ADTRAN-TA5K-POTS-MIB
108 objects
The is the MIB module that describes management information for the POTS. modules in a Total Access 5000 shelf
Imported Objects
| ADTRAN-GENPORT-MIB | adGenPortInfoIndex adGenPortTrapIdentifier |
| ADTRAN-GENSLOT-MIB | adGenSlotAlarmStatus adGenSlotInfoIndex |
| ADTRAN-GENTRAPINFORM-MIB | adTrapInformSeqNum |
| ADTRAN-MIB | adIdentity adMgmt adProducts |
| IF-MIB | ifIndex |
| SNMPv2-MIB | sysName |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.664.1.753 | NodeadTA5kPots | |||
| 1.3.6.1.4.1.664.2.753 | NodeadTA5kPotsmg | |||
| 1.3.6.1.4.1.664.2.753.1 | NodeadTA5kPotsProv | |||
| 1.3.6.1.4.1.664.2.753.1.1 | NodeadTA5kPotsCardProv | |||
| 1.3.6.1.4.1.664.2.753.1.1.1 | TableadTA5kPotsCardProvTable | not-accessible | current | The POTS Card-level Provisioning table. |
| 1.3.6.1.4.1.664.2.753.1.1.1.1 | RowadTA5kPotsCardProvEntry | not-accessible | current | An entry in the POTS Card-level Provisioning Table. |
| 1.3.6.1.4.1.664.2.753.1.1.1.1.1 | ColumnadTA5kPotsCardProvRestoreFactoryDefaults | read-write | current | A set command will reset the POTS card. Get has no meaning and will always return 1. |
| 1.3.6.1.4.1.664.2.753.1.1.1.1.2 | ColumnadTA5kPotsCardProvVoiceCallControl | read-write | current | The call-control protocol for all voice ports on this module - 1 = FXS Signaling (This is the same as tunneledGR303 in the syntax) 2 = ccSip 3 = MGCP |
| 1.3.6.1.4.1.664.2.753.1.1.1.1.3 | ColumnadTA5kPotsCardReboot | read-write | current | This field sets the card into boot mode 1 = Reboot |
| 1.3.6.1.4.1.664.2.753.1.1.1.1.4 | ColumnadTA5kPotsCardRemoveBatteryInOosUas | read-write | current | Remove CO battery from loop when a port is set to Out of Service - Unassigned. This typically only applies to Combo ADSL/POTS units. 1 = Yes 2 = No |
| 1.3.6.1.4.1.664.2.753.1.1.1.1.5 | ColumnadTA5kPotsCardProvLossOfTimingAlarm | read-write | current | Provisioning for Loss Of Timing Alarm which is a card level alarm. 1 = Enable 2 = Disable |
| 1.3.6.1.4.1.664.2.753.1.1.1.1.6 | ColumnadTA5kPotsCardProvAllAlarms | read-write | current | Provisioning for All Alarms (Card and Port Level). 1 = Enable 2 = Disable |
| 1.3.6.1.4.1.664.2.753.1.1.1.1.7 | ColumnadTA5kPotsCardLineTestScheduleEnable | read-write | current | Enable/Disable scheduled Fxs Line Tests. If enabled, the card will run a GR-909 line test on each applicable fxs port at the time of day set by the adTA5kPotsC… |
| 1.3.6.1.4.1.664.2.753.1.1.1.1.8 | ColumnadTA5kPotsCardLoadCoilTestScheduleEnable | read-write | current | Enable/Disable scheduled Fxs Load Coil Tests. If enabled, the card will run the load coil detection tests in addition to the GR-909 line tests at the time of d… |
| 1.3.6.1.4.1.664.2.753.1.1.1.1.9 | ColumnadTA5kPotsCardLineTestScheduleTimeString | read-write | current | Set the scheduled start time of the Line Tests in 24 Hour Format HH:MM. If adTA5kPotsCardLineTestScheduleEnable is disabled, then this oid has no effect. |
| 1.3.6.1.4.1.664.2.753.1.2 | NodeadTA5kPotsPortProv | |||
| 1.3.6.1.4.1.664.2.753.1.2.1 | TableadTA5kPotsPortProvTable | not-accessible | current | The POTS Port-level Provisioning table. |
| 1.3.6.1.4.1.664.2.753.1.2.1.1 | RowadTA5kPotsPortProvEntry | not-accessible | current | An entry in the POTS Port-level Provisioning Table. |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.1 | ColumnadTA5kPotsPortMode | read-write | current | POTS port operational Mode - 1 = Loopstart 2 = Groundstart 3 = TR08 Single Party 4 = TR08 UVG |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.2 | ColumnadTA5kPotsPortImpedance | read-write | current | POTS port 2-wire termination impedance - 1 = 600 Ohms 2,3 are no longer supported 4 = 900 Ohms + 2.16 uF 5 = z1 - 220 + (820 // 115nF) 6 = z2 - 270 + (750 // 1… |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.3 | ColumnadTA5kPotsPortTXTLPString | read-write | current | POTS Port Transmit TLP -9.0dB to +6.0dB |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.4 | ColumnadTA5kPotsPortRXTLPString | read-write | current | POTS Port Receive TLP -10.0dB to +6.0dB |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.5 | ColumnadTA5kPotsPortOnHookMsg | read-write | current | POTS Port On-Hook Messaging - 1 = Enable 2 = Disable |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.6 | ColumnadTA5kPotsPortTrunkConditioningAlarm | read-write | current | Provisioning for Enable/Disable Trunk Conditioning Alarm which is a port level alarm. 1 = Enable 2 = Disable |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.7 | ColumnadTA5kPotsPortLineShoweringAlarm | read-write | current | Provisioning for Enable/Disable Line Showering Alarm which is a port level alarm. 1 = Enable 2 = Disable |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.8 | ColumnadTA5kPotsPortAutoImpedanceMode | read-write | current | POTS Automatic Impedance Mode - 1 = Manual 2 = Automatic |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.9 | ColumnadTA5kPotsPortRingVoltage | read-write | current | POTS Ringer Voltage - 1 = 50 Vrms 2 = 60 Vrms 3 = 70 Vrms 4 = 80 Vrms 5 = 85 Vrms 6 = 90 Vrms |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.10 | ColumnadTA5kPotsPortImpedanceByLoopLength | read-write | current | POTS port 2-wire termination impedance by loop length- 1 = Other - The impedance matches one of the values defined by adTA5kPotsPortImpedance that can not be a… |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.11 | ColumnadTA5kPotsPortOverTempAlarmEnable | read-write | current | Provisioning for Enable/Disable Over Temperature Alarm which is a port level alarm. 1 = Enable 2 = Disable |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.12 | ColumnadTA5kPotsPortMwiType | read-write | current | Provisioning for the type of Message Waiting Indication for this port to use. 1 = Use Frequency Shift Keying (FSK) to indicate Message Waiting to the phone 2 =… |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.13 | ColumnadTA5kPotsPortNeonMwiCadence | read-write | current | Provisioning for the flashing cadence of Neon Message Waiting Indication for this port. 1 = Flash the Neon lamp on or off every 1000ms 2 = Flash the Neon lamp … |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.14 | ColumnadTA5kPotsPortNeonMwiVoltage | read-write | current | Provisioning for the voltage of Neon Message Waiting Indication for this port. 1 = 85 volts 2 = 90 volts 3 = 100 volts 4 = 110 volts 5 = 120 volts 6 = 130 volts |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.15 | ColumnadTA5kPotsPortVoiceCallJitterBufferDepth | read-write | current | Provisioning for the Jitter Buffer Depth used for Voice Calls in mS |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.16 | ColumnadTA5kPotsPortFaxModemCallJitterBufferDepth | read-write | current | Provisioning for the Jitter Buffer Depth used for Fax Modem Calls in mS |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.17 | ColumnadTA5kPotsPortCircuitIdentifier | read-write | current | The circuit identifier string for the fxs port. |
| 1.3.6.1.4.1.664.2.753.1.2.1.1.18 | ColumnadTA5kPotsPulseDigitDetectionEnable | read-write | current | This entry is used to enable or disable the pulse dial digit detection for this port. This entry only applies to fxs ports that are connected to a VoIP service… |
| 1.3.6.1.4.1.664.2.753.2 | NodeadTA5kPotsStat | |||
| 1.3.6.1.4.1.664.2.753.2.1 | NodeadTA5kPotsCardStat | |||
| 1.3.6.1.4.1.664.2.753.2.1.1 | TableadTA5kPotsCardStatTable | not-accessible | current | The POTS Card-level Status table. |
| 1.3.6.1.4.1.664.2.753.2.1.1.1 | RowadTA5kPotsCardStatEntry | not-accessible | current | An entry in the POTS Card-level Status Table. |
| 1.3.6.1.4.1.664.2.753.2.1.1.1.1 | ColumnadTA5kPotsCardSelfTestFPGATest | read-only | current | This variable indicates the Self-test FPGA Test Status of the module. 1 = FAILED 2 = PASSED |
| 1.3.6.1.4.1.664.2.753.2.1.1.1.2 | ColumnadTA5kPotsCardSelfTestFlashTest | read-only | current | This variable indicates the Self-test FPGA Flash Test Status of the module. 1 = FAILED 2 = PASSED |
| 1.3.6.1.4.1.664.2.753.2.1.1.1.3 | ColumnadTA5kPotsCardSelfTestLasVegas1Prog | read-only | current | This variable indicates the Self-test Las Vegas #1 Programming Status of the module. 1 = FAILED 2 = PASSED |
| 1.3.6.1.4.1.664.2.753.2.1.1.1.4 | ColumnadTA5kPotsCardSelfTestLasVegas2Prog | read-only | current | This variable indicates the Self-test Las Vegas #2 Programming Status of the module. 1 = FAILED 2 = PASSED |
| 1.3.6.1.4.1.664.2.753.2.1.1.1.5 | ColumnadTA5kPotsCardSelfTestVineticCodecAProg | read-only | current | This variable indicates the Self-test Vinetic Codec A Programming Status of the module. 1 = FAILED 2 = PASSED |
| 1.3.6.1.4.1.664.2.753.2.1.1.1.6 | ColumnadTA5kPotsCardSelfTestVineticCodecBProg | read-only | current | This variable indicates the Self-test Vinetic Codec B Programming Status of the module. 1 = FAILED 2 = PASSED |
| 1.3.6.1.4.1.664.2.753.2.1.1.1.7 | ColumnadTA5kPotsCardSelfTestVineticCodecCProg | read-only | current | This variable indicates the Self-test Vinetic Codec C Programming Status of the module. 1 = FAILED 2 = PASSED |
| 1.3.6.1.4.1.664.2.753.2.1.1.1.8 | ColumnadTA5kPotsCardSelfTestVineticCodecDProg | read-only | current | This variable indicates the Self-test Vinetic Codec D Programming Status of the module. 1 = FAILED 2 = PASSED |
| 1.3.6.1.4.1.664.2.753.2.1.1.1.9 | ColumnadTA5kPotsCardSelfTestVineticCodecEProg | read-only | current | This variable indicates the Self-test Vinetic Codec E Programming Status of the module. 1 = FAILED 2 = PASSED |
| 1.3.6.1.4.1.664.2.753.2.1.1.1.10 | ColumnadTA5kPotsCardSelfTestVineticCodecFProg | read-only | current | This variable indicates the Self-test Vinetic Codec F Programming Status of the module. 1 = FAILED 2 = PASSED |
| 1.3.6.1.4.1.664.2.753.2.1.1.1.11 | ColumnadTA5kPotsCardSelfTestLasVegas3Prog | read-only | current | This variable indicates the Self-test Las Vegas #3 Programming Status of the module. 1 = FAILED 2 = PASSED |
| 1.3.6.1.4.1.664.2.753.2.2 | NodeadTA5kPotsPortStat | |||
| 1.3.6.1.4.1.664.2.753.2.2.1 | TableadTA5kPotsPortStatTable | not-accessible | current | The POTS Port-level Status table. |
| 1.3.6.1.4.1.664.2.753.2.2.1.1 | RowadTA5kPotsPortStatEntry | not-accessible | current | An entry in the POTS Port-level Status Table. |
| 1.3.6.1.4.1.664.2.753.2.2.1.1.1 | ColumnadTA5kPotsPortStatLineMode | read-only | current | This item indicates which mode the port is currently operating in. 1 = Loop Start 2 = Ground Start |
| 1.3.6.1.4.1.664.2.753.2.2.1.1.2 | ColumnadTA5kPotsPortStatLineActive | read-only | current | This item indicates whether the port is currently active or not. 1 = Active 2 = Not Active |
| 1.3.6.1.4.1.664.2.753.2.2.1.1.3 | ColumnadTA5kPotsPortStatLineCompression | read-only | current | This item indicates which type of compression is being used. 1 = G.711 2 = G.726 |
| 1.3.6.1.4.1.664.2.753.2.2.1.1.4 | ColumnadTA5kPotsPortStatLoopFeed | read-only | current | This item indicates the loop feed status of the port. 1 = Loop Current Feed 2 = Reverse Loop Current Feed 3 = OSI 4 = Tip Ground 5 = Ringing 6 = Power Down |
| 1.3.6.1.4.1.664.2.753.2.2.1.1.5 | ColumnadTA5kPotsPortStatLoopState | read-only | current | This item indicates the loop state of the port. 1 = Loop Open 2 = Loop Closed 3 = Ring Ground |
| 1.3.6.1.4.1.664.2.753.2.2.1.1.6 | ColumnadTA5kPotsPortStatTestActive | read-only | current | This item indicates whether a test is active on the port or not. 1 = Active 2 = Not Active |
| 1.3.6.1.4.1.664.2.753.2.2.1.1.7 | ColumnadTA5kPotsPortStatServiceState | read-only | current | POTS port service state- 1 = In Service 2 = Out Of Service - Unassigned 3 = Out Of Service - Maintenance |
| 1.3.6.1.4.1.664.2.753.2.2.1.1.8 | ColumnadTA5kPotsPortMwiStatus | read-only | current | POTS MWI Status - 1 = Status Unknown 2 = Indicator OFF 3 = Indicator ON 4 = Indicator OFF (forced) 5 = Indicator ON (forced) Note: unknown will always be retur… |
| 1.3.6.1.4.1.664.2.753.2.3 | NodeadTA5kPotsStatistics | |||
| 1.3.6.1.4.1.664.2.753.2.3.1 | NodeadTA5kPotscardStatistics | |||
| 1.3.6.1.4.1.664.2.753.2.3.1.1 | TableadTA5kPotscardStatisticsTable | not-accessible | current | The POTS card-level Statistics table. |
| 1.3.6.1.4.1.664.2.753.2.3.1.1.1 | RowadTA5kPotscardStatisticsEntry | not-accessible | current | An entry in the POTS card-level Statistics Table. |
| 1.3.6.1.4.1.664.2.753.2.3.1.1.1.1 | ColumnadTA5kPotsCardRXEthernetPkts | read-only | current | This will give the number of Received ethernet packets |
| 1.3.6.1.4.1.664.2.753.2.3.1.1.1.2 | ColumnadTA5kPotsCardTXEthernetPkts | read-only | current | This will give the number of transmitted ethernet packets |
| 1.3.6.1.4.1.664.2.753.2.3.1.1.1.3 | ColumnadTA5kPotsCardVoiceGatewayTimeouts | read-only | current | This will give the voice gateway timeouts |
| 1.3.6.1.4.1.664.2.753.2.3.1.1.1.4 | ColumnadTA5kPotsCardClearStatistics | read-write | current | This will clear all the card level statistics when set to 1. A get will always return a 1. 1 = Clear |
| 1.3.6.1.4.1.664.2.753.2.3.1.1.1.5 | ColumnadTA5kPotsPortClearStatistics | read-write | current | This will clear all Port level statistics when set to 1. A get will always return a 1. 1 = Clear |
| 1.3.6.1.4.1.664.2.753.2.3.2 | NodeadTA5kPotsPortStatistics | |||
| 1.3.6.1.4.1.664.2.753.2.3.2.1 | TableadTA5kPotsPortStatisticsTable | not-accessible | current | The POTS port-level Statistics table. |
| 1.3.6.1.4.1.664.2.753.2.3.2.1.1 | RowadTA5kPotsPortStatisticsEntry | not-accessible | current | An entry in the POTS port-level Statistics Table. |
| 1.3.6.1.4.1.664.2.753.2.3.2.1.1.1 | ColumnadTA5kPotsPortRXVoicePkts | read-only | current | This will give the number of Received Voice packets |
| 1.3.6.1.4.1.664.2.753.2.3.2.1.1.2 | ColumnadTA5kPotsPortTXVoicePkts | read-only | current | This will give the number of transmitted Voice packets |
| 1.3.6.1.4.1.664.2.753.2.3.2.1.1.3 | ColumnadTA5kPotsPortRXSignalPkts | read-only | current | This will give the number of Received signal packets |
| 1.3.6.1.4.1.664.2.753.2.3.2.1.1.4 | ColumnadTA5kPotsPortTXSignalPkts | read-only | current | This will give the number of transmitted signal packets |
| 1.3.6.1.4.1.664.2.753.3 | NodeadTA5kPotsTest | |||
| 1.3.6.1.4.1.664.2.753.3.1 | NodeadTA5kPotsCardTest | |||
| 1.3.6.1.4.1.664.2.753.3.1.1 | TableadTA5kPotsCardTestTable | not-accessible | current | The POTS Card-level Test table. |
| 1.3.6.1.4.1.664.2.753.3.1.1.1 | RowadTA5kPotsCardTestEntry | not-accessible | current | An entry in the POTS Card-level Test Table. |
| 1.3.6.1.4.1.664.2.753.3.1.1.1.1 | ColumnadTA5kPotsCardTestLpbkPotsLine | read-write | current | This item enables/disables the POTS line loopback toward the network. 1 = Enable 2 = Disable |
| 1.3.6.1.4.1.664.2.753.3.1.1.1.2 | ColumnadTA5kPotsCardTestLpbkPotsPayload | read-write | current | This item enables/disables the POTS payload loopback toward the network. 1 = Enable 2 = Disable |
| 1.3.6.1.4.1.664.2.753.3.2 | NodeadTA5kPotsLineTest | |||
| 1.3.6.1.4.1.664.2.753.3.2.1 | TableadTA5kPotsLineTestTable | not-accessible | current | The POTS Line-level Test table. |
| 1.3.6.1.4.1.664.2.753.3.2.1.1 | RowadTA5kPotsLineTestEntry | not-accessible | current | An entry in the POTS Line-level Test Table. |
| 1.3.6.1.4.1.664.2.753.3.2.1.1.1 | ColumnadTA5kPotsLineTest1004HzTone | read-write | current | This item controls the generation of a 1004 Hz test tone from the POTS interface. 1 = To Loop 2 = To Network 3 = Disable |
| 1.3.6.1.4.1.664.2.753.3.2.1.1.2 | ColumnadTA5kPotsLineTestRingCadence | read-write | current | This item enables/disables the ring cadence test on the POTS interface. 1 = Enable 2 = Disable |
| 1.3.6.1.4.1.664.2.753.3.2.1.1.3 | ColumnadTA5kPotsLineTestLoopState | read-write | current | This item controls the loop state test on the POTS interface. 1 = Disable 2 = Active High 3 = Active Low 4 = Reverse Active High 5 = Reverse Active Low 6 = Pow… |
| 1.3.6.1.4.1.664.2.753.3.2.1.1.4 | ColumnadTA5kPotsLineClearTest | read-write | current | This will clear all Port Line Tests. The get will always return 1. 1 = Clear |
| 1.3.6.1.4.1.664.2.753.3.2.1.1.5 | ColumnadTA5kPotsLineTestWarbleTone | read-write | current | This will enable or disable a warble tone as defined by the oids adTA5kPotsLineTestWarbleToneFreq1, adTA5kPotsLineTestWarbleToneFreq2, and adTA5kPotsLineTestWa… |
| 1.3.6.1.4.1.664.2.753.3.2.1.1.6 | ColumnadTA5kPotsLineTestWarbleToneFreq1 | read-write | current | The first alternating frequency used in the warble tone. |
| 1.3.6.1.4.1.664.2.753.3.2.1.1.7 | ColumnadTA5kPotsLineTestWarbleToneFreq2 | read-write | current | The second alternating frequency used in the warble tone. |
| 1.3.6.1.4.1.664.2.753.3.2.1.1.8 | ColumnadTA5kPotsLineTestWarbleToneCadence | read-write | current | The amount of time in ms that one frequency in the warble tone is played before alternating to the the other frequency. |
| 1.3.6.1.4.1.664.2.753.3.2.1.1.9 | ColumnadTA5kPotsPortForceMwiOffEvent | read-write | current | A set command will force the Message Waiting Indicator for the port to turn OFF. Get has no meaning and will always return indicatorOff(1). This provides a mea… |
| 1.3.6.1.4.1.664.2.753.3.2.1.1.10 | ColumnadTA5kPotsPortForceMwiOnEvent | read-write | current | A set command will force the Message Waiting Indicator for the port to turn ON. Get has no meaning and will always return indicatorOn(1). This provides a means… |
| 1.3.6.1.4.1.664.2.753.4 | NodeadTA5kPotsAlarm | |||
| 1.3.6.1.4.1.664.2.753.4.0 | NodeadTA5kPotsAlarmEvents | |||
| 1.3.6.1.4.1.664.2.753.4.0.2 | NotificationadTa5kPotsTrunkConditioningTrapClear | current | Indicates Trunk Conditioning Alarm Clear. | |
| 1.3.6.1.4.1.664.2.753.4.0.3 | NotificationadTa5kPotsTrunkConditioningTrapActive | current | Indicates Trunk Conditioning Alarm Active. | |
| 1.3.6.1.4.1.664.2.753.4.0.4 | NotificationadTa5kPotsLineShoweringTrapClear | current | Indicates Line Showering Alarm Clear. | |
| 1.3.6.1.4.1.664.2.753.4.0.5 | NotificationadTa5kPotsLineShoweringTrapActive | current | Indicates Line Showering Alarm Active. | |
| 1.3.6.1.4.1.664.2.753.4.0.6 | NotificationadTa5kPotsBackplaneTimingTrapClear | current | Indicates Backplane Timing Alarm Clear. | |
| 1.3.6.1.4.1.664.2.753.4.0.7 | NotificationadTa5kPotsBackplaneTimingTrapActive | current | Indicates Backplane Timing Alarm Active. | |
| 1.3.6.1.4.1.664.2.753.4.0.8 | NotificationadTa5kPotsOverTempTrapClear | current | Indicates Over Temperature Alarm Clear if the POTS chipset has not indicated, in the last five minutes, that the temperature has risen to a level such that the… | |
| 1.3.6.1.4.1.664.2.753.4.0.9 | NotificationadTa5kPotsOverTempTrapActive | current | Indicates Over Temperature Alarm Active if the POTS chipset has indicated, at least once in the last five minutes, that the temperature for this port has risen… | |
| 1.3.6.1.4.1.664.6.753 | IdentityadTA5kPotsID | The is the MIB module that describes management information for the POTS. modules in a Total Access 5000 shelf |