BIANCA-BRICK-WIRELESS-MIB
676 objects
MIB for wlan subsystem
Imported Objects
| BINTEC-MIB MISSING | bibo BitValue Date HexValue wlan |
| IF-MIB | ifIndex |
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | enterprises IpAddress |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 MODULE-IDENTITY NOTIFICATION-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DisplayString MacAddress RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.45.8.1.1 | TablewlanIfTable | not-accessible | current | The wlanIfTable contains information relating to the interfaces available on the system. Each entry corresponds to an available WLAN interface. Entries cannot … |
| 1.3.6.1.4.1.45.8.1.1.1 | RowwlanIfEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.1.1.1 | ColumnwlanIfIndex | read-only | current | Unique radio index. |
| 1.3.6.1.4.1.45.8.1.1.1.2 | ColumnwlanIfType | read-write | current | The WLAN physical interface type off(1) interface disabled access-point(2) access point client(3) client mode wds-only(4) wireless distribution system |
| 1.3.6.1.4.1.45.8.1.1.1.3 | ColumnwlanIfMode | read-write | current | Mixed and compatibility modes between various 802.11 substandards.. |
| 1.3.6.1.4.1.45.8.1.1.1.4 | ColumnwlanIfSpeed | read-write | current | The value defines the bitrate or the coding scheme to use for data frames. auto(31) enables automatic rate adaption. |
| 1.3.6.1.4.1.45.8.1.1.1.5 | ColumnwlanIfChannel | read-write | current | The physical channel |
| 1.3.6.1.4.1.45.8.1.1.1.6 | ColumnwlanIfRtsThreshold | read-write | current | This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed, except as RTS/CTS is used as a cross mo… |
| 1.3.6.1.4.1.45.8.1.1.1.7 | ColumnwlanIfRxThreshold | read-write | current | |
| 1.3.6.1.4.1.45.8.1.1.1.8 | ColumnwlanIfTxPower | read-write | current | Transmitter output power in dBm. |
| 1.3.6.1.4.1.45.8.1.1.1.9 | ColumnwlanIfAntennaRx | read-write | current | The current antenna being used to receive. |
| 1.3.6.1.4.1.45.8.1.1.1.10 | ColumnwlanIfAntennaTx | read-write | current | The current antenna being used to transmit. |
| 1.3.6.1.4.1.45.8.1.1.1.11 | ColumnwlanIfAntennaDiversity | read-write | current | |
| 1.3.6.1.4.1.45.8.1.1.1.12 | ColumnwlanIfTimeout | read-write | current | Station Timeout in minutes. |
| 1.3.6.1.4.1.45.8.1.1.1.13 | ColumnwlanIfBurst | read-write | current | Sending wireless frames without backoff time. |
| 1.3.6.1.4.1.45.8.1.1.1.16 | ColumnwlanIfCountry | read-write | current | This attribute identifies the country in which the station is operating. The first two octets of this string is the two character country code as described in … |
| 1.3.6.1.4.1.45.8.1.1.1.17 | ColumnwlanIfAddress | read-only | current | The MAC Address of the AP |
| 1.3.6.1.4.1.45.8.1.1.1.19 | ColumnwlanIfBand | read-write | current | Frequency band |
| 1.3.6.1.4.1.45.8.1.1.1.20 | ColumnwlanIfAckWindow | read-write | current | Additional 802.11 ACK timeout in microseconds. This must be set to non-zero value for radio distances larger than about 700m. Recommended setting is about 10 m… |
| 1.3.6.1.4.1.45.8.1.1.1.21 | ColumnwlanIfRealChannel | read-only | current | The actually selected channel for transmit and receive. In most cases this is the same value as wlanIfChannel, except if automatic channel selection is active.… |
| 1.3.6.1.4.1.45.8.1.1.1.22 | ColumnwlanIfCWmin | read-write | current | Minimum size of contention window. See also 9.2.4 of IEEE 802.11. This value must be a power of 2 minus 1. |
| 1.3.6.1.4.1.45.8.1.1.1.23 | ColumnwlanIfCWmax | read-write | current | Maximum size of contention window. See also 9.2.4 of IEEE 802.11. This value must be a power of 2 minus 1. |
| 1.3.6.1.4.1.45.8.1.1.1.25 | ColumnwlanIfPerfOptions | read-write | current | This attribute holds a collection of radio-dependant, proprietary performance enhancement options. Currently defined options are: nitroXMFrameCompression(0) Th… |
| 1.3.6.1.4.1.45.8.1.1.1.26 | ColumnwlanIfStaTimeout | read-write | current | Number of seconds without any incoming traffic before associated STAs are polled for presence. If the STA fails to respond to wlanIfStaMaxPolls consecutive pol… |
| 1.3.6.1.4.1.45.8.1.1.1.27 | ColumnwlanIfStaMaxPolls | read-write | current | Number of times associated STAs are polled for presence. If the STA fails to respond to wlanIfStaMaxPolls consecutive polls, it will be forcefully disassociate… |
| 1.3.6.1.4.1.45.8.1.1.1.28 | ColumnwlanIfWMMParam | read-write | current | WWM status 1=enable, 2=disable, access category parameters could be changed in wLanWMMTable. |
| 1.3.6.1.4.1.45.8.1.1.1.29 | ColumnwlanIfSkipChannels24Ghz | read-write | current | If a bit is set the accordingly channel will be skipped from the channel scan list (channel 1-14 for 2.4 GHz). Default is scan all channels. |
| 1.3.6.1.4.1.45.8.1.1.1.30 | ColumnwlanIfSkipChannels5Ghz | read-write | current | If a bit is set the accordingly channel will be skipped from the channel scan list (channel 36-173 for 5 GHz). Default is scan all channels. |
| 1.3.6.1.4.1.45.8.1.1.1.65 | ColumnwlanIfRxPackets | read-only | current | |
| 1.3.6.1.4.1.45.8.1.1.1.66 | ColumnwlanIfRxBytes | read-only | current | |
| 1.3.6.1.4.1.45.8.1.1.1.67 | ColumnwlanIfRxErrors | read-only | current | |
| 1.3.6.1.4.1.45.8.1.1.1.68 | ColumnwlanIfRxDecryptionError | read-only | current | |
| 1.3.6.1.4.1.45.8.1.1.1.69 | ColumnwlanIfRxRejected | read-only | current | |
| 1.3.6.1.4.1.45.8.1.1.1.70 | ColumnwlanIfTxPackets | read-only | current | |
| 1.3.6.1.4.1.45.8.1.1.1.71 | ColumnwlanIfTxBytes | read-only | current | |
| 1.3.6.1.4.1.45.8.1.1.1.72 | ColumnwlanIfTxErrors | read-only | current | |
| 1.3.6.1.4.1.45.8.1.1.1.73 | ColumnwlanIfTxDropped | read-only | current | |
| 1.3.6.1.4.1.45.8.1.1.1.74 | ColumnwlanIfMSDUTxErrors | read-only | current | |
| 1.3.6.1.4.1.45.8.1.1.1.75 | ColumnwlanIfMSDURxErrors | read-only | current | |
| 1.3.6.1.4.1.45.8.1.1.1.76 | ColumnwlanIfAssociated | read-only | current | |
| 1.3.6.1.4.1.45.8.1.1.1.77 | ColumnwlanIfOperState | read-only | current | This attribute reflects the operational state of the corresponding WLAN card. |
| 1.3.6.1.4.1.45.8.1.1.1.81 | ColumnwlanIfNoise | read-only | current | This attribute shows the measured noise level in dBm, or 0 when this value is not available. It's the value measured during the last reception of data. |
| 1.3.6.1.4.1.45.8.1.1.1.82 | ColumnwlanIfRadioNumber | read-only | current | Radio number used in user interfaces and for labeling. |
| 1.3.6.1.4.1.45.8.1.2 | TablewlanVSSTable | not-accessible | current | Describes a WLAN VSS and the correspondending settings |
| 1.3.6.1.4.1.45.8.1.2.1 | RowwlanVSSEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.2.1.1 | ColumnwlanVSSIndex | read-only | current | Unique VSS index of an Broadcast VSS. |
| 1.3.6.1.4.1.45.8.1.2.1.3 | ColumnwlanVSSIfIndex | read-only | current | ifIndex for this service set. |
| 1.3.6.1.4.1.45.8.1.2.1.4 | ColumnwlanVSSwlanIf | read-write | current | Radio index the VSS belongs to. |
| 1.3.6.1.4.1.45.8.1.2.1.5 | ColumnwlanVSSId | read-write | current | This attribute reflects the Service Set ID used in the DesiredSSID parameter of the most recent MLME_Scan.request. |
| 1.3.6.1.4.1.45.8.1.2.1.6 | ColumnwlanVSSAdminStatus | read-write | current | Enable or disable the requested VSS. |
| 1.3.6.1.4.1.45.8.1.2.1.7 | ColumnwlanVSSSecurity | read-write | current | The Security Option which will be used. wep40 and wep104:= WEP-Authentication wpa-psk := WPA-Authentication with PSK wpa := WPA-Authentication with radius (802… |
| 1.3.6.1.4.1.45.8.1.2.1.10 | ColumnwlanVSSPolicies | read-write | current | The Policies of the Broadcast VSS. Applicable: DOT11_MLMEPOLICY_PRIVACYREQUIRED DOT11_MLMEPOLICY_PRIVACYCAPABILITY DOT11_MLMEPOLICY_ALLOWUNENCRYPTEDBCAST DOT11… |
| 1.3.6.1.4.1.45.8.1.2.1.11 | ColumnwlanVSSInvoked | read-write | current | The Privacy Invoke Setting |
| 1.3.6.1.4.1.45.8.1.2.1.12 | ColumnwlanVSSExunencrypted | read-write | current | The Privacy Invoke Setting |
| 1.3.6.1.4.1.45.8.1.2.1.13 | ColumnwlanVSSDefaultKey | read-write | current | Default key for WEP encryption. |
| 1.3.6.1.4.1.45.8.1.2.1.14 | ColumnwlanVSSKey1 | read-write | current | Key string for WEP key no. 1. Also used for WPA passphrase |
| 1.3.6.1.4.1.45.8.1.2.1.15 | ColumnwlanVSSKey2 | read-write | current | Key string for WEP key no. 2. |
| 1.3.6.1.4.1.45.8.1.2.1.16 | ColumnwlanVSSKey3 | read-write | current | Key string for WEP key no. 3. |
| 1.3.6.1.4.1.45.8.1.2.1.17 | ColumnwlanVSSKey4 | read-write | current | Key string for WEP key no. 4. |
| 1.3.6.1.4.1.45.8.1.2.1.18 | ColumnwlanVSSTotal | read-write | current | The number of allowed clients of the requested VSS. |
| 1.3.6.1.4.1.45.8.1.2.1.20 | ColumnwlanVSSMAC | read-write | current | MAC Media Access Control via MAC Address |
| 1.3.6.1.4.1.45.8.1.2.1.21 | ColumnwlanVSSLocal | read-write | current | Routing between connected Clients |
| 1.3.6.1.4.1.45.8.1.2.1.22 | ColumnwlanVSSHidden | read-create | current | Define whether SSID is hidden (yes(2)) or not (no(2)). Default value is 'no(1)'. |
| 1.3.6.1.4.1.45.8.1.2.1.24 | ColumnwlanVSSCurrent | read-only | current | Count of current associated stations |
| 1.3.6.1.4.1.45.8.1.2.1.25 | ColumnwlanVSSMSDUTx | read-only | current | This attribute counts the total number of packets transmitted on this VSS. |
| 1.3.6.1.4.1.45.8.1.2.1.26 | ColumnwlanVSSMSDURx | read-only | current | This attribute counts the total number of packets received by this VSS. |
| 1.3.6.1.4.1.45.8.1.2.1.27 | ColumnwlanVSSBytesTx | read-only | current | Transmitted Bytes |
| 1.3.6.1.4.1.45.8.1.2.1.28 | ColumnwlanVSSBytesRx | read-only | current | Received Bytes |
| 1.3.6.1.4.1.45.8.1.2.1.29 | ColumnwlanVSSWPAMulticastCipher | read-only | current | The multicast ciphers used for WPA. Only one of the following values is allowed: WPA_CIPHERSUITE_NONE(0) WPA_CIPHERSUITE_WEP_40(1) WPA_CIPHERSUITE_WEP_104(2) W… |
| 1.3.6.1.4.1.45.8.1.2.1.30 | ColumnwlanVSSRSNMulticastCipher | read-only | current | The multicast ciphers used for RSN. Only one of the following values is allowed: WPA_CIPHERSUITE_NONE(0) WPA_CIPHERSUITE_WEP_40(1) WPA_CIPHERSUITE_WEP_104(2) W… |
| 1.3.6.1.4.1.45.8.1.2.1.31 | ColumnwlanVSSWPAUnicastCipher | read-write | current | The set of unicast ciphers used for WPA. set one or more of the following bit values: WPA_CIPHERSUITE_NONE(0) WPA_CIPHERSUITE_WEP_40(1) WPA_CIPHERSUITE_WEP_104… |
| 1.3.6.1.4.1.45.8.1.2.1.32 | ColumnwlanVSSRSNUnicastCipher | read-write | current | The set of unicast ciphers used for RSN. set one or more of the following bit values: WPA_CIPHERSUITE_NONE(0) WPA_CIPHERSUITE_WEP_40(1) WPA_CIPHERSUITE_WEP_104… |
| 1.3.6.1.4.1.45.8.1.2.1.34 | ColumnwlanVSSRSNCapabilities | read-only | current | Acccording to IEEE 802.11-2007 Section 7.3.2.25.3: The RSN Capabilities field indicates requested or advertised capabilities. The value of each of the RSN Capa… |
| 1.3.6.1.4.1.45.8.1.2.1.35 | ColumnwlanVSSWpaMixedMode | read-write | current | Allowed mixed operation of WPA and WPA2 by value wpaandwpa2(3) (default value). For tightened security, wpa2(2) can be selected. The value wpa(1) is available … |
| 1.3.6.1.4.1.45.8.1.2.1.36 | ColumnwlanVSSRsnPreauthentication | read-write | current | When this object is set to TRUE, this shall indicate that RSNA preauthentication is enabled on this entity. This object requires that dot11RSNAEnabled also be … |
| 1.3.6.1.4.1.45.8.1.2.1.37 | ColumnwlanVSSBSSID | read-only | current | This object contains the actual current BSSID for the service set. |
| 1.3.6.1.4.1.45.8.1.2.1.38 | ColumnwlanVSSWMMEnabled | read-write | current | This object defines whether WMM (Wi-Fi Multimedia) is active for this service set. Depending on the WLAN hardware and driver, WMM might only be allowed for one… |
| 1.3.6.1.4.1.45.8.1.2.1.39 | ColumnwlanVSSTxMcAirtime | read-only | current | Accumulated estimated time in microseconds for all broadcast/multicast frames transmitted. |
| 1.3.6.1.4.1.45.8.1.2.1.40 | ColumnwlanVSSRxAirtime | read-only | current | Accumulated estimated time in microseconds for all unidirectional frames received from all stations. |
| 1.3.6.1.4.1.45.8.1.2.1.41 | ColumnwlanVSSTxUcAirtime | read-only | current | Accumulated estimated time in microseconds for all unidirectional frames transmitted to all stations. |
| 1.3.6.1.4.1.45.8.1.2.1.42 | ColumnwlanVSSARPProcessing | read-write | current | This object defines whether ARP processing is active for this service set or not. ARP processing is a feature to reduce the number of ARP broadcast packets. If… |
| 1.3.6.1.4.1.45.8.1.2.1.43 | ColumnwlanVSSIgmpSnooping | read-write | current | This object defines the mode off IGMP Snooping. disabled(1) means that IGMP Snooping is off and therefore all multicast is sent out. In mode enabled(2) multica… |
| 1.3.6.1.4.1.45.8.1.3 | TablewlanWDSTable | not-accessible | current | Describe a WLAN WDS and the corresponding settings. |
| 1.3.6.1.4.1.45.8.1.3.1 | RowwlanWDSEntry | not-accessible | current | WDS Link Configuration |
| 1.3.6.1.4.1.45.8.1.3.1.1 | ColumnwlanWDSIndex | read-only | current | Unique index of a WDS link |
| 1.3.6.1.4.1.45.8.1.3.1.2 | ColumnwlanWDSIfIndex | read-only | current | IfIndex of the WDS. |
| 1.3.6.1.4.1.45.8.1.3.1.3 | ColumnwlanWDSwlanIf | read-create | current | IfIndex of the Interface the WDS belongs to. |
| 1.3.6.1.4.1.45.8.1.3.1.4 | ColumnwlanWDSAdminStatus | read-create | current | Enable or disable the requested WDS. |
| 1.3.6.1.4.1.45.8.1.3.1.5 | ColumnwlanWDSAddress | read-create | current | MAC Address of the WDS partner. |
| 1.3.6.1.4.1.45.8.1.3.1.6 | ColumnwlanWDSPrivacyMode | read-create | current | This attribute selects privacy mode to use for a WDS link. Privacy is immediately enabled if anything different from 'none' is selected and an appropriate key … |
| 1.3.6.1.4.1.45.8.1.3.1.7 | ColumnwlanWDSPrivacyAutoKey | read-create | current | Writing any non-zero value to this attribute triggers automatic bridge privacy setup. Depending on wlanWDSPrivacyMode, a pseudo-random WEP key or passphrase is… |
| 1.3.6.1.4.1.45.8.1.3.1.8 | ColumnwlanWDSLinkAliasName | read-create | current | This attribute can be used to set a textual alias name for this bridge link. Default is 'wl?_br?', where first '?' is radio number and second '?' is link numbe… |
| 1.3.6.1.4.1.45.8.1.3.1.9 | ColumnwlanWDSOperStatus | read-only | current | This attribute shows if the bridge link connection is currently operative. |
| 1.3.6.1.4.1.45.8.1.3.1.10 | ColumnwlanWDSDefaultKey | read-create | current | Number of the WEP key to use for encryption of outgoing WDS frames. |
| 1.3.6.1.4.1.45.8.1.3.1.11 | ColumnwlanWDSKey1 | read-create | current | Key string for WEP key nr. 1. Allowed number of octets are 5 for WEP-40 and 13 for WEP-104. |
| 1.3.6.1.4.1.45.8.1.3.1.12 | ColumnwlanWDSKey2 | read-create | current | Key string for WEP key nr. 2. Allowed number of octets are 5 for WEP-40 and 13 for WEP-104. |
| 1.3.6.1.4.1.45.8.1.3.1.13 | ColumnwlanWDSKey3 | read-create | current | Key string for WEP key nr. 3. Allowed number of octets are 5 for WEP-40 and 13 for WEP-104. |
| 1.3.6.1.4.1.45.8.1.3.1.14 | ColumnwlanWDSKey4 | read-create | current | Key string for WEP key nr. 4. Allowed number of octets are 5 for WEP-40 and 13 for WEP-104. |
| 1.3.6.1.4.1.45.8.1.3.1.15 | ColumnwlanWDSPassPhrase | read-create | current | Passphrase string for WDS encryption type TKIP and AES. |
| 1.3.6.1.4.1.45.8.1.3.1.17 | ColumnwlanWDSMSDUTx | read-only | current | This attribute counts the total number of packets transmitted on this WDS link. |
| 1.3.6.1.4.1.45.8.1.3.1.18 | ColumnwlanWDSMSDURx | read-only | current | This attribute counts the total number of packets received on this WDS link. |
| 1.3.6.1.4.1.45.8.1.3.1.19 | ColumnwlanWDSBytesTx | read-only | current | This attribute counts the total number of octets transmitted on this WDS link. |
| 1.3.6.1.4.1.45.8.1.3.1.20 | ColumnwlanWDSBytesRx | read-only | current | This attribute counts the total number of octets received on this WDS link. |
| 1.3.6.1.4.1.45.8.1.3.1.21 | ColumnwlanWDSCurrentRate | read-only | current | This attribute returns the current receive data rate for this link in 500 Kbps units, or 0 if no connection can be established. |
| 1.3.6.1.4.1.45.8.1.3.1.22 | ColumnwlanWDSCurrentRSSI | read-only | current | This attribute returns the current receive signal strength for this link, or 0 if no connection can be established. |
| 1.3.6.1.4.1.45.8.1.3.1.23 | ColumnwlanWDSCurrentNoise | read-only | current | This attribute shows the measured noise level in dBm, or 0 if no connection can be established. |
| 1.3.6.1.4.1.45.8.1.3.1.24 | ColumnwlanWDSTransientKey | not-accessible | current | Transient key generated from Passphrase string for WDS encryption type TKIP and AES. |
| 1.3.6.1.4.1.45.8.1.3.1.25 | ColumnwlanWDSLocalAddress | read-create | current | Local MAC Address for the WDS link. |
| 1.3.6.1.4.1.45.8.1.3.1.26 | ColumnwlanWDSTimeoutCount | not-accessible | current | This counter increments every second if no packets are received from link partner. If a certain threshold is reached, an ArbopAnnounceLinkUp packet is transmit… |
| 1.3.6.1.4.1.45.8.1.3.1.27 | ColumnwlanWDSRxFrames54 | read-only | current | This attribute shows the number of data frames that were received at 54 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.28 | ColumnwlanWDSRxFrames48 | read-only | current | This attribute shows the number of data frames that were received at 48 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.29 | ColumnwlanWDSRxFrames36 | read-only | current | This attribute shows the number of data frames that were received at 36 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.30 | ColumnwlanWDSRxFrames24 | read-only | current | This attribute shows the number of data frames that were received at 24 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.31 | ColumnwlanWDSRxFrames18 | read-only | current | This attribute shows the number of data frames that were received at 18 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.32 | ColumnwlanWDSRxFrames12 | read-only | current | This attribute shows the number of data frames that were received at 12 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.33 | ColumnwlanWDSRxFrames11 | read-only | current | This attribute shows the number of data frames that were received at 11 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.34 | ColumnwlanWDSRxFrames9 | read-only | current | This attribute shows the number of data frames that were received at 9 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.35 | ColumnwlanWDSRxFrames6 | read-only | current | This attribute shows the number of data frames that were received at 6 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.36 | ColumnwlanWDSRxFrames5 | read-only | current | This attribute shows the number of data frames that were received at 5.5 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.37 | ColumnwlanWDSRxFrames2 | read-only | current | This attribute shows the number of data frames that were received at 2 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.38 | ColumnwlanWDSRxFrames1 | read-only | current | This attribute shows the number of data frames that were received at 1 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.39 | ColumnwlanWDSTxFrames54 | read-only | current | This attribute shows the number of data frames that were transmitted at 54 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.40 | ColumnwlanWDSTxFrames48 | read-only | current | This attribute shows the number of data frames that were transmitted at 48 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.41 | ColumnwlanWDSTxFrames36 | read-only | current | This attribute shows the number of data frames that were transmitted at 36 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.42 | ColumnwlanWDSTxFrames24 | read-only | current | This attribute shows the number of data frames that were transmitted at 24 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.43 | ColumnwlanWDSTxFrames18 | read-only | current | This attribute shows the number of data frames that were transmitted at 18 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.44 | ColumnwlanWDSTxFrames12 | read-only | current | This attribute shows the number of data frames that were transmitted at 12 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.45 | ColumnwlanWDSTxFrames11 | read-only | current | This attribute shows the number of data frames that were transmitted at 11 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.46 | ColumnwlanWDSTxFrames9 | read-only | current | This attribute shows the number of data frames that were transmitted at 9 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.47 | ColumnwlanWDSTxFrames6 | read-only | current | This attribute shows the number of data frames that were transmitted at 6 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.48 | ColumnwlanWDSTxFrames5 | read-only | current | This attribute shows the number of data frames that were transmitted at 5.5 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.49 | ColumnwlanWDSTxFrames2 | read-only | current | This attribute shows the number of data frames that were transmitted at 2 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.50 | ColumnwlanWDSTxFrames1 | read-only | current | This attribute shows the number of data frames that were transmitted at 1 Mbps. |
| 1.3.6.1.4.1.45.8.1.3.1.51 | ColumnwlanWDSCurrentRSSI1 | read-only | current | This attribute returns the current receive signal strength on the first receiver for this link, or 0 if no connection can be established. |
| 1.3.6.1.4.1.45.8.1.3.1.52 | ColumnwlanWDSCurrentRSSI2 | read-only | current | This attribute returns the current receive signal strength on the second receiver for this link, or 0 if no second receiver present or no connection can be est… |
| 1.3.6.1.4.1.45.8.1.3.1.53 | ColumnwlanWDSCurrentRSSI3 | read-only | current | This attribute returns the current receive signal strength on the third receiver for this link, or 0 if no third receiver present or no connection can be estab… |
| 1.3.6.1.4.1.45.8.1.5 | TablewlanStationTable | not-accessible | current | The wlanStationTable contains information relating to the clients currently associated to our access points. Each entry corresponds to an associated client sta… |
| 1.3.6.1.4.1.45.8.1.5.1 | RowwlanStationEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.5.1.1 | ColumnwlanStationIfIndex | read-only | current | The WLAN radio index. |
| 1.3.6.1.4.1.45.8.1.5.1.2 | ColumnwlanStationAddress | read-only | current | MAC Address of the Assigned STA. |
| 1.3.6.1.4.1.45.8.1.5.1.3 | ColumnwlanStationVSSIndex | read-only | current | The ifindex of the associated Service Set. |
| 1.3.6.1.4.1.45.8.1.5.1.4 | ColumnwlanStationState | read-write | current | |
| 1.3.6.1.4.1.45.8.1.5.1.5 | ColumnwlanStationSecurity | read-only | current | The Security Option of the Station. |
| 1.3.6.1.4.1.45.8.1.5.1.6 | ColumnwlanStationNode | read-only | current | |
| 1.3.6.1.4.1.45.8.1.5.1.8 | ColumnwlanStationMSDUTx | read-only | current | This attribute counts the total number of packets transmitted to this station. |
| 1.3.6.1.4.1.45.8.1.5.1.9 | ColumnwlanStationMSDURx | read-only | current | This attribute counts the total number of packets received from this station. |
| 1.3.6.1.4.1.45.8.1.5.1.10 | ColumnwlanStationBytesTx | read-only | current | This attribute counts the total number of octets transmitted to this station. |
| 1.3.6.1.4.1.45.8.1.5.1.11 | ColumnwlanStationBytesRx | read-only | current | This attribute counts the total number of octets received from this station. |
| 1.3.6.1.4.1.45.8.1.5.1.12 | ColumnwlanStationRate | read-only | current | This attribute reflects the data rate of the latest packet received from this station, in 500 kbps units. |
| 1.3.6.1.4.1.45.8.1.5.1.13 | ColumnwlanStationSignal | read-only | current | This attribute shows the received signal strength in dBm. |
| 1.3.6.1.4.1.45.8.1.5.1.14 | ColumnwlanStationNoise | read-only | current | This attribute shows the measured noise level in dBm, or 0 if no connection can be established. |
| 1.3.6.1.4.1.45.8.1.5.1.15 | ColumnwlanStationConnectTime | read-only | current | This attribute records the system uptime at the moment the client successfully finished association. |
| 1.3.6.1.4.1.45.8.1.5.1.16 | ColumnwlanStationTimeoutTStamp | not-accessible | current | Internal time stamp of the most recent STA timeout poll. |
| 1.3.6.1.4.1.45.8.1.5.1.17 | ColumnwlanStationTimeoutCount | not-accessible | current | Internal counter for number of polls sent to the STA without reply. |
| 1.3.6.1.4.1.45.8.1.5.1.30 | ColumnwlanStationRxFrames54 | read-only | current | This attribute shows the number of data frames that were received at 54 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.31 | ColumnwlanStationRxFrames48 | read-only | current | This attribute shows the number of data frames that were received at 48 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.32 | ColumnwlanStationRxFrames36 | read-only | current | This attribute shows the number of data frames that were received at 36 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.33 | ColumnwlanStationRxFrames24 | read-only | current | This attribute shows the number of data frames that were received at 24 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.34 | ColumnwlanStationRxFrames18 | read-only | current | This attribute shows the number of data frames that were received at 18 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.35 | ColumnwlanStationRxFrames12 | read-only | current | This attribute shows the number of data frames that were received at 12 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.36 | ColumnwlanStationRxFrames11 | read-only | current | This attribute shows the number of data frames that were received at 11 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.37 | ColumnwlanStationRxFrames9 | read-only | current | This attribute shows the number of data frames that were received at 9 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.38 | ColumnwlanStationRxFrames6 | read-only | current | This attribute shows the number of data frames that were received at 6 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.39 | ColumnwlanStationRxFrames5 | read-only | current | This attribute shows the number of data frames that were received at 5.5 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.40 | ColumnwlanStationRxFrames2 | read-only | current | This attribute shows the number of data frames that were received at 2 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.41 | ColumnwlanStationRxFrames1 | read-only | current | This attribute shows the number of data frames that were received at 1 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.42 | ColumnwlanStationTxFrames54 | read-only | current | This attribute shows the number of data frames that were transmitted at 54 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.43 | ColumnwlanStationTxFrames48 | read-only | current | This attribute shows the number of data frames that were transmitted at 48 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.44 | ColumnwlanStationTxFrames36 | read-only | current | This attribute shows the number of data frames that were transmitted at 36 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.45 | ColumnwlanStationTxFrames24 | read-only | current | This attribute shows the number of data frames that were transmitted at 24 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.46 | ColumnwlanStationTxFrames18 | read-only | current | This attribute shows the number of data frames that were transmitted at 18 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.47 | ColumnwlanStationTxFrames12 | read-only | current | This attribute shows the number of data frames that were transmitted at 12 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.48 | ColumnwlanStationTxFrames11 | read-only | current | This attribute shows the number of data frames that were transmitted at 11 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.49 | ColumnwlanStationTxFrames9 | read-only | current | This attribute shows the number of data frames that were transmitted at 9 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.50 | ColumnwlanStationTxFrames6 | read-only | current | This attribute shows the number of data frames that were transmitted at 6 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.51 | ColumnwlanStationTxFrames5 | read-only | current | This attribute shows the number of data frames that were transmitted at 5.5 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.52 | ColumnwlanStationTxFrames2 | read-only | current | This attribute shows the number of data frames that were transmitted at 2 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.53 | ColumnwlanStationTxFrames1 | read-only | current | This attribute shows the number of data frames that were transmitted at 1 Mbps. |
| 1.3.6.1.4.1.45.8.1.5.1.54 | ColumnwlanStationIpAddress | read-only | current | This attribute shows the IP address of the client. It is only available if any IP frames have been received from the client. |
| 1.3.6.1.4.1.45.8.1.5.1.55 | ColumnwlanStationRSSI1 | read-only | current | This attribute shows the received signal strength at the first receiver in dBm. The value 0 indicates no connection. |
| 1.3.6.1.4.1.45.8.1.5.1.56 | ColumnwlanStationRSSI2 | read-only | current | This attribute shows the received signal strength at the second receiver in dBm. The value 0 indicates no connection or no second receiver present. |
| 1.3.6.1.4.1.45.8.1.5.1.57 | ColumnwlanStationRSSI3 | read-only | current | This attribute shows the received signal strength at the third receiver in dBm. The value 0 indicates no connection or no third receiver present. |
| 1.3.6.1.4.1.45.8.1.5.1.82 | ColumnwlanStationRxAirtime | read-only | current | Accumulated estimated time in microseconds for all unidirectional frames received from this station. |
| 1.3.6.1.4.1.45.8.1.5.1.83 | ColumnwlanStationTxAirtime | read-only | current | Accumulated estimated time in microseconds for all unidirectional frames transmitted to this station. |
| 1.3.6.1.4.1.45.8.1.5.1.84 | ColumnwlanStationCapabilities | read-only | current | This field contains supported capabilities of a station. uapsd-vo := AC_VO U-APSD Flag enabled uapsd-vi := AC_VI U-APSD Flag enabled uapsd-bk := AC_BK U-APSD F… |
| 1.3.6.1.4.1.45.8.1.5.1.85 | ColumnwlanStationLastSeen | read-only | current | Timestamp of the last received frame by this Station |
| 1.3.6.1.4.1.45.8.1.5.1.86 | ColumnwlanStationRxDiscards | read-only | current | Count of discarded bytes due to bandwidth limitation. see wlanVSSStationRxShaping |
| 1.3.6.1.4.1.45.8.1.5.1.87 | ColumnwlanStationTxDiscards | read-only | current | Count of discarded bytes due to bandwidth limitation. see wlanVSSStationTxShaping |
| 1.3.6.1.4.1.45.8.1.6 | TablewlanMACTable | not-accessible | current | The wlanStationTable contains information relating to the interfaces available on the system. Each entry corresponds to an available wlan interface. Entries ca… |
| 1.3.6.1.4.1.45.8.1.6.1 | RowwlanMACEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.6.1.1 | ColumnwlanMACAddress | read-write | current | The Objects MAC Address |
| 1.3.6.1.4.1.45.8.1.6.1.2 | ColumnwlanMACIfIndex | read-write | current | The Objects associated WLAN Hardware |
| 1.3.6.1.4.1.45.8.1.6.1.3 | ColumnwlanMACRule | read-write | current | The Rule of the MAC Object |
| 1.3.6.1.4.1.45.8.1.6.1.4 | ColumnwlanMACMask | read-write | current | Service Sets associated with this Object max. 256 Bit |
| 1.3.6.1.4.1.45.8.1.7 | TablewlanACLDeniedTable | not-accessible | current | Contains all MAC Addresses of denied clients |
| 1.3.6.1.4.1.45.8.1.7.1 | RowwlanACLDeniedEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.7.1.1 | ColumnwlanACLDeniedAddress | read-only | current | The MAC Address of the denied Client |
| 1.3.6.1.4.1.45.8.1.7.1.2 | ColumnwlanACLDeniedIfIndex | read-only | current | The Interface the Deniued Address belongs to |
| 1.3.6.1.4.1.45.8.1.7.1.3 | ColumnwlanACLDeniedCount | read-only | current | The count of detected denies to this MAC Address |
| 1.3.6.1.4.1.45.8.1.7.1.4 | ColumnwlanACLDeniedAge | read-only | current | The Age of the last MAX-ACCESS |
| 1.3.6.1.4.1.45.8.1.8 | TablewlanACLTable | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.8.1 | RowwlanACLEntry | not-accessible | current | The WLAN Access List based on MAC Addresses |
| 1.3.6.1.4.1.45.8.1.8.1.1 | ColumnwlanACLAddress | read-write | current | The MAC Address for the accepted client |
| 1.3.6.1.4.1.45.8.1.8.1.2 | ColumnwlanACLIfIndex | read-write | current | The VSS Interface the MAC Address belongs |
| 1.3.6.1.4.1.45.8.1.8.1.3 | ColumnwlanACLStatus | read-write | current | The Status for the entry (delete) |
| 1.3.6.1.4.1.45.8.1.9 | TablewlanWDSAutoConfigTable | not-accessible | current | Attributes for artem bridge link auto-configuration. |
| 1.3.6.1.4.1.45.8.1.9.1 | RowwlanWDSAutoConfigEntry | not-accessible | current | An entry in wlanWDSAutoConfigTable. |
| 1.3.6.1.4.1.45.8.1.9.1.1 | ColumnwlanWDSLinkLockState | read-write | current | This attribute defines if the bridge is locked. Lock state is common for all bridge links using the same radio. If the bridge is locked, it cannot be discovere… |
| 1.3.6.1.4.1.45.8.1.9.1.2 | ColumnwlanWDSLinkConfigScanState | read-write | current | This attribute defines the current auto-configuration state. idle(1) - In this state, writing scanning(2) starts an auto-configuration scan for bridge link pee… |
| 1.3.6.1.4.1.45.8.1.9.1.99 | ColumnwlanWDSAutoConfigIfIndex | read-only | current | Auxiliary index in wlanWDSAutoConfigTable. |
| 1.3.6.1.4.1.45.8.1.10 | TablewlanWDSPeersTable | not-accessible | current | This table contains the results of bridge link auto-configuration scans. Each line represents a possible link partner. |
| 1.3.6.1.4.1.45.8.1.10.1 | RowwlanWDSPeersEntry | not-accessible | current | An entry in wlanWDSPeersTable. |
| 1.3.6.1.4.1.45.8.1.10.1.1 | ColumnwlanWDSPeerIndex | read-only | current | The auxiliary variable used to identify instances of the columnar objects in the wlanWDSPeersTable. |
| 1.3.6.1.4.1.45.8.1.10.1.2 | ColumnwlanWDSPeerLinkAliasName | read-only | current | This attribute shows the user-defined alias name for the peer's bridge link. |
| 1.3.6.1.4.1.45.8.1.10.1.3 | ColumnwlanWDSPeerCompointName | read-only | current | This attribute displays the given node name of the peer ComPoint. |
| 1.3.6.1.4.1.45.8.1.10.1.4 | ColumnwlanWDSPeerRSSI | read-only | current | This attribute shows the receive signal strength for the signal received from the peer in dBm. |
| 1.3.6.1.4.1.45.8.1.10.1.5 | ColumnwlanWDSPeerLinkAdminStatus | read-only | current | This attribute shows is the peer's bridge link is currently enabled. |
| 1.3.6.1.4.1.45.8.1.10.1.6 | ColumnwlanWDSPeerLockState | read-only | current | This attribute defines if the peer's bridge is locked. Lock state is common for all bridge links using the same radio. If the bridge is locked, it cannot be di… |
| 1.3.6.1.4.1.45.8.1.10.1.7 | ColumnwlanWDSPeerCompointMacAddress | read-only | current | This attribute displays the MAC address of the peer ComPoint. This is not the WLAN radio's MAC address, but rather the MAC address of the first ethernet port. |
| 1.3.6.1.4.1.45.8.1.10.1.8 | ColumnwlanWDSPeerRadioMacAddress | read-only | current | This attribute displays the peer's WLAN radio's MAC address. |
| 1.3.6.1.4.1.45.8.1.10.1.9 | ColumnwlanWDSPeerConfigSetupState | read-write | current | This attribute defines the current auto-configuration setup state of the bridge link. idle(1) - No auto-configuration is currently in progress. In this state, … |
| 1.3.6.1.4.1.45.8.1.10.1.10 | ColumnwlanWDSPeerConfigSetupResult | read-only | current | This attribute holds the result after a bridge link auto-config setup. It is reset whenever a new auto-config setup is triggered. |
| 1.3.6.1.4.1.45.8.1.10.1.11 | ColumnwlanWDSPeerRemoteIfIndex | read-only | current | This is a unique identifier (port ID or ifIndex) for the bridge link on the remote side. |
| 1.3.6.1.4.1.45.8.1.10.1.12 | ColumnwlanWDSPeerRSSI1 | read-only | current | This attribute shows the receive signal strength on the first receiver for the signal received from the peer in dBm. A value of 0 indicates no connection |
| 1.3.6.1.4.1.45.8.1.10.1.13 | ColumnwlanWDSPeerRSSI2 | read-only | current | This attribute shows the receive signal strength on the second receiver for the signal received from the peer in dBm. A value of 0 indicates no connection or n… |
| 1.3.6.1.4.1.45.8.1.10.1.14 | ColumnwlanWDSPeerRSSI3 | read-only | current | This attribute shows the receive signal strength on the third receiver for the signal received from the peer in dBm. A value of 0 indicates no connection or no… |
| 1.3.6.1.4.1.45.8.1.10.1.99 | ColumnwlanWDSPeerIfIndex | read-only | current | Auxiliary index in wlanWDSPeersTable. |
| 1.3.6.1.4.1.45.8.1.11 | TablewlanLinkTestTable | not-accessible | current | This table contains the link test results for every bridge link. Writing any value to the wlanLinkTestUpdate attribute triggers transmission of a new link requ… |
| 1.3.6.1.4.1.45.8.1.11.1 | RowwlanLinkTestEntry | not-accessible | current | An entry in WlanLinkTestEntry. |
| 1.3.6.1.4.1.45.8.1.11.1.1 | ColumnwlanLinkTestSignalLocal | read-only | current | This attribute shows the received signal strength in dBm. |
| 1.3.6.1.4.1.45.8.1.11.1.2 | ColumnwlanLinkTestSignalRemote | read-only | current | This attribute shows the received signal in dBm, as measured by remote bridge link partner. Reading this attribute triggers transmission of a new link request … |
| 1.3.6.1.4.1.45.8.1.11.1.3 | ColumnwlanLinkTestNoiseLocal | read-only | current | This attribute shows the measured noise level in dBm. |
| 1.3.6.1.4.1.45.8.1.11.1.4 | ColumnwlanLinkTestNoiseRemote | read-only | current | This attribute shows the noise level in dBm, as measured by remote bridge link partner. |
| 1.3.6.1.4.1.45.8.1.11.1.5 | ColumnwlanLinkTestSNRLocal | read-only | current | This attribute shows the calculated Signal to Noise ratio in dB. |
| 1.3.6.1.4.1.45.8.1.11.1.6 | ColumnwlanLinkTestSNRRemote | read-only | current | This attribute shows the calculated Signal to Noise ratio in dB, as measured by remote bridge link partner. |
| 1.3.6.1.4.1.45.8.1.11.1.7 | ColumnwlanLinkTestFramesTransmitted | read-only | current | This attribute shows the number of link test frames transmitted. |
| 1.3.6.1.4.1.45.8.1.11.1.8 | ColumnwlanLinkTestFramesReceived | read-only | current | This attribute shows the number of link test frames successfully received. |
| 1.3.6.1.4.1.45.8.1.11.1.9 | ColumnwlanLinkTestFramesLost | read-only | current | This attribute shows the number of link test frames for which no reply has been received and therefore are considered lost. |
| 1.3.6.1.4.1.45.8.1.11.1.10 | ColumnwlanLinkTestRateLocal | read-only | current | This attribute shows the data rate of the most recent received link test frame, in 500 Kbps units. |
| 1.3.6.1.4.1.45.8.1.11.1.11 | ColumnwlanLinkTestRateRemote | read-only | current | This attribute shows the data rate of the most recent link test frame received by the link partner, in 500 Kbps units. |
| 1.3.6.1.4.1.45.8.1.11.1.32 | ColumnwlanLinkTestRxFrames54 | read-only | current | This attribute shows the number of link test frames that were received at 54 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.33 | ColumnwlanLinkTestRxFrames48 | read-only | current | This attribute shows the number of link test frames that were received at 48 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.34 | ColumnwlanLinkTestRxFrames36 | read-only | current | This attribute shows the number of link test frames that were received at 36 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.35 | ColumnwlanLinkTestRxFrames24 | read-only | current | This attribute shows the number of link test frames that were received at 24 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.36 | ColumnwlanLinkTestRxFrames18 | read-only | current | This attribute shows the number of link test frames that were received at 18 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.37 | ColumnwlanLinkTestRxFrames12 | read-only | current | This attribute shows the number of link test frames that were received at 12 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.38 | ColumnwlanLinkTestRxFrames11 | read-only | current | This attribute shows the number of link test frames that were received at 11 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.39 | ColumnwlanLinkTestRxFrames9 | read-only | current | This attribute shows the number of link test frames that were received at 9 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.40 | ColumnwlanLinkTestRxFrames6 | read-only | current | This attribute shows the number of link test frames that were received at 6 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.41 | ColumnwlanLinkTestRxFrames5 | read-only | current | This attribute shows the number of link test frames that were received at 5.5 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.42 | ColumnwlanLinkTestRxFrames2 | read-only | current | This attribute shows the number of link test frames that were received at 2 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.43 | ColumnwlanLinkTestRxFrames1 | read-only | current | This attribute shows the number of link test frames that were received at 1 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.50 | ColumnwlanLinkTestUpdate | read-write | current | Writing any non-zero value to this attribute triggers transmission of a new link request frame. Reading this attribute always returns 0. |
| 1.3.6.1.4.1.45.8.1.11.1.60 | ColumnwlanLinkTestRxFramesRemote54 | read-only | current | This attribute shows the number of link test frames that were received by the remote partner at 54 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.61 | ColumnwlanLinkTestRxFramesRemote48 | read-only | current | This attribute shows the number of link test frames that were received by the remote partner at 48 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.62 | ColumnwlanLinkTestRxFramesRemote36 | read-only | current | This attribute shows the number of link test frames that were received by the remote partner at 36 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.63 | ColumnwlanLinkTestRxFramesRemote24 | read-only | current | This attribute shows the number of link test frames that were received by the remote partner at 24 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.64 | ColumnwlanLinkTestRxFramesRemote18 | read-only | current | This attribute shows the number of link test frames that were received by the remote partner at 18 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.65 | ColumnwlanLinkTestRxFramesRemote12 | read-only | current | This attribute shows the number of link test frames that were received by the remote partner at 12 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.66 | ColumnwlanLinkTestRxFramesRemote11 | read-only | current | This attribute shows the number of link test frames that were received by the remote partner at 11 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.67 | ColumnwlanLinkTestRxFramesRemote9 | read-only | current | This attribute shows the number of link test frames that were received by the remote partner at 9 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.68 | ColumnwlanLinkTestRxFramesRemote6 | read-only | current | This attribute shows the number of link test frames that were received by the remote partner at 6 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.69 | ColumnwlanLinkTestRxFramesRemote5 | read-only | current | This attribute shows the number of link test frames that were received by the remote partner at 5.5 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.70 | ColumnwlanLinkTestRxFramesRemote2 | read-only | current | This attribute shows the number of link test frames that were received by the remote partner at 2 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.71 | ColumnwlanLinkTestRxFramesRemote1 | read-only | current | This attribute shows the number of link test frames that were received by the remote partner at 1 Mbps. |
| 1.3.6.1.4.1.45.8.1.11.1.99 | ColumnwlanLinkTestIfIndex | read-only | current | Auxiliary index in wlanLinkTestTable. |
| 1.3.6.1.4.1.45.8.1.12 | NodewlanBridge | |||
| 1.3.6.1.4.1.45.8.1.12.1 | ScalarwlanBridgeConfigScanTimeout | read-write | current | This attribute defines the maximum time a bridge auto-configuration scan may take. After this timeout has expired, any auto-configuration scan will be aborted,… |
| 1.3.6.1.4.1.45.8.1.12.2 | ScalarwlanBridgeConfigSetupTimeout | read-write | current | This attribute defines the maximum time a bridge auto-configuration setup may take. After this timeout has expired, any auto-configuration setup will be aborte… |
| 1.3.6.1.4.1.45.8.1.13 | TablewlanClientTable | not-accessible | current | Describe a WLAN Client and the correspondending settings |
| 1.3.6.1.4.1.45.8.1.13.1 | RowwlanClientEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.13.1.1 | ColumnwlanClientIndex | read-only | current | Unique Client index. |
| 1.3.6.1.4.1.45.8.1.13.1.2 | ColumnwlanClientIfIndex | read-only | current | IfIndex of the client interface. |
| 1.3.6.1.4.1.45.8.1.13.1.3 | ColumnwlanClientwlanIf | read-write | current | IfIndex of the wlan Interface the client belongs to. |
| 1.3.6.1.4.1.45.8.1.13.1.4 | ColumnwlanClientMode | read-write | current | Switch between infrastructure and ad-hoc mode. |
| 1.3.6.1.4.1.45.8.1.13.1.5 | ColumnwlanClientSSID | read-write | current | The Service Set Name |
| 1.3.6.1.4.1.45.8.1.13.1.6 | ColumnwlanClient11dConformance | read-write | current | none - use own country info flexible - try to get country info from an AP else use own country info strict - try to get country info from an AP else do nothing |
| 1.3.6.1.4.1.45.8.1.13.1.7 | ColumnwlanClientSecurity | read-write | current | The Security Option which will be used. WPA-NONE is a special mode only for Ad-hoc mode. There is no key management that means the key is static (calculated fr… |
| 1.3.6.1.4.1.45.8.1.13.1.8 | ColumnwlanClientDefaultKey | read-write | current | |
| 1.3.6.1.4.1.45.8.1.13.1.9 | ColumnwlanClientKey1 | read-write | current | Key string for WEP key nr. 1. |
| 1.3.6.1.4.1.45.8.1.13.1.10 | ColumnwlanClientKey2 | read-write | current | Key string for WEP key nr. 2. |
| 1.3.6.1.4.1.45.8.1.13.1.11 | ColumnwlanClientKey3 | read-write | current | Key string for WEP key nr. 3. |
| 1.3.6.1.4.1.45.8.1.13.1.12 | ColumnwlanClientKey4 | read-write | current | Key string for WEP key nr. 4. |
| 1.3.6.1.4.1.45.8.1.13.1.13 | ColumnwlanClientPassPhrase | read-write | current | Passphrase string for WPA-PSK and WPA2-PSK. |
| 1.3.6.1.4.1.45.8.1.13.1.14 | ColumnwlanClientRsnPreauthentication | read-write | current | When this object is set to TRUE, this shall indicate that RSNA preauthentication is enabled on this entity. This object requires that dot11RSNAEnabled also be … |
| 1.3.6.1.4.1.45.8.1.13.1.15 | ColumnwlanClientBand | read-write | obsolete | Frequency band |
| 1.3.6.1.4.1.45.8.1.13.1.16 | ColumnwlanClientRoamingPreference | read-write | current | Which band is prefered for association. none : no preference (default) b24-GHz: prefer APs on 2,4 GHz b5-GHz : prefer APs on 5 GHz |
| 1.3.6.1.4.1.45.8.1.13.1.17 | ColumnwlanClientScanThreshold | read-write | current | Threshold in dBm above which the background scan is active. Default is -70dBm. |
| 1.3.6.1.4.1.45.8.1.13.1.18 | ColumnwlanClientScanInterval | read-write | current | Scan interval, in ms, between successive sweeps. Default is 5000ms. |
| 1.3.6.1.4.1.45.8.1.13.1.19 | ColumnwlanClientChannelSweep | read-write | current | Number of frequencies to scan for each background scan. Sweep = 0 disables background scanning. Sweep = -1 causes the sweep to cover all frequencies available.… |
| 1.3.6.1.4.1.45.8.1.13.1.20 | ColumnwlanClientScanPeriodAMin | read-write | current | Minimum time in ms to spend on a frequency when active scanning. Default is 10ms. |
| 1.3.6.1.4.1.45.8.1.13.1.21 | ColumnwlanClientScanPeriodAMax | read-write | current | Maximum time in ms to spend on a frequency when active scanning. Default is 40ms. |
| 1.3.6.1.4.1.45.8.1.13.1.22 | ColumnwlanClientScanPeriodMin | read-write | current | Minimum time in ms to spend on a frequency when passive scanning. Default is 20ms. |
| 1.3.6.1.4.1.45.8.1.13.1.23 | ColumnwlanClientScanPeriodMax | read-write | current | Maximum time in ms to spend on a frequency when passive scanning. Default is 120ms. |
| 1.3.6.1.4.1.45.8.1.13.1.24 | ColumnwlanClientWeightOfAssocAdv | read-write | current | Advantage of the BSS currently associated with. Default is a weight of 10. |
| 1.3.6.1.4.1.45.8.1.13.1.25 | ColumnwlanClientWeightOfRSSIAdv | read-write | current | Weight of the BSS's received signal strength indicator (RSSI). Default is a weight of 10. |
| 1.3.6.1.4.1.45.8.1.13.1.26 | ColumnwlanClientWeightOfAge | read-write | current | Weight of the BSS's age. Default is a weight of 5 |
| 1.3.6.1.4.1.45.8.1.13.1.27 | ColumnwlanClientWeightOfPenalty | read-write | current | Weight of the BSS's penalty. Default is a weigth of 10. |
| 1.3.6.1.4.1.45.8.1.13.1.28 | ColumnwlanClientJoinFailedPenalty | read-write | current | Penalty when joining an AP failed. Default is a penalty value of 50. |
| 1.3.6.1.4.1.45.8.1.13.1.29 | ColumnwlanClientRoamingProfile | read-write | current | All roaming parameters are summarized to profiles for the most used roaming behaviors. fast : client roams if signal is not strong enough for higher data rates… |
| 1.3.6.1.4.1.45.8.1.13.1.30 | ColumnwlanClientSkipChannels | read-write | obsolete | If a bit is set the accordingly channel will be skipped from the channel scan list (channel 1-14 for 2.4 GHz). Default is scan all channels. |
| 1.3.6.1.4.1.45.8.1.13.1.33 | ColumnwlanClientWPAMulticastCipher | read-only | current | The multicast ciphers used for WPA. For WPA and RSN, only one of the following values is allowed: WPA_CIPHERSUITE_NONE(0) WPA_CIPHERSUITE_WEP_40(1) WPA_CIPHERS… |
| 1.3.6.1.4.1.45.8.1.13.1.34 | ColumnwlanClientRSNMulticastCipher | read-only | current | The multicast ciphers used for RSN. For WPA and RSN, only one of the following values is allowed: WPA_CIPHERSUITE_NONE(0) WPA_CIPHERSUITE_WEP_40(1) WPA_CIPHERS… |
| 1.3.6.1.4.1.45.8.1.13.1.35 | ColumnwlanClientWPAUnicastCipher | read-write | current | The set of unicast ciphers used for WPA. For WPA and RSN, set one or more of the following bit values: WPA_CIPHERSUITE_NONE(0) WPA_CIPHERSUITE_WEP_40(1) WPA_CI… |
| 1.3.6.1.4.1.45.8.1.13.1.36 | ColumnwlanClientRSNUnicastCipher | read-write | current | The set of unicast ciphers used for RSN. For WPA and RSN, set one or more of the following bit values: WPA_CIPHERSUITE_NONE(0) WPA_CIPHERSUITE_WEP_40(1) WPA_CI… |
| 1.3.6.1.4.1.45.8.1.13.1.37 | ColumnwlanClientRSNCapabilities | read-only | current | The RSN capabilities bytes, |
| 1.3.6.1.4.1.45.8.1.13.1.38 | ColumnwlanClientScanState | read-write | current | This attribute holds the foreground scanning status. Writing scanning(2) in idle state triggers a new foreground scan cycle. All entries for this client interf… |
| 1.3.6.1.4.1.45.8.1.13.1.64 | ColumnwlanClientBss | read-only | current | BSS Id the client is associated with. If client is not associated, this attribute reads 00:00:00:00:00:00. |
| 1.3.6.1.4.1.45.8.1.13.1.65 | ColumnwlanClientCurrSSID | read-only | current | The Service Set Name the client really is associated with. This usually equal to wlanClientSSID, except for empty wlanClientSSID, which means any SSID. |
| 1.3.6.1.4.1.45.8.1.13.1.66 | ColumnwlanClientMSDUTx | read-only | current | Count of transmitted MSDU |
| 1.3.6.1.4.1.45.8.1.13.1.67 | ColumnwlanClientMSDURx | read-only | current | Count of received MSDU |
| 1.3.6.1.4.1.45.8.1.13.1.68 | ColumnwlanClientBytesTx | read-only | current | total number of transmitted bytes |
| 1.3.6.1.4.1.45.8.1.13.1.69 | ColumnwlanClientBytesRx | read-only | current | total number of received bytes |
| 1.3.6.1.4.1.45.8.1.13.1.70 | ColumnwlanClientRate | read-only | current | Data rate of latest received data frame, in 500 kbps units. If client is not associated, this attribute always reads 0. |
| 1.3.6.1.4.1.45.8.1.13.1.71 | ColumnwlanClientRSSI | read-only | current | Receive signal strength of latest received data frame. |
| 1.3.6.1.4.1.45.8.1.13.1.72 | ColumnwlanClientNoise | read-only | current | This attribute shows the measured noise level in dBm, or 0 if no connection can be established. |
| 1.3.6.1.4.1.45.8.1.13.1.73 | ColumnwlanClientRxFrames54 | read-only | current | This attribute shows the number of data frames that were received at 54 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.74 | ColumnwlanClientRxFrames48 | read-only | current | This attribute shows the number of data frames that were received at 48 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.75 | ColumnwlanClientRxFrames36 | read-only | current | This attribute shows the number of data frames that were received at 36 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.76 | ColumnwlanClientRxFrames24 | read-only | current | This attribute shows the number of data frames that were received at 24 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.77 | ColumnwlanClientRxFrames18 | read-only | current | This attribute shows the number of data frames that were received at 18 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.78 | ColumnwlanClientRxFrames12 | read-only | current | This attribute shows the number of data frames that were received at 12 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.79 | ColumnwlanClientRxFrames11 | read-only | current | This attribute shows the number of data frames that were received at 11 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.80 | ColumnwlanClientRxFrames9 | read-only | current | This attribute shows the number of data frames that were received at 9 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.81 | ColumnwlanClientRxFrames6 | read-only | current | This attribute shows the number of data frames that were received at 6 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.82 | ColumnwlanClientRxFrames5 | read-only | current | This attribute shows the number of data frames that were received at 5.5 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.83 | ColumnwlanClientRxFrames2 | read-only | current | This attribute shows the number of data frames that were received at 2 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.84 | ColumnwlanClientRxFrames1 | read-only | current | This attribute shows the number of data frames that were received at 1 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.85 | ColumnwlanClientTxFrames54 | read-only | current | This attribute shows the number of data frames that were transmitted at 54 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.86 | ColumnwlanClientTxFrames48 | read-only | current | This attribute shows the number of data frames that were transmitted at 48 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.87 | ColumnwlanClientTxFrames36 | read-only | current | This attribute shows the number of data frames that were transmitted at 36 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.88 | ColumnwlanClientTxFrames24 | read-only | current | This attribute shows the number of data frames that were transmitted at 24 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.89 | ColumnwlanClientTxFrames18 | read-only | current | This attribute shows the number of data frames that were transmitted at 18 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.90 | ColumnwlanClientTxFrames12 | read-only | current | This attribute shows the number of data frames that were transmitted at 12 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.91 | ColumnwlanClientTxFrames11 | read-only | current | This attribute shows the number of data frames that were transmitted at 11 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.92 | ColumnwlanClientTxFrames9 | read-only | current | This attribute shows the number of data frames that were transmitted at 9 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.93 | ColumnwlanClientTxFrames6 | read-only | current | This attribute shows the number of data frames that were transmitted at 6 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.94 | ColumnwlanClientTxFrames5 | read-only | current | This attribute shows the number of data frames that were transmitted at 5.5 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.95 | ColumnwlanClientTxFrames2 | read-only | current | This attribute shows the number of data frames that were transmitted at 2 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.96 | ColumnwlanClientTxFrames1 | read-only | current | This attribute shows the number of data frames that were transmitted at 1 Mbps. |
| 1.3.6.1.4.1.45.8.1.13.1.97 | ColumnwlanClientRSSI1 | read-only | current | Receive signal strength of latest data frame received by first receiver. A value of 0 inidcates no connection. |
| 1.3.6.1.4.1.45.8.1.13.1.98 | ColumnwlanClientRSSI2 | read-only | current | Receive signal strength of latest data frame received by first receiver. A value of 0 inidcates no second receiver present or no connection. |
| 1.3.6.1.4.1.45.8.1.13.1.99 | ColumnwlanClientRSSI3 | read-only | current | Receive signal strength of latest data frame received by third receiver. A value of 0 inidcates no third receiver present or no connection. |
| 1.3.6.1.4.1.45.8.1.14 | TablewlanStatisticsTable | not-accessible | current | Describe the WLAN statistics of a wlan card |
| 1.3.6.1.4.1.45.8.1.14.1 | RowwlanStatisticsEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.14.1.1 | ColumnwlanStatisticsWlanIf | read-only | current | IfIndex of the wlan Interface the statistics belongs to. |
| 1.3.6.1.4.1.45.8.1.14.1.2 | ColumnwlanStatisticsOperation | read-write | current | Setting this variable to 'refresh' initiates a refresh of the statistic data. After refreshing it is autonomously changed to 'none'. |
| 1.3.6.1.4.1.45.8.1.14.1.10 | ColumnwlanStatisticsMSDUTxSuccess | read-only | current | The number of successfully transmitted unicast MSDUs. |
| 1.3.6.1.4.1.45.8.1.14.1.11 | ColumnwlanStatisticsMSDUTxMulti | read-only | current | The number of successfully transmitted multicast MSDUs. |
| 1.3.6.1.4.1.45.8.1.14.1.12 | ColumnwlanStatisticsMSDUTxDropped | read-only | current | The number of unicast and multicast MSDUs dropped before a transmission attempt was made. |
| 1.3.6.1.4.1.45.8.1.14.1.13 | ColumnwlanStatisticsMSDUTxFailed | read-only | current | The number of unicast and multicast MSDUs that could not be or were not successfully transmitted by the device. |
| 1.3.6.1.4.1.45.8.1.14.1.14 | ColumnwlanStatisticsMPDUTx | read-only | current | The number of successfully transmitted unicast and multicast MPDUs. |
| 1.3.6.1.4.1.45.8.1.14.1.15 | ColumnwlanStatisticsMPDUTxOneRetry | read-only | current | The number of unicast MPDUs successfully transmitted after one retry. |
| 1.3.6.1.4.1.45.8.1.14.1.16 | ColumnwlanStatisticsMPDUTxMultiRetry | read-only | current | The number of unicast MPDUs successfully transmitted after two or more retries. |
| 1.3.6.1.4.1.45.8.1.14.1.17 | ColumnwlanStatisticsMPDUTxFailed | read-only | current | The number of unicast MPDUs for which the maximum number of retries were exceeded. |
| 1.3.6.1.4.1.45.8.1.14.1.18 | ColumnwlanStatisticsMSDURxSuccess | read-only | current | The number of successfully received unicast MSDUs. |
| 1.3.6.1.4.1.45.8.1.14.1.19 | ColumnwlanStatisticsMSDURxMulti | read-only | current | The number of successfully received multicast MSDUs. |
| 1.3.6.1.4.1.45.8.1.14.1.20 | ColumnwlanStatisticsMSDURxDropped | read-only | current | The number of dropped unicast and multicast MSDUs. |
| 1.3.6.1.4.1.45.8.1.14.1.21 | ColumnwlanStatisticsMSDURxFailed | read-only | current | The number of partially or erroneously received unitcast and multicast MSDUs. |
| 1.3.6.1.4.1.45.8.1.14.1.22 | ColumnwlanStatisticsMPDURx | read-only | current | The number of successfully received unicast MPDUs. |
| 1.3.6.1.4.1.45.8.1.14.1.23 | ColumnwlanStatisticsMPDURxDups | read-only | current | The number of successfully received unicast MPDUs that were a duplicate of earlier frames. |
| 1.3.6.1.4.1.45.8.1.14.1.24 | ColumnwlanStatisticsRTSSuccess | read-only | current | The number of CTS frames received in response to an RTS frame. |
| 1.3.6.1.4.1.45.8.1.14.1.25 | ColumnwlanStatisticsRTSFailed | read-only | current | The number of transmitted RTS frames for which no response CTS frame was received. |
| 1.3.6.1.4.1.45.8.1.14.1.26 | ColumnwlanStatisticsACKFailed | read-only | current | The object counts the number of frame transmissions for which an acknowledgment response frame was expected but not received. |
| 1.3.6.1.4.1.45.8.1.14.1.27 | ColumnwlanStatisticsFramesRx | read-only | current | The number of successfully received frames, before any address and type filtering. |
| 1.3.6.1.4.1.45.8.1.14.1.28 | ColumnwlanStatisticsFrameRxError | read-only | current | The number of unsuccessfully received frames. |
| 1.3.6.1.4.1.45.8.1.14.1.29 | ColumnwlanStatisticsFrameAborts | read-only | current | The number of aborted frames. |
| 1.3.6.1.4.1.45.8.1.14.1.30 | ColumnwlanStatisticsFrameAbortsPHY | read-only | current | The number of PHY aborted frames. |
| 1.3.6.1.4.1.45.8.1.14.1.31 | ColumnwlanStatisticsPrivTxRejected | read-only | current | The number of MPDUs that were not transmitted because no appropriate privacy configuration was available. |
| 1.3.6.1.4.1.45.8.1.14.1.32 | ColumnwlanStatisticsPrivRxPlain | read-only | current | The number of received MPDUs that were rejected because they were unencrypted. |
| 1.3.6.1.4.1.45.8.1.14.1.33 | ColumnwlanStatisticsPrivRxFailed | read-only | current | The number of received crypted MPDUs that were rejected because they could not be successfully decrypted. |
| 1.3.6.1.4.1.45.8.1.14.1.34 | ColumnwlanStatisticsPrivRxNoKey | read-only | current | The number of received crypted MPDUs that could not be decrypted because no key was available for decryption. |
| 1.3.6.1.4.1.45.8.1.15 | TablewlanScanResultsTable | not-accessible | current | This table contains the list of BSS entries found by foreground or background scanning in client mode. |
| 1.3.6.1.4.1.45.8.1.15.1 | RowwlanScanResultsEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.15.1.1 | ColumnwlanScanResultsIfIndex | read-only | current | ifIndex of the WLAN Interface the scan results belong to. |
| 1.3.6.1.4.1.45.8.1.15.1.2 | ColumnwlanScanResultsIndex | read-only | current | Auxiliary index for different BSS entries. |
| 1.3.6.1.4.1.45.8.1.15.1.3 | ColumnwlanScanResultsBSSID | read-only | current | BSSID of this BSS. |
| 1.3.6.1.4.1.45.8.1.15.1.4 | ColumnwlanScanResultsAge | read-only | current | Age of this BSS entry. |
| 1.3.6.1.4.1.45.8.1.15.1.5 | ColumnwlanScanResultsRSSI | read-only | current | Receive signal strength of this BSS. |
| 1.3.6.1.4.1.45.8.1.15.1.6 | ColumnwlanScanResultsSSID | read-only | current | SSID aka network name of this BSS. If broadcasting of SSID is disabled on this BSS, this string may be empty. |
| 1.3.6.1.4.1.45.8.1.15.1.7 | ColumnwlanScanResultsChannel | read-only | current | The channel this BSS was received on. |
| 1.3.6.1.4.1.45.8.1.15.1.8 | ColumnwlanScanResultsDTIMPeriod | read-only | current | The number of DTIM intervals between the start of CFPs for this BSS. |
| 1.3.6.1.4.1.45.8.1.15.1.9 | ColumnwlanScanResultsBeaconPeriod | read-only | current | This attribute contains the number of TU that this BSS uses for scheduling Beacon transmissions. |
| 1.3.6.1.4.1.45.8.1.15.1.10 | ColumnwlanScanResultsCapInfo | read-only | current | The number of DTIM intervals between the start of CFPs for this BSS. |
| 1.3.6.1.4.1.45.8.1.15.1.11 | ColumnwlanScanResultsRates | read-only | current | This attribute contains one octet for each supported rate in this BSS, in 500 Kbps units. |
| 1.3.6.1.4.1.45.8.1.15.1.12 | ColumnwlanScanResultsBasicRates | read-only | current | This attribute contains one octet for each required basic rate in this BSS, in 500 Kbps units. |
| 1.3.6.1.4.1.45.8.1.15.1.13 | ColumnwlanScanResultsExtendedRates | read-only | current | This attribute contains one octet for each supported extended rate in this BSS, in 500 Kbps units. |
| 1.3.6.1.4.1.45.8.1.15.1.14 | ColumnwlanScanResultsFrameData | read-only | current | This attribute contains raw data from 802.11 beacon or probe response frames, starting with the 802.11 timestamp. |
| 1.3.6.1.4.1.45.8.1.15.1.15 | ColumnwlanScanResultsType | read-only | current | This attribute contains the device type of the scanned device. |
| 1.3.6.1.4.1.45.8.1.15.1.16 | ColumnwlanScanResultsPrivacy | read-only | current | This attribute contains the privacy type of the scanned device. |
| 1.3.6.1.4.1.45.8.1.15.1.17 | ColumnwlanScanResultsWPAUnicastCipher | read-only | current | This attribute contains the WPA unicast ciphers of the scanned device. |
| 1.3.6.1.4.1.45.8.1.15.1.18 | ColumnwlanScanResultsRSNUnicastCipher | read-only | current | This attribute contains the RSN unicast ciphers of the scanned device. |
| 1.3.6.1.4.1.45.8.1.15.1.19 | ColumnwlanScanResultsRSSI1 | read-only | current | Receive signal strength of this BSS at first receiver. |
| 1.3.6.1.4.1.45.8.1.15.1.20 | ColumnwlanScanResultsRSSI2 | read-only | current | Receive signal strength of this BSS at second receiver. A value of 0 indicates no second receiver present. |
| 1.3.6.1.4.1.45.8.1.15.1.21 | ColumnwlanScanResultsRSSI3 | read-only | current | Receive signal strength of this BSS at third receiver. A value of 0 indicates no third receiver present. |
| 1.3.6.1.4.1.45.8.1.15.1.24 | ColumnwlanScanResultsSignal | read-only | current | Receive signal strength of this BSS. |
| 1.3.6.1.4.1.45.8.1.16 | TablewlanStationHTStatsTable | not-accessible | current | The wlanStationHTStatsTable contains additional statistical data about 802.11n HT frames related to the clients currently associated to our access points. Each… |
| 1.3.6.1.4.1.45.8.1.16.1 | RowwlanStationHTStatsEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.16.1.1 | ColumnwlanStationHTStatsRxFramesMCS0 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 0. |
| 1.3.6.1.4.1.45.8.1.16.1.2 | ColumnwlanStationHTStatsRxFramesMCS1 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 1. |
| 1.3.6.1.4.1.45.8.1.16.1.3 | ColumnwlanStationHTStatsRxFramesMCS2 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 2. |
| 1.3.6.1.4.1.45.8.1.16.1.4 | ColumnwlanStationHTStatsRxFramesMCS3 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 3. |
| 1.3.6.1.4.1.45.8.1.16.1.5 | ColumnwlanStationHTStatsRxFramesMCS4 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 4. |
| 1.3.6.1.4.1.45.8.1.16.1.6 | ColumnwlanStationHTStatsRxFramesMCS5 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 5. |
| 1.3.6.1.4.1.45.8.1.16.1.7 | ColumnwlanStationHTStatsRxFramesMCS6 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 6. |
| 1.3.6.1.4.1.45.8.1.16.1.8 | ColumnwlanStationHTStatsRxFramesMCS7 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 7. |
| 1.3.6.1.4.1.45.8.1.16.1.9 | ColumnwlanStationHTStatsRxFramesMCS8 | read-only | current | This attribute shows the number of data frames that were received at MCS 8. |
| 1.3.6.1.4.1.45.8.1.16.1.10 | ColumnwlanStationHTStatsRxFramesMCS9 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 9. |
| 1.3.6.1.4.1.45.8.1.16.1.11 | ColumnwlanStationHTStatsRxFramesMCS10 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 10. |
| 1.3.6.1.4.1.45.8.1.16.1.12 | ColumnwlanStationHTStatsRxFramesMCS11 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 11. |
| 1.3.6.1.4.1.45.8.1.16.1.13 | ColumnwlanStationHTStatsRxFramesMCS12 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 12. |
| 1.3.6.1.4.1.45.8.1.16.1.14 | ColumnwlanStationHTStatsRxFramesMCS13 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 13. |
| 1.3.6.1.4.1.45.8.1.16.1.15 | ColumnwlanStationHTStatsRxFramesMCS14 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 14. |
| 1.3.6.1.4.1.45.8.1.16.1.16 | ColumnwlanStationHTStatsRxFramesMCS15 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 15. |
| 1.3.6.1.4.1.45.8.1.16.1.17 | ColumnwlanStationHTStatsTxFramesMCS0 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 0. |
| 1.3.6.1.4.1.45.8.1.16.1.18 | ColumnwlanStationHTStatsTxFramesMCS1 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 1. |
| 1.3.6.1.4.1.45.8.1.16.1.19 | ColumnwlanStationHTStatsTxFramesMCS2 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 2. |
| 1.3.6.1.4.1.45.8.1.16.1.20 | ColumnwlanStationHTStatsTxFramesMCS3 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 3. |
| 1.3.6.1.4.1.45.8.1.16.1.21 | ColumnwlanStationHTStatsTxFramesMCS4 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 4. |
| 1.3.6.1.4.1.45.8.1.16.1.22 | ColumnwlanStationHTStatsTxFramesMCS5 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 5. |
| 1.3.6.1.4.1.45.8.1.16.1.23 | ColumnwlanStationHTStatsTxFramesMCS6 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 6. |
| 1.3.6.1.4.1.45.8.1.16.1.24 | ColumnwlanStationHTStatsTxFramesMCS7 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 7. |
| 1.3.6.1.4.1.45.8.1.16.1.25 | ColumnwlanStationHTStatsTxFramesMCS8 | read-only | current | This attribute shows the number of data frames that were transmitted at MCS 8. |
| 1.3.6.1.4.1.45.8.1.16.1.26 | ColumnwlanStationHTStatsTxFramesMCS9 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 9. |
| 1.3.6.1.4.1.45.8.1.16.1.27 | ColumnwlanStationHTStatsTxFramesMCS10 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 10. |
| 1.3.6.1.4.1.45.8.1.16.1.28 | ColumnwlanStationHTStatsTxFramesMCS11 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 11. |
| 1.3.6.1.4.1.45.8.1.16.1.29 | ColumnwlanStationHTStatsTxFramesMCS12 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 12. |
| 1.3.6.1.4.1.45.8.1.16.1.30 | ColumnwlanStationHTStatsTxFramesMCS13 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 13. |
| 1.3.6.1.4.1.45.8.1.16.1.31 | ColumnwlanStationHTStatsTxFramesMCS14 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 14. |
| 1.3.6.1.4.1.45.8.1.16.1.32 | ColumnwlanStationHTStatsTxFramesMCS15 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 15. |
| 1.3.6.1.4.1.45.8.1.16.1.33 | ColumnwlanStationHTStatsRxBandwidth | read-only | current | This attribute shows the bandwidth the station used with the last received frame: 20 MHz (1) or 40 MHz (2). |
| 1.3.6.1.4.1.45.8.1.16.1.34 | ColumnwlanStationHTStatsRxGuardInterval | read-only | current | This attribute shows the length of the guard interval the station used with the last received frame: long (1) or short (2). |
| 1.3.6.1.4.1.45.8.1.16.1.35 | ColumnwlanStationHTStatsTxBandwidth | read-only | current | This attribute shows the bandwidth the access point used for transmitting the last frame: 20 MHz (1) or 40 MHz (2). |
| 1.3.6.1.4.1.45.8.1.16.1.36 | ColumnwlanStationHTStatsTxGuardInterval | read-only | current | This attribute shows the length of the guard interval the access point used for transmitting the last frame: long (1) or short (2). |
| 1.3.6.1.4.1.45.8.1.16.1.37 | ColumnwlanStationHTStatsRxFramesMCS16 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 16. |
| 1.3.6.1.4.1.45.8.1.16.1.38 | ColumnwlanStationHTStatsRxFramesMCS17 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 17. |
| 1.3.6.1.4.1.45.8.1.16.1.39 | ColumnwlanStationHTStatsRxFramesMCS18 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 18. |
| 1.3.6.1.4.1.45.8.1.16.1.40 | ColumnwlanStationHTStatsRxFramesMCS19 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 19. |
| 1.3.6.1.4.1.45.8.1.16.1.41 | ColumnwlanStationHTStatsRxFramesMCS20 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 20. |
| 1.3.6.1.4.1.45.8.1.16.1.42 | ColumnwlanStationHTStatsRxFramesMCS21 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 21. |
| 1.3.6.1.4.1.45.8.1.16.1.43 | ColumnwlanStationHTStatsRxFramesMCS22 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 22. |
| 1.3.6.1.4.1.45.8.1.16.1.44 | ColumnwlanStationHTStatsRxFramesMCS23 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 23. |
| 1.3.6.1.4.1.45.8.1.16.1.45 | ColumnwlanStationHTStatsTxFramesMCS16 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 16. |
| 1.3.6.1.4.1.45.8.1.16.1.46 | ColumnwlanStationHTStatsTxFramesMCS17 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 17. |
| 1.3.6.1.4.1.45.8.1.16.1.47 | ColumnwlanStationHTStatsTxFramesMCS18 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 18. |
| 1.3.6.1.4.1.45.8.1.16.1.48 | ColumnwlanStationHTStatsTxFramesMCS19 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 19. |
| 1.3.6.1.4.1.45.8.1.16.1.49 | ColumnwlanStationHTStatsTxFramesMCS20 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 20. |
| 1.3.6.1.4.1.45.8.1.16.1.50 | ColumnwlanStationHTStatsTxFramesMCS21 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 21. |
| 1.3.6.1.4.1.45.8.1.16.1.51 | ColumnwlanStationHTStatsTxFramesMCS22 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 22. |
| 1.3.6.1.4.1.45.8.1.16.1.52 | ColumnwlanStationHTStatsTxFramesMCS23 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 23. |
| 1.3.6.1.4.1.45.8.1.17 | TablewlanClientHTStatsTable | not-accessible | current | The wlanClientHTStatsTable contains additional statistical data about 802.11n HT frames related client mode. Each entry corresponds to an wlanClientTable entry… |
| 1.3.6.1.4.1.45.8.1.17.1 | RowwlanClientHTStatsEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.17.1.1 | ColumnwlanClientHTStatsRxFramesMCS0 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 0. |
| 1.3.6.1.4.1.45.8.1.17.1.2 | ColumnwlanClientHTStatsRxFramesMCS1 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 1. |
| 1.3.6.1.4.1.45.8.1.17.1.3 | ColumnwlanClientHTStatsRxFramesMCS2 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 2. |
| 1.3.6.1.4.1.45.8.1.17.1.4 | ColumnwlanClientHTStatsRxFramesMCS3 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 3. |
| 1.3.6.1.4.1.45.8.1.17.1.5 | ColumnwlanClientHTStatsRxFramesMCS4 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 4. |
| 1.3.6.1.4.1.45.8.1.17.1.6 | ColumnwlanClientHTStatsRxFramesMCS5 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 5. |
| 1.3.6.1.4.1.45.8.1.17.1.7 | ColumnwlanClientHTStatsRxFramesMCS6 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 6. |
| 1.3.6.1.4.1.45.8.1.17.1.8 | ColumnwlanClientHTStatsRxFramesMCS7 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 7. |
| 1.3.6.1.4.1.45.8.1.17.1.9 | ColumnwlanClientHTStatsRxFramesMCS8 | read-only | current | This attribute shows the number of data frames that were received at MCS 8. |
| 1.3.6.1.4.1.45.8.1.17.1.10 | ColumnwlanClientHTStatsRxFramesMCS9 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 9. |
| 1.3.6.1.4.1.45.8.1.17.1.11 | ColumnwlanClientHTStatsRxFramesMCS10 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 10. |
| 1.3.6.1.4.1.45.8.1.17.1.12 | ColumnwlanClientHTStatsRxFramesMCS11 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 11. |
| 1.3.6.1.4.1.45.8.1.17.1.13 | ColumnwlanClientHTStatsRxFramesMCS12 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 12. |
| 1.3.6.1.4.1.45.8.1.17.1.14 | ColumnwlanClientHTStatsRxFramesMCS13 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 13. |
| 1.3.6.1.4.1.45.8.1.17.1.15 | ColumnwlanClientHTStatsRxFramesMCS14 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 14. |
| 1.3.6.1.4.1.45.8.1.17.1.16 | ColumnwlanClientHTStatsRxFramesMCS15 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 15. |
| 1.3.6.1.4.1.45.8.1.17.1.17 | ColumnwlanClientHTStatsTxFramesMCS0 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 0. |
| 1.3.6.1.4.1.45.8.1.17.1.18 | ColumnwlanClientHTStatsTxFramesMCS1 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 1. |
| 1.3.6.1.4.1.45.8.1.17.1.19 | ColumnwlanClientHTStatsTxFramesMCS2 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 2. |
| 1.3.6.1.4.1.45.8.1.17.1.20 | ColumnwlanClientHTStatsTxFramesMCS3 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 3. |
| 1.3.6.1.4.1.45.8.1.17.1.21 | ColumnwlanClientHTStatsTxFramesMCS4 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 4. |
| 1.3.6.1.4.1.45.8.1.17.1.22 | ColumnwlanClientHTStatsTxFramesMCS5 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 5. |
| 1.3.6.1.4.1.45.8.1.17.1.23 | ColumnwlanClientHTStatsTxFramesMCS6 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 6. |
| 1.3.6.1.4.1.45.8.1.17.1.24 | ColumnwlanClientHTStatsTxFramesMCS7 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 7. |
| 1.3.6.1.4.1.45.8.1.17.1.25 | ColumnwlanClientHTStatsTxFramesMCS8 | read-only | current | This attribute shows the number of data frames that were transmitted at MCS 8. |
| 1.3.6.1.4.1.45.8.1.17.1.26 | ColumnwlanClientHTStatsTxFramesMCS9 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 9. |
| 1.3.6.1.4.1.45.8.1.17.1.27 | ColumnwlanClientHTStatsTxFramesMCS10 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 10. |
| 1.3.6.1.4.1.45.8.1.17.1.28 | ColumnwlanClientHTStatsTxFramesMCS11 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 11. |
| 1.3.6.1.4.1.45.8.1.17.1.29 | ColumnwlanClientHTStatsTxFramesMCS12 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 12. |
| 1.3.6.1.4.1.45.8.1.17.1.30 | ColumnwlanClientHTStatsTxFramesMCS13 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 13. |
| 1.3.6.1.4.1.45.8.1.17.1.31 | ColumnwlanClientHTStatsTxFramesMCS14 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 14. |
| 1.3.6.1.4.1.45.8.1.17.1.32 | ColumnwlanClientHTStatsTxFramesMCS15 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 15. |
| 1.3.6.1.4.1.45.8.1.17.1.33 | ColumnwlanClientHTStatsRxBandwidth | read-only | current | This attribute shows the bandwidth the access point used with the last received frame: 20 MHz (1) or 40 MHz (2). |
| 1.3.6.1.4.1.45.8.1.17.1.34 | ColumnwlanClientHTStatsRxGuardInterval | read-only | current | This attribute shows the length of the guard interval the access point used with last received frame: long (1) or short (2). |
| 1.3.6.1.4.1.45.8.1.17.1.35 | ColumnwlanClientHTStatsTxBandwidth | read-only | current | This attribute shows the bandwidth the client used for transmitting the last frame: 20 MHz (1) or 40 MHz (2). |
| 1.3.6.1.4.1.45.8.1.17.1.36 | ColumnwlanClientHTStatsTxGuardInterval | read-only | current | This attribute shows the length of the guard interval the client used for transmitting the last frame: long (1) or short (2). |
| 1.3.6.1.4.1.45.8.1.17.1.37 | ColumnwlanClientHTStatsRxFramesMCS16 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 16. |
| 1.3.6.1.4.1.45.8.1.17.1.38 | ColumnwlanClientHTStatsRxFramesMCS17 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 17. |
| 1.3.6.1.4.1.45.8.1.17.1.39 | ColumnwlanClientHTStatsRxFramesMCS18 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 18. |
| 1.3.6.1.4.1.45.8.1.17.1.40 | ColumnwlanClientHTStatsRxFramesMCS19 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 19. |
| 1.3.6.1.4.1.45.8.1.17.1.41 | ColumnwlanClientHTStatsRxFramesMCS20 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 20. |
| 1.3.6.1.4.1.45.8.1.17.1.42 | ColumnwlanClientHTStatsRxFramesMCS21 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 21. |
| 1.3.6.1.4.1.45.8.1.17.1.43 | ColumnwlanClientHTStatsRxFramesMCS22 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 22. |
| 1.3.6.1.4.1.45.8.1.17.1.44 | ColumnwlanClientHTStatsRxFramesMCS23 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 23. |
| 1.3.6.1.4.1.45.8.1.17.1.45 | ColumnwlanClientHTStatsTxFramesMCS16 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 16. |
| 1.3.6.1.4.1.45.8.1.17.1.46 | ColumnwlanClientHTStatsTxFramesMCS17 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 17. |
| 1.3.6.1.4.1.45.8.1.17.1.47 | ColumnwlanClientHTStatsTxFramesMCS18 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 18. |
| 1.3.6.1.4.1.45.8.1.17.1.48 | ColumnwlanClientHTStatsTxFramesMCS19 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 19. |
| 1.3.6.1.4.1.45.8.1.17.1.49 | ColumnwlanClientHTStatsTxFramesMCS20 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 20. |
| 1.3.6.1.4.1.45.8.1.17.1.50 | ColumnwlanClientHTStatsTxFramesMCS21 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 21. |
| 1.3.6.1.4.1.45.8.1.17.1.51 | ColumnwlanClientHTStatsTxFramesMCS22 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 22. |
| 1.3.6.1.4.1.45.8.1.17.1.52 | ColumnwlanClientHTStatsTxFramesMCS23 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 23. |
| 1.3.6.1.4.1.45.8.1.17.1.53 | ColumnwlanClientHTStatsIfIndex | read-only | current | IfIndex of the client interface. |
| 1.3.6.1.4.1.45.8.1.18 | TablewlanWDSHTStatsTable | not-accessible | current | The wlanWDSHTStatsTable contains additional statistical data about 802.11n HT frames for WDS links. Each entry corresponds to an wlanWDSTable entry. Entries ca… |
| 1.3.6.1.4.1.45.8.1.18.1 | RowwlanWDSHTStatsEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.18.1.1 | ColumnwlanWDSHTStatsRxFramesMCS0 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 0. |
| 1.3.6.1.4.1.45.8.1.18.1.2 | ColumnwlanWDSHTStatsRxFramesMCS1 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 1. |
| 1.3.6.1.4.1.45.8.1.18.1.3 | ColumnwlanWDSHTStatsRxFramesMCS2 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 2. |
| 1.3.6.1.4.1.45.8.1.18.1.4 | ColumnwlanWDSHTStatsRxFramesMCS3 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 3. |
| 1.3.6.1.4.1.45.8.1.18.1.5 | ColumnwlanWDSHTStatsRxFramesMCS4 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 4. |
| 1.3.6.1.4.1.45.8.1.18.1.6 | ColumnwlanWDSHTStatsRxFramesMCS5 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 5. |
| 1.3.6.1.4.1.45.8.1.18.1.7 | ColumnwlanWDSHTStatsRxFramesMCS6 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 6. |
| 1.3.6.1.4.1.45.8.1.18.1.8 | ColumnwlanWDSHTStatsRxFramesMCS7 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 7. |
| 1.3.6.1.4.1.45.8.1.18.1.9 | ColumnwlanWDSHTStatsRxFramesMCS8 | read-only | current | This attribute shows the number of data frames that were received at MCS 8. |
| 1.3.6.1.4.1.45.8.1.18.1.10 | ColumnwlanWDSHTStatsRxFramesMCS9 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 9. |
| 1.3.6.1.4.1.45.8.1.18.1.11 | ColumnwlanWDSHTStatsRxFramesMCS10 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 10. |
| 1.3.6.1.4.1.45.8.1.18.1.12 | ColumnwlanWDSHTStatsRxFramesMCS11 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 11. |
| 1.3.6.1.4.1.45.8.1.18.1.13 | ColumnwlanWDSHTStatsRxFramesMCS12 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 12. |
| 1.3.6.1.4.1.45.8.1.18.1.14 | ColumnwlanWDSHTStatsRxFramesMCS13 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 13. |
| 1.3.6.1.4.1.45.8.1.18.1.15 | ColumnwlanWDSHTStatsRxFramesMCS14 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 14. |
| 1.3.6.1.4.1.45.8.1.18.1.16 | ColumnwlanWDSHTStatsRxFramesMCS15 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 15. |
| 1.3.6.1.4.1.45.8.1.18.1.17 | ColumnwlanWDSHTStatsTxFramesMCS0 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 0. |
| 1.3.6.1.4.1.45.8.1.18.1.18 | ColumnwlanWDSHTStatsTxFramesMCS1 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 1. |
| 1.3.6.1.4.1.45.8.1.18.1.19 | ColumnwlanWDSHTStatsTxFramesMCS2 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 2. |
| 1.3.6.1.4.1.45.8.1.18.1.20 | ColumnwlanWDSHTStatsTxFramesMCS3 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 3. |
| 1.3.6.1.4.1.45.8.1.18.1.21 | ColumnwlanWDSHTStatsTxFramesMCS4 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 4. |
| 1.3.6.1.4.1.45.8.1.18.1.22 | ColumnwlanWDSHTStatsTxFramesMCS5 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 5. |
| 1.3.6.1.4.1.45.8.1.18.1.23 | ColumnwlanWDSHTStatsTxFramesMCS6 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 6. |
| 1.3.6.1.4.1.45.8.1.18.1.24 | ColumnwlanWDSHTStatsTxFramesMCS7 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 7. |
| 1.3.6.1.4.1.45.8.1.18.1.25 | ColumnwlanWDSHTStatsTxFramesMCS8 | read-only | current | This attribute shows the number of data frames that were transmitted at MCS 8. |
| 1.3.6.1.4.1.45.8.1.18.1.26 | ColumnwlanWDSHTStatsTxFramesMCS9 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 9. |
| 1.3.6.1.4.1.45.8.1.18.1.27 | ColumnwlanWDSHTStatsTxFramesMCS10 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 10. |
| 1.3.6.1.4.1.45.8.1.18.1.28 | ColumnwlanWDSHTStatsTxFramesMCS11 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 11. |
| 1.3.6.1.4.1.45.8.1.18.1.29 | ColumnwlanWDSHTStatsTxFramesMCS12 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 12. |
| 1.3.6.1.4.1.45.8.1.18.1.30 | ColumnwlanWDSHTStatsTxFramesMCS13 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 13. |
| 1.3.6.1.4.1.45.8.1.18.1.31 | ColumnwlanWDSHTStatsTxFramesMCS14 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 14. |
| 1.3.6.1.4.1.45.8.1.18.1.32 | ColumnwlanWDSHTStatsTxFramesMCS15 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 15. |
| 1.3.6.1.4.1.45.8.1.18.1.33 | ColumnwlanWDSHTStatsRxBandwidth | read-only | current | This attribute shows the bandwidth the remote side used with the last received frame: 20 MHz (1) or 40 MHz (2). |
| 1.3.6.1.4.1.45.8.1.18.1.34 | ColumnwlanWDSHTStatsRxGuardInterval | read-only | current | This attribute shows the length of the guard interval the remote side used with the last received frame: long (1) or short (2). |
| 1.3.6.1.4.1.45.8.1.18.1.35 | ColumnwlanWDSHTStatsTxBandwidth | read-only | current | This attribute shows the bandwidth the local side used for transmitting the last frame: 20 MHz (1) or 40 MHz (2). |
| 1.3.6.1.4.1.45.8.1.18.1.36 | ColumnwlanWDSHTStatsTxGuardInterval | read-only | current | This attribute shows the length of the guard interval the local side used for transmitting the last frame: long (1) or short (2). |
| 1.3.6.1.4.1.45.8.1.18.1.37 | ColumnwlanWDSHTStatsRxFramesMCS16 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 16. |
| 1.3.6.1.4.1.45.8.1.18.1.38 | ColumnwlanWDSHTStatsRxFramesMCS17 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 17. |
| 1.3.6.1.4.1.45.8.1.18.1.39 | ColumnwlanWDSHTStatsRxFramesMCS18 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 18. |
| 1.3.6.1.4.1.45.8.1.18.1.40 | ColumnwlanWDSHTStatsRxFramesMCS19 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 19. |
| 1.3.6.1.4.1.45.8.1.18.1.41 | ColumnwlanWDSHTStatsRxFramesMCS20 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 20. |
| 1.3.6.1.4.1.45.8.1.18.1.42 | ColumnwlanWDSHTStatsRxFramesMCS21 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 21. |
| 1.3.6.1.4.1.45.8.1.18.1.43 | ColumnwlanWDSHTStatsRxFramesMCS22 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 22. |
| 1.3.6.1.4.1.45.8.1.18.1.44 | ColumnwlanWDSHTStatsRxFramesMCS23 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 23. |
| 1.3.6.1.4.1.45.8.1.18.1.45 | ColumnwlanWDSHTStatsTxFramesMCS16 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 16. |
| 1.3.6.1.4.1.45.8.1.18.1.46 | ColumnwlanWDSHTStatsTxFramesMCS17 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 17. |
| 1.3.6.1.4.1.45.8.1.18.1.47 | ColumnwlanWDSHTStatsTxFramesMCS18 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 18. |
| 1.3.6.1.4.1.45.8.1.18.1.48 | ColumnwlanWDSHTStatsTxFramesMCS19 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 19. |
| 1.3.6.1.4.1.45.8.1.18.1.49 | ColumnwlanWDSHTStatsTxFramesMCS20 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 20. |
| 1.3.6.1.4.1.45.8.1.18.1.50 | ColumnwlanWDSHTStatsTxFramesMCS21 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 21. |
| 1.3.6.1.4.1.45.8.1.18.1.51 | ColumnwlanWDSHTStatsTxFramesMCS22 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 22. |
| 1.3.6.1.4.1.45.8.1.18.1.52 | ColumnwlanWDSHTStatsTxFramesMCS23 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 23. |
| 1.3.6.1.4.1.45.8.1.19 | TablewlanLinkTestHTStatsTable | not-accessible | current | The wlanLinkTestHTStatsTable contains additional statistical data about 802.11n HT frames for WDS links. Each entry corresponds to an wlanWDSTable entry. Entri… |
| 1.3.6.1.4.1.45.8.1.19.1 | RowwlanLinkTestHTStatsEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.19.1.1 | ColumnwlanLinkTestHTStatsIfIndex | read-only | current | The interface index of the corresponding bridge interface. |
| 1.3.6.1.4.1.45.8.1.19.1.2 | ColumnwlanLinkTestHTStatsRxFramesMCS0 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 0. |
| 1.3.6.1.4.1.45.8.1.19.1.3 | ColumnwlanLinkTestHTStatsRxFramesMCS1 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 1. |
| 1.3.6.1.4.1.45.8.1.19.1.4 | ColumnwlanLinkTestHTStatsRxFramesMCS2 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 2. |
| 1.3.6.1.4.1.45.8.1.19.1.5 | ColumnwlanLinkTestHTStatsRxFramesMCS3 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 3. |
| 1.3.6.1.4.1.45.8.1.19.1.6 | ColumnwlanLinkTestHTStatsRxFramesMCS4 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 4. |
| 1.3.6.1.4.1.45.8.1.19.1.7 | ColumnwlanLinkTestHTStatsRxFramesMCS5 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 5. |
| 1.3.6.1.4.1.45.8.1.19.1.8 | ColumnwlanLinkTestHTStatsRxFramesMCS6 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 6. |
| 1.3.6.1.4.1.45.8.1.19.1.9 | ColumnwlanLinkTestHTStatsRxFramesMCS7 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 7. |
| 1.3.6.1.4.1.45.8.1.19.1.10 | ColumnwlanLinkTestHTStatsRxFramesMCS8 | read-only | current | This attribute shows the number of data frames that were received at MCS 8. |
| 1.3.6.1.4.1.45.8.1.19.1.11 | ColumnwlanLinkTestHTStatsRxFramesMCS9 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 9. |
| 1.3.6.1.4.1.45.8.1.19.1.12 | ColumnwlanLinkTestHTStatsRxFramesMCS10 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 10. |
| 1.3.6.1.4.1.45.8.1.19.1.13 | ColumnwlanLinkTestHTStatsRxFramesMCS11 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 11. |
| 1.3.6.1.4.1.45.8.1.19.1.14 | ColumnwlanLinkTestHTStatsRxFramesMCS12 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 12. |
| 1.3.6.1.4.1.45.8.1.19.1.15 | ColumnwlanLinkTestHTStatsRxFramesMCS13 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 13. |
| 1.3.6.1.4.1.45.8.1.19.1.16 | ColumnwlanLinkTestHTStatsRxFramesMCS14 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 14. |
| 1.3.6.1.4.1.45.8.1.19.1.17 | ColumnwlanLinkTestHTStatsRxFramesMCS15 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 15. |
| 1.3.6.1.4.1.45.8.1.19.1.18 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS0 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 0. |
| 1.3.6.1.4.1.45.8.1.19.1.19 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS1 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 1. |
| 1.3.6.1.4.1.45.8.1.19.1.20 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS2 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 2. |
| 1.3.6.1.4.1.45.8.1.19.1.21 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS3 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 3. |
| 1.3.6.1.4.1.45.8.1.19.1.22 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS4 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 4. |
| 1.3.6.1.4.1.45.8.1.19.1.23 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS5 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 5. |
| 1.3.6.1.4.1.45.8.1.19.1.24 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS6 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 6. |
| 1.3.6.1.4.1.45.8.1.19.1.25 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS7 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 7. |
| 1.3.6.1.4.1.45.8.1.19.1.26 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS8 | read-only | current | This attribute shows the number of data frames that were transmitted at MCS 8. |
| 1.3.6.1.4.1.45.8.1.19.1.27 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS9 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 9. |
| 1.3.6.1.4.1.45.8.1.19.1.28 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS10 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 10. |
| 1.3.6.1.4.1.45.8.1.19.1.29 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS11 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 11. |
| 1.3.6.1.4.1.45.8.1.19.1.30 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS12 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 12. |
| 1.3.6.1.4.1.45.8.1.19.1.31 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS13 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 13. |
| 1.3.6.1.4.1.45.8.1.19.1.32 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS14 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 14. |
| 1.3.6.1.4.1.45.8.1.19.1.33 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS15 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 15. |
| 1.3.6.1.4.1.45.8.1.19.1.34 | ColumnwlanLinkTestHTStatsBandwidthLocal | read-only | current | This attribute shows the bandwidth the remote side used: 20 MHz (1) or 40 MHz (2). |
| 1.3.6.1.4.1.45.8.1.19.1.35 | ColumnwlanLinkTestHTStatsGuardIntervalLocal | read-only | current | This attribute shows the length of the guard interval the remote side used: long (1) or short (2). |
| 1.3.6.1.4.1.45.8.1.19.1.36 | ColumnwlanLinkTestHTStatsRSSI1Local | read-only | current | This attribute shows the received signal strength on the first receiver in dBm. |
| 1.3.6.1.4.1.45.8.1.19.1.37 | ColumnwlanLinkTestHTStatsRSSI2Local | read-only | current | This attribute shows the received signal strength on the second receiver in dBm. |
| 1.3.6.1.4.1.45.8.1.19.1.38 | ColumnwlanLinkTestHTStatsRSSI3Local | read-only | current | This attribute shows the received signal strength on the third receiver in dBm. |
| 1.3.6.1.4.1.45.8.1.19.1.39 | ColumnwlanLinkTestHTStatsBandwidthRemote | read-only | current | This attribute shows the bandwidth the local side used for transmitting: 20 MHz (1) or 40 MHz (2). |
| 1.3.6.1.4.1.45.8.1.19.1.40 | ColumnwlanLinkTestHTStatsGuardIntervalRemote | read-only | current | This attribute shows the length of the guard interval the local side used for transmitting: long (1) or short (2). |
| 1.3.6.1.4.1.45.8.1.19.1.41 | ColumnwlanLinkTestHTStatsRSSI1Remote | read-only | current | This attribute shows the received signal strength on the first receiver on the remote side in dBm. |
| 1.3.6.1.4.1.45.8.1.19.1.42 | ColumnwlanLinkTestHTStatsRSSI2Remote | read-only | current | This attribute shows the received signal strength on the second receiver on the remote side in dBm. |
| 1.3.6.1.4.1.45.8.1.19.1.43 | ColumnwlanLinkTestHTStatsRSSI3Remote | read-only | current | This attribute shows the received signal strength on the third receiver on the remote side in dBm. |
| 1.3.6.1.4.1.45.8.1.19.1.44 | ColumnwlanLinkTestHTStatsRxFramesMCS16 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 16. |
| 1.3.6.1.4.1.45.8.1.19.1.45 | ColumnwlanLinkTestHTStatsRxFramesMCS17 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 17. |
| 1.3.6.1.4.1.45.8.1.19.1.46 | ColumnwlanLinkTestHTStatsRxFramesMCS18 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 18. |
| 1.3.6.1.4.1.45.8.1.19.1.47 | ColumnwlanLinkTestHTStatsRxFramesMCS19 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 19. |
| 1.3.6.1.4.1.45.8.1.19.1.48 | ColumnwlanLinkTestHTStatsRxFramesMCS20 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 20. |
| 1.3.6.1.4.1.45.8.1.19.1.49 | ColumnwlanLinkTestHTStatsRxFramesMCS21 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 21. |
| 1.3.6.1.4.1.45.8.1.19.1.50 | ColumnwlanLinkTestHTStatsRxFramesMCS22 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 22. |
| 1.3.6.1.4.1.45.8.1.19.1.51 | ColumnwlanLinkTestHTStatsRxFramesMCS23 | read-only | current | This attribute shows the number of HT data frames that were received at MCS 23. |
| 1.3.6.1.4.1.45.8.1.19.1.52 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS16 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 16. |
| 1.3.6.1.4.1.45.8.1.19.1.53 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS17 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 17. |
| 1.3.6.1.4.1.45.8.1.19.1.54 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS18 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 18. |
| 1.3.6.1.4.1.45.8.1.19.1.55 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS19 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 19. |
| 1.3.6.1.4.1.45.8.1.19.1.56 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS20 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 20. |
| 1.3.6.1.4.1.45.8.1.19.1.57 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS21 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 21. |
| 1.3.6.1.4.1.45.8.1.19.1.58 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS22 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 22. |
| 1.3.6.1.4.1.45.8.1.19.1.59 | ColumnwlanLinkTestHTStatsRxFramesRemoteMCS23 | read-only | current | This attribute shows the number of HT data frames that were transmitted at MCS 23. |
| 1.3.6.1.4.1.45.8.1.20 | NodewlanWDSNotification | |||
| 1.3.6.1.4.1.45.8.1.20.1 | NotificationwlanWDSLinkOperState | current | This notification is triggered whenever the connection state of the bridge link changes, i.e. link connection is lost, or link connection is restored. | |
| 1.3.6.1.4.1.45.8.1.20.2 | NotificationwlanWDSLinkConfigScan | current | This notification is thrown whenever the bridge link auto-configuration scanning state changes. | |
| 1.3.6.1.4.1.45.8.1.20.3 | NotificationwlanWDSPeerConfigSetup | current | This notification is thrown whenever the bridge link auto-configuration setup state changes. | |
| 1.3.6.1.4.1.45.8.1.20.4 | NotificationwlanWDSLinkLock | current | This notification is triggered whenever the lock state of the bridge link changes. | |
| 1.3.6.1.4.1.45.8.1.21 | NodewlanGlobal | |||
| 1.3.6.1.4.1.45.8.1.21.1 | ScalarwlanGlobalEnable | read-only | current | This is a global WLAN switch to enable/disable all WLAN cards (can be used for a WLAN button) |
| 1.3.6.1.4.1.45.8.1.21.2 | ScalarwlanGlobalDebugType | read-write | current | Wireless LAN degugging type. With type common(1) debugging messages of authentication, access_point, bridge and client handling will be shown. With type authen… |
| 1.3.6.1.4.1.45.8.1.21.3 | ScalarwlanGlobalDebugLevel | read-write | current | Wireless LAN degugging verbosity level. With a higher value more debugging information will be created. Default is normal(2). |
| 1.3.6.1.4.1.45.8.1.21.4 | ScalarwlanGlobalAdminStatus | read-write | current | Wireless LAN global AdminStatus. The AP could be used unmanaged(1) and must therefore be configured directly or managed(2) by a WLAN controller. Default is unm… |
| 1.3.6.1.4.1.45.8.1.21.5 | ScalarwlanGlobalOperStatus | read-only | current | Wireless LAN global OperStatus. This variable shows the state of the AP where undefined(1) is the initial state when the AP comes up. The AP is in the managed_… |
| 1.3.6.1.4.1.45.8.1.21.6 | ScalarwlanGlobalScanResultsMaxAge | read-write | current | If a scan result wasn't seen for so many seconds, it will be removed from wlanScanResultsTable. |
| 1.3.6.1.4.1.45.8.1.22 | TablewlanWMMTable | not-accessible | current | Describes a WLAN WMM Access category settings |
| 1.3.6.1.4.1.45.8.1.22.1 | RowwlanWMMEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.22.1.1 | ColumnwlanWMMAccCat | read-only | current | Access category type, each category is mandatory for a wlanIf. An access category (AC) is a label for the common set of enhanced distributed channel access (ED… |
| 1.3.6.1.4.1.45.8.1.22.1.2 | ColumnwlanWMMwlanIf | read-only | current | Radio index the AC belongs to. |
| 1.3.6.1.4.1.45.8.1.22.1.3 | ColumnwlanWMMaCWmin | read-write | current | Minimum size of contention window. for AC_BK and AC_BE wlanWMMaCWmin = wlanIfCWmin, for AC_VI wlanWMMaCWmin = (wlanIfCWmin-1)/2, for AC_VO wlanWMMaCWmin = (wla… |
| 1.3.6.1.4.1.45.8.1.22.1.4 | ColumnwlanWMMaCWmax | read-write | current | Maximum size of contention window. for AC_BK wlanWMMaCWmax = wlanIfCWmax, for AC_BE wlanWMMaCWmax = 4*wlanIfCWmin + 3, for AC_VI wlanWMMaCWmax = wlanIfCWmin, f… |
| 1.3.6.1.4.1.45.8.1.22.1.5 | ColumnwlanWMMAifsn | read-write | current | Arbitration Inter-Frame Space Number (AIFSN) for this Access category. |
| 1.3.6.1.4.1.45.8.1.22.1.6 | ColumnwlanWMMTxopLimitb | read-write | current | 802.11b mode Transmit Opportunity Limit. |
| 1.3.6.1.4.1.45.8.1.22.1.7 | ColumnwlanWMMTxopLimitg | read-write | current | 802.11g mode Transmit Opportunity Limit. |
| 1.3.6.1.4.1.45.8.1.22.1.8 | ColumnwlanWMMAckPolicy | read-write | current | Ack policy for this Access category (default value is 'ack(1)'). |
| 1.3.6.1.4.1.45.8.1.22.1.9 | ColumnwlanWMMACM | read-write | current | ACM (admission control) policy for this Access category i (default value is 'disabled(2)'). |
| 1.3.6.1.4.1.45.8.1.22.1.10 | ColumnwlanWMMType | read-only | current | Type to which this wlanWMMEntry corresponds. Type access_point means the own parameters for WMM are changed. The entries with type station will be provided to … |
| 1.3.6.1.4.1.45.8.1.23 | TablewlanIfFeatureTable | not-accessible | current | This table lists all feature of a wireless card. The supported features depends on the vendor and wireless chipset. |
| 1.3.6.1.4.1.45.8.1.23.1 | RowwlanIfFeatureEntry | not-accessible | current | |
| 1.3.6.1.4.1.45.8.1.23.1.1 | ColumnwlanIfFeatureWlanIf | read-only | current | Wireless card interface index the table belongs. |
| 1.3.6.1.4.1.45.8.1.23.1.2 | ColumnwlanIfFeatureOperatingBands | read-only | current | This variable says which bands the wireless card supports. Default is 2.4 and 5 GHZ. |
| 1.3.6.1.4.1.45.8.1.23.1.3 | ColumnwlanIfFeatureAntennaDiversity | read-only | current | This variable says which kind of antenna diversity the wireless card supports. Default is none. |
| 1.3.6.1.4.1.45.8.1.23.1.4 | ColumnwlanIfFeatureTxPowerMin | read-only | current | The minimal value of the TX power the wireless card supports. |
| 1.3.6.1.4.1.45.8.1.23.1.5 | ColumnwlanIfFeatureTxPowerMax | read-only | current | The maximal value of the TX power the wireless card supports. |
| 1.3.6.1.4.1.45.8.1.23.1.6 | ColumnwlanIfFeatureTxPowerFixedStepsList | read-only | current | This variable shows the available TX Power values in dBm seperated by commas. |
| 1.3.6.1.4.1.45.8.1.23.1.7 | ColumnwlanIfFeatureFrameCompression | read-only | current | This variable says if the wireless card supports frame compression or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.8 | ColumnwlanIfFeatureFrameConcatenation | read-only | current | This variable says if the wireless card supports frame concatination or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.9 | ColumnwlanIfFeaturePiggybackAck | read-only | current | This variable says if the wireless card supports piggyback ACKs or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.10 | ColumnwlanIfFeatureDirectLink | read-only | current | This variable says if the wireless card supports direct links or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.11 | ColumnwlanIfFeatureLinkDistance | read-only | current | This variable says if the wireless card supports a configurable link distance or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.12 | ColumnwlanIfFeatureShortRetries | read-only | current | This variable says if the wireless card supports the configuration of the short retry value or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.13 | ColumnwlanIfFeatureLongRetries | read-only | current | This variable says if the wireless card supports the configuration of the long retry value or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.14 | ColumnwlanIfFeatureFragThreshold | read-only | current | This variable says if the wireless card supports the configuration of the fragmentation threshold value or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.15 | ColumnwlanIfFeatureCCAMode | read-only | current | This variable says if the wireless card supports the configuration of the CCA mode or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.16 | ColumnwlanIfFeatureEdThreshold | read-only | current | This variable says if the wireless card supports the configuration of the energy detection threshold value or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.17 | ColumnwlanIfFeatureCWMin | read-only | current | This variable says if the wireless card supports the configuration of the minimal contention window or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.18 | ColumnwlanIfFeatureCWMax | read-only | current | This variable says if the wireless card supports the configuration of the maximal contention window or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.19 | ColumnwlanIfFeatureRxLifetime | read-only | current | This variable says if the wireless card supports the configuration of the receive packet lifetime or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.20 | ColumnwlanIfFeatureTxLifetime | read-only | current | This variable says if the wireless card supports the configuration of the transmit packet lifetime or not. Default is false. |
| 1.3.6.1.4.1.45.8.1.23.1.21 | ColumnwlanIfFeatureSkipModes | read-only | current | This variable says which modes of the WlanIfSkipChannels the wireless card supports. Default is client24ghz. |
| 1.3.6.1.4.1.45.8.1.23.1.22 | ColumnwlanIfFeatureSupportedModes | read-only | current | This variable shows the supported 802.11 modes |
| 1.3.6.1.4.1.45.8.1.23.1.23 | ColumnwlanIfFeatureSpatialStreams | read-only | current | This variable shows the maximum number of supported spatial streams |
| 1.3.6.1.4.1.45.8.1.23.1.30 | ColumnwlanIfFeatureMaxVSS | read-only | current | This attribute indicates the maximum number of service sets that may be created per radio module. |
| 1.3.6.1.4.1.45.8.1.23.1.31 | ColumnwlanIfFeatureMaxWDS | read-only | current | This attribute indicates the maximum number of WDS links that may be created per radio module. |
| 1.3.6.1.4.1.45.8.1.23.1.32 | ColumnwlanIfFeatureMaxClient | read-only | current | This attribute indicates the maximum number of client instances that may be created per radio module. |
| 1.3.6.1.4.1.45.8.1.23.1.33 | ColumnwlanIfFeatureMaxStations | read-only | current | Maximum number of stations the station database can hold. |
| 1.3.6.1.4.1.272.4.59 | IdentitywlanMIB | MIB for wlan subsystem |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| WlanRate | INTEGER (0..600) | current | This type is used to represent WLAN data rates in 500 Kbps units. |
| WlanRSSI | INTEGER (-110..0) | current | This type is used to represent receiver input levels in dBm. |