A3Com-PortPath-r6-MIB
116 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises TimeTicks |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.43 | Nodea3Com | |||
| 1.3.6.1.4.1.43.2 | NodebrouterMIB | |||
| 1.3.6.1.4.1.43.2.16 | Nodea3ComPath | |||
| 1.3.6.1.4.1.43.2.16.1 | Scalara3ComPathNumber | read-only | mandatory | The number of entries in the Path Table. These correspond to physical interfaces in a 3Com product. Note, any changes made to any entry in this table will affe… |
| 1.3.6.1.4.1.43.2.16.2 | Tablea3ComPathTable | not-accessible | mandatory | A table of physical interfaces. |
| 1.3.6.1.4.1.43.2.16.2.1 | Rowa3ComPathEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.43.2.16.2.1.1 | Columna3ComPathIndex | read-only | mandatory | A unique identifier for each path. The value for each path must remain constant at least from one re-initialization of the entity's network management system t… |
| 1.3.6.1.4.1.43.2.16.2.1.2 | Columna3ComPathName | read-write | mandatory | A descriptive name for the path |
| 1.3.6.1.4.1.43.2.16.2.1.3 | Columna3ComPathPort | read-write | mandatory | The index of the entry in the Port table to which this path entry has been assigned. Unassigned entries have a value of zero. This object allows adding and del… |
| 1.3.6.1.4.1.43.2.16.2.1.4 | Columna3ComPathItcmOption | read-write | mandatory | This object should be set to compatible if the bridge/router is attached via a serial link to a 3Com Series/1 based bridge or bridge/router (IB/3, BR/3) that c… |
| 1.3.6.1.4.1.43.2.16.2.1.5 | Columna3ComPathT1Mode | read-write | mandatory | Enabling this object allows for better line speed than if this were disabled. However, do not enable this object when a3ComPathItcmOpt is set to compatible. |
| 1.3.6.1.4.1.43.2.16.2.1.6 | Columna3ComPathCryptoResync | read-write | mandatory | Enabling this parameter causes the router to resynch with any attached KG84/91 devices. This only applies to the 449 interface of a wide area bridge/router. |
| 1.3.6.1.4.1.43.2.16.2.1.7 | Columna3ComPathCRC | read-write | mandatory | This controls the type of Cyclic Redundancy Check that is performed on a serial line. In order for any modifications to take effect, the path must be enabled(r… |
| 1.3.6.1.4.1.43.2.16.2.1.8 | Columna3ComPathAdminStatus | read-write | mandatory | This object enables or disables a path. |
| 1.3.6.1.4.1.43.2.16.2.1.9 | Columna3ComPathOperStatus | read-only | mandatory | The actual state of the path. |
| 1.3.6.1.4.1.43.2.16.2.1.10 | Columna3ComPathBaud | read-write | deprecated | The baud rate for serial paths. For ethernet, token ring, or FDDI connections this has a value notApplicable(1). In order for any modifications to take effect,… |
| 1.3.6.1.4.1.43.2.16.2.1.11 | Columna3ComPathConn | read-write | mandatory | The connector for the path. For ethernet, token ring, or FDDI connections this has a value notApplicable(1). In order for any modifications to take effect, the… |
| 1.3.6.1.4.1.43.2.16.2.1.12 | Columna3ComPathClock | read-write | mandatory | How the transmit clock is derived. For ethernet, token ring, or FDDI connections this has a value notApplicable(1). In order for any modifications to take effe… |
| 1.3.6.1.4.1.43.2.16.2.1.13 | Columna3ComPathLastChange | read-only | mandatory | The value of sysUpTime at the time the path entered its current operational state. |
| 1.3.6.1.4.1.43.2.16.2.1.14 | Columna3ComPathSlotIndex | read-only | mandatory | The index number of the chassis slot into which the module (or board) that supports this Path is inserted. |
| 1.3.6.1.4.1.43.2.16.2.1.15 | Columna3ComPathConnPos | read-only | mandatory | The relative position on the module (or board) of the physical connector that supports this path. The position is identified by an index, which starts at one w… |
| 1.3.6.1.4.1.43.2.16.2.1.16 | Columna3ComPathInOctets | read-only | mandatory | The total number of octets received on the path, including framing characters. |
| 1.3.6.1.4.1.43.2.16.2.1.17 | Columna3ComPathInUcastPkts | read-only | mandatory | The number of subnetwork-unicast packets delivered to a higher-layer protocol. |
| 1.3.6.1.4.1.43.2.16.2.1.18 | Columna3ComPathInNUcastPkts | read-only | mandatory | The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol. |
| 1.3.6.1.4.1.43.2.16.2.1.19 | Columna3ComPathInDiscards | read-only | mandatory | The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer pr… |
| 1.3.6.1.4.1.43.2.16.2.1.20 | Columna3ComPathInErrors | read-only | mandatory | The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. |
| 1.3.6.1.4.1.43.2.16.2.1.21 | Columna3ComPathInUnknownProtos | read-only | mandatory | The number of packets received via the path which were discarded because of an unknown or unsupported protocol. |
| 1.3.6.1.4.1.43.2.16.2.1.22 | Columna3ComPathOutOctets | read-only | mandatory | The total number of octets transmitted out of the path, including framing characters. |
| 1.3.6.1.4.1.43.2.16.2.1.23 | Columna3ComPathOutUcastPkts | read-only | mandatory | The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not se… |
| 1.3.6.1.4.1.43.2.16.2.1.24 | Columna3ComPathOutNUcastPkts | read-only | mandatory | The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) addre… |
| 1.3.6.1.4.1.43.2.16.2.1.25 | Columna3ComPathOutDiscards | read-only | mandatory | The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reaso… |
| 1.3.6.1.4.1.43.2.16.2.1.26 | Columna3ComPathOutErrors | read-only | mandatory | The number of outbound packets that could not be transmitted because of errors. |
| 1.3.6.1.4.1.43.2.16.2.1.27 | Columna3ComPathBaudRate | read-write | mandatory | The baud rate for serial paths. For ethernet, token ring, or FDDI connections this reports the actual value, but SETs are not allowed for those Paths. In order… |
| 1.3.6.1.4.1.43.2.16.2.1.28 | Columna3ComPathDuplex | read-write | mandatory | The duplex mode is for SDLC and V3. It describes the physical characteristics of the communication method used to control the request-to-send signal. It has th… |
| 1.3.6.1.4.1.43.2.17 | Nodea3ComPort | |||
| 1.3.6.1.4.1.43.2.17.1 | Scalara3ComPortNumber | read-only | mandatory | The number of entries in the Port Table. These correspond to attached or remotely connected network segments. |
| 1.3.6.1.4.1.43.2.17.2 | Tablea3ComPortTable | not-accessible | mandatory | A table of attached or remotely connect network segments. |
| 1.3.6.1.4.1.43.2.17.2.1 | Rowa3ComPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.43.2.17.2.1.1 | Columna3ComPortIndex | read-only | mandatory | A unique value for each port. This corresponds to ifIndex for MIB II. The interface table from MIB II will contain additional information for this port, includ… |
| 1.3.6.1.4.1.43.2.17.2.1.2 | Columna3ComPortOwner | read-write | mandatory | This object indicates the owner for this port. User can set the owner using this object, however, if the owner does not match the actual physical interface car… |
| 1.3.6.1.4.1.43.2.17.2.1.3 | Columna3ComPortBoundaryRoute | read-write | mandatory | This object controls whether the Boundary Routing feature is enabled for this port. Note: this feature only applies to serial ports on a NB2 and will be disabl… |
| 1.3.6.1.4.1.43.2.17.2.1.4 | Columna3ComPortBoundaryEncap | read-write | mandatory | This object decides the packet encapsulation rules to be applied to outgoing packets. If this is set to none (5), the boundary router on the other end of the s… |
| 1.3.6.1.4.1.43.2.17.2.1.5 | Columna3ComPortCosInterleave | read-write | deprecated | (For bridging.) The number of high-priority packets that will be transmitted for each low-priority packet. If the value is 0, then low-priority packets will on… |
| 1.3.6.1.4.1.43.2.17.2.1.6 | Columna3ComPortMacAddrFmtARP | read-write | mandatory | This object indicates the MAC address format used in ARP packets sent by this port. Note, nonCanonical(2) is allowed only on Token Ring ports. |
| 1.3.6.1.4.1.43.2.17.2.1.7 | Columna3ComPortMacAddrFmtIPX | read-write | mandatory | This determine the MAC address format used in IPX packets sent by this port. Note, nonCanonical(2) is allowed only on Token Ring ports. |
| 1.3.6.1.4.1.43.2.17.2.1.8 | Columna3ComPortMacAddrFmtXNS | read-write | mandatory | This determines the MAC address format used in XNS packets sent by this port. Note, nonCanonical(2) is allowed only on Token Ring ports. |
| 1.3.6.1.4.1.43.2.17.2.1.9 | Columna3ComPortPath | read-write | mandatory | The Path which is assigned to this port. In some cases, one or more Paths will be assigned to a single Port. This object will return the lowest number Path in … |
| 1.3.6.1.4.1.43.2.17.2.1.10 | Columna3ComQueueInterleave1 | read-write | mandatory | This object specifies the interleave factor between the high and medium priority port queues. Note, this applies only to HSS ports. For non-HSS ports, this obj… |
| 1.3.6.1.4.1.43.2.17.2.1.11 | Columna3ComQueueInterleave2 | read-write | mandatory | This object specifies the interleave factor between the medium and low priority port queues. Note, this applies only to HSS ports. For non-HSS ports, this obje… |
| 1.3.6.1.4.1.43.2.17.2.1.13 | Columna3ComQueuePattern | read-only | mandatory | This identifies the relative ratios of high priority packets versus medium priority packets versus low priority packets (in that order) that will be transmitte… |
| 1.3.6.1.4.1.43.2.17.2.1.15 | Columna3ComPortAsOwnerTimer | read-only | mandatory | This object only applies to High Speed Serial ports. When the Owner of this port has been set to Auto, the system will also automatically determine the proper … |
| 1.3.6.1.4.1.43.2.17.2.1.16 | Columna3ComSmartFilteringCtl | read-write | mandatory | This object is used to enable or disable the Smart Filtering mechanism on a port. Note, this only applies to the Central Node in a boundary routing environment… |
| 1.3.6.1.4.1.43.2.17.2.1.17 | Columna3ComBrCentralMacCtl | read-write | mandatory | This object is used to enable or disable the Boundary Routing Central MAC feature. If this feature is enabled, (ie, if this object has the value centralMac(1))… |
| 1.3.6.1.4.1.43.2.17.2.1.18 | Columna3ComPortLabel | read-only | mandatory | This object specifies the descriptive label assigned to this port by the router. These labels are used by the User Interface and are useful when comparing info… |
| 1.3.6.1.4.1.43.2.17.2.1.19 | Columna3ComPortCircuitID | read-write | mandatory | This object applies only to virtual ports and specifies the unique data link circuit or channel identifier assigned to this virtual port. For example, if this … |
| 1.3.6.1.4.1.43.2.17.2.1.20 | Columna3ComPortStatus | read-write | mandatory | This object is used to add or delete virtual ports. When adding a new virtual port, only the createAndGo method of adding rows is supported. Specifically, all … |
| 1.3.6.1.4.1.43.2.17.2.1.21 | Columna3ComPortName | read-write | mandatory | The user-assigned name given to this port. Note, this name may not have any blanks. |
| 1.3.6.1.4.1.43.2.17.2.1.22 | Columna3ComPortVirtual | read-only | mandatory | This object indicates whether this port is a virtual port or a normal port. |
| 1.3.6.1.4.1.43.2.17.2.1.23 | Columna3ComQueueThrottle | read-write | mandatory | This object specifies the maximum number of medium and low priority packets that can be sent to the line driver each time some packets are sent to the driver. … |
| 1.3.6.1.4.1.43.2.17.2.1.24 | Columna3ComPortInCallerId | read-write | mandatory | A text string to specify the effective Incoming CallerID for the port. This object must be successfully set for a port to use the dynamic dial pool. It is used… |
| 1.3.6.1.4.1.43.2.17.2.1.25 | Columna3ComPortCompType | read-write | mandatory | This object specifies the type of compression performed on this Port. NONE indicates that the compression is disabled. HIStory indicates that the compression i… |
| 1.3.6.1.4.1.43.2.17.2.1.26 | Columna3ComPortX25ProtID | read-write | mandatory | This object specifies the X25 ProtolID used when running in Boundary Routed Mode for establishing the Virtual Circuits over X25 Link. |
| 1.3.6.1.4.1.43.2.17.2.1.27 | Columna3ComPortIbmTraffic | read-write | mandatory | This object is used to enable or disable the SmartFiltering of IBM Traffic mechanism on a port. Note, this only applies to the Central Node in a boundary routi… |
| 1.3.6.1.4.1.43.2.17.3 | Scalara3ComDefaultPriority | read-write | mandatory | This object specifies the default priority queue into which a packet with no preassigned priority is placed. Note, the system retains only a single instance of… |
| 1.3.6.1.4.1.43.2.18 | Nodea3ComPathDial | |||
| 1.3.6.1.4.1.43.2.18.1 | Scalara3ComPathDialNumber | read-only | mandatory | The number of entries in the Path Dial Table. These correspond to physical interfaces in a 3Com product. |
| 1.3.6.1.4.1.43.2.18.2 | Tablea3ComPathDialTable | not-accessible | mandatory | A table of physical interfaces. |
| 1.3.6.1.4.1.43.2.18.2.1 | Rowa3ComPathDialEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.43.2.18.2.1.1 | Columna3ComPathDialIndex | read-only | mandatory | A unique identifier for each path. The value for each path must remain constant at least from one re-initialization of the entity's network management system t… |
| 1.3.6.1.4.1.43.2.18.2.1.2 | Columna3ComPathDialType | read-write | mandatory | When assigning multiple paths for a single port, and one or more of those paths is a dial-up Path, this object must identify which Path is the primary Path and… |
| 1.3.6.1.4.1.43.2.18.2.1.3 | Columna3ComPathDialCtl | read-write | mandatory | For those Paths for which the value of a3ComPathDialType is primaryDial(2) or secondaryDial(3), this object is used to control whether that Path may originate … |
| 1.3.6.1.4.1.43.2.18.2.1.4 | Columna3ComPathDialAction | read-write | mandatory | This object is used to initiate an action to be taken by the primary dial-up Path. If this is set to dial(1), then the Path is brought up using the number stor… |
| 1.3.6.1.4.1.43.2.18.2.1.5 | Columna3ComPathDialNum | read-write | mandatory | This object contains the telephone number of the remote sit to be dialed. This is used whenever a dial-up Path is brought up. Spaces and hyphens (-) are allowe… |
| 1.3.6.1.4.1.43.2.18.2.1.6 | Columna3ComPathDialDodIdleTime | read-write | deprecated | This object applies only to a path that is setup as a PrimaryDial path in DialOnDemand mode. It defines the amount of time, in seconds, to wait after detecting… |
| 1.3.6.1.4.1.43.2.18.2.1.7 | Columna3ComPathDialMode | read-write | mandatory | This object is used for setting/reading the Dial Mode of a dialup path. Only values (1) and (2) can be set to the object: If the object is (1), the dialup path… |
| 1.3.6.1.4.1.43.2.18.2.1.8 | Columna3ComPathDialDynCont | read-write | mandatory | This object is used to specify whether the dialup path is of type static(1) or dynamic(3). If a path is made dynamic, it will automatically be assigned(added) … |
| 1.3.6.1.4.1.43.2.18.2.1.9 | Columna3ComPathDialLocalDialNumber | read-write | mandatory | The telephone number assigned to the local ISDN unit. This number and the local subaddress number, if present, are used primarily to determine if the unit shou… |
| 1.3.6.1.4.1.43.2.18.2.1.10 | Columna3ComPathDialLocalSubAddress | read-write | mandatory | The subaddress number assigned to the local ISDN unit. If the local dial number criterion passes, then the local subaddress number, if present, is the next cri… |
| 1.3.6.1.4.1.43.2.18.2.1.11 | Columna3ComPathDialSPIDDN1 | read-write | mandatory | The Service Profile Identification number assigned by a North American ISDN switch provider to identify the service profile of a ISDN unit. Valid characters ar… |
| 1.3.6.1.4.1.43.2.18.2.1.12 | Columna3ComPathDialSPIDDN2 | read-write | mandatory | The second Service Profile Identification number assigned by a North American ISDN switch provider to identify the service profile of a ISDN unit. Valid charac… |
| 1.3.6.1.4.1.43.2.18.2.1.13 | Columna3ComPathDialRateAdaption | read-write | mandatory | Specifies the data rate to be used on the ISDN B channel. Rate64 and Rate56 specify that the channel be connected at 64K or 56K, respectively. The connection a… |
| 1.3.6.1.4.1.43.2.18.2.1.14 | Columna3ComPathDialSwitchType | read-write | mandatory | Specifies the ISDN switch type the unit is connected to. The path has to be enabled for the new setting to take effect. |
| 1.3.6.1.4.1.43.2.18.2.1.15 | Columna3ComPathDialExDevType | read-write | mandatory | This object describes the external device type that is connected to the serial-line type (eg, HSS, HDWAN) path. It is applicable only for a dialup path. Use br… |
| 1.3.6.1.4.1.43.2.19 | Nodea3ComPortDial | |||
| 1.3.6.1.4.1.43.2.19.1 | Scalara3ComPortDIALNumber | read-only | mandatory | The number of entries in the Port DIAL Table. These correspond to attached or remotely connected network segments. |
| 1.3.6.1.4.1.43.2.19.2 | Tablea3ComPortDialTable | not-accessible | mandatory | A table of attached or remotely connect network segments. |
| 1.3.6.1.4.1.43.2.19.2.1 | Rowa3ComPortDialEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.43.2.19.2.1.1 | Columna3ComPortDialIndex | read-only | mandatory | A unique value for each port. This corresponds to ifIndex for MIB II. The interface table from MIB II will contain additional information for this port, includ… |
| 1.3.6.1.4.1.43.2.19.2.1.2 | Columna3ComPortDialDisasterCtl | read-write | mandatory | This object applies only to those Ports to which multiple Paths are assigned, at least one of which is a dial-up Path. If this is set to disasterRecovery(1), t… |
| 1.3.6.1.4.1.43.2.19.2.1.3 | Columna3ComPortDialBandOnDmnd | read-write | mandatory | This object applies only to those Ports to which multiple Paths are assigned, at least one of which is a dial-up Path. If this is set to bandwidthOnDemand(1), … |
| 1.3.6.1.4.1.43.2.19.2.1.4 | Columna3ComPortDialDebounceTimeUp | read-write | mandatory | This object defines the amount of time, in seconds, to wait after the primary Path has gone down before bringing the secondary dial-up Path up. If the primary … |
| 1.3.6.1.4.1.43.2.19.2.1.5 | Columna3ComPortDialDebounceTimeDown | read-write | mandatory | This object defines the amount of time, in seconds, to wait after the primary Path has come up before bringing the secondary, dial-up, Path down. If the primar… |
| 1.3.6.1.4.1.43.2.19.2.1.6 | Columna3ComPortDialInitState | read-write | mandatory | This object applies only to Ports which have paths setup as PrimaryDial paths. It is used to configure the PrimaryDial path as a dial initiator operating in on… |
| 1.3.6.1.4.1.43.2.19.2.1.7 | Columna3ComPortDialRcvrState | read-write | mandatory | This object applies only to Ports which have paths setup as PrimaryDial paths. It is used to configure the PrimaryDial path as a dial receiver operating in one… |
| 1.3.6.1.4.1.43.2.19.2.1.8 | Columna3ComPortDialAction | read-write | mandatory | This object is used to initiate manual dial or hangup action to be taken by the dialup port. If this is set to dial(1), the port will attempt to dial out on it… |
| 1.3.6.1.4.1.43.2.19.2.1.9 | Columna3ComPortDialDodIdleTime | read-write | mandatory | This object applies only to a port that is setup as a dial initiator in DialOnDemand mode. It defines the amount of time, in seconds, to wait after detecting t… |
| 1.3.6.1.4.1.43.2.19.2.1.10 | Columna3ComPortDialIdleTime | read-write | mandatory | This object applies only to a port that is setup as a dial initiator in ManualDial mode. It defines the amount of time, in seconds, to wait after detecting the… |
| 1.3.6.1.4.1.43.2.19.2.1.11 | Columna3ComPortDialDodCallsMade | read-only | mandatory | The cumulative total number of outgoing calls successfully initiated by the port operating in DialOnDemand mode. |
| 1.3.6.1.4.1.43.2.19.2.1.12 | Columna3ComPortDialDodCallsFail | read-only | mandatory | The cumulative total number of outgoing calls unsuccessfully initiated by the port operating in DialOnDemand mode. |
| 1.3.6.1.4.1.43.2.19.2.1.13 | Columna3ComPortDialDodUpTime | read-only | mandatory | The cumulative length of time in seconds that the Primary path of a port operating in DialOnDemand mode is Up. |
| 1.3.6.1.4.1.43.2.19.2.1.14 | Columna3ComPortDialDodPktsOut | read-only | mandatory | The cumulative total number of user-data packets sent out by the port operating in DialOnDemand mode. |
| 1.3.6.1.4.1.43.2.19.2.1.15 | Columna3ComPortDialBODTHreshold | read-write | mandatory | %BODTHreshold% This object specifies the level of sensitivity to bring up a BOD path for a port. The larger BODTHreshold value, the less sensitive to bring up … |
| 1.3.6.1.4.1.43.2.19.3 | Tablea3ComPortDialPoolPrefTable | not-accessible | mandatory | A table representing the PoolPreference lists for dynamic dialup ports. A PoolPreference list is a prioritized list of dynamic dial paths that a port can use, … |
| 1.3.6.1.4.1.43.2.19.3.1 | Rowa3ComPortDialPoolPrefEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.43.2.19.3.1.1 | Columna3ComPortDialPoolPrefPort | read-only | mandatory | Specifies the port number(portid), used as an index together with a3ComPortDialPoolPrefPathPos, to select a particular row entry. |
| 1.3.6.1.4.1.43.2.19.3.1.2 | Columna3ComPortDialPoolPrefPathPos | read-only | mandatory | Specifies the position(priority) in the PoolPreference list of a path, for the port. Used as an index together with a3ComPortDialPoolPrefPort to select a parti… |
| 1.3.6.1.4.1.43.2.19.3.1.3 | Columna3ComPortDialPoolPrefPathNum | read-write | mandatory | Specifies the path number(pathid) of a dynamic dial path that will be taken out from the dynamic dial pool and added into the PoolPreference list for the port. |
| 1.3.6.1.4.1.43.2.19.3.1.4 | Columna3ComPortDialPoolPrefStatus | read-write | mandatory | This object is used to add or delete a dynamic dial path in the PoolPreference list of a port. Each path and its position in the list is represented as a row. … |
| 1.3.6.1.4.1.43.2.19.4 | Tablea3ComPortDialPhoneListTable | not-accessible | mandatory | A table representing the PhoneNo lists for dialup ports. Setting up a PhoneNo list is optional for static dialup port, but is required for dynamic dialup port.… |
| 1.3.6.1.4.1.43.2.19.4.1 | Rowa3ComPortDialPhoneListEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.43.2.19.4.1.1 | Columna3ComPortDialPhoneListPort | read-only | mandatory | Specifies the port number(portid), used as an index together with a3ComPortDialPhoneListPos, to select a particular row entry. |
| 1.3.6.1.4.1.43.2.19.4.1.2 | Columna3ComPortDialPhoneListPos | read-only | mandatory | Specifies the position(priority) in the PhoneNo list of a phone number, for this port. Used as an index together with a3ComPortDialPhoneListPort, to select a p… |
| 1.3.6.1.4.1.43.2.19.4.1.3 | Columna3ComPortDialPhoneListPhoneNo | read-write | mandatory | A text string representing a phone number in the PhoneNo list of a port. The phone number is used as the destination phone number to call for an outgoing call.… |
| 1.3.6.1.4.1.43.2.19.4.1.4 | Columna3ComPortDialPhoneListType | read-write | mandatory | Used to specify the phone type attribute of a phone number in the PhoneNo list - either of type ISDN(1) or type Analog(2) or other(3). |
| 1.3.6.1.4.1.43.2.19.4.1.5 | Columna3ComPortDialPhoneListBaud | read-write | mandatory | Used to specify the Baud rate attribute of a phone number in the PhoneList. |
| 1.3.6.1.4.1.43.2.19.4.1.6 | Columna3ComPortDialPhoneListStatus | read-write | mandatory | This object is used to add or delete a phone number from the PhoneNo list of a port. Each phone number and its associated attributes (phone type, Baud rate, an… |