BIANCA-BRICK-E3-MIB
28 objects
No module-level DESCRIPTION found.
Imported Objects
| BINTEC-MIB MISSING | Date HexValue |
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.272 | Nodebintec | |||
| 1.3.6.1.4.1.272.4 | Nodebibo | |||
| 1.3.6.1.4.1.272.4.42 | Nodee3 | |||
| 1.3.6.1.4.1.272.4.42.1 | Tablee3IfTable | not-accessible | mandatory | The e3IfTable contains information relating to the interfaces available on the system. Each entry corresponds to an available e3 interface. Entries cannot be a… |
| 1.3.6.1.4.1.272.4.42.1.1 | Rowe3IfEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.42.1.1.1 | Columne3IfIndex | read-only | mandatory | The unique interface index of the e3/ds3 interface. |
| 1.3.6.1.4.1.272.4.42.1.1.2 | Columne3IfType | read-write | mandatory | The e3 physical interface type off(1) interface is switched offline and the line interface unit is switched off. e3-unframed(2) Synchronous 34.368 MBit/s fulld… |
| 1.3.6.1.4.1.272.4.42.1.1.5 | Columne3IfClock | read-write | mandatory | The clock source of the E3/DS3 connection. intern(1) Your router provides the master clock of the E3/DS3 connection. extern(2) Your telephone company or the re… |
| 1.3.6.1.4.1.272.4.42.1.1.10 | Columne3IfL2Mode | read-write | mandatory | The X.75 layer 2 mode. This value has influence on the HDLC address field (first byte of a HDCL frame). When configured as DTE the address in a command frame i… |
| 1.3.6.1.4.1.272.4.42.1.1.11 | Columne3IfTestPattern | read-write | mandatory | This variable configures which test pattern should be transmitted. normal(1) normal data, no test pattern is transmitted. ones(2) Transmit unframed all ones. a… |
| 1.3.6.1.4.1.272.4.42.1.1.12 | Columne3IfLoopback | read-write | mandatory | This variable represents the loopback configuration of the E3/DS3 interface. noloop(1) No loopback is configured, normal data is transmitted and received. remo… |
| 1.3.6.1.4.1.272.4.42.1.1.14 | Columne3IfBundle | read-write | mandatory | Index of the bundle to aggregate the interface and channels of other interfaces to one interface. |
| 1.3.6.1.4.1.272.4.42.1.1.15 | Columne3IfCableLength | read-write | mandatory | 'short' should be used for a cable lenght less then 225 feet. 'long' should be used otherwise. With 'short' the Tx signal is preattenutated similar to the atte… |
| 1.3.6.1.4.1.272.4.42.1.1.16 | Columne3IfCRCMode | read-write | mandatory | The type of CRC checksum of the HDLC frames. crc16(1) 16 Bit CRC crc32(2) 32 Bit CRC |
| 1.3.6.1.4.1.272.4.42.1.1.19 | Columne3IfL1State | read-only | mandatory | The e3 physical layer state down(1) physical layer is inactive up(2) physical layer is active prbs(3) physical layer is active, a PRBS signal is detected nolic… |
| 1.3.6.1.4.1.272.4.42.1.1.20 | Columne3IfRxPackets | read-only | mandatory | Count of received valid HDLC Frames. |
| 1.3.6.1.4.1.272.4.42.1.1.21 | Columne3IfRxOctets | read-only | mandatory | Count of received bytes. |
| 1.3.6.1.4.1.272.4.42.1.1.22 | Columne3IfTxPackets | read-only | mandatory | Count of transmitted valid HDLC Frames. |
| 1.3.6.1.4.1.272.4.42.1.1.23 | Columne3IfTxOctets | read-only | mandatory | Count of transmitted bytes. |
| 1.3.6.1.4.1.272.4.42.1.1.24 | Columne3IfRxResets | read-only | mandatory | Count of receiver resets. Under rare circumstances it might be necessary to reset the receiver to work properly. |
| 1.3.6.1.4.1.272.4.42.1.1.25 | Columne3IfRxAborts | read-only | mandatory | Count of receiver aborts. The sender of a frame can indicate a frame as aborted with a special Abort sequence. |
| 1.3.6.1.4.1.272.4.42.1.1.26 | Columne3IfRxOverruns | read-only | mandatory | Count of receiver overruns. If the e3 port is unable to grant sufficiently soon/often the bus, the RxFIFO may fill up. This leads to loss of data. |
| 1.3.6.1.4.1.272.4.42.1.1.27 | Columne3IfRxCRCErrors | read-only | mandatory | Count of corrupted frames. Errors due to interference on the e3 cable. |
| 1.3.6.1.4.1.272.4.42.1.1.28 | Columne3IfRxGiantFrames | read-only | mandatory | Count of received frames with illegal framesize. This can occur if a frame delimiter is destroyed. |
| 1.3.6.1.4.1.272.4.42.1.1.29 | Columne3IfTxResets | read-only | mandatory | Count of transmitter resets. Under rare circumstances it might be necessary to reset the transmitter to work properly. |
| 1.3.6.1.4.1.272.4.42.1.1.30 | Columne3IfTxAborts | read-only | mandatory | Count of transmitter aborts. While sending a frame it might be necessary to indicate this frame as aborted. In this case the receiver regards this frame as ill… |
| 1.3.6.1.4.1.272.4.42.1.1.31 | Columne3IfTxUnderruns | read-only | mandatory | Count of transmitter underruns. The e3 data for the e3 port is supplied too slowly. |
| 1.3.6.1.4.1.272.4.42.1.1.32 | Columne3IfTxGiantFrames | read-only | mandatory | Count of transmitted frames with illegal framesize. This can occur if an upper module creates packets with more than the maximum allowed packet size. |