AI-AP-MIB
66 objects
No module-level DESCRIPTION found.
Imported Objects
| ARUBA-MIB | aiEnterpriseMibModules |
| SNMPv2-CONF | OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE snmpModules |
| SNMPv2-TC | DateAndTime DisplayString MacAddress PhysAddress RowStatus StorageType TestAndIncr TEXTUAL-CONVENTION TimeInterval TruthValue |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| ArubaAccessPointMode | INTEGER{ airMonitor(1), accessPoint(2), accessPointAndMonitor(3), meshPortal(4), meshPoint(5), rfprotectSensor(6), spectrumSensor(7) } | current | The mode of the access point. |
| ArubaACLAction | INTEGER { deny(1), permit(2), srcNAT(3), dstNAT(4), redirect(5) } | current | Represents the Actions in an ACL rule. |
| ArubaACLDomain | INTEGER { alias(1), any(2), user(3), host(4), network(5) } | current | Represents both the source and destination to which an ACL rule will be applied. |
| ArubaACLNetworkServiceType | INTEGER { alias(1), any(2), tcp(3), udp(4), protocol(5) } | current | Represents the network service in an ACL Rule. |
| ArubaActiveState | INTEGER { active(1), inactive(2) } | current | Represents if a feature is active or inactive. |
| ArubaAddressType | INTEGER{ srcAddress(1), dstAddress(2), bssid(3) } | current | Address Type. |
| ArubaAntennaSetting | INTEGER { notPresent(1), enabled(2), disabled(3) } | current | Represents the status of the external antenna. |
| ArubaAPConductorStatus | INTEGER { up(1), down(2), move(3) } | current | AP status as seen by the conductor controller (used to indicate a status change). |
| ArubaAPMasterStatus | INTEGER { up(1), down(2), move(3) } | obsolete | AP status as seen by the master controller (used to indicate a status change). **NOTE: this textual convention is obsoleted and replaced by ArubaAPConductorStatus. |
| ArubaAPMatchMethod | INTEGER { notApplicable(0), exactMatch(1), plusOneMatch(2), minusOneMatch(3), ouiMatch(4) } | current | Represents the match method of a suspected rogue AP. |
| ArubaAPMatchType | INTEGER { unknown(0), configuredWiredMac(1), ethernetWiredMac(2), apWiredMac(3), externalWiredMac(4), manual(5), baseBSSIDOverride(6), mms(7), ethernetGatewayWiredMac(8), classificationDisabled(9), apBSSID(10), propagatedEthernetWiredMac(11), apRule(12), systemWiredMac(13), systemGatewayMac(14) } | current | Represents the match type of a suspected rogue AP. |
| ArubaAPStatus | INTEGER { up(1), down(2) } | current | The status of the access point. |
| ArubaAPUplinkChangeReason | INTEGER { linkFailure(1), vpnFailure(2), preemption(3), internetFailover(4) } | current | Used to specify the reason for AP uplink change. linkFailure - The uplink went down vpnFailure - VPN tunnel could not be sustained using the uplink preemption - The uplink was pre-empted by a higher-priority uplink |
| ArubaAPUplinkType | INTEGER { ethernet(1), usb(2), pppoe(3), wifi(4) } | current | AP uplink type |
| ArubaARMChangeReason | INTEGER { radarDetected(1), radarCleared(2), txHang(3), txHangClear(4), fortyMhzIntol(5), cancel40mhzIntol(6), fortyMhzAlign(7), armInterference(8), armInvalidCh(9), armErrorThresh(10), armNoiseThresh(11), armEmptyCh(12), armRogueCont(13), armDecreasePower(14), armIncreasePower(15), armTurnOffRadio(16), armTurnOnRadio(17) } | current | The reason for ARM based change. |
| ArubaAuthenticationMethods | INTEGER { none(0), web(1), mac(2), vpn(3), dot1x(4), kerberos(5), secureId(7), pubcookie(15), xSec(16), xSecMachine(17), via-vpn(28), other(255) } | current | Authentication Method. |
| ArubaAuthServerType | INTEGER{ internaldb(1), radius(2), ldap(3), kerberos(4), tacacs(5) } | current | The type of the auth server. |
| ArubaBlackListReason | INTEGER { userDefined(1), mitmAttack(2), authFailure(3), pingFlood(4), sessionFlood(5), synFlood(6), sessionBlacklist(7), ipSpoofing(8), esiBlacklist(9), other(100) } | obsolete | Black List Reason **NOTE: this textual convention is obsoleted and replaced by ArubaDenyListReason. |
| ArubaCallStates | INTEGER { idle(0), initiated(1), connecting(2), delivered(3), connected(4), offered(5), alerting(6), releasing(7), cancelling(8), challenging(9), transient(10), blockwait(11), succ(12), fail(13), aborted(14), blocked(15) } | current | The Call state. |
| ArubaCardType | INTEGER { lc1(1), lc2(2), sc1(3), sc2(4), sw2400(5), sw800(6), sw200(7), m3mk1(8), sw3200(9), sw3400(10), sw3600(11), sw650(12), sw651(13), reserved1(14), reserved2(15), sw620(16) } | current | Type of the hardware module. |
| ArubaConfigurationChangeType | INTEGER { create(1), delete(2), modify(3) } | current | Configuration Change Types. |
| ArubaConfigurationState | INTEGER { success(1), error(2) } | current | Configuration Transfer Types. |
| ArubaDaysOfWeek | INTEGER { sun(1), mon(2), tue(3), wed(4), thu(5), fri(6), sat(7) } | current | Represents the Actions in an ACL rule. |
| ArubaDBType | INTEGER { mssql(1), mysql(2) } | current | DataBase Type. |
| ArubaDenyListReason | INTEGER { userDefined(1), mitmAttack(2), authFailure(3), pingFlood(4), sessionFlood(5), synFlood(6), sessionDenylist(7), ipSpoofing(8), esiDenylist(9), other(100) } | current | Deny List Reason. |
| ArubaDot1dState | INTEGER { disabled(1), blocked(2), listening(3), learning(4), forwarding(5) } | current | Represents the controller port spanning tree state. |
| ArubaEnableValue | INTEGER { enabled(1), disabled(2) } | current | Represents a Flag which is either Enabled or Disabled. |
| ArubaEncryptionMethods | BITS{ disabled(0), static-wep(1), dynamic-wep(2), static-wpa(3), dynamic-wpa(4), wpa2-psk-aes(5), wpa2-8021x-aes(6), wpa2PreAuth(7), xsec(8), wpa-psk-aes(9), wpa-aes(10), wpa2-psk-tkip(11), wpa2-8021x-tkip(12), bSec-128(13), bSec-256(14), owe-aes(16), wpa3-sae-aes(17), wpa3-cnsa(18), wpa3-aes-ccm-128(19), mpsk-aes(21), wpa3-aes-gcm-256(22) } | current | Represents the Actions in an ACL rule. |
| ArubaEncryptionType | INTEGER { none(0), static-wep(1), dynamic-wep(2), wpa-psk-tkip(3), wpa-tkip(4), wpa-psk-aes(5), wpa-aes(6), wpa2-psk-tkip(7), wpa2-tkip(8), wpa2-psk-aes(9), wpa2-aes(10), xSec(11), bSec-128(12), bSec-256(13), aes-128-cmac(14), unknown(15), ft-psk(16), ft-8021x(17), wpa3-cnsa(18), owe-aes(20), wpa3-sae-aes(21), wpa3-aes-gcmp-256(22) } | current | Encryption Method. |
| ArubaEnet1Mode | INTEGER { activeStandby(1), tunnel(2), bridge(3), notApplicable(4), split(5) } | current | Represents the Mode of the Ethernet port on the Access Point |
| ArubaESIServerMode | INTEGER { bridged(1), routed(2), nat(3) } | current | The mode of the ESI server. |
| ArubaESIServerStatus | INTEGER { up(1), down(2) } | current | The status of the ESI server. |
| ArubaFrameType | INTEGER { associateRequest(0), associateResponse(1), reassociateRequest(2), reassociateResponse(3), probeRequest(4), probeResponse(5), beacon(8), atim(9), disassociate(10), auth(11), deauth(12) } | current | Represents the Frame type. |
| ArubaHashAlgorithms | INTEGER { md5(1), sha(2) } | current | Represents the Actions in an ACL rule. |
| ArubaHTExtChannel | INTEGER { none(1), above(2), below(3) } | current | Represents the extension channel offset relative to the current channel. |
| ArubaHTMode | INTEGER { none(1), ht20(2), ht40(3), vht20(4), vht40(5), vht80(6), vht160(7), vht80plus80(8), he20(9), he40(10), he80(11), he160(12), he80plus80(13) } | current | Represents the HT status of the access point or client. |
| ArubaHTRate | INTEGER { unknown(0), ht6dot5(1), ht13(2), ht13dot5(3), ht15(4), ht19dot5(5), ht26(6), ht27(7), ht30(8), ht39(9), ht40dot5(10), ht45(11), ht52(12), ht54(13), ht58dot5(14), ht60(15), ht65(16), ht78(17), ht81(18), ht90(19), ht104(20), ht108(21), ht117(22), ht120(23), ht121dot5(24), ht130(25), ht135(26), ht150(27), ht162(28), ht180(29), ht216(30), ht240(31), ht243(32), ht270(33), ht300(34) } | current | Represents HT rate |
| ArubaIfType | INTEGER { port(1), vlan(2), tunnel(3), loopback(4) } | current | The type of interface referred to by the value of ifIndex. |
| ArubaMeshRole | INTEGER { nonmesh(0), point(1), portal(2) } | current | Mesh role |
| ArubaMonAuthAlgorithm | INTEGER { none(0), psk(1), dot1x(2), ft8021x(3), ftpsk(4), dot1x256(5), psk256(6), tdls(7), sae(8), ftsae(9), other(10), suiteb(11), owe(12) } | current | Represents the WPA authentication algorithm supported by the access point. |
| ArubaMonEncryptionCipher | INTEGER { none(0), wep40(1), wep104(2), tkip(3), aesccmp(4), other(5), gcm256(6) } | current | Represents the WPA encryption cipher supported by the access point. |
| ArubaMonEncryptionType | INTEGER { open(0), wep(1), wpa(2), wpa2(3), wpa3(4) } | current | Represents the encryption type supported by the access point. |
| ArubaMonitorMode | INTEGER { unknown(0), all(1), none(2), mixed(3) } | current | Represents whether the AP has any radios dedicated to monitoring. |
| ArubaOperStateValue | INTEGER { up(1), down(2), testing(3) } | current | Represents Operational state of an interface. |
| ArubaPhyType | INTEGER { dot11a(1), dot11b(2), dot11g(3), dot11ag(4), wired(5), dot11ax6ghz(6) } | current | Represents the PHY-type of the access point or client. Wired clients will show 'wired' in user MIB entries. |
| ArubaPoeState | INTEGER { disabled(1), enabled(2), enabledCisco(3), notAvailable(4) } | current | Represents the POE mode. |
| ArubaPortalServerDownReason | INTEGER { connectFail(1) } | current | Used to specify the reason for Portal server down. connectFail - Connect Portal server fail |
| ArubaPortDuplex | INTEGER { half(1), full(2), auto(3) } | current | Port Duplexity. |
| ArubaPortMode | INTEGER { access(1), dot1q(2) } | current | Represents the controller port mode. |
| ArubaPortSpeed | INTEGER { speed10Mbps(1), speed100Mbps(2), speed1000Mbps(3), speedAuto(4), speed10Gbps(5) } | current | Port Speed. |
| ArubaPortType | INTEGER { fastethernet(1), gigabitethernet(2), xgigabitethernet(3) } | current | Port Type. |
| ArubaRogueApType | INTEGER { valid(1), interfering(2), unsecure(3), dos(4), unknown(5), knownInterfering(6), suspectedUnsecure(7) } | current | Represents the Rogue AP Type. |
| ArubaStationType | INTEGER { valid(1), interfering(2), dos(3) } | current | Represents the station type. |
| ArubaSubAuthenticationMethods | INTEGER { authPAP(1), authCHAP(2), authMSCHAP(3), authMSCHAPv2(4), eapTLS(5), eapTTLS(6), eapLEAP(7), eapMD5(8), eapPEAP(9) } | current | Sub Authentication Method (e.g. EAP type). |
| ArubaSupportStatus | INTEGER { unsupported(1), supported(2) } | current | Represents if a feature is supported or unsupported. |
| ArubaSwitchRole | INTEGER { conductor(1), local(2), backupconductor(3) } | current | Represents the role of the controller |
| ArubaUnprovisionedStatus | INTEGER { yes(1), no(2) } | current | Represents whether the AP is provisioned or not. |
| ArubaUSBStatus | INTEGER { unknown(0), notPresent(1), inactive(2), active(3) } | current | USB device status |
| ArubaUserForwardMode | INTEGER { tunnel-encrypted(0), bridge(1), tunnel-decrypted(2), split-tunnel(3) } | current | User Forwarding Mode. |
| ArubaVlanValidRange | INTEGER(1..4095) | current | Represents the Valid Vlan Id Range. |
| ArubaVoiceCacBit | BITS { cacActiveLoadBalancing(0), cacHighCapThresholdReached(1), cacHandRsrvThresholdReached(2), cacPeakCapacityReached(3) } | current | Voice CAC bit flags |
| ArubaVoiceCdrDirection | INTEGER { og(0), ic(1) } | current | VoIP CDR direction |
| ArubaVoipProtocol | INTEGER { sccp(1), svp(2), vocera(3), sip(9), ua(11) } | current | VoIP protocol used |
| ArubaVoipProtocolType | INTEGER{ sccp(1), svp(2), vocera(3), sip(4), unknown(10) } | current | The type of VoIP protocols supported. |
| ArubaVoipRegState | INTEGER { unknown(0), registering(1), unregistering(2), challenge(3), registered(4), unregistered(5) } | current | VoIP registered state |
| ArubaVrrpState | INTEGER { initialize(1), backup(2), master(3) } | current | DataBase Type. |