ACLMGMT-MIB
375 objects
The structure of Access Control List information for the proprietary enterprise.
Imported Objects
| DLINK-ID-REC-MIB | dlink-common-mgmt |
| RFC1213-MIB | DisplayString |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-SMI | Counter32 Counter64 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | MacAddress RowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.171.12.9 | IdentityswAclMgmtMIB | The structure of Access Control List information for the proprietary enterprise. | ||
| 1.3.6.1.4.1.171.12.9.1 | NodeswAclCtrl | |||
| 1.3.6.1.4.1.171.12.9.1.1 | ScalarswCpuInterfacefilterState | read-write | current | Enable or disable CPU Interface Filtering (also called Software ACL). The default is disabled. If enabled, the filtering entries in the swAclRuleMgmt tables wi… |
| 1.3.6.1.4.1.171.12.9.1.2 | ScalarswACLTotalUsedRuleEntries | read-only | current | The total number of used ACL rule entries. |
| 1.3.6.1.4.1.171.12.9.1.3 | ScalarswACLTotalUnusedRuleEntries | read-only | current | The total number of unused ACL rule entries. |
| 1.3.6.1.4.1.171.12.9.2 | NodeswAclMaskMgmt | |||
| 1.3.6.1.4.1.171.12.9.2.1 | TableswACLEthernetTable | not-accessible | current | This table contains ACL mask Ethernet information. The access profile will be created on the switch to define which part of each incoming frame's layer 2 heade… |
| 1.3.6.1.4.1.171.12.9.2.1.1 | RowswACLEthernetEntry | not-accessible | current | A list of information about the ACL for Ethernet. |
| 1.3.6.1.4.1.171.12.9.2.1.1.1 | ColumnswACLEthernetProfileID | read-only | current | The ID of the ACL mask entry unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.2.1.1.2 | ColumnswACLEthernetUsevlan | read-create | current | Specifies that the switch will examine the VLAN part of each packet header. |
| 1.3.6.1.4.1.171.12.9.2.1.1.3 | ColumnswACLEthernetMacAddrMaskState | read-create | current | This object indicates the status of the MAC address mask. other (1) - Neither source MAC address nor destination MAC address are masked. dst-mac-addr (2) - Des… |
| 1.3.6.1.4.1.171.12.9.2.1.1.4 | ColumnswACLEthernetSrcMacAddrMask | read-create | current | This object specifies the MAC address mask for the source MAC address. |
| 1.3.6.1.4.1.171.12.9.2.1.1.5 | ColumnswACLEthernetDstMacAddrMask | read-create | current | This object specifies the MAC address mask for the destination MAC address. |
| 1.3.6.1.4.1.171.12.9.2.1.1.6 | ColumnswACLEthernetUse8021p | read-create | current | Specifies if the switch will examine the 802.1p priority value in the frame's header or not. |
| 1.3.6.1.4.1.171.12.9.2.1.1.7 | ColumnswACLEthernetUseEthernetType | read-create | current | Specifies if the switch will examine the Ethernet type value in each frame's header or not. |
| 1.3.6.1.4.1.171.12.9.2.1.1.8 | ColumnswACLEthernetRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.2.1.1.9 | ColumnswACLEthernetOwner | read-only | current | The owner of the ACL mask entry. The type of ACL entry created. ACL type entries can only be modified when being configured through the same type command. For … |
| 1.3.6.1.4.1.171.12.9.2.1.1.10 | ColumnswACLEthernetUnusedRuleEntries | read-only | current | The number of unused rule entries of this Ethernet profile entry. |
| 1.3.6.1.4.1.171.12.9.2.1.1.11 | ColumnswACLEthernetProfileName | read-create | current | The name of the ACL mask entry unique to the mask list. |
| 1.3.6.1.4.1.171.12.9.2.2 | TableswACLIpTable | not-accessible | current | This table contains the ACL mask for IP information. Access profiles will be created on the switch to define which part of the incoming frame's IP layer packet… |
| 1.3.6.1.4.1.171.12.9.2.2.1 | RowswACLIpEntry | not-accessible | current | A list of information about the ACL of the IP Layer. |
| 1.3.6.1.4.1.171.12.9.2.2.1.1 | ColumnswACLIpProfileID | read-only | current | The ID of the ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.2.2.1.2 | ColumnswACLIpUsevlan | read-create | current | This object indicates if the IP layer VLAN part is examined or not. |
| 1.3.6.1.4.1.171.12.9.2.2.1.3 | ColumnswACLIpIpAddrMaskState | read-create | current | This object indicates the status of IP address mask. other (1) - Neither source IP address nor destination IP address are masked. dst-ip-addr (2) - Destination… |
| 1.3.6.1.4.1.171.12.9.2.2.1.4 | ColumnswACLIpSrcIpAddrMask | read-create | current | This object specifies the IP address mask for the source IP address. |
| 1.3.6.1.4.1.171.12.9.2.2.1.5 | ColumnswACLIpDstIpAddrMask | read-create | current | This object specifies the IP address mask for the destination IP address. |
| 1.3.6.1.4.1.171.12.9.2.2.1.6 | ColumnswACLIpUseDSCP | read-create | current | This object indicates if the DSCP protocol in the packet header is to be examined or not. |
| 1.3.6.1.4.1.171.12.9.2.2.1.7 | ColumnswACLIpUseProtoType | read-create | current | That object indicates which protocol will be examined. |
| 1.3.6.1.4.1.171.12.9.2.2.1.8 | ColumnswACLIpIcmpOption | read-create | current | This object indicates which fields are defined for ICMP. none (1)- Both fields are null. type (2)- Type field identified. code (3)- Code field identified. type… |
| 1.3.6.1.4.1.171.12.9.2.2.1.9 | ColumnswACLIpIgmpOption | read-create | current | Indicates if the IGMP options field is identified or not. |
| 1.3.6.1.4.1.171.12.9.2.2.1.10 | ColumnswACLIpTcpOption | read-create | current | This object indicates the status of the filtered address of TCP. other (1) - Neither source port nor destination port are masked. dst-addr (2) - Packets will b… |
| 1.3.6.1.4.1.171.12.9.2.2.1.11 | ColumnswACLIpUdpOption | read-create | current | This object indicates the status of the filtered address of UDP . other (1) - Neither source port nor destination port are masked. dst-addr (2) - Packets will … |
| 1.3.6.1.4.1.171.12.9.2.2.1.12 | ColumnswACLIpTCPorUDPSrcPortMask | read-create | current | Specifies a TCP port mask for the source port if swACLIpUseProtoType is TCP Specifies a UDP port mask for the source port if swACLIpUseProtoType is UDP. |
| 1.3.6.1.4.1.171.12.9.2.2.1.13 | ColumnswACLIpTCPorUDPDstPortMask | read-create | current | Specifies a TCP port mask for the destination port if swACLIpUseProtoType is TCP Specifies a UDP port mask for the destination port if swACLIpUseProtoType is U… |
| 1.3.6.1.4.1.171.12.9.2.2.1.14 | ColumnswACLIpTCPFlagBit | read-create | current | Specifies a TCP connection flag mask. |
| 1.3.6.1.4.1.171.12.9.2.2.1.15 | ColumnswACLIpTCPFlagBitMask | read-create | current | A value which indicates the set of TCP flags that this entity may potentially offer. The value is a sum of flag bits. This sum initially takes the value zero. … |
| 1.3.6.1.4.1.171.12.9.2.2.1.16 | ColumnswACLIpProtoIDOption | read-create | current | Specifies if the switch will examine each frame's protocol ID field or not. |
| 1.3.6.1.4.1.171.12.9.2.2.1.17 | ColumnswACLIpProtoID | read-create | current | Specifies that the rule applies to the IP protocol ID behind the IP header. |
| 1.3.6.1.4.1.171.12.9.2.2.1.18 | ColumnswACLIpProtoIDMask | read-create | current | Specifies that the rule applies to the IP protocol ID and the mask options behind the IP header. |
| 1.3.6.1.4.1.171.12.9.2.2.1.19 | ColumnswACLIpRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.2.2.1.20 | ColumnswACLIpOwner | read-only | current | The owner of the ACL mask entry. The type of ACL entry created. ACL type entries can only be modified when being configured through the same type command. For … |
| 1.3.6.1.4.1.171.12.9.2.2.1.22 | ColumnswACLIpUnusedRuleEntries | read-only | current | The number of unused rule entries this IP profile entry. |
| 1.3.6.1.4.1.171.12.9.2.2.1.23 | ColumnswACLIpProfileName | read-create | current | The name of the ACL mask entry unique to the mask list. |
| 1.3.6.1.4.1.171.12.9.2.3 | TableswACLPktContMaskTable | not-accessible | current | This table contains the ACL mask for user-defined information. An access profile will be created on the switch to define which part of each incoming frame's us… |
| 1.3.6.1.4.1.171.12.9.2.3.1 | RowswACLPktContMaskEntry | not-accessible | current | A list of information about user-defined ACLs. |
| 1.3.6.1.4.1.171.12.9.2.3.1.1 | ColumnswACLPktContMaskProfileID | read-only | current | The ID of the ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.2.3.1.2 | ColumnswACLPktContMaskOffset0to15 | read-create | current | Specifies that the rule applies to the packet content (Offset0to15) and the mask options. |
| 1.3.6.1.4.1.171.12.9.2.3.1.3 | ColumnswACLPktContMaskOffset16to31 | read-create | current | Specifies that the rule applies to the packet content (Offset16to31) and the mask options. |
| 1.3.6.1.4.1.171.12.9.2.3.1.4 | ColumnswACLPktContMaskOffset32to47 | read-create | current | Specifies that the rule applies to the packet content (Offset32to47) and the mask options. |
| 1.3.6.1.4.1.171.12.9.2.3.1.5 | ColumnswACLPktContMaskOffset48to63 | read-create | current | Specifies that the rule applies to the packet content (Offset48to63) and the mask options. |
| 1.3.6.1.4.1.171.12.9.2.3.1.6 | ColumnswACLPktContMaskOffset64to79 | read-create | current | Specifies that the rule applies to the packet content (Offset64to79) and the mask options. |
| 1.3.6.1.4.1.171.12.9.2.3.1.7 | ColumnswACLPktContMaskRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.2.3.1.8 | ColumnswACLPktContMaskOwner | read-only | current | The owner of the ACL mask entry. The type of ACL entry created. ACL type entries can only be modified when being configured through the same type command. For … |
| 1.3.6.1.4.1.171.12.9.2.3.1.9 | ColumnswACLPktContMaskUnusedRuleEntries | read-only | current | The number of unused rule entries of this IP profile entry. |
| 1.3.6.1.4.1.171.12.9.2.3.1.10 | ColumnswACLPktContMaskProfileName | read-create | current | The name of the ACL mask entry unique to the mask list. |
| 1.3.6.1.4.1.171.12.9.2.4 | TableswACLIpv6MaskTable | not-accessible | current | This table contains user-defined ACL mask information. An access profile will be created on the switch to define which parts of each incoming frame's IPv6 part… |
| 1.3.6.1.4.1.171.12.9.2.4.1 | RowswACLIpv6MaskEntry | not-accessible | current | A list of information about user-defined ACLs. |
| 1.3.6.1.4.1.171.12.9.2.4.1.1 | ColumnswACLIpv6MaskProfileID | read-only | current | The ID of the ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.2.4.1.2 | ColumnswACLIpv6MaskClass | read-create | current | Specifies that the rule applies to the IPv6 class field and the mask options. |
| 1.3.6.1.4.1.171.12.9.2.4.1.3 | ColumnswACLIpv6MaskFlowlabel | read-create | current | Specifies that the rule applies to the IPv6 flowlabel field and the mask options. |
| 1.3.6.1.4.1.171.12.9.2.4.1.4 | ColumnswACLIpv6IpAddrMaskState | read-create | current | This object indicates the status of the IPv6 address mask. other (1) - Neither source IPv6 address nor destination IPv6 address are masked. dst-ipv6-addr (2) -… |
| 1.3.6.1.4.1.171.12.9.2.4.1.5 | ColumnswACLIpv6MaskSrcIpv6Mask | read-create | current | Specifies that the rule applies to the Source IPv6 address and the mask options. This should be a 16 byte octet string. |
| 1.3.6.1.4.1.171.12.9.2.4.1.6 | ColumnswACLIpv6MaskDstIpv6Mask | read-create | current | Specifies that the rule applies to the Destination IPv6 address and the mask options. This should be a 16 byte octet string. |
| 1.3.6.1.4.1.171.12.9.2.4.1.7 | ColumnswACLIpv6MaskRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.2.4.1.8 | ColumnswACLIpv6MaskOwner | read-only | current | The owner of the ACL mask entry. The type of ACL entry created. ACL type entries can only be modified when being configured through the same type command. For … |
| 1.3.6.1.4.1.171.12.9.2.4.1.9 | ColumnswACLIpv6MaskUnusedRuleEntries | read-only | current | The number of unused rule entries of this IP profile entry. |
| 1.3.6.1.4.1.171.12.9.2.4.1.10 | ColumnswACLIpv6MaskProfileName | read-create | current | The name of the ACL mask entry unique to the mask list. |
| 1.3.6.1.4.1.171.12.9.2.4.1.11 | ColumnswACLIpv6MaskUseProtoType | read-create | current | That object indicates which protocol will be examined. |
| 1.3.6.1.4.1.171.12.9.2.4.1.12 | ColumnswACLIpv6MaskTcpOption | read-create | current | This object indicates the status of the filtered address of TCP. other (1) - Neither source port nor destination port are masked. dst-addr (2) - Packets will b… |
| 1.3.6.1.4.1.171.12.9.2.4.1.13 | ColumnswACLIpv6MaskUdpOption | read-create | current | This object indicates the status of the filtered address of UDP. other (1) - Neither source port nor destination port is masked. dst-addr (2) - Packets will be… |
| 1.3.6.1.4.1.171.12.9.2.4.1.14 | ColumnswACLIpv6MaskTCPorUDPSrcPortMask | read-create | current | Specifies a TCP port mask for the source port if swACLIpv6MaskUseProtoType is TCP Specifies a UDP port mask for the source port if swACLIpv6MaskUseProtoType is… |
| 1.3.6.1.4.1.171.12.9.2.4.1.15 | ColumnswACLIpv6MaskTCPorUDPDstPortMask | read-create | current | Specifies a TCP port mask for the destination port if swACLIpv6MaskUseProtoType is TCP Specifies a UDP port mask for the destination port if swACLIpv6MaskUsePr… |
| 1.3.6.1.4.1.171.12.9.2.5 | ScalarswACLMaskDelAllState | read-write | current | Used to delete all ACL masks. |
| 1.3.6.1.4.1.171.12.9.2.6 | TableswIBPACLEthernetTable | not-accessible | obsolete | This table contains IP-MAC-Binding ACL mask Ethernet information. Access profiles will be created on the switch by row creation and to define which parts of ea… |
| 1.3.6.1.4.1.171.12.9.2.6.1 | RowswIBPACLEthernetEntry | not-accessible | obsolete | A list of information about the Ethernet ACL. |
| 1.3.6.1.4.1.171.12.9.2.6.1.1 | ColumnswIBPACLEthernetProfileID | read-only | obsolete | The ID of the ACL mask entry, unique in the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.2.6.1.2 | ColumnswIBPACLEthernetUseEthernetType | read-only | obsolete | Specifies if the switch will examine the Ethernet type value in each frame's header or not. |
| 1.3.6.1.4.1.171.12.9.2.7 | TableswIBPACLIpTable | not-accessible | obsolete | This table contains IP-MAC-Binding IP ACL mask information. Access profiles will be created on the switch by row creation and to define which parts of each inc… |
| 1.3.6.1.4.1.171.12.9.2.7.1 | RowswIBPACLIpEntry | not-accessible | obsolete | A list of information about the IP layer of the ACL. |
| 1.3.6.1.4.1.171.12.9.2.7.1.1 | ColumnswIBPACLIpProfileID | read-only | obsolete | The ID of the ACL mask entry, unique in the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.2.7.1.2 | ColumnswIBPACLIpSrcMacAddrMask | read-only | obsolete | This object specifies the MAC address mask for the source MAC address. |
| 1.3.6.1.4.1.171.12.9.2.7.1.3 | ColumnswIBPACLIpSrcIpAddrMask | read-only | obsolete | This object specifies IP address masks for the source IP address. |
| 1.3.6.1.4.1.171.12.9.2.8 | TableswACLPktContMaskOptionTable | not-accessible | current | This table contains the ACL mask for user-defined option information. An access profile will be created on the switch to define which part of each incoming fra… |
| 1.3.6.1.4.1.171.12.9.2.8.1 | RowswACLPktContMaskOptionEntry | not-accessible | current | A list of information about the user-defined ACL. |
| 1.3.6.1.4.1.171.12.9.2.8.1.1 | ColumnswACLPktContMaskOptionProfileID | read-only | current | The ID of the ACL mask entry, unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.2.8.1.2 | ColumnswACLPktContMaskOffsetChunk1State | read-create | current | Specifies the state of chunk1. |
| 1.3.6.1.4.1.171.12.9.2.8.1.3 | ColumnswACLPktContMaskOffsetChunk1OffsetValue | read-create | current | Specifies the frame content offset of chunk1. |
| 1.3.6.1.4.1.171.12.9.2.8.1.4 | ColumnswACLPktContMaskOffsetChunk1Mask | read-create | current | Specifies the frame content mask of chunk1. |
| 1.3.6.1.4.1.171.12.9.2.8.1.5 | ColumnswACLPktContMaskOffsetChunk2State | read-create | current | Specifies the state of chunk2. |
| 1.3.6.1.4.1.171.12.9.2.8.1.6 | ColumnswACLPktContMaskOffsetChunk2OffsetValue | read-create | current | Specifies the frame content offset of chunk2. |
| 1.3.6.1.4.1.171.12.9.2.8.1.7 | ColumnswACLPktContMaskOffsetChunk2Mask | read-create | current | Specifies the frame content mask of chunk2. |
| 1.3.6.1.4.1.171.12.9.2.8.1.8 | ColumnswACLPktContMaskOffsetChunk3State | read-create | current | Specifies the state of chunk3. |
| 1.3.6.1.4.1.171.12.9.2.8.1.9 | ColumnswACLPktContMaskOffsetChunk3OffsetValue | read-create | current | Specifies the frame content offset of chunk3. |
| 1.3.6.1.4.1.171.12.9.2.8.1.10 | ColumnswACLPktContMaskOffsetChunk3Mask | read-create | current | Specifies the frame content mask of chunk3. |
| 1.3.6.1.4.1.171.12.9.2.8.1.11 | ColumnswACLPktContMaskOffsetChunk4State | read-create | current | Specifies the state of chunk4. |
| 1.3.6.1.4.1.171.12.9.2.8.1.12 | ColumnswACLPktContMaskOffsetChunk4OffsetValue | read-create | current | Specifies the frame content offset of chunk4. |
| 1.3.6.1.4.1.171.12.9.2.8.1.13 | ColumnswACLPktContMaskOffsetChunk4Mask | read-create | current | Specifies the frame content mask of chunk4. |
| 1.3.6.1.4.1.171.12.9.2.8.1.14 | ColumnswACLPktContMaskOptionRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.2.8.1.15 | ColumnswACLPktContMaskOptionOwner | read-only | current | The owner of the ACL mask entry. The type of ACL entry created. ACL type entries can only be modified when being configured through the same type command. For … |
| 1.3.6.1.4.1.171.12.9.2.8.1.16 | ColumnswACLPktContMaskOptionUnusedRuleEntries | read-only | current | The number of unused rule entries of this IP profile entry. |
| 1.3.6.1.4.1.171.12.9.2.8.1.17 | ColumnswACLPktContMaskOptionProfileName | read-create | current | The name of the ACL mask entry unique to the mask list. |
| 1.3.6.1.4.1.171.12.9.3 | NodeswAclRuleMgmt | |||
| 1.3.6.1.4.1.171.12.9.3.1 | TableswACLEtherRuleTable | not-accessible | current | This table contains Ethernet ACL information. |
| 1.3.6.1.4.1.171.12.9.3.1.1 | RowswACLEtherRuleEntry | not-accessible | current | A list of information about the ACL rule of the layer 2 part of each packet. |
| 1.3.6.1.4.1.171.12.9.3.1.1.1 | ColumnswACLEtherRuleProfileID | read-only | current | The ID of the ACL rule entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.3.1.1.2 | ColumnswACLEtherRuleAccessID | read-only | current | The ID of the the ACL rule entry relates to the swACLEtherRuleProfileID. When row creation is set to 0, assignment of an Access ID for ports is automatic and t… |
| 1.3.6.1.4.1.171.12.9.3.1.1.3 | ColumnswACLEtherRuleVlan | read-create | current | Specifies that the access rule will apply to this VLAN only. |
| 1.3.6.1.4.1.171.12.9.3.1.1.4 | ColumnswACLEtherRuleSrcMacAddress | read-create | current | Specifies that the access rule will apply to only packets with this source MAC address. |
| 1.3.6.1.4.1.171.12.9.3.1.1.5 | ColumnswACLEtherRuleDstMacAddress | read-create | current | Specifies that the access rule will apply to only packets with this destination MAC address. |
| 1.3.6.1.4.1.171.12.9.3.1.1.6 | ColumnswACLEtherRule8021P | read-create | current | Specifies that the access rule will apply only to packets with this 802.1p priority value. A value of -1 indicates that this node is not actively used. |
| 1.3.6.1.4.1.171.12.9.3.1.1.7 | ColumnswACLEtherRuleEtherType | read-create | current | Specifies that the access rule will apply only to packets with this hexadecimal 802.1Q Ethernet type value in the packet header. |
| 1.3.6.1.4.1.171.12.9.3.1.1.8 | ColumnswACLEtherRuleEnablePriority | read-create | current | Specifies that the access rule will apply only to packets with priority value. |
| 1.3.6.1.4.1.171.12.9.3.1.1.9 | ColumnswACLEtherRulePriority | read-create | current | Specifies that the priority will be changed in packets while the swACLEtherRuleEnablePriority is enabled . |
| 1.3.6.1.4.1.171.12.9.3.1.1.10 | ColumnswACLEtherRuleReplacePriority | read-create | current | Specifies if the switch will change priorities of packets that match the access profile 802.1p priority tag field or not . |
| 1.3.6.1.4.1.171.12.9.3.1.1.11 | ColumnswACLEtherRuleEnableReplaceDscp | read-create | current | Specifies if the switch will change priorities of packets that match the access profile DSCP field or not. Replace DSCP and replace ToS precedence can not both… |
| 1.3.6.1.4.1.171.12.9.3.1.1.12 | ColumnswACLEtherRuleRepDscp | read-create | current | Specifies a value to be written to the DSCP field of an incoming packet that meets the criteria specified in the first part of the command. This value will ove… |
| 1.3.6.1.4.1.171.12.9.3.1.1.13 | ColumnswACLEtherRulePermit | read-create | current | This object indicates if the result of the packet examination is 'permit' or 'deny'. The default is 'permit'. permit - Specifies that packets that match the ac… |
| 1.3.6.1.4.1.171.12.9.3.1.1.14 | ColumnswACLEtherRulePort | read-create | current | Specifies that the access rule will only apply to port(s). This object and swACLEtherRuleVID can not be set together. |
| 1.3.6.1.4.1.171.12.9.3.1.1.15 | ColumnswACLEtherRuleRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.3.1.1.16 | ColumnswACLEtherRuleOwner | read-only | current | The owner of the ACL rule entry. Only owners can modify this entry. |
| 1.3.6.1.4.1.171.12.9.3.1.1.17 | ColumnswACLEtherRuleRxRate | read-create | current | Specifies the rx rate, 0 denotes no_limit. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.3.1.1.18 | ColumnswACLEtherRuleEnableReplaceTosPrecedence | read-create | current | Specifies if the switch will change priorities of packets that match the access profile ToS precedence field or not. Replace DSCP and replace ToS precedence ca… |
| 1.3.6.1.4.1.171.12.9.3.1.1.19 | ColumnswACLEtherRuleRepTosPrecedence | read-create | current | Specifies a value to be written to the ToS precedence field of an incoming packet that meets the criteria specified in the first part of the command. This valu… |
| 1.3.6.1.4.1.171.12.9.3.1.1.20 | ColumnswACLEtherRuleVID | read-create | current | Specifies this rule only applies to the specified VLAN. There are two conditions: 1.only the portlist that belongs to this VLAN will be included; 2.packets mus… |
| 1.3.6.1.4.1.171.12.9.3.2 | TableswACLIpRuleTable | not-accessible | current | |
| 1.3.6.1.4.1.171.12.9.3.2.1 | RowswACLIpRuleEntry | not-accessible | current | |
| 1.3.6.1.4.1.171.12.9.3.2.1.1 | ColumnswACLIpRuleProfileID | read-only | current | The ID of the ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.3.2.1.2 | ColumnswACLIpRuleAccessID | read-only | current | The ID of the ACL rule entry relates to swACLIPRuleProfileID. Row creation set to 0 indicates automatic assignment of the Access ID for the ports in the swACLI… |
| 1.3.6.1.4.1.171.12.9.3.2.1.3 | ColumnswACLIpRuleVlan | read-create | current | Specifies that the access rule will only apply to this VLAN. |
| 1.3.6.1.4.1.171.12.9.3.2.1.4 | ColumnswACLIpRuleSrcIpaddress | read-create | current | Specifies an IP source address. |
| 1.3.6.1.4.1.171.12.9.3.2.1.5 | ColumnswACLIpRuleDstIpaddress | read-create | current | Specifies an IP destination address. |
| 1.3.6.1.4.1.171.12.9.3.2.1.6 | ColumnswACLIpRuleDscp | read-create | current | Specifies the value of DSCP. The value can be configured from 0 to 63. A value of -1 indicates that this node is not actively used. |
| 1.3.6.1.4.1.171.12.9.3.2.1.7 | ColumnswACLIpRuleProtocol | read-write | current | Specifies the IP protocol. For some older chips, this object can not be set. When getting this object, it always returns the type which has been configured in … |
| 1.3.6.1.4.1.171.12.9.3.2.1.8 | ColumnswACLIpRuleType | read-create | current | Specifies that the rule applies to the value of ICMP type traffic. A value of -1 denotes that this object is not active. |
| 1.3.6.1.4.1.171.12.9.3.2.1.9 | ColumnswACLIpRuleCode | read-create | current | Specifies that the rule applies to the value of ICMP code traffic. A value of -1 denotes that this object is not active. |
| 1.3.6.1.4.1.171.12.9.3.2.1.10 | ColumnswACLIpRuleSrcPort | read-create | current | Specifies that the rule applies to the range of the TCP/UDP source ports. A value of -1 indicates that this node is not actively used. |
| 1.3.6.1.4.1.171.12.9.3.2.1.11 | ColumnswACLIpRuleDstPort | read-create | current | Specifies the TCP/UDP destination port range. A value of -1 indicates that this node is not actively used. |
| 1.3.6.1.4.1.171.12.9.3.2.1.12 | ColumnswACLIpRuleFlagBits | read-create | current | A value which indicates the set of TCP flags that this entity may potentially offer. The value is a sum of flag bits. This sum initially takes the value zero. … |
| 1.3.6.1.4.1.171.12.9.3.2.1.13 | ColumnswACLIpRuleProtoID | read-create | current | Specifies that the rule applies to the value of IP protocol ID traffic. A value of -1 indicates that this node is not actively used. |
| 1.3.6.1.4.1.171.12.9.3.2.1.14 | ColumnswACLIpRuleUserMask | read-create | current | Specifies that the rule applies to the IP protocol ID and the range of options behind the IP header. |
| 1.3.6.1.4.1.171.12.9.3.2.1.15 | ColumnswACLIpRuleEnablePriority | read-create | current | Specifies that the access rule will apply only to packets with this priority value. |
| 1.3.6.1.4.1.171.12.9.3.2.1.16 | ColumnswACLIpRulePriority | read-create | current | Specifies the priority will change in packets while the swACLIpRuleEnablePriority is enabled. |
| 1.3.6.1.4.1.171.12.9.3.2.1.17 | ColumnswACLIpRuleReplacePriority | read-create | current | Specifies whether the packets that match the access profile will change the 802.1p priority tag field by the switch or not. |
| 1.3.6.1.4.1.171.12.9.3.2.1.18 | ColumnswACLIpRuleEnableReplaceDscp | read-create | current | Specifies if the switch will change priorities of packets that match the access profile DSCP field or not. Replace DSCP and replace ToS precedence can not both… |
| 1.3.6.1.4.1.171.12.9.3.2.1.19 | ColumnswACLIpRuleRepDscp | read-create | current | Specifies a value to be written to the DSCP field of an incoming packet that meets the criteria specified in the first part of the command. This value will ove… |
| 1.3.6.1.4.1.171.12.9.3.2.1.20 | ColumnswACLIpRulePermit | read-create | current | This object indicates if the result of the packet examination is to 'permit' or 'deny'. The default is 'permit'. permit - Specifies that packets that match the… |
| 1.3.6.1.4.1.171.12.9.3.2.1.21 | ColumnswACLIpRulePort | read-create | current | Specifies that the access rule will only apply to port(s). This object and swACLIpRuleVID can not be set together. |
| 1.3.6.1.4.1.171.12.9.3.2.1.22 | ColumnswACLIpRuleRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.3.2.1.23 | ColumnswACLIpRuleOwner | read-only | current | The owner of the ACL rule entry. Only owners can modify this entry. |
| 1.3.6.1.4.1.171.12.9.3.2.1.24 | ColumnswACLIpRuleRxRate | read-create | current | Specifies the rx-rate, 0 denotes no_limit. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.3.2.1.26 | ColumnswACLIpRuleEnableReplaceTosPrecedence | read-create | current | Specifies if the switch will change priorities of packets that match the access profile ToS precedence field or not. Replace DSCP and replace ToS precedence ca… |
| 1.3.6.1.4.1.171.12.9.3.2.1.27 | ColumnswACLIpRuleRepTosPrecedence | read-create | current | Specifies a value to be written to the ToS precedence field of an incoming packet that meets the criteria specified in the first part of the command. This valu… |
| 1.3.6.1.4.1.171.12.9.3.2.1.28 | ColumnswACLIpRuleVID | read-create | current | Specifies this rule only applies to the specified VLAN. There are two conditions: 1.only the portlist that belongs to this VLAN will be included; 2.packets mus… |
| 1.3.6.1.4.1.171.12.9.3.4 | TableswACLIpv6RuleTable | not-accessible | current | This table contains the IPv6 ACL rule information. |
| 1.3.6.1.4.1.171.12.9.3.4.1 | RowswACLIpv6RuleEntry | not-accessible | current | A list of information about ACL rules regarding the IPv6 part of each packet. |
| 1.3.6.1.4.1.171.12.9.3.4.1.1 | ColumnswACLIpv6RuleProfileID | read-only | current | The ID of the ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.3.4.1.2 | ColumnswACLIpv6RuleAccessID | read-only | current | The ID of the ACL rule entry relates to swACLIpv6RuleProfileID. When row creation is set to 0, this indicates the access ID will be assigned automatically for … |
| 1.3.6.1.4.1.171.12.9.3.4.1.3 | ColumnswACLIpv6RuleClass | read-create | current | Specifies that the rule applies to the IPv6 class field. |
| 1.3.6.1.4.1.171.12.9.3.4.1.4 | ColumnswACLIpv6RuleFlowlabel | read-create | current | Specifies that the rule applies to the IPv6 flow label field. |
| 1.3.6.1.4.1.171.12.9.3.4.1.5 | ColumnswACLIpv6RuleSrcIpv6Addr | read-create | current | Specifies that the rule applies to the source IPv6 address. This should be a 16 byte octet string. |
| 1.3.6.1.4.1.171.12.9.3.4.1.6 | ColumnswACLIpv6RuleDstIpv6Addr | read-create | current | Specifies that the rule applies to the destination IPv6 address. This should be a 16 byte octet string. |
| 1.3.6.1.4.1.171.12.9.3.4.1.7 | ColumnswACLIpv6RuleEnablePriority | read-create | current | Specifies that the access rule will apply only to packets with priority value. |
| 1.3.6.1.4.1.171.12.9.3.4.1.8 | ColumnswACLIpv6RulePriority | read-create | current | Specifies the priority will change in packets while the swACLIpv6RuleReplacePriority is enabled. |
| 1.3.6.1.4.1.171.12.9.3.4.1.9 | ColumnswACLIpv6RuleReplacePriority | read-create | current | Specifies if the switch will change priorities of packets that match the access profile 802.1p priority tag or not. |
| 1.3.6.1.4.1.171.12.9.3.4.1.10 | ColumnswACLIpv6RulePermit | read-create | current | This object indicates if the result of packet examination is to 'permit' or 'deny'. The default is 'permit'. permit - Specifies that packets that match the acc… |
| 1.3.6.1.4.1.171.12.9.3.4.1.11 | ColumnswACLIpv6RulePort | read-create | current | Specifies that the access rule will apply only to port(s). This object and swACLIpv6RuleVID can not be set together. |
| 1.3.6.1.4.1.171.12.9.3.4.1.12 | ColumnswACLIpv6RuleRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.3.4.1.13 | ColumnswACLIpv6RuleOwner | read-only | current | The owner of the ACL rule entry. Only owners can modify this entry. |
| 1.3.6.1.4.1.171.12.9.3.4.1.14 | ColumnswACLIpv6RuleRxRate | read-create | current | Specifies the rx-rate, 0 denotes no_limit. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.3.4.1.15 | ColumnswACLIpv6RuleEnableReplaceDscp | read-create | current | Specifies if the switch will change priorities of packets that match the access profile DSCP field or not. Replace DSCP and replace ToS precedence can not both… |
| 1.3.6.1.4.1.171.12.9.3.4.1.16 | ColumnswACLIpv6RuleRepDscp | read-create | current | Specifies a value to be written to the DSCP field of an incoming packet that meets the criteria specified in the first part of the command. This value will ove… |
| 1.3.6.1.4.1.171.12.9.3.4.1.17 | ColumnswACLIpv6RuleEnableReplaceTosPrecedence | read-create | current | Specifies if the switch will change priorities of packets that match the access profile ToS precedence field or not. Replace DSCP and replace ToS precedence ca… |
| 1.3.6.1.4.1.171.12.9.3.4.1.18 | ColumnswACLIpv6RuleRepTosPrecedence | read-create | current | Specifies a value to be written to the ToS precedence field of an incoming packet that meets the criteria specified in the first part of the command. This valu… |
| 1.3.6.1.4.1.171.12.9.3.4.1.19 | ColumnswACLIpv6RuleVID | read-create | current | Specifies this rule only applies to the specified VLAN. There are two conditions: 1.only the portlist that belongs to this VLAN will be included; 2.packets mus… |
| 1.3.6.1.4.1.171.12.9.3.4.1.20 | ColumnswACLIpv6RuleProtocol | read-create | current | Specifies the IPv6 protocol. For some older chips, this object can not be set. When getting this object, it always returns the type which has been configured i… |
| 1.3.6.1.4.1.171.12.9.3.4.1.21 | ColumnswACLIpv6RuleSrcPort | read-create | current | Specifies that the rule applies to the range of the TCP/UDP source ports. |
| 1.3.6.1.4.1.171.12.9.3.4.1.22 | ColumnswACLIpv6RuleDstPort | read-create | current | Specifies the TCP/UDP destination ports range. |
| 1.3.6.1.4.1.171.12.9.3.5 | TableswIBPACLEtherRuleTable | not-accessible | obsolete | This table contains IP-MAC-Binding Ethernet ACL Rule information. |
| 1.3.6.1.4.1.171.12.9.3.5.1 | RowswIBPACLEtherRuleEntry | not-accessible | obsolete | A list of information about the ACL rule of the layer 2 part of each packet. |
| 1.3.6.1.4.1.171.12.9.3.5.1.1 | ColumnswIBPACLEtherRuleProfileID | read-only | obsolete | The ID of the ACL mask entry, unique in the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.3.5.1.2 | ColumnswIBPACLEtherRuleAccessID | read-only | obsolete | The ID of the ACL rule entry in relation to swACLEtherRuleProfileID. When row creation is set to 0, this indicates automatically assigning an Access for the po… |
| 1.3.6.1.4.1.171.12.9.3.5.1.3 | ColumnswIBPACLEtherRuleEtherType | read-only | obsolete | Specifies that the access rule will apply only to packets with this 802.1Q Ethernet type value in the packet header. |
| 1.3.6.1.4.1.171.12.9.3.5.1.4 | ColumnswIBPACLEtherRulePermit | read-only | obsolete | This object indicates if the result of the examination is 'permit' or 'deny'. The default is 'permit' (1). permit - Specifies that packets that match the acces… |
| 1.3.6.1.4.1.171.12.9.3.5.1.5 | ColumnswIBPACLEtherRulePort | read-only | obsolete | Specifies that the access rule will only apply to port(s). |
| 1.3.6.1.4.1.171.12.9.3.6 | TableswIBPACLIpRuleTable | not-accessible | obsolete | |
| 1.3.6.1.4.1.171.12.9.3.6.1 | RowswIBPACLIpRuleEntry | not-accessible | obsolete | |
| 1.3.6.1.4.1.171.12.9.3.6.1.1 | ColumnswIBPACLIpRuleProfileID | read-only | obsolete | The ID of the ACL mask entry, unique in the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.3.6.1.2 | ColumnswIBPACLIpRuleAccessID | read-only | obsolete | The ID of the ACL rule entry in relation to swACLIPRuleProfileID. When the row creation is set to 0, this indicates assigning an access ID automatically for th… |
| 1.3.6.1.4.1.171.12.9.3.6.1.3 | ColumnswIBPACLIpRuleSrcMacAddress | read-only | obsolete | Specifies that the access rule will apply to only packets with this source MAC address. |
| 1.3.6.1.4.1.171.12.9.3.6.1.4 | ColumnswIBPACLIpRuleSrcIpaddress | read-only | obsolete | Specifies an IP source address. |
| 1.3.6.1.4.1.171.12.9.3.6.1.5 | ColumnswIBPACLIpRulePermit | read-only | obsolete | This object indicates if the result of the examination is 'permit' or 'deny'; the default is 'permit' (1) permit - Specifies that packets that match the access… |
| 1.3.6.1.4.1.171.12.9.3.6.1.6 | ColumnswIBPACLIpRulePort | read-only | obsolete | Specifies that the access rule will only apply to port(s). |
| 1.3.6.1.4.1.171.12.9.3.8 | TableswACLCounterTable | not-accessible | current | This table maintains counter information associated with a specific rule in the ACL rule table. Please refer to the swACLEtherRuleTable, swACLIpRuleTable, swAC… |
| 1.3.6.1.4.1.171.12.9.3.8.1 | RowswACLCounterEntry | not-accessible | current | The entry maintains counter information associated with the ACL rule table. |
| 1.3.6.1.4.1.171.12.9.3.8.1.1 | ColumnswACLCounterProfileID | read-only | current | The ID of the ACL mask entry, which is unique in the mask list. |
| 1.3.6.1.4.1.171.12.9.3.8.1.2 | ColumnswACLCounterAccessID | read-only | current | The ID of the ACL rule entry as related to the swACLCounterProfileID. |
| 1.3.6.1.4.1.171.12.9.3.8.1.3 | ColumnswACLCounterState | read-write | current | Specifies whether the counter feature will be enabled/disabled. 1. This is optional. The default is disable. 2. If the rule is not bound with flow_meter, then … |
| 1.3.6.1.4.1.171.12.9.3.8.1.4 | ColumnswACLCounterTotalCounter | read-only | current | The number of matched packets. |
| 1.3.6.1.4.1.171.12.9.3.8.1.5 | ColumnswACLCounterGreenCounter | read-only | current | The number of matched green packets. |
| 1.3.6.1.4.1.171.12.9.3.8.1.6 | ColumnswACLCounterYellowCounter | read-only | current | The number of matched yellow packets. |
| 1.3.6.1.4.1.171.12.9.3.8.1.7 | ColumnswACLCounterRedCounter | read-only | current | The number of matched red packets. |
| 1.3.6.1.4.1.171.12.9.3.9 | TableswACLPktContRuleVarOffsetTable | not-accessible | current | This table is used to configure ACL user defined packet content rules for devices that support limited selection of packet content. |
| 1.3.6.1.4.1.171.12.9.3.9.1 | RowswACLPktContRuleVarOffsetEntry | not-accessible | current | A list which contains information on the ACL rules for user-defined parts of a packet. |
| 1.3.6.1.4.1.171.12.9.3.9.1.1 | ColumnswACLPktContRuleVarOffsetProfileID | read-only | current | The ID of ACL mask entry, which is unique to the mask list. |
| 1.3.6.1.4.1.171.12.9.3.9.1.2 | ColumnswACLPktContRuleVarOffsetAccessID | read-only | current | The ID of ACL rule entry related to swACLPktContRuleVarOffsetProfileID. |
| 1.3.6.1.4.1.171.12.9.3.9.1.8 | ColumnswACLPktContRuleVarOffsetOffsetIndex1 | read-create | current | Specifies the first offset will apply in getting the mask for this rule. |
| 1.3.6.1.4.1.171.12.9.3.9.1.9 | ColumnswACLPktContRuleVarOffsetMask1 | read-only | current | Display the mask for this rule. This mask corresponds to swACLPktContRuleVarOffsetOffsetIndex1 and swACLPktContRuleVarOffsetData1. |
| 1.3.6.1.4.1.171.12.9.3.9.1.10 | ColumnswACLPktContRuleVarOffsetData1 | read-create | current | Specifies the data for this rule. This rule relates to swACLPktContRuleVarOffsetOffsetIndex1 and swACLPktContRuleVarOffsetMask1. |
| 1.3.6.1.4.1.171.12.9.3.9.1.11 | ColumnswACLPktContRuleVarOffsetOffsetIndex2 | read-create | current | Specifies the second offset will apply in getting the mask for this rule. |
| 1.3.6.1.4.1.171.12.9.3.9.1.12 | ColumnswACLPktContRuleVarOffsetMask2 | read-only | current | Display the mask for this rule. This mask corresponds to swACLPktContRuleVarOffsetOffsetIndex2 and swACLPktContRuleVarOffsetData2. |
| 1.3.6.1.4.1.171.12.9.3.9.1.13 | ColumnswACLPktContRuleVarOffsetData2 | read-create | current | Specifies the data for this rule. This rule relates to swACLPktContRuleVarOffsetOffsetIndex2 and swACLPktContRuleVarOffsetMask2. |
| 1.3.6.1.4.1.171.12.9.3.9.1.14 | ColumnswACLPktContRuleVarOffsetOffsetIndex3 | read-create | current | Specifies the third offset will apply in getting the mask for this rule. |
| 1.3.6.1.4.1.171.12.9.3.9.1.15 | ColumnswACLPktContRuleVarOffsetMask3 | read-only | current | Display the mask for this rule. This mask corresponds to swACLPktContRuleVarOffsetOffsetIndex3 and swACLPktContRuleVarOffsetData3. |
| 1.3.6.1.4.1.171.12.9.3.9.1.16 | ColumnswACLPktContRuleVarOffsetData3 | read-create | current | Specifies the data for this rule. This rule relates to swACLPktContRuleVarOffsetOffsetIndex3 and swACLPktContRuleVarOffsetMask3. |
| 1.3.6.1.4.1.171.12.9.3.9.1.17 | ColumnswACLPktContRuleVarOffsetOffsetIndex4 | read-create | current | Specifies the fourth offset will apply in getting the mask for this rule. |
| 1.3.6.1.4.1.171.12.9.3.9.1.18 | ColumnswACLPktContRuleVarOffsetMask4 | read-only | current | Display the mask for this rule. This mask corresponds to swACLPktContRuleVarOffsetOffsetIndex4 and swACLPktContRuleVarOffsetData4. |
| 1.3.6.1.4.1.171.12.9.3.9.1.19 | ColumnswACLPktContRuleVarOffsetData4 | read-create | current | Specifies the data for this rule. This rule relates to swACLPktContRuleVarOffsetOffsetIndex4 and swACLPktContRuleVarOffsetMask4. |
| 1.3.6.1.4.1.171.12.9.3.9.1.20 | ColumnswACLPktContRuleVarOffsetOffsetIndex5 | read-create | current | Specifies the fifth offset will apply in getting the mask for this rule. |
| 1.3.6.1.4.1.171.12.9.3.9.1.21 | ColumnswACLPktContRuleVarOffsetMask5 | read-only | current | Display the mask for this rule. This mask corresponds to swACLPktContRuleVarOffsetOffsetIndex5 and swACLPktContRuleVarOffsetData5. |
| 1.3.6.1.4.1.171.12.9.3.9.1.22 | ColumnswACLPktContRuleVarOffsetData5 | read-create | current | Specifies the data for this rule. This rule relates to swACLPktContRuleVarOffsetOffsetIndex5 and swACLPktContRuleVarOffsetMask5. |
| 1.3.6.1.4.1.171.12.9.3.9.1.23 | ColumnswACLPktContRuleVarOffsetEnablePriority | read-create | current | Specifies that the access rule will apply only to packets with this priority value. |
| 1.3.6.1.4.1.171.12.9.3.9.1.24 | ColumnswACLPktContRuleVarOffsetPriority | read-create | current | Specifies the priority will change to the packets. |
| 1.3.6.1.4.1.171.12.9.3.9.1.25 | ColumnswACLPktContRuleVarOffsetReplacePriority | read-create | current | Specifies if the switch will change priorities of packets that match the access profile 802.1p priority tag or not . |
| 1.3.6.1.4.1.171.12.9.3.9.1.28 | ColumnswACLPktContRuleVarOffsetRxRate | read-write | current | Specifies that the access rule will apply an RX rate. 0 denotes no limit. |
| 1.3.6.1.4.1.171.12.9.3.9.1.29 | ColumnswACLPktContRuleVarOffsetPermit | read-create | current | This object indicates the result of the packet examination is to permit or deny. The default is permit. permit - Specifies that packets that match the access p… |
| 1.3.6.1.4.1.171.12.9.3.9.1.30 | ColumnswACLPktContRuleVarOffsetPort | read-create | current | Specifies that the access rule will apply only to port(s). |
| 1.3.6.1.4.1.171.12.9.3.9.1.33 | ColumnswACLPktContRuleVarOffsetRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.3.9.1.34 | ColumnswACLPktContRuleVarOffsetReplacePriorityWith | read-create | current | The value of this node will be used to replace the 802.1p priority tag of the packet that matched the access profile. |
| 1.3.6.1.4.1.171.12.9.4 | NodeswCpuAclMaskMgmt | |||
| 1.3.6.1.4.1.171.12.9.4.1 | TableswCpuAclEthernetTable | not-accessible | current | This table contains software ACL mask Ethernet information. Access profiles will be created on the switch to define which part of each incoming frame's layer 2… |
| 1.3.6.1.4.1.171.12.9.4.1.1 | RowswCpuAclEthernetEntry | not-accessible | current | A list of information about Ethernet ACL masks. |
| 1.3.6.1.4.1.171.12.9.4.1.1.1 | ColumnswCpuAclEthernetProfileID | read-only | current | The ID of the software ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.4.1.1.2 | ColumnswCpuAclEthernetUsevlan | read-create | current | Specifies that the switch will examine the VLAN part of each packet header. |
| 1.3.6.1.4.1.171.12.9.4.1.1.3 | ColumnswCpuAclEthernetMacAddrMaskState | read-create | current | This object indicates the status of the MAC address mask. other (1) - Neither source MAC addresses nor destination MAC addresses are masked. dst-mac-addr (2) -… |
| 1.3.6.1.4.1.171.12.9.4.1.1.4 | ColumnswCpuAclEthernetSrcMacAddrMask | read-create | current | This object specifies the MAC address mask for the source MAC address. |
| 1.3.6.1.4.1.171.12.9.4.1.1.5 | ColumnswCpuAclEthernetDstMacAddrMask | read-create | current | This object specifies the MAC address mask for the destination MAC address. |
| 1.3.6.1.4.1.171.12.9.4.1.1.6 | ColumnswCpuAclEthernetUse8021p | read-create | current | Specifies if the switch will examine the 802.1p priority value in the frame's header or not. |
| 1.3.6.1.4.1.171.12.9.4.1.1.7 | ColumnswCpuAclEthernetUseEthernetType | read-create | current | Specifies if the switch will examine the Ethernet type value in each frame's header or not. |
| 1.3.6.1.4.1.171.12.9.4.1.1.8 | ColumnswCpuAclEthernetRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.4.2 | TableswCpuAclIpTable | not-accessible | current | This table contains software ACL mask IP information. Access profiles will be created on the switch to define which parts of each incoming frame's IP layer 2 h… |
| 1.3.6.1.4.1.171.12.9.4.2.1 | RowswCpuAclIpEntry | not-accessible | current | A list of information about the software ACL of the IP Layer. |
| 1.3.6.1.4.1.171.12.9.4.2.1.1 | ColumnswCpuAclIpProfileID | read-only | current | The ID of the software ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.4.2.1.2 | ColumnswCpuAclIpUsevlan | read-create | current | This object indicates if the IP layer VLAN part is examined or not. |
| 1.3.6.1.4.1.171.12.9.4.2.1.3 | ColumnswCpuAclIpIpAddrMaskState | read-create | current | This object indicates the status of IP address mask. other (1) - Neither source IP addresses nor destination IP address are masked. dst-ip-addr (2) - Destinati… |
| 1.3.6.1.4.1.171.12.9.4.2.1.4 | ColumnswCpuAclIpSrcIpAddrMask | read-create | current | This object specifies the IP address mask for the source IP address. |
| 1.3.6.1.4.1.171.12.9.4.2.1.5 | ColumnswCpuAclIpDstIpAddrMask | read-create | current | This object specifies the IP address mask for the destination IP address. |
| 1.3.6.1.4.1.171.12.9.4.2.1.6 | ColumnswCpuAclIpUseDSCP | read-create | current | This object indicates if the DSCP protocol in the packet header is to be examined or not. |
| 1.3.6.1.4.1.171.12.9.4.2.1.7 | ColumnswCpuAclIpUseProtoType | read-create | current | This object indicates which protocol will be examined. |
| 1.3.6.1.4.1.171.12.9.4.2.1.8 | ColumnswCpuAclIpIcmpOption | read-create | current | This object indicates which fields are identified for ICMP. none (1)- Both fields are null. type (2)- Type field identified. code (3)- Code field identified. t… |
| 1.3.6.1.4.1.171.12.9.4.2.1.9 | ColumnswCpuAclIpIgmpOption | read-create | current | This object indicates if the IGMP options field is identified or not. |
| 1.3.6.1.4.1.171.12.9.4.2.1.10 | ColumnswCpuAclIpTcpOption | read-create | current | This object indicates the status of filtered addresses of TCP. other (1) - Neither source port nor destination port are masked. dst-addr (2) - Packets will be … |
| 1.3.6.1.4.1.171.12.9.4.2.1.11 | ColumnswCpuAclIpUdpOption | read-create | current | This object indicates the status of filtered addresses of UDP. other (1) - Neither source port nor destination port are masked. dst-addr (2) - Packets will be … |
| 1.3.6.1.4.1.171.12.9.4.2.1.12 | ColumnswCpuAclIpTCPorUDPSrcPortMask | read-create | current | Specifies a TCP port mask for the source port if swCpuAclIpUseProtoType is TCP. Specifies a UDP port mask for the source port if swCpuAclIpUseProtoType is UDP. |
| 1.3.6.1.4.1.171.12.9.4.2.1.13 | ColumnswCpuAclIpTCPorUDPDstPortMask | read-create | current | Specifies a TCP port mask for the destination port if swCpuAclIpUseProtoType is TCP. Specifies a UDP port mask for the destination port if swCpuAclIpUseProtoTy… |
| 1.3.6.1.4.1.171.12.9.4.2.1.14 | ColumnswCpuAclIpTCPFlagBit | read-create | current | Specifies a TCP connection flag mask. |
| 1.3.6.1.4.1.171.12.9.4.2.1.15 | ColumnswCpuAclIpTCPFlagBitMask | read-create | current | A value which indicates the set of TCP flags that this entity may potentially offer. The value is a sum of flag bits. This sum initially takes the value zero. … |
| 1.3.6.1.4.1.171.12.9.4.2.1.16 | ColumnswCpuAclIpProtoIDOption | read-create | current | Specifies if the switch will examine each frame's Protocol ID field or not. |
| 1.3.6.1.4.1.171.12.9.4.2.1.17 | ColumnswCpuAclIpProtoID | read-create | current | |
| 1.3.6.1.4.1.171.12.9.4.2.1.18 | ColumnswCpuAclIpProtoIDMask | read-create | current | Specifies that the rule applies to the IP protocol ID and the mask options behind the IP header. |
| 1.3.6.1.4.1.171.12.9.4.2.1.19 | ColumnswCpuAclIpRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.4.3 | TableswCpuAclPktContMaskTable | not-accessible | current | This table contains user-defined software ACL information. Access profiles will be created on the switch to define which part of each incoming frame's user-def… |
| 1.3.6.1.4.1.171.12.9.4.3.1 | RowswCpuAclPktContMaskEntry | not-accessible | current | A list of information about user-defined software ACLs. |
| 1.3.6.1.4.1.171.12.9.4.3.1.1 | ColumnswCpuAclPktContMaskProfileID | read-only | current | The ID of the software ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.4.3.1.2 | ColumnswCpuAclPktContMaskOffset0to15 | read-create | current | Specifies that the rule applies to the packet content (Offset0to15) and the mask options. |
| 1.3.6.1.4.1.171.12.9.4.3.1.3 | ColumnswCpuAclPktContMaskOffset16to31 | read-create | current | Specifies that the rule applies to the packet content (Offset16to31) and the mask options. |
| 1.3.6.1.4.1.171.12.9.4.3.1.4 | ColumnswCpuAclPktContMaskOffset32to47 | read-create | current | Specifies that the rule applies to the packet content (Offset32to47) and the mask options. |
| 1.3.6.1.4.1.171.12.9.4.3.1.5 | ColumnswCpuAclPktContMaskOffset48to63 | read-create | current | Specifies that the rule applies to the packet content (Offset48to63) and the mask options. |
| 1.3.6.1.4.1.171.12.9.4.3.1.6 | ColumnswCpuAclPktContMaskOffset64to79 | read-create | current | Specifies that the rule applies to the packet content (Offset64to79) and the mask options. |
| 1.3.6.1.4.1.171.12.9.4.3.1.7 | ColumnswCpuAclPktContMaskRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.4.4 | TableswCpuAclIpv6MaskTable | not-accessible | current | This table contains IPv6 software ACL mask information. An access profile will be created on the switch to define which part of each incoming frame's IPv6 part… |
| 1.3.6.1.4.1.171.12.9.4.4.1 | RowswCpuAclIpv6MaskEntry | not-accessible | current | A list of information about user-defined software ACLs. |
| 1.3.6.1.4.1.171.12.9.4.4.1.1 | ColumnswCpuAclIpv6MaskProfileID | read-only | current | The ID of the software ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.4.4.1.2 | ColumnswCpuAclIpv6MaskClass | read-create | current | Specifies that the rule applies to the IPv6 class field and the mask options. |
| 1.3.6.1.4.1.171.12.9.4.4.1.3 | ColumnswCpuAclIpv6MaskFlowlabel | read-create | current | Specifies that the rule applies to the IPv6 flowlabel field and the mask options. |
| 1.3.6.1.4.1.171.12.9.4.4.1.4 | ColumnswCpuAclIpv6IpAddrMaskState | read-create | current | This object indicates the status of IPv6 address mask. other (1) - Neither source IPv6 address nor destination IPv6 address are masked. dst-ipv6-addr (2) - Pac… |
| 1.3.6.1.4.1.171.12.9.4.4.1.5 | ColumnswCpuAclIpv6MaskSrcIpv6Mask | read-create | current | Specifies that the rule applies to the source IPv6 address and the mask options. This should be a 16 byte octet string. |
| 1.3.6.1.4.1.171.12.9.4.4.1.6 | ColumnswCpuAclIpv6MaskDstIpv6Mask | read-create | current | Specifies that the rule applies to the destination IPv6 address and the mask options. This should be a 16 byte octet string. |
| 1.3.6.1.4.1.171.12.9.4.4.1.7 | ColumnswCpuAclIpv6MaskRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.4.5 | ScalarswCpuACLMaskDelAllState | read-write | current | Used to delete all software ACL masks. |
| 1.3.6.1.4.1.171.12.9.5 | NodeswCpuAclRuleMgmt | |||
| 1.3.6.1.4.1.171.12.9.5.1 | TableswCpuAclEtherRuleTable | not-accessible | current | This table contains Ethernet software ACL rule information. |
| 1.3.6.1.4.1.171.12.9.5.1.1 | RowswCpuAclEtherRuleEntry | not-accessible | current | A list of information about the software ACL rule of the layer 2 part of each packet. |
| 1.3.6.1.4.1.171.12.9.5.1.1.1 | ColumnswCpuAclEtherRuleProfileID | read-only | current | The ID of the software ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.5.1.1.2 | ColumnswCpuAclEtherRuleAccessID | read-only | current | The ID of the software ACL rule entry as it relates to swCpuAclEtherRuleProfileID. |
| 1.3.6.1.4.1.171.12.9.5.1.1.3 | ColumnswCpuAclEtherRuleVlan | read-create | current | Specifies that the access rule will only apply to this VLAN. |
| 1.3.6.1.4.1.171.12.9.5.1.1.4 | ColumnswCpuAclEtherRuleSrcMacAddress | read-create | current | Specifies that the access rule will only apply to the packets with this source MAC address. |
| 1.3.6.1.4.1.171.12.9.5.1.1.5 | ColumnswCpuAclEtherRuleDstMacAddress | read-create | current | Specifies that the access rule will only apply to the packets with this destination MAC address. |
| 1.3.6.1.4.1.171.12.9.5.1.1.6 | ColumnswCpuAclEtherRule8021P | read-create | current | Specifies that the access rule will only apply to packets with this 802.1p priority value. A value of -1 indicates that this node is not actively used. |
| 1.3.6.1.4.1.171.12.9.5.1.1.7 | ColumnswCpuAclEtherRuleEtherType | read-create | current | Specifies that the access rule will only apply to packets with this 802.1Q Ethernet type value in the packet header. |
| 1.3.6.1.4.1.171.12.9.5.1.1.8 | ColumnswCpuAclEtherRulePermit | read-create | current | This object indicates if the result of the packet examination is to 'permit' or 'deny'. The default is 'permit'. permit - Specifies that packets that match the… |
| 1.3.6.1.4.1.171.12.9.5.1.1.9 | ColumnswCpuAclEtherRuleRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.5.1.1.10 | ColumnswCpuAclEtherRulePort | read-create | current | Specifies that the access rule will only apply to port(s). |
| 1.3.6.1.4.1.171.12.9.5.2 | TableswCpuAclIpRuleTable | not-accessible | current | This table contains IPv4 software ACL rule information. |
| 1.3.6.1.4.1.171.12.9.5.2.1 | RowswCpuAclIpRuleEntry | not-accessible | current | A list of information about this software ACL rule. |
| 1.3.6.1.4.1.171.12.9.5.2.1.1 | ColumnswCpuAclIpRuleProfileID | read-only | current | The ID of the software ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.5.2.1.2 | ColumnswCpuAclIpRuleAccessID | read-only | current | The ID of the software ACL for the IPv4 rule entry. |
| 1.3.6.1.4.1.171.12.9.5.2.1.3 | ColumnswCpuAclIpRuleVlan | read-create | current | Specifies that the access rule will apply only to this VLAN. |
| 1.3.6.1.4.1.171.12.9.5.2.1.4 | ColumnswCpuAclIpRuleSrcIpaddress | read-create | current | Specifies an IP source address. |
| 1.3.6.1.4.1.171.12.9.5.2.1.5 | ColumnswCpuAclIpRuleDstIpaddress | read-create | current | Specifies an IP destination address. |
| 1.3.6.1.4.1.171.12.9.5.2.1.6 | ColumnswCpuAclIpRuleDscp | read-create | current | Specifies the value of DSCP, the value can be configured from 0 to 63. A value of -1 indicates that this node is not actively used. |
| 1.3.6.1.4.1.171.12.9.5.2.1.7 | ColumnswCpuAclIpRuleProtocol | read-only | current | Specifies the IP protocol which has been configured in swCpuAclIpEntry. |
| 1.3.6.1.4.1.171.12.9.5.2.1.8 | ColumnswCpuAclIpRuleType | read-create | current | Specifies the rule applies to the value of ICMP type traffic. A value of -1 indicates that this node is not actively used. |
| 1.3.6.1.4.1.171.12.9.5.2.1.9 | ColumnswCpuAclIpRuleCode | read-create | current | Specifies the rule applies to the value of ICMP code traffic. A value of -1 indicates that this node is not actively used. |
| 1.3.6.1.4.1.171.12.9.5.2.1.10 | ColumnswCpuAclIpRuleSrcPort | read-create | current | Specifies the rule applies to the range of TCP/UDP source ports. A value of -1 indicates that this node is not actively used. |
| 1.3.6.1.4.1.171.12.9.5.2.1.11 | ColumnswCpuAclIpRuleDstPort | read-create | current | Specifies the range of TCP/UDP destination ports. A value of -1 indicates that this node is not actively used. |
| 1.3.6.1.4.1.171.12.9.5.2.1.12 | ColumnswCpuAclIpRuleFlagBits | read-create | current | A value which indicates the set of TCP flags that this entity may potentially offer. The value is a sum of flag bits. This sum initially takes the value zero. … |
| 1.3.6.1.4.1.171.12.9.5.2.1.13 | ColumnswCpuAclIpRuleProtoID | read-create | current | Specifies the rule applies to the value of IP protocol ID traffic. A value of -1 indicates that this node is not actively used. |
| 1.3.6.1.4.1.171.12.9.5.2.1.14 | ColumnswCpuAclIpRuleUserMask | read-create | current | Specifies that the rule applies to the IP protocol ID and the range of options behind the IP header. |
| 1.3.6.1.4.1.171.12.9.5.2.1.15 | ColumnswCpuAclIpRulePermit | read-create | current | This object indicates if the result of the packet examination is to 'permit' or 'deny'. The default is 'permit'. permit - Specifies that packets that match the… |
| 1.3.6.1.4.1.171.12.9.5.2.1.16 | ColumnswCpuAclIpRuleRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.5.2.1.17 | ColumnswCpuAclIpRulePort | read-create | current | Specifies that the access rule will only apply to port(s). |
| 1.3.6.1.4.1.171.12.9.5.3 | TableswCpuAclPktContRuleTable | not-accessible | current | This table contains user-defined software ACL rule information. |
| 1.3.6.1.4.1.171.12.9.5.3.1 | RowswCpuAclPktContRuleEntry | not-accessible | current | A list of information about the software ACL rule of the user-defined part of each packet. |
| 1.3.6.1.4.1.171.12.9.5.3.1.1 | ColumnswCpuAclPktContRuleProfileID | read-only | current | The ID of the software ACL mask entry, which is unique to the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.5.3.1.2 | ColumnswCpuAclPktContRuleAccessID | read-only | current | The ID of the software ACL rule entry related to swCpuAclPktContRuleProfileID. |
| 1.3.6.1.4.1.171.12.9.5.3.1.3 | ColumnswCpuAclPktContRuleOffset0to15 | read-create | current | Specifies that the rule applies to the user-defined packet. |
| 1.3.6.1.4.1.171.12.9.5.3.1.4 | ColumnswCpuAclPktContRuleOffset16to31 | read-create | current | Specifies that the rule applies to the user-defined packet. |
| 1.3.6.1.4.1.171.12.9.5.3.1.5 | ColumnswCpuAclPktContRuleOffset32to47 | read-create | current | Specifies that the rule applies to the user-defined packet. |
| 1.3.6.1.4.1.171.12.9.5.3.1.6 | ColumnswCpuAclPktContRuleOffset48to63 | read-create | current | Specifies that the rule applies to the user-defined packet. |
| 1.3.6.1.4.1.171.12.9.5.3.1.7 | ColumnswCpuAclPktContRuleOffset64to79 | read-create | current | Specifies that the rule applies to the user-defined packet. |
| 1.3.6.1.4.1.171.12.9.5.3.1.8 | ColumnswCpuAclPktContRulePermit | read-create | current | This object indicates if the result of the packet examination is to 'permit' or 'deny'. The default is 'permit'. permit - Specifies that packets that match the… |
| 1.3.6.1.4.1.171.12.9.5.3.1.9 | ColumnswCpuAclPktContRuleRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.5.3.1.10 | ColumnswCpuAclPktContRulePort | read-create | current | Specifies that the access rule will only apply to port(s). |
| 1.3.6.1.4.1.171.12.9.5.4 | TableswCpuAclIpv6RuleTable | not-accessible | current | This table contains user-defined ACL rule information. |
| 1.3.6.1.4.1.171.12.9.5.4.1 | RowswCpuAclIpv6RuleEntry | not-accessible | current | A list of information about the ACL rule of the user-defined part of each packet. |
| 1.3.6.1.4.1.171.12.9.5.4.1.1 | ColumnswCpuAclIpv6RuleProfileID | read-only | current | The ID of the ACL mask entry. This is unique in the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.5.4.1.2 | ColumnswCpuAclIpv6RuleAccessID | read-only | current | The ID of the ACL rule entry in relation to swCpuAclIpv6RuleProfileID. |
| 1.3.6.1.4.1.171.12.9.5.4.1.3 | ColumnswCpuAclIpv6RuleClass | read-create | current | Specifies that the rule applies to the IPv6 class field. |
| 1.3.6.1.4.1.171.12.9.5.4.1.4 | ColumnswCpuAclIpv6RuleFlowlabel | read-create | current | Specifies that the rule applies to the IPv6 flowlabel field. |
| 1.3.6.1.4.1.171.12.9.5.4.1.5 | ColumnswCpuAclIpv6RuleSrcIpv6Addr | read-create | current | Specifies that the rule applies to the source IPv6 address. This should be a 16 byte octet string. |
| 1.3.6.1.4.1.171.12.9.5.4.1.6 | ColumnswCpuAclIpv6RuleDstIpv6Addr | read-create | current | Specifies that the rule applies to the destination IPv6 address. This should be a 16 byte octet string. |
| 1.3.6.1.4.1.171.12.9.5.4.1.7 | ColumnswCpuAclIpv6RulePermit | read-create | current | This object indicates if the result of the examination is to 'permit' or 'deny'. The default is 'permit' (1). permit - Specifies that packets that match the ac… |
| 1.3.6.1.4.1.171.12.9.5.4.1.8 | ColumnswCpuAclIpv6RuleRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.5.4.1.9 | ColumnswCpuAclIpv6RulePort | read-create | current | Specifies that the access rule will apply only to port(s). |
| 1.3.6.1.4.1.171.12.9.6 | NodeswAclMeteringMgmt | |||
| 1.3.6.1.4.1.171.12.9.6.1 | TableswAclMeterTable | not-accessible | current | This table is used to configure the flow-based metering function. The access rule must first be created before the parameters of this function can be applied. … |
| 1.3.6.1.4.1.171.12.9.6.1.1 | RowswAclMeterEntry | not-accessible | current | This entry displays parameters and configurations set for the flow metering function. |
| 1.3.6.1.4.1.171.12.9.6.1.1.1 | ColumnswAclMeterProfileID | read-only | current | The ID of the ACL mask entry is unique in the mask list. The maximum value of this object depends on the device. |
| 1.3.6.1.4.1.171.12.9.6.1.1.2 | ColumnswAclMeterAccessID | read-only | current | The ID of the ACL rule entry as related to the swAclMeterProfileID. |
| 1.3.6.1.4.1.171.12.9.6.1.1.3 | ColumnswAclMeterRate | read-create | current | Specifies the committed bandwidth in Kbps for the flow. NOTE: 1. Specifying 0 will disable this flow meter setting. 2. Users must set the swAclMeterActionForRa… |
| 1.3.6.1.4.1.171.12.9.6.1.1.4 | ColumnswAclMeterActionForRateExceed | read-create | current | Specifies the action to take for those packets exceeding the committed rate. NOTE: Users must also set the swAclMeterRate to activate this entry. |
| 1.3.6.1.4.1.171.12.9.6.1.1.5 | ColumnswAclMeterRemarkDscp | read-create | current | Mark the packet with a specified DSCP. It can be set when swAclMeterActionForRateExceed sets remark-dscp (3). |
| 1.3.6.1.4.1.171.12.9.6.1.1.6 | ColumnswAclMeterBurstSize | read-create | current | This specifies the burst size for the single rate two color mode. The unit is Kbytes. That is to say, 1 means 1kbytes. The set value range is 0..n, the value n… |
| 1.3.6.1.4.1.171.12.9.6.1.1.7 | ColumnswAclMeterMode | read-create | current | tr-tcm: two rate three color mode; sr-tcm: single rate three color mode. |
| 1.3.6.1.4.1.171.12.9.6.1.1.8 | ColumnswAclMeterTrtcmCir | read-create | current | Specifies the 'committed information rate' of 'two rate three color mode'. The unit is Kbps. |
| 1.3.6.1.4.1.171.12.9.6.1.1.9 | ColumnswAclMeterTrtcmCbs | read-create | current | Specifies the 'committed burst size' of 'two rate three color mode'. 1. The unit is Kbytes. That is to say, 1 means 1Kbytes. 2. This parameter is an optional p… |
| 1.3.6.1.4.1.171.12.9.6.1.1.10 | ColumnswAclMeterTrtcmPir | read-create | current | Specifies the 'Peak Information Rate' of 'two rate three color mode'. The unit is Kbps. |
| 1.3.6.1.4.1.171.12.9.6.1.1.11 | ColumnswAclMeterTrtcmPbs | read-create | current | Specifies the 'peak burst size' of 'two rate three color mode'. 1. The unit is Kbytes. That is to say, 1 means 1kbytes. 2. This parameter is an optional parame… |
| 1.3.6.1.4.1.171.12.9.6.1.1.12 | ColumnswAclMeterTrtcmColorMode | read-create | current | Specifies the meter mode. The default is color-blind mode. The final color of the packet is determined by the initial color of the packet and the metering resu… |
| 1.3.6.1.4.1.171.12.9.6.1.1.13 | ColumnswAclMeterTrtcmConformState | read-create | current | Specifies the action state when packet is in 'green color'. permit: permit the packet. replace-dscp: change the DSCP value of packet. |
| 1.3.6.1.4.1.171.12.9.6.1.1.14 | ColumnswAclMeterTrtcmConformReplaceDscp | read-create | current | Specifies the DSCP value of the packet when the packet is in 'green color'. |
| 1.3.6.1.4.1.171.12.9.6.1.1.15 | ColumnswAclMeterTrtcmConformCounterState | read-create | current | Specifies the counter state when the packet is in 'green color'. 1. This is optional. The default is 'disable'. 2. The resource may be limited so that the coun… |
| 1.3.6.1.4.1.171.12.9.6.1.1.16 | ColumnswAclMeterTrtcmExceedState | read-create | current | Specifies the action state when packet is in 'yellow color'. permit: permit the packet. replace-dscp: change the DSCP value of the packet. drop: drop the packe… |
| 1.3.6.1.4.1.171.12.9.6.1.1.17 | ColumnswAclMeterTrtcmExceedReplaceDscp | read-create | current | Specifies the DSCP value of packet when packet is in 'yellow color'. |
| 1.3.6.1.4.1.171.12.9.6.1.1.18 | ColumnswAclMeterTrtcmExceedCounterState | read-create | current | Specifies the counter state when packet is in 'yellow color'. 1. This is optional. The default is 'disable'. 2. The resource may be limited so that the counter… |
| 1.3.6.1.4.1.171.12.9.6.1.1.19 | ColumnswAclMeterTrtcmViolateState | read-create | current | Specifies the action state when packet is in 'red color'. permit: permit the packet. replace-dscp: change the DSCP value of packet. drop: drop the packet. |
| 1.3.6.1.4.1.171.12.9.6.1.1.20 | ColumnswAclMeterTrtcmViolateReplaceDscp | read-create | current | Specifies the DSCP value of the packet when packet is in 'red color'. |
| 1.3.6.1.4.1.171.12.9.6.1.1.21 | ColumnswAclMeterTrtcmViolateCounterState | read-create | current | Specifies the counter state when packet is in 'red color'. 1. This is optional. The default is 'disable'. 2. The resource may be limited so that the counter ca… |
| 1.3.6.1.4.1.171.12.9.6.1.1.22 | ColumnswAclMeterSrtcmCir | read-create | current | Specifies the 'committed information rate' of 'single rate three color mode'. The unit is Kbps. |
| 1.3.6.1.4.1.171.12.9.6.1.1.23 | ColumnswAclMeterSrtcmCbs | read-create | current | Specifies the 'committed burst size' of 'single rate three color mode'. 1. The unit is Kbytes. That is to say, 1 means 1Kbytes. 2. The max set value is 16*1024. |
| 1.3.6.1.4.1.171.12.9.6.1.1.24 | ColumnswAclMeterSrtcmEbs | read-create | current | Specifies the 'Excess burst size' of 'single rate three color mode'. 1. The unit is Kbytes. That is to say, 1 means 1kbytes. 2. The max set value is 16*1024. |
| 1.3.6.1.4.1.171.12.9.6.1.1.25 | ColumnswAclMeterSrtcmColorMode | read-create | current | Specifies the meter mode. The default is color-blind mode. The final color of packet is determined by the initial color of the packet and the metering result. |
| 1.3.6.1.4.1.171.12.9.6.1.1.26 | ColumnswAclMeterSrtcmConformState | read-create | current | Specifies the action state when the packet is in 'green color'. permit: permit the packet. replace-dscp: change the DSCP value of packet. |
| 1.3.6.1.4.1.171.12.9.6.1.1.27 | ColumnswAclMeterSrtcmConformReplaceDscp | read-create | current | Specifies the DSCP value of the packet when packet is in 'green color'. |
| 1.3.6.1.4.1.171.12.9.6.1.1.28 | ColumnswAclMeterSrtcmConformCounterState | read-create | current | Specifies the counter state when the packet is in 'green color'. 1. This is optional. The default is 'disable'. 2. The resource may be limited such that counte… |
| 1.3.6.1.4.1.171.12.9.6.1.1.29 | ColumnswAclMeterSrtcmExceedState | read-create | current | Specifies the action state when the packet is in 'yellow color'. permit: permit the packet. replace-dscp: change the DSCP value of packet. drop: drop the packe… |
| 1.3.6.1.4.1.171.12.9.6.1.1.30 | ColumnswAclMeterSrtcmExceedReplaceDscp | read-create | current | Specifies the DSCP value of the packet when packet is in 'yellow color'. |
| 1.3.6.1.4.1.171.12.9.6.1.1.31 | ColumnswAclMeterSrtcmExceedCounterState | read-create | current | Specifies the counter state when the packet is in 'yellow color'. 1. This is optional. The default is 'disable'. 2. The resource may be limited such that count… |
| 1.3.6.1.4.1.171.12.9.6.1.1.32 | ColumnswAclMeterSrtcmViolateState | read-create | current | Specifies the action state when the packet is in 'red color'. permit: permit the packet. replace-dscp: change the DSCP value of packet. drop: drop the packet. |
| 1.3.6.1.4.1.171.12.9.6.1.1.33 | ColumnswAclMeterSrtcmViolateReplaceDscp | read-create | current | Specifies the DSCP value of the packet when packet is in 'red color'. |
| 1.3.6.1.4.1.171.12.9.6.1.1.34 | ColumnswAclMeterSrtcmViolateCounterState | read-create | current | Specifies the counter state when the packet is in 'red color'. 1. This is optional. The default is 'disable'. 2. The resource may be limited so that the counte… |
| 1.3.6.1.4.1.171.12.9.6.1.1.35 | ColumnswAclMeterRowStatus | read-create | current | This object indicates the status of this entry. |
| 1.3.6.1.4.1.171.12.9.6.2 | ScalarswAclMeteringNumOfEntryInUse | read-only | current | Used to display total entries of the flow metering. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Ipv6Address | OCTET STRING (SIZE (16)) | current | This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order. |
| PortList | OCTET STRING(SIZE (0..127)) |