (mirrored), and must be set to a valid value, along with the study port, before m… |
| 1.3.6.1.4.1.43.10.34.1.6 | ScalarprConStackRAPEnable | read-write | mandatory | This object controls the Roving Analysis Port (RAP) feature in conjunction with prConStackRAPStudyPort and prConStackRAPCopyPort. The RAP feature allows all fr… |
| 1.3.6.1.4.1.43.10.34.1.7 | ScalarprConStackBridgeMode | read-write | mandatory | The value of this object determines whether the switch is to operate as a single bridge or as a bridge per VLAN (the default). In multiple bridge mode the swit… |
| 1.3.6.1.4.1.43.10.34.1.9 | ScalarprConStackIpTos | read-write | mandatory | This object is used to enable the classification of packets based upon the value of their IPToS field. When enabled, the packet's Traffic Classification will b… |
| 1.3.6.1.4.1.43.10.34.1.10 | ScalarprConStackPktRateControl | read-write | mandatory | This object controls whether the packet rate control feature is enabled or disabled. Products which do not support this feature will return notApplicable(1) an… |
| 1.3.6.1.4.1.43.10.34.1.11 | ScalarprConStackPktRateLimit | read-write | mandatory | This object specifies the maximum rate at which the selected types of packet may be received from a port before excess packets are discarded. The limit is spec… |
| 1.3.6.1.4.1.43.10.34.1.12 | ScalarprConStackStpProtocolVersion | read-write | mandatory | The version of the Spanning Tree Protocol that is to be used by this Bridge. stpVersion0(0) The original version of Spanning Tree, defined by IEEE Std. 802.1D-… |
| 1.3.6.1.4.1.43.10.34.1.13 | ScalarprConStackStpPathCostDefault | read-write | mandatory | The version of the Spanning Tree default Path Costs that are to be used by this Bridge. stp8021d1998(1) Path Costs from IEEE Std. 802.1D-1998. stp8021t2000(2) … |
| 1.3.6.1.4.1.43.10.34.1.14 | ScalarprConStackLacpOperInfo | read-only | mandatory | This object shall contain a value indicating that LACP is operational, or not operational. If not operational, all units need to be upgraded to the latest agen… |
| 1.3.6.1.4.1.43.10.34.2 | NodeswitchConfigGroup | |||
| 1.3.6.1.4.1.43.10.34.2.1 | TableprConfigPortTable | not-accessible | mandatory | Table providing configuration information about a port on a Switch unit. |
| 1.3.6.1.4.1.43.10.34.2.1.1 | RowprConfigPortEntry | not-accessible | mandatory | Configuration options for a single port. |
| 1.3.6.1.4.1.43.10.34.2.1.1.1 | ColumnprConPortVLANConfigMode | read-write | mandatory | This object specifies the VLAN mode to be used. Setting it to portMode(3) requires the user to configure the port's VLAN membership explicitly, whereas autoSel… |
| 1.3.6.1.4.1.43.10.34.2.1.1.13 | ColumnprConPortIFM | read-write | mandatory | This object controls Intelligent Flow Management for the port, which specifies what action the port takes whenever it is unable to receive a packet because its… |
| 1.3.6.1.4.1.43.10.34.2.1.1.14 | ColumnprConPortLacp | read-write | mandatory | This object specifies whether a port will use LACP. When enabled LACP will be active on the port. When disabled LACP will cease this may cause a port to be tak… |
| 1.3.6.1.4.1.43.10.34.2.1.1.15 | ColumnprConPortStpAdminPathCost | read-write | mandatory | The administratively assigned value of the path cost for this port. The contribution of this port to the path cost of paths towards the spanning tree root whic… |
| 1.3.6.1.4.1.43.10.34.2.1.1.16 | ColumnprConPortCascadeMode | read-only | mandatory | This object specifies whether the port is a cascade port or not. If enabled, the port is operating as a cascade port. If disabled, the port is not operating as… |
| 1.3.6.1.4.1.43.10.34.2.2 | TableprConPortFdbTable | not-accessible | mandatory | This table provides the same information as that held in the dot1qTpFdbTable in the Bridge Extension MIB. |
| 1.3.6.1.4.1.43.10.34.2.2.1 | RowprConPortFdbEntry | not-accessible | mandatory | Information about a specific unicast MAC address. |
| 1.3.6.1.4.1.43.10.34.2.2.1.1 | ColumnprConPortFdbPort | not-accessible | mandatory | This contains the port number that this address has been seen on. It is similar to dot1qTpFdbPort in the Bridge Extensions MIB but may not be the value zero. |
| 1.3.6.1.4.1.43.10.34.2.2.1.2 | ColumnprConPortFdbId | not-accessible | mandatory | The identity of this filtering database. This shall have the same value as is defined for dot1qFdbId in the bridge MIB extensions MIB. |
| 1.3.6.1.4.1.43.10.34.2.2.1.3 | ColumnprConPortFdbAddress | not-accessible | mandatory | This object contains the unicast MAC address of the entry. This contains the same value as dot1qTpFdbAddress in the Bridge Extensions MIB. |
| 1.3.6.1.4.1.43.10.34.2.2.1.4 | ColumnprConPortFdbStatus | read-only | mandatory | This contains the same information as dot1qTpFdbStatus in the Bridge Extensions MIB. |
| 1.3.6.1.4.1.43.10.34.2.3 | TableprConTrunkMulticastTable | not-accessible | mandatory | Table for distributing multicast addresses on trunks across a stack. |
| 1.3.6.1.4.1.43.10.34.2.3.1 | RowprConTrunkMulticastEntry | not-accessible | mandatory | Information associated with a single multicast entry. |
| 1.3.6.1.4.1.43.10.34.2.3.1.1 | ColumnprConTrunkMulticastFdbId | not-accessible | mandatory | The identity of the filtering database. This contains the same value as dot1qFdbId in the Bridge Extensions MIB. |
| 1.3.6.1.4.1.43.10.34.2.3.1.2 | ColumnprConTrunkMulticastAddress | not-accessible | mandatory | This object contains the multicast MAC address of the entry. This contains the same value as the dot1qTpGroupAddress in the Bridge Extensions MIB |
| 1.3.6.1.4.1.43.10.34.2.3.1.3 | ColumnprConTrunkMulticastPortlist | read-write | mandatory | The set of trunk ports to which frames destined for this multicast address should be forwarded. Each octet within the value of this object specifies a set or e… |
| 1.3.6.1.4.1.43.10.34.2.3.1.4 | ColumnprConTrunkMulticastStatus | read-write | mandatory | This object specifies the status of the entry. The default value is other(1). This object contains the same information as dot1dStaticStatus in RFC1493. |
| 1.3.6.1.4.1.43.10.34.2.3.1.5 | ColumnprConTrunkMulticastType | read-write | mandatory | This object contains the same information as dot1qTpFdbStatus in the Bridge Extensions MIB. |
| 1.3.6.1.4.1.43.10.34.2.3.1.6 | ColumnprConTrunkMulticastRobp | read-only | mandatory | This object contains the Receive on Blocked port setting. |
| 1.3.6.1.4.1.43.10.34.2.4 | TableprConIfIndexTable | not-accessible | mandatory | Table for translating between unit.port and ifIndex or bridge port number. |
| 1.3.6.1.4.1.43.10.34.2.4.1 | RowprConIfIndexEntry | not-accessible | mandatory | The IfIndex and bridge port number associated with a port entry. |
| 1.3.6.1.4.1.43.10.34.2.4.1.1 | ColumnprConIfIndexGroupIndex | not-accessible | mandatory | This object identifies the group, unit or blade containing the port for which this entry contains information. |
| 1.3.6.1.4.1.43.10.34.2.4.1.2 | ColumnprConIfIndexPortIndex | not-accessible | mandatory | This object identifies the port within the group for which this entry contains information. |
| 1.3.6.1.4.1.43.10.34.2.4.1.3 | ColumnprConIfIndex | read-only | mandatory | This object contains the corresponding ifIndex value. |
| 1.3.6.1.4.1.43.10.34.2.4.1.4 | ColumnprConIfIndexBridgePort | read-only | mandatory | The corresponding bridge port number, which is the number of the port as defined by RFC1493. If a port is a member of an aggregation, the value will be that of… |
| 1.3.6.1.4.1.43.10.34.2.5 | TableprConfigAggTable | not-accessible | mandatory | Table providing configuration information about an aggregation on a Switch unit. |
| 1.3.6.1.4.1.43.10.34.2.5.1 | RowprConfigAggEntry | not-accessible | mandatory | Configuration information for a single aggregation. |
| 1.3.6.1.4.1.43.10.34.2.5.1.1 | ColumnprConfigAggStatus | read-only | mandatory | This object specifies the aggregation status. The status is indicated as follows: unused(1) the aggregation is not presently in use. autoInUse(2) the aggregati… |