BIANCA-BRICK-X21-MIB
27 objects
No module-level DESCRIPTION found.
Imported Objects
| BINTEC-MIB MISSING | Date HexValue |
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.272 | Nodebintec | |||
| 1.3.6.1.4.1.272.4 | Nodebibo | |||
| 1.3.6.1.4.1.272.4.10 | Nodex21 | |||
| 1.3.6.1.4.1.272.4.10.1 | Tablex21IfTable | not-accessible | mandatory | The x21IfTable contains information relating to the interfaces found on the system. Each entry corresponds to a connected X21 interface. Entries can only be ad… |
| 1.3.6.1.4.1.272.4.10.1.1 | Rowx21IfEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.10.1.1.1 | Columnx21IfIndex | read-only | mandatory | Unique index of the X21 interface. |
| 1.3.6.1.4.1.272.4.10.1.1.2 | Columnx21IfL1State | read-only | mandatory | The X21 physical layer state dn(1) physical layer is inactive; up(2) physical layer is active; |
| 1.3.6.1.4.1.272.4.10.1.1.3 | Columnx21IfL1Mode | read-write | mandatory | The physical layer (layer 1) mode. When configured as DCE(2) the X21 interface provides the clock. |
| 1.3.6.1.4.1.272.4.10.1.1.4 | Columnx21IfIfLeads | read-write | mandatory | The value of IfLeads has influence on the state of the physical layer (L1State). When configured as IfLeads=enabled(1), the state of the physical layer depends… |
| 1.3.6.1.4.1.272.4.10.1.1.5 | Columnx21IfSpeed | read-write | mandatory | The X21 interface speed in bits per second. The range can be configured between 2Mbits and 2400 Bits per second. |
| 1.3.6.1.4.1.272.4.10.1.1.6 | Columnx21IfL2Mode | read-write | mandatory | The layer 2 mode. This value has influence on the HDLC address field (first byte of a HDCL frame). When configured as DTE(1) the address in a command frame is … |
| 1.3.6.1.4.1.272.4.10.1.1.7 | Columnx21IfSpeedReal | read-only | mandatory | The measured X21 interface speed in bits per second. |
| 1.3.6.1.4.1.272.4.10.1.1.8 | Columnx21IfRxPackets | read-only | mandatory | Count of received valid Frames. |
| 1.3.6.1.4.1.272.4.10.1.1.9 | Columnx21IfRxOctets | read-only | mandatory | Count of received bytes. |
| 1.3.6.1.4.1.272.4.10.1.1.10 | Columnx21IfTxPackets | read-only | mandatory | Count of transmitted valid Frames. |
| 1.3.6.1.4.1.272.4.10.1.1.11 | Columnx21IfTxOctets | read-only | mandatory | Count of transmitted bytes. |
| 1.3.6.1.4.1.272.4.10.1.1.12 | Columnx21IfRxResets | read-only | mandatory | Count of receiver resets. Under rare circumstances it might be necessary to reset the receiver to work properly. |
| 1.3.6.1.4.1.272.4.10.1.1.13 | Columnx21IfRxAborts | read-only | mandatory | Count of receiver aborts. The sender of a frame can indicate a frame as aborted with a special Abort sequence. |
| 1.3.6.1.4.1.272.4.10.1.1.14 | Columnx21IfRxOverruns | read-only | mandatory | Count of receiver overruns. If the X21 card is unable to grant sufficiently soon/often the bus, the 32-character RxFIFO may fill up. This leads to loss of data. |
| 1.3.6.1.4.1.272.4.10.1.1.15 | Columnx21IfRxCRCErrors | read-only | mandatory | Count of corrupted frames. Errors due to interference on the X21 cable. |
| 1.3.6.1.4.1.272.4.10.1.1.16 | Columnx21IfRxGiantFrames | read-only | mandatory | Count of received frames with illegal framesize. This can occur if a frame delimiter is destroyed. |
| 1.3.6.1.4.1.272.4.10.1.1.17 | Columnx21IfTxResets | read-only | mandatory | Count of transmitter resets. Under rare circumstances it might be necessary to reset the transmitter to work properly. |
| 1.3.6.1.4.1.272.4.10.1.1.18 | Columnx21IfTxAborts | read-only | mandatory | Count of transmitter aborts. While sending a frame it might be necessary to indicate this frame as aborted. In this case the receiver regards this frame as ill… |
| 1.3.6.1.4.1.272.4.10.1.1.19 | Columnx21IfTxUnderruns | read-only | mandatory | Count of transmitter underruns. The serial data for the X21 card is supplied too slowly. |
| 1.3.6.1.4.1.272.4.10.1.1.20 | Columnx21IfTxGiantFrames | read-only | mandatory | Count of transmitted frames with illegal framesize. This can occur if an upper module creates packets with more than the maximum allowed packet size. |
| 1.3.6.1.4.1.272.4.10.1.1.21 | Columnx21IfIfReSyncs | read-only | mandatory | Count of interface resynchronization. Under rare circumstances it might be necessary to resynchronize the physical interface to work properly. |
| 1.3.6.1.4.1.272.4.10.1.1.22 | Columnx21IfBundle | read-write | mandatory | Index of the bundle to aggregate multiple Channels to one interface. |