ALTEON-TIGON-SWITCH-MIB
170 objects
No module-level DESCRIPTION found.
Imported Objects
| ALTEON-ROOT-MIB | switch |
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | BEGIN IMPORTS enterprises Counter Gauge IpAddress mgmt NetworkAddress |
| RFC1213-MIB | DisplayString PhysAddress |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1872.2.1.1 | Nodehardware | |||
| 1.3.6.1.4.1.1872.2.1.1.1 | ScalarhwPartNumber | read-only | mandatory | The hardware part number of the Alteon Switch. |
| 1.3.6.1.4.1.1872.2.1.1.2 | ScalarhwRevision | read-only | mandatory | The hardware revision. If the revision is not available, a zero length string should be returned. |
| 1.3.6.1.4.1.1872.2.1.1.3 | ScalarhwPowerSupplyStatus | read-only | mandatory | The status of the internal power supply. |
| 1.3.6.1.4.1.1872.2.1.1.4 | ScalarhwRedundantPSPresent | read-only | mandatory | Existence of redundant power supply. |
| 1.3.6.1.4.1.1872.2.1.1.5 | ScalarhwRedundantPSStatus | read-only | mandatory | The status of the redundant power supply. |
| 1.3.6.1.4.1.1872.2.1.1.6 | ScalarhwSensor1Temp | read-only | mandatory | The temperature of the rear left sensor in degrees Celsius. |
| 1.3.6.1.4.1.1872.2.1.1.7 | ScalarhwSensor2Temp | read-only | mandatory | The temperature of the rear middle sensor in degrees Celsius. |
| 1.3.6.1.4.1.1872.2.1.1.8 | ScalarhwSensor3Temp | read-only | mandatory | The temperature of the front middle sensor in degrees Celsius. |
| 1.3.6.1.4.1.1872.2.1.1.9 | ScalarhwSensor4Temp | read-only | mandatory | The temperature of the front right sensor in degrees Celsius. |
| 1.3.6.1.4.1.1872.2.1.2 | Nodeagent | |||
| 1.3.6.1.4.1.1872.2.1.2.1 | NodeagGeneral | |||
| 1.3.6.1.4.1.1872.2.1.2.1.1 | ScalaragSaveConfiguration | read-write | mandatory | This is an action object to write current configuration to nonvolatile storage. When issued with the saveActive, the active configuration in flash is saved to … |
| 1.3.6.1.4.1.1872.2.1.2.1.2 | ScalaragApplyConfiguration | read-write | mandatory | This is an action object to apply the changes made to configuration of the switch. By setting the value to apply(2), all the changes made since the last apply … |
| 1.3.6.1.4.1.1872.2.1.2.1.3 | ScalaragApplyPending | read-only | mandatory | This object, when read, gives the user information whether an apply action is needed and that the configuration has been chaged by the user actions. The user t… |
| 1.3.6.1.4.1.1872.2.1.2.1.4 | ScalaragReset | read-write | mandatory | This is an action object to reboot the agent. other(1) is returned always when read. The following values are writable: coldReset(2)... warmReset(3)... |
| 1.3.6.1.4.1.1872.2.1.2.1.5 | ScalaragConfigForNxtReset | read-write | mandatory | The configuration information to be loaded from at next reset. The following values are writable: active(2)...active configuration block backup(3)...backup con… |
| 1.3.6.1.4.1.1872.2.1.2.1.6 | ScalaragImageForNxtReset | read-write | mandatory | The software image to be booted from at next reset. The following values are writable: image1(2)...image 1 image2(3)...image 2 |
| 1.3.6.1.4.1.1872.2.1.2.1.7 | ScalaragSoftwareVersion | read-only | mandatory | The version of the software image that is currently running on the system in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if … |
| 1.3.6.1.4.1.1872.2.1.2.1.8 | ScalaragBootVer | read-only | mandatory | The version of the boot code in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available. |
| 1.3.6.1.4.1.1872.2.1.2.1.9 | ScalaragImage1Ver | read-only | mandatory | The version of the software image stored in image 1 storage in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if version is not… |
| 1.3.6.1.4.1.1872.2.1.2.1.10 | ScalaragImage2Ver | read-only | mandatory | The version of the software image stored in image 2 storage in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if version is not… |
| 1.3.6.1.4.1.1872.2.1.2.1.11 | ScalaragRtcDate | read-write | mandatory | The date on the real time clock in the form of 'mm/dd/yy'. A zero length string is returned if date is not available. |
| 1.3.6.1.4.1.1872.2.1.2.1.12 | ScalaragRtcTime | read-write | mandatory | The time on the real time clock in the form of 'hh:mm:ss'. A zero length string is returned if time is not available. |
| 1.3.6.1.4.1.1872.2.1.2.1.13 | ScalaragTftpServerIpAddr | read-write | mandatory | The TFTP server IP address. |
| 1.3.6.1.4.1.1872.2.1.2.1.14 | ScalaragTftpImageFileName | read-write | mandatory | The image file name to be downloaded. |
| 1.3.6.1.4.1.1872.2.1.2.1.15 | ScalaragTftpImage | read-write | mandatory | Whether the image file should be loaded in image1 or image2 in flash. |
| 1.3.6.1.4.1.1872.2.1.2.1.16 | ScalaragTftpDownload | read-write | mandatory | This is an action object to cause to download software image according to the setup of agTftpServerIpAddr, agTftpImageFileName, agTftpImage when download(2) is… |
| 1.3.6.1.4.1.1872.2.1.2.1.17 | ScalaragLastSetErrorReason | read-only | mandatory | The error reason of the last SET failure. |
| 1.3.6.1.4.1.1872.2.1.2.1.18 | ScalaragTftpServer | read-write | mandatory | The TFTP server IP address or domain name. |
| 1.3.6.1.4.1.1872.2.1.2.1.19 | ScalaragTftpCfgFileName | read-write | mandatory | The configuration file name. |
| 1.3.6.1.4.1.1872.2.1.2.1.20 | ScalaragTftpDumpFileName | read-write | mandatory | The file name for core dump. |
| 1.3.6.1.4.1.1872.2.1.2.1.21 | ScalaragTftpAction | read-write | mandatory | This is an action object to perform various TFTP Get or Put functions. The TFTP sever is specified in agTftpServer object. img-get(2) - Download switch image f… |
| 1.3.6.1.4.1.1872.2.1.2.1.22 | ScalaragTftpLastActionStatus | read-only | mandatory | The recorded status of the previous TFTP activity. |
| 1.3.6.1.4.1.1872.2.1.2.1.23 | ScalaragRevert | read-write | mandatory | This is an action object to revert the unapplied changes made to the switch. By setting the value to revert(2), all the unapplied changes will be reverted. Thi… |
| 1.3.6.1.4.1.1872.2.1.2.1.24 | ScalaragRevertApply | read-write | mandatory | This is an action object to revert the unsaved changes made to the switch. By setting the value to revertApply(2), all the unsaved as well as unapplied changes… |
| 1.3.6.1.4.1.1872.2.1.2.1.25 | ScalaragEnabledSwFeatures | read-only | mandatory | The software features that are enabled on the switch. |
| 1.3.6.1.4.1.1872.2.1.2.1.26 | ScalaragClrSyslogMsgs | read-write | mandatory | Clears all current Syslog messages. |
| 1.3.6.1.4.1.1872.2.1.2.1.27 | ScalaragSavePending | read-only | mandatory | This object, when read, gives the user information whether an save action is needed and that the configuration has been applied but not saved to the flash. |
| 1.3.6.1.4.1.1872.2.1.2.1.28 | ScalaragEnabledGslbKey | read-only | mandatory | Query if software key Global slb enabled on switch. |
| 1.3.6.1.4.1.1872.2.1.2.1.29 | ScalaragEnabledBwmKey | read-only | mandatory | Query if software key Bandwidth Mgmt. enabled on switch. |
| 1.3.6.1.4.1.1872.2.1.2.1.30 | ScalaragSlotNumber | read-only | mandatory | Identifies the slot in which this switch is installed. If the agent implementing this MIB is not a blade in a chassis this value has no meaning. |
| 1.3.6.1.4.1.1872.2.1.2.1.31 | ScalaragEnabledRurlKey | read-only | mandatory | The status of the RURL software key. |
| 1.3.6.1.4.1.1872.2.1.2.2 | NodeagGeneralConfig | |||
| 1.3.6.1.4.1.1872.2.1.2.2.1 | ScalaragNewCfgSyslogHost | read-write | mandatory | The syslog host IP address, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.2 | ScalaragCurCfgSyslogHost | read-only | mandatory | The syslog host IP address, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.3 | ScalaragNewCfgBootp | read-write | mandatory | Enable or disable the use of BootP, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.4 | ScalaragCurCfgBootp | read-only | mandatory | Enable or disable the use of BootP, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.5 | ScalaragNewCfgSpanningTree | read-write | mandatory | Turn On or Off Spanning Tree Protocol for the switch, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.6 | ScalaragCurCfgSpanningTree | read-only | mandatory | The state of Spanning Tree Protocol for the switch, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.7 | ScalaragTrapHostTableMaxEnt | read-only | mandatory | The maximum number of rows in the trap host table. |
| 1.3.6.1.4.1.1872.2.1.2.2.8 | TableagCurCfgTrapHostTable | not-accessible | mandatory | The table of trap hosts which to send SNMP traps in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.8.1 | RowagCurCfgTrapHostEntry | not-accessible | mandatory | A row in the trap host table in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.8.1.1 | ColumnagCurCfgTrapHostIndx | read-only | mandatory | The index of the row in trap host table. |
| 1.3.6.1.4.1.1872.2.1.2.2.8.1.2 | ColumnagCurCfgTrapHostIpAddr | read-only | mandatory | The IP address of a trap host. |
| 1.3.6.1.4.1.1872.2.1.2.2.8.1.3 | ColumnagCurCfgTrapHostCommString | read-only | mandatory | The SNMP community string to use with the trap host |
| 1.3.6.1.4.1.1872.2.1.2.2.9 | TableagNewCfgTrapHostTable | not-accessible | mandatory | The table of trap hosts which to send SNMP traps in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.9.1 | RowagNewCfgTrapHostEntry | not-accessible | mandatory | A row in the trap host table in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.9.1.1 | ColumnagNewCfgTrapHostIndx | read-only | mandatory | The index of the row in trap host table. |
| 1.3.6.1.4.1.1872.2.1.2.2.9.1.2 | ColumnagNewCfgTrapHostIpAddr | read-write | mandatory | The IP address of a trap host. |
| 1.3.6.1.4.1.1872.2.1.2.2.9.1.3 | ColumnagNewCfgTrapHostCommString | read-write | mandatory | The SNMP community string to use with the trap host |
| 1.3.6.1.4.1.1872.2.1.2.2.10 | ScalaragCurCfgHttpServerPort | read-only | mandatory | The TCP port number that the HTTP server is listening to in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.11 | ScalaragNewCfgHttpServerPort | read-write | mandatory | The TCP port number that the HTTP server is listening to in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.12 | ScalaragCurCfgLoginBanner | read-only | mandatory | The user defined login banner. |
| 1.3.6.1.4.1.1872.2.1.2.2.13 | ScalaragNewCfgLoginBanner | read-write | mandatory | The user defined login banner. |
| 1.3.6.1.4.1.1872.2.1.2.2.14 | ScalaragNewCfgSyslog2Host | read-write | mandatory | The second syslog host IP address, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.15 | ScalaragCurCfgSyslog2Host | read-only | mandatory | The second syslog host IP address, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.16 | ScalaragCurCfgSyslogFac | read-only | mandatory | The facility of syslog host in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.17 | ScalaragNewCfgSyslogFac | read-write | mandatory | The facility of syslog host in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.18 | ScalaragCurCfgSyslog2Fac | read-only | mandatory | The facility of syslog2 host in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.19 | ScalaragNewCfgSyslog2Fac | read-write | mandatory | The facility of syslogs host in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.20 | ScalaragCurCfgSmtpHost | read-only | mandatory | The user defined SMTP host. |
| 1.3.6.1.4.1.1872.2.1.2.2.21 | ScalaragNewCfgSmtpHost | read-write | mandatory | The user defined SMTP host. |
| 1.3.6.1.4.1.1872.2.1.2.2.22 | ScalaragCurCfgConsole | read-only | mandatory | Enable or disable console output of syslog messages. |
| 1.3.6.1.4.1.1872.2.1.2.2.23 | ScalaragNewCfgConsole | read-write | mandatory | Enable or disable console output of syslog messages. |
| 1.3.6.1.4.1.1872.2.1.2.2.24 | ScalaragCurCfgMgmtNetwork | read-only | mandatory | The management network - corresponding to the mnet command of the slb configuration menu. |
| 1.3.6.1.4.1.1872.2.1.2.2.25 | ScalaragNewCfgMgmtNetwork | read-write | mandatory | The management network - corresponding to the mnet command of the system menu. |
| 1.3.6.1.4.1.1872.2.1.2.2.26 | ScalaragCurCfgMgmtMask | read-only | mandatory | The management subnet mask - corresponding to the mmask command of the system configuration menu. |
| 1.3.6.1.4.1.1872.2.1.2.2.27 | ScalaragNewCfgMgmtMask | read-write | mandatory | The management subnet mask - corresponding to the mmask command of the system configuration menu. |
| 1.3.6.1.4.1.1872.2.1.2.2.28 | NodeagNTP | |||
| 1.3.6.1.4.1.1872.2.1.2.2.28.1 | ScalaragCurCfgNTPServer | read-only | mandatory | The NTP Server Address. |
| 1.3.6.1.4.1.1872.2.1.2.2.28.2 | ScalaragNewCfgNTPServer | read-write | mandatory | The NTP Server Address. |
| 1.3.6.1.4.1.1872.2.1.2.2.28.3 | ScalaragCurCfgNTPResyncInterval | read-only | mandatory | The NTP Server resync interval in minutes. |
| 1.3.6.1.4.1.1872.2.1.2.2.28.4 | ScalaragNewCfgNTPResyncInterval | read-write | mandatory | The NTP Server resync interval in minutes. |
| 1.3.6.1.4.1.1872.2.1.2.2.28.5 | ScalaragCurCfgNTPTzone | read-only | mandatory | The NTP Server timezone offset from GMT in hours. |
| 1.3.6.1.4.1.1872.2.1.2.2.28.6 | ScalaragNewCfgNTPTzone | read-write | mandatory | The NTP Server timezone offset from GMT in hours. |
| 1.3.6.1.4.1.1872.2.1.2.2.28.7 | ScalaragCurCfgNTPDlight | read-only | mandatory | Enable/disable daylight savings time. |
| 1.3.6.1.4.1.1872.2.1.2.2.28.8 | ScalaragNewCfgNTPDlight | read-write | mandatory | Enable/disable daylight savings time. |
| 1.3.6.1.4.1.1872.2.1.2.2.28.9 | ScalaragCurCfgNTPService | read-only | mandatory | Enable/disable NTP Service. |
| 1.3.6.1.4.1.1872.2.1.2.2.28.10 | ScalaragNewCfgNTPService | read-write | mandatory | Enable/disable NTP Service. |
| 1.3.6.1.4.1.1872.2.1.2.2.29 | NodeagLog | |||
| 1.3.6.1.4.1.1872.2.1.2.2.29.1 | ScalaragNewCfgSyslogTrapConsole | read-write | mandatory | Enable or disable console syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.2 | ScalaragCurCfgSyslogTrapConsole | read-only | mandatory | Enable or disable console syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.3 | ScalaragNewCfgSyslogTrapSystem | read-write | mandatory | Enable or disable system level syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.4 | ScalaragCurCfgSyslogTrapSystem | read-only | mandatory | Enable or disable system level syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.5 | ScalaragNewCfgSyslogTrapMgmt | read-write | mandatory | Enable or disable management(flash, config, login) syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.6 | ScalaragCurCfgSyslogTrapMgmt | read-only | mandatory | Enable or disable management(flash, config, login) syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.7 | ScalaragNewCfgSyslogTrapCli | read-write | mandatory | Enable or disable CLI generated error syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.8 | ScalaragCurCfgSyslogTrapCli | read-only | mandatory | Enable or disable CLI generated error syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.9 | ScalaragNewCfgSyslogTrapStp | read-write | mandatory | Enable or disable spanning tree syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.10 | ScalaragCurCfgSyslogTrapStp | read-only | mandatory | Enable or disable spanning tree syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.11 | ScalaragNewCfgSyslogTrapVlan | read-write | mandatory | Enable or disable VLAN syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.12 | ScalaragCurCfgSyslogTrapVlan | read-only | mandatory | Enable or disable VLAN syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.13 | ScalaragNewCfgSyslogTrapSlb | read-write | mandatory | Enable or disable SLB syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.14 | ScalaragCurCfgSyslogTrapSlb | read-only | mandatory | Enable or disable SLB syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.15 | ScalaragNewCfgSyslogTrapGslb | read-write | mandatory | Enable or disable GSLB syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.16 | ScalaragCurCfgSyslogTrapGslb | read-only | mandatory | Enable or disable GSLB syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.17 | ScalaragNewCfgSyslogTrapFilter | read-write | mandatory | Enable or disable filter syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.18 | ScalaragCurCfgSyslogTrapFilter | read-only | mandatory | Enable or disable filter syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.19 | ScalaragNewCfgSyslogTrapSsh | read-write | mandatory | Enable or disable SSH, RADIUS syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.20 | ScalaragCurCfgSyslogTrapSsh | read-only | mandatory | Enable or disable SSH, RADIUS syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.21 | ScalaragNewCfgSyslogTrapVrrp | read-write | mandatory | Enable or disable VRRP syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.22 | ScalaragCurCfgSyslogTrapVrrp | read-only | mandatory | Enable or disable VRRP syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.23 | ScalaragNewCfgSyslogTrapBgp | read-write | mandatory | Enable or disable BGP syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.24 | ScalaragCurCfgSyslogTrapBgp | read-only | mandatory | Enable or disable BGP syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.25 | ScalaragNewCfgSyslogTrapNtp | read-write | mandatory | Enable or disable NTP syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.26 | ScalaragCurCfgSyslogTrapNtp | read-only | mandatory | Enable or disable NTP syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.27 | ScalaragNewCfgSyslogTrapIsd | read-write | mandatory | Enable or disable ISD syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.28 | ScalaragCurCfgSyslogTrapIsd | read-only | mandatory | Enable or disable ISD syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.31 | ScalaragNewCfgSyslogTrapIp | read-write | mandatory | Enable or disable IP related syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.32 | ScalaragCurCfgSyslogTrapIp | read-only | mandatory | Enable or disable IP related syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.35 | ScalaragNewCfgSyslogTrapWeb | read-write | mandatory | Enable or disable WEBUI related syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.36 | ScalaragCurCfgSyslogTrapWeb | read-only | mandatory | Enable or disable WEBUI related syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.37 | ScalaragNewCfgSyslogTrapSynAtk | read-write | mandatory | Enable or disable SYN attack detection related syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.38 | ScalaragCurCfgSyslogTrapSynAtk | read-only | mandatory | Enable or disable SYN attack detection related syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.39 | ScalaragNewCfgSyslogTrapTcpLim | read-write | mandatory | Enable or disable TCP rate limiting related syslog and SNMP trap, in the new_configuration block. |
| 1.3.6.1.4.1.1872.2.1.2.2.29.40 | ScalaragCurCfgSyslogTrapTcpLim | read-only | mandatory | Enable or disable TCP rate limiting related syslog and SNMP trap, as currently configured in the current_configuration block. |
| 1.3.6.1.4.1.1872.2.1.8 | Nodestats | |||
| 1.3.6.1.4.1.1872.2.1.8.12 | NodememStats | |||
| 1.3.6.1.4.1.1872.2.1.8.12.1 | ScalarmemStatsAllocs | read-only | mandatory | The total number of memory allocations. |
| 1.3.6.1.4.1.1872.2.1.8.12.2 | ScalarmemStatsFrees | read-only | mandatory | The total number of memory frees. |
| 1.3.6.1.4.1.1872.2.1.8.12.3 | ScalarmemStatsAllocFails | read-only | mandatory | The total number of memory allocations failed. |
| 1.3.6.1.4.1.1872.2.1.8.12.4 | ScalarmemStatsBytesCurr | read-only | mandatory | The outstanding memory in bytes have been allocated. |
| 1.3.6.1.4.1.1872.2.1.8.12.5 | ScalarmemStatsBytesHiwat | read-only | mandatory | Bytes allocated witch high water mark. |
| 1.3.6.1.4.1.1872.2.1.8.12.6 | ScalarmemStatsPoolBytes | read-only | mandatory | The total bytes in the memory pool. |
| 1.3.6.1.4.1.1872.2.1.8.12.7 | ScalarmemStatsLargest | read-only | mandatory | The largest block has been allocated. |
| 1.3.6.1.4.1.1872.2.1.8.13 | NodepktStats | |||
| 1.3.6.1.4.1.1872.2.1.8.13.1 | ScalarpktStatsAllocs | read-only | mandatory | The total packets have been allocated. |
| 1.3.6.1.4.1.1872.2.1.8.13.2 | ScalarpktStatsFrees | read-only | mandatory | The total packets have been freed. |
| 1.3.6.1.4.1.1872.2.1.8.13.3 | ScalarpktStatsAllocFails | read-only | mandatory | The total packet allocations failed. |
| 1.3.6.1.4.1.1872.2.1.8.13.4 | ScalarpktStatsMediums | read-only | mandatory | The number of medium size packets have been allocated. |
| 1.3.6.1.4.1.1872.2.1.8.13.5 | ScalarpktStatsJumbos | read-only | mandatory | The number of jumbo size packets have been allocated. |
| 1.3.6.1.4.1.1872.2.1.8.13.6 | ScalarpktStatsSmalls | read-only | mandatory | The number of small size packets have been allocated. |
| 1.3.6.1.4.1.1872.2.1.8.16 | NodempCpuStats | |||
| 1.3.6.1.4.1.1872.2.1.8.16.1 | ScalarmpCpuAStatsUtil1Second | read-only | mandatory | The utilization of MP CPU A over 1 second. It shows the percentage. |
| 1.3.6.1.4.1.1872.2.1.8.16.2 | ScalarmpCpuBStatsUtil1Second | read-only | mandatory | The utilization of MP CPU B over 4 seconds. It shows the percentage. |
| 1.3.6.1.4.1.1872.2.1.8.16.3 | ScalarmpCpuAStatsUtil4Seconds | read-only | mandatory | The utilization of MP CPU A over 4 seconds. It shows the percentage. |
| 1.3.6.1.4.1.1872.2.1.8.16.4 | ScalarmpCpuBStatsUtil4Seconds | read-only | mandatory | The utilization of MP CPU B over 4 seconds. It shows the percentage. |
| 1.3.6.1.4.1.1872.2.1.8.16.5 | ScalarmpCpuAStatsUtil64Seconds | read-only | mandatory | The utilization of MP CPU A over 64 seconds. It shows the percentage. |
| 1.3.6.1.4.1.1872.2.1.8.16.6 | ScalarmpCpuBStatsUtil64Seconds | read-only | mandatory | The utilization of MP CPU B over 64 second. It shows the percentage. |
| 1.3.6.1.4.1.1872.2.1.9 | Nodeinformation | |||
| 1.3.6.1.4.1.1872.2.1.13 | NodealtswitchTraps | |||
| 1.3.6.1.4.1.1872.2.1.14 | NodeoperCmds | |||
| 1.3.6.1.4.1.1872.2.1.16 | Noderadius | |||
| 1.3.6.1.4.1.1872.2.1.16.1 | ScalarradCurCfgPrimaryIpAddr | read-only | mandatory | The IP address of the Primary RADIUS server. |
| 1.3.6.1.4.1.1872.2.1.16.2 | ScalarradNewCfgPrimaryIpAddr | read-write | mandatory | The IP address of the Primary RADIUS server. |
| 1.3.6.1.4.1.1872.2.1.16.3 | ScalarradCurCfgSecondaryIpAddr | read-only | mandatory | The IP address of the Secondary RADIUS server. |
| 1.3.6.1.4.1.1872.2.1.16.4 | ScalarradNewCfgSecondaryIpAddr | read-write | mandatory | The IP address of the Secondary RADIUS server. |
| 1.3.6.1.4.1.1872.2.1.16.5 | ScalarradCurCfgPort | read-only | mandatory | Specify the RADIUS port number. |
| 1.3.6.1.4.1.1872.2.1.16.6 | ScalarradNewCfgPort | read-write | mandatory | Speicfy the RADIUS port number. |
| 1.3.6.1.4.1.1872.2.1.16.7 | ScalarradCurCfgTimeout | read-only | mandatory | The maximum number of seconds before resending authentication to RADIUS server. |
| 1.3.6.1.4.1.1872.2.1.16.8 | ScalarradNewCfgTimeout | read-write | mandatory | The maximum number of seconds before resending authentication to RADIUS server. |
| 1.3.6.1.4.1.1872.2.1.16.9 | ScalarradCurCfgRetries | read-only | mandatory | Number of retries to the RADIUS server. |
| 1.3.6.1.4.1.1872.2.1.16.10 | ScalarradNewCfgRetries | read-write | mandatory | Number of retries to the RADIUS server. |
| 1.3.6.1.4.1.1872.2.1.16.11 | ScalarradCurCfgState | read-only | mandatory | Enable or disbale RADIUS authentication. |
| 1.3.6.1.4.1.1872.2.1.16.12 | ScalarradNewCfgState | read-write | mandatory | Enable or disable RADIUS authentication. |
| 1.3.6.1.4.1.1872.2.1.16.13 | ScalarradCurCfgAuthenString | read-only | mandatory | The RADIUS authentication string. |
| 1.3.6.1.4.1.1872.2.1.16.14 | ScalarradNewCfgAuthenString | read-write | mandatory | The RADIUS authentication string. |
| 1.3.6.1.4.1.1872.2.1.16.15 | ScalarradCurCfgTelnet | read-only | mandatory | Enable or disbale RADIUS backdoor for telnet. |
| 1.3.6.1.4.1.1872.2.1.16.16 | ScalarradNewCfgTelnet | read-write | mandatory | Enable or disable RADIUS backdoor for telnet. |