AP80-PRIVATE-MIB
349 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC1155-SMI | Counter enterprises IpAddress mgmt |
| RFC1213-MIB | ifIndex |
| SNMPv2-SMI | Integer32 |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.14823 | Nodearuba | |||
| 1.3.6.1.4.1.14823.2 | NodearubaEnterpriseMibModules | |||
| 1.3.6.1.4.1.14823.2.3 | NodearubaAp | |||
| 1.3.6.1.4.1.14823.2.3.2 | NodewlsrOutDoorApMibModules | |||
| 1.3.6.1.4.1.14823.2.3.2.1 | NodeenterpriseApSys | |||
| 1.3.6.1.4.1.14823.2.3.2.1.1 | ScalarswHardwareVer | read-only | current | Hardware version of the main board. |
| 1.3.6.1.4.1.14823.2.3.2.1.2 | ScalarswBootRomVer | read-only | current | Boot ROM code version of the main board. |
| 1.3.6.1.4.1.14823.2.3.2.1.3 | ScalarswOpCodeVer | read-only | current | Operation code version of the main board. |
| 1.3.6.1.4.1.14823.2.3.2.1.4 | ScalarswSerialNumber | read-only | current | Serial Number of the Access Point. |
| 1.3.6.1.4.1.14823.2.3.2.1.5 | NodesysNotificationTree | |||
| 1.3.6.1.4.1.14823.2.3.2.1.5.1 | NodesysNotificationObjects | |||
| 1.3.6.1.4.1.14823.2.3.2.1.5.2 | NodesysNotifications | |||
| 1.3.6.1.4.1.14823.2.3.2.1.5.2.1 | NotificationsysSystemUp | current | The system up notification shall be sent when the AP is fully up and running. | |
| 1.3.6.1.4.1.14823.2.3.2.1.5.2.2 | NotificationsysSystemDown | current | The system down notification shall be sent before the AP is about to reboot. | |
| 1.3.6.1.4.1.14823.2.3.2.1.5.2.3 | NotificationsysRadiusServerChanged | current | The RADIUS server changed notification shall be sent when the RADIUS server has changed from Primary / Secondary to Secondary / Primary. | |
| 1.3.6.1.4.1.14823.2.3.2.1.5.2.4 | NotificationsysConfigFileVersionChanged | current | The Config file version changed notification shall be sent when the version of the AP's configuration file has changed. | |
| 1.3.6.1.4.1.14823.2.3.2.2 | NodeenterpriseApLineMgnt | |||
| 1.3.6.1.4.1.14823.2.3.2.2.1 | TablelineTable | not-accessible | current | Table of descriptive and status information about configuration of each RS-232 line in this system |
| 1.3.6.1.4.1.14823.2.3.2.2.1.1 | RowlineEntry | not-accessible | current | An entry in the table, containing information about configuration in one RS232 line of the Access Point. |
| 1.3.6.1.4.1.14823.2.3.2.2.1.1.1 | ColumnlineIndex | not-accessible | current | This is defined as RS-232 index. |
| 1.3.6.1.4.1.14823.2.3.2.2.1.1.2 | ColumnlineDataBits | read-only | current | This is defined as number of data bits for the RS232 interface. |
| 1.3.6.1.4.1.14823.2.3.2.2.1.1.3 | ColumnlineParity | read-only | current | This is defined as parity of the RS232 interface. |
| 1.3.6.1.4.1.14823.2.3.2.2.1.1.4 | ColumnlineSpeed | read-only | current | This is defined as the speed of the RS-232 interface. |
| 1.3.6.1.4.1.14823.2.3.2.2.1.1.5 | ColumnlineStopBits | read-only | current | This is defined as the number of stop bits for the RS-232 interface. |
| 1.3.6.1.4.1.14823.2.3.2.3 | NodeenterpriseApPortMgnt | |||
| 1.3.6.1.4.1.14823.2.3.2.3.1 | TableportTable | not-accessible | current | Table of descriptive and status information about configuration of each switch port (including expansion slot) in this system. This table also contains informa… |
| 1.3.6.1.4.1.14823.2.3.2.3.1.1 | RowportEntry | not-accessible | current | An entry in the table, containing information about configuration in one switch port of the switch. |
| 1.3.6.1.4.1.14823.2.3.2.3.1.1.1 | ColumnportIndex | not-accessible | current | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.14823.2.3.2.3.1.1.2 | ColumnportName | read-only | current | Indicates the port name. This is same as ifAlias in the IF-MIB (RFC2863 or later). |
| 1.3.6.1.4.1.14823.2.3.2.3.1.1.3 | ColumnportType | read-only | current | Indicates the port type. |
| 1.3.6.1.4.1.14823.2.3.2.3.1.1.4 | ColumnportSpeedDpxCfg | read-only | current | Indicates the port speed and duplex mode as follows: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(… |
| 1.3.6.1.4.1.14823.2.3.2.3.1.1.5 | ColumnportFlowCtrlCfg | read-only | current | (1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPr… |
| 1.3.6.1.4.1.14823.2.3.2.3.1.1.6 | ColumnportCapabilities | read-only | current | Port capabilities. |
| 1.3.6.1.4.1.14823.2.3.2.3.1.1.7 | ColumnportAutonegotiation | read-only | current | Whether autonegotiation is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.3.1.1.8 | ColumnportSpeedDpxStatus | read-only | current | The operating speed and duplex mode of the switched port. If this index is a trunk, the speed is the speed of its individual members. If this index is a trunk … |
| 1.3.6.1.4.1.14823.2.3.2.3.1.1.9 | ColumnportFlowCtrlStatus | read-only | current | (2) BackPressure flow control machanism is used. (3) IEEE 802.3 flow control machanism is used. (4) Flow control mechanism is disabled. If this index is a trun… |
| 1.3.6.1.4.1.14823.2.3.2.4 | NodeenterpriseApFileTransferMgt | |||
| 1.3.6.1.4.1.14823.2.3.2.4.1 | ScalartransferType | read-write | current | Type of file to transfer. |
| 1.3.6.1.4.1.14823.2.3.2.4.2 | ScalarfileType | read-write | current | Type of file to transfer. |
| 1.3.6.1.4.1.14823.2.3.2.4.3 | ScalarsrcFile | read-write | current | The source file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has been s… |
| 1.3.6.1.4.1.14823.2.3.2.4.4 | ScalardestFile | read-write | current | The destination file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has b… |
| 1.3.6.1.4.1.14823.2.3.2.4.5 | ScalarfileServer | read-write | current | The IP address of the TFTP server for transfer when a download is next requested via this MIB. This value is set to `0.0.0.0' when no IP address has been speci… |
| 1.3.6.1.4.1.14823.2.3.2.4.6 | ScalaruserName | read-write | current | The username specified for an FTP Transfer. |
| 1.3.6.1.4.1.14823.2.3.2.4.7 | Scalarpassword | read-write | current | The password specified for an FTP Transfer. |
| 1.3.6.1.4.1.14823.2.3.2.4.8 | Scalarstatus | read-only | current | The status of the transfer. |
| 1.3.6.1.4.1.14823.2.3.2.4.9 | ScalartransferStart | read-write | current | Set to go(1) to start a transfer. |
| 1.3.6.1.4.1.14823.2.3.2.5 | NodeenterpriseApResetMgt | |||
| 1.3.6.1.4.1.14823.2.3.2.5.1 | ScalarrestartOpCodeFile | read-write | current | Name of op-code file for start-up. |
| 1.3.6.1.4.1.14823.2.3.2.5.2 | ScalarrestartControl | read-write | current | Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Se… |
| 1.3.6.1.4.1.14823.2.3.2.6 | NodeenterpriseApIpMgt | |||
| 1.3.6.1.4.1.14823.2.3.2.6.1 | ScalarnetConfigIPAddress | read-write | current | The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then w… |
| 1.3.6.1.4.1.14823.2.3.2.6.2 | ScalarnetConfigSubnetMask | read-write | current | The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then … |
| 1.3.6.1.4.1.14823.2.3.2.6.3 | ScalarnetConfigDefaultGateway | read-write | current | The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0. |
| 1.3.6.1.4.1.14823.2.3.2.6.4 | ScalarnetConfigHttpState | read-write | current | Whether HTTP is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.6.5 | ScalarnetConfigHttpPort | read-write | current | The port number for HTTP. Default port number is 80. |
| 1.3.6.1.4.1.14823.2.3.2.6.6 | ScalarnetConfigHttpsState | read-write | current | Whether Secure HTTP is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.6.7 | ScalarnetConfigHttpsPort | read-write | current | The port number for Secure HTTP. Default port number is 443. |
| 1.3.6.1.4.1.14823.2.3.2.6.8 | ScalarnetConfigDHCPState | read-write | current | Whether DHCP is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.7 | NodeenterpriseAPdot11 | |||
| 1.3.6.1.4.1.14823.2.3.2.7.1 | Nodedot11AuthenticationEntry | |||
| 1.3.6.1.4.1.14823.2.3.2.7.1.1 | Scalardot118021xState | read-write | obsolete | This attribute indicates that the Enterprise the state of the 802.1x authentication algorithm. |
| 1.3.6.1.4.1.14823.2.3.2.7.1.2 | Scalardot118021xBroadcastKeyRefreshRate | read-write | obsolete | The number (in minutes) between changing the broadcast key for 802.1x and WPA clients |
| 1.3.6.1.4.1.14823.2.3.2.7.1.3 | Scalardot118021xSessionKeyRefreshRate | read-write | obsolete | The number (in minutes) between changing session keys for 802.1x and WPA clients |
| 1.3.6.1.4.1.14823.2.3.2.7.1.4 | Scalardot118021xReauthenticationTimeout | read-write | obsolete | The number (in minutes) between forcing 802.1x clients to reauthenticate |
| 1.3.6.1.4.1.14823.2.3.2.7.1.5 | Scalardot11MACAuthenticationType | read-write | obsolete | This value indicates the type of mac authentication in use. |
| 1.3.6.1.4.1.14823.2.3.2.7.2 | Tabledot11AuthenticationServerTable | not-accessible | current | Table of descriptive and status information about configuration of each authentication server. |
| 1.3.6.1.4.1.14823.2.3.2.7.2.1 | Rowdot11AuthenticationServerEntry | not-accessible | current | An entry in the table, containing information about configuration of one authentication server of the AP. |
| 1.3.6.1.4.1.14823.2.3.2.7.2.1.1 | Columndot11AuthenticationServerIndex | not-accessible | current | Index of the Authentication Server |
| 1.3.6.1.4.1.14823.2.3.2.7.2.1.2 | Columndot11AuthenticationServer | read-write | current | This value indicates the IP address of the authentication server. |
| 1.3.6.1.4.1.14823.2.3.2.7.2.1.3 | Columndot11AuthenticationPort | read-write | current | This value indicates the UDP Port used by the authentication server. |
| 1.3.6.1.4.1.14823.2.3.2.7.2.1.4 | Columndot11AuthenticationKey | read-write | current | This value indicates the shared key used by the authentication server. |
| 1.3.6.1.4.1.14823.2.3.2.7.2.1.5 | Columndot11AuthenticationRetransmit | read-write | current | This value indicates the retransmit timer length used by the authentication server. |
| 1.3.6.1.4.1.14823.2.3.2.7.2.1.6 | Columndot11AuthenticationTimeout | read-write | current | This value indicates the Timeout value(sec) used by the authentication server. |
| 1.3.6.1.4.1.14823.2.3.2.7.2.1.7 | Columndot11AuthenticationAcctPort | read-write | current | The port number for radius server accounting. |
| 1.3.6.1.4.1.14823.2.3.2.7.2.1.8 | Columndot11AuthenticationAcctInterimUpdate | read-write | current | This value indicates the Timeout value(sec) used by the radius server interim update. |
| 1.3.6.1.4.1.14823.2.3.2.7.2.1.9 | Columndot11AuthenticationMACAddressFormat | read-write | current | This value indicates the MAC address format from Radius MAC authentication. no-delimiter format: aabbccddeeff single-dash format: aabbcc-ddeeff multi-dash form… |
| 1.3.6.1.4.1.14823.2.3.2.7.2.1.10 | Columndot11AuthenticationVLANIDFormat | read-write | current | This value indicates the VLAN ID format from Radius server. |
| 1.3.6.1.4.1.14823.2.3.2.7.3 | Nodedot11MACAuthenticationFilter | |||
| 1.3.6.1.4.1.14823.2.3.2.7.3.1 | Scalardot11FilterDefault | read-write | current | This value indicates the default access for local mac filters. |
| 1.3.6.1.4.1.14823.2.3.2.7.3.2 | Tabledot11FilterTable | not-accessible | current | Table of status information about each configured MAC Address Filtering Entry. |
| 1.3.6.1.4.1.14823.2.3.2.7.3.2.1 | Rowdot11FilterEntry | not-accessible | current | An entry in the table, containing information about configuration in one radio of the AP. |
| 1.3.6.1.4.1.14823.2.3.2.7.3.2.1.1 | Columndot11FilterAddress | not-accessible | current | This value indicates the MAC address of the filter entry. |
| 1.3.6.1.4.1.14823.2.3.2.7.3.2.1.2 | Columndot11FilterStatus | read-write | current | This value indicates the Status of the filter entry. Ifallowed, the client is allowed access to the network. If disallowed, the no frames will be forwarded to … |
| 1.3.6.1.4.1.14823.2.3.2.7.4 | Nodedot11NotificationTree | |||
| 1.3.6.1.4.1.14823.2.3.2.7.4.1 | Nodedot11NotificationObjects | |||
| 1.3.6.1.4.1.14823.2.3.2.7.4.1.1 | Scalardot11MacAddr | not-accessible | current | Mac Address of the affected interface, returned with traps only. |
| 1.3.6.1.4.1.14823.2.3.2.7.4.1.2 | Scalardot11Station | not-accessible | current | This attribute holds the MAC address of the wireless station |
| 1.3.6.1.4.1.14823.2.3.2.7.4.1.3 | Scalardot11RequestType | not-accessible | current | This attribute defines the request type sent by the station. Value = 1: Unknown request type Value = 2: Association Request Value = 3: Re-association Request V… |
| 1.3.6.1.4.1.14823.2.3.2.7.4.1.4 | Scalardot11ReasonCode | not-accessible | current | This attribute defines the reason for the failure of an operation. Value = 1: Invalid mode/state Value = 2: Station not authenticated. Value = 3: Internal erro… |
| 1.3.6.1.4.1.14823.2.3.2.7.4.1.5 | Scalardot11ApIpAddress | not-accessible | current | This value indicates the IP address of the Access Point |
| 1.3.6.1.4.1.14823.2.3.2.7.4.1.6 | Scalardot1xAuthenticatorMacAddr | not-accessible | current | This attribute holds the MAC address of the authenticator for the AP. |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2 | Nodedot11Notifications | |||
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.1 | Notificationdot11StationAssociation | current | The associate notification shall be sent when a station successfully associates with the Access Point. The value of the notification shall include the MAC addr… | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.2 | Notificationdot11StationReAssociation | current | The re-associate notification shall be sent when a station successfully re-associates with the Access Point. The value of the notification shall include the MA… | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.3 | Notificationdot11StationAuthentication | current | The authentication notification shall be sent when a station successfully authenticates with the Access Point. The value of the notification shall include the … | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.4 | Notificationdot11StationRequestFail | current | The station request fail shall be sent out when a station fails to associate / re-associate / authenticate with the Access Point. The notification shall includ… | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.5 | Notificationdot11InterfaceBFail | current | The InterfaceBFail notification shall be sent out when 802.11b wireless interface has failed. | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.6 | Notificationdot11InterfaceAGFail | current | The InterfaceAGFail notification shall be sent out when 802.11a/802.11g wireless interface has failed. | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.7 | Notificationdot1xMacAddrAuthSuccess | current | The 802.1x MAC address authentication success notification shall be sent when a station successfully authenticates the MAC address with the RADIUS server. The … | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.8 | Notificationdot1xMacAddrAuthFail | current | The 802.1x MAC address authentication failure notification shall be sent when a station fails to authenticate the MAC address with the RADIUS server. The value… | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.9 | Notificationdot1xAuthNotInitiated | current | The 802.1x authentication not initiated notification shall be sent when a station did not initiate 802.1x authentication with the RADIUS server. The value of t… | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.10 | Notificationdot1xAuthSuccess | current | The 802.1x authentication success notification shall be sent when a station successfully authenticates with the RADIUS server. The value of the notification sh… | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.11 | Notificationdot1xAuthFail | current | The 802.1x authentication failure notification shall be sent when a station fails to authenticate with the RADIUS server. The value of the notification shall i… | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.12 | NotificationlocalMacAddrAuthSuccess | current | The Local MAC address authentication success notification shall be sent when a station successfully authenticates the MAC address with the database stored loca… | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.13 | NotificationlocalMacAddrAuthFail | current | The Local MAC address authentication failure notification shall be sent when a station fails to authenticate the MAC address with the database stored locally w… | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.14 | NotificationpppLogonFail | current | The PPP Logon failure notification shall be sent out when the AP fails to login successfully to the PPP peer using the supplied username and password. | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.15 | NotificationiappStationRoamedFrom | current | The IAPP Station Roamed-From Notification shall be sent out whenever a station roams from another Access Point (AP) to this AP. The notification shall include … | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.16 | NotificationiappStationRoamedTo | current | The IAPP Station Roamed-To Notification shall be sent out whenever a station roams to another Access Point (AP) from this AP. The notification shall include th… | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.17 | NotificationiappContextDataSent | current | The IAPP Context Data Sent notification shall be sent out whenever the context data for a station has been sent to the new AP with which the station has associ… | |
| 1.3.6.1.4.1.14823.2.3.2.7.4.2.18 | Notificationdot1xSupplicantAuthenticated | current | The notification shall be sent when the AP has successfully authenticated with the switch. The value of the notification shall include the MAC address of the s… | |
| 1.3.6.1.4.1.14823.2.3.2.7.5 | Tabledot11AuthenticationSupplicantTable | not-accessible | current | Table of descriptive and status information about configuration of supplicant |
| 1.3.6.1.4.1.14823.2.3.2.7.5.1 | Rowdot11AuthenticationSupplicantEntry | not-accessible | current | An entry in the table, containing information about configuration of one supplicant. |
| 1.3.6.1.4.1.14823.2.3.2.7.5.1.1 | Columndot118021xSuppIndex | not-accessible | current | Index of the interface for which this supplicant is running. Currently only the ethernet interface. |
| 1.3.6.1.4.1.14823.2.3.2.7.5.1.2 | Columndot118021xSuppState | read-write | current | This object is used to enable or disable the 802.1x supplicant. |
| 1.3.6.1.4.1.14823.2.3.2.7.5.1.3 | Columndot118021xSuppUser | read-write | current | This value indicates the username for supplicant. If value is configured, will display ****. Else will display EMPTY. |
| 1.3.6.1.4.1.14823.2.3.2.7.5.1.4 | Columndot118021xSuppPasswd | read-write | current | This value indicates the password for supplicant. If value is configured, will display ****. Else will display EMPTY. |
| 1.3.6.1.4.1.14823.2.3.2.7.6 | Tabledot11VapAuthenticationTable | not-accessible | current | Table of descriptive and status information about configuration of 8021x for each Vap. |
| 1.3.6.1.4.1.14823.2.3.2.7.6.1 | Rowdot11VapAuthenticationEntry | not-accessible | current | An entry in the table, containing information about configuration of 8021x for each Vap of the AP. |
| 1.3.6.1.4.1.14823.2.3.2.7.6.1.1 | Columndot11Vap8021xIndex | not-accessible | current | Index for configuration. |
| 1.3.6.1.4.1.14823.2.3.2.7.6.1.2 | Columndot11Vap8021xState | read-write | current | This attribute indicates that the Enterprise the state of the 802.1x authentication algorithm. |
| 1.3.6.1.4.1.14823.2.3.2.7.6.1.3 | Columndot11Vap8021xBroadcastKeyRefreshRate | read-write | current | The number (in minutes) between changing the broadcast key for 802.1x and WPA clients |
| 1.3.6.1.4.1.14823.2.3.2.7.6.1.4 | Columndot11Vap8021xSessionKeyRefreshRate | read-write | current | The number (in minutes) between changing session keys for 802.1x and WPA clients |
| 1.3.6.1.4.1.14823.2.3.2.7.6.1.5 | Columndot11Vap8021xReauthenticationTimeout | read-write | current | The number (in minutes) between forcing 802.1x clients to reauthenticate |
| 1.3.6.1.4.1.14823.2.3.2.7.6.1.6 | Columndot11VapAuthMACAuthenticationType | read-write | current | This value indicates the type of mac authentication in use. |
| 1.3.6.1.4.1.14823.2.3.2.7.6.1.7 | Columndot11VapAuthMACAuthenticationTimeout | read-write | current | The number (in minutes) between forcing Radius MAC to authenticate. |
| 1.3.6.1.4.1.14823.2.3.2.8 | NodeenterpriseApAdmin | |||
| 1.3.6.1.4.1.14823.2.3.2.8.1 | ScalarenterpriseApAdminUser | read-write | current | This value indicates the username for management login. |
| 1.3.6.1.4.1.14823.2.3.2.8.2 | ScalarenterpriseApAdminPassword | read-write | current | This value indicates the password for management login. The password length is betwen 3 and 16. 'Zero-length' indicates 'no password'. |
| 1.3.6.1.4.1.14823.2.3.2.9 | NodeenterpriseApVLAN | |||
| 1.3.6.1.4.1.14823.2.3.2.9.1 | ScalarenterpriseApVLANNativeId | read-write | current | This value indicates the native VLAN id. |
| 1.3.6.1.4.1.14823.2.3.2.9.2 | ScalarenterpriseApVLANState | read-write | current | This value indicates whether VLANs are enabled or disabled. |
| 1.3.6.1.4.1.14823.2.3.2.9.3 | TableenterpriseApNativeVlanTable | not-accessible | mandatory | Table used to manage the Vlans for each wireless interface. |
| 1.3.6.1.4.1.14823.2.3.2.9.3.1 | RowenterpriseApNativeVlanEntry | not-accessible | mandatory | An entry in the table, containing information about vlan configuration of one wireless interface. |
| 1.3.6.1.4.1.14823.2.3.2.9.3.1.1 | ColumnnativeVlanIfIndex | not-accessible | mandatory | Interface Index of the wireless interface for which the vlan is assigned to. |
| 1.3.6.1.4.1.14823.2.3.2.9.3.1.2 | ColumnnativeVlanSsidNumber | not-accessible | mandatory | Associated Number for Service Set Id (SSID) of the wireless interface for which the vlan is assigned to. Note: This is for future support of multiple SSIDs per… |
| 1.3.6.1.4.1.14823.2.3.2.9.3.1.3 | ColumnnativeVlanVlanId | read-write | mandatory | This value indicates the native VLAN id of the wireless interface associated with the if index and the SSID number(if it is not 0). |
| 1.3.6.1.4.1.14823.2.3.2.10 | NodeenterpriseApFilterControl | |||
| 1.3.6.1.4.1.14823.2.3.2.10.1 | ScalarenterpriseApFilterControlInterClientSTAsCommun | read-write | current | This value indicates the Inter Client STAs Communication Filter setting. disabled (1) To disable the Inter Client STAs Communication Filter PreventIntraVAPClie… |
| 1.3.6.1.4.1.14823.2.3.2.10.2 | ScalarenterpriseApFilterControlAPManage | read-write | current | This value indicates the AP management filter setting. |
| 1.3.6.1.4.1.14823.2.3.2.10.3 | ScalarenterpriseApFilterControlEthernet | read-write | current | This value indicates the ethernet filter setting. |
| 1.3.6.1.4.1.14823.2.3.2.10.4 | TableenterpriseApFilterProtocolTable | not-accessible | current | Table of descriptive and status information about configuration of the filter protocol table. |
| 1.3.6.1.4.1.14823.2.3.2.10.4.1 | RowenterpriseApFilterProtocolEntry | not-accessible | current | An entry in the filter protocol table, containing information about configuration of one filter table entry. |
| 1.3.6.1.4.1.14823.2.3.2.10.4.1.1 | ColumnenterpriseApFilterProtocolIndex | not-accessible | current | Index of the Protocol Filters. |
| 1.3.6.1.4.1.14823.2.3.2.10.4.1.2 | ColumnenterpriseApFilterProtocolName | read-only | current | This value indicates the name of the protocol filter. One of the following: Aironet_DDP, Appletalk_ARP, ARP, Banyan, Berkeley_Trailer_Negotiation, CDP, DEC_LAT… |
| 1.3.6.1.4.1.14823.2.3.2.10.4.1.3 | ColumnenterpriseApFilterProtocolISODesignator | read-only | current | This value indicates the name of the protocol filter. |
| 1.3.6.1.4.1.14823.2.3.2.10.4.1.4 | ColumnenterpriseApFilterProtocolState | read-write | current | This value indicates whether the protocol filter is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.10.5 | NodeenterpriseApFilterUplinkPortMACAddrFilter | |||
| 1.3.6.1.4.1.14823.2.3.2.10.5.1 | ScalaruplinkPortMACAddrFilterStatus | read-write | current | This value indicates whether the Uplink Port MAC Address Filter Table is enabled or not. |
| 1.3.6.1.4.1.14823.2.3.2.10.5.2 | ScalaruplinkPortMACAddrFilterAddMac | read-write | current | To add mac address to Uplink Port MAC Address Filter Table. (Mac Address format: xx-xx-xx-xx-xx-xx or xx:xx:xx:xx:xx:xx) |
| 1.3.6.1.4.1.14823.2.3.2.10.5.3 | TableuplinkPortMACAddrFilteringTable | not-accessible | current | Table of descriptive and status information about configuration of the Uplink Port MAC Address Filter Table. |
| 1.3.6.1.4.1.14823.2.3.2.10.5.3.1 | RowuplinkPortMACAddrFilteringEntry | not-accessible | current | An entry in Uplink Port MAC Address Filter Table. |
| 1.3.6.1.4.1.14823.2.3.2.10.5.3.1.1 | ColumnuplinkPortMacAddrIndex | read-only | current | The index for Uplink Port MAC Address Filter Table. |
| 1.3.6.1.4.1.14823.2.3.2.10.5.3.1.2 | ColumnuplinkPortMACAddr | read-only | current | The MAC Address of wireless clients which allowed to communicate on subnet. |
| 1.3.6.1.4.1.14823.2.3.2.10.5.3.1.3 | ColumndeleteMacAddr | read-write | current | To delete the MAC Address from Uplink Port MAC Address Filter Table. Delete(1) To start delete MAC address. Nothing(2) Nothing occur. |
| 1.3.6.1.4.1.14823.2.3.2.11 | NodeenterpriseApSNTP | |||
| 1.3.6.1.4.1.14823.2.3.2.11.1 | ScalarenterpriseApSNTPState | read-write | current | This value indicates whether SNTP is enabled or not. At least one of the SNTP servers must have a valid IP address before SNTP can be enabled. |
| 1.3.6.1.4.1.14823.2.3.2.11.2 | ScalarenterpriseApSNTPPrimaryServer | read-write | current | This value indicates the IP address of the primary SNTP server. |
| 1.3.6.1.4.1.14823.2.3.2.11.3 | ScalarenterpriseApSNTPSecondaryServer | read-write | current | This value indicates the IP address of the secondary SNTP server. |
| 1.3.6.1.4.1.14823.2.3.2.11.4 | ScalarenterpriseApSNTPTimezone | read-write | current | This value indicates which timezone to use. |
| 1.3.6.1.4.1.14823.2.3.2.11.5 | ScalarenterpriseApSNTPDST | read-write | current | This value indicates whether Daylight Savings Time is enabled or not. |
| 1.3.6.1.4.1.14823.2.3.2.11.6 | ScalarenterpriseApSNTPDSTStartMonth | read-write | current | This value indicates the starting month for Daylight Savings Time. |
| 1.3.6.1.4.1.14823.2.3.2.11.7 | ScalarenterpriseApSNTPDSTStartDay | read-write | current | This value indicates the starting day for Daylight Savings Time. |
| 1.3.6.1.4.1.14823.2.3.2.11.8 | ScalarenterpriseApSNTPDSTEndMonth | read-write | current | This value indicates the ending month for Daylight Savings Time. |
| 1.3.6.1.4.1.14823.2.3.2.11.9 | ScalarenterpriseApSNTPDSTEndDay | read-write | current | This value indicates the ending day for Daylight Savings Time. |
| 1.3.6.1.4.1.14823.2.3.2.11.10 | NodesntpNotificationTree | |||
| 1.3.6.1.4.1.14823.2.3.2.11.10.1 | NodesntpNotificationObjects | |||
| 1.3.6.1.4.1.14823.2.3.2.11.10.2 | NodesntpNotifications | |||
| 1.3.6.1.4.1.14823.2.3.2.11.10.2.1 | NotificationsntpServerFail | current | The sntpServerFail notification shall be sent when the AP fails to get time from the configured SNTP server. | |
| 1.3.6.1.4.1.14823.2.3.2.12 | NodeenterpriseApDNS | |||
| 1.3.6.1.4.1.14823.2.3.2.12.1 | ScalarenterpriseApDNSPrimaryServer | read-write | current | This value indicates the IP address of the primary DNS server. |
| 1.3.6.1.4.1.14823.2.3.2.12.2 | ScalarenterpriseApDNSSecondaryServer | read-write | current | This value indicates the IP address of the secondary DNS server. |
| 1.3.6.1.4.1.14823.2.3.2.13 | NodeenterpriseApSyslog | |||
| 1.3.6.1.4.1.14823.2.3.2.13.1 | ScalarenterpriseApSyslogState | read-write | current | This value indicates whether syslog is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.13.2 | ScalarenterpriseApSyslogConsoleState | read-write | current | This value indicates whether syslog console logging is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.13.3 | ScalarenterpriseApSyslogLevel | read-write | current | This value indicates the syslog logging level. |
| 1.3.6.1.4.1.14823.2.3.2.13.4 | TableenterpriseApSyslogServerTable | not-accessible | current | Table of descriptive and status information about configuration of each syslog server. |
| 1.3.6.1.4.1.14823.2.3.2.13.4.1 | RowenterpriseApSyslogServerEntry | not-accessible | current | An entry in the table, containing information about configuration of one syslog server of the AP. |
| 1.3.6.1.4.1.14823.2.3.2.13.4.1.1 | ColumnenterpriseApSyslogServerIndex | not-accessible | current | Index of the Syslog Server |
| 1.3.6.1.4.1.14823.2.3.2.13.4.1.2 | ColumnenterpriseApSyslogServerState | read-write | current | This value indicates whether the syslog server is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.13.4.1.3 | ColumnenterpriseApSyslogServerIPAddress | read-write | current | This value indicates the IP address of the syslog server. |
| 1.3.6.1.4.1.14823.2.3.2.13.4.1.4 | ColumnenterpriseApSyslogServerPort | read-write | current | This value indicates the UDP Port used by the syslog server. |
| 1.3.6.1.4.1.14823.2.3.2.14 | NodeenterpriseApSecurity | |||
| 1.3.6.1.4.1.14823.2.3.2.14.1 | TableenterpriseApSecurityTable | not-accessible | current | Table of descriptive and status information about configuration of each radio in terms of security settings. |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1 | RowenterpriseApSecurityEntry | not-accessible | current | An entry in the table, containing information about configuration of one radio of the AP. |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1.1 | ColumnenterpriseApSecurityIndex | not-accessible | current | Radio Index for security settings. |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1.2 | ColumnenterpriseApSecurityAuthType | read-write | current | This value indicates the type of authentication in use for this radio interface. opensystem(0) Set authentication open sharedkey(1) Set authentication shared w… |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1.3 | ColumnenterpriseApSecuritySharedKeyLen | read-only | current | This value indicates the shared key length for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1.4 | ColumnenterpriseApSecurityWPAMode | read-write | current | This value indicates the state of WPA for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1.5 | ColumnenterpriseApSecurityWPAKeyType | read-write | current | This value indicates the type of WPA Key Management in use for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1.6 | ColumnenterpriseApSecurityWPACipher | read-write | obsolete | This value indicates the type of WPA Cipher in use for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1.7 | ColumnenterpriseApSecurityWPAPSKType | read-write | current | This value indicates the type of WPA Pre Shared Key in use for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1.8 | ColumnenterpriseApSecurityWPAPSK | read-write | current | This value indicates WPA Pre Shared Key in use for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1.9 | ColumnenterpriseApSecurityWEPKeyType | read-write | current | This value indicates the type of WEP Key in use for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1.10 | ColumnenterpriseApSecurityWEPEnabled | read-write | current | This value indicates whether WEP is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1.11 | ColumnenterpriseApSecurityWPACipherSuite | read-write | current | This value indicates the type of WPA Cipher Suite in use for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1.12 | ColumnenterpriseApSecurityWPAPreAuthentication | read-write | current | Whether Pre-Authentication is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.14.1.1.13 | ColumnenterpriseApSecurityWPAPmksaLifetime | read-write | current | The number (in minutes) for Pmksa-Lifetime. |
| 1.3.6.1.4.1.14823.2.3.2.14.2 | NodeenterpriseApSsh | |||
| 1.3.6.1.4.1.14823.2.3.2.14.2.1 | ScalarenterpriseApSshServerEnabled | read-write | mandatory | This value indicates whether SSH server is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.14.2.2 | ScalarenterpriseApSshServerPort | read-write | mandatory | This value indicates SSH server's port number. |
| 1.3.6.1.4.1.14823.2.3.2.14.2.3 | ScalarenterpriseApSshTelnetServerEnabled | read-write | mandatory | This value indicates whether telnet server is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.15 | NodeenterpriseApRadio | |||
| 1.3.6.1.4.1.14823.2.3.2.15.1 | TableenterpriseApRadioTable | not-accessible | current | Table of descriptive and status information about configuration of each radio. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1 | RowenterpriseApRadioEntry | not-accessible | current | An entry in the table, containing information about configuration of one radio of the AP. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.1 | ColumnenterpriseApRadioIndex | not-accessible | current | Radio Index for configuration. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.2 | ColumnenterpriseApRadioState | read-write | obsolete | This value indicates the state of the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.3 | ColumnenterpriseApRadioAutoChannel | read-write | current | This value indicates whether auto channel selection is enabled or not for this radio interface |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.4 | ColumnenterpriseApRadioTransmitPower | read-write | current | This value indicates the transmit power for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.5 | ColumnenterpriseApRadioClosedSystem | read-write | obsolete | This value indicates whether closed system is enabled for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.6 | ColumnenterpriseApRadioMaxAssoc | read-write | obsolete | This value indicates the max number of clients allowed on this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.7 | ColumnenterpriseApRadioTransmitKey | read-write | obsolete | This value indicates default transmit key in use for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.8 | ColumnenterpriseApRadioTurboMode | read-write | current | This value indicates whether turbo mode is enabled for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.9 | ColumnenterpriseApRadioDescription | read-write | obsolete | This value indicates the description for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.10 | ColumnenterpriseApRadioDataRate | read-write | current | This value indicates the data rate for this radio interface. Radio interface A operates at 6, 9, 12, 18, 24, 36, 48, 54. Radio interface G operates all listed … |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.11 | ColumnenterpriseApRadioGMode | read-write | current | This value indicates the radio mode for the 802.11g radio. This setting is only valid for the 802.11g interface. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.12 | ColumnenterpriseApRadioAntennaMode | read-write | mandatory | This value indicates the antenna mode in use for the G-radio. The values are interpreted as follows: fixed(1) means use both built-in antennas, external(2) mea… |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.13 | ColumnenterpriseApRadioAntennaId | read-only | current | |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.14 | ColumnenterpriseApRadioAntennaControlMethod | read-write | current | This value indicates the antenna control method for the radio index. Diversity(1) AP select the antenna automatically. Left (2) Use the left antenna. Right (3)… |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.15 | ColumnenterpriseApRadioAntennaLocation | read-write | current | This value indicates the location of antenna for each radio index. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.16 | ColumnenterpriseApRadioRogueApDetection | read-write | current | The status of Rogue AP detection for each index. enabled(1) To set rogue Ap detection enabled. disabled(2) To set rogue Ap detection disabled. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.17 | ColumnenterpriseApRadioRogueApScanInterval | read-write | current | This value indicates the interval between each rogue AP scan.(unit: minutes) |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.18 | ColumnenterpriseApRadioRogueApScanDuration | read-write | current | This value indicates the rogue AP scan duratoin.(unit: minutes) |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.19 | ColumnenterpriseApRadioRogueApScanNow | read-write | current | To force Ap to do rogue AP scan right away. enabled(1) To do Rogue AP scan right now. disabled(2) To set rogue Ap. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.21 | ColumnenterpriseApRadioMICMode | read-write | current | This value indicates the MIC mode status for this radio index. software(1) To set MIC mode to software. hardware(2) To set MIC mode to hardware. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.22 | ColumnenterpriseApRadioSuperMode | read-write | current | This value indicates the super mode status for this radio index. enabled (1) To set super mode enabled. disabled(2) To set super mode disabled. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.23 | ColumnenterpriseApRadioBeaconInterval | read-write | current | This value indicates the beacon interval for this radio index. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.24 | ColumnenterpriseApRadioDataBeaconRate | read-write | current | This value indicates the data beacon rate for the radio index. |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.25 | ColumnenterpriseApRadioChannel | read-write | current | This valud indicates the radio channel for the radio index. set channel 42/50/58/152/160 for static turbo mode, set channel 40/48/56/153/161 for dynamic turbo … |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.26 | ColumnenterpriseApRadioFragmentLength | read-write | current | This value indicates the fragment length for the radio index.(unit: Byte) |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.27 | ColumnenterpriseApRadioRTSThreshold | read-write | current | This value indicates the RTS Threshold for the radio index.(unit: Byte) |
| 1.3.6.1.4.1.14823.2.3.2.15.1.1.28 | ColumnenterpriseApRadioAntennaGainReduction | read-write | current | This value indicates the antenna gain reduction for the radio index.(unit: dB) |
| 1.3.6.1.4.1.14823.2.3.2.16 | NodeenterpriseApSNMP | |||
| 1.3.6.1.4.1.14823.2.3.2.16.1 | ScalarenterpriseApSNMPCommunityReadOnly | read-write | current | The SNMP Read Only Community. The value if read, will only show ******. |
| 1.3.6.1.4.1.14823.2.3.2.16.2 | ScalarenterpriseApSNMPCommunityReadWrite | read-write | current | The SNMP Read Write Community. The value if read, will only show *****. |
| 1.3.6.1.4.1.14823.2.3.2.16.3 | TableenterpriseApSNMPTrapDestinationTable | not-accessible | current | Table of descriptive and status information about configuration of each trap receiving server. |
| 1.3.6.1.4.1.14823.2.3.2.16.3.1 | RowenterpriseApSNMPTrapDestinationEntry | not-accessible | current | An entry in the table, containing information about configuration of one trap receiving server. |
| 1.3.6.1.4.1.14823.2.3.2.16.3.1.1 | ColumnenterpriseApSNMPTrapDestinationIndex | not-accessible | current | Index of the Trap Destination Table. |
| 1.3.6.1.4.1.14823.2.3.2.16.3.1.2 | ColumnenterpriseApSNMPTrapDestinationCommunity | read-write | current | The SNMP Trap Community |
| 1.3.6.1.4.1.14823.2.3.2.16.3.1.3 | ColumnenterpriseApSNMPTrapDestinationIP | read-write | current | The IP address of the trap receiving server. |
| 1.3.6.1.4.1.14823.2.3.2.16.3.1.4 | ColumnenterpriseApSNMPTrapDestinationState | read-write | current | This value indicates whether the trap receiving server is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4 | NodeenterpriseApSNMPTrapFilters | |||
| 1.3.6.1.4.1.14823.2.3.2.16.4.1 | ScalarsysSystemUpTrapEnabled | read-write | current | This value indicates whether the sysSystemUp trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.2 | ScalarsysSystemDownTrapEnabled | read-write | current | This value indicates whether the sysSystemDowntrap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.3 | ScalarsysRadiusServerChangedTrapEnabled | read-write | current | This value indicates whether the sysRadiusServerChanged trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.4 | ScalarsysConfigFileVersionChangedTrapEnabled | read-write | current | This value indicates whether the sysConfigFileVersionChanged trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.5 | Scalardot11StationAssociationTrapEnabled | read-write | current | This value indicates whether the dot11StationAssociation trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.6 | Scalardot11StationReAssociationTrapEnabled | read-write | current | This value indicates whether the dot11StationReAssociation trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.7 | Scalardot11StationAuthenticationTrapEnabled | read-write | current | This value indicates whether the dot11StationAuthentication trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.8 | Scalardot11StationRequestFailTrapEnabled | read-write | current | This value indicates whether the dot11StationRequestFail trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.9 | Scalardot11InterfaceBFailTrapEnabled | read-write | current | This value indicates whether the dot11InterfaceBFail trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.10 | Scalardot11InterfaceAGFailTrapEnabled | read-write | current | This value indicates whether the dot11InterfaceAGFail trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.11 | Scalardot1xMacAddrAuthSuccessTrapEnabled | read-write | current | This value indicates whether the dot1xMacAddrAuthSuccess trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.12 | Scalardot1xMacAddrAuthFailTrapEnabled | read-write | current | This value indicates whether the dot1xMacAddrAuthFail trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.13 | Scalardot1xAuthNotInitiatedTrapEnabled | read-write | current | This value indicates whether the dot1xAuthNotInitiated trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.14 | Scalardot1xAuthSuccessTrapEnabled | read-write | current | This value indicates whether the dot1xAuthSuccess trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.15 | Scalardot1xAuthFailTrapEnabled | read-write | current | This value indicates whether the dot1xAuthFail trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.16 | ScalarlocalMacAddrAuthSuccessTrapEnabled | read-write | current | This value indicates whether the localMacAddrAuthSuccess trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.17 | ScalarlocalMacAddrAuthFailTrapEnabled | read-write | current | This value indicates whether the localMacAddrAuthFail trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.18 | ScalarpppLogonFailTrapEnabled | read-write | current | This value indicates whether the pppLogonFail trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.19 | ScalariappStationRoamedFromTrapEnabled | read-write | current | This value indicates whether the iappStationRoamedFrom trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.20 | ScalariappStationRoamedToTrapEnabled | read-write | current | This value indicates whether the iappStationRoamedTo trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.21 | ScalariappContextDataSentTrapEnabled | read-write | current | This value indicates whether the iappContextDataSent trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.22 | ScalarsntpServerFailTrapEnabled | read-write | current | This value indicates whether the sntpServerFail trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.23 | Scalardot1xSuppAuthenticatedTrapEnabled | read-write | current | This value indicates whether the dot1xSupplicantAuthenticated trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.24 | Scalardot11FailedTransmitsTrapEnabled | read-write | current | This value indicates whether the dot11FailedTransmitsTrapEnabled trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.25 | Scalardot11AckFailuresTrapEnabled | read-write | current | This value indicates whether the dot11AckFailuresTrapEnabled trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.26 | Scalardot11FcsErrorsTrapEnabled | read-write | current | This value indicates whether the dot11FcsErrorsTrapEnabled trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.27 | ScalarrogueAPDetectedTrapEnabled | read-write | current | This value indicates whether the RogueAPDetectedTrapEnabled trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.16.4.28 | ScalarpossibleRogueAPDetectedTrapEnabled | read-write | current | This value indicates whether the RogueAPDetectedTrapEnabled trap is enabled. |
| 1.3.6.1.4.1.14823.2.3.2.17 | NodeenterpriseApSession | |||
| 1.3.6.1.4.1.14823.2.3.2.17.1 | TableenterpriseApSessionTable | not-accessible | current | This table list all sessions (wireless stations) status |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1 | RowenterpriseApSessionEntry | not-accessible | current | An entry in the table, containing information about status and statistics of the wireless station. |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.1 | ColumnenterpriseApSessionIfIndex | not-accessible | current | Interface index for the radio this session is associated with. |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.2 | ColumnenterpriseApSessionStationAddres | not-accessible | current | The unique MAC Address of the station for this session. |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.3 | ColumnenterpriseApSessionAuthenticated | read-only | current | Whether the session is authenticated or not. |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.4 | ColumnenterpriseApSessionAssociated | read-only | current | Whether the session is associated or not. It is rare case that not associated stations show up in the table. |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.5 | ColumnenterpriseApSessionIsForwarding | read-only | current | Whether the AP is forwarding the client station traffic (higher level authentication) |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.6 | ColumnenterpriseApSessionKeyType | read-only | current | The encryption key type used by the station. Note that wpa-wep is not supported |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.7 | ColumnenterpriseApSessionAssociationId | read-only | current | The internal association identify number |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.8 | ColumnenterpriseApSessionLastAuthenticatedTime | read-only | current | This is the time in hundredths of a second last time the client is authenticated. Note that a session may be authenticated multiple times. The value is related… |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.9 | ColumnenterpriseApSessionAssociatedTime | read-only | current | This is the time in hundredths of a second since the client associated. The value is related to the system startup |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.10 | ColumnenterpriseApSessionLastAssociatedTime | read-only | current | This is the time in hundredths of a second when the client associated in last session. The value is related to the system startup |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.11 | ColumnenterpriseApSessionLastDisassociatedTime | read-only | current | This is the time in hundredths of a second when the client disassociated in last session. The value is related to the system startup |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.12 | ColumnenterpriseApSessionTxPacketCount | read-only | current | This is the number of packets transmitted from the client to the AP. It includes data, control and management packets. |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.13 | ColumnenterpriseApSessionRxPacketCount | read-only | current | This is the number of unicast packets transmitted from the AP to the client. It includes data, control and management packets. |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.14 | ColumnenterpriseApSessionTxByteCount | read-only | current | This is the number of bytes transmitted from the client to the AP. It includes the bytes of data, control and management packets. |
| 1.3.6.1.4.1.14823.2.3.2.17.1.1.15 | ColumnenterpriseApSessionRxByteCount | read-only | current | This is the number of unicast bytes transmitted from the AP to the client. It includes the bytes of data, control and management packets. |
| 1.3.6.1.4.1.14823.2.3.2.20 | NodeenterpriseAPVapRadio | |||
| 1.3.6.1.4.1.14823.2.3.2.20.1 | TableenterpriseAPVapRadioTable | not-accessible | current | Table of descriptive and status information about configuration of each radio. |
| 1.3.6.1.4.1.14823.2.3.2.20.1.1 | RowenterpriseAPVapRadioEntry | not-accessible | current | An entry in the table, containing information about configuration of one radio of the AP. |
| 1.3.6.1.4.1.14823.2.3.2.20.1.1.1 | ColumnenterpriseAPVapRadioIndex | not-accessible | current | Radio Index for configuration. |
| 1.3.6.1.4.1.14823.2.3.2.20.1.1.2 | ColumnenterpriseAPVapRadioState | read-write | current | This value indicates the state of the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.20.1.1.3 | ColumnenterpriseAPVapRadioClosedSystem | read-write | current | This value indicates whether closed system is enabled for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.20.1.1.4 | ColumnenterpriseAPVapRadioMaxAssoc | read-write | current | This value indicates the max number of clients allowed on this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.20.1.1.5 | ColumnenterpriseAPVapRadioTransmitKey | read-write | current | This value indicates default transmit key in use for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.20.1.1.6 | ColumnenterpriseAPVapRadioDescription | read-write | current | This value indicates the description for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.20.1.1.8 | ColumnenterpriseAPVapRadioAuthTimeoutInterval | read-write | current | This value indicates the Authentication Timeout interval for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.20.1.1.9 | ColumnenterpriseAPVapRadioAssocTimeoutInterval | read-write | current | This value indicates the Association Timeout interval for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.20.1.1.10 | ColumnenterpriseAPVapRadioWPA2PMKSALifeTime | read-write | current | This value indicates the WPA2 PMSA Life Time for this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.22 | NodeenterpriseApRadioWds | |||
| 1.3.6.1.4.1.14823.2.3.2.22.1 | TableenterpriseApRadioWdsTable | not-accessible | current | Table of configuration information for Wds for each Radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.22.1.1 | RowenterpriseApRadioWdsEntry | not-accessible | current | An entry in the table, containing information about configuration of peer Bridging for one radio of the AP. The table is indexed by radio Index (corresponding … |
| 1.3.6.1.4.1.14823.2.3.2.22.1.1.1 | ColumnwdsApRole | read-write | current | This value indicates the role of the Ap for this radio, roleAp(1): AP operation. roleBridgeMaster(2): Root-Bridge mode. roleBridge(4): Bridge Mode. relay wirel… |
| 1.3.6.1.4.1.14823.2.3.2.22.1.1.3 | ColumnwdsChannelAutoSync | read-write | current | This value indicates the states of channel auto synchronize for this radio. |
| 1.3.6.1.4.1.14823.2.3.2.22.1.1.4 | ColumnwdsMasterSlaveMode | read-write | current | This value indicates the Master/Slave mode for this radio. master (1) To set to master mode. slave (2) To set to slave mode. |
| 1.3.6.1.4.1.14823.2.3.2.22.2 | TableenterpriseApRadioWdsPeerTable | not-accessible | current | Table of configuration information for Wds Peers for each Radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.22.2.1 | RowenterpriseApRadioWdsPeerEntry | not-accessible | current | An entry in the table, containing information about configuration of peer Bridging for one radio of the AP. The table is indexed by radio Index (corresponding … |
| 1.3.6.1.4.1.14823.2.3.2.22.2.1.1 | ColumnwdsPeerIndex | not-accessible | current | Peer Index for the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.22.2.1.2 | ColumnwdsPeerBssid | read-write | current | The BSSID for this peer. |
| 1.3.6.1.4.1.14823.2.3.2.24 | NodeenterpriseApWMM | |||
| 1.3.6.1.4.1.14823.2.3.2.24.1 | TableenterpriseApWMMTable | not-accessible | current | The table of WMM information for each radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.1.1 | RowenterpriseApWMMEntry | not-accessible | current | An entry of table, contains the WMM information. |
| 1.3.6.1.4.1.14823.2.3.2.24.1.1.1 | ColumnenterpriseApWMMModeIndex | not-accessible | current | Peer Index for the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.1.1.2 | ColumnenterpriseApWMMMode | read-write | current | This value indicates the WMM mode for the radio interface. disabled(1) To set WMM mode disabled. support (2) To set WMM mode supported. required(3) To set WMM … |
| 1.3.6.1.4.1.14823.2.3.2.24.2 | TableenterpriseApWMMAckPolicyTable | not-accessible | current | The table of WMM Ack Policy information for each ac number on the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.2.1 | RowenterpriseApWMMAckPolicyEntry | not-accessible | current | An entry of table, contains the WMM Ack Policy information. |
| 1.3.6.1.4.1.14823.2.3.2.24.2.1.1 | ColumnenterpriseApWMMAckPolicyIndex | read-only | current | |
| 1.3.6.1.4.1.14823.2.3.2.24.2.1.2 | ColumnenterpriseApWMMACKPolicy | read-write | current | This value indicates WMM Ack Policy state of each ac number for the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.3 | TableenterpriseApWMMBSSParamTable | not-accessible | current | The table of WMM BSS parameter information. |
| 1.3.6.1.4.1.14823.2.3.2.24.3.1 | RowenterpriseApWMMBSSParamEntry | not-accessible | current | An entry of table, contains the WMM BSS parameter information for each ac number on the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.3.1.1 | ColumnenterpriseApWMMBSSParamIndex | read-only | current | |
| 1.3.6.1.4.1.14823.2.3.2.24.3.1.2 | ColumnenterpriseApWMMBSSParamLogCwMin | read-write | current | This value indicates the WMM BSS parameter logCwMin of AC number for the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.3.1.3 | ColumnenterpriseApWMMBSSParamLogCwMax | read-write | current | This value indicates the WMM BSS parameter logCwMax of each AC number for the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.3.1.4 | ColumnenterpriseApWMMBSSParamAIFSN | read-write | current | This value indicates the WMM BSS parameters AIFSN of each AC number for the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.3.1.5 | ColumnenterpriseApWMMBSSParamTXOPLimit | read-write | current | This value indicates the WMM BSS parameters TXOP Limit of each AC number for the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.3.1.6 | ColumnenterpriseApWMMBSSParamAdmissionCtrl | read-write | current | This value indicates the BSS parameters Admission Control of each AC number for the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.4 | TableenterpriseApWMMAPParamTable | not-accessible | current | The table of configuration information for WMM AP parameters for each ac number on the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.4.1 | RowenterpriseApWMMAPParamEntry | not-accessible | current | An entry table, include the Ap parameter information for each ac numbers. |
| 1.3.6.1.4.1.14823.2.3.2.24.4.1.1 | ColumnenterpriseApWMMAPParamIndex | read-only | current | |
| 1.3.6.1.4.1.14823.2.3.2.24.4.1.2 | ColumnenterpriseApWMMAPParamLogCwMin | read-write | current | This value indicates the LogCwMin of AP parameter for each AC number on the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.4.1.3 | ColumnenterpriseApWMMAPParamLogCwMax | read-write | current | This value indicates the LogCwMax of AP parameter for each AC number on the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.4.1.4 | ColumnenterpriseApWMMAPParamAIFSN | read-write | current | This value indicates the AIFSN of AP parameter for each AC number on the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.4.1.5 | ColumnenterpriseApWMMAPParamTXOPLimit | read-write | current | This value indicates the TXOP Limit of AP parameter for each AC number on the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.24.4.1.6 | ColumnenterpriseApWMMAPParamAdmissionCtrl | read-write | current | This value indicates the admission control of AP parameter for each AC number on the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.25 | NodeenterpriseApSTP | |||
| 1.3.6.1.4.1.14823.2.3.2.25.1 | ScalarenterpriseApSTPBridgeStatus | read-write | current | This value indicates the STP bridge status for the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.25.2 | ScalarenterpriseApSTPBridgePriority | read-write | current | This value indicates the STP bridge priority for the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.25.3 | ScalarenterpriseApSTPBridgeMaxAge | read-write | current | This value indicates the STP bridge max age for the radio interface.(unit: second) |
| 1.3.6.1.4.1.14823.2.3.2.25.4 | ScalarenterpriseApSTPHelloTime | read-write | current | This value indicates the STP hello time for the radio interface.(unit: second) |
| 1.3.6.1.4.1.14823.2.3.2.25.5 | ScalarenterpriseApSTPBridgeForwardingDelay | read-write | current | This value indicates the STP forwarding delay for the radio interface.(unit: second) |
| 1.3.6.1.4.1.14823.2.3.2.25.6 | NodeenterpriseApSTPRadioInterface | |||
| 1.3.6.1.4.1.14823.2.3.2.25.6.1 | TableenterpriseApSTPNodeTable | not-accessible | current | The table of STP link Path Cost and link port priority information for each nodes on radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.25.6.1.1 | RowenterpriseApSTPNodeEntry | not-accessible | current | An entry in a table, contain the link path cost and link port priroity information. |
| 1.3.6.1.4.1.14823.2.3.2.25.6.1.1.1 | ColumnenterpriseApSTPNodeIndex | not-accessible | current | Peer Index for the nodes on the radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.25.6.1.1.2 | ColumnenterpriseApSTPNodeLinkPathCost | read-write | current | This value indicates the link path cost for the node on this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.25.6.1.1.3 | ColumnenterpriseApSTPNodeLinkPortPriority | read-write | current | This value indicates the link path cost for the node on this radio interface. |
| 1.3.6.1.4.1.14823.2.3.2.25.7 | NodeenterpriseApSTPEthernetInterface | |||
| 1.3.6.1.4.1.14823.2.3.2.25.7.1 | ScalarenterpriseApSTPEthernetLinkPathCost | read-write | current | This value indicates link path cost for ethernet interface. |
| 1.3.6.1.4.1.14823.2.3.2.25.7.2 | ScalarenterpriseApSTPEthernetLinkPortPriority | read-write | current | This value indicates link port prirorty for ethernet interface. |