A3Com-RIP-IPextns-r4-MIB
74 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | enterprises IpAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.43 | Nodea3Com | |||
| 1.3.6.1.4.1.43.2 | NodebrouterMIB | |||
| 1.3.6.1.4.1.43.2.8 | Nodea3ComRipIp | |||
| 1.3.6.1.4.1.43.2.8.1 | Scalara3RipIpUpdateTime | read-write | mandatory | This parameter specifies the time interval, in seconds, within which RIP-IP sends update packets. This parameter also determines the length of time a route lea… |
| 1.3.6.1.4.1.43.2.8.2 | Tablea3RipIpCtlTable | not-accessible | mandatory | This table contains parameters that affect the operation of RIP for IP. |
| 1.3.6.1.4.1.43.2.8.2.1 | Rowa3RipIpCtlEntry | not-accessible | mandatory | Each entry contains parameters specific to each network port on this system. |
| 1.3.6.1.4.1.43.2.8.2.1.1 | Columna3RipIpPortIndex | read-only | mandatory | This provides the port index to which the RIP-IP parameters in this table entry apply. |
| 1.3.6.1.4.1.43.2.8.2.1.2 | Columna3RipIpTalkCtl | read-write | mandatory | If talk (1) is specified, RIP-IP sends update and request packets on the specified port. If noTalk (2) is specified, no updates or requests are sent over this … |
| 1.3.6.1.4.1.43.2.8.2.1.3 | Columna3RipIpListenCtl | read-write | mandatory | If listen (1) is selected, RIP-IP receives and processes incoming update and request packets. If a3RipIpTalkCtl is set to noTalk (2), this system does not send… |
| 1.3.6.1.4.1.43.2.8.2.1.4 | Columna3RipIpTrustedNbrCtl | read-write | mandatory | This object controls how the list of trusted neighbors in a3RipIpTrustedNbrTable is to be interpreted. If this is set to include (1), RIP-IP will accept routin… |
| 1.3.6.1.4.1.43.2.8.2.1.5 | Columna3RipIpPoisonCtl | read-write | mandatory | This parameter determines how split horizon is performed. To achieve split horizon, RIP-IP refrains from advertising a route to a port if the gateway for this … |
| 1.3.6.1.4.1.43.2.8.2.1.6 | Columna3RipIpTriggerCtl | read-write | mandatory | This parameter determines if RIP-IP sends trigger update packets. Trigger update packets are sent when a route's metric has changed. By sending these update pa… |
| 1.3.6.1.4.1.43.2.8.2.1.7 | Columna3RipIpDefMetric | read-write | mandatory | This parameter specifies whether RIP-IP advertises the default route. The default route is the network with internet address 0.0.0.0 and is reported with a met… |
| 1.3.6.1.4.1.43.2.8.2.1.8 | Columna3RipIpExtPolCtl | read-write | mandatory | This parameter controls which routes learned by the Exterior Gateway Protocol (EGP) are reported by RIP-IP. If this is set to all (1), all routes learned from … |
| 1.3.6.1.4.1.43.2.8.2.1.9 | Columna3RipIpIntPolCtl | read-write | mandatory | This parameter determines which routes learned by an Interior Gateway Protocol (IGP) are reported by RIP-IP. If this is set to all (1), all routes learned from… |
| 1.3.6.1.4.1.43.2.8.2.1.10 | Columna3RipIpNetPolCtl | read-write | mandatory | This parameter determines which routes are reported by RIP-IP. The policies defined by this object and a3RipIpNetPolTable overrides the policies defined in a3R… |
| 1.3.6.1.4.1.43.2.8.2.1.11 | Columna3RipIpRcvPolCtl | read-write | mandatory | This parameter is used to filter routing updates from trusted neighbors. It allows control over which RIP routes are received and stored in the routing table. … |
| 1.3.6.1.4.1.43.2.8.2.1.12 | Columna3RipIpStaPolCtl | read-write | mandatory | This parameter is used to filter the reporting of static routes. It allows control over which static RIP routes are reported. If this is set to all (1), all st… |
| 1.3.6.1.4.1.43.2.8.2.1.13 | Columna3RipIpUnnAdvCtl | read-write | mandatory | This parameter specifies which routes are reported by RIP updates sent over an unnumbered link. If this object is set to subnetAdvUnn (1), RIP explicitly repor… |
| 1.3.6.1.4.1.43.2.8.2.1.14 | Columna3RipIpBcastCtl | read-write | mandatory | This object specifies the destination IP address to which RIP updates are sent over this port. If this object is set to subnetBcast(1), the RIP advertisement i… |
| 1.3.6.1.4.1.43.2.8.2.1.15 | Columna3RipIpExtPolAllMet | read-write | mandatory | When a3RipIpExtPolCtl is set to all, this object specifies the metric used in RIP updates of routes learned via EGP or BGP. If this object is set to zero, the … |
| 1.3.6.1.4.1.43.2.8.2.1.16 | Columna3RipIpIntPolAllMet | read-write | mandatory | When a3RipIpIntPolCtl is set to all, this object specifies the metric used in RIP updates of routes learned via OSPF or IISIS. If this object is set to zero, t… |
| 1.3.6.1.4.1.43.2.8.2.1.17 | Columna3RipIpNetPolAllMet | read-write | mandatory | When a3RipIpNetPolCtl is set to all, this object specifies the metric used in RIP updates of routes learned via RIP. If this object is set to zero, the metric … |
| 1.3.6.1.4.1.43.2.8.2.1.18 | Columna3RipIpRcvPolAllMet | read-write | mandatory | When a3RipIpRcvPolCtl is set to all, this object specifies the metric stored in the routing table when routing updates are received via RIP (from trusted neigh… |
| 1.3.6.1.4.1.43.2.8.2.1.19 | Columna3RipIpStaPolAllMet | read-write | mandatory | When a3RipIpStaPolCtl is set to all, this object specifies the metric used in RIP updates of static routes (ie, those routes entered by a user). If this object… |
| 1.3.6.1.4.1.43.2.8.2.1.20 | Columna3RipIpDynNbrCtl | read-write | mandatory | When a3RipIpDynNbrCtl is set to dynamicNbr over FR or X.25, and -RIP CONTrol is set to TALK, the neighbor list is learnt dynamically as InArp learn the IP addr… |
| 1.3.6.1.4.1.43.2.8.2.1.21 | Columna3RipIpAggregateCtl | read-write | mandatory | This parameter determines if RIP-IP aggregates subnetworks with variable-length subnet masks into one network. |
| 1.3.6.1.4.1.43.2.8.2.1.22 | Columna3RipIpDeAggregateCtl | read-write | mandatory | This parameter determines if RIP-IP de-aggregate a network into many subnetted network. |
| 1.3.6.1.4.1.43.2.8.2.1.23 | Columna3RipIpNBMAmodeCtl | read-write | mandatory | This parameter determines if the underlying NBMA network is full-mesh or non-mesh. Partial-mesh is treated as non-mesh. When this object is set to fullMesh(1),… |
| 1.3.6.1.4.1.43.2.8.3 | Tablea3RipIpExtPolTable | not-accessible | mandatory | The table contains a list of addresses learned via EGP that are to be included or excluded from RIP reports. |
| 1.3.6.1.4.1.43.2.8.3.1 | Rowa3RipIpExtPolEntry | not-accessible | mandatory | Each entry contains a single IP destination address. This destination is either included or excluded from RIP reports about routes learned via EGP. Each entry … |
| 1.3.6.1.4.1.43.2.8.3.1.1 | Columna3RipIpExtPolPort | read-only | mandatory | This defines the port to which this entry applies. |
| 1.3.6.1.4.1.43.2.8.3.1.2 | Columna3RipIpExtPolAddr | read-only | mandatory | This specifies a route destination learned via EGP that is to be included or excluded (based on a3RipIpExtPolCtl) from RIP reports. |
| 1.3.6.1.4.1.43.2.8.3.1.3 | Columna3RipIpExtPolMetric | read-write | mandatory | The metric that is to be used in RIP reports of this route. If a metric value in the range of 1 to 15 is specified, the route, together with the specified metr… |
| 1.3.6.1.4.1.43.2.8.3.1.4 | Columna3RipIpExtPolStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB. |
| 1.3.6.1.4.1.43.2.8.4 | Tablea3RipIpIntPolTable | not-accessible | mandatory | The table contains a list of addresses learned via an IGP other than RIP that are to be included or excluded from RIP reports. |
| 1.3.6.1.4.1.43.2.8.4.1 | Rowa3RipIpIntPolEntry | not-accessible | mandatory | Each entry contains a single IP destination address. This destination is either included or excluded from RIP reports. Each entry also contains a metric to be … |
| 1.3.6.1.4.1.43.2.8.4.1.1 | Columna3RipIpIntPolPort | read-only | mandatory | This defines the port to which this entry applies. |
| 1.3.6.1.4.1.43.2.8.4.1.2 | Columna3RipIpIntPolAddr | read-only | mandatory | This specifies a route destination learned via an IGP that is to be included or excluded (based on a3RipIpIntPolCtl) from RIP reports. |
| 1.3.6.1.4.1.43.2.8.4.1.3 | Columna3RipIpIntPolMetric | read-write | mandatory | The metric that is to be used in RIP reports of this route. It a metric value in the range of 1 to 15 is specified, the route, together with the specified metr… |
| 1.3.6.1.4.1.43.2.8.4.1.4 | Columna3RipIpIntPolStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB. |
| 1.3.6.1.4.1.43.2.8.5 | Tablea3RipIpNetPolTable | not-accessible | mandatory | The table contains a list of addresses that are to be included or excluded from RIP reports. Note, Network Policy overrides Static Policy, Interior Policy, and… |
| 1.3.6.1.4.1.43.2.8.5.1 | Rowa3RipIpNetPolEntry | not-accessible | mandatory | Each entry contains a single IP destination address. This destination is either included or excluded from RIP reports. Each entry also contains a metric to be … |
| 1.3.6.1.4.1.43.2.8.5.1.1 | Columna3RipIpNetPolPort | read-only | mandatory | This defines the port to which this entry applies. |
| 1.3.6.1.4.1.43.2.8.5.1.2 | Columna3RipIpNetPolAddr | read-only | mandatory | This specifies a route destination that is to be included or excluded (based on a3RipIpNetPolCtl) from RIP reports. |
| 1.3.6.1.4.1.43.2.8.5.1.3 | Columna3RipIpNetPolMetric | read-write | mandatory | The metric that is to be used in RIP reports of this route. If a metric value in the range of 1 to 15 is specified, the route, together with the specified metr… |
| 1.3.6.1.4.1.43.2.8.5.1.4 | Columna3RipIpNetPolStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB. |
| 1.3.6.1.4.1.43.2.8.6 | Tablea3RipIpRcvPolTable | not-accessible | mandatory | The table contains a list of addresses learned via trusted neighbors that are to be received and stored in the routing table. |
| 1.3.6.1.4.1.43.2.8.6.1 | Rowa3RipIpRcvPolEntry | not-accessible | mandatory | Each entry contains a single IP destination address. This destination is either stored or not stored when RIP reports from trusted neighbors are received. Each… |
| 1.3.6.1.4.1.43.2.8.6.1.1 | Columna3RipIpRcvPolPort | read-only | mandatory | This defines the port to which this entry applies. |
| 1.3.6.1.4.1.43.2.8.6.1.2 | Columna3RipIpRcvPolAddr | read-only | mandatory | This specifies a route destination that is to be stored or not stored (based on a3RipIpRcvPolCtl) when RIP reports from trusted neighbors are received. |
| 1.3.6.1.4.1.43.2.8.6.1.3 | Columna3RipIpRcvPolMetric | read-write | mandatory | The metric that is to be used in the routing table entry for this route. It a metric value in the range of 1 to 15 is specified, the route, together with the s… |
| 1.3.6.1.4.1.43.2.8.6.1.4 | Columna3RipIpRcvPolStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB. |
| 1.3.6.1.4.1.43.2.8.7 | Tablea3RipIpStaPolTable | not-accessible | mandatory | The table contains a list of static addresses that are to be included or excluded from RIP reports. |
| 1.3.6.1.4.1.43.2.8.7.1 | Rowa3RipIpStaPolEntry | not-accessible | mandatory | Each entry contains a single IP destination address representing a static route. This destination is either included or excluded from RIP reports. Each entry a… |
| 1.3.6.1.4.1.43.2.8.7.1.1 | Columna3RipIpStaPolPort | read-only | mandatory | This defines the port to which this entry applies. |
| 1.3.6.1.4.1.43.2.8.7.1.2 | Columna3RipIpStaPolAddr | read-only | mandatory | This specifies a route destination learned statically that is to be included or excluded (based on a3RipIpStaPolCtl) from RIP reports. |
| 1.3.6.1.4.1.43.2.8.7.1.3 | Columna3RipIpStaPolMetric | read-write | mandatory | The metric that is to be used in RIP reports of this route. It a metric value in the range of 1 to 15 is specified, the route, together with the specified metr… |
| 1.3.6.1.4.1.43.2.8.7.1.4 | Columna3RipIpStaPolStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB. |
| 1.3.6.1.4.1.43.2.8.8 | Tablea3RipIpNeighborTable | not-accessible | mandatory | This table contains a list of neighbor addresses that RIP-IP uses to determine to which neighbors it should send update packets. RIP-IP neighbors are router th… |
| 1.3.6.1.4.1.43.2.8.8.1 | Rowa3RipIpNeighborEntry | not-accessible | mandatory | Each entry contains information about a single RIP-IP neighbor. The information include the neighbor's IP address as well as the port from which it can be reac… |
| 1.3.6.1.4.1.43.2.8.8.1.1 | Columna3RipIpNeighborPort | read-only | mandatory | This indicates the port from which this neighbor can be reached. The neighbor must be attached to the same network as this port. |
| 1.3.6.1.4.1.43.2.8.8.1.2 | Columna3RipIpNeighborAddr | read-only | mandatory | This specifies the IP address of the RIP-IP neighbor. |
| 1.3.6.1.4.1.43.2.8.8.1.3 | Columna3RipIpNeighborStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB. |
| 1.3.6.1.4.1.43.2.8.9 | Tablea3RipIpTrustedNbrTable | not-accessible | mandatory | This table contains a list of RIP-IP neighbors from which RIP-IP accepts packets. If this table contains no entries for a particular port, RIP-IP will accept a… |
| 1.3.6.1.4.1.43.2.8.9.1 | Rowa3RipIpTrustedNbrEntry | not-accessible | mandatory | Each entry identifies a trusted neighbor from which RIP-IP will accept routing packets. |
| 1.3.6.1.4.1.43.2.8.9.1.1 | Columna3RipIpTrustedNbrPort | read-only | mandatory | This specifies the port for which this table entry applies. |
| 1.3.6.1.4.1.43.2.8.9.1.2 | Columna3RipIpTrustedNbrAddr | read-only | mandatory | This identifies the IP address of a trusted neighbor from which RIP-IP will accept (or not, depending on the value of a3RipIpTrustedNbrCtl) routing packets. |
| 1.3.6.1.4.1.43.2.8.9.1.3 | Columna3RipIpTrustedNbrStatus | read-write | mandatory | This object is used to add and delete entries in this table. See the notes describing RowStatus at the beginning of this MIB. |
| 1.3.6.1.4.1.43.2.8.10 | Tablea3RipIpImpMetTable | not-accessible | mandatory | This table specifies the operations to be performed on metrics imported from other routing update protocols before they are reported by RIP. |
| 1.3.6.1.4.1.43.2.8.10.1 | Rowa3RipIpImpMetEntry | not-accessible | mandatory | Each entry specifies the operations to be performed on the metric imported from a specific routing update protocol before it is reported by RIP. |
| 1.3.6.1.4.1.43.2.8.10.1.1 | Columna3RipIpImpMetProtocol | read-only | mandatory | This object identifies the routing update protocol from which metrics (and routes) are imported. |
| 1.3.6.1.4.1.43.2.8.10.1.2 | Columna3RipIpImpMetOperation | read-write | mandatory | This specifies the operation to be performed on the native protocol metric before it is reported by RIP. |
| 1.3.6.1.4.1.43.2.8.10.1.3 | Columna3RipIpImpMetOperand | read-write | mandatory | This specifies the operand of the operation specified by the corresponding instance of a3RipIpImpMetOperation. See the comments describing this table for more … |