MIB Viewer

AGENT-GENERAL-MIB

288 objects
The structure of general management information for enterprise.
Imported Objects
DLINK-ID-REC-MIBAgentNotifyLevel dlink-common-mgmt
INET-ADDRESS-MIBInetAddress InetAddressType
Q-BRIDGE-MIBVlanId
RFC1213-MIBDisplayString
SNMPv2-SMIInteger32 IpAddress MODULE-IDENTITY OBJECT-TYPE
SNMPv2-TCMacAddress RowStatus TruthValue
OIDNameAccessStatusDescription
1.3.6.1.4.1.171.12.1IdentityagentGeneralMgmtThe structure of general management information for enterprise.
1.3.6.1.4.1.171.12.1.1NodeagentBasicInfo
1.3.6.1.4.1.171.12.1.1.1ScalaragentMgmtProtocolCapabilityread-onlycurrentThe network management protocol(s) supported by this agent.
1.3.6.1.4.1.171.12.1.1.2TableagentMibCapabilityTablenot-accessiblecurrentA list of MIB capability entries supported by this agent.
1.3.6.1.4.1.171.12.1.1.2.1RowagentMibCapabilityEntrynot-accessiblecurrentA MIB capability entry containing objects that describe a particular MIB supported by this agent.
1.3.6.1.4.1.171.12.1.1.2.1.1ColumnagentMibCapabilityIndexread-onlycurrentA list of Agent MIB Capability Description entries.
1.3.6.1.4.1.171.12.1.1.2.1.2ColumnagentMibCapabilityDescrread-onlycurrentThe name of the MIB supported by the agent.
1.3.6.1.4.1.171.12.1.1.2.1.3ColumnagentMibCapabilityVersionread-onlycurrentThe version of the MIB specified in this entry.
1.3.6.1.4.1.171.12.1.1.2.1.4ColumnagentMibCapabilityTyperead-onlycurrentThe type of MIB specified in this entry.
1.3.6.1.4.1.171.12.1.1.3ScalaragentStatusConsoleInUseread-onlycurrentThis indicates whether the console is currently in use.
1.3.6.1.4.1.171.12.1.1.4ScalaragentStatusSaveCfgread-onlycurrentThis indicates the status of the device configuration. other (1) - This entry is currently in use but the conditions under which it will remain so are determin…
1.3.6.1.4.1.171.12.1.1.5ScalaragentStatusFileTransferread-onlycurrentThe status of the firmware download control. If the value is stated as 'other', the firmware has not been updated since the device was started.
1.3.6.1.4.1.171.12.1.1.6NodeagentCPUutilization
1.3.6.1.4.1.171.12.1.1.6.1ScalaragentCPUutilizationIn5secread-onlycurrentThe time scale is set at 5 second intervals. The value will be between 0% (idle) and 100% (very busy).
1.3.6.1.4.1.171.12.1.1.6.2ScalaragentCPUutilizationIn1minread-onlycurrentThe time scale is set at 1 minute intervals. The value will be between 0% (idle) and 100% (very busy).
1.3.6.1.4.1.171.12.1.1.6.3ScalaragentCPUutilizationIn5minread-onlycurrentThe time scale is set at 5 minute intervals. The value will be between 0% (idle) and 100% (very busy).
1.3.6.1.4.1.171.12.1.1.7ScalaragentDualImageStatusread-onlycurrentThe dual image status.
1.3.6.1.4.1.171.12.1.1.8TableagentPORTutilizationTablenot-accessiblecurrentThis table specifies the current utilization of a specified port.
1.3.6.1.4.1.171.12.1.1.8.1RowagentPORTutilizationEntrynot-accessiblecurrentA list of information regarding the port utilization function.
1.3.6.1.4.1.171.12.1.1.8.1.1ColumnagentPORTutilizationProtIndexread-onlycurrentThis object indicates the module's port number.
1.3.6.1.4.1.171.12.1.1.8.1.2ColumnagentPORTutilizationTXread-onlycurrentThe current rate of transmitted frames on the specified port.
1.3.6.1.4.1.171.12.1.1.8.1.3ColumnagentPORTutilizationRXread-onlycurrentThe current rate of received frames on the specified port.
1.3.6.1.4.1.171.12.1.1.8.1.4ColumnagentPORTutilizationUtilread-onlycurrentThe current percentages regarding port statistics.
1.3.6.1.4.1.171.12.1.1.9TableagentDRAMutilizationTablenot-accessiblecurrentInformation about DRAM memory.
1.3.6.1.4.1.171.12.1.1.9.1RowagentDRAMutilizationEntrynot-accessiblecurrentA list of information about DRAM memory.
1.3.6.1.4.1.171.12.1.1.9.1.1ColumnagentDRAMutilizationUnitIDread-onlycurrentSpecifies the unit ID. If the ID equals zero, it means the current device.
1.3.6.1.4.1.171.12.1.1.9.1.2ColumnagentDRAMutilizationTotalDRAMread-onlycurrentThe size of total DRAM memory.
1.3.6.1.4.1.171.12.1.1.9.1.3ColumnagentDRAMutilizationUsedDRAMread-onlycurrentThe size of used DRAM memory.
1.3.6.1.4.1.171.12.1.1.9.1.4ColumnagentDRAMutilizationread-onlycurrentThe percentage of used DRAM memory of the total DRAM memory available. The value will be between 0% (idle) and 100% (very busy).
1.3.6.1.4.1.171.12.1.1.10TableagentFLASHutilizationTablenot-accessiblecurrentInformation about the flash memory.
1.3.6.1.4.1.171.12.1.1.10.1RowagentFLASHutilizationEntrynot-accessiblecurrentInformation about the flash memory.
1.3.6.1.4.1.171.12.1.1.10.1.1ColumnagentFLASHutilizationUnitIDread-onlycurrentSpecifies the unit ID. If the ID equals zero, it means the current device.
1.3.6.1.4.1.171.12.1.1.10.1.2ColumnagentFLASHutilizationTotalFLASHread-onlycurrentThe total size of flash memory.
1.3.6.1.4.1.171.12.1.1.10.1.3ColumnagentFLASHutilizationUsedFLASHread-onlycurrentThe size of the used flash memory.
1.3.6.1.4.1.171.12.1.1.10.1.4ColumnagentFLASHutilizationread-onlycurrentThe percentage of used flash memory in total flash memory. The value will be between 0% (idle) and 100% (very busy).
1.3.6.1.4.1.171.12.1.1.11ScalaragentStatusResetread-onlycurrentThis indicates the status of 'agentReset'.
1.3.6.1.4.1.171.12.1.1.12ScalaragentSerialNumberread-onlycurrentA text string containing the serial number of this device.
1.3.6.1.4.1.171.12.1.1.13ScalaragentFirmwareTyperead-onlycurrentA text string containing the firmware type.
1.3.6.1.4.1.171.12.1.2NodeagentBasicConfig
1.3.6.1.4.1.171.12.1.2.1TableagentBscSwFileTablenot-accessiblecurrentA list of MIB Basic Config entry support files updated by this agent.
1.3.6.1.4.1.171.12.1.2.1.1RowagentBscSwFileEntrynot-accessiblecurrentA basic configuration entry containing the objects that describe a particular MIB supported by this agent.
1.3.6.1.4.1.171.12.1.2.1.1.1ColumnagentBscSwFileIndexread-onlycurrentThe table index for the file entry
1.3.6.1.4.1.171.12.1.2.1.1.2ColumnagentBscSwFileDscrread-writecurrentThe description of the software file purpose in this entry. Note: For systems that do not support a change to this object, setting a value for this object will…
1.3.6.1.4.1.171.12.1.2.1.1.3ColumnagentBscSwFileAddrread-writecurrentThe IP address where the file that needs to be downloaded is located, or the IP address where the file will be uploaded to.
1.3.6.1.4.1.171.12.1.2.1.1.4ColumnagentBscSwFileTransferTyperead-writecurrentThe channel through which the file will be downloaded or uploaded. Note: For systems that do not support all channels, setting a value to the unsupported chann…
1.3.6.1.4.1.171.12.1.2.1.1.5ColumnagentBscSwFileread-writecurrentThe name of the file to be downloaded from, or uploaded to, the TFTP server.
1.3.6.1.4.1.171.12.1.2.1.1.6ColumnagentBscSwFileLocateIdread-writecurrentThis object describes the type of file. runtime-code (1), log-file (2), cfg-file (3) Note: For systems that do not support changes to this object, setting a va…
1.3.6.1.4.1.171.12.1.2.1.1.7ColumnagentBscSwFileLoadTyperead-writecurrentThis object provides the user with a choice of uploading or downloading the selected file. Note: For systems that do not support a change to this object, setti…
1.3.6.1.4.1.171.12.1.2.1.1.8ColumnagentBscSwFileCtrlread-writecurrentThis object gives the user the option of downloading runtime software. This setting will take effect when the system restarts. See Note (1) below Note: For sys…
1.3.6.1.4.1.171.12.1.2.1.1.9ColumnagentBscSwFileBIncrementread-writecurrentThis object indicates whether the previous configuration will remain valid or not after downloading the configuration file. True: Keep valid False: Erase.
1.3.6.1.4.1.171.12.1.2.1.1.10ColumnagentBscSwFileCtrlIDread-writecurrentThe section ID of the firmware image or configuration file. A value of 0 indicates the boot-up firmware image or configuration file.
1.3.6.1.4.1.171.12.1.2.1.1.11ColumnagentBscSwFileCtrlUnitIDread-writecurrentSpecifies which unit of the switch stack the firmware image will be downloaded from. One or more units can be set in this list. Each bit from the left to the r…
1.3.6.1.4.1.171.12.1.2.1.1.12ColumnagentBscSwFileIPv6Addrread-writecurrentThe IPv6 address where the file will be downloaded from or uploaded to.
1.3.6.1.4.1.171.12.1.2.1.1.13ColumnagentBscSwFileBootUpImageread-writecurrentThe result of the download will depend on whether the boot_up option is specified. Case 1: In the case where the master unit provides the file system and the s…
1.3.6.1.4.1.171.12.1.2.1.1.14ColumnagentBscSwFileForceAgreeread-writecurrentWhen the force_agree option is specified, the reboot command will be executed immediately, without any further confirmation from the user. True: force_agree op…
1.3.6.1.4.1.171.12.1.2.1.1.15ColumnagentBscSwFileInterfaceNameread-writecurrentThis node is used to specify the interface name when the agentBscSwFileIPv6Addr is the link local address.
1.3.6.1.4.1.171.12.1.2.1.1.16ColumnagentBscSwFileServerDomainNameread-writecurrentThis object indicates the domain name of the TFTP server.
1.3.6.1.4.1.171.12.1.2.2ScalaragentFileTransferread-writeobsoleteThis object will execute the download or upload action. If start (2) is chosen, it will begin to download/upload and no reset will follow. If start-and-reset (…
1.3.6.1.4.1.171.12.1.2.3ScalaragentSystemResetread-writedeprecatedThis object indicates the agent system reset state. Setting this object to no-reset (4) has no effect. Setting this object to cold-start (2) or warm-start (3) …
1.3.6.1.4.1.171.12.1.2.4ScalaragentRs232PortConfigread-writecurrentThis object indicates the RS-232C mode once the device has restarted.
1.3.6.1.4.1.171.12.1.2.5ScalaragentOutOfBandBaudRateConfigread-writeobsoleteThis object allows the user to specify an out-of-band baud rate, which will take effect upon system restart. Note: Because these functions will be limited by t…
1.3.6.1.4.1.171.12.1.2.6ScalaragentSaveCfgread-writecurrentThis object indicates the type of save command to be executed, when saving to NV-RAM. other (1) - None of the following. cfg-id1 (2) - Save configuration ID1. …
1.3.6.1.4.1.171.12.1.2.7TableswMultiImageInfoTablenot-accessiblecurrent
1.3.6.1.4.1.171.12.1.2.7.1RowswMultiImageInfoEntrynot-accessiblecurrentA list of information about multiple image management.
1.3.6.1.4.1.171.12.1.2.7.1.1ColumnswMultiImageInfoIDread-onlycurrentThe stacking section ID of the firmware image. The stacking section ID = 256 * Unit ID + Image File ID.
1.3.6.1.4.1.171.12.1.2.7.1.2ColumnswMultiImageVersionread-onlycurrentThe recorded downloaded firmware version.
1.3.6.1.4.1.171.12.1.2.7.1.3ColumnswMultiImageSizeread-onlycurrentThe recorded downloaded firmware size.
1.3.6.1.4.1.171.12.1.2.7.1.4ColumnswMultiImageUpdateTimeread-onlycurrentThe recorded firmware update time.
1.3.6.1.4.1.171.12.1.2.7.1.5ColumnswMultiImageFromread-onlycurrentThe recorded IP address of the TFTP server
1.3.6.1.4.1.171.12.1.2.7.1.6ColumnswMultiImageSendUserread-onlycurrentThe record of the user who downloaded the firmware.
1.3.6.1.4.1.171.12.1.2.7.1.7ColumnswMultiImageFileNameread-onlycurrentWhen the system is set to boot from SD card, this object will display the recorded path name of the boot firmware file.
1.3.6.1.4.1.171.12.1.2.8NodeagentMultiCfgMgmt
1.3.6.1.4.1.171.12.1.2.8.1TableswMultiCfgInfoTablenot-accessiblecurrent
1.3.6.1.4.1.171.12.1.2.8.1.1RowswMultiCfgInfoEntrynot-accessiblecurrentA list of information about multiple configuration files.
1.3.6.1.4.1.171.12.1.2.8.1.1.1ColumnswMultiCfgInfoIDread-onlycurrentThe section ID of the configuration files.
1.3.6.1.4.1.171.12.1.2.8.1.1.2ColumnswMultiCfgVersionread-onlycurrentThe recorded downloaded configuration version.
1.3.6.1.4.1.171.12.1.2.8.1.1.3ColumnswMultiCfgSizeread-onlycurrentThe recorded downloaded configuration size (in bytes).
1.3.6.1.4.1.171.12.1.2.8.1.1.4ColumnswMultiCFgUpdateTimeread-onlycurrentThe recorded configuration update time displayed in string format, i.e. yyyy/mon/dd hh:mm:ss.
1.3.6.1.4.1.171.12.1.2.8.1.1.5ColumnswMultiCfgFromread-onlycurrentThe recorded IP address of the TFTP server.
1.3.6.1.4.1.171.12.1.2.8.1.1.6ColumnswMultiCfgSendUserread-onlycurrentThe record of the user who downloaded the configuration file
1.3.6.1.4.1.171.12.1.2.8.1.1.7ColumnswMultiCfgFileNameread-onlycurrentWhen the system is set to boot from SD card, this object displays the recorded path name of the boot configuration file.
1.3.6.1.4.1.171.12.1.2.8.2ScalarswMultiCfgCurrentUsedread-onlycurrentThe indicated configuration file ID of the system currently in use.
1.3.6.1.4.1.171.12.1.2.8.3ScalarswMultiCfgBootUpread-onlycurrentThis object indicates the configuration file ID which will take effect upon the next reboot.
1.3.6.1.4.1.171.12.1.2.8.4TableswMultiCfgCtrlTablenot-accessiblecurrent
1.3.6.1.4.1.171.12.1.2.8.4.1RowswMultiCfgCtrlEntrynot-accessiblecurrentA list of information about multiple configuration management.
1.3.6.1.4.1.171.12.1.2.8.4.1.1ColumnswMultiCfgCtrlIDread-onlycurrentThe section ID of the configuration file.
1.3.6.1.4.1.171.12.1.2.8.4.1.2ColumnswMultiCfgActionread-writecurrentsave: Save configuration to active configuration ID when the parameter is omitted. active: Set any valid configuration as the active configuration. delete: Rem…
1.3.6.1.4.1.171.12.1.2.9NodesystemSeverityControlMgmt
1.3.6.1.4.1.171.12.1.2.9.1ScalarsystemSeverityTrapControlread-writecurrentIndicates the level of trap severity control. The system has a severity level control and each trap should have a severity control set. When trap events occur …
1.3.6.1.4.1.171.12.1.2.9.2ScalarsystemSeverityLogControlread-writecurrentIndicates the level of trap severity control. The system has a severity level control and each trap should have a severity control set. When trap events occur …
1.3.6.1.4.1.171.12.1.2.10NodeagentTrustedHostMgmt
1.3.6.1.4.1.171.12.1.2.10.1TableagentTrustedHostTablenot-accessiblecurrentThis table contains the trusted host information.
1.3.6.1.4.1.171.12.1.2.10.1.1RowagentTrustedHostEntrynot-accessiblecurrentA list of information about the trusted hosts.
1.3.6.1.4.1.171.12.1.2.10.1.1.1ColumnagentTrustedHostIndexread-onlycurrentThe index of the trusted host entry.
1.3.6.1.4.1.171.12.1.2.10.1.1.2ColumnagentTrustedHostIPAddressread-createcurrentSpecifies the IP address of the trusted host.
1.3.6.1.4.1.171.12.1.2.10.1.1.3ColumnagentTrustedHostRowStatusread-createcurrentIndicates the status of this entry. When creating a trusted host entry, the IP address should also be set.
1.3.6.1.4.1.171.12.1.2.10.1.1.4ColumnagentTrustedHostIPSubnetMaskread-createcurrentSpecifies the IP subnet mask of the trusted host.
1.3.6.1.4.1.171.12.1.2.10.1.1.5ColumnagentTrustedHostForSNMPread-createcurrentSpecifies the trusted host for SNMP.
1.3.6.1.4.1.171.12.1.2.10.1.1.6ColumnagentTrustedHostForTELNETread-createcurrentSpecifies the trusted host for Telnet.
1.3.6.1.4.1.171.12.1.2.10.1.1.7ColumnagentTrustedHostForSSHread-createcurrentSpecifies the trusted host for SSH.
1.3.6.1.4.1.171.12.1.2.10.1.1.8ColumnagentTrustedHostForHTTPread-createcurrentSpecifies the trusted host for HTTP.
1.3.6.1.4.1.171.12.1.2.10.1.1.9ColumnagentTrustedHostForHTTPSread-createcurrentSpecifies the trusted host for HTTPS.
1.3.6.1.4.1.171.12.1.2.10.1.1.10ColumnagentTrustedHostForPINGread-createcurrentSpecifies the trusted host for PING.
1.3.6.1.4.1.171.12.1.2.10.1.1.11ColumnagentTrustedHostAddrTyperead-createcurrentThe type of trusted host address as specified by the 'agentTrustedHostAddr' object.
1.3.6.1.4.1.171.12.1.2.10.1.1.12ColumnagentTrustedHostAddrread-createcurrentSpecifies the IP address of the trusted host.
1.3.6.1.4.1.171.12.1.2.10.1.1.13ColumnagentTrustedHostIPv6PrefixLenread-createcurrentSpecifies the IPv6 prefix length of the IPv6 trusted host.
1.3.6.1.4.1.171.12.1.2.10.2ScalaragentTrustedHostDelAllStateread-writecurrentUsed to delete all trusted host entries.
1.3.6.1.4.1.171.12.1.2.11NodeagentFDBMgmt
1.3.6.1.4.1.171.12.1.2.11.1ScalaragentFDBClearAllStateread-writecurrentUsed to clear all FDB entries.
1.3.6.1.4.1.171.12.1.2.11.2TableagentFDBClearByPortTablenot-accessiblecurrentUsed to clear FDB entries by port.
1.3.6.1.4.1.171.12.1.2.11.2.1RowagentFDBClearByPortEntrynot-accessiblecurrentThis is an entry of the agentFDBClearByPortTable.
1.3.6.1.4.1.171.12.1.2.11.2.1.1ColumnagentFDBClearPortIndexnot-accessiblecurrentThis object indicates the port number.
1.3.6.1.4.1.171.12.1.2.11.2.1.2ColumnagentFDBClearByPortActionread-writecurrentThis object indicates whether to clear FDB or not.
1.3.6.1.4.1.171.12.1.2.11.3TableagentFDBClearByVlanTablenot-accessiblecurrentUsed to clear FDB entries by port.
1.3.6.1.4.1.171.12.1.2.11.3.1RowagentFDBClearByVlanEntrynot-accessiblecurrentThis is an entry of agentFDBClearByPortTable.
1.3.6.1.4.1.171.12.1.2.11.3.1.1ColumnagentFDBClearVidnot-accessiblecurrentThis object indicates the VLAN-ID.
1.3.6.1.4.1.171.12.1.2.11.3.1.2ColumnagentFDBClearByVlanActionread-writecurrentThis object indicates whether to clear the FDB or not.
1.3.6.1.4.1.171.12.1.2.11.4TableagentFDBSecurityTablenot-accessiblecurrentUsed to display the FDB entries that have been created by the security module.
1.3.6.1.4.1.171.12.1.2.11.4.1RowagentFDBSecurityEntrynot-accessiblecurrentThis is an entry of agentFDBSecurityTable.
1.3.6.1.4.1.171.12.1.2.11.4.1.1ColumnagentFDBVidnot-accessiblecurrentThis object indicates the VLAN-ID.
1.3.6.1.4.1.171.12.1.2.11.4.1.2ColumnagentFDBMacAddressnot-accessiblecurrentThis object indicates the MAC address.
1.3.6.1.4.1.171.12.1.2.11.4.1.3ColumnagentFDBPortread-onlycurrentThis object indicates the port number.
1.3.6.1.4.1.171.12.1.2.11.4.1.4ColumnagentFDBTyperead-onlycurrentThis object indicates the MAC address type.
1.3.6.1.4.1.171.12.1.2.11.4.1.5ColumnagentFDBStatusread-onlycurrentThis object indicates the MAC address's forwarding status.
1.3.6.1.4.1.171.12.1.2.11.4.1.6ColumnagentFDBSecurityModuleread-onlycurrentThis object is used to indicate which security module created the current MAC address. dot1x: 802.1X. wac: Web-based Access Control. jwac: Web-Based Access Con…
1.3.6.1.4.1.171.12.1.2.12NodeagentARPMgmt
1.3.6.1.4.1.171.12.1.2.12.1ScalaragentARPClearAllStateread-writecurrentUsed to clear all ARP entries.
1.3.6.1.4.1.171.12.1.2.12.2NodeagentGratuitousARPMgmt
1.3.6.1.4.1.171.12.1.2.12.2.1ScalaragentGratuitousARPSendIpifStatusUpStateread-writecurrentThis is used to enable/disable sending of gratuitous ARP request packets while the IPIF interface comes up. This is used to automatically announce the interfac…
1.3.6.1.4.1.171.12.1.2.12.2.2ScalaragentGratuitousARPSendDupIpDetectedStateread-writecurrentThis is used to enable/disable the sending of gratuitous ARP request packets while a duplicate IP is detected. By default, the state is enabled. The duplicate …
1.3.6.1.4.1.171.12.1.2.12.2.3ScalaragentGratuitousARPLearningStateread-writecurrentThis is used to enable/disable learning of an ARP entry in the ARP cache based on the received gratuitous ARP packet. If the switch receives a gratuitous ARP r…
1.3.6.1.4.1.171.12.1.2.12.2.4TableagentGratuitousARPTablenot-accessiblecurrentGratuitous ARP Table Information.
1.3.6.1.4.1.171.12.1.2.12.2.4.1RowagentGratuitousARPEntrynot-accessiblecurrentA list of information from the Gratuitous ARP Table.
1.3.6.1.4.1.171.12.1.2.12.2.4.1.1ColumnagentGratuitousARPInterfaceNameread-onlycurrentThe name of the IP interface.
1.3.6.1.4.1.171.12.1.2.12.2.4.1.2ColumnagentGratuitousARPPeriodicalSendIntervalread-writecurrentThis is used to configure the interval for the periodic sending of gratuitous ARP request packets. 0 means do not send gratuitous ARP request packets periodica…
1.3.6.1.4.1.171.12.1.2.12.2.4.1.3ColumnagentGratuitousARPTrapStateread-writecurrentThis indicates the state of the gratuitous ARP trap. The switch can trap the IP conflict events to inform the administrator. By default, the trap is disabled.
1.3.6.1.4.1.171.12.1.2.12.2.4.1.4ColumnagentGratuitousARPLogStateread-writecurrentThis indicates the state of the gratuitous Log trap. The switch can log the IP conflict events to inform the administrator. By default, the event log is enable…
1.3.6.1.4.1.171.12.1.2.12.3ScalaragentARPTotalARPEntriesread-onlycurrentUsed to display the total number of ARP entries.
1.3.6.1.4.1.171.12.1.2.12.4ScalaragentARPRetryTimesread-writecurrentThis indicates the retry times of the ARP request.
1.3.6.1.4.1.171.12.1.2.13TableswMultiImageCtrlTablenot-accessiblecurrent
1.3.6.1.4.1.171.12.1.2.13.1RowswMultiImageCtrlEntrynot-accessiblecurrentA list of information about multiple image management.
1.3.6.1.4.1.171.12.1.2.13.1.1ColumnswMultiImageCtrlIDread-onlycurrentThe stacking section ID of the firmware image. The stacking section ID = 256 * Unit ID + Image File ID.
1.3.6.1.4.1.171.12.1.2.13.1.2ColumnswMultiImageCtrlActionread-writecurrentThis object indicates the running status of the image which is specified by swMultiImageCtrlID and swMultiImageCtrlUnitID. config-as-bootup-fw (1) - Configured…
1.3.6.1.4.1.171.12.1.2.14ScalaragentOutOfBandDataBitsread-onlycurrentThis object indicates the out-of-band data bits.
1.3.6.1.4.1.171.12.1.2.15ScalaragentOutOfBandParityBitsread-onlycurrentThis object indicates the out-of-band parity bits.
1.3.6.1.4.1.171.12.1.2.16ScalaragentOutOfBandStopBitsread-onlycurrentThis object indicates the out-of-band stop bits.
1.3.6.1.4.1.171.12.1.2.17ScalaragentOutOfBandAutoLogoutConfigread-writecurrentThis object allows the user to specify an out-of-band auto logout time.
1.3.6.1.4.1.171.12.1.2.18NodeagentBscFileSystemMgmt
1.3.6.1.4.1.171.12.1.2.18.1TableagentBscFileSystemTablenot-accessiblecurrentA list of MIB File System Basic Configuration entries supported by the file update of this agent.
1.3.6.1.4.1.171.12.1.2.18.1.1RowagentBscFileSystemEntrynot-accessiblecurrentA File System basic configuration entry that contains objects describing a particular MIB supported by this agent.
1.3.6.1.4.1.171.12.1.2.18.1.1.1ColumnagentBscFileSystemIndexread-onlycurrentThe table index for the file entry. This object describes the file type. runtime-code (1), log-file (2), cfg-file (3), attack-log-file (7)
1.3.6.1.4.1.171.12.1.2.18.1.1.2ColumnagentBscFileSystemDscrread-onlycurrentThe description of the software file purpose in this entry.
1.3.6.1.4.1.171.12.1.2.18.1.1.3ColumnagentBscFileSystemServerAddrread-writecurrentThe IP address where the file to be downloaded is located, or the IP address where the file will be uploaded to.
1.3.6.1.4.1.171.12.1.2.18.1.1.4ColumnagentBscFileSystemServerIPv6Addrread-writecurrentThe IPv6 address where the file is to be downloaded from or uploaded to.
1.3.6.1.4.1.171.12.1.2.18.1.1.5ColumnagentBscFileSystemServerFileNameread-writecurrentThe name of the file to be downloaded from or uploaded to the TFTP server. If agentBscFileSystemDeviceFileName is not set, the switch will default to using the…
1.3.6.1.4.1.171.12.1.2.18.1.1.6ColumnagentBscFileSystemDeviceDriverIDread-writecurrentSpecifies the drive of the device that the firmware to be uploaded/downloaded is located. If none (1) is specified, the switch will default to the current driv…
1.3.6.1.4.1.171.12.1.2.18.1.1.7ColumnagentBscFileSystemDeviceFileNameread-writecurrentThe name of the file to be downloaded to the device, or uploaded from the device. When downloading or uploading, the agentBscFileSystemServerFileName object mu…
1.3.6.1.4.1.171.12.1.2.18.1.1.8ColumnagentBscFileSystemLoadTyperead-writecurrentThis object allows the user to select a download or upload function for the file. Note: For systems that do not support changes to this object, setting a value…
1.3.6.1.4.1.171.12.1.2.18.1.1.9ColumnagentBscFileSystemCtrlUnitIDread-writecurrentSpecifies which unit of the switch stack the firmware image or configuration file should be downloaded from. One or more units can be set in this list. Each bi…
1.3.6.1.4.1.171.12.1.2.18.1.1.10ColumnagentBscFileSystemBootUpImageread-writecurrentThe result of the download will depend on whether the boot_up option has been specified. Case 1: In the case of the master unit providing the file system and t…
1.3.6.1.4.1.171.12.1.2.18.1.1.11ColumnagentBscFileSystemForceAgreeread-writecurrentWhen the force_agree option is specified, the reboot command will be executed immediately without any further confirmation from the user. True: force_agree opt…
1.3.6.1.4.1.171.12.1.2.18.1.1.12ColumnagentBscFileSystemCtrlread-writecurrentThis object allows the user to download runtime software. The settings will take effect when the system restarts. See Note (1) below Note 1: For systems which …
1.3.6.1.4.1.171.12.1.2.18.1.1.13ColumnagentBscFileSystemInterfaceNameread-writecurrentThis node is used to specify the interface name when agentBscFileSystemServerIPv6Addr is the local link address.
1.3.6.1.4.1.171.12.1.2.18.1.1.14ColumnagentBscFileSystemServerDomainNameread-writecurrentThis object indicates the domain name of the TFTP server.
1.3.6.1.4.1.171.12.1.2.18.1.1.15ColumnagentBscFileSystemIncrementread-writecurrentIf increment is specified, then the existing configuration will not be cleared before applying of the new configuration. If it is not specified, then the exist…
1.3.6.1.4.1.171.12.1.2.18.2ScalaragentBscFileSystemSaveConfigDriverIDread-writecurrentThe drive on the device that the configuration file is will be saved to. If none (1) is specified, the switch places the file on the current drive by default.
1.3.6.1.4.1.171.12.1.2.18.3ScalaragentBscFileSystemSaveConfigFileNameread-writecurrentThe name of the configuration file that will be saved to the device. When agentBscFileSystemSaveCfg is set to cfg (2), and if the agentBscFileSystemSaveConfigF…
1.3.6.1.4.1.171.12.1.2.18.4ScalaragentBscFileSystemSaveCfgread-writecurrentThis indicates the method of saving information to the NV-RAM of the device. other (1) - None of the following. cfg (2) - Save configuration. log (3) - Save lo…
1.3.6.1.4.1.171.12.1.2.18.5TableagentFileSystemConfigTablenot-accessiblecurrentThis table indicates the information about the bootup files.
1.3.6.1.4.1.171.12.1.2.18.5.1RowagentFileSystemConfigEntrynot-accessiblecurrentA list of information about the bootup files for each unit of the switch stack.
1.3.6.1.4.1.171.12.1.2.18.5.1.1ColumnagentFileSystemUnitread-onlycurrentThe unit ID.
1.3.6.1.4.1.171.12.1.2.18.5.1.2ColumnagentFileSystemDriverIDread-writecurrentThe drive on the device that the configuration file will be saved to. If none (1) is specified, the switch will place the file to the current drive by default.
1.3.6.1.4.1.171.12.1.2.18.5.1.3ColumnagentFileSystemBootImageread-writecurrentWhen displayed, it shows the current bootup image file name. When set, the set name will be set as the bootup image.
1.3.6.1.4.1.171.12.1.2.18.5.1.4ColumnagentFileSystemBootConfigread-writecurrentWhen displayed, it shows the current bootup configuration file name. When set, the set name will be set as the bootup configuration.
1.3.6.1.4.1.171.12.1.2.18.5.1.5ColumnagentFileSystemActConfigread-writecurrentWhen displayed, it shows null. When set, the set name will be active at once, but the set name will not be set as the bootup configuration.
1.3.6.1.4.1.171.12.1.2.19ScalaragentRebootread-writecurrentUsed to restart the switch.
1.3.6.1.4.1.171.12.1.2.20ScalaragentResetread-writecurrentUsed to reset all switch parameters. none (1): No action. This is the default value of this object. config (2): All parameters are reset to default settings. T…
1.3.6.1.4.1.171.12.1.2.21TableagentFTPFileTablenot-accessiblecurrentA list of the MIB Basic Config entries support files updated by this agent.
1.3.6.1.4.1.171.12.1.2.21.1RowagentFTPFileEntrynot-accessiblecurrentA basic configuration entry containing the objects describing a particular MIB supported by this agent.
1.3.6.1.4.1.171.12.1.2.21.1.1ColumnagentFTPFileIndexread-onlycurrentThe table index for the file entry. This object describes the file type runtime-code (1), log-file (2), cfg-file (3)
1.3.6.1.4.1.171.12.1.2.21.1.2ColumnagentFTPFileDscrread-writecurrentThe description of the software file purpose in this entry. Note: For systems which do not support changes to this object, setting a value for this object will…
1.3.6.1.4.1.171.12.1.2.21.1.3ColumnagentFTPFileLoadTyperead-writecurrentThis object provides the user with a choice of uploading or downloading the selected file. Note: For systems which do not support a change of this object, sett…
1.3.6.1.4.1.171.12.1.2.21.1.4ColumnagentFTPFileAddrread-writecurrentThe IP address that the file to be downloaded is located on, or the IP address where the file will be uploaded to.
1.3.6.1.4.1.171.12.1.2.21.1.5ColumnagentFTPTCPPortread-writecurrentThe TCP port number being used to establish the command connection.
1.3.6.1.4.1.171.12.1.2.21.1.6ColumnagentFTPFileNameread-writecurrentThe name of the file to be downloaded from, or uploaded to, the FTP server.
1.3.6.1.4.1.171.12.1.2.21.1.7ColumnagentFTPUserNameread-writecurrentThis is the user name to enter in upload/download.
1.3.6.1.4.1.171.12.1.2.21.1.8ColumnagentFTPPasswordread-writecurrentThis is the password to enter for an upload/download.
1.3.6.1.4.1.171.12.1.2.21.1.9ColumnagentFTPFileCtrlIDread-writecurrentThe section ID of the firmware image or configuration file. A value of 0 indicates the boot-up firmware image or configuration file.
1.3.6.1.4.1.171.12.1.2.21.1.10ColumnagentFTPFileBIncrementread-writecurrentThis object indicates whether the previous configuration will remain valid or not after downloading the configuration file. True: Keep valid False: Erase.
1.3.6.1.4.1.171.12.1.2.21.1.11ColumnagentFTPFileCtrlread-writecurrentThis object gives the user the option to download runtime software. The setting will take effect when the system restarts. See Note (1) below Note 1: For syste…
1.3.6.1.4.1.171.12.1.2.21.1.12ColumnagentFTPFileBootUpImageread-writecurrentThis object indicates whether to set the special file as a boot up file or not. True: The boot-up option is specified. False: The boot-up option is not specifi…
1.3.6.1.4.1.171.12.1.2.21.1.13ColumnagentFTPFileForceAgreeread-writecurrentWhen the force-agree option is specified, the reboot command will be executed immediately without any further confirmation from the user. True: Force-agree opt…
1.3.6.1.4.1.171.12.1.2.21.1.14ColumnagentFTPFileIPv6Addrread-writecurrentThe IPv6 address where the file is to be downloaded from or uploaded to.
1.3.6.1.4.1.171.12.1.2.21.1.15ColumnagentFTPFileInterfaceNameread-writecurrentThis node is used to specify the interface name when agentFTPFileIPv6Addr is the local link address.
1.3.6.1.4.1.171.12.1.2.21.1.16ColumnagentFTPFileUnitIDread-writecurrentSpecifies which unit of the switch stack the firmware image or configuration file should be downloaded from. One or more units can be set in this list. Each bi…
1.3.6.1.4.1.171.12.1.2.22ScalaragentSnmpTrapStateread-writecurrentThis object indicates if the SNMP trap is enabled or disabled.
1.3.6.1.4.1.171.12.1.2.23NodeagentOutOfBandMgmt
1.3.6.1.4.1.171.12.1.2.23.1ScalaragentOutOfBandMgmtStateread-writecurrentEnables or disables the interface.
1.3.6.1.4.1.171.12.1.2.23.2ScalaragentOutOfBandMgmtIpAddrread-writecurrentThe IP address for out of band management. This object can only take the value of the unicast IP address.
1.3.6.1.4.1.171.12.1.2.23.3ScalaragentOutOfBandMgmtSubnetMaskread-writecurrentThe IP net mask for out of band management.
1.3.6.1.4.1.171.12.1.2.23.4ScalaragentOutOfBandMgmtGatewayread-writecurrentThe gateway for out of band management.
1.3.6.1.4.1.171.12.1.2.23.5ScalaragentOutOfBandMgmtLinkStatusread-onlycurrentThe current Link status for out of band management.
1.3.6.1.4.1.171.12.1.2.24NodeagentTrapMgmt
1.3.6.1.4.1.171.12.1.2.24.1ScalaragentTrapColdStartread-writecurrentWhen enabled (1), whenever the device detects a cold start event, a trap will be sent out.
1.3.6.1.4.1.171.12.1.2.24.2ScalaragentTrapWarmStartread-writecurrentWhen enabled (1), whenever the device detects a warm start event, a trap will be sent out.
1.3.6.1.4.1.171.12.1.2.24.3ScalaragentTrapRmonRisingAlarmread-writecurrentWhen enabled (1), whenever the device detects a RMON rising alarm event , a trap will be sent out.
1.3.6.1.4.1.171.12.1.2.24.4ScalaragentTrapRmonFallingAlarmread-writecurrentWhen enabled (1), whenever the device detects a RMON falling alarm event, a trap will be sent out.
1.3.6.1.4.1.171.12.1.2.24.5ScalaragentTrapCfgSaveread-writecurrentWhen enabled (1), whenever the device detects a configuration saving completed event, a trap will be sent out.
1.3.6.1.4.1.171.12.1.2.24.6ScalaragentTrapCfgUploadread-writecurrentWhen enabled (1), whenever the device detects a configuration uploading completed event, a trap will be sent out.
1.3.6.1.4.1.171.12.1.2.24.7ScalaragentTrapCfgDownloadread-writecurrentWhen enabled (1), whenever the device detects a configuration downloading completed event, a trap will be sent out
1.3.6.1.4.1.171.12.1.2.25TableagentFTPFileSystemTablenot-accessiblecurrentThe FTP management table for the file system
1.3.6.1.4.1.171.12.1.2.25.1RowagentFTPFileSystemEntrynot-accessiblecurrentA File System basic configuration entry that contains objects describing a particular MIB supported by this agent.
1.3.6.1.4.1.171.12.1.2.25.1.1ColumnagentFTPFileSystemIndexnot-accessiblecurrentThe table index for the file entry.
1.3.6.1.4.1.171.12.1.2.25.1.2ColumnagentFTPFileSystemDscrread-onlycurrentThe description of the software file purpose in this entry.
1.3.6.1.4.1.171.12.1.2.25.1.3ColumnagentFTPFileSystemLoadTyperead-writecurrentThis object allows the user to select a download or upload function for the file.
1.3.6.1.4.1.171.12.1.2.25.1.4ColumnagentFTPFileSystemAddressTyperead-writecurrentThe address type of agentFTPFileSystemAddress.
1.3.6.1.4.1.171.12.1.2.25.1.5ColumnagentFTPFileSystemAddressread-writecurrentThis object indicates the FTP server address.
1.3.6.1.4.1.171.12.1.2.25.1.6ColumnagentFTPFileSystemTCPPortread-writecurrentThe TCP port number being used to establish the control connection.
1.3.6.1.4.1.171.12.1.2.25.1.7ColumnagentFTPFileSystemServerFileNameread-writecurrentThe name of the file to be downloaded from or uploaded to the FTP server.
1.3.6.1.4.1.171.12.1.2.25.1.8ColumnagentFTPFileSystemDeviceFileNameread-writecurrentThe name of the file to be downloaded to the device, or uploaded from the device. If agentFTPFileSystemDeviceFileName is not set, the switch will default to th…
1.3.6.1.4.1.171.12.1.2.25.1.9ColumnagentFTPFileSystemUserNameread-writecurrentThis object indicates the user name to access the FTP server.
1.3.6.1.4.1.171.12.1.2.25.1.10ColumnagentFTPFileSystemPasswordread-writecurrentThis object indicates the password to access the FTP server.
1.3.6.1.4.1.171.12.1.2.25.1.11ColumnagentFTPFileSystemCtrlUnitIDread-writecurrentSpecifies which unit of the switch stack the firmware image or configuration file should be downloaded from. One or more units can be set in this list. Each bi…
1.3.6.1.4.1.171.12.1.2.25.1.12ColumnagentFTPFileSystemBootUpImageread-writecurrentThis object indicates whether to set the special file as the boot up file or not. True: The boot-up option is specified. False: The boot-up option is not speci…
1.3.6.1.4.1.171.12.1.2.25.1.13ColumnagentFTPFileSystemCtrlread-writecurrentThis object allows the user to execute an FTP download/upload.
1.3.6.1.4.1.171.12.1.2.26ScalaragentBscCMDLogStateread-writecurrentThis object indicates the command logging state.
1.3.6.1.4.1.171.12.1.2.27ScalaragentBscBroadcastPingReplyStateread-writecurrentThis object indicates the broadcast ping reply state.
1.3.6.1.4.1.171.12.1.2.28NodeagentBscTftpConfigMgmt
1.3.6.1.4.1.171.12.1.2.28.1ScalaragentBscTftpCfgFirmwareFileread-writecurrentThe firmware pathname that needs to be downloaded/uploaded from/to the TFTP server.
1.3.6.1.4.1.171.12.1.2.28.2ScalaragentBscTftpCfgConfigFileread-writecurrentThe configuration pathname that needs to be downloaded/uploaded from/to the TFTP server.
1.3.6.1.4.1.171.12.1.2.28.3ScalaragentBscTftpCfgLogFileread-writecurrentThe log pathname that needs to be uploaded to the TFTP server.
1.3.6.1.4.1.171.12.1.2.28.4ScalaragentBscTftpCfgAttackLogFileread-writecurrentThe attack log pathname that needs to be uploaded to the TFTP server.
1.3.6.1.4.1.171.12.1.2.28.5ScalaragentBscTftpCfgCertificateFileread-writecurrentThe certificate pathname that needs to be downloaded from the TFTP server.
1.3.6.1.4.1.171.12.1.2.28.6ScalaragentBscTftpCfgKeyFileread-writecurrentThe key pathname that needs to be downloaded from the TFTP server.
1.3.6.1.4.1.171.12.1.2.28.7ScalaragentBscTftpCfgTechSuooprtFileread-writecurrentThe technique's support information pathname that needs to be uploaded to the TFTP server.
1.3.6.1.4.1.171.12.1.2.28.8ScalaragentBscTftpCfgDebugLogFileread-writecurrentThe debug log pathname that needs to be uploaded to the TFTP server.
1.3.6.1.4.1.171.12.1.2.28.9ScalaragentBscTftpCfgSIMFirmwareFileread-writecurrentThe firmware pathname that needs to be downloaded/uploaded from/to the TFTP server when it is SIM enabled.
1.3.6.1.4.1.171.12.1.2.28.10ScalaragentBscTftpCfgSIMConfigFileread-writecurrentThe configuration pathname that needs to be downloaded/uploaded from/to the TFTP server when it is SIM enabled.
1.3.6.1.4.1.171.12.1.2.28.11ScalaragentBscTftpCfgSIMLogFileread-writecurrentThe log pathname that needs to be uploaded to the TFTP server when it is SIM enabled.
1.3.6.1.4.1.171.12.1.2.28.12ScalaragentBscTftpCfgServerIPAddrread-writecurrentThe IPv4 address of the TFTP server.
1.3.6.1.4.1.171.12.1.2.28.13ScalaragentBscTftpCfgServerIPv6Addrread-writecurrentThe IPv6 address of the TFTP server.
1.3.6.1.4.1.171.12.1.2.28.14ScalaragentBscTftpCfgServerDomainNameread-writecurrentThe domain name of the TFTP server.
1.3.6.1.4.1.171.12.1.2.29ScalaragentBscCommunityEncryptionStateread-writecurrentThis object indicates the encryption state on the SNMP community string.
1.3.6.1.4.1.171.12.1.3NodeagentIpProtoConfig
1.3.6.1.4.1.171.12.1.3.1ScalaragentIpNumOfIfread-onlycurrentThe total number of IP interfaces supported by this agent.
1.3.6.1.4.1.171.12.1.3.2ScalaragentIpTftpServerAddrread-writeobsoleteThe IP address of the TFTP Server.
1.3.6.1.4.1.171.12.1.3.3ScalaragentIpGetIpFromread-writecurrentThis object indicates if the agent will get its system IP address from a Bootp/DHCP server at start up.
1.3.6.1.4.1.171.12.1.3.4ScalaragentIpAutoconfigread-writecurrentIndicates the status of automatically getting the configuration information from a TFTP server connected to the device.
1.3.6.1.4.1.171.12.1.3.5ScalaragentIpAutoconfigTimeoutread-writecurrentThis timer is used to limit the length of time for getting the configuration information from a TFTP server connected to the device.
1.3.6.1.4.1.171.12.1.4NodeagentIpTrapManager
1.3.6.1.4.1.171.12.1.4.2TableagentTrapManagerTablenot-accessiblecurrentA list of trap managers that the SNMP traps will be sent to.
1.3.6.1.4.1.171.12.1.4.2.1RowagentTrapManagerEntrynot-accessiblecurrentEach entry contains the particular trap manager's settings.
1.3.6.1.4.1.171.12.1.4.2.1.1ColumnagentTrapManagerIndexnot-accessiblecurrentA value that uniquely identifies trapDestEntry.
1.3.6.1.4.1.171.12.1.4.2.1.2ColumnagentTrapManagerIpAddrread-writecurrentThe destination IP address for SNMP traps.
1.3.6.1.4.1.171.12.1.4.2.1.3ColumnagentTrapManagerCommread-writecurrentThe community string used to encode SNMP trap packets being sent to the trap manager.
1.3.6.1.4.1.171.12.1.4.2.1.4ColumnagentTrapManagerMsgVerread-writecurrentThis object indicates the version of trap packets that will be sent to this trap manager. The default setting is SNMP Agent Version Dependent. Note: Because so…
1.3.6.1.4.1.171.12.1.4.2.1.5ColumnagentTrapManagerStatusread-writecurrentThis object indicates whether or not the trap should be sent to the trap manager.
1.3.6.1.4.1.171.12.1.7NodeagentNotify
1.3.6.1.4.1.171.12.1.7.1NodeagentNotifMgmt
1.3.6.1.4.1.171.12.1.7.1.2NodenotifFirmwareMgmt
1.3.6.1.4.1.171.12.1.7.2NodeagentNotifFirmware
1.3.6.1.4.1.171.12.1.7.2.0NodeagentNotifyPrefix
1.3.6.1.4.1.171.12.1.7.2.0.1NotificationagentsystemRestartcurrentThis trap contains the reboot information.
1.3.6.1.4.1.171.12.1.7.2.0.2NotificationagentSaveToNVRAMcurrentThis trap is sent whenever all the device configuration has been saved to NV-RAM.
1.3.6.1.4.1.171.12.1.7.2.0.3NotificationagentFileTransferStatusChangecurrentFile transfer status change notification.
1.3.6.1.4.1.171.12.1.7.2.0.4NotificationagentSetToFactoryDefaultcurrentThis trap is sent whenever the 'set to factory default' setting has been processed.
1.3.6.1.4.1.171.12.1.7.2.0.5NotificationagentGratuitousARPTrapcurrentThis trap is sent when there is an IP address conflict.
1.3.6.1.4.1.171.12.1.7.2.0.6NotificationagentLoginFailTrapcurrentThe trap is sent when a login has failed through one of the login types (console, Telnet, web, SSL or SSH).
1.3.6.1.4.1.171.12.1.7.2.0.7NotificationagentFirmwareUpgradecurrentThis trap is sent when the process of upgrading the firmware via SNMP has finished.
1.3.6.1.4.1.171.12.1.7.2.0.8NotificationagentAccessFlashFailedcurrentThe trap is sent when access to the flash fails.
1.3.6.1.4.1.171.12.1.7.2.0.9NotificationagentCfgOperCompleteTrapcurrentThe trap is sent when the configuration is completely saved, uploaded or downloaded.
1.3.6.1.4.1.171.12.1.7.2.1NodenotificationBindings
1.3.6.1.4.1.171.12.1.7.2.1.1ScalarunitIDaccessible-for-notifycurrentThe unit ID of the device which triggered the event.
1.3.6.1.4.1.171.12.1.7.2.1.2ScalartrapInfosystemRestartread-onlycurrentThis object indicates the last time the device rebooted.
1.3.6.1.4.1.171.12.1.7.2.1.3ScalaragentGratuitousARPIpAddraccessible-for-notifycurrentA duplicate IP address with the switch already exists.
1.3.6.1.4.1.171.12.1.7.2.1.4ScalaragentGratuitousARPMacAddraccessible-for-notifycurrentThis object is the MAC address of the device which has the duplicate IP address.
1.3.6.1.4.1.171.12.1.7.2.1.5ScalaragentGratuitousARPPortNumberaccessible-for-notifycurrentThis indicates the portNum with a string. For example, if the device is in standalone mode, and the port number is 23, the string should be 23. If the device i…
1.3.6.1.4.1.171.12.1.7.2.1.6ScalaragentLoginTypeaccessible-for-notifycurrentThe type is the user login method type.
1.3.6.1.4.1.171.12.1.7.2.1.7ScalaragentLoginAAAMethodaccessible-for-notifycurrentThis method is the AAA login method.
1.3.6.1.4.1.171.12.1.7.2.1.8ScalaragentLoginUserNameaccessible-for-notifycurrentThis object is the name of the user that failed to login to the switch.
1.3.6.1.4.1.171.12.1.7.2.1.9ScalaragentLoginIpAddraccessible-for-notifycurrentThis object is the login type from the IP address.
1.3.6.1.4.1.171.12.1.7.2.1.10ScalaragentLoginMacAddraccessible-for-notifycurrentThis object is the login type from a MAC address.
1.3.6.1.4.1.171.12.1.7.2.1.11ScalaragentLoginAAAServerAddraccessible-for-notifycurrentThis object is the login type through a console authenticated by an AAA server.
1.3.6.1.4.1.171.12.1.7.2.1.12ScalaragentLoginFailInfoaccessible-for-notifycurrentThis object indicates the reason for the login failure.
1.3.6.1.4.1.171.12.1.7.2.1.13ScalaragentAccessFlashOperaccessible-for-notifycurrentThis object indicates the operation of the access flash failure.
1.3.6.1.4.1.171.12.1.7.2.1.14ScalaragentAccessFlashAddraccessible-for-notifycurrentThis object indicates the address of the access flash failure.
1.3.6.1.4.1.171.12.1.7.2.1.15ScalaragentCfgOperateaccessible-for-notifycurrentThis object indicates the operation type of the configuration.
Type Definitions
NameSyntaxStatusDescription
Ipv6AddressOCTET STRING (SIZE (16)) UnitList ::= OCTET STRING(SIZE (0..3))currentThis data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order.
MIB Viewer