ACKSYS-MIB
1174 objects
SNMPv2C Module for ACKSYS Solutions
Imported Objects
| SNMPv2-SMI | Counter32 enterprises Gauge32 Integer32 IpAddress mgmt MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DateAndTime DisplayString RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.28097 | Identityacksys | SNMPv2C Module for ACKSYS Solutions | ||
| 1.3.6.1.4.1.28097.1 | Nodenetwork-product | |||
| 1.3.6.1.4.1.28097.1.1 | NodewifiInterface | |||
| 1.3.6.1.4.1.28097.1.1.1 | Nodesettings | |||
| 1.3.6.1.4.1.28097.1.1.1.1 | ScalarsettingInterfaceSsid | read-write | current | SSID (wireless network name) [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.2 | ScalarsettingInterfaceWifiMode | read-write | current | Select between MAX-ACCESS POINT and BRIDGE [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.3 | ScalarsettingInterfaceChannel | read-write | current | A wireless network uses specific channels to handle communication between clients. Some channels in your area may have interference from other electronic devic… |
| 1.3.6.1.4.1.28097.1.1.1.4 | ScalarsettingInterface80211Mode | read-write | current | Select IEEE 802.11x compatibility mode. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.5 | ScalarsettingInterfaceSuper-a-g-Mode | read-write | current | This parameter enables the SUPER A/G mode to reach the 108 Mbits/s speed. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.6 | ScalarsettingEnableRadio | read-write | current | Enable / Disable wifi radio [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.7 | ScalarsettingTxPower | read-write | current | Set WIFI tx power [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.8 | ScalarsettingRegion | read-write | current | Set WIFI regulation domain [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9 | NodesecuritySettings | |||
| 1.3.6.1.4.1.28097.1.1.1.9.1 | ScalarsecurityMode | read-write | current | Set the security mode [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.2 | NodesecurityWEP | |||
| 1.3.6.1.4.1.28097.1.1.1.9.2.1 | ScalarsecurityModeWepKeyLen | read-write | current | Set the WEP key len (64 bits or 128 bits) [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.2.2 | ScalarsecurityModeWepKey-1 | read-write | current | WEP key 1 in hexadecimal format [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.2.3 | ScalarsecurityModeWepKey-2 | read-write | current | WEP key 2 in hexadecimal format [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.2.4 | ScalarsecurityModeWepKey-3 | read-write | current | WEP key 3 in hexadecimal format [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.2.5 | ScalarsecurityModeWepKey-4 | read-write | current | WEP key 4 in hexadecimal format [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.2.6 | ScalarsecurityModeDefaultWepKey | read-write | current | Set the wep key used [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.2.7 | ScalarsecurityModeWepAuthentication | read-write | current | Set WEP Authentication [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3 | NodesecurityWPA-WPA2 | |||
| 1.3.6.1.4.1.28097.1.1.1.9.3.1 | NodesecurityPresharedKey | |||
| 1.3.6.1.4.1.28097.1.1.1.9.3.1.1 | ScalarsecurityModeWpaPresharedKey | read-write | current | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2 | NodesecurityRadius | |||
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.1 | ScalarsecurityModeWPARadiusAuthenticationTimeout | read-write | obsolete | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.2 | ScalarsecurityModeWPARadiusIP | read-write | obsolete | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.3 | ScalarsecurityModeWPARadiusPort | read-write | obsolete | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.4 | ScalarsecurityModeWPARadiusSecret | read-write | obsolete | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.5 | ScalarsecurityModeWPARadiusMacAddressAuthentication | read-write | obsolete | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.6 | NodesecurityRadiusAP | |||
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.6.1 | ScalarsecurityModeWPARadiusAPAuthenticationTimeout | read-write | current | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.6.2 | ScalarsecurityModeWPARadiusAPIP | read-write | current | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.6.3 | ScalarsecurityModeWPARadiusAPPort | read-write | current | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.6.4 | ScalarsecurityModeWPARadiusAPSecret | read-write | current | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.6.5 | ScalarsecurityModeWPARadiusAPMacAddressAuthentication | read-write | current | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.6.6 | NodesecurityRadiusAPBackup | |||
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.6.6.1 | ScalarsecurityModeWPABackupRadiusAPIP | read-write | current | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.6.6.2 | ScalarsecurityModeWPARadiusBackupAPPort | read-write | current | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.6.6.3 | ScalarsecurityModeWPARadiusBackupAPSecret | read-write | current | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.6.6.4 | ScalarsecurityModeWPABackupRadiusAPMacAddressAuthentication | read-write | current | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.7 | NodesecurityRadiusBridge | |||
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.7.1 | ScalarsecurityModeWPARadiusLogin | read-write | current | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.2.7.2 | ScalarsecurityModeWPARadiusPassword | read-write | current | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.3 | NodesecurityBackupRadius | |||
| 1.3.6.1.4.1.28097.1.1.1.9.3.3.1 | ScalarsecurityModeWPABackupRadiusIP | read-write | obsolete | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.3.2 | ScalarsecurityModeWPARadiusBackupPort | read-write | obsolete | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.3.3 | ScalarsecurityModeWPARadiusBackupSecret | read-write | obsolete | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.3.4 | ScalarsecurityModeWPABackupRadiusMacAddressAuthentication | read-write | obsolete | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.4 | ScalarsecurityModeWpaMode | read-write | current | Select the wpa mode [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.5 | ScalarsecurityModeWpaCipherType | read-write | current | select the cipher type [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.9.3.6 | ScalarsecurityModeWpaKeyUpdateInterval | read-write | current | Set the group key interval [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.10 | ScalarsettingAntennaChoice | read-write | current | Set the antenna type [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.11 | ScalarsettingTransmisionRate | read-write | current | Set the transmission rate in Mbps Automatic : -1 With SuperAG Mode : 108,96,72,48,36,24,18,12 Without SuperAG mode : 54,48,36,24,18,12,9,6 802.11b mode : 11,5.… |
| 1.3.6.1.4.1.28097.1.1.1.12 | ScalarsettingFlagUdapnopassword | read-write | current | Configure LAN settings without password [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.13 | ScalarsettingFlagFiltersamenet | read-write | current | Isolate subnet filter [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.14 | ScalarsettingFlagFilterframecosom | read-write | current | Setting economy filter [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.15 | ScalarsettingDFSsupport | read-write | current | Setting DFS support [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.16 | ScalarsettingFilterCustomIpAddr | read-write | current | IP address of the custom subnet [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.1.17 | ScalarsettingFilterCustomSubnetMask | read-write | current | Subnet mask of the custom subnet [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2 | Nodebridge-mode | |||
| 1.3.6.1.4.1.28097.1.1.2.1 | Scalarbridge-modeLinkStatus | read-only | current | MAX-ACCESS POINT's connection status. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.2 | Scalarbridge-modeMacAP | read-only | current | MAX-ACCESS POINT's MAC ADDRESS we are connected with. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.3 | Scalarbridge-modeRSSI | read-only | current | MAX-ACCESS POINT's connection RSSI. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.4 | Scalarbridge-modeRSSIdBm | read-only | current | Connection's RSSI in dBm. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.5 | Scalarbridge-modeRSSIPercent | read-only | current | Connection's RSSI in percent. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.6 | Scalarbridge-modeCurrentTxRate | read-only | current | Current communication speed in bits per second. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.7 | Scalarbridge-WirelessMode | read-write | current | Select the Wireless mode. Infrastructure mode require an access point. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8 | NodebridgeAPFiltering | |||
| 1.3.6.1.4.1.28097.1.1.2.8.1 | ScalarbridgeAPFilteringEnable | read-write | current | Enable or Disable AP Filtering. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8.2 | ScalarbridgeAPFilteringMode | read-write | current | Select AP Filtering Mode (allow/Deny) [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8.3 | ScalarbridgeAPFilteringMACAddress | read-write | current | MAC address field [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8.4 | ScalarbridgeAPFilteringName | read-write | current | Name Field [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8.5 | ScalarbridgeAPFilteringSave | read-write | current | write 1 to save the rule [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8.6 | ScalarbridgeAPFilteringDelete | read-write | current | when writed, delete the rule which is indexed by the written value [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8.7 | ScalarbridgeAPFilteringEnableRule | read-write | current | when writed, enable the rule which is indexed by the written value [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8.8 | ScalarbridgeAPFilteringDisableRule | read-write | current | when writed, disable the rule which is indexed by the written value [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8.9 | TablebridgeAPFilteringTable | not-accessible | current | Significant only in MAX-ACCESS POINT mode. This table shows information bridge AP filtering rules list. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8.9.1 | RowbridgeAPFilteringEntry | not-accessible | current | Shows information of the rule. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8.9.1.1 | ColumnbridgeAPFilteringListId | read-only | current | Rule index. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8.9.1.2 | ColumnbridgeAPFilteringListName | read-only | current | Show rule's name [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8.9.1.3 | ColumnbridgeAPFilteringListMAC | read-only | current | MAC address of the client. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.8.9.1.4 | ColumnbridgeAPFilteringListEnable | read-only | current | Show if a rule is enabled or not. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.9 | NodebridgeRoaming | |||
| 1.3.6.1.4.1.28097.1.1.2.9.1 | NodebridgeRoamingAdvanced | |||
| 1.3.6.1.4.1.28097.1.1.2.9.1.1 | ScalarbridgeRoamingAdvancedScanThreshold-dbm | read-write | current | Allows to configure the RSSI scan threshold in dBm from which the access point active scan will start. The access point active scan process looking on each val… |
| 1.3.6.1.4.1.28097.1.1.2.9.1.2 | ScalarbridgeRoamingAdvancedScanThreshold-percent | read-write | current | Allows to configure the RSSI scan threshold in percent from which the access point active scan will start. The access point active scan process looking on each… |
| 1.3.6.1.4.1.28097.1.1.2.9.1.3 | ScalarbridgeRoamingAdvancedScanPeriod | read-write | current | Allow to configure the time between two scan. Reduce this time increase the Access Point discover, but decrease the bandwith if you used more one channel. [FW:… |
| 1.3.6.1.4.1.28097.1.1.2.9.1.4 | ScalarbridgeRoamingAdvancedScanDuration | read-write | current | Allow to configure the duration while the bridge waiting the Access Point answer. Reduce this duration increase the Bandwith when you used more one channel, bu… |
| 1.3.6.1.4.1.28097.1.1.2.9.1.5 | ScalarbridgeRoamingAdvancedAPLossDetection | read-write | current | If nothing is received from the AP during a certain amount of time, it will be considered unreachable. This amount of time is computed as: 'AP timeout' = 'AP l… |
| 1.3.6.1.4.1.28097.1.1.2.9.2 | ScalarbridgeRoamingEnable | read-write | current | Roaming enables WiFi clients to roam among AP when WiFi RSSI of the current AP becomes weak. This radio button enables/disables the roaming capabilities of the… |
| 1.3.6.1.4.1.28097.1.1.2.9.3 | ScalarbridgeRoamingRSSIThreshold-dBm | read-write | current | Allows to configure the RSSI roaming threshold in dBm from which the roaming algorithm (to find a better AP) will start. AP changing will only be effective if … |
| 1.3.6.1.4.1.28097.1.1.2.9.4 | ScalarbridgeRoamingRSSIThreshold-percent | read-write | current | Allows to configure the RSSI roaming threshold in percent from which the roaming algorithm (to find a better AP) will start. AP changing will only be effective… |
| 1.3.6.1.4.1.28097.1.1.2.10 | ScalarbridgeChannelList | read-write | current | A wireless network uses specific channels in the 2.4GHz or 5GHz wireless spectrum to handle communication between clients. Some channels in your area may have … |
| 1.3.6.1.4.1.28097.1.1.2.11 | NodebridgeWirelessScan | |||
| 1.3.6.1.4.1.28097.1.1.2.11.1 | TablebridgeWileressScanTable | not-accessible | current | Significant only in MAX-ACCESS POINT mode. This table shows information AP bridge filtering rules list. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.11.1.1 | RowbridgeWirelessScanEntry | not-accessible | current | Shows information of the rule. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.11.1.1.1 | ColumnbridgeWirelessScanAPMac | read-only | current | MAC address of the access point. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.11.1.1.2 | ColumnbridgeWirelessScanSSID | read-only | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.11.1.1.3 | ColumnbridgeWirelessScanChannel | read-only | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.11.1.1.4 | ColumnbridgeWirelessScanMode | read-only | current | Show AP's IEEE 802.11x compatibility mode. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.11.1.1.5 | ColumnbridgeWirelessScanSecurity | read-only | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.11.1.1.6 | ColumnbridgeWirelessScanRssi | read-only | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12 | NodebridgeNAT | |||
| 1.3.6.1.4.1.28097.1.1.2.12.1 | ScalarbrigeNATStatus | read-write | current | Enable / disable NAT [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.2 | ScalarbrigeNATEnablePing | read-write | current | Enable / disable ping response from WAN [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.3 | ScalarbrigeNATEnableProductWebServer | read-write | current | Enable / disable the internal web server from WAN [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.4 | ScalarbrigeNATInternalWebServerPort | read-write | current | TCP port used by internal web server from WAN [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.5 | ScalarbrigeNATEnableProductSnmpServer | read-write | current | Enable / disable the internal snmp server from WAN [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.6 | ScalarbrigeNATInternalWebSnmpPort | read-write | current | TCP port used by internal snmp server from WAN [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.7 | ScalarbrigeNATWanIpAddrMode | read-write | current | Ip address mode on wan side [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.8 | ScalarbrigeNATWanIpAddr | read-write | current | Static Ip address on wan side [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.9 | ScalarbrigeNATWanSubnetMask | read-write | current | Subnet mask on wan side [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.10 | ScalarbrigeNATWanGateway | read-write | current | Gateway ip address on wan side [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11 | NodebridgeNatPortForwarding | |||
| 1.3.6.1.4.1.28097.1.1.2.12.11.1 | TablebridgeNatPortForwardingTable | not-accessible | current | This table show information on port forwading rules [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.1.1 | RowbridgeNatPortForwardingEntry | not-accessible | current | Shows information of rule. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.1.1.1 | ColumnbridgeNatPortForwardingListId | read-only | current | Rule index [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.1.1.2 | ColumnbridgeNatPortForwardingListName | read-only | current | Show rule's name [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.1.1.3 | ColumnbridgeNatPortForwardingListIpAddr | read-only | current | Show ipaddress to forward data [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.1.1.4 | ColumnbridgeNatPortForwardingListPublicTcpPort | read-only | current | Show public TCP port [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.1.1.5 | ColumnbridgeNatPortForwardingListPrivateTcpPort | read-only | current | Show private TCP port [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.1.1.6 | ColumnbridgeNatPortForwardingListPublicUdpPort | read-only | current | Show public TCP port [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.1.1.7 | ColumnbridgeNatPortForwardingListPrivateUdpPort | read-only | current | Show private TCP port [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.1.1.8 | ColumnbridgeNatPortForwardingListEnable | read-only | current | Rule state [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.2 | ScalarbridgeNatPortForwardingName | read-write | current | Show rule's name [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.3 | ScalarbridgeNatPortForwardingIpAddr | read-write | current | Show ipaddress to forward data [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.4 | ScalarbridgeNatPortForwardingPublicTcpPort | read-write | current | Show public TCP port [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.5 | ScalarbridgeNatPortForwardingPrivateTcpPort | read-write | current | Show private TCP port [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.6 | ScalarbridgeNatPortForwardingPublicUdpPort | read-write | current | Show public TCP port [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.7 | ScalarbridgeNatPortForwardingPrivateUdpPort | read-write | current | Show private TCP port [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.8 | ScalarbridgeNatPortForwardingEnableRule | read-write | current | when writed, enable the rule which is indexed by the written value [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.9 | ScalarbridgeNatPortForwardingDisableRule | read-write | current | when writed, disable the rule which is indexed by the written value [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.10 | ScalarbridgeNatPortForwardingSaveRule | read-write | current | when writed, save the rule which is indexed by the written value [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.2.12.11.11 | ScalarbridgeNatPortForwardingDeleteRule | read-write | current | when writed, delete the rule which is indexed by the written value [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3 | Nodeaccess-point-mode | |||
| 1.3.6.1.4.1.28097.1.1.3.1 | TableapClientTable | not-accessible | current | Significant only in MAX-ACCESS POINT mode. This table shows information about connected clients. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.1.1 | RowapClientEntry | not-accessible | current | Shows information about the connected client. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.1.1.1 | ColumnclientMacAddr | read-only | current | MAC address of the client connected to the AP. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.1.1.2 | Columnclient80211Mode | read-only | current | Show client's IEEE 802.11x compatibility mode. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.1.1.3 | ColumnclientTxRate | read-only | current | Client's communication speed in bits per second [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.1.1.4 | ColumnclientRssiPercent | read-only | current | Client's RSSI (percent) [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.2 | ScalarapAutomaticChannel | read-write | current | Enable / disable the automatic channel select [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.3 | ScalarapClientCount | read-only | current | count the number of entries in ApClientEntry [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4 | NodeapClientFiltering | |||
| 1.3.6.1.4.1.28097.1.1.3.4.1 | ScalarapClientFilteringEnable | read-write | current | Enable / Disable Client Filtering. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.2 | ScalarapClientFilteringMode | read-write | current | Select Client Filtering Mode (allow/Deny) [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.3 | ScalarapClientWirelessFiltering | read-write | current | Enable or disable Wireless client filtering [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.4 | ScalarapClientWiredFiltering | read-write | current | Enable or disable Wireless client filtering [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.5 | ScalarapClientFilteringMACAddress | read-write | current | MAC address field [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.6 | ScalarapClientFilteringName | read-write | current | Name Field [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.7 | ScalarapClientFilteringSave | read-write | current | write 1 to save the rule [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.8 | ScalarapClientFilteringDelete | read-write | current | when writed, delete the rule which is indexed by the written value [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.9 | ScalarapClientFilteringEnableRule | read-write | current | when writed, enable the rule which is indexed by the written value [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.10 | ScalarapClientFilteringDisableRule | read-write | current | when writed, disable the rule which is indexed by the written value [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.11 | TableapClientFilteringTable | not-accessible | current | Significant only in MAX-ACCESS POINT mode. This table shows information AP bridge filtering rules list. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.11.1 | RowapClientFilteringEntry | not-accessible | current | Shows information of the rule. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.11.1.1 | ColumnapClientFilteringListId | read-only | current | Rule index. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.11.1.2 | ColumnapClientFilteringListName | read-only | current | Show rule's name [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.11.1.3 | ColumnapClientFilteringListMAC | read-only | current | MAC address of the client. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.4.11.1.4 | ColumnapClientFilteringListEnable | read-only | current | Show if the rule is enabled or not. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.5 | Nodewds | |||
| 1.3.6.1.4.1.28097.1.1.3.5.1 | ScalarapWDSEnable | read-write | current | Enable or Disable WDS. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.5.2 | ScalarapWDSEnableSTP | read-write | current | Enable or Disable STP when WDS is on [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.5.3 | ScalarapWDSMAC1 | read-write | current | First AP mac address [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.5.4 | ScalarapWDSMAC2 | read-write | current | Second AP mac address [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.5.5 | ScalarapWDSMAC3 | read-write | current | Third AP mac address [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.5.6 | ScalarapWDSMAC4 | read-write | current | Fourth AP mac address [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.5.7 | ScalarapWDSMAC5 | read-write | current | Fifth AP mac address [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.5.8 | ScalarapWDSMAC6 | read-write | current | Sixth AP mac address [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.6 | ScalarsettingSSIDVisibility | read-write | current | Enable or Disable SSID Visibility [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.7 | ScalarenableSTP | read-write | current | Enable / disable STP protocol. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.8 | NodelanTimeOutSettings | |||
| 1.3.6.1.4.1.28097.1.1.3.8.1 | ScalarenableLanTimeout | read-write | current | Enable / disable LAN timeout. ACCESS POINT can be configured to auto-disconnect the radio when the LAN is disconnected from the equipment. [FW:E2080.AC.1:5.52.… |
| 1.3.6.1.4.1.28097.1.1.3.8.2 | ScalarlanTimeoutIPSurvey | read-write | current | Define the IP address where the probe was be sent. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.8.3 | ScalarlanTimeoutMaxProbe | read-write | current | Define the number of probe without response necessairy to disconnect the radio. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.8.4 | ScalarlanTimeoutProbeTimeout | read-write | current | Define the probe response waiting time in seconds. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.3.8.5 | ScalarlanTimeoutProbeInterval | read-write | current | Define the times in seconds between each probes. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.4 | NodeadvancedSettings | |||
| 1.3.6.1.4.1.28097.1.1.4.1 | NodelongDistanceSettings | |||
| 1.3.6.1.4.1.28097.1.1.4.1.1 | ScalarenableLongDistance | read-write | current | Enable / disable distance parameter. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.4.1.2 | ScalardistanceAntennaMeter | read-write | current | Set the distance between antenna in meter. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.4.1.3 | ScalardistanceSlotTime | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.4.1.4 | ScalardistanceAckTimeout | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.4.1.5 | ScalardistanceCtsTimeout | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.4.2 | Scalarenable802-11d | read-write | current | Enable / disable the 802.11d. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.1.4.3 | ScalarenableIsolateSTA | read-write | current | Enable / disable the isolating access point. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.2 | Nodeadministration | |||
| 1.3.6.1.4.1.28097.1.2.1 | ScalaradminReset | read-write | current | Writing 1 resets the product. This must be done after each configuration change. [FW:E2080.AC.1:5.52.0] [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.1.2.2 | ScalaradminResetFactory | read-write | current | Writing 1 resets the product to the factory settings. [FW:E2080.AC.1:5.52.0] [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.1.2.3 | ScalaradminEnableWebServer | read-write | current | Enable or Disable internal webserver. Not supported on the WLn- products series. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.2.4 | ScalaradminAutoSave | read-write | current | Enable or Disable the automatic saving of changes. When this function is disabled, modifications are not saved automatically after change and some OID are appl… |
| 1.3.6.1.4.1.28097.1.2.5 | ScalaradminSave | read-write | current | Write 1 to save the modification in flash. Read this OID to know if a save is require. [FW:E2080.AC.1:5.52.0] [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.1.2.6 | ScalaradminApply | read-write | current | When set to 'Enable', applies configuration changes without rebooting the product. The value returns to 'Disable' after execution. The value return 'apply_requ… |
| 1.3.6.1.4.1.28097.1.2.7 | ScalaradminConfigHash | read-only | current | Hash value of configuration file [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.1.2.8 | NodefileTransfer | |||
| 1.3.6.1.4.1.28097.1.2.8.1 | ScalarfileTransferAction | read-write | current | file {upload to/download from} product [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.1.2.8.2 | ScalarfileTransferType | read-write | current | Type of file to transfer: 1.configuration back up; 2.firmware file; 3.LTE radio firmware; 4.WIDS configuration [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.1.2.8.3 | ScalarfileTransferSize | read-write | current | Maximum size of file chunks to transfer [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.1.2.8.4 | ScalarfileTransferIndex | read-write | current | Index of chunk to transfer [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.1.2.8.5 | ScalarfileTransferHash | read-write | current | Hash value of file to transfer [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.1.2.8.6 | ScalarfileTransferChunk | read-write | current | File chunk to transfer; includes Size bytes at file offset Index*Size [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.1.2.8.7 | ScalarfileTransferResult | read-only | current | Transfer result [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.1.2.8.8 | ScalarfileTransferSession | read-only | current | Transfer session [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.1.2.9 | ScalaradminIdentify | read-write | current | Flash the product diagnostic LED. Return 0 after get. [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.1.2.10 | NodeadminEvents | |||
| 1.3.6.1.4.1.28097.1.2.10.1 | ScalaradminEventDisable | read-write | current | Disable (i.e. reset) action for the named alarm [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.1.2.10.2 | ScalaradminEventEnable | read-write | current | Enable (i.e. set) action for the named alarm [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.1.2.10.3 | ScalaradminEventTrigger | read-write | current | Execute action for the named one-shot alarm [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.1.2.11 | NodeadminTimeZone | |||
| 1.3.6.1.4.1.28097.1.2.11.1 | ScalaradminTimeZoneDBVersion | read-only | current | Returns the iana Time Zone Database version Please see: https://www.iana.org/time-zones [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.1.2.11.2 | ScalaradminTimeZoneName | read-write | current | Set Time Zone name as defined in the iana Time Zone Database Please see: https://www.iana.org/time-zones example: (This an extract from the database, but it ma… |
| 1.3.6.1.4.1.28097.1.2.12 | NodeadminSystemDateAndTime | |||
| 1.3.6.1.4.1.28097.1.2.12.1 | ScalaradminSystemDateAndTimeLocal | read-write | current | The system current date and time expressed relative to the configured Time Zone. For Write operation, only 8 OCTETs can be set, as the 3 remaining octets reser… |
| 1.3.6.1.4.1.28097.1.2.12.2 | ScalaradminSystemDateAndTimeUTC | read-write | current | The system current date and time expressed in UTC. For Write operation, only 8 OCTETs can be set, as the 3 remaining octets reserved for the direction from UTC… |
| 1.3.6.1.4.1.28097.1.3 | Nodeos-stat | |||
| 1.3.6.1.4.1.28097.1.3.1 | Scalaros-statFreeHeap | read-only | current | The amount of memory currently available, measured in bytes. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.3.2 | Scalaros-statTotalHeap | read-only | current | The total size of the heap, measured in bytes. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.3.3 | Scalaros-statHeapLowWater | read-only | current | Low water mark for the heap. Writing any value this variable will always reset the low water to the total heap size. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.3.4 | Scalaros-statNetpageFree | read-only | current | The amount of netpages currently available, measured in bytes. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.3.5 | Scalaros-statNetpageLowWater | read-only | current | Low water mark for the netpage. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.4 | NodeproductSpecific | |||
| 1.3.6.1.4.1.28097.1.4.1 | Nodewlg-aboard | |||
| 1.3.6.1.4.1.28097.1.4.1.1 | Scalarwlg-aboard-PW1-state | read-only | obsolete | Power 1 state [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.4.1.2 | Scalarwlg-aboard-PW2-state | read-only | obsolete | Power 2 state [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.5 | NodelanInterface | |||
| 1.3.6.1.4.1.28097.1.5.1 | ScalarlanInterfaceIpAddrMode | read-write | current | Static or DHCP Ip settings [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.5.2 | ScalarlanInterfaceIpAddr | read-write | current | Product IP address [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.5.3 | ScalarlanInterfaceSubNetMask | read-write | current | Network mask [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.5.4 | ScalarlanInterfaceGatewayIp | read-write | current | IP gateway [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.5.5 | ScalarlanInterfaceHostName | read-write | current | Host name [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.5.6 | ScalarlanInterfaceLocalDomainName | read-write | current | Local Domain Name [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.1.6 | NodeserialInterface | |||
| 1.3.6.1.4.1.28097.1.6.1 | ScalarserialServicetype | read-write | current | Define the type of service provided to the remote stations [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.2 | NodeserialFormat | |||
| 1.3.6.1.4.1.28097.1.6.2.1 | ScalarserialFormatBaudRate | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.2.2 | ScalarserialFormatDataBit | read-write | current | 6,7,8 data bit [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.2.3 | ScalarserialFormatParityBit | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.2.4 | ScalarserialFormatStopBit | read-write | current | 1 or 2 stop bits [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.2.5 | ScalarserialElectricalInterface | read-write | current | Select electrical serial interface (RS232, RS422 master / slave, RS485 echo /no echo [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.3 | NodeserialSendTriggers | |||
| 1.3.6.1.4.1.28097.1.6.3.1 | NodeserialSendTriggerCharcount | |||
| 1.3.6.1.4.1.28097.1.6.3.1.1 | ScalarsendTriggerCharCountEnable | read-write | current | Enable / disable this sendtrigger [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.3.1.2 | ScalarsendTriggerCharCountValue | read-write | current | number of chars required in the buffer before emission to the client application. [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.3.2 | NodeserialSendTriggerIdleDelay | |||
| 1.3.6.1.4.1.28097.1.6.3.2.1 | ScalarsendTriggerIdleDelayEnable | read-write | current | Enable / disable this sendtrigger [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.3.2.2 | ScalarsendTriggerIdleDelayValue | read-write | current | delay between last char reception and emission to the client application [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.3.2.3 | ScalarsendTriggerIdleDelayUnit | read-write | current | Unit [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.3.3 | NodeserialSendTriggerFrameDelay | |||
| 1.3.6.1.4.1.28097.1.6.3.3.1 | ScalarsendTriggerFrameDelayEnable | read-write | current | Enable / disable this sendtrigger [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.3.3.2 | ScalarsendTriggerFrameDelayValue | read-write | current | delay between char reception and emission to the client application. [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.3.3.3 | ScalarsendTriggerFrameDelayUnit | read-write | current | Unit of send trigger [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.4 | NodeserialServiceVirtualCom | |||
| 1.3.6.1.4.1.28097.1.6.5 | NodeserialServiceModbusSlave | |||
| 1.3.6.1.4.1.28097.1.6.5.1 | ScalarmodbusSlaveFormat | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.5.2 | ScalarmodbusSlaveSerialTransactionTimeout | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6 | NodeserialServiceModbusMaster | |||
| 1.3.6.1.4.1.28097.1.6.6.1 | ScalarmodbusMasterFormat | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.2 | ScalarmodbusMasterTransactionTimeout | read-write | current | If the MODBUS/TCP slave device does not respond in the given time, an error response will be sent to the serial master. [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3 | NodemodbusMasterForwardingTable | |||
| 1.3.6.1.4.1.28097.1.6.6.3.1 | NodemodbusMasterForwardingTable-Rule1 | |||
| 1.3.6.1.4.1.28097.1.6.6.3.1.1 | ScalarmmForwardingTable-Rule1-FirstLocalAddr | read-write | current | First MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.1.2 | ScalarmmForwardingTable-Rule1-LastLocalAddr | read-write | current | Last MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.1.3 | ScalarmmForwardingTable-Rule1-FirstRemoteAddr | read-write | current | First MODBUS TCP ID field (remote serial address) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.1.4 | ScalarmmForwardingTable-Rule1-SlaveIpAddrIncrement | read-write | current | 1 = last byte of IP address fixed 2 = last byte of IP address variable [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.1.5 | ScalarmmForwardingTable-Rule1-SlaveIpAddr | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.2 | NodemodbusMasterForwardingTable-Rule2 | |||
| 1.3.6.1.4.1.28097.1.6.6.3.2.1 | ScalarmmForwardingTable-Rule2-FirstLocalAddr | read-write | current | First MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.2.2 | ScalarmmForwardingTable-Rule2-LastLocalAddr | read-write | current | Last MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.2.3 | ScalarmmForwardingTable-Rule2-FirstRemoteAddr | read-write | current | First MODBUS TCP ID field (remote serial address) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.2.4 | ScalarmmForwardingTable-Rule2-SlaveIpAddrIncrement | read-write | current | 1 = last byte of IP address fixed 2 = last byte of IP address variable [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.2.5 | ScalarmmForwardingTable-Rule2-SlaveIpAddr | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.3 | NodemodbusMasterForwardingTable-Rule3 | |||
| 1.3.6.1.4.1.28097.1.6.6.3.3.1 | ScalarmmForwardingTable-Rule3-FirstLocalAddr | read-write | current | First MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.3.2 | ScalarmmForwardingTable-Rule3-LastLocalAddr | read-write | current | Last MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.3.3 | ScalarmmForwardingTable-Rule3-FirstRemoteAddr | read-write | current | First MODBUS TCP ID field (remote serial address) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.3.4 | ScalarmmForwardingTable-Rule3-SlaveIpAddrIncrement | read-write | current | 1 = last byte of IP address fixed 2 = last byte of IP address variable [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.3.5 | ScalarmmForwardingTable-Rule3-SlaveIpAddr | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.4 | NodemodbusMasterForwardingTable-Rule4 | |||
| 1.3.6.1.4.1.28097.1.6.6.3.4.1 | ScalarmmForwardingTable-Rule4-FirstLocalAddr | read-write | current | First MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.4.2 | ScalarmmForwardingTable-Rule4-LastLocalAddr | read-write | current | Last MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.4.3 | ScalarmmForwardingTable-Rule4-FirstRemoteAddr | read-write | current | First MODBUS TCP ID field (remote serial address) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.4.4 | ScalarmmForwardingTable-Rule4-SlaveIpAddrIncrement | read-write | current | 1 = last byte of IP address fixed 2 = last byte of IP address variable [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.4.5 | ScalarmmForwardingTable-Rule4-SlaveIpAddr | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.5 | NodemodbusMasterForwardingTable-Rule5 | |||
| 1.3.6.1.4.1.28097.1.6.6.3.5.1 | ScalarmmForwardingTable-Rule5-FirstLocalAddr | read-write | current | First MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.5.2 | ScalarmmForwardingTable-Rule5-LastLocalAddr | read-write | current | Last MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.5.3 | ScalarmmForwardingTable-Rule5-FirstRemoteAddr | read-write | current | First MODBUS TCP ID field (remote serial address) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.5.4 | ScalarmmForwardingTable-Rule5-SlaveIpAddrIncrement | read-write | current | 1 = last byte of IP address fixed 2 = last byte of IP address variable [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.5.5 | ScalarmmForwardingTable-Rule5-SlaveIpAddr | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.6 | NodemodbusMasterForwardingTable-Rule6 | |||
| 1.3.6.1.4.1.28097.1.6.6.3.6.1 | ScalarmmForwardingTable-Rule6-FirstLocalAddr | read-write | current | First MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.6.2 | ScalarmmForwardingTable-Rule6-LastLocalAddr | read-write | current | Last MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.6.3 | ScalarmmForwardingTable-Rule6-FirstRemoteAddr | read-write | current | First MODBUS TCP ID field (remote serial address) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.6.4 | ScalarmmForwardingTable-Rule6-SlaveIpAddrIncrement | read-write | current | 1 = last byte of IP address fixed 2 = last byte of IP address variable [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.6.5 | ScalarmmForwardingTable-Rule6-SlaveIpAddr | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.7 | NodemodbusMasterForwardingTable-Rule7 | |||
| 1.3.6.1.4.1.28097.1.6.6.3.7.1 | ScalarmmForwardingTable-Rule7-FirstLocalAddr | read-write | current | First MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.7.2 | ScalarmmForwardingTable-Rule7-LastLocalAddr | read-write | current | Last MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.7.3 | ScalarmmForwardingTable-Rule7-FirstRemoteAddr | read-write | current | First MODBUS TCP ID field (remote serial address) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.7.4 | ScalarmmForwardingTable-Rule7-SlaveIpAddrIncrement | read-write | current | 1 = last byte of IP address fixed 2 = last byte of IP address variable [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.7.5 | ScalarmmForwardingTable-Rule7-SlaveIpAddr | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.8 | NodemodbusMasterForwardingTable-Rule8 | |||
| 1.3.6.1.4.1.28097.1.6.6.3.8.1 | ScalarmmForwardingTable-Rule8-FirstLocalAddr | read-write | current | First MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.8.2 | ScalarmmForwardingTable-Rule8-LastLocalAddr | read-write | current | Last MODBUS serial address (local) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.8.3 | ScalarmmForwardingTable-Rule8-FirstRemoteAddr | read-write | current | First MODBUS TCP ID field (remote serial address) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.8.4 | ScalarmmForwardingTable-Rule8-SlaveIpAddrIncrement | read-write | current | 1 = last byte of IP address fixed 2 = last byte of IP address variable [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.6.3.8.5 | ScalarmmForwardingTable-Rule8-SlaveIpAddr | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.7 | NodeserialServiceTcpRawPortServer | |||
| 1.3.6.1.4.1.28097.1.6.7.1 | NodetcpRawServerSerialExtraConfig | |||
| 1.3.6.1.4.1.28097.1.6.7.1.1 | ScalartrsExtraConfigDTR | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.7.1.2 | ScalartrsExtraConfigRTS | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.7.1.3 | ScalartrsExtraConfigDSR | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.7.1.4 | ScalartrsExtraConfigCTS | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.7.1.5 | ScalartrsExtraConfigDCD | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.7.1.6 | ScalartrsExtraConfigXonXoff | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8 | NodeserialServiceTcpRawPortClient | |||
| 1.3.6.1.4.1.28097.1.6.8.1 | NodetcpRawClientSerialExtraConfig | |||
| 1.3.6.1.4.1.28097.1.6.8.1.1 | ScalartrcExtraConfigDTR | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.1.2 | ScalartrcExtraConfigRTS | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.1.4 | ScalartrcExtraConfigCTS | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.1.5 | ScalartrcExtraConfigDCD | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.1.6 | ScalartrcExtraConfigXonXoff | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.4 | ScalartcpRawClientConnectionTimeout | read-write | current | How long before we give up trying to call a server. 0 means indefinitely. [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.5 | ScalartcpRawClientPollPeriode | read-write | current | How long we wait between two scans of the servers list (in case no server is available). [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.6 | ScalartcpRawClientDSRUse | read-write | current | How the DSR pin causes server calls and connection terminations [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7 | NodetcpRawClientRemoteServers | |||
| 1.3.6.1.4.1.28097.1.6.8.7.1 | NodetcpRawClientServer1 | |||
| 1.3.6.1.4.1.28097.1.6.8.7.1.1 | ScalartcpRawClienServer1-IpAddress | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.1.2 | ScalartcpRawclientServer1-TcpPort | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.2 | NodetcpRawClientServer2 | |||
| 1.3.6.1.4.1.28097.1.6.8.7.2.1 | ScalartcpRawclientServer2-IpAddress | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.2.2 | ScalartcpRawclientServer2-TcpPort | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.3 | NodetcpRawClientServer3 | |||
| 1.3.6.1.4.1.28097.1.6.8.7.3.1 | ScalartcpRawclientServer3-IpAddress | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.3.2 | ScalartcpRawclientServer3-TcpPort | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.4 | NodetcpRawClientServer4 | |||
| 1.3.6.1.4.1.28097.1.6.8.7.4.1 | ScalartcpRawclientServer4-IpAddress | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.4.2 | ScalartcpRawclientServer4-TcpPort | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.5 | NodetcpRawClientServer5 | |||
| 1.3.6.1.4.1.28097.1.6.8.7.5.1 | ScalartcpRawclientServer5-IpAddress | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.5.2 | ScalartcpRawclientServer5-TcpPort | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.6 | NodetcpRawClientServer6 | |||
| 1.3.6.1.4.1.28097.1.6.8.7.6.1 | ScalartcpRawclientServer6-IpAddress | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.6.2 | ScalartcpRawclientServer6-TcpPort | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.7 | NodetcpRawClientServer7 | |||
| 1.3.6.1.4.1.28097.1.6.8.7.7.1 | ScalartcpRawclientServer7-IpAddress | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.7.2 | ScalartcpRawclientServer7-TcpPort | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.8 | NodetcpRawClientServer8 | |||
| 1.3.6.1.4.1.28097.1.6.8.7.8.1 | ScalartcpRawclientServer8-IpAddress | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.8.7.8.2 | ScalartcpRawclientServer8-TcpPort | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.9 | NodeserialServiceUdpRawPortServer | |||
| 1.3.6.1.4.1.28097.1.6.9.1 | NodeudpRawServerSerialExtraConfig | |||
| 1.3.6.1.4.1.28097.1.6.9.1.1 | ScalarursExtraConfigDTR | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.9.1.2 | ScalarursExtraConfigRTS | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.9.1.3 | ScalarursExtraConfigCTS | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.9.1.4 | ScalarursExtraConfigXonXoff | read-write | current | [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.9.2 | ScalarudpRawServerRemoteIP | read-write | current | IP address of the remote network device, to which we send data. Using IP address 255.255.255.255 allows multidrop communication [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.1.6.9.3 | ScalarudpRawServerRemotePort | read-write | current | UDP port of the remote network device, used as a destination UDP port when we send data to remote devices on the network. If 0, local port is used. [FW:E2080.A… |
| 1.3.6.1.4.1.28097.1.6.9.4 | ScalarudpRawServerLocalPort | read-write | current | Our receiving UDP port (remote devices on the network use this destination to send us data) [FW:E2080.AC.1-Serial:5.10.0] |
| 1.3.6.1.4.1.28097.2 | NodeacksysInternals | |||
| 1.3.6.1.4.1.28097.2.1 | ScalarinternalUniqueID | read-only | current | Returns a unique product ID for NDM [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.2.2 | ScalarinternalSerial | read-only | current | Returns the motherboard serial number [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.2.3 | ScalarinternalWlanChange | read-only | current | Last wlan table change pseudotime [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.2.4 | ScalarinternalRadioChange | read-only | current | Last radio table change pseudotime [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.2.5 | ScalarinternalSerialTest | read-write | current | Start the serial test [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.2.6 | ScalarinternalSerialTestResult | read-only | current | Read the serial test result [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.2.7 | ScalarinternalAlarmSwitch | read-write | current | Set ou unset the alarm switch [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.2.8 | ScalarinternalDigitalInput | read-only | current | Read the digital input [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.3 | ScalaracksysProductID | read-only | current | Return the product Id code. The m340-wc is also kown as pmxnow0300. [FW:E2080.AC.1:5.52.0] [FW:E2080.AC.1-Serial:5.10.0] [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.4 | Nodec-key-management | |||
| 1.3.6.1.4.1.28097.4.1 | ScalarckeyManagementCopySettingTo | read-write | current | Write 1 to copy the current settings to the C-KEY. After this action, all previous data in the C-KEY are lost. [FW:E2080.AC.1:5.52.0] [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.4.2 | ScalarckeyManagementCopySettingFrom | read-write | current | Write 1 to copy the product settings from the C-KEY. On WLn series, this will reboot the product. [FW:E2080.AC.1:5.52.0] [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.4.3 | ScalarckeyManagementErase | read-write | current | Write 1 to erase the C-KEY. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.4.4 | ScalarckeyManagementStatus | read-only | current | Read the C-Key status [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.4.5 | ScalarckeyManagementIgnoreSetting | read-write | current | Write 2(enable) to disallow configuration loading from C-Key at startup. Write 1(disable) to allow configuration loading from C-Key at startup. [FW:E2148.AC.1:… |
| 1.3.6.1.4.1.28097.4.6 | ScalarckeyManagementDisableLed | read-write | current | Write 2(enable) to make the C-Key status red LED stayed off. Write 1(disable) to use the C-Key status red LED as usal. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.4.7 | ScalarckeyManagementTest | read-write | current | Write 1 to start the C-Key auto-test. Warning, this test will erase the whole C-Key. This OID is reserved for ACKSYS production. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.4.8 | ScalarckeyManagementTestResult | read-only | current | Read the C-Key test results This OID is reserved for ACKSYS production. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.5 | NodealarmSettings | |||
| 1.3.6.1.4.1.28097.5.1 | ScalaralarmSettingsTest | read-write | current | Allow to get and set the alarm output status. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.2 | NodealarmSettingsPower1Down | |||
| 1.3.6.1.4.1.28097.5.2.1 | ScalaralarmSettingsPower1DownEnable | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.2.2 | ScalaralarmSettingsPower1DownEnableAutomaticReset | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.2.3 | ScalaralarmSettingsPower1DownStatus | read-write | current | Read to know the alarm source status (disable / enable ) Write 3 to acknowledge the alarm source. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.3 | NodealarmSettingsPower2Down | |||
| 1.3.6.1.4.1.28097.5.3.1 | ScalaralarmSettingsPower2DownEnable | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.3.2 | ScalaralarmSettingsPower2DownEnableAutomaticReset | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.3.3 | ScalaralarmSettingsPower2DownStatus | read-write | current | Read to know the alarm source status (disable / enable ) Write 3 to acknowledge the alarm source. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.4 | NodealarmSettingsLan1Down | |||
| 1.3.6.1.4.1.28097.5.4.1 | ScalaralarmSettingsLan1DownEnable | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.4.2 | ScalaralarmSettingsLan1DownEnableAutomaticReset | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.4.3 | ScalaralarmSettingsLan1DownStatus | read-write | current | Read to know the alarm source status (disable / enable ) Write 3 to acknowledge the alarm source. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.5 | NodealarmSettingsLan2Down | |||
| 1.3.6.1.4.1.28097.5.5.1 | ScalaralarmSettingsLan2DownEnable | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.5.2 | ScalaralarmSettingsLan2DownEnableAutomaticReset | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.5.3 | ScalaralarmSettingsLan2DownStatus | read-write | current | Read to know the alarm source status (disable / enable ) Write 3 to acknowledge the alarm source. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.6 | NodealarmSettingsLan3Down | |||
| 1.3.6.1.4.1.28097.5.6.1 | ScalaralarmSettingsLan3DownEnable | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.6.2 | ScalaralarmSettingsLan3DownEnableAutomaticReset | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.6.3 | ScalaralarmSettingsLan3DownStatus | read-write | current | Read to know the alarm source status (disable / enable ) Write 3 to acknowledge the alarm source. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.7 | NodealarmSettingsLan4Down | |||
| 1.3.6.1.4.1.28097.5.7.1 | ScalaralarmSettingsLan4DownEnable | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.7.2 | ScalaralarmSettingsLan4DownEnableAutomaticReset | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.7.3 | ScalaralarmSettingsLan4DownStatus | read-write | current | Read to know the alarm source status (disable / enable ) Write 3 to acknowledge the alarm source. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.8 | NodealarmSettingsLan5Down | |||
| 1.3.6.1.4.1.28097.5.8.1 | ScalaralarmSettingsLan5DownEnable | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.8.2 | ScalaralarmSettingsLan5DownEnableAutomaticReset | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.8.3 | ScalaralarmSettingsLan5DownStatus | read-write | current | Read to know the alarm source status (disable / enable ) Write 3 to acknowledge the alarm source. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.9 | NodealarmSettingsLan6Down | |||
| 1.3.6.1.4.1.28097.5.9.1 | ScalaralarmSettingsLan6DownEnable | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.9.2 | ScalaralarmSettingsLan6DownEnableAutomaticReset | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.9.3 | ScalaralarmSettingsLan6DownStatus | read-write | current | Read to know the alarm source status (disable / enable ) Write 3 to acknowledge the alarm source. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.10 | NodealarmSettingsLan7Down | |||
| 1.3.6.1.4.1.28097.5.10.1 | ScalaralarmSettingsLan7DownEnable | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.10.2 | ScalaralarmSettingsLan7DownEnableAutomaticReset | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.10.3 | ScalaralarmSettingsLan7DownStatus | read-write | current | Read to know the alarm source status (disable / enable ) Write 3 to acknowledge the alarm source. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.11 | NodealarmSettingsLan8Down | |||
| 1.3.6.1.4.1.28097.5.11.1 | ScalaralarmSettingsLan8DownEnable | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.11.2 | ScalaralarmSettingsLan8DownEnableAutomaticReset | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.11.3 | ScalaralarmSettingsLan8DownStatus | read-write | current | Read to know the alarm source status (disable / enable ) Write 3 to acknowledge the alarm source. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.12 | NodealarmSettingsWLANDown | |||
| 1.3.6.1.4.1.28097.5.12.1 | ScalaralarmSettingsWLANDownEnable | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.12.2 | ScalaralarmSettingsWLANDownEnableAutomaticReset | read-write | current | [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.5.12.3 | ScalaralarmSettingsWLANDownStatus | read-write | current | Read to know the alarm source status (disable / enable ) Write 3 to acknowledge the alarm source. [FW:E2080.AC.1:5.52.0] |
| 1.3.6.1.4.1.28097.6 | NodepowerStatus | |||
| 1.3.6.1.4.1.28097.6.1 | ScalarpowerStatus-PW1-state | read-only | current | Power 1 state [FW:E2080.AC.1:5.52.0] [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.6.2 | ScalarpowerStatus-PW2-state | read-only | current | Power 2 state [FW:E2080.AC.1:5.52.0] [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.7 | NodenetworkStatus | |||
| 1.3.6.1.4.1.28097.7.1 | TablestatusIpSubnetTable | not-accessible | current | A table that contains information of logical networks (level 3). [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.7.1.1 | RowstatusIpSubnetEntry | not-accessible | current | A table that contains network information. |
| 1.3.6.1.4.1.28097.7.1.1.1 | ColumnstatusIpSubnetIndex | read-only | current | Network index |
| 1.3.6.1.4.1.28097.7.1.1.2 | ColumnstatusIpSubnetName | read-only | current | Network interface name |
| 1.3.6.1.4.1.28097.7.1.1.3 | ColumnstatusIpSubnetLabel | read-only | current | Network friendly name |
| 1.3.6.1.4.1.28097.7.1.1.4 | ColumnstatusIpSubnetIfIndex | read-only | current | Network kernel index |
| 1.3.6.1.4.1.28097.7.1.1.5 | ColumnstatusIpSubnetAddrMode | read-only | current | Ip address protocol of this network |
| 1.3.6.1.4.1.28097.7.1.1.6 | ColumnstatusIpSubnetIPv4Addr | read-only | current | Current IPv4 address of this network |
| 1.3.6.1.4.1.28097.7.1.1.7 | ColumnstatusIpSubnetIPv4Mask | read-only | current | Current IPv4 subnet mask of this network |
| 1.3.6.1.4.1.28097.7.1.1.8 | ColumnstatusIpSubnetDNS | read-only | current | Space-separated list of DNS IP addresses |
| 1.3.6.1.4.1.28097.7.1.1.9 | ColumnstatusIpSubnetMember | read-only | current | Space-separated list that contains name of interfaces related to this network |
| 1.3.6.1.4.1.28097.7.1.1.10 | ColumnstatusIpSubnetMemberIndex | read-only | current | Space-separated list that contains kernel index of interfaces related to this network |
| 1.3.6.1.4.1.28097.7.2 | TablestatusIfWlanTable | not-accessible | current | List of Wi-Fi service sets (ESSID, ISSID) with an IP address [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.7.2.1 | RowstatusIfWlanEntry | not-accessible | current | Details about a Wi-Fi service set |
| 1.3.6.1.4.1.28097.7.2.1.1 | ColumnstatusIfWlanIndex | read-only | current | Wlan index |
| 1.3.6.1.4.1.28097.7.2.1.2 | ColumnstatusIfWlanSSID | read-only | current | SSID string |
| 1.3.6.1.4.1.28097.7.2.1.3 | ColumnstatusIfWlanMode | read-only | current | STA role |
| 1.3.6.1.4.1.28097.7.2.1.4 | ColumnstatusIfWlanBand | read-only | current | Wlan band/modulation type mix |
| 1.3.6.1.4.1.28097.7.2.1.5 | ColumnstatusIfWlanChannel | read-only | current | Wlan channel (frequency span index): -1 channel indicates that the product is searching for a channel |
| 1.3.6.1.4.1.28097.7.2.1.6 | ColumnstatusIfWlanFrequency | read-only | current | Radio frequency: 0 frequency indicates that the product is searching for a radio frequency |
| 1.3.6.1.4.1.28097.7.2.1.7 | ColumnstatusIfWlanEnable | read-only | current | Operational state |
| 1.3.6.1.4.1.28097.7.2.1.8 | ColumnstatusIfWlanPhy | read-only | current | PHY index for this wlan |
| 1.3.6.1.4.1.28097.7.2.1.9 | ColumnstatusIfWlanSecurityMode | read-only | current | Security policy |
| 1.3.6.1.4.1.28097.7.2.1.10 | ColumnstatusIfWlanWpaVersion | read-only | current | WPA version (version 1 is deprecated) |
| 1.3.6.1.4.1.28097.7.2.1.11 | ColumnstatusIfWlanNPeers | read-only | current | Number of peer clients |
| 1.3.6.1.4.1.28097.7.2.1.12 | ColumnstatusIfWlanQuality | read-only | current | Radio link quality |
| 1.3.6.1.4.1.28097.7.2.1.13 | ColumnstatusIfWlanBssid | read-only | current | BSSID |
| 1.3.6.1.4.1.28097.7.2.1.14 | ColumnstatusIfWlanState | read-only | current | Connection state |
| 1.3.6.1.4.1.28097.7.2.1.15 | ColumnstatusIfStaFastBSSTransitionActivated | read-only | current | 802.11r support (dot11FastBSSTransitionActivated) |
| 1.3.6.1.4.1.28097.7.2.1.16 | ColumnstatusIfWlanBeaconSignalAvg | read-only | current | Signal level average in dBm of the last few beacons received Before WaveOS V2.8.0.1, this OID gives the last beacon signal After WaveOS V2.8.0.1, this OID give… |
| 1.3.6.1.4.1.28097.7.2.1.17 | ColumnstatusIfWlanNoise | read-only | current | Noise level in dBm |
| 1.3.6.1.4.1.28097.7.2.1.18 | ColumnstatusIfWlanWpaCipher | read-only | current | WPA cipher |
| 1.3.6.1.4.1.28097.7.2.1.19 | ColumnstatusIfWlanWpaPreSharedKey | read-only | current | WPA PSK pre-shared key |
| 1.3.6.1.4.1.28097.7.2.1.20 | ColumnstatusIfWlanName | read-only | current | Wireless interface name [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.7.2.1.21 | ColumnstatusIfWlanIfIndex | read-only | current | Wireless interface kernel index [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.7.3 | TablestatusPhyWifiTable | not-accessible | current | This table contains information about Wi-Fi adapters. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.7.3.1 | RowstatusPhyWifiEntry | not-accessible | current | Details about a Wi-Fi service set |
| 1.3.6.1.4.1.28097.7.3.1.1 | ColumnstatusPhyWifiIndex | read-only | current | Radio device index |
| 1.3.6.1.4.1.28097.7.3.1.2 | ColumnstatusPhyWifiLabel | read-only | current | Friendly name |
| 1.3.6.1.4.1.28097.7.3.1.3 | ColumnstatusPhyWifiEnable | read-only | current | Operational state |
| 1.3.6.1.4.1.28097.7.3.1.4 | ColumnstatusPhyWifiName | read-only | current | Friendly name |
| 1.3.6.1.4.1.28097.7.3.1.5 | ColumnstatusPhyWifiClusterMode | read-only | current | Cluster mode, empty for none, 'dualscan' for data/scan separation |
| 1.3.6.1.4.1.28097.7.3.1.6 | ColumnstatusPhyWifiClusterList | read-only | current | List of device names in the cluster, e.g. 'radio0 radio1' |
| 1.3.6.1.4.1.28097.7.3.1.7 | ColumnstatusPhyWifiClusterArgs | read-only | current | Cluster params for this device. For 'dualscan' mode, one device must be set to 'scan', the others in the cluster must be set to 'data'. |
| 1.3.6.1.4.1.28097.7.3.1.8 | ColumnstatusPhyWifiMAC | read-only | current | MAC address of the radio device [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.7.3.1.9 | ColumnstatusPhyWifiWids | read-only | current | WIDS services state. 0: not started. 1: currently monitoring for rogue APs. [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.7.4 | TablestatusPhyWifiScanTable | not-accessible | current | List of Wi-Fi access points devices around [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.7.4.1 | RowstatusPhyWifiScanEntry | not-accessible | current | Details about a Wi-Fi access point |
| 1.3.6.1.4.1.28097.7.4.1.1 | ColumnstatusPhyWifiScanTableIndex | read-only | current | Radio device index |
| 1.3.6.1.4.1.28097.7.4.1.2 | ColumnstatusPhyWifiScanSSID | read-only | current | Radio device SSID |
| 1.3.6.1.4.1.28097.7.4.1.3 | ColumnstatusPhyWifiScanSignal | read-only | current | Radio device signal power in dBm |
| 1.3.6.1.4.1.28097.7.4.1.4 | ColumnstatusPhyWifiScanFreq | read-only | current | Radio device central frequency (in MHz) |
| 1.3.6.1.4.1.28097.7.4.1.5 | ColumnstatusPhyWifiScanMode | read-only | current | Radio device mode |
| 1.3.6.1.4.1.28097.7.4.1.6 | ColumnstatusPhyWifiScanSecurity | read-only | current | Radio device mode |
| 1.3.6.1.4.1.28097.7.4.1.7 | ColumnstatusPhyWifiScanBssid | read-only | current | Radio device bssid |
| 1.3.6.1.4.1.28097.7.4.1.8 | ColumnstatusPhyWifiScanPhyNum | read-only | current | Scan phy index |
| 1.3.6.1.4.1.28097.7.4.1.9 | ColumnstatusPhyWifiScanChWidth | read-only | current | Radio device channel width [FW:E2148.AC.1:4.8.0.1] |
| 1.3.6.1.4.1.28097.7.5 | ScalarstatusPhyWifiScanTableStart | read-write | current | Write (any value) to start a scan. Poll the statusPhyWifiScanUpdateTbl OID to know the status of the current scan : inprogress or available [FW:E2148.AC.1:2.8.… |
| 1.3.6.1.4.1.28097.7.6 | ScalarstatusPhyWifiScanUpdateTbl | read-write | current | Returns inprogress if current scan isn't finished yet. Returns available if the current scan results are available. In this case, the ScanTable will be updated… |
| 1.3.6.1.4.1.28097.7.7 | TablestatusSpanningTreeTable | not-accessible | current | A table that contains information related to STP about every bridge [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.7.7.1 | RowstatusSpanningTreeEntry | not-accessible | current | A list of objects containing information for each Bridge about the Spanning Tree Protocol for that Bridge. |
| 1.3.6.1.4.1.28097.7.7.1.1 | ColumnstatusSpanningTreeBridgeName | read-only | current | Symbolic name of the bridge for which this entry contains Spanning Tree Protocol management information. Referred to in the general Interfaces table. |
| 1.3.6.1.4.1.28097.7.7.1.2 | ColumnstatusSpanningTreeNetworkLabel | read-only | current | The network label that contains the current bridge. |
| 1.3.6.1.4.1.28097.7.7.1.3 | ColumnstatusSpanningTreeBridgeId | read-only | current | The bridge Id. It is made up using the bridge priority and the base MAC address of the bridge. |
| 1.3.6.1.4.1.28097.7.7.1.4 | ColumnstatusSpanningTreeDesignatedRoot | read-only | current | Root Bridge for the Spanning tree. It is made up using the bridge priority and the base MAC address of the bridge. |
| 1.3.6.1.4.1.28097.7.7.1.5 | ColumnstatusSpanningTreeRootPort | read-only | current | The root port name of the current bridge. none is set if there is no root port in the bridge |
| 1.3.6.1.4.1.28097.7.8 | TablestatusSpanningTreePortTable | not-accessible | current | A table that contains port-specific information for the Spanning Tree Protocol. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.7.8.1 | RowstatusSpanningTreePortEntry | not-accessible | current | A list of objects containing information maintained by every port about the Spanning Tree Protocol state for that port. |
| 1.3.6.1.4.1.28097.7.8.1.1 | ColumnstatusSpanningTreePortBridgeName | read-only | current | Symbolic name of the bridge for which this entry contains Spanning Tree Protocol management information. Referred to in the general Interfaces table. |
| 1.3.6.1.4.1.28097.7.8.1.2 | ColumnstatusSpanningTreePortNetworkLabel | read-only | current | The network label that contains the current bridge. |
| 1.3.6.1.4.1.28097.7.8.1.3 | ColumnstatusSpanningTreePortName | read-only | current | The name of the port for which this entry contains Spanning Tree Protocol management information. Referred to in the general Interfaces table. |
| 1.3.6.1.4.1.28097.7.8.1.4 | ColumnstatusSpanningTreePortLabel | read-only | current | Port label for the specified port. |
| 1.3.6.1.4.1.28097.7.8.1.5 | ColumnstatusSpanningTreePortId | read-only | current | Port identifier for the specified port, it is made up from the port priority and the interface number of the port. |
| 1.3.6.1.4.1.28097.7.8.1.6 | ColumnstatusSpanningTreePortRole | read-only | current | The port's current role in the Spanning Tree |
| 1.3.6.1.4.1.28097.7.8.1.7 | ColumnstatusSpanningTreePortState | read-only | current | The port's current state in the Spanning Tree |
| 1.3.6.1.4.1.28097.7.8.1.8 | ColumnstatusSpanningTreePortPathCost | read-only | current | The contribution of this port to the path cost of paths towards the spanning tree root which include this port. |
| 1.3.6.1.4.1.28097.7.8.1.9 | ColumnstatusSpanningTreePortDesignatedRoot | read-only | current | The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the po… |
| 1.3.6.1.4.1.28097.7.8.1.10 | ColumnstatusSpanningTreePortDesignatedCost | read-only | current | The path cost of the Designated Port of the segment connected to this port. |
| 1.3.6.1.4.1.28097.7.8.1.11 | ColumnstatusSpanningTreePortDesignatedBridge | read-only | current | The Bridge Identifier of the Bridge that this port considers to be the Designated Bridge for this port's segment. |
| 1.3.6.1.4.1.28097.7.8.1.12 | ColumnstatusSpanningTreePortDesignatedPort | read-only | current | The Port Identifier of the port on the Designated Bridge for this port's segment. |
| 1.3.6.1.4.1.28097.7.8.1.13 | ColumnstatusSpanningTreePortOperEdgePort | read-only | current | The operational value of the Edge Port parameter. A value of true(1) indicates that this port should be assumed as an edge-port, and a value of false(2) indica… |
| 1.3.6.1.4.1.28097.7.8.1.14 | ColumnstatusSpanningTreePortOperPointToPoint | read-only | current | The operational value of the Point to Point parameter. A value of true(1) indicates that this port is point to point, otherwise set to false(2) |
| 1.3.6.1.4.1.28097.7.9 | TablestatusAssociationTable | not-accessible | current | A table that contains information of associated stations. [FW:E2148.AC.1:3.12.0.1] |
| 1.3.6.1.4.1.28097.7.9.1 | RowstatusAssociationEntry | not-accessible | current | A table that contains information of associated stations. |
| 1.3.6.1.4.1.28097.7.9.1.1 | ColumnstatusAssociationIndex | read-only | current | Associated station index |
| 1.3.6.1.4.1.28097.7.9.1.2 | ColumnstatusAssociationMacAddr | read-only | current | MAC address of the associated station |
| 1.3.6.1.4.1.28097.7.9.1.3 | ColumnstatusAssociationSSID | read-only | current | SSID of the associated station |
| 1.3.6.1.4.1.28097.7.9.1.4 | ColumnstatusAssociationBSSID | read-only | current | BSSID of the associated station |
| 1.3.6.1.4.1.28097.7.9.1.5 | ColumnstatusAssociationPhy | read-only | current | radio name of the radio that the station connects |
| 1.3.6.1.4.1.28097.7.9.1.6 | ColumnstatusAssociationSignaldBm | read-only | current | RSSI level in dBm |
| 1.3.6.1.4.1.28097.7.9.1.7 | ColumnstatusAssociationNoisedBm | read-only | current | Noise level in dBm |
| 1.3.6.1.4.1.28097.7.9.1.8 | ColumnstatusAssociationSNR | read-only | current | Signal-to-noise ratio |
| 1.3.6.1.4.1.28097.7.9.1.9 | ColumnstatusAssociationWlanIndex | read-only | current | Index of the role that the station connects [FW:E2148.AC.1:3.12.9.1] |
| 1.3.6.1.4.1.28097.7.9.1.10 | ColumnstatusAssociationSecurityMode | read-only | current | Security policy [FW:E2148.CA.1:4.8.0.1-R3] |
| 1.3.6.1.4.1.28097.7.10 | TablestatusPhyLanTable | not-accessible | current | A table that contains information of physical ethernet adapter. [FW:E2148.AC.1:3.12.0.1] |
| 1.3.6.1.4.1.28097.7.10.1 | RowstatusPhyLanEntry | not-accessible | current | A table that contains information of physical ethernet adapter. |
| 1.3.6.1.4.1.28097.7.10.1.1 | ColumnstatusPhyLanIndex | read-only | current | Physical ethernet index |
| 1.3.6.1.4.1.28097.7.10.1.2 | ColumnstatusPhyLanName | read-only | current | Physical ethernet adapter interface name |
| 1.3.6.1.4.1.28097.7.10.1.3 | ColumnstatusPhyLanLabel | read-only | current | Physical ethernet adapter friendly name |
| 1.3.6.1.4.1.28097.7.10.1.4 | ColumnstatusPhyLanIfIndex | read-only | current | Physical ethernet kernel index |
| 1.3.6.1.4.1.28097.7.11 | TablestatusMeshSurveyTable | not-accessible | current | A table that contains information of mesh survey. [FW:E2148.AC.1:3.12.9.1] |
| 1.3.6.1.4.1.28097.7.11.1 | RowstatusMeshSurveyEntry | not-accessible | current | A table that contains information of mesh survey. |
| 1.3.6.1.4.1.28097.7.11.1.1 | ColumnstatusMeshSurveyIndex | read-only | current | Mesh survey index |
| 1.3.6.1.4.1.28097.7.11.1.2 | ColumnstatusMeshSurveyDstMacAddr | read-only | current | Destination MAC address of the mesh path |
| 1.3.6.1.4.1.28097.7.11.1.3 | ColumnstatusMeshSurveyNextHopMacAddr | read-only | current | MAC address of the next mesh point to reach destination MAC address |
| 1.3.6.1.4.1.28097.7.11.1.4 | ColumnstatusMeshSurveyPhy | read-only | current | Radio name of the mesh path |
| 1.3.6.1.4.1.28097.7.11.1.5 | ColumnstatusMeshSurveyMetric | read-only | current | Total cost of the mesh path |
| 1.3.6.1.4.1.28097.7.11.1.6 | ColumnstatusMeshSurveyDiscoveryTimeout | read-only | current | Current discovery timeout for the mesh path |
| 1.3.6.1.4.1.28097.7.11.1.7 | ColumnstatusMeshSurveyDiscoveryRetries | read-only | current | The number of discovery retries |
| 1.3.6.1.4.1.28097.7.11.1.8 | ColumnstatusMeshSurveyStateActive | read-only | current | State Active: a value of true(1) indicates that the mesh path can be used for forwording |
| 1.3.6.1.4.1.28097.7.11.1.9 | ColumnstatusMeshSurveyStateResolving | read-only | current | State Resolving: a value of true(1) indicates that the discovery process for the mesh path is running |
| 1.3.6.1.4.1.28097.7.11.1.10 | ColumnstatusMeshSurveyStateDSNValid | read-only | current | State DSN Valid: a value of true(1) indicates that the mesh path contains a valid destination sequence number |
| 1.3.6.1.4.1.28097.7.11.1.11 | ColumnstatusMeshSurveyStateFixed | read-only | current | State Fixed: a value of true(1) indicates that the status of the mesh path is fixed |
| 1.3.6.1.4.1.28097.7.11.1.12 | ColumnstatusMeshSurveyStateResolved | read-only | current | State Resolved: a value of true(1) indicates that the discovery process ends successfully |
| 1.3.6.1.4.1.28097.7.11.1.13 | ColumnstatusMeshSurveyMeshId | read-only | current | Mesh ID string of the mesh path |
| 1.3.6.1.4.1.28097.7.11.1.14 | ColumnstatusMeshSurveyWlanIndex | read-only | current | Wlan index of the mesh path |
| 1.3.6.1.4.1.28097.7.12 | TablestatusPhyCellTable | not-accessible | current | This table contains information about cellular adapters. [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1 | RowstatusPhyCellEntry | not-accessible | current | Details about a cellular adapter [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.1 | ColumnstatusPhyCellIndex | read-only | current | Cellular adapter index [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.2 | ColumnstatusPhyCellLabel | read-only | current | The label physically identifying the antennas set on the device [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.3 | ColumnstatusPhyCellFriendlyName | read-only | current | Friendly name for this cellular adapter [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.4 | ColumnstatusPhyCellEnable | read-only | current | Administrative state [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.5 | ColumnstatusPhyCellIMEI | read-only | current | Adapter IMEI [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.6 | ColumnstatusPhyCellModel | read-only | current | Manufacturer adapter ID [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.7 | ColumnstatusPhyCellName | read-only | current | Symbolic identifier for the adapter [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.8 | ColumnstatusPhyCellSimSelected | read-only | current | SIM card currently in use (1 or 2, 0=unknown) [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.9 | ColumnstatusPhyCellSimState | read-only | current | SIM state, see 3GPP TS27.007 +CPIN [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.10 | ColumnstatusPhyCellSimIMSI | read-only | current | Subscriber identity (IMSI) [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.11 | ColumnstatusPhyCellAttachMode | read-only | current | Network registration state, see 3GPP TS27.007 +CREG [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.12 | ColumnstatusPhyCellOperator | read-only | current | Telecom operator name [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.13 | ColumnstatusPhyCellMcc | read-only | current | Mobile Country Code [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.14 | ColumnstatusPhyCellMnc | read-only | current | Mobile Network (Operator) Code [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.15 | ColumnstatusPhyCellBaseLAC | read-only | current | Location Area Code [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.16 | ColumnstatusPhyCellBaseCID | read-only | current | Cell ID [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.17 | ColumnstatusPhyCellRegistrationClass | read-only | current | Registration class (gsm, cdma) [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.18 | ColumnstatusPhyCellAccessTech | read-only | current | Access Technology, see 3GPP TS27.007 +CREG [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.19 | ColumnstatusPhyCellBandName | read-only | current | Radio band [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.20 | ColumnstatusPhyCellARFCN | read-only | current | Channel (ARFCN) [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.21 | ColumnstatusPhyCellRSSI | read-only | current | Signal quality (RSSI) [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.12.1.22 | ColumnstatusPhyCellBER | read-only | current | Bit Error Rate Estimator (see 3GPP TS45.008) [FW:E2148.AC.1:3.16.1.1] |
| 1.3.6.1.4.1.28097.7.13 | NodestatusRoaming | |||
| 1.3.6.1.4.1.28097.7.13.1 | ScalarstatusRoamingLeaveLvlMax | read-only | current | When current AP's signal level is above this value, roaming will occur when possible. [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.2 | ScalarstatusRoamingLeaveLvlMin | read-only | current | When current AP's signal level is below this value, roaming will occur when possible. [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.3 | ScalarstatusRoamingRoamLvlMax | read-only | current | When the signal level of an AP in scan result is above this value, it will not be considered as a candidate. [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.4 | ScalarstatusRoamingRoamLvlMin | read-only | current | When the signal level of an AP in scan result is below this value, it will not be considered as a candidate. [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.5 | ScalarstatusRoamingThresHyst | read-only | current | The hysteresis applied in all thresholds [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.6 | ScalarstatusRoamingLeaveBoost | read-only | current | Roaming occurs only if the candidate signal level is above the current AP's plus this value. [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.7 | NodestatusRoamingActiveIf | |||
| 1.3.6.1.4.1.28097.7.13.7.1 | ScalarstatusRoamingActiveIfName | read-only | current | Name of active roaming interface [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.7.2 | ScalarstatusRoamingActiveIfBssid | read-only | current | BSSID of active roaming interface [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.7.3 | ScalarstatusRoamingActiveIfBeaconSignalAvg | read-only | current | Signal level average in dBm of the last few beacons received [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.7.4 | ScalarstatusRoamingActiveIfNoise | read-only | current | Noise level of active roaming interface [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.7.5 | ScalarstatusRoamingActiveIfSwitching | read-only | current | If roaming interface is switching [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.7.6 | ScalarstatusRoamingActiveIfChannel | read-only | current | Wlan channel (frequency span index): -1 channel indicates that the product is searching for a channel [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.7.13.7.7 | ScalarstatusRoamingActiveIfState | read-only | current | Connection state [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.7.13.8 | NodestatusRoamingPassiveIf | |||
| 1.3.6.1.4.1.28097.7.13.8.1 | ScalarstatusRoamingPassiveIfName | read-only | current | Name of passive roaming interface [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.8.2 | ScalarstatusRoamingPassiveIfBssid | read-only | current | BSSID of passive roaming interface [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.8.3 | ScalarstatusRoamingPassiveIfBeaconSignalAvg | read-only | current | Signal level average in dBm of the last few beacons received [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.8.4 | ScalarstatusRoamingPassiveIfNoise | read-only | current | Noise level of passive roaming interface [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.8.5 | ScalarstatusRoamingPassiveIfSwitching | read-only | current | If roaming interface is switching [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.7.13.8.6 | ScalarstatusRoamingPassiveIfChannel | read-only | current | Wlan channel (frequency span index): -1 channel indicates that the product is searching for a channel [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.7.13.8.7 | ScalarstatusRoamingPassiveIfState | read-only | current | Connection state [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.7.13.9 | ScalarstatusRoamingUrgent | read-only | current | PLH algorithm 'Urgent' indication. Disable: normal condition. Enable: the current AP is below the urgent level, and there is no candidate AP complying with the… |
| 1.3.6.1.4.1.28097.8 | NodenetworkConfiguration | |||
| 1.3.6.1.4.1.28097.8.1 | Nodetcpip | |||
| 1.3.6.1.4.1.28097.8.1.1 | TableconfigIpSubnetTable | not-accessible | current | List of network interfaces currently associated with an IP address [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.1.1 | RowconfigIpSubnetEntry | not-accessible | current | Details about an IP address [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.1.1.1 | ColumnconfigIpSubnetName | read-only | current | Interface attached to this subnet |
| 1.3.6.1.4.1.28097.8.1.1.1.2 | ColumnconfigIpSubnetRowStatus | read-create | current | row addition/deletion support [net] |
| 1.3.6.1.4.1.28097.8.1.1.1.3 | ColumnconfigIpAddressMode | read-write | current | Ip address protocol of this subnet |
| 1.3.6.1.4.1.28097.8.1.1.1.4 | ColumnconfigIpSubnetIPv4Addr | read-write | current | IPv4 address given to the interface |
| 1.3.6.1.4.1.28097.8.1.1.1.5 | ColumnconfigIpSubnetIPv4Mask | read-write | current | IPv4 subnet mask |
| 1.3.6.1.4.1.28097.8.1.1.1.6 | ColumnconfigIpSubnetMetric | read-write | current | Subnet metric |
| 1.3.6.1.4.1.28097.8.1.1.1.7 | ColumnconfigIpSubnetDnsList | read-write | current | Space-separated list of DNS IP addresses |
| 1.3.6.1.4.1.28097.8.1.1.1.8 | ColumnconfigIpSubnetInterface | read-write | current | Interface related to this ipSubnet. This field must be left blank for bridge interfaces |
| 1.3.6.1.4.1.28097.8.1.1.1.9 | ColumnconfigIpSubnetIPv4Gateway | read-write | current | IPv4 gateway |
| 1.3.6.1.4.1.28097.8.1.1.1.10 | ColumnconfigIpSubnetFriendlyName | read-write | current | Friendly name of this subnet |
| 1.3.6.1.4.1.28097.8.1.1.1.11 | ColumnconfigIpSubnetBridgeEnable | read-write | current | Write 2 (Enable) to configure this subnet as a bridge type interface: create a bridge over specified interface(s) in this subnet. Write 1 (Disable) to configur… |
| 1.3.6.1.4.1.28097.8.1.1.1.12 | ColumnconfigIpSubnetPersistence | read-write | current | Define the behaviour of the IP layer when the lower interface loses its connection. - When enabled, the IP settings (IP addresses, routes through this interfac… |
| 1.3.6.1.4.1.28097.8.1.1.1.13 | ColumnconfigIpSubnetEnable | read-write | current | Set to Enable to install the layer 3 network. If disabled, this subnet will not be initialized (thus not useable) after the configuration is applied. [FW:E2148… |
| 1.3.6.1.4.1.28097.8.1.1.1.14 | ColumnconfigIpSubnetAutoStart | read-write | current | Define whether, after installation and initialization, the subnet is activated immediately (when configuration is applied) or only when a suitable event happen… |
| 1.3.6.1.4.1.28097.8.1.1.1.15 | ColumnconfigIpSubnetPeerDns | read-write | current | If this subnet is a DHCP client, should the DNS obtained from the DHCP server replace the currently configured one? Set to 'Enable' to give preference to the D… |
| 1.3.6.1.4.1.28097.8.1.1.1.16 | ColumnconfigIpSubnetDefaultRoute | read-write | current | If this subnet is a DHCP client, should the server-provided default route replace the currently configured one? Set to 'Enable' to give preference to the DHCP … |
| 1.3.6.1.4.1.28097.8.1.2 | NodeipFactory | |||
| 1.3.6.1.4.1.28097.8.1.2.1 | Scalarsynfloodprotection | read-write | current | Allow(2)/disallow(1) SYN flood protection. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.2.2 | Scalardropinvalidpacket | read-write | current | Write 2(enable) to allow invalid packetdropping. Write 1(disable) to disallow invalid packetdropping. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.2.3 | TableconfigIpZonesTable | not-accessible | current | List of user defined network zones [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.2.3.1 | RowconfigIpZonesEntry | not-accessible | current | Details about an IpFactory Zone [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.2.3.1.1 | ColumnconfigIpZoneIndex | read-write | current | Zone index |
| 1.3.6.1.4.1.28097.8.1.2.3.1.2 | ColumnconfigIpZoneRowStatus | read-create | current | row addition/deletion support [PF:zone_:1] |
| 1.3.6.1.4.1.28097.8.1.2.3.1.3 | ColumnconfigIpZoneFriendlyName | read-write | current | Friendly name |
| 1.3.6.1.4.1.28097.8.1.2.3.1.4 | ColumnconfigIpZoneNAT | read-write | current | Enable / Disable network address translation |
| 1.3.6.1.4.1.28097.8.1.2.3.1.5 | ColumnconfigIpZoneMSSClamping | read-write | current | Enable / Disable MSS Clamping |
| 1.3.6.1.4.1.28097.8.1.2.3.1.6 | ColumnconfigIpZoneDefaultAcceptancePolicy | read-write | current | Default packet acceptance policy |
| 1.3.6.1.4.1.28097.8.1.2.3.1.7 | ColumnconfigIpZoneRestrictedAddressFamily | read-write | current | Restrict action on the given IP address family. Attention:WaveOS supports only IPV4. |
| 1.3.6.1.4.1.28097.8.1.2.3.1.8 | ColumnconfigIpZoneConnectionTracking | read-write | current | Enable / Disable connection tracking |
| 1.3.6.1.4.1.28097.8.1.2.3.1.9 | ColumnconfigIpZoneLogging | read-write | current | Enable / Disable logging for this zone |
| 1.3.6.1.4.1.28097.8.1.2.3.1.10 | ColumnconfigIpZoneLoggingLimit | read-write | current | Defines the limit of logging messages per unit of time for this zone. This octet string is defined as : N[/T]. Where N is the number of messages and T is one o… |
| 1.3.6.1.4.1.28097.8.1.2.3.1.11 | ColumnconfigIpZoneInterfaces | read-write | current | The (space separated) interface list of network devices using this zone |
| 1.3.6.1.4.1.28097.8.1.2.4 | TableconfigIpNatIpForwardTable | not-accessible | current | List of IP forward rules, allows to redirect the input traffic on one zone to a device on private zone. Attention: This rule can be set when NAT is disabled bu… |
| 1.3.6.1.4.1.28097.8.1.2.4.1 | RowconfigIpNatIpForwardEntry | not-accessible | current | Details about an IP forward rule [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.2.4.1.1 | ColumnconfigIpNatIpForwardIndex | read-write | current | IP forward rule index |
| 1.3.6.1.4.1.28097.8.1.2.4.1.2 | ColumnconfigIpNatIpForwardRowStatus | read-create | current | row addition/deletion support [PF:rule_:1] |
| 1.3.6.1.4.1.28097.8.1.2.4.1.3 | ColumnconfigIpNatIpForwardFriendlyName | read-write | current | Friendly name |
| 1.3.6.1.4.1.28097.8.1.2.4.1.4 | ColumnconfigIpNatIpForwardZoneName | read-write | current | Zone this rule belongs to |
| 1.3.6.1.4.1.28097.8.1.2.4.1.5 | ColumnconfigIpNatIpForwardSrcIp | read-write | current | Source IP |
| 1.3.6.1.4.1.28097.8.1.2.4.1.6 | ColumnconfigIpNatIpForwardProtocol | read-write | current | IP protocol |
| 1.3.6.1.4.1.28097.8.1.2.4.1.7 | ColumnconfigIpNatIpForwardPublicPort | read-write | current | Public port |
| 1.3.6.1.4.1.28097.8.1.2.4.1.8 | ColumnconfigIpNatIpForwardPrivatePort | read-write | current | Private port |
| 1.3.6.1.4.1.28097.8.1.2.4.1.9 | ColumnconfigIpNatIpForwardTargetIp | read-write | current | The destination IP address |
| 1.3.6.1.4.1.28097.8.1.2.5 | TableconfigIpFirewallTable | not-accessible | current | List of ip firewall rules on specified zone [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.2.5.1 | RowconfigIpFirewallEntry | not-accessible | current | Details about an IP firewall rule [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.2.5.1.1 | ColumnconfigIpFirewallIndex | read-write | current | Ip forward rule index |
| 1.3.6.1.4.1.28097.8.1.2.5.1.2 | ColumnconfigIpFirewallRowStatus | read-create | current | row addition/deletion support [PF:rule_:1] |
| 1.3.6.1.4.1.28097.8.1.2.5.1.3 | ColumnconfigIpFirewallZoneName | read-write | current | Zone this rule belongs to |
| 1.3.6.1.4.1.28097.8.1.2.5.1.4 | ColumnconfigIpFirewallProtocol | read-write | current | Transport protocol |
| 1.3.6.1.4.1.28097.8.1.2.5.1.5 | ColumnconfigIpFirewallPort | read-write | current | IP port |
| 1.3.6.1.4.1.28097.8.1.2.5.1.6 | ColumnconfigIpFirewallAction | read-write | current | Action to take when the rule applies |
| 1.3.6.1.4.1.28097.8.1.2.5.1.7 | ColumnconfigIpFirewallDestZone | read-write | current | Destination zone. If left blank, local interface is selected. |
| 1.3.6.1.4.1.28097.8.1.2.5.1.8 | ColumnconfigIpFirewallSrcIP | read-write | current | The source IP of this firewall rule [FW:E2148.AC.1:3.12.8.1] |
| 1.3.6.1.4.1.28097.8.1.2.5.1.9 | ColumnconfigIpFirewallTargetIP | read-write | current | The destination IP of this firewall rule [FW:E2148.AC.1:3.12.8.1] |
| 1.3.6.1.4.1.28097.8.1.2.6 | TableconfigIpRoutesTable | not-accessible | current | List of IP static routes [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.2.6.1 | RowconfigIpRoutesEntry | not-accessible | current | Details about an IP static route [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.2.6.1.1 | ColumnconfigIpRoutesIndex | read-write | current | Static route index |
| 1.3.6.1.4.1.28097.8.1.2.6.1.2 | ColumnconfigIpRoutesRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.8.1.2.6.1.3 | ColumnconfigIpRoutesNetwork | read-write | current | Network this rule is attached to |
| 1.3.6.1.4.1.28097.8.1.2.6.1.4 | ColumnconfigIpRoutesTarget | read-write | current | Target IP or network |
| 1.3.6.1.4.1.28097.8.1.2.6.1.5 | ColumnconfigIpRoutesNetmask | read-write | current | Target network. If target is a network |
| 1.3.6.1.4.1.28097.8.1.2.6.1.6 | ColumnconfigIpRoutesGateway | read-write | current | IP gateway |
| 1.3.6.1.4.1.28097.8.1.2.6.1.7 | ColumnconfigIpRoutesMetric | read-write | current | Packet metric |
| 1.3.6.1.4.1.28097.8.1.2.6.1.8 | ColumnconfigIpRoutesMTU | read-write | current | Packet MTU |
| 1.3.6.1.4.1.28097.8.1.2.7 | TableconfigIpZoneForwardTable | not-accessible | current | List of zone forward rules [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.2.7.1 | RowconfigIpZoneForwardEntry | not-accessible | current | Details about a zone forward rule [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.2.7.1.1 | ColumnconfigIpZoneForwardIndex | read-write | current | Zone forwarding index |
| 1.3.6.1.4.1.28097.8.1.2.7.1.2 | ColumnconfigIpZoneForwardRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.8.1.2.7.1.3 | ColumnconfigIpZoneForwardSrc | read-write | current | Source Zone |
| 1.3.6.1.4.1.28097.8.1.2.7.1.4 | ColumnconfigIpZoneForwardDst | read-write | current | Destination Zone |
| 1.3.6.1.4.1.28097.8.1.2.8 | TableconfigIpDscpTaggingTable | not-accessible | current | List of DSCP tagging rules [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.2.8.1 | RowconfigIpDscpTaggingEntry | not-accessible | current | Details about a DSCP tagging rule [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.1.2.8.1.1 | ColumnconfigIpDscpTaggingIndex | read-write | current | DSCP tagging rule index Enter a memonic name for this rule. Only letters, digits and underscores |
| 1.3.6.1.4.1.28097.8.1.2.8.1.2 | ColumnconfigIpDscpTaggingRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.8.1.2.8.1.3 | ColumnconfigIpDscpTaggingFriendlyName | read-write | current | Rule friendly name |
| 1.3.6.1.4.1.28097.8.1.2.8.1.4 | ColumnconfigIpDscpTaggingProtocol | read-write | current | The protocol filter |
| 1.3.6.1.4.1.28097.8.1.2.8.1.5 | ColumnconfigIpDscpTaggingSrcIP | read-write | current | The source IP filter |
| 1.3.6.1.4.1.28097.8.1.2.8.1.6 | ColumnconfigIpDscpTaggingDstIP | read-write | current | The destination IP filter |
| 1.3.6.1.4.1.28097.8.1.2.8.1.7 | ColumnconfigIpDscpTaggingSrcPort | read-write | current | The source port filter |
| 1.3.6.1.4.1.28097.8.1.2.8.1.8 | ColumnconfigIpDscpTaggingDstPort | read-write | current | The destination port filter |
| 1.3.6.1.4.1.28097.8.1.2.8.1.9 | ColumnconfigIpDscpTaggingDscpValue | read-write | current | The DSCP value applied by this rule |
| 1.3.6.1.4.1.28097.8.2 | Nodenetphy | |||
| 1.3.6.1.4.1.28097.8.2.1 | TableconfigPhyWifiTable | not-accessible | current | List of Wi-Fi radio devices [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.2.1.1 | RowconfigPhyWifiEntry | not-accessible | current | Details about a Wi-Fi service set [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.2.1.1.2 | ColumnconfigPhyWifiName | read-only | current | Symbolic identifier for the radio device |
| 1.3.6.1.4.1.28097.8.2.1.1.3 | ColumnconfigPhyWifiLabel | read-only | current | The label physically identifying the antennas set on the device [phywifi] |
| 1.3.6.1.4.1.28097.8.2.1.1.4 | ColumnconfigPhyWifiMAC | read-only | current | MAC address of the radio device |
| 1.3.6.1.4.1.28097.8.2.1.1.5 | ColumnconfigPhyWifiEnable | read-write | current | Configured state |
| 1.3.6.1.4.1.28097.8.2.1.1.6 | ColumnconfigPhyWifiMode | read-write | current | Configured 802.11 flavor. -1 indicates invalid value. |
| 1.3.6.1.4.1.28097.8.2.1.1.7 | ColumnconfigPhyWifiCountry | read-write | current | Country for regulatory checks on channel/power |
| 1.3.6.1.4.1.28097.8.2.1.1.8 | ColumnconfigPhyWifiChannel | read-write | current | Configured radio channel (frequency span index) A value of 0 indicates that your radio device is configured on multiple channels or automatic channel select. S… |
| 1.3.6.1.4.1.28097.8.2.1.1.9 | ColumnconfigPhyWifiHTMode | read-write | current | 802.11n channel width. Double (40) width is subject to automatic availability checking before use. |
| 1.3.6.1.4.1.28097.8.2.1.1.10 | ColumnconfigPhyWifiTxPowerDBM | read-write | current | Configured radio transmit power limit in dBm. To transmit with the maximum allowed power, use value '-1'. |
| 1.3.6.1.4.1.28097.8.2.1.1.11 | ColumnconfigPhyWifiDistance | read-write | current | Configured maximum distance between AP and stations (meters) |
| 1.3.6.1.4.1.28097.8.2.1.1.12 | ColumnconfigPhyWifiClusterMode | read-write | current | Cluster mode, empty for none, 'dualscan' for data/scan separation |
| 1.3.6.1.4.1.28097.8.2.1.1.13 | ColumnconfigPhyWifiClusterList | read-write | current | List of device names in the cluster, e.g. 'radio0 radio1' |
| 1.3.6.1.4.1.28097.8.2.1.1.14 | ColumnconfigPhyWifiClusterArgs | read-write | current | Cluster params for this device. For 'dualscan' mode, one device must be set to 'scan', the others in the cluster must be set to 'data'. |
| 1.3.6.1.4.1.28097.8.2.1.1.15 | ColumnconfigPhyWifiAntennaPorts | read-write | current | Antenna port configuration. |
| 1.3.6.1.4.1.28097.8.2.1.1.16 | ColumnconfigPhyWifiABGBasicRates | read-write | current | Space separated list of basic rates (in kbps). A value of 0 indicates that your radio device is configured on automatic basic rate. |
| 1.3.6.1.4.1.28097.8.2.1.1.17 | ColumnconfigPhyWifiABGSupportedRates | read-write | current | Space separated list of supported rates (in kbps). A value of 0 indicates that your radio device is configured on automatic supported rate. |
| 1.3.6.1.4.1.28097.8.2.1.1.18 | ColumnconfigPhyWifiChannelList | read-write | current | Configured radio channel list: Display/enter one or several channels, separated by spaces. 'auto' or '0' indicates automatic channel select. Ignored in client … |
| 1.3.6.1.4.1.28097.8.2.1.1.19 | ColumnconfigPhyWifiWids | read-write | current | WIDS functions selection. 0: radio is not reserved for WIDS (default). 1: radio is reserved for rogue AP monitoring. [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.8.2.2 | TableconfigPhyCellTable | not-accessible | current | List of Cellular radio devices [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.8.2.2.1 | RowconfigPhyCellEntry | not-accessible | current | Details about a cellular radio device |
| 1.3.6.1.4.1.28097.8.2.2.1.1 | ColumnconfigPhyCellName | read-only | current | Symbolic identifier for the radio device |
| 1.3.6.1.4.1.28097.8.2.2.1.2 | ColumnconfigPhyCellLabel | read-only | current | The label physically identifying the plugs/indicators on the device box [PF:wwan:0] |
| 1.3.6.1.4.1.28097.8.2.2.1.3 | ColumnconfigPhyCellDisableAtBoot | read-write | current | Set the card to be forcibly disabled at boot time. If set to Enable, the associated network will be initially disabled after reboots. If set to Disable, the as… |
| 1.3.6.1.4.1.28097.8.2.2.1.4 | ColumnconfigPhyCellLogAT | read-write | current | Enable logging of internal AT commands/responses |
| 1.3.6.1.4.1.28097.8.2.2.1.5 | ColumnconfigPhyCellSIM | read-write | current | Default SIM/UICC activated at startup (for Dual SIM Single Standby radios) |
| 1.3.6.1.4.1.28097.8.2.2.1.6 | ColumnconfigPhyCellSetPIN | read-write | current | Not implemented. New PIN code value to set in the *currently selected* SIM card. Reading this OID returns nothing. WARNING 1: the corresponding configPhyCellSi… |
| 1.3.6.1.4.1.28097.8.2.2.1.7 | ColumnconfigPhyCellSetPUK | read-write | current | Not implemented. PUK code required to reset the PIN code of the *currently selected* SIM card to the value of configPhyCellSetPIN. Use this only if the SIM is … |
| 1.3.6.1.4.1.28097.8.2.2.1.8 | ColumnconfigPhyCellSetPINStatus | read-only | current | Not implemented. Status of a write operation to configPhyCellSetPIN / configPhyCellSetPUK. set-init: no operation was requested yet set-more: more data (PUK co… |
| 1.3.6.1.4.1.28097.8.2.2.1.9 | ColumnconfigPhyCellSim1Pin | read-write | current | PIN code required to enable the SIM card |
| 1.3.6.1.4.1.28097.8.2.2.1.10 | ColumnconfigPhyCellSim1Apn | read-write | current | APN - Name of the cellular sub-service for IP. If left empty, the default subscriber's APN will be used |
| 1.3.6.1.4.1.28097.8.2.2.1.11 | ColumnconfigPhyCellSim1Authentication | read-write | current | Authentication type towards the Telecom network |
| 1.3.6.1.4.1.28097.8.2.2.1.12 | ColumnconfigPhyCellSim1Identity | read-write | current | User name for PAP/CHAP authentication |
| 1.3.6.1.4.1.28097.8.2.2.1.13 | ColumnconfigPhyCellSim1Password | read-write | current | User password for PAP/CHAP authentication |
| 1.3.6.1.4.1.28097.8.2.2.1.14 | ColumnconfigPhyCellSim2Pin | read-write | current | PIN code required to enable the SIM card |
| 1.3.6.1.4.1.28097.8.2.2.1.15 | ColumnconfigPhyCellSim2Apn | read-write | current | APN - Name of the cellular sub-service for IP. If left empty, the default subscriber's APN will be used |
| 1.3.6.1.4.1.28097.8.2.2.1.16 | ColumnconfigPhyCellSim2Authentication | read-write | current | Authentication type towards the Telecom network |
| 1.3.6.1.4.1.28097.8.2.2.1.17 | ColumnconfigPhyCellSim2Identity | read-write | current | User name for PAP/CHAP authentication |
| 1.3.6.1.4.1.28097.8.2.2.1.18 | ColumnconfigPhyCellSim2Password | read-write | current | User password for PAP/CHAP authentication |
| 1.3.6.1.4.1.28097.8.3 | Nodenetif | |||
| 1.3.6.1.4.1.28097.8.3.1 | Nodenetdetails | |||
| 1.3.6.1.4.1.28097.8.3.1.1 | TableconfigRadiusTable | not-accessible | current | List of radius servers currently defined [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.1.1.1 | RowconfigRadiusEntry | not-accessible | current | Details about a radius server [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.1.1.1.1 | ColumnconfigRadiusIndex | read-only | current | Radius index, maximum 4 items support |
| 1.3.6.1.4.1.28097.8.3.1.1.1.2 | ColumnconfigRadiusRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.8.3.1.1.1.3 | ColumnconfigRadiusIpAddress | read-write | current | Radius IPv4 address |
| 1.3.6.1.4.1.28097.8.3.1.1.1.4 | ColumnconfigRadiusPort | read-write | current | Radius UDP port |
| 1.3.6.1.4.1.28097.8.3.1.1.1.5 | ColumnconfigRadiusSecret | read-write | current | Radius shared secret |
| 1.3.6.1.4.1.28097.8.3.1.2 | ScalarconfigDetailsNasId | read-write | current | NAS identifier for the RADIUS servers [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.1.3 | TableconfigFilterGroupTable | not-accessible | current | List of filter group. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.1.3.1 | RowconfigFilterGroupEntry | not-accessible | current | Details about a filter group [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.1.3.1.1 | ColumnconfigFilterGroupIndex | read-write | current | filter group index |
| 1.3.6.1.4.1.28097.8.3.1.3.1.2 | ColumnconfigFilterGroupRowStatus | read-create | current | row addition/deletion support [PF:fgroup_:1] |
| 1.3.6.1.4.1.28097.8.3.1.3.1.3 | ColumnconfigFilterGroupFriendlyName | read-write | current | Filter group friendly name (as displayed in the web UI) |
| 1.3.6.1.4.1.28097.8.3.1.4 | TableconfigFilterGroupRuleTable | not-accessible | current | List of filter group rules. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.1.4.1 | RowconfigFilterGroupRuleEntry | not-accessible | current | Details about a filter rule [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.1.4.1.1 | ColumnconfigFilterGroupRuleIndex | read-write | current | filter group rule index |
| 1.3.6.1.4.1.28097.8.3.1.4.1.2 | ColumnconfigFilterGroupRuleRowStatus | read-create | current | row addition/deletion support [PF:frule_:1] |
| 1.3.6.1.4.1.28097.8.3.1.4.1.3 | ColumnconfigFilterGroupGroupIndex | read-write | current | Filter group to which the rule belongs to |
| 1.3.6.1.4.1.28097.8.3.1.4.1.4 | ColumnconfigFilterGroupRuleMACFrameType | read-write | current | Type of frame |
| 1.3.6.1.4.1.28097.8.3.1.4.1.5 | ColumnconfigFilterGroupRuleCheckMAC | read-write | current | frame MAC field to check |
| 1.3.6.1.4.1.28097.8.3.1.4.1.6 | ColumnconfigFilterGroupRuleNetworkProtocol | read-write | current | Network protocol. nofilter(-1), IP(-2), ARP(-3), (>0) for custom protocol. IP and ARP are shortcuts for 2048 (0x800) and 2054 (0x806) -255: invalid value |
| 1.3.6.1.4.1.28097.8.3.1.4.1.7 | ColumnconfigFilterGroupRuleIpAddress | read-write | current | Group rule filter IP address. |
| 1.3.6.1.4.1.28097.8.3.1.4.1.8 | ColumnconfigFilterGroupRuleNetmask | read-write | current | Group rule filter netmask. |
| 1.3.6.1.4.1.28097.8.3.1.4.1.9 | ColumnconfigFilterGroupRuleCheckIP | read-write | current | IP frame field to check |
| 1.3.6.1.4.1.28097.8.3.1.4.1.10 | ColumnconfigFilterGroupRuleTransportProtocol | read-write | current | Type of transport protocol |
| 1.3.6.1.4.1.28097.8.3.1.4.1.11 | ColumnconfigFilterGroupRuleFirstPort | read-write | current | Lower bound of port selection -255: invalid value |
| 1.3.6.1.4.1.28097.8.3.1.4.1.12 | ColumnconfigFilterGroupRuleLastPort | read-write | current | Upper bound of port selection -255: invalid value |
| 1.3.6.1.4.1.28097.8.3.1.4.1.13 | ColumnconfigFilterGroupRuleCheckPort | read-write | current | Transport field to check |
| 1.3.6.1.4.1.28097.8.3.2 | TableconfigInterfaceTable | not-accessible | current | List of network interfaces currently defined. The interfaces are defined by firmware. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.2.1 | RowconfigInterfaceEntry | not-accessible | current | Details about a network interface [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.2.1.1 | ColumnconfigInterfaceName | read-only | current | Symbolic name of the interface. Referenced in masters and slave interfaces. |
| 1.3.6.1.4.1.28097.8.3.2.1.2 | ColumnconfigInterfaceRowStatus | read-create | current | row addition/deletion support [MAX-ACCESS:read-only] |
| 1.3.6.1.4.1.28097.8.3.2.1.3 | ColumnconfigInterfaceType | read-only | current | Interface type: eth, AP, wifi client... |
| 1.3.6.1.4.1.28097.8.3.2.1.4 | ColumnconfigInterfaceDepends | read-write | current | The master interface this interface belongs to. Only the bridge type interface can be displayed and configured here. For the ipSubnet type interface which this… |
| 1.3.6.1.4.1.28097.8.3.2.1.5 | ColumnconfigInterfaceOutputFilterGroup | read-write | current | The output filter group this interface belongs to. Please refer to configFilterGroupTable and configFilterGroupRuleTable in order to check or change filter gro… |
| 1.3.6.1.4.1.28097.8.3.2.1.6 | ColumnconfigInterfaceFilterGroupDir | read-write | obsolete | The filter group traffic direction. Attention: This OID is obsolete. |
| 1.3.6.1.4.1.28097.8.3.2.1.7 | ColumnconfigInterfaceInputFilterGroup | read-write | current | The input filter group this interface belongs to. Please refer to configFilterGroupTable and configFilterGroupRuleTable in order to check or change filter grou… |
| 1.3.6.1.4.1.28097.8.3.3 | TableconfigIfStaTable | not-accessible | current | List of Wi-Fi client connections currently defined [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.3.1 | RowconfigIfStaEntry | not-accessible | current | Details about a Wi-Fi service set [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.3.1.1 | ColumnconfigIfStaName | read-only | current | Symbolic name of the wlan. Referred to in the general Interfaces table. |
| 1.3.6.1.4.1.28097.8.3.3.1.2 | ColumnconfigIfStaRowStatus | read-create | current | row addition/deletion support [radio] |
| 1.3.6.1.4.1.28097.8.3.3.1.3 | ColumnconfigIfStaPhy | read-only | current | PHY index for this wlan |
| 1.3.6.1.4.1.28097.8.3.3.1.4 | ColumnconfigIfStaSsid | read-write | current | SSID string |
| 1.3.6.1.4.1.28097.8.3.3.1.5 | ColumnconfigIfStaBssid | read-write | current | Not implemented yet [MAX-ACCESS:read-only] |
| 1.3.6.1.4.1.28097.8.3.3.1.6 | ColumnconfigIfStaBridgingMode | read-write | current | Bridging mode. |
| 1.3.6.1.4.1.28097.8.3.3.1.7 | ColumnconfigIfStaScanChannels | read-write | current | List of radio frequencies (in MHz) scanned for the next AP discovery: Ignored if roaming is disabled. |
| 1.3.6.1.4.1.28097.8.3.3.1.8 | ColumnconfigIfStaScanPassive | read-write | current | Not implemented yet [MAX-ACCESS:read-only] |
| 1.3.6.1.4.1.28097.8.3.3.1.9 | ColumnconfigIfStaRoamingEnable | read-write | current | Global fast-handover/roaming function activation |
| 1.3.6.1.4.1.28097.8.3.3.1.10 | ColumnconfigIfStaRoamingEnableDBM | read-write | current | Roaming is allowed when current AP signal drops below this level (negative value, e.g. -60) |
| 1.3.6.1.4.1.28097.8.3.3.1.11 | ColumnconfigIfStaRoamingRequiredBoost | read-write | current | Roaming occurs only if the candidate signal level is above the current AP's plus this value |
| 1.3.6.1.4.1.28097.8.3.3.1.12 | ColumnconfigIfStaRoamingScanPeriod | read-write | current | Background scan period when roaming is enabled |
| 1.3.6.1.4.1.28097.8.3.3.1.13 | ColumnconfigIfStaSecurityMode | read-write | current | Security policy |
| 1.3.6.1.4.1.28097.8.3.3.1.14 | ColumnconfigIfStaWepKey1 | read-write | current | WEP key 1 in hexadecimal format |
| 1.3.6.1.4.1.28097.8.3.3.1.15 | ColumnconfigIfStaWepKey2 | read-write | current | WEP key 2 in hexadecimal format |
| 1.3.6.1.4.1.28097.8.3.3.1.16 | ColumnconfigIfStaWepKey3 | read-write | current | WEP key 3 in hexadecimal format |
| 1.3.6.1.4.1.28097.8.3.3.1.17 | ColumnconfigIfStaWepKey4 | read-write | current | WEP key 4 in hexadecimal format |
| 1.3.6.1.4.1.28097.8.3.3.1.18 | ColumnconfigIfStaWepKey | read-write | current | WEP key slot selected: a value between 1 and 4 that indicates select one of the four WEP keys Ignored if configIfStaSecurityMode is different than wep. |
| 1.3.6.1.4.1.28097.8.3.3.1.19 | ColumnconfigIfStaWpaVersion | read-write | current | WPA version. Ignored if configIfStaSecurityMode is different than wpa-*. |
| 1.3.6.1.4.1.28097.8.3.3.1.20 | ColumnconfigIfStaWpaCipher | read-only | current | WPA cipher: WPA mode supports only TKIP(1). WPA2 mode supports only AES(2). Mixed WPA/WPA2 mode supports only AESTKIP(3). WPA3 mode supports only AES(2). Mixed… |
| 1.3.6.1.4.1.28097.8.3.3.1.21 | ColumnconfigIfStaIdentity | read-write | current | User ID (PEAP, TTLS) |
| 1.3.6.1.4.1.28097.8.3.3.1.22 | ColumnconfigIfStaKey | read-write | current | User password or WPA-PSK passphrase (or WPA 64-hex key) or TLS private key password |
| 1.3.6.1.4.1.28097.8.3.3.1.23 | ColumnconfigIfStaPrivateKey | read-write | current | TLS private key. A GET for this OID returns a string whose first byte is '1' if the key was uploaded, else '0' |
| 1.3.6.1.4.1.28097.8.3.3.1.24 | ColumnconfigIfStaCACert | read-write | current | EAP certificate. A GET for this OID returns a string whose first byte is '1' if the key was uploaded, else '0' |
| 1.3.6.1.4.1.28097.8.3.3.1.25 | ColumnconfigIfStaEapType | read-write | current | EAP type; eap-peap is the same as eap-ttls |
| 1.3.6.1.4.1.28097.8.3.3.1.26 | ColumnconfigIfStaAuthentication | read-write | current | Authentication type for phase 2 |
| 1.3.6.1.4.1.28097.8.3.3.1.27 | ColumnconfigIfStaFastBSSTransitionActivated | read-write | current | 802.11r support (dot11FastBSSTransitionActivated): 802.11r supports only client mode with all WPA/WPA2 policies. |
| 1.3.6.1.4.1.28097.8.3.3.1.28 | ColumnconfigIfStaIgnorePreviousScansResults | read-write | current | When scanning for APs, ignore those APs found prior to the last scan pass |
| 1.3.6.1.4.1.28097.8.3.3.1.29 | ColumnconfigIfStaRoamingRssiSmoothingFactor | read-write | current | RSSI smoothing factor The RSSI of the current AP is computed over the last few beacons received. Select the importance of the last beacon relative to older one… |
| 1.3.6.1.4.1.28097.8.3.3.1.30 | ColumnconfigIfStaRoamingBeaconTimeout | read-write | current | Beacon timeout: Value in beacon interval unit. |
| 1.3.6.1.4.1.28097.8.3.3.1.31 | ColumnconfigIfStaWpaKeyCacheLifetime | read-write | current | Expressed in seconds. |
| 1.3.6.1.4.1.28097.8.3.3.1.32 | ColumnconfigIfStaRoamingCurrentApScanThreshold | read-write | current | In dBm, e.g. '-75'. Above (better than) this value, the device will stop scanning. Set to 0 to scan unconditionally. Incompatible with the Maximum signal level… |
| 1.3.6.1.4.1.28097.8.3.3.1.33 | ColumnconfigIfStaRoamingMinimumStaLevel | read-write | current | In dBm, e.g. '-75'. 0 to disable. Roaming won't occur if the candidate signal is below this level. Association is still possible if no other AP is available. |
| 1.3.6.1.4.1.28097.8.3.3.1.34 | ColumnconfigIfStaRoamingAboveLevelThreshold | read-write | current | In dBm, e.g. '-30'. Leave empty or 0 to disable. Roaming will occur when the current AP signal crosses and exceeds this value, and there is an acceptable candi… |
| 1.3.6.1.4.1.28097.8.3.3.1.35 | ColumnconfigIfStaRoamingMaxSignalLevel | read-write | current | In dBm, e.g. '-30'. Leave empty or 0 to disable. Must be greater or equal to the 'Excessive signal detection threshold'. Roaming will occur whenever the curren… |
| 1.3.6.1.4.1.28097.8.3.3.1.36 | ColumnconfigIfStaRoamingMinRoamDelay | read-write | current | In ms. Leave empty or 0 to disable. Roaming won't occur before this delay has elapsed since the last association. |
| 1.3.6.1.4.1.28097.8.3.3.1.37 | ColumnconfigIfStaRoamingNoReturnDelay | read-write | current | In ms. Leave empty or 0 to disable, max 180000 (3 mn). Roaming won't occur to an AP that was left recently (before this delay gos elapsed). The delay is cleare… |
| 1.3.6.1.4.1.28097.8.3.3.1.38 | ColumnconfigIfStaRoamingThresholdHysteresis | read-write | current | Value in dBm, e.g. '2'. Hysteresis used for all thresholds. This value will be added and substracted to each threshold to set the corresponding threshold hyste… |
| 1.3.6.1.4.1.28097.8.3.3.1.39 | ColumnconfigIfStaRoamingOffChanMaxDelay | read-write | current | In ms. Maximum delay offchannel (during which data must be buffered by the associated AP). Channels will be scanned without returning to the base channel, unti… |
| 1.3.6.1.4.1.28097.8.3.3.1.40 | ColumnconfigIfStaRoamingOffChanProbeDelay | read-write | current | In ms. Delay for collision avoidance after a channel switch, before sending the probe request. |
| 1.3.6.1.4.1.28097.8.3.3.1.41 | ColumnconfigIfStaRoamingPerChanProbeDelay | read-write | current | In ms. Time to wait for an answer from the access points. |
| 1.3.6.1.4.1.28097.8.3.3.1.42 | ColumnconfigIfStaUserCert | read-write | current | EAP User certificate. A GET for this OID returns a string whose first byte is '1' if the key was uploaded, else '0' |
| 1.3.6.1.4.1.28097.8.3.3.1.43 | ColumnconfigIfStaDeauthBeforeRoamingtoNextAP | read-write | current | Deauthenticate before roaming to next AP. Write 2 (Enable), the previous AP stops transmission immediately, saving up bandwidth. Write 1 (Disable), let more ti… |
| 1.3.6.1.4.1.28097.8.3.4 | TableconfigIfAPTable | not-accessible | current | Access point services table [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.4.1 | RowconfigIfAPEntry | not-accessible | current | Access point services details [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.4.1.1 | ColumnconfigIfAPName | read-only | current | Symbolic name of the wlan. Referred to in the general Interfaces table. |
| 1.3.6.1.4.1.28097.8.3.4.1.2 | ColumnconfigIfAPRowStatus | read-create | current | row addition/deletion support [radio] |
| 1.3.6.1.4.1.28097.8.3.4.1.3 | ColumnconfigIfAPPhy | read-only | current | PHY index for this wlan |
| 1.3.6.1.4.1.28097.8.3.4.1.4 | ColumnconfigIfAPSsid | read-write | current | SSID string |
| 1.3.6.1.4.1.28097.8.3.4.1.5 | ColumnconfigIfAPHidden | read-write | current | Do not broadcast SSID |
| 1.3.6.1.4.1.28097.8.3.4.1.6 | ColumnconfigIfAPWds | read-write | current | Enable WDS (4-addresses) stations support |
| 1.3.6.1.4.1.28097.8.3.4.1.7 | ColumnconfigIfAPIsolate | read-write | current | Isolate clients from eachother |
| 1.3.6.1.4.1.28097.8.3.4.1.8 | ColumnconfigIfAPSecurityMode | read-write | current | Security policy |
| 1.3.6.1.4.1.28097.8.3.4.1.9 | ColumnconfigIfAPWepKey1 | read-write | current | WEP key 1 in hexadecimal format |
| 1.3.6.1.4.1.28097.8.3.4.1.10 | ColumnconfigIfAPWepKey2 | read-write | current | WEP key 2 in hexadecimal format |
| 1.3.6.1.4.1.28097.8.3.4.1.11 | ColumnconfigIfAPWepKey3 | read-write | current | WEP key 3 in hexadecimal format |
| 1.3.6.1.4.1.28097.8.3.4.1.12 | ColumnconfigIfAPWepKey4 | read-write | current | WEP key 4 in hexadecimal format |
| 1.3.6.1.4.1.28097.8.3.4.1.13 | ColumnconfigIfAPWepKey | read-write | current | WEP key slot selected: a value between 1 and 4 that indicates select one of the four WEP keys. Ignored if configIfAPSecurityMode is different than wep. |
| 1.3.6.1.4.1.28097.8.3.4.1.14 | ColumnconfigIfAPWepAuthentication | read-write | current | Set WEP Authentication |
| 1.3.6.1.4.1.28097.8.3.4.1.15 | ColumnconfigIfAPWpaVersion | read-write | current | WPA version. Ignored if configIfAPSecurityMode is different than wpa-*. |
| 1.3.6.1.4.1.28097.8.3.4.1.16 | ColumnconfigIfAPWpaCipher | read-only | current | WPA cipher: WPA mode supports only TKIP(1). WPA2 mode supports only AES(2). WPA3 mode supports only AES(2). Mixed WPA/WPA2 mode supports only AESTKIP(3). Mixed… |
| 1.3.6.1.4.1.28097.8.3.4.1.17 | ColumnconfigIfAPKey | read-write | current | WPA key: In wpa-wpa2-psk security mode, this key is pre-shared key; In wpa-wpa3-psk security mode, this key is pre-shared key; In wpa-wpa2 (eap) security mode,… |
| 1.3.6.1.4.1.28097.8.3.4.1.18 | ColumnconfigIfAPRadiusIndex | read-write | current | RADIUS table entry index |
| 1.3.6.1.4.1.28097.8.3.4.1.19 | ColumnconfigIfAPPreAuthentication | read-write | current | Enable / Disable pre-authentication |
| 1.3.6.1.4.1.28097.8.3.4.1.20 | ColumnconfigIfAPMACFilterBehaviour | read-write | current | MAC address filter mode |
| 1.3.6.1.4.1.28097.8.3.4.1.21 | ColumnconfigIfAPMACFilterAddresses | read-write | current | MAC filter addresses separated by comas |
| 1.3.6.1.4.1.28097.8.3.4.1.22 | ColumnconfigIfAPWpaGroupRekey | read-write | current | Time interval for rekeying the WPA GTK in second |
| 1.3.6.1.4.1.28097.8.3.4.1.23 | ColumnconfigIfAPWpaPairRekey | read-write | current | Time interval for rekeying the WPA PTK in second |
| 1.3.6.1.4.1.28097.8.3.4.1.24 | ColumnconfigIfAPWpaMasterRekey | read-write | current | Time interval for rekeying the WPA GMK in second |
| 1.3.6.1.4.1.28097.8.3.4.1.25 | ColumnconfigIfAPWpaProtectedFrame | read-write | current | Protected management frame: Set for preventing a hacker DoS attack. Ignored if configIfApSecurityMode is different than wpa-*. By default, the management frame… |
| 1.3.6.1.4.1.28097.8.3.4.1.26 | ColumnconfigIfAPMaxSimultaneousAssoc | read-write | current | The maximum number of clients allowed to connect on the AP. -1 indicates invalid value. [FW:E2148.AC.1:3.12.9.1] |
| 1.3.6.1.4.1.28097.8.3.4.1.27 | ColumnconfigIfAPPasspointConfigName | read-write | current | Applied Passpoint config name. Empty name means Passpoint not activated. [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.8.3.5 | TableconfigIfMeshTable | not-accessible | current | List of 802.11s mesh interfaces currently defined [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.5.1 | RowconfigIfMeshEntry | not-accessible | current | Details about a 802.11s network [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.5.1.1 | ColumnconfigIfMeshName | read-only | current | Symbolic name of the wlan. Referred to in the general Interfaces table. |
| 1.3.6.1.4.1.28097.8.3.5.1.2 | ColumnconfigIfMeshRowStatus | read-create | current | row addition/deletion support [radio] |
| 1.3.6.1.4.1.28097.8.3.5.1.3 | ColumnconfigIfMeshPhy | read-only | current | PHY index for this wlan |
| 1.3.6.1.4.1.28097.8.3.5.1.4 | ColumnconfigIfMeshId | read-write | current | Mesh ID string |
| 1.3.6.1.4.1.28097.8.3.5.1.5 | ColumnconfigIfMeshSecurityMode | read-write | current | Security policy |
| 1.3.6.1.4.1.28097.8.3.5.1.6 | ColumnconfigIfMeshPreSharedKey | read-write | current | SAE preshared key. Ignored if configIfMeshSecurityMode is different than sae. |
| 1.3.6.1.4.1.28097.8.3.5.1.7 | ColumnconfigIfMeshPathRefreshTime | read-write | current | Mesh paths refresh interval (in ms) |
| 1.3.6.1.4.1.28097.8.3.5.1.8 | ColumnconfigIfMeshMinDiscoveryTimeout | read-write | current | Mesh min discovery timeout (in ms) |
| 1.3.6.1.4.1.28097.8.3.5.1.9 | ColumnconfigIfMeshActivePathTimeout | read-write | current | Mesh active path timeout (in ms) |
| 1.3.6.1.4.1.28097.8.3.5.1.10 | ColumnconfigIfMeshNetworkDiameterTraversalTime | read-write | current | Duration of a there and back again trough the mesh network (in TUs). 1 TU = 1024us |
| 1.3.6.1.4.1.28097.8.3.5.1.11 | ColumnconfigIfMeshRootMode | read-write | current | Mesh root mode. |
| 1.3.6.1.4.1.28097.8.3.5.1.12 | ColumnconfigIfMeshGatesAnnouncement | read-write | current | Enable / disable gates announcements. In case mesh root mode is different than not_root |
| 1.3.6.1.4.1.28097.8.3.5.1.13 | ColumnconfigIfMeshActivePathToRootTimeout | read-write | current | Mesh active path to root timeout (in TUs) (1 TU = 1024us). In case mesh root mode is proactive_preq or proactive_preq_prep |
| 1.3.6.1.4.1.28097.8.3.5.1.14 | ColumnconfigIfMeshPreqRootInterval | read-write | current | Mesh preq root interval (in TUs) (1 TU = 1024us). In case mesh root mode is proactive_preq or proactive_preq_prep |
| 1.3.6.1.4.1.28097.8.3.5.1.15 | ColumnconfigIfMeshRannRootInterval | read-write | current | Mesh RANN root interval (in TUs) (1 TU = 1024us). In case mesh root mode is proactive_rann |
| 1.3.6.1.4.1.28097.8.3.6 | TableconfigIfBridgeTable | not-accessible | current | List of MAC bridges modules currently defined [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.6.1 | RowconfigIfBridgeEntry | not-accessible | current | Details about a MAC bridge [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.6.1.1 | ColumnconfigIfBridgeName | read-only | current | Symbolic name of the MAC bridge. Referred to in the general Interfaces table. |
| 1.3.6.1.4.1.28097.8.3.6.1.2 | ColumnconfigIfBridgeRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.8.3.6.1.3 | ColumnconfigIfBridgeStp | read-write | current | 1 disables RSTP, 2 sets to automatic RSTP/STP determination, 3 enforces legacy STP |
| 1.3.6.1.4.1.28097.8.3.6.1.4 | ColumnconfigIfBridgePriority | read-write | current | (R)STP bridge priority |
| 1.3.6.1.4.1.28097.8.3.6.1.5 | ColumnconfigIfBridgeHello | read-write | current | (R)STP hello interval |
| 1.3.6.1.4.1.28097.8.3.6.1.6 | ColumnconfigIfBridgeMaxAge | read-write | current | (R)STP max age |
| 1.3.6.1.4.1.28097.8.3.6.1.7 | ColumnconfigIfBridgeForwardDelay | read-write | current | (R)STP forward delay |
| 1.3.6.1.4.1.28097.8.3.6.1.8 | ColumnconfigIfBridgeLldpForward | read-write | current | Enables the LLDP frame forwarding. Required for profinet device cloning |
| 1.3.6.1.4.1.28097.8.3.7 | TableconfigIfVlanTable | not-accessible | current | List of MAC Vlan modules currently defined [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.7.1 | RowconfigIfVlanEntry | not-accessible | current | Details about a MAC Vlan [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.8.3.7.1.1 | ColumnconfigIfVlanIndex | read-write | current | Vlan name |
| 1.3.6.1.4.1.28097.8.3.7.1.2 | ColumnconfigIfVlanRowStatus | read-create | current | row addition/deletion support [PF:vlan:1] |
| 1.3.6.1.4.1.28097.8.3.7.1.3 | ColumnconfigIfVlanFriendlyName | read-write | current | VLAN friendly name |
| 1.3.6.1.4.1.28097.8.3.7.1.4 | ColumnconfigIfVlanHostIfName | read-write | current | MAC Host interface |
| 1.3.6.1.4.1.28097.8.3.7.1.5 | ColumnconfigIfVlanId | read-write | current | Vlan Id |
| 1.3.6.1.4.1.28097.8.3.8 | TableconfigIfSrccTable | not-accessible | current | List of SRCC connections currently defined. [FW:E2148.AC.1:3.12.9.1] |
| 1.3.6.1.4.1.28097.8.3.8.1 | RowconfigIfSrccEntry | not-accessible | current | List of SRCC connections currently defined. [FW:E2148.AC.1:3.12.9.1] |
| 1.3.6.1.4.1.28097.8.3.8.1.1 | ColumnconfigIfSrccName | read-only | current | Symbolic name of the wlan. Referred to in the general Interfaces table. |
| 1.3.6.1.4.1.28097.8.3.8.1.2 | ColumnconfigIfSrccRowStatus | read-create | current | Row addition/deletion support [radio] |
| 1.3.6.1.4.1.28097.8.3.8.1.3 | ColumnconfigIfSrccPhy | read-only | current | PHY index for this wlan. |
| 1.3.6.1.4.1.28097.8.3.8.1.4 | ColumnconfigIfSrccDiscoverApSsid | read-write | current | SRCC SSID string for discovering the other potential partners. |
| 1.3.6.1.4.1.28097.8.3.8.1.5 | ColumnconfigIfSrccProductType | read-write | current | The devices on the same coach edge must have the same type. -1 indicates invalid value. |
| 1.3.6.1.4.1.28097.8.3.8.1.6 | ColumnconfigIfSrccDiscSigThreshold | read-write | current | Link establishment threshold in dBm. By default, the value is -50. A potential partner is valid if its signal level stays over Link establishment threshold dur… |
| 1.3.6.1.4.1.28097.8.3.8.1.7 | ColumnconfigIfSrccDiscDuration | read-write | current | Link establishment duration in seconds. By default, the value is 60. A potential partner is considered valid if its signal level stays over Link establishment … |
| 1.3.6.1.4.1.28097.8.3.8.1.8 | ColumnconfigIfSrccBrokenThreshold | read-write | current | Broken link threshold in dBm. By default, the value is -70. The established link is considered broken if its signal drops below Broken link threshold during mo… |
| 1.3.6.1.4.1.28097.8.3.8.1.9 | ColumnconfigIfSrccBrokenDuration | read-write | current | Broken link duration in seconds. By default, the value is 660. The established link is considered broken if its signal drops below Broken link threshold during… |
| 1.3.6.1.4.1.28097.8.3.8.1.10 | ColumnconfigIfSrccWifiBand | read-write | current | The WiFi frequency range fo the final links. band-5g (1) for the 5GHz and band-24 (2) for the 2.4GHz. -1 indicates invalid value. |
| 1.3.6.1.4.1.28097.8.3.8.1.11 | ColumnconfigIfSrccFirstChannel | read-write | current | The wireless channel associated with the first SRCC final link. -1 indicates invalid value. |
| 1.3.6.1.4.1.28097.8.3.8.1.12 | ColumnconfigIfSrccSecondChannel | read-write | current | The wireless channel associated with the first SRCC final link. -1 indicates invalid value. |
| 1.3.6.1.4.1.28097.8.3.8.1.13 | ColumnconfigIfSrccDiscScanDuration | read-write | current | The global duration in seconds of the Ethernet topology discovery scan. By default, the value is 120. |
| 1.3.6.1.4.1.28097.8.3.8.1.14 | ColumnconfigIfSrccMixRedundancy | read-write | current | Redundancy method. 1: Wifi+Wifi 2: Wifi+Ethernet 3: Wifi alone (not redundant) [SYNFW:3:E2148.AC.1:4.10.0.1]. |
| 1.3.6.1.4.1.28097.8.3.8.1.15 | ColumnconfigIfSrccMixRedundancyBoost | read-write | current | Gain in percent added to the target metric. Minimum = 1; maximum = 65535. By default, the value is 40. |
| 1.3.6.1.4.1.28097.8.3.8.1.16 | ColumnconfigIfSrccPeerTableTimeout | read-write | current | Peer table timeout in seconds: the wireless discover timeout for a partner(peer). By default, the value is 20. |
| 1.3.6.1.4.1.28097.8.3.8.1.17 | ColumnconfigIfSrccTargetTableTimeout | read-write | current | Target table timeout in seconds: the wireless discover timeout for the whole cell(the group of wireless peers). By default, the value is 120. |
| 1.3.6.1.4.1.28097.8.3.8.1.18 | ColumnconfigIfSrccPeerAcknowTimeout | read-write | current | The duration in seconds the Master waits for the answer from all partners after sending its proposed cell architecture. By default, the value is 120. |
| 1.3.6.1.4.1.28097.8.3.8.1.19 | ColumnconfigIfSrccPeerReconfigTimeout | read-write | current | The duration in seconds the Master waits for all the partners to switch to their final roles. By default, the value is 200. |
| 1.3.6.1.4.1.28097.8.3.8.1.20 | ColumnconfigIfSrccGreBridgeIpAddr | read-write | current | Internal L2 GRE interface IP prefix represents the GRE interface IP prefix. SRCC's internal uses a GRE L2 tunnel, in which the interface is configured with a C… |
| 1.3.6.1.4.1.28097.8.4 | Noderoaming | |||
| 1.3.6.1.4.1.28097.8.4.1 | ScalarroamingAlgorithm | read-write | current | Dual interface handover method. None: the same radio interface scans and transfers data. Scan: one designated radio scans only, and the other transfers data. C… |
| 1.3.6.1.4.1.28097.8.4.2 | ScalarroamingPLHposition | read-write | current | Position of the antenna relative to vehicle motion. Front: the vehicle antenna moves closer to the target APs. Rear: the vehicle antenna moves away from the ta… |
| 1.3.6.1.4.1.28097.8.4.3 | ScalarroamingPLHjitter | read-write | current | Minimum variation from highest sample to detect a slope direction change; e.g. 1 means detection needs at least 2 dB difference since the first 1dB is ignored.… |
| 1.3.6.1.4.1.28097.8.4.4 | ScalarroamingPLHurgent | read-write | current | When the current AP is below this level and there is no candidate AP, the candidate selection rules are relaxed and the statusRoamingUrgent OID changes state. … |
| 1.3.6.1.4.1.28097.8.4.5 | NoderoamingPLHfront | |||
| 1.3.6.1.4.1.28097.8.4.5.1 | ScalarroamingPLHfrontCandMin | read-write | current | Minimum signal level from an AP to select it as candidate target for a handover. [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.8.4.5.2 | ScalarroamingPLHfrontCandMax | read-write | current | Maximum signal level from an AP to select it as candidate target for a handover. An AP above this is supposedly about to be bypassed and might fade quickly. [F… |
| 1.3.6.1.4.1.28097.8.4.5.3 | ScalarroamingPLHfrontCurrentLow | read-write | current | Signal level from the AP dedicated to data transfer, below which a handover to a candidate will be attempted. [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.8.4.5.4 | ScalarroamingPLHfrontCurrentHigh | read-write | current | Signal level from the AP dedicated to data transfer, above which a handover to a candidate will be attempted. [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.8.4.6 | NoderoamingPLHrear | |||
| 1.3.6.1.4.1.28097.8.4.6.1 | ScalarroamingPLHrearCandMin | read-write | current | Minimum signal level from an AP to select it as candidate target for a handover. [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.8.4.6.2 | ScalarroamingPLHrearCandMax | read-write | current | Maximum signal level from an AP to select it as candidate target for a handover. An AP above this is supposedly about to be bypassed and might fade quickly. [F… |
| 1.3.6.1.4.1.28097.8.4.6.3 | ScalarroamingPLHrearCurrentLow | read-write | current | Signal level from the AP dedicated to data transfer, below which a handover to a candidate will be attempted. [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.8.4.6.4 | ScalarroamingPLHrearCurrentHigh | read-write | current | Signal level from the AP dedicated to data transfer, above which a handover to a candidate will be attempted. [FW:E2148.AC.1:4.12.0.1] |
| 1.3.6.1.4.1.28097.9 | NodeserviceStatus | |||
| 1.3.6.1.4.1.28097.9.1 | Nodess-webserver | |||
| 1.3.6.1.4.1.28097.9.2 | Nodess-dhcp | |||
| 1.3.6.1.4.1.28097.9.3 | Nodess-ntp | |||
| 1.3.6.1.4.1.28097.9.4 | Nodess-radius | |||
| 1.3.6.1.4.1.28097.9.5 | Nodess-snmp | |||
| 1.3.6.1.4.1.28097.9.5.1 | TablesnmpAgentOIDTable | not-accessible | current | List of SNMP agents variants for this entreprise [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.9.5.1.1 | RowsnmpAgentOIDEntry | not-accessible | current | Details about the SNMP agent implementation |
| 1.3.6.1.4.1.28097.9.5.1.1.1 | ColumnsnmpAgentOIDIndex | read-only | current | Agent variant ID |
| 1.3.6.1.4.1.28097.9.5.1.1.2 | ColumnsnmpAgentOIDProductID | read-only | current | Product ID code currently handled by this agent |
| 1.3.6.1.4.1.28097.9.6 | Nodess-dns | |||
| 1.3.6.1.4.1.28097.9.7 | Nodess-system | |||
| 1.3.6.1.4.1.28097.9.7.1 | ScalarsystemReady | read-only | current | This OID returns 2 when the product is fully initialized and ready to communicate. It returns 1 instead. Please refer to the wireless status in order to check … |
| 1.3.6.1.4.1.28097.9.7.2 | Nodesensors | |||
| 1.3.6.1.4.1.28097.9.7.2.1 | NodetempSensors | |||
| 1.3.6.1.4.1.28097.9.7.2.1.1 | ScalarmotherBoard0 | read-only | current | The temperature given by the motherboard sensor 0 in mC. A temperature equals or below -274000mC means that the sensor is not available. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.9.7.2.2 | TablegpioInTable | not-accessible | current | Digital input table [FW:E2148.AC.1:3.16.0.1] |
| 1.3.6.1.4.1.28097.9.7.2.2.1 | RowgpioInEntry | not-accessible | current | Digital input table [FW:E2148.AC.1:3.16.0.1] |
| 1.3.6.1.4.1.28097.9.7.2.2.1.1 | ColumngpioInIndex | read-only | current | gpio index |
| 1.3.6.1.4.1.28097.9.7.2.2.1.2 | ColumngpioInState | read-only | current | gpio index |
| 1.3.6.1.4.1.28097.9.7.2.3 | TablegpioOutTable | not-accessible | current | Digital output table [FW:E2148.AC.1:3.16.0.1] |
| 1.3.6.1.4.1.28097.9.7.2.3.1 | RowgpioOutEntry | not-accessible | current | Digital output table [FW:E2148.AC.1:3.16.0.1] |
| 1.3.6.1.4.1.28097.9.7.2.3.1.1 | ColumngpioOutIndex | read-only | current | gpio index |
| 1.3.6.1.4.1.28097.9.7.2.3.1.2 | ColumngpioOutState | read-write | current | gpio index |
| 1.3.6.1.4.1.28097.9.8 | Nodess-gnss | |||
| 1.3.6.1.4.1.28097.9.8.1 | Nodegnss-current-position | |||
| 1.3.6.1.4.1.28097.9.8.1.1 | ScalarpositionValid | read-only | current | Indicates if the GPS has managed to determine the position or not. [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.9.8.1.2 | Scalarfixdate | read-only | current | UTC date format YYYYMMDD [FW:E2148.AC.1:4.14.0.1] |
| 1.3.6.1.4.1.28097.9.8.1.3 | Scalarfixtime | read-only | current | UTC time format HHMMSS.mmm [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.9.8.1.4 | Scalarlatitude | read-only | current | Value in degrees [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.9.8.1.5 | Scalarlongitude | read-only | current | Value in degrees [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.9.8.1.6 | Scalaraltitude | read-only | current | Value in meters [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.9.8.1.7 | Scalarspeedkmh | read-only | current | speed in km/h [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.9.8.1.8 | ScalarcourseDegrees | read-only | current | Direction angle from North Valid only if speed not null. Return a type string [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.9.8.1.9 | Scalarfixdimension | read-only | current | Returns 2 for latitude/longitude only, 3 when altitude is available, 0 when fix is invalid. [FW:E2148.AC.1:3.14.0.1] |
| 1.3.6.1.4.1.28097.9.8.1.10 | ScalargnssAllPositions | read-only | current | Returns all GNSS fix data in a single column-separated string. The fields order is as follows: positionValid, fixDimension, fixDate, fixTime, latitude, longitu… |
| 1.3.6.1.4.1.28097.9.9 | Nodess-tcn | |||
| 1.3.6.1.4.1.28097.9.10 | Nodess-async-sysupgrade | |||
| 1.3.6.1.4.1.28097.9.10.1 | ScalarfirmwareExists | read-only | current | True if there is a valid firmware uploaded to the product. [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.9.10.2 | ScalarfirmwareInfo | read-only | current | Version of all parts in the uploaded firmware and check checksum of uploaded firmware. Pattern: [part1 name]:[part1 version];[part2 name]:[part2 version];...;[… |
| 1.3.6.1.4.1.28097.9.10.3 | ScalarsysupgradeMissed | read-only | current | True if there is a missed sysupgrade. [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.10 | NodeserviceConfiguration | |||
| 1.3.6.1.4.1.28097.10.1 | Nodesc-webserver | |||
| 1.3.6.1.4.1.28097.10.1.1 | ScalarconfigHttpServer | read-write | current | Enable / disable the internal Http server. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.10.1.2 | ScalarconfigHttpServerPort | read-write | current | Internal Http server TCP port. If the http server is disabled, this OID returns 0 [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.10.1.3 | ScalarconfigHttpsServer | read-write | current | Enable / disable the internal Https server. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.10.1.4 | ScalarconfigHttpsPort | read-write | current | Internal Https server TCP port. If the https server is disabled, this OID returns 0 [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.10.1.5 | ScalarconfigHttpsCertificate | read-write | current | Internal Https server certificate. A GET for this OID returns a string whose first byte is '1' if the key was uploaded, else '0' [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.10.2 | Nodesc-dhcp | |||
| 1.3.6.1.4.1.28097.10.2.1 | TableconfigDhcpTable | not-accessible | current | List of DHCP servers per subnet [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.10.2.1.1 | RowconfigDhcpEntry | not-accessible | current | Details about a configured DHCP server [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.10.2.1.1.1 | ColumnconfigDhcpSubnet | read-write | current | Interface on which this DHCP server instance is run |
| 1.3.6.1.4.1.28097.10.2.1.1.2 | ColumnconfigDhcpRowStatus | read-create | current | row addition/deletion support [net] [MAX-ACCESS:read-only] |
| 1.3.6.1.4.1.28097.10.2.1.1.3 | ColumnconfigDhcpEnable | read-write | current | Enable DHCP server instance |
| 1.3.6.1.4.1.28097.10.2.1.1.4 | ColumnconfigDhcpPoolStart | read-write | current | First IP address in the pool |
| 1.3.6.1.4.1.28097.10.2.1.1.5 | ColumnconfigDhcpPoolCount | read-write | current | Number of IP addresses in the pool |
| 1.3.6.1.4.1.28097.10.2.1.1.6 | ColumnconfigDhcpLeaseDuration | read-write | current | Lease time (seconds) |
| 1.3.6.1.4.1.28097.10.3 | Nodesc-ntp | |||
| 1.3.6.1.4.1.28097.10.3.1 | ScalarconfigNtp | not-accessible | current | Not implemented yet |
| 1.3.6.1.4.1.28097.10.4 | Nodesc-radius | |||
| 1.3.6.1.4.1.28097.10.5 | Nodesc-snmp | |||
| 1.3.6.1.4.1.28097.10.6 | Nodesc-dns | |||
| 1.3.6.1.4.1.28097.10.6.1 | NodeconfigRelay | |||
| 1.3.6.1.4.1.28097.10.6.1.1 | ScalarconfigDnsRebindProtection | read-write | current | Enable / disable DNS rebind attack protection. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.10.6.1.2 | ScalarconfigDnsRebindLocalhost | read-write | current | Allow / Disallow DNS response with IP address in 127.0.0.0/8 range. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.10.7 | Nodesc-ssh | |||
| 1.3.6.1.4.1.28097.10.7.1 | ScalarconfigSshEnable | read-write | current | Enable ssh [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.10.7.2 | ScalarconfigSshEnablePwd | read-write | current | Enable ssh user/password login [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.10.8 | Nodesc-tcn | |||
| 1.3.6.1.4.1.28097.10.9 | Nodesc-collectd | |||
| 1.3.6.1.4.1.28097.10.9.1 | ScalarconfigCollectdEnable | read-write | current | Collectd service enable [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.10.9.2 | ScalarconfigCollectdSamplingInterval | read-write | current | Collectd sampling interval in seconds [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.10.9.3 | Nodeplugin-GPS | |||
| 1.3.6.1.4.1.28097.10.9.3.1 | ScalarconfigCollectdGPSEnable | read-write | current | Collectd plugin GPS enable [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.10.9.3.2 | ScalarconfigCollectdGPSServerAddr | read-write | current | Collectd plugin GPS server's IP address [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.10.9.3.3 | ScalarconfigCollectdGPSServerPort | read-write | current | Collectd plugin GPS server's port [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.10.9.3.4 | ScalarconfigCollectdGPSConnTimeout | read-write | current | Collectd plugin GPS connection timeout in seconds [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.10.9.3.5 | ScalarconfigCollectdGPSReqInterval | read-write | current | Collectd plugin GPS request interval in seconds [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.10.9.4 | Nodeplugin-AcksysScanResult | |||
| 1.3.6.1.4.1.28097.10.9.4.1 | ScalarconfigCollectdWirelessScanResult | read-write | current | Enable wireless scan result collection [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.10.9.5 | Nodeplugin-iwinfo | |||
| 1.3.6.1.4.1.28097.10.9.5.1 | ScalarconfigCollectdIwinfo | read-write | current | Enable wireless info collection [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.10.9.6 | Nodeplugin-AcksysTelemetry | |||
| 1.3.6.1.4.1.28097.10.9.6.1 | ScalarconfigAcksysTelemetryEnable | read-write | current | Enable Acksys telemetry plugin [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.10.9.6.2 | ScalarconfigAcksysTelemetryServerPort | read-write | current | Acksys telemetry plugin server's port [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.10.9.6.3 | ScalarconfigAcksysTelemetryOutputInterval | read-write | current | Interval in seconds of Acksys telemetry data transmission [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.10.9.6.4 | ScalarconfigAcksysTelemetryMaxBufferSize | read-write | current | Size of buffer that acksys telemetry used internally [FW:E2148.AC.1:4.10.0.1] |
| 1.3.6.1.4.1.28097.10.10 | Nodesc-passpoint | |||
| 1.3.6.1.4.1.28097.10.10.1 | TableconfigPasspointConfigTable | not-accessible | current | List of Passpoint configurations [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.1.1 | RowconfigPasspointConfigEntry | not-accessible | current | Entry of Passpoint configuration [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.1.1.1 | ColumnconfigPasspointConfigName | read-write | current | configPasspointConfigName |
| 1.3.6.1.4.1.28097.10.10.1.1.2 | ColumnconfigPasspointConfigRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.1.1.3 | ColumnconfigPasspointConfigAnqpAccessNetworkType | read-write | current | configPasspointConfigAnqpAccessNetworkType |
| 1.3.6.1.4.1.28097.10.10.1.1.4 | ColumnconfigPasspointConfigAnqpInternet | read-write | current | configPasspointConfigAnqpInternet |
| 1.3.6.1.4.1.28097.10.10.1.1.5 | ColumnconfigPasspointConfigAnqpAsra | read-write | current | configPasspointConfigAnqpAsra |
| 1.3.6.1.4.1.28097.10.10.1.1.6 | ColumnconfigPasspointConfigAnqpEsr | read-write | current | configPasspointConfigAnqpEsr |
| 1.3.6.1.4.1.28097.10.10.1.1.7 | ColumnconfigPasspointConfigAnqpUesa | read-write | current | configPasspointConfigAnqpUesa |
| 1.3.6.1.4.1.28097.10.10.1.1.8 | ColumnconfigPasspointConfigAnqpHessid | read-write | current | configPasspointConfigAnqpHessid |
| 1.3.6.1.4.1.28097.10.10.1.1.9 | ColumnconfigPasspointConfigAnqpGasAddress3 | read-write | current | configPasspointConfigAnqpGasAddress3 |
| 1.3.6.1.4.1.28097.10.10.1.1.10 | ColumnconfigPasspointConfigAnqpVenueProfile | read-write | current | configPasspointConfigAnqpVenueProfile |
| 1.3.6.1.4.1.28097.10.10.1.1.11 | ColumnconfigPasspointConfigAnqpRoamingConsortiumProfile | read-write | current | configPasspointConfigAnqpRoamingConsortiumProfile |
| 1.3.6.1.4.1.28097.10.10.1.1.12 | ColumnconfigPasspointConfigAnqpNetworkAuthTypeProfile | read-write | current | configPasspointConfigAnqpNetworkAuthTypeProfile |
| 1.3.6.1.4.1.28097.10.10.1.1.13 | ColumnconfigPasspointConfigAnqpIpAddrTypeAvailProfile | read-write | current | configPasspointConfigAnqpIpAddrTypeAvailProfile |
| 1.3.6.1.4.1.28097.10.10.1.1.14 | ColumnconfigPasspointConfigAnqpDomainNameProfile | read-write | current | configPasspointConfigAnqpDomainNameProfile |
| 1.3.6.1.4.1.28097.10.10.1.1.15 | ColumnconfigPasspointConfigAnqp3gppCellNetProfile | read-write | current | configPasspointConfigAnqp3gppCellNetProfile |
| 1.3.6.1.4.1.28097.10.10.1.1.16 | ColumnconfigPasspointConfigAnqpNaiRealmProfile | read-write | current | configPasspointConfigAnqpNaiRealmProfile |
| 1.3.6.1.4.1.28097.10.10.1.1.17 | ColumnconfigPasspointConfigAnqpOverrideElementProfile | read-write | current | configPasspointConfigAnqpOverrideElementProfile |
| 1.3.6.1.4.1.28097.10.10.1.1.18 | ColumnconfigPasspointConfigHS20DisableDgaf | read-write | current | configPasspointConfigHS20DisableDgaf |
| 1.3.6.1.4.1.28097.10.10.1.1.19 | ColumnconfigPasspointConfigHS20DomainId | read-write | current | configPasspointConfigHS20DomainId |
| 1.3.6.1.4.1.28097.10.10.1.1.20 | ColumnconfigPasspointConfigHS20DeauthReqTimeout | read-write | current | configPasspointConfigHS20DeauthReqTimeout |
| 1.3.6.1.4.1.28097.10.10.1.1.21 | ColumnconfigPasspointConfigHS20OsuSsid | read-write | current | configPasspointConfigHS20OsuSsid |
| 1.3.6.1.4.1.28097.10.10.1.1.22 | ColumnconfigPasspointConfigHS20OperFriendlyNameProfile | read-write | current | configPasspointConfigHS20OperFriendlyNameProfile |
| 1.3.6.1.4.1.28097.10.10.1.1.23 | ColumnconfigPasspointConfigHS20ConnCapProfile | read-write | current | configPasspointConfigHS20ConnCapProfile |
| 1.3.6.1.4.1.28097.10.10.1.1.24 | ColumnconfigPasspointConfigHS20WanMetricsProfile | read-write | current | configPasspointConfigHS20WanMetricsProfile |
| 1.3.6.1.4.1.28097.10.10.1.1.25 | ColumnconfigPasspointConfigHS20OperClassProfile | read-write | current | configPasspointConfigHS20OperClassProfile |
| 1.3.6.1.4.1.28097.10.10.1.1.26 | ColumnconfigPasspointConfigHS20OsuProviderProfile | read-write | current | configPasspointConfigHS20OsuProviderProfile |
| 1.3.6.1.4.1.28097.10.10.2 | TableconfigAnqpProfileVenueTable | not-accessible | current | List of configAnqpProfileVenueTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.2.1 | RowconfigAnqpProfileVenueEntry | not-accessible | current | List of configAnqpProfileVenue [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.2.1.1 | ColumnconfigProfileVenueName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.2.1.2 | ColumnconfigProfileVenueRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.2.1.3 | ColumnconfigProfileVenueDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.2.1.4 | ColumnconfigVenueGroup | read-write | current | Venue groupe |
| 1.3.6.1.4.1.28097.10.10.2.1.5 | ColumnconfigVenueType | read-write | current | Venue groupe |
| 1.3.6.1.4.1.28097.10.10.2.1.6 | ColumnconfigVenueNameList | read-write | current | Venue name. Format: [country 1 code]:[name 1 string],[country 2 code]:[name 2 string]... |
| 1.3.6.1.4.1.28097.10.10.3 | TableconfigAnqpProfileRoamingConsortiumTable | not-accessible | current | List of configAnqpProfileRoamingConsortiumTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.3.1 | RowconfigAnqpProfileRoamingConsortiumEntry | not-accessible | current | List of configAnqpProfileRoamingConsortium [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.3.1.1 | ColumnconfigProfileRoamingConsortiumName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.3.1.2 | ColumnconfigProfileRoamingConsortiumRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.3.1.3 | ColumnconfigProfileRoamingConsortiumDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.3.1.4 | ColumnconfigRoamingConsortiumList | read-write | current | List of roaming consortium. |
| 1.3.6.1.4.1.28097.10.10.4 | TableconfigAnqpProfileNetworkAuthTypeTable | not-accessible | current | List of configAnqpProfileNetworkAuthTypeTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.4.1 | RowconfigAnqpProfileNetworkAuthTypeEntry | not-accessible | current | List of configAnqpProfileNetworkAuthType [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.4.1.1 | ColumnconfigProfileNetworkAuthTypeName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.4.1.2 | ColumnconfigProfileNetworkAuthTypeRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.4.1.3 | ColumnconfigProfileNetworkAuthTypeDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.4.1.4 | ColumnconfigNetworkAuthType | read-write | current | Network auth type |
| 1.3.6.1.4.1.28097.10.10.5 | TableconfigAnqpProfileIpAddrTypeAvailTable | not-accessible | current | List of configAnqpProfileIpAddrTypeAvailTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.5.1 | RowconfigAnqpProfileIpAddrTypeAvailEntry | not-accessible | current | List of configAnqpProfileIpAddrTypeAvail [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.5.1.1 | ColumnconfigProfileIpAddrTypeAvailName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.5.1.2 | ColumnconfigProfileIpAddrTypeAvailRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.5.1.3 | ColumnconfigProfileIpAddrTypeAvailDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.5.1.4 | ColumnconfigIpv4Type | read-write | current | IPv4 address availability. |
| 1.3.6.1.4.1.28097.10.10.5.1.5 | ColumnconfigIpv6Type | read-write | current | IPv6 address availability. |
| 1.3.6.1.4.1.28097.10.10.6 | TableconfigAnqpProfileDomainNameTable | not-accessible | current | List of configAnqpProfileDomainNameTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.6.1 | RowconfigAnqpProfileDomainNameEntry | not-accessible | current | List of configAnqpProfileDomainName [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.6.1.1 | ColumnconfigProfileDomainNameName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.6.1.2 | ColumnconfigProfileDomainNameRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.6.1.3 | ColumnconfigProfileDomainNameDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.6.1.4 | ColumnconfigDomainNameList | read-write | current | Domain name list. |
| 1.3.6.1.4.1.28097.10.10.7 | TableconfigAnqpProfile3gppCellNetTable | not-accessible | current | List of configAnqpProfile3gppCellNetTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.7.1 | RowconfigAnqpProfile3gppCellNetEntry | not-accessible | current | List of configAnqpProfile3gppCellNet [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.7.1.1 | ColumnconfigProfile3gppCellNetName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.7.1.2 | ColumnconfigProfile3gppCellNetRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.7.1.3 | ColumnconfigProfile3gppCellNetDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.7.1.4 | Columnconfig3gppCellNetList | read-write | current | 3GPP Cell Net list, MCC1:MNC1;MCC2:MNC2... |
| 1.3.6.1.4.1.28097.10.10.8 | TableconfigAnqpProfileNaiRealmTable | not-accessible | current | List of configAnqpProfileNaiRealmTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.8.1 | RowconfigAnqpProfileNaiRealmEntry | not-accessible | current | List of configAnqpProfileNaiRealm [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.8.1.1 | ColumnconfigProfileNaiRealmName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.8.1.2 | ColumnconfigProfileNaiRealmRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.8.1.3 | ColumnconfigProfileNaiRealmDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.8.1.4 | ColumnconfigNaiRealmEncode | read-write | current | NAI Realm Encode |
| 1.3.6.1.4.1.28097.10.10.8.1.5 | ColumnconfigNaiRealmRealmList | read-write | current | NAI Realm list |
| 1.3.6.1.4.1.28097.10.10.8.1.6 | ColumnconfigNaiRealmEap | read-write | current | NAI Real EAP |
| 1.3.6.1.4.1.28097.10.10.9 | TableconfigAnqpProfileOverrideElementTable | not-accessible | current | List of configAnqpProfileOverrideElementTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.9.1 | RowconfigAnqpProfileOverrideElementEntry | not-accessible | current | List of configAnqpProfileOverrideElement [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.9.1.1 | ColumnconfigProfileOverrideElementName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.9.1.2 | ColumnconfigProfileOverrideElementRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.9.1.3 | ColumnconfigProfileOverrideElementDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.9.1.4 | ColumnconfigAnqpOverrideList | read-write | current | ANQP override element list. |
| 1.3.6.1.4.1.28097.10.10.10 | TableconfigHS20ProfileOperFriendlyNameTable | not-accessible | current | List of configHS20ProfileOperFriendlyNameTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.10.1 | RowconfigHS20ProfileOperFriendlyNameEntry | not-accessible | current | List of configHS20ProfileOperFriendlyName [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.10.1.1 | ColumnconfigProfileOperFriendlyNameName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.10.1.2 | ColumnconfigProfileOperFriendlyNameRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.10.1.3 | ColumnconfigProfileOperFriendlyNameDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.10.1.4 | ColumnconfigFriendlyNameList | read-write | current | List of friendly name. Format: [language 1 code]:[name 1 string];[language 2 code]:[name 2 string] |
| 1.3.6.1.4.1.28097.10.10.11 | TableconfigHS20ProfileConnCapTable | not-accessible | current | List of configHS20ProfileConnCapTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.11.1 | RowconfigHS20ProfileConnCapEntry | not-accessible | current | List of configHS20ProfileConnCap [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.11.1.1 | ColumnconfigProfileConnCapName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.11.1.2 | ColumnconfigProfileConnCapRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.11.1.3 | ColumnconfigProfileConnCapDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.11.1.4 | ColumnconfigConnCapabList | read-write | current | Connection capability list. |
| 1.3.6.1.4.1.28097.10.10.12 | TableconfigHS20ProfileWanMetricsTable | not-accessible | current | List of configHS20ProfileWanMetricsTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.12.1 | RowconfigHS20ProfileWanMetricsEntry | not-accessible | current | List of configHS20ProfileWanMetrics [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.12.1.1 | ColumnconfigProfileWanMetricsName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.12.1.2 | ColumnconfigProfileWanMetricsRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.12.1.3 | ColumnconfigProfileWanMetricsDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.12.1.4 | ColumnconfigLinkStatus | read-write | current | Link status. |
| 1.3.6.1.4.1.28097.10.10.12.1.5 | ColumnconfigSymmetric | read-write | current | Link symmetric. |
| 1.3.6.1.4.1.28097.10.10.12.1.6 | ColumnconfigAtCapacity | read-write | current | Link at capacity. |
| 1.3.6.1.4.1.28097.10.10.12.1.7 | ColumnconfigDownSpeed | read-write | current | Down link speed in kbps. |
| 1.3.6.1.4.1.28097.10.10.12.1.8 | ColumnconfigUpSpeed | read-write | current | Up link speed in kbps. |
| 1.3.6.1.4.1.28097.10.10.12.1.9 | ColumnconfigDownLoad | read-write | current | Current load of downlink WAN connection in percentage. |
| 1.3.6.1.4.1.28097.10.10.12.1.10 | ColumnconfigUpLoad | read-write | current | Current load of uplink WAN connection in percentage. |
| 1.3.6.1.4.1.28097.10.10.12.1.11 | ColumnconfigLMD | read-write | current | Duration for measuring downlink/uplink load in millisecond; 0 if load cannot be determined. |
| 1.3.6.1.4.1.28097.10.10.13 | TableconfigHS20ProfileOperClassTable | not-accessible | current | List of configHS20ProfileOperClassTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.13.1 | RowconfigHS20ProfileOperClassEntry | not-accessible | current | List of configHS20ProfileOperClass [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.13.1.1 | ColumnconfigProfileOperClassName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.13.1.2 | ColumnconfigProfileOperClassRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.13.1.3 | ColumnconfigProfileOperClassDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.13.1.4 | ColumnconfigOperClassList | read-write | current | Operating class list |
| 1.3.6.1.4.1.28097.10.10.14 | TableconfigHS20ProfileOsuProviderTable | not-accessible | current | List of configHS20ProfileOsuProviderTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.14.1 | RowconfigHS20ProfileOsuProviderEntry | not-accessible | current | List of configHS20ProfileOsuProvider [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.14.1.1 | ColumnconfigProfileOsuProviderName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.14.1.2 | ColumnconfigProfileOsuProviderRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.14.1.3 | ColumnconfigProfileOsuProviderDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.14.1.4 | ColumnconfigOsuServerUri | read-write | current | OSU server URI. |
| 1.3.6.1.4.1.28097.10.10.14.1.5 | ColumnconfigOsuFriendlyNameList | read-write | current | OSU provider friendly name list. |
| 1.3.6.1.4.1.28097.10.10.14.1.6 | ColumnconfigOsuNai | read-write | current | OSU NAI. |
| 1.3.6.1.4.1.28097.10.10.14.1.7 | ColumnconfigOsuOmaDm | read-write | current | Support OMA DM(Open Mobile Alliance Device Management). |
| 1.3.6.1.4.1.28097.10.10.14.1.8 | ColumnconfigOsuSoapXml | read-write | current | Supoort SOAP(Simple Object Access Protocol) XML. |
| 1.3.6.1.4.1.28097.10.10.14.1.9 | ColumnconfigOsuIconProfileList | read-write | current | Icon profile list. |
| 1.3.6.1.4.1.28097.10.10.14.1.10 | ColumnconfigOsuServiceDescList | read-write | current | Service description list. |
| 1.3.6.1.4.1.28097.10.10.15 | TableconfigProfileIconTable | not-accessible | current | List of configProfileIconTable [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.15.1 | RowconfigProfileIconEntry | not-accessible | current | List of configProfileIcon [FW:E2148.AC.1:X.XX.X.X] |
| 1.3.6.1.4.1.28097.10.10.15.1.1 | ColumnconfigProfileIconName | read-only | current | profile name, which will be referred in passpoint config. |
| 1.3.6.1.4.1.28097.10.10.15.1.2 | ColumnconfigProfileIconRowStatus | read-create | current | row addition/deletion support |
| 1.3.6.1.4.1.28097.10.10.15.1.3 | ColumnconfigProfileIconDesc | read-write | current | profile description. |
| 1.3.6.1.4.1.28097.10.10.15.1.4 | ColumnconfigIconLang | read-write | current | Language in which the icon will be shown. |
| 1.3.6.1.4.1.28097.10.10.15.1.5 | ColumnconfigIconSize | read-write | current | Icon size in pixel. <Icon Width>:<Icon Height> |
| 1.3.6.1.4.1.28097.10.10.15.1.6 | ColumnconfigIconType | read-write | current | MIME type of the icon file. |
| 1.3.6.1.4.1.28097.10.10.15.1.7 | ColumnconfigIconPath | read-only | current | Internal path of icon file. |
| 1.3.6.1.4.1.28097.10.10.15.1.8 | ColumnconfigIconFileContent | read-write | current | File content encoded in base64 |
| 1.3.6.1.4.1.28097.10.11 | Nodesc-async-sysupgrade | |||
| 1.3.6.1.4.1.28097.10.11.1 | ScalarconfigAsyncUpgradeDoUpgrade | read-write | current | Execute system upgrade immediately if there is a valid firmware uploaded. [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.10.11.2 | ScalarconfigAsyncUpgradeTimerEnable | read-write | current | Enable / disable the timer for system upgrade. [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.10.11.3 | ScalarconfigAsyncUpgradeTimerMode | read-write | current | Current timer mode. (Mode [Repeating-applied] cannot be set, it's get-only.) [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.10.11.4 | ScalarconfigAsyncUpgradeTimerMinute | read-write | current | Set minutes after [apply], system upgrade will be performed. [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.10.12 | Nodesc-md5sum | |||
| 1.3.6.1.4.1.28097.10.12.1 | ScalarconfigMD5SUMstatus | read-write | current | Set any value to re-calculate md5 sums of filesystem. Do a GET to get number of failed files. [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.10.12.2 | ScalarconfigMD5SUMfiles | read-only | current | Return the failed files list [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.11 | Nodenotification | |||
| 1.3.6.1.4.1.28097.11.1 | NotificationlinkAlarm | current | Ethernet or Wi-Fi link alarm (up or down) [FW:E2148.AC.1:2.8.0.1] | |
| 1.3.6.1.4.1.28097.11.3 | NotificationpowerAlarm | current | Power supply alarm. Only on products with 2 power supplies [FW:E2148.AC.1:2.8.0.1] | |
| 1.3.6.1.4.1.28097.11.4 | NotificationdigitalInputAlarm | current | Digital input alarm. Only on products with digital input [FW:E2148.AC.1:2.8.0.1] | |
| 1.3.6.1.4.1.28097.11.5 | NotificationtempExceededAlarm | current | Temperature alarm. The temperature exceeds the given trigger [FW:E2148.AC.1:2.8.0.1] | |
| 1.3.6.1.4.1.28097.11.6 | NotificationclientLinkAlarm | current | In AP mode, client was connected / disconnected [FW:E2148.AC.1:2.8.0.1] | |
| 1.3.6.1.4.1.28097.11.7 | NotificationvrrpAlarm | current | VRRP state change [FW:E2148.AC.1:2.8.0.1] | |
| 1.3.6.1.4.1.28097.11.8 | NotificationdfsAlarm | current | DFS alarm [FW:E2148.AC.1:2.8.0.1] | |
| 1.3.6.1.4.1.28097.11.9 | NotificationpingerAlarm | current | Notified if the hostname do not respond to the ping [FW:E2148.AC.1:2.8.0.1] | |
| 1.3.6.1.4.1.28097.11.11 | NotificationtcnAlarm | current | TCN state change alarm | |
| 1.3.6.1.4.1.28097.11.12 | NotificationsecurityAlarm | current | Security-related alarm | |
| 1.3.6.1.4.1.28097.11.255 | NodenotificationBindings | |||
| 1.3.6.1.4.1.28097.11.255.1 | ScalarnbClientMacAddress | accessible-for-notify | current | MAC address of the client connected to the AP. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.11.255.2 | ScalarnbSsid | accessible-for-notify | current | The SSID for which the trap was triggered [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.11.255.3 | ScalarnbBssid | accessible-for-notify | current | The BSSID for which the trap was triggered Warning, a 17-bytes column-separated string may be returned with this OID. [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.11.255.4 | ScalarnbEventState | accessible-for-notify | current | Notification state. Currently, possible values are 'up', 'down', 'connect', 'disconnect', 'DFS_CAC_STARTED', 'DFS_CAC_FINISHED', 'DFS_CAC_ABORTED', 'DFS_RADAR_… |
| 1.3.6.1.4.1.28097.11.255.5 | ScalarnbEventName | accessible-for-notify | current | User-provided name of the event trigger in the product configuration database [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.11.255.6 | ScalarnbRadioName | accessible-for-notify | current | Radio card name [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.11.255.7 | ScalarnbRadioMacAddress | accessible-for-notify | current | Radio card Mac address [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.11.255.8 | ScalarnbRadioChannel | accessible-for-notify | current | Current Radio channel [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.11.255.9 | ScalarnbRadioChannelWidth | accessible-for-notify | current | Current Radio channel width in Mhz [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.11.255.10 | ScalarnbRadarChannel | accessible-for-notify | current | Current Radar channel [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.11.255.11 | ScalarnbRadarChannelWidth | accessible-for-notify | current | Current Radar channel width in Mhz [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.11.255.12 | ScalarnbHostName | accessible-for-notify | current | Host name of the equipment that triggered an event on the product [FW:E2148.AC.1:2.8.0.1] |
| 1.3.6.1.4.1.28097.11.255.13 | ScalarnbDigitalInName | accessible-for-notify | current | Digital input name [FW:E2148.AC.1:3.16.0.1] |
| 1.3.6.1.4.1.28097.11.255.14 | ScalarnbTcnTaiIp | accessible-for-notify | current | TCN Ip address of ETBN train application interface |
| 1.3.6.1.4.1.28097.11.255.15 | ScalarnbTcnEtbnStatus | accessible-for-notify | current | TCN ETBN status |
| 1.3.6.1.4.1.28097.11.255.16 | ScalarnbTcnEtbnRole | accessible-for-notify | current | TCN ETBN role |
| 1.3.6.1.4.1.28097.11.255.17 | ScalarnbTcnEtbnTopoCnt | accessible-for-notify | current | TCN CRC32 of the discovered train network directory |
| 1.3.6.1.4.1.28097.11.255.18 | ScalarnbTcnEtbTopoCntState | accessible-for-notify | current | ETB topology count validity state: if it is invalid, this means that at least one ETB of the current Train Network Directory has left current stable topology (… |
| 1.3.6.1.4.1.28097.11.255.19 | ScalarnbTcnLengtheningFlag | accessible-for-notify | current | TCN lengthening flag |
| 1.3.6.1.4.1.28097.11.255.20 | ScalarnbTcnShorteningState | accessible-for-notify | current | TCN Shortening state |
| 1.3.6.1.4.1.28097.11.255.21 | ScalarnbTcnRadio1CouplingState | accessible-for-notify | current | TCN Radio coupling state |
| 1.3.6.1.4.1.28097.11.255.22 | ScalarnbTcnConsistCount | accessible-for-notify | current | Number of consists in the train |
| 1.3.6.1.4.1.28097.11.255.23 | ScalarnbTcnConsistPosition | accessible-for-notify | current | Consist position in the train |
| 1.3.6.1.4.1.28097.11.255.24 | ScalarnbDescription | accessible-for-notify | current | Any available details about the event triggering the trap [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.11.255.25 | ScalarnbTimestamp | accessible-for-notify | current | Time of the event triggering the trap. Time is in seconds since the Epoch (1/1/1970 00:00 UTC) - see POSIX Base Definitions. [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.11.255.26 | ScalarnbMacAddr | accessible-for-notify | current | The BSSID for which the trap was triggered Format is binary PhysAddr (contrary to nbBssid binding). [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.11.255.27 | ScalarnbSource | accessible-for-notify | current | A tag which identifies the origin of the event. [FW:E2148.AC.1:4.16.0.1] |
| 1.3.6.1.4.1.28097.12 | ScalaracksysProductSerialNumber | read-only | current | Returns the product serial number [FW:E2148.AC.1:2.8.0.1] |