BIANCA-BRICK-PPP-MIB
275 objects
No module-level DESCRIPTION found.
Imported Objects
| BINTEC-MIB MISSING | BitValue Date |
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises IpAddress |
| RFC1158-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.272 | Nodebintec | |||
| 1.3.6.1.4.1.272.4 | Nodebibo | |||
| 1.3.6.1.4.1.272.4.3 | Nodeppp | |||
| 1.3.6.1.4.1.272.4.3.1 | TablebiboPPPTable | not-accessible | mandatory | The biboPPPTable contains configuration information for the PPP interfaces. Each time a new entry is made here, a corresponding entry is made in the ifTable. C… |
| 1.3.6.1.4.1.272.4.3.1.1 | RowbiboPPPEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.3.1.1.1 | ColumnbiboPPPIfIndex | read-only | mandatory | Correlating PPP interface index. This value is assigned automatically by the system. |
| 1.3.6.1.4.1.272.4.3.1.1.2 | ColumnbiboPPPType | read-write | mandatory | The type of the PPP multiprotocol interface. A new dialup interface is created when this field is set to the value isdn-dialup(1), isdn-dialin-only(3) or multi… |
| 1.3.6.1.4.1.272.4.3.1.1.3 | ColumnbiboPPPEncapsulation | read-write | mandatory | The layer 2 encapsulation of the link. The use of ppp(1) as described in RFC 1661 is the preferred encapsulation for point-to-point links. The encapsulation is… |
| 1.3.6.1.4.1.272.4.3.1.1.4 | ColumnbiboPPPKeepalive | read-write | obsolete | When set to on(1), keepalive packets are sent in regular intervals during the connection. Keepalive packets can not be sent using the ip-lapb or x25 encapsulat… |
| 1.3.6.1.4.1.272.4.3.1.1.5 | ColumnbiboPPPTimeout | read-write | mandatory | The number of milliseconds waiting before retransmitting a PPP configure packet. |
| 1.3.6.1.4.1.272.4.3.1.1.6 | ColumnbiboPPPCompression | read-write | mandatory | The throughput can be enhanced up to factor three using the V42bis compression method or the Stac LZS compression algorithm. V42bis is currently supported with… |
| 1.3.6.1.4.1.272.4.3.1.1.7 | ColumnbiboPPPAuthentication | read-write | mandatory | The type of authentication used on the point-to-point link as described in RFC 1334. The authentication protocol supports pap(2) (Password Authentication Proto… |
| 1.3.6.1.4.1.272.4.3.1.1.8 | ColumnbiboPPPAuthIdent | read-write | mandatory | The remote authentication identification string. The local authentication identification string is taken from the contents of the variable biboPPPLocalIdent. |
| 1.3.6.1.4.1.272.4.3.1.1.9 | ColumnbiboPPPAuthSecret | read-write | mandatory | The authentication secret, which is used symmetrically for both local and remote sides of the PPP link. |
| 1.3.6.1.4.1.272.4.3.1.1.10 | ColumnbiboPPPIpAddress | read-write | mandatory | The IP control protocol as described in RFC1332 has a means of negotiating IP-addresses. When this option is set to dynamic-server(2), an available IP-address … |
| 1.3.6.1.4.1.272.4.3.1.1.11 | ColumnbiboPPPRetryTime | read-write | mandatory | Time in seconds to wait before retrying an ISDN call or PPTP control connection. This value is also used as timeout for the delayed callback (see biboPPPCallba… |
| 1.3.6.1.4.1.272.4.3.1.1.12 | ColumnbiboPPPBlockTime | read-write | mandatory | Time in seconds to wait after a connection failure (e.g. the number of biboPPPMaxRetries calls failed). When set to zero, the interface state is never set to b… |
| 1.3.6.1.4.1.272.4.3.1.1.13 | ColumnbiboPPPMaxRetries | read-write | mandatory | The number of dialup retries before changing to the blocked state. |
| 1.3.6.1.4.1.272.4.3.1.1.14 | ColumnbiboPPPShortHold | read-write | mandatory | The time in seconds to wait, once the channel is silent, (that is, no data is being received or transmitted) before terminating the link. When set to zero the … |
| 1.3.6.1.4.1.272.4.3.1.1.15 | ColumnbiboPPPInitConn | read-write | mandatory | The number of channels to initially set up for this interface. |
| 1.3.6.1.4.1.272.4.3.1.1.16 | ColumnbiboPPPMaxConn | read-write | mandatory | The maximum number of channels bundled for this interface. |
| 1.3.6.1.4.1.272.4.3.1.1.17 | ColumnbiboPPPMinConn | read-write | mandatory | The minimum number of channels bundled for this interface. |
| 1.3.6.1.4.1.272.4.3.1.1.18 | ColumnbiboPPPCallback | read-write | mandatory | If this object is enabled(1), and the call is recognized by the dialed number then calls are never accepted, and a callback is forced for incoming calls at onc… |
| 1.3.6.1.4.1.272.4.3.1.1.19 | ColumnbiboPPPLayer1Protocol | read-write | mandatory | This entry is used to select the layer 1 protocol settings for this partner. Normally the correct entry is hdlc-64. |
| 1.3.6.1.4.1.272.4.3.1.1.20 | ColumnbiboPPPLoginString | read-write | mandatory | A textual string containing a login sequence (script) composed of fields in the format [expect send], comparable to chat scripts commonly used on other sytems.… |
| 1.3.6.1.4.1.272.4.3.1.1.21 | ColumnbiboPPPVJHeaderComp | read-write | mandatory | This entry is used to enable Van Jacobsen TCP/IP header compression, which reduces the size of TCP/IP packet headers and increases the efficiency of line utili… |
| 1.3.6.1.4.1.272.4.3.1.1.22 | ColumnbiboPPPLayer2Mode | read-write | mandatory | This object specifies the layer 2 mode to be used for a connection. It is only relevant, if the Encapsulation involves an LAPB protocol. This is the case for x… |
| 1.3.6.1.4.1.272.4.3.1.1.23 | ColumnbiboPPPDynShortHold | read-write | mandatory | Optimizes idle time disconnects depending on the charging information received during the connection. This value specifies the minimum inactivity time (channel… |
| 1.3.6.1.4.1.272.4.3.1.1.24 | ColumnbiboPPPLocalIdent | read-write | mandatory | This is the local identification string used for PPP authentication(PAP/CHAP/MS-CHAP). |
| 1.3.6.1.4.1.272.4.3.1.1.25 | ColumnbiboPPPDNSNegotiation | read-write | mandatory | The IP control protocol extensions as described in RFC 1877 has a means of negotiating primary and secondary Domain Name System (DNS) server addresses. When th… |
| 1.3.6.1.4.1.272.4.3.1.1.26 | ColumnbiboPPPEncryption | read-write | mandatory | This field specifies the data encryption scheme for en(de)crypting PPP encapsulated multi-protocol datagrams. Setting to mppe-40(2), mppe-128(3) or mppe-56(7) … |
| 1.3.6.1.4.1.272.4.3.1.1.27 | ColumnbiboPPPLQMonitoring | read-write | mandatory | This parameter enables (2) or disables (1) PPP Link Quality Monitoring (LQM) according RFC 1989. When set to on(2) LQM is added to the list of parameters used … |
| 1.3.6.1.4.1.272.4.3.1.1.28 | ColumnbiboPPPIpPoolId | read-write | mandatory | Pool ID value to select an IP address pool for dynamic IP address assignment via IPCP. See also PPPIpPoolTable for further details. |
| 1.3.6.1.4.1.272.4.3.1.1.29 | ColumnbiboPPPSessionTimeout | read-write | mandatory | Maximum number of seconds before termination the established PPP session, regardless there is any data throughput on the corresponding link(s). When set to 0, … |
| 1.3.6.1.4.1.272.4.3.1.1.30 | ColumnbiboPPPLayer1DiscDelay | read-write | mandatory | This parameter specifies wether the link (layer 1) should be disconnected immediately (after receiving a layer 2 disconnect) or delayed (after expiration of bi… |
| 1.3.6.1.4.1.272.4.3.1.1.31 | ColumnbiboPPPAuthDomain | read-write | mandatory | The authentication domain, which is used for authenticating via MS-CHAP with enabled DomainName. |
| 1.3.6.1.4.1.272.4.3.1.1.32 | ColumnbiboPPPAliveCheck | read-write | mandatory | When set to enabled(1), LCP Echo Request (in case of encapsulation PPP) or Cisco-HDLC keepalive messages (in case of encapsulation cisco-hdlc) are sent in regu… |
| 1.3.6.1.4.1.272.4.3.2 | TablebiboPPPStatTable | not-accessible | mandatory | The biboPPPStatTable contains statistical connection- specific information. Only the system can add or delete entries to this table. Creating entries: Entries … |
| 1.3.6.1.4.1.272.4.3.2.1 | RowbiboPPPStatEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.3.2.1.1 | ColumnbiboPPPConnIfIndex | read-only | mandatory | Correlating PPP interface index. |
| 1.3.6.1.4.1.272.4.3.2.1.2 | ColumnbiboPPPConnActive | read-only | mandatory | The actual number of bundled channels. |
| 1.3.6.1.4.1.272.4.3.2.1.3 | ColumnbiboPPPConnProtocols | read-only | mandatory | The bitwise ORed protocols successfully negotiated on this connection; currently the following protocols are supported: tcp/ip(1), ipx(2), bridge(4), bpdu(8), … |
| 1.3.6.1.4.1.272.4.3.2.1.4 | ColumnbiboPPPConnState | read-only | mandatory | The physical state of the link. This field is obsolete and will not be supported in a future release. |
| 1.3.6.1.4.1.272.4.3.2.1.5 | ColumnbiboPPPConnDuration | read-only | mandatory | The current link duration on this interface in seconds. |
| 1.3.6.1.4.1.272.4.3.2.1.6 | ColumnbiboPPPConnUnits | read-only | mandatory | The current costs on this interface for all member links. |
| 1.3.6.1.4.1.272.4.3.2.1.7 | ColumnbiboPPPConnTransmitOctets | read-only | mandatory | The octets transmitted on this interface since its last change to the 'up' state. |
| 1.3.6.1.4.1.272.4.3.2.1.8 | ColumnbiboPPPConnReceivedOctets | read-only | mandatory | The octets received since its last change to the `up' state. |
| 1.3.6.1.4.1.272.4.3.2.1.9 | ColumnbiboPPPConnOutgoingCalls | read-only | mandatory | The number of outgoing calls on this interface since its last change to the 'up' state. |
| 1.3.6.1.4.1.272.4.3.2.1.10 | ColumnbiboPPPConnOutgoingFails | read-only | mandatory | The number of outgoing call failures on this interface since its last change to the 'up' state. |
| 1.3.6.1.4.1.272.4.3.2.1.11 | ColumnbiboPPPConnIncomingCalls | read-only | mandatory | The number of incoming calls on this interface since its last change to the up state. |
| 1.3.6.1.4.1.272.4.3.2.1.12 | ColumnbiboPPPConnIncomingFails | read-only | mandatory | The number of incoming call failures on this interface since its last change to the up state. |
| 1.3.6.1.4.1.272.4.3.2.1.13 | ColumnbiboPPPTotalDuration | read-only | mandatory | The total link duration in seconds. |
| 1.3.6.1.4.1.272.4.3.2.1.14 | ColumnbiboPPPTotalUnits | read-only | mandatory | The total costs on this interface for all member links. |
| 1.3.6.1.4.1.272.4.3.2.1.15 | ColumnbiboPPPTotalTransmitOctets | read-only | mandatory | The total amount of octets transmitted. |
| 1.3.6.1.4.1.272.4.3.2.1.16 | ColumnbiboPPPTotalReceivedOctets | read-only | mandatory | The total amount of octets received. |
| 1.3.6.1.4.1.272.4.3.2.1.17 | ColumnbiboPPPTotalOutgoingCalls | read-only | mandatory | The total number of outgoing calls. |
| 1.3.6.1.4.1.272.4.3.2.1.18 | ColumnbiboPPPTotalOutgoingFails | read-only | mandatory | The total number of outgoing call failures. |
| 1.3.6.1.4.1.272.4.3.2.1.19 | ColumnbiboPPPTotalIncomingCalls | read-only | mandatory | The total number of incoming calls. |
| 1.3.6.1.4.1.272.4.3.2.1.20 | ColumnbiboPPPTotalIncomingFails | read-only | mandatory | The total number of incoming call failures. |
| 1.3.6.1.4.1.272.4.3.2.1.21 | ColumnbiboPPPThroughput | read-only | mandatory | The actual throughput of the interface; updated every 5 seconds. Note that only the actual maximum of the both directions (send / receive) is considered. |
| 1.3.6.1.4.1.272.4.3.2.1.23 | ColumnbiboPPPChargeInterval | read-only | mandatory | Describes the measured interval between charging info elements received from the ISDN network. |
| 1.3.6.1.4.1.272.4.3.2.1.24 | ColumnbiboPPPIdleTime | read-only | mandatory | The currently measured connection inactivity time (channel is silent). |
| 1.3.6.1.4.1.272.4.3.2.1.25 | ColumnbiboPPPConnCharge | read-only | mandatory | The current charge on this interface as 1/1000 of the respective currency. |
| 1.3.6.1.4.1.272.4.3.2.1.26 | ColumnbiboPPPTotalCharge | read-only | mandatory | The total charge on this interface as 1/1000 of the respective currency. |
| 1.3.6.1.4.1.272.4.3.2.1.27 | ColumnbiboPPPLastConnDuration | read-only | mandatory | The duration of the last connection on this interface in seconds. |
| 1.3.6.1.4.1.272.4.3.2.1.28 | ColumnbiboPPPLastConnIdle | read-only | mandatory | The inactivity time of the last connection on this interface in seconds. |
| 1.3.6.1.4.1.272.4.3.3 | TablebiboPPPLinkTable | not-accessible | mandatory | The biboPPPLinkTable contains statistical information for each current PPP link on the system. Only the system can add or delete entries to this table. Creatin… |
| 1.3.6.1.4.1.272.4.3.3.1 | RowbiboPPPLinkEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.3.3.1.1 | ColumnbiboPPPLinkIfIndex | read-only | mandatory | Correlating PPP interface index. |
| 1.3.6.1.4.1.272.4.3.3.1.2 | ColumnbiboPPPLinkEstablished | read-only | mandatory | Time when the link was established. |
| 1.3.6.1.4.1.272.4.3.3.1.3 | ColumnbiboPPPLinkDirection | read-only | mandatory | Direction of link, incoming(1) or outgoing(2). In case of permanent links, the meaning is dce(1) or dte(2). |
| 1.3.6.1.4.1.272.4.3.3.1.4 | ColumnbiboPPPLinkProtocols | read-only | mandatory | The bitwise ORed protocols successfully negotiated on this link; currently the following protocols are supported: tcp/ip(1), ipx(2), bridge(4), bpdu(8), x25(16… |
| 1.3.6.1.4.1.272.4.3.3.1.5 | ColumnbiboPPPLinkState | read-only | mandatory | The actual state of each link in a bundle. The link is fully operational in the up(1) state, and not operational in the down(2) state. The starting(3) state is… |
| 1.3.6.1.4.1.272.4.3.3.1.6 | ColumnbiboPPPLinkUnits | read-only | mandatory | The costs for this link in units. |
| 1.3.6.1.4.1.272.4.3.3.1.7 | ColumnbiboPPPLinkRetries | read-only | mandatory | The amount of retries taken to establish the link. |
| 1.3.6.1.4.1.272.4.3.3.1.8 | ColumnbiboPPPLinkKeepaliveSent | read-only | mandatory | The amount of keepalive packets sent on the link. |
| 1.3.6.1.4.1.272.4.3.3.1.9 | ColumnbiboPPPLinkKeepalivePending | read-only | mandatory | The amount of keepalive answer packets waiting for since the last occurance of an echo reply packet. |
| 1.3.6.1.4.1.272.4.3.3.1.10 | ColumnbiboPPPLinkDeviceIndex | read-only | mandatory | The underlying link device index. |
| 1.3.6.1.4.1.272.4.3.3.1.11 | ColumnbiboPPPLinkSpeed | read-only | mandatory | The speed of the link. |
| 1.3.6.1.4.1.272.4.3.3.1.13 | ColumnbiboPPPLinkStkNumber | read-only | mandatory | The stack number of the dialup link, correlating to the isdnCallStkNumber field in the isdnCallTable. |
| 1.3.6.1.4.1.272.4.3.3.1.14 | ColumnbiboPPPLinkCallType | read-only | mandatory | The call type of the dialup link, correlating to the isdnCallType field in the isdnCallTable. |
| 1.3.6.1.4.1.272.4.3.3.1.15 | ColumnbiboPPPLinkCallReference | read-only | mandatory | The call reference of the dialup link, correlating to the isdnCallReference field in the isdnCallTable. |
| 1.3.6.1.4.1.272.4.3.3.1.16 | ColumnbiboPPPLinkCharge | read-only | mandatory | The costs for this link as 1/1000 of the respective currency. |
| 1.3.6.1.4.1.272.4.3.3.1.17 | ColumnbiboPPPLinkAccm | read-only | mandatory | The Asynchronous Control Character Map (ACCM) according RFC 1662. |
| 1.3.6.1.4.1.272.4.3.3.1.18 | ColumnbiboPPPLinkLqm | read-only | mandatory | Indicates the successful negotiation of the Link Quality Protocol (LQM). |
| 1.3.6.1.4.1.272.4.3.3.1.19 | ColumnbiboPPPLinkLcpComp | read-only | mandatory | Address- and Protocol-Field compression. |
| 1.3.6.1.4.1.272.4.3.3.1.20 | ColumnbiboPPPLinkLocDiscr | read-only | mandatory | Local LCP multilink endpoint discriminator. |
| 1.3.6.1.4.1.272.4.3.3.1.21 | ColumnbiboPPPLinkRemDiscr | read-only | mandatory | Peer's LCP multilink endpoint discriminator. |
| 1.3.6.1.4.1.272.4.3.3.1.22 | ColumnbiboPPPLinkL1Protocol | read-only | mandatory | The layer 1 protocol of this link. |
| 1.3.6.1.4.1.272.4.3.3.1.23 | ColumnbiboPPPLinkLocAuth | read-only | mandatory | The result of the PPP authentication procedure performed locally. |
| 1.3.6.1.4.1.272.4.3.3.1.24 | ColumnbiboPPPLinkRemAuth | read-only | mandatory | The result of the PPP authentication procedure performed on remote. |
| 1.3.6.1.4.1.272.4.3.3.1.25 | ColumnbiboPPPLinkNRxDesc | read-only | mandatory | This variable contains the number of receive descriptors used by the interface driver of the respective link. |
| 1.3.6.1.4.1.272.4.3.3.1.26 | ColumnbiboPPPLinkNTxDesc | read-only | mandatory | This variable contains the number of transmit descriptors used by the interface driver of the respective link. |
| 1.3.6.1.4.1.272.4.3.4 | TablebiboPPPIpAssignTable | not-accessible | mandatory | The biboPPPIpAssignTable contains IP addresses used when dynamically assigning IP addresses; i.e. when the biboPPPIpAddress field is set to `dynamic'. Creating… |
| 1.3.6.1.4.1.272.4.3.4.1 | RowbiboPPPIpAssignEntry | not-accessible | mandatory | Pool of IP addresses for dynamic IP address assignment via IPCP. See the biboPPPIpAddress field for further explanation. |
| 1.3.6.1.4.1.272.4.3.4.1.1 | ColumnbiboPPPIpAssignAddress | read-write | mandatory | First IP address of this range. |
| 1.3.6.1.4.1.272.4.3.4.1.2 | ColumnbiboPPPIpAssignState | read-write | mandatory | If an entry is currently in use, the state is set to as- signed(1). Otherwise it is set to unused(2). You may also delete this entry by changing it to delete(3… |
| 1.3.6.1.4.1.272.4.3.4.1.3 | ColumnbiboPPPIpAssignPoolId | read-write | mandatory | Pool ID value. |
| 1.3.6.1.4.1.272.4.3.4.1.4 | ColumnbiboPPPIpAssignRange | read-write | mandatory | Number of IP addresses that will be assigned starting from biboPPPIpAssignAddress. A range of 0 will disable this entry |
| 1.3.6.1.4.1.272.4.3.4.1.5 | ColumnbiboPPPIpAssignDescription | read-write | mandatory | Optional IP pool description. |
| 1.3.6.1.4.1.272.4.3.5 | TablebiboPPPProfileTable | not-accessible | mandatory | The biboPPPProfileTable contains PPP default parameters used for PPP negotiation with unknown dialin partners. For PPP connections, PPP profiles are asigned to… |
| 1.3.6.1.4.1.272.4.3.5.1 | RowbiboPPPProfileEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.3.5.1.1 | ColumnbiboPPPProfileName | read-only | mandatory | The name of the PPP profile. Three profiles are available. |
| 1.3.6.1.4.1.272.4.3.5.1.2 | ColumnbiboPPPProfileAuthProtocol | read-write | mandatory | The type of authentication used on the point-to-point link as described in RFC 1334. See biboPPPAuthentication for further details. |
| 1.3.6.1.4.1.272.4.3.5.1.3 | ColumnbiboPPPProfileAuthRadius | read-write | mandatory | This entry is used to configure possible RADIUS authentication on incoming calls. The default value is inband(2), only inband RADIUS requests (PAP, CHAP) are s… |
| 1.3.6.1.4.1.272.4.3.5.1.4 | ColumnbiboPPPProfileLQMonitoring | read-write | mandatory | This parameter enables (2) or disables (1) PPP Link Quality Monitoring (LQM) according RFC 1989. When set to on(2) LQM is added to the list of parameters ackno… |
| 1.3.6.1.4.1.272.4.3.5.1.5 | ColumnbiboPPPProfilePPPoEDevIfIndex | read-write | mandatory | Specifies the device to be used for PPP over Ethernet (PPPoE) according RFC 2516. |
| 1.3.6.1.4.1.272.4.3.5.1.7 | ColumnbiboPPPProfileCallbackNegotiation | read-write | mandatory | Specifies wether callback negotiation (LCP/CBCP) is allowed or not. If set to disabled(1), no callback negotiation will be performed or accepted. If set to ena… |
| 1.3.6.1.4.1.272.4.3.6 | TablepppLqmTable | not-accessible | mandatory | The pppLqmTable contains statistical information for each current PPP link on the system. Only the system can add or delete entries to this table. Creating ent… |
| 1.3.6.1.4.1.272.4.3.6.1 | RowpppLqmEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.3.6.1.1 | ColumnpppLqmIfIndex | read-only | mandatory | Correlating PPP interface index. |
| 1.3.6.1.4.1.272.4.3.6.1.2 | ColumnpppLqmCallReference | read-only | mandatory | The call reference of the dialup link, correlating to the isdnCallReference field in the isdnCallTable. |
| 1.3.6.1.4.1.272.4.3.6.1.3 | ColumnpppLqmReportingPeriod | read-only | mandatory | The LQMReportingPeriod field indicates the maximum time in hundredths of seconds between transmission of Link Quality Reports (LQR). The peer may transmit pack… |
| 1.3.6.1.4.1.272.4.3.6.1.4 | ColumnpppLqmOutLQRs | read-only | mandatory | Number of transmitted Link Quality Reports (LQR) on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.5 | ColumnpppLqmOutPackets | read-only | mandatory | Number of transmitted Packets on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.6 | ColumnpppLqmOutOctets | read-only | mandatory | Number of transmitted Octets on this link, including framing data. |
| 1.3.6.1.4.1.272.4.3.6.1.7 | ColumnpppLqmInLQRs | read-only | mandatory | Number of Link Quality Reports (LQR) received on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.8 | ColumnpppLqmInPackets | read-only | mandatory | Number of Packets reveived on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.9 | ColumnpppLqmInOctets | read-only | mandatory | Number of Octets reveived on this link, including framing data. |
| 1.3.6.1.4.1.272.4.3.6.1.10 | ColumnpppLqmInDiscards | read-only | mandatory | Number of Packets received on this link, but discarded. |
| 1.3.6.1.4.1.272.4.3.6.1.11 | ColumnpppLqmInErrors | read-only | mandatory | Number of errorneous Packets received on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.12 | ColumnpppLqmPeerOutLQRs | read-only | mandatory | Number of Link Quality Reports (LQR) transmitted by remote on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.13 | ColumnpppLqmPeerOutPackets | read-only | mandatory | Number of Packets transmitted by remote on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.14 | ColumnpppLqmPeerOutOctets | read-only | mandatory | Number of Octets transmitted by remote on this link, including framing data. |
| 1.3.6.1.4.1.272.4.3.6.1.15 | ColumnpppLqmPeerInLQRs | read-only | mandatory | Number of Link Quality Reports (LQR) received by remote on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.16 | ColumnpppLqmPeerInPackets | read-only | mandatory | Number of Packets reveived by remote on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.17 | ColumnpppLqmPeerInOctets | read-only | mandatory | Number of Octets reveived by remote on this link, including framing data. |
| 1.3.6.1.4.1.272.4.3.6.1.18 | ColumnpppLqmPeerInDiscards | read-only | mandatory | Number of Packets received by remote on this link, but discarded. |
| 1.3.6.1.4.1.272.4.3.6.1.19 | ColumnpppLqmPeerInErrors | read-only | mandatory | Number of errorneous Packets received by remote on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.20 | ColumnpppLqmLostOutLQRs | read-only | mandatory | Number of lost Link Quality Reports (LQR) transmitted on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.21 | ColumnpppLqmLostOutPackets | read-only | mandatory | Number of lost Packets transmitted on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.22 | ColumnpppLqmLostOutOctets | read-only | mandatory | Number of lost Octets transmitted on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.23 | ColumnpppLqmLostPeerOutLQRs | read-only | mandatory | Number of lost Link Quality Reports (LQR) transmitted by remote on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.24 | ColumnpppLqmLostPeerOutPkts | read-only | mandatory | Number of lost Packets transmitted by remote on this link. |
| 1.3.6.1.4.1.272.4.3.6.1.25 | ColumnpppLqmLostPeerOutOcts | read-only | mandatory | Number of lost Octets transmitted by remote on this link. |
| 1.3.6.1.4.1.272.4.3.9 | TablepppExtIfTable | not-accessible | mandatory | The pppExtIfTable contains extended configuration and information related to the PPP interfaces on the system. Entries are created and deleted due to the exist… |
| 1.3.6.1.4.1.272.4.3.9.1 | RowpppExtIfEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.3.9.1.1 | ColumnpppExtIfIndex | read-only | mandatory | Correlating PPP interface index. |
| 1.3.6.1.4.1.272.4.3.9.1.2 | ColumnpppExtIfBodMode | read-write | mandatory | Enables bandwidth on demand (BOD) mode for leased line and dialup interfaces when setting to bod-active (3) respectively bod-passive (4) or backup only mode fo… |
| 1.3.6.1.4.1.272.4.3.9.1.3 | ColumnpppExtIfAlgorithm | read-write | mandatory | The algorithm to use for weighting line utilization. Line utilization is determined by calculating the average load for each interface. When set to equal (1) a… |
| 1.3.6.1.4.1.272.4.3.9.1.4 | ColumnpppExtIfInterval | read-write | mandatory | The time interval (in seconds) to use for sampling and calculating of the average throughput of the interface. See also: pppExtIfLoad. |
| 1.3.6.1.4.1.272.4.3.9.1.5 | ColumnpppExtIfLoad | read-only | mandatory | The actual throughput (in percent) of the total bandwidth of this interface (load). This value is updated once every second and based on the amount of traffic … |
| 1.3.6.1.4.1.272.4.3.9.1.6 | ColumnpppExtIfMlpFragmentation | read-write | mandatory | The multilink PPP fragmentation mode. When set to proportional (1) packets will be divided into fragments proportional to the transmission rate of each link, w… |
| 1.3.6.1.4.1.272.4.3.9.1.7 | ColumnpppExtIfMlpFragSize | read-write | mandatory | The multilink PPP fragment size. If MlpFragmentation is set to proportional (1) this value specifies the minimum size of the fragment in bytes. If MlpFragmenta… |
| 1.3.6.1.4.1.272.4.3.9.1.8 | ColumnpppExtIfPPPoEService | read-write | mandatory | The PPPoE (PPP over Ethernet, RFC 2516) service name which indicates the requested service during PPPoE discovery stage. Examples of the use of the service nam… |
| 1.3.6.1.4.1.272.4.3.9.1.9 | ColumnpppExtIfPPPoEAcServer | read-write | mandatory | The PPPoE (PPP over Ethernet, RFC 2516) AC-Server name which determines the access concentrator during PPPoE discovery stage. |
| 1.3.6.1.4.1.272.4.3.9.1.10 | ColumnpppExtIfEncKeyNegotiation | read-write | mandatory | This variable defines the specification of shared secrets (encryption keys) between the sender and receiver of encrypted data. If set to static (1), the keys s… |
| 1.3.6.1.4.1.272.4.3.9.1.11 | ColumnpppExtIfEncTxKey | read-write | mandatory | Static (encryption) key used for transmission of encrypted data via PPP. It's size depends on the used encryption algorithm and the corresponding key length, e… |
| 1.3.6.1.4.1.272.4.3.9.1.12 | ColumnpppExtIfEncRxKey | read-write | mandatory | Static (decryption) key used for decryption of encrypted data received on PPP connections. It's size depends on the used encryption algorithm and the correspon… |
| 1.3.6.1.4.1.272.4.3.9.1.13 | ColumnpppExtIfGearUpThreshold | read-write | mandatory | Gear up threshold for invoking current bandwidth. The measured throughput (in percent of the total bandwidth) of this interface (see pppExtIfLoad) is compared … |
| 1.3.6.1.4.1.272.4.3.9.1.14 | ColumnpppExtIfGearDownThreshold | read-write | mandatory | Gear down threshold for decreasing current bandwidth. The expected throughput (in percent of the total bandwidth) of this interface (see pppExtIfLoad) after dr… |
| 1.3.6.1.4.1.272.4.3.9.1.15 | ColumnpppExtIfAodiDChanQlen | read-write | mandatory | Upper threshold for the amount of data (in octets) waiting to be sent across the 9.6Kbit/sec D-channel. If exceeded, additional bandwidth will be invoked at on… |
| 1.3.6.1.4.1.272.4.3.9.1.16 | ColumnpppExtIfAodiGearDownTxRate | read-write | mandatory | Lower threshold for the amount of data in bits per second to be sent across the 64Kbit/sec B-channel. If the measured throughput becomes smaller than this valu… |
| 1.3.6.1.4.1.272.4.3.9.1.17 | ColumnpppExtIfGearUpPersistance | read-write | mandatory | Gear up persistence interval for invoking current bandwidth. The measured throughput (in percent of the total bandwidth) of this interface (see pppExtIfLoad) i… |
| 1.3.6.1.4.1.272.4.3.9.1.18 | ColumnpppExtIfGearDownPersistance | read-write | mandatory | Gear down persistence interval for decreasing current bandwidth. The measured throughput (in percent of the total bandwidth) of this interface (see pppExtIfLoa… |
| 1.3.6.1.4.1.272.4.3.9.1.19 | ColumnpppExtIfL1Speed | read-write | mandatory | This object contains the interface's nominal bandwidth in bits per second. Please note that this parameter may not represent the real available transmission ra… |
| 1.3.6.1.4.1.272.4.3.9.1.20 | ColumnpppExtIfCurrentRetryTime | read-write | mandatory | Current time in seconds to wait before retrying a call when the smart retry algorithm is implemented. |
| 1.3.6.1.4.1.272.4.3.9.1.21 | ColumnpppExtIfMaxRetryTime | read-write | mandatory | Maximum time in seconds to wait before retrying a call when the smart retry algorithm is implemented. When set to zero this algorithm is disabled. |
| 1.3.6.1.4.1.272.4.3.9.1.22 | ColumnpppExtIfMtu | read-write | mandatory | Determines size of the largest datagram which can be sent on the interface, specified in octets (see ifMtu). When set to zero (default), the value of the varia… |
| 1.3.6.1.4.1.272.4.3.9.1.23 | ColumnpppExtIfMru | read-write | mandatory | The maximum length for the PPP information field, including padding, but not including the protocol field, is termed the Maximum Receive Unit (MRU). |
| 1.3.6.1.4.1.272.4.3.9.1.24 | ColumnpppExtIfAuthMutual | read-write | mandatory | This object enables mutual PPP authentication between the peers. |
| 1.3.6.1.4.1.272.4.3.9.1.26 | ColumnpppExtIfDialProfileIndex | read-write | mandatory | References the associated dial profile. |
| 1.3.6.1.4.1.272.4.3.9.1.27 | ColumnpppExtIfDialinL1Protocol | read-write | mandatory | This variable determines the permitted layer 1 protocol for incoming calls. If set to all(31) there is no specific restriction. In all other cases incoming cal… |
| 1.3.6.1.4.1.272.4.3.9.1.28 | ColumnpppExtIfpppoeEthIfIndex | read-write | mandatory | Determines the Ethernet interface to be used for PPP over Ethernet (PPPoE) according RFC 2516. If not specified here the value in biboPPPProfilePPPoEDevIfIndex… |
| 1.3.6.1.4.1.272.4.3.9.1.29 | ColumnpppExtIfpppoaPvcIfIndex | read-write | mandatory | Determines the ATM PVC to be used for PPP over Ethernet (PPPoA) according RFC 2364 - PPPoA on demand mode. If not specified here the first ATM PVC configured f… |
| 1.3.6.1.4.1.272.4.3.9.1.30 | ColumnpppExtIfRadiusMarkAcct | read-write | mandatory | Determines wether start or stop of RADIUS accounting should be marked (via Accounting-On/Accounting-Off) for the logical RADIUS server group specified by pppEx… |
| 1.3.6.1.4.1.272.4.3.9.1.31 | ColumnpppExtIfRadiusGroupId | read-write | mandatory | Determines the logical RADIUS server group to be addressed for sending the RADIUS Accounting-On/Accounting-Off messages. See also radiusSrvPriority. |
| 1.3.6.1.4.1.272.4.3.10 | TablepppSessionTable | not-accessible | mandatory | The pppSessionTable contains statistical information for the PPP protocol. Only the system can add or delete entries to this table. Creating entries: Entries a… |
| 1.3.6.1.4.1.272.4.3.10.1 | RowpppSessionEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.3.10.1.1 | ColumnpppSessionIfIndex | read-only | mandatory | Correlating PPP interface index. |
| 1.3.6.1.4.1.272.4.3.10.1.2 | ColumnpppSessionMlp | read-only | mandatory | Indicates negotiation of Multilink PPP. |
| 1.3.6.1.4.1.272.4.3.10.1.3 | ColumnpppSessionMru | read-only | mandatory | Peer's MRU/MRRU LCP option. |
| 1.3.6.1.4.1.272.4.3.10.1.4 | ColumnpppSessionLcpCallback | read-only | mandatory | Callback option inside LCP negotiation. |
| 1.3.6.1.4.1.272.4.3.10.1.5 | ColumnpppSessionAuthProt | read-only | mandatory | The negotiated PPP authentication protocol. |
| 1.3.6.1.4.1.272.4.3.10.1.6 | ColumnpppSessionCompression | read-only | mandatory | The negotiated CCP compression mode. |
| 1.3.6.1.4.1.272.4.3.10.1.7 | ColumnpppSessionEncryption | read-only | mandatory | The negotiated CCP encryption mode. |
| 1.3.6.1.4.1.272.4.3.10.1.8 | ColumnpppSessionCbcpMode | read-only | mandatory | The negotiated Callback Control Protocol (CBCP) mode. |
| 1.3.6.1.4.1.272.4.3.10.1.9 | ColumnpppSessionCbcpDelay | read-only | mandatory | The negotiated (CBCP) callback delay in seconds. |
| 1.3.6.1.4.1.272.4.3.10.1.10 | ColumnpppSessionLocIpAddr | read-only | mandatory | The negotiated local IP Address. |
| 1.3.6.1.4.1.272.4.3.10.1.11 | ColumnpppSessionRemIpAddr | read-only | mandatory | The negotiated remote IP Address. |
| 1.3.6.1.4.1.272.4.3.10.1.12 | ColumnpppSessionDNS1 | read-only | mandatory | The negotiated first name server IP address. |
| 1.3.6.1.4.1.272.4.3.10.1.13 | ColumnpppSessionDNS2 | read-only | mandatory | The negotiated second name server IP address. |
| 1.3.6.1.4.1.272.4.3.10.1.14 | ColumnpppSessionWINS1 | read-only | mandatory | The negotiated first NetBIOS name server (WINS) IP address. |
| 1.3.6.1.4.1.272.4.3.10.1.15 | ColumnpppSessionWINS2 | read-only | mandatory | The negotiated second NetBIOS name server (WINS) IP address. |
| 1.3.6.1.4.1.272.4.3.10.1.16 | ColumnpppSessionVJHeaderComp | read-only | mandatory | The negotiation of Van Jacobsen TCP/IP header compression option (IPCP). |
| 1.3.6.1.4.1.272.4.3.10.1.18 | ColumnpppSessionBacpFavoredPeer | read-only | mandatory | The result of the BACP Favored-Peer negotiation. |
| 1.3.6.1.4.1.272.4.3.10.1.19 | ColumnpppSessionIpcpStatus | read-only | mandatory | IPCP FSM status according RFC 1548. |
| 1.3.6.1.4.1.272.4.3.11 | TablepppDialProfileTable | not-accessible | mandatory | The pppDialProfileTable contains default parameters used for establishing dialout connections in cases where there is no partner specific configuration availab… |
| 1.3.6.1.4.1.272.4.3.11.1 | RowpppDialProfileEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.3.11.1.1 | ColumnpppDialProfileIndex | read-only | mandatory | This object uniquely references this dialout profile. The index value is generated automatically. |
| 1.3.6.1.4.1.272.4.3.11.1.2 | ColumnpppDialProfileDescr | read-write | mandatory | A textual string describing this dialout profile. |
| 1.3.6.1.4.1.272.4.3.11.1.3 | ColumnpppDialProfileBapNumber | read-write | mandatory | This object decribes the phone delta to use in a BAP Call-Response or Callback-Request according RFC 2125. |
| 1.3.6.1.4.1.272.4.3.11.1.4 | ColumnpppDialProfileBapSubAddress | read-write | mandatory | This object decribes the subaddress to use in a BAP Call-Response or Callback-Request according RFC 2125. |
| 1.3.6.1.4.1.272.4.3.11.1.5 | ColumnpppDialProfileBapLkType | read-write | mandatory | This object describes the link type to use in a BAP Call-Response or Callback-Request according RFC 2125. |
| 1.3.6.1.4.1.272.4.3.11.1.6 | ColumnpppDialProfileStkMask | read-write | mandatory | This binary number defines the ISDN stack(s) to use. Each bit corresponds to one entry (stack) in the isdnStkTable, the rightmost bit selects entry 0, the next… |
| 1.3.6.1.4.1.272.4.3.11.1.7 | ColumnpppDialProfileCallbackL1Prot | read-write | mandatory | This entry is used to select the layer 1 protocol settings for callback. if set to initial(1), the selected layer 1 protocol of the initial call will be used t… |
| 1.3.6.1.4.1.272.4.3.13 | TablepppLinkHistoryTable | not-accessible | mandatory | The pppLinkHistoryTable contains statistical information for each closed PPP link on the system. Only the system can add or delete entries to this table. Creat… |
| 1.3.6.1.4.1.272.4.3.13.1 | RowpppLinkHistoryEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.3.13.1.1 | ColumnpppLinkHistIfIndex | read-only | mandatory | Correlating PPP interface index. |
| 1.3.6.1.4.1.272.4.3.13.1.2 | ColumnpppLinkHistId | read-only | mandatory | Unique ID for this entry. |
| 1.3.6.1.4.1.272.4.3.13.1.3 | ColumnpppLinkHistCreated | read-only | mandatory | Time when this entry was created. |
| 1.3.6.1.4.1.272.4.3.13.1.4 | ColumnpppLinkHistDirection | read-only | mandatory | Direction of link, incoming(1) or outgoing(2). In case of permanent links, the meaning is dce(1) or dte(2). |
| 1.3.6.1.4.1.272.4.3.13.1.9 | ColumnpppLinkHistAccm | read-only | mandatory | The Asynchronous Control Character Map (ACCM) according RFC 1662. |
| 1.3.6.1.4.1.272.4.3.13.1.10 | ColumnpppLinkHistLqm | read-only | mandatory | Indicates the successful negotiation of the Link Quality Protocol (LQM). |
| 1.3.6.1.4.1.272.4.3.13.1.11 | ColumnpppLinkHistLcpComp | read-only | mandatory | Address- and Protocol-Field compression. |
| 1.3.6.1.4.1.272.4.3.13.1.12 | ColumnpppLinkHistLocDiscr | read-only | mandatory | Local LCP multilink endpoint discriminator. |
| 1.3.6.1.4.1.272.4.3.13.1.13 | ColumnpppLinkHistRemDiscr | read-only | mandatory | Peer's LCP multilink endpoint discriminator. |
| 1.3.6.1.4.1.272.4.3.13.1.14 | ColumnpppLinkHistLocAuth | read-only | mandatory | The result of the PPP authentication procedure performed locally. |
| 1.3.6.1.4.1.272.4.3.13.1.15 | ColumnpppLinkHistRemAuth | read-only | mandatory | The result of the PPP authentication procedure performed on remote. |
| 1.3.6.1.4.1.272.4.3.13.1.17 | ColumnpppLinkHistL1Protocol | read-only | mandatory | The layer 1 protocol of this link. |
| 1.3.6.1.4.1.272.4.3.14 | ScalarpppLinkHistoryMaxEntries | read-write | mandatory | Maximum number of pppLinkHistory entries in memory. |
| 1.3.6.1.4.1.272.4.3.15 | TablepppPppoeEthDevTable | not-accessible | mandatory | . |
| 1.3.6.1.4.1.272.4.3.15.1 | RowpppPppoeEthDevEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.3.15.1.1 | ColumnpppPppoeEthDevIfIndex | read-write | mandatory | The associated interface index of this entry. |
| 1.3.6.1.4.1.272.4.3.15.1.2 | ColumnpppPppoeEthDevAdminStatus | read-write | mandatory | The administrative this entry. |
| 1.3.6.1.4.1.272.4.3.15.1.3 | ColumnpppPppoeEthDevIndex | read-write | mandatory | Specifies the first device to be used for PPP over Ethernet (PPPoE) according RFC 2516. |
| 1.3.6.1.4.1.272.4.3.15.1.4 | ColumnpppPppoeEthDevMaxTxRate | read-write | mandatory | Administrative transmit rate limitation needed in order to support scenarios with external XDSL modems. If specified this value will be adopted in associated b… |
| 1.3.6.1.4.1.272.4.3.15.1.10 | ColumnpppPppoeEthDevOperStatus | read-only | mandatory | The PPP-internal operational status of the first device to be used for PPP over Ethernet (PPPoE) according RFC 2516. |
| 1.3.6.1.4.1.272.4.3.15.1.11 | ColumnpppPppoeEthDevResidualBlockTime | read-only | mandatory | The remaining time interval till the associated pppPppoeEthDevOperStatus will be changed from blocked(4) to dormant(1) again. |
| 1.3.6.1.4.1.272.4.3.16 | TablemlpppStatTable | not-accessible | mandatory | The mlpppStatTable contains statistical multilink specific information. Only the system can add or delete entries to this table. Creating entries: Entries are … |
| 1.3.6.1.4.1.272.4.3.16.1 | RowmlpppStatEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.3.16.1.1 | ColumnmlpppIfIndex | read-only | mandatory | Correlating PPP interface index. |
| 1.3.6.1.4.1.272.4.3.16.1.2 | ColumnmlpppNextTxSeqno | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.3.16.1.3 | ColumnmlpppLastRxSeqno | read-only | mandatory | |
| 1.3.6.1.4.1.272.4.3.16.1.4 | ColumnmlpppMaxFragCount | read-only | mandatory | Maximum size (number of Fragments) of MLPPP reassembling area. |
| 1.3.6.1.4.1.272.4.3.16.1.5 | ColumnmlpppMaxFragLifeTime | read-only | mandatory | Maximum lifetime of fragments stored in MLPPP reassembling area. |
| 1.3.6.1.4.1.272.4.3.16.1.6 | ColumnmlpppFragsRcvd | read-only | mandatory | Total number of MLPPP fragments received since interface is in operational 'up' status. |
| 1.3.6.1.4.1.272.4.3.16.1.7 | ColumnmlpppFragsQueued | read-only | mandatory | Current number of MLPPP fragments stored in MLPPP reassembling area. |
| 1.3.6.1.4.1.272.4.3.16.1.8 | ColumnmlpppFragsDropped | read-only | mandatory | Total number of MLPPP fragments dropped since interface is in operational 'up' status. |
| 1.3.6.1.4.1.272.4.3.16.1.9 | ColumnmlpppPktsReassembled | read-only | mandatory | Total number pakets reassembled since interface is in operational 'up' status. |
| 1.3.6.1.4.1.272.4.3.16.1.10 | ColumnmlpppBeginOfQueue | read-only | mandatory | Sequence Number of first fragment stored in MLPPP reassembling area. |
| 1.3.6.1.4.1.272.4.3.16.1.11 | ColumnmlpppEndOfQueue | read-only | mandatory | Sequence Number of last fragment stored in MLPPP reassembling area. |
| 1.3.6.1.4.1.272.4.3.16.1.12 | ColumnmlpppBFragsQueued | read-only | mandatory | Current number (begin-)fragments stored in MLPPP reassembling area. |
| 1.3.6.1.4.1.272.4.3.16.1.13 | ColumnmlpppEFragsQueued | read-only | mandatory | Current number (end-)fragments stored in MLPPP reassembling area. |
| 1.3.6.1.4.1.272.4.3.16.1.14 | ColumnmlpppMFragsQueued | read-only | mandatory | Current number (middle-)fragments stored in MLPPP reassembling area. |
| 1.3.6.1.4.1.272.4.3.16.1.15 | ColumnmlpppCFragsQueued | read-only | mandatory | Current number (complete-)fragments stored in MLPPP reassembling area. |
| 1.3.6.1.4.1.272.4.3.16.1.16 | ColumnmlpppAgeDrops | read-only | mandatory | Total number fragments dropped due to exceeded lifetime, see also mlpppMaxFragLifeTime. |
| 1.3.6.1.4.1.272.4.3.16.1.17 | ColumnmlpppOutOfSyncDrops | read-only | mandatory | Total number fragments dropped due to a 'out of sync' condition. |
| 1.3.6.1.4.1.272.4.3.16.1.18 | ColumnmlpppOverFlowDrops | read-only | mandatory | Total number fragments dropped due to a MLPPP reassembling area 'overflow' condition, see also mlpppMaxFragCount. |
| 1.3.6.1.4.1.272.4.3.16.1.19 | ColumnmlpppDuplicateDrops | read-only | mandatory | Total number duplicate fragments dropped. |
| 1.3.6.1.4.1.272.4.3.16.1.20 | ColumnmlpppForwardDeviation | read-only | mandatory | Maximum deviation of current received sequence number compared with the end of the reassembling queue in forward direction. |
| 1.3.6.1.4.1.272.4.3.16.1.21 | ColumnmlpppBackwardDeviation | read-only | mandatory | Maximum deviation of current received sequence number compared with the begin of the reassembling queue in backward direction. |
| 1.3.6.1.4.1.272.4.3.16.1.22 | ColumnmlpppNextReasSeqNo | read-only | mandatory | Awaited first sequence number of next the fragment chain or packet ready to be distributed to the upper layer. |
| 1.3.6.1.4.1.272.4.3.16.1.23 | ColumnmlpppOutOfOrderWaits | read-only | mandatory | Number of cycles already reassembled packets are retained due to the expected mlpppNextReasSeqNo value. |
| 1.3.6.1.4.1.272.4.3.16.1.24 | ColumnmlpppMaxReasBurst | read-only | mandatory | Maximum number of reassembled packets sended to the upper layer within one cycle. |
| 1.3.6.1.4.1.272.4.3.16.1.25 | ColumnmlpppCleanupDrops | read-only | mandatory | Number of fragments dropped cause they were still in in the queue when interface went down. |
| 1.3.6.1.4.1.272.4.3.17 | TablebiboPPPIpPoolTable | not-accessible | mandatory | The biboPPPIpPoolTable contains IP addresses used when dynamically assigning IP addresses; i.e. when the biboPPPIpAddress field is set to `dynamic'. Creating e… |
| 1.3.6.1.4.1.272.4.3.17.1 | RowbiboPPPIpPoolEntry | not-accessible | mandatory | Pool of IP addresses for dynamic IP address assignment via IPCP. See the biboPPPIpAddress field for further explanation. |
| 1.3.6.1.4.1.272.4.3.17.1.1 | ColumnbiboPPPIpPoolIdentifier | read-write | mandatory | The ID of the responding dynamic pool. |
| 1.3.6.1.4.1.272.4.3.17.1.2 | ColumnbiboPPPIpPoolAdminStatus | read-write | mandatory | If the AdminStatus is set to enabled(1) this entry will be used. Setting it to disabled(2) this entry won't be used . You may also delete this entry by changin… |
| 1.3.6.1.4.1.272.4.3.17.1.3 | ColumnbiboPPPIpPoolMode | read-write | mandatory | The IpPoolMode tries to reassign the IP Address a client had before if it is in recover(1) Mode. Otherwise (2) an unassigned IP Address of the PPP dynamic IP P… |
| 1.3.6.1.4.1.272.4.3.18 | TablepppPppoaPvcDevTable | not-accessible | mandatory | . |
| 1.3.6.1.4.1.272.4.3.18.1 | RowpppPppoaPvcDevEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.3.18.1.1 | ColumnpppPppoaPvcDevIfIndex | read-write | mandatory | The associated interface index of this entry. |
| 1.3.6.1.4.1.272.4.3.18.1.2 | ColumnpppPppoaPvcDevAdminStatus | read-write | mandatory | The administrative this entry. |
| 1.3.6.1.4.1.272.4.3.18.1.3 | ColumnpppPppoaPvcDevIndex | read-write | mandatory | Specifies the first device to be used for PPP over ATM (PPPoA) according RFC 2364. |
| 1.3.6.1.4.1.272.4.3.18.1.10 | ColumnpppPppoaPvcDevOperStatus | read-only | mandatory | The PPP-internal operational status of the first device to be used for PPP over ATM (PPPoA) according RFC 2364. |
| 1.3.6.1.4.1.272.4.3.18.1.11 | ColumnpppPppoaPvcDevResidualBlockTime | read-only | mandatory | The remaining time interval till the associated pppPppoaPvcDevOperStatus will be changed from blocked(4) to dormant(1) again. |
| 1.3.6.1.4.1.272.4.4 | Nodedialmap | |||
| 1.3.6.1.4.1.272.4.4.1 | TablebiboDialTable | not-accessible | mandatory | The biboDialTable contains configuration information for incoming and outgoing ISDN telephone numbers. Creating entries: Entries are created by assigning a val… |
| 1.3.6.1.4.1.272.4.4.1.1 | RowbiboDialEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.4.1.1.1 | ColumnbiboDialIfIndex | read-write | mandatory | The correlating PPP interface index. |
| 1.3.6.1.4.1.272.4.4.1.1.2 | ColumnbiboDialType | read-write | mandatory | The dialup type can be set to plain isdn(1), isdn-spv(2) semi-permanent links used by the German 1TR6 D-channel protocol, or to delete(3) to delete a biboDialT… |
| 1.3.6.1.4.1.272.4.4.1.1.3 | ColumnbiboDialDirection | read-write | mandatory | The allowed dial direction is either incoming(1), outgoing(2), or both(3) calls. No call is ever set up when set to incoming(1). Incoming calls will not be ide… |
| 1.3.6.1.4.1.272.4.4.1.1.4 | ColumnbiboDialNumber | read-write | mandatory | The defined dialing number. Used for either dialing or comparing to incoming calls or both, depending on the content of the biboDialDirection field. The wildca… |
| 1.3.6.1.4.1.272.4.4.1.1.5 | ColumnbiboDialSubaddress | read-write | mandatory | The defined dial subaddress, if any. Also, see the biboDialNumber field. |
| 1.3.6.1.4.1.272.4.4.1.1.6 | ColumnbiboDialClosedUserGroup | read-write | mandatory | The defined closed user group, if any. Also, see the biboDialNumber field. |
| 1.3.6.1.4.1.272.4.4.1.1.7 | ColumnbiboDialStkMask | read-write | mandatory | The defined stack mask. Each value of IsdnStkNumber represents a bit in this bitmask. A mask of 0 disables dialup completely, while a mask of -1 enables dialup… |
| 1.3.6.1.4.1.272.4.4.1.1.8 | ColumnbiboDialScreening | read-write | mandatory | The screening indicator of the biboDialNumber. The biboDialScreening field can be used to gauge the `trustworthiness' of the biboDialNumber field. (See isdnCal… |
| 1.3.6.1.4.1.272.4.4.1.1.9 | ColumnbiboDialCallingSubaddress | read-write | mandatory | The defined calling dial subaddress, if any. Also, see the biboDialNumber field. |
| 1.3.6.1.4.1.272.4.4.1.1.10 | ColumnbiboDialTypeOfCallingSubAdd | read-write | mandatory | The type of calling party subaddress. |
| 1.3.6.1.4.1.272.4.4.1.1.11 | ColumnbiboDialTypeOfCalledSubAdd | read-write | mandatory | The type of called party subaddress. |
| 1.3.6.1.4.1.272.4.4.1.1.12 | ColumnbiboDialLocalNumber | read-write | mandatory | The defined local dialing number. Used as originator address in the case of an outgoing calling and is checked against the destination address in the case of a… |
| 1.3.6.1.4.1.272.4.4.1.1.13 | ColumnbiboDialTypeOfLocalNumber | read-write | mandatory | The type of local number (biboDialLocalNumber) upon outgoing calls according to ETS 300 102-1. Possible values are: unknown(1), international-number(2), nation… |
| 1.3.6.1.4.1.272.4.4.1.1.14 | ColumnbiboDialOutNumTranslation | read-write | mandatory | If DialOutNumTranslation is disabled, the number will be passed to the lower layers without modification. |