BINTEC-IPEXT-MIB
349 objects
The MIB module for IP extended configuration and status.
Imported Objects
| BINTEC-MIB MISSING | biboip BitValue Date |
| IF-MIB | ifIndex |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | enterprises IpAddress |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 MODULE-IDENTITY NOTIFICATION-TYPE TimeTicks |
| SNMPv2-TC | DisplayString MacAddress TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.272.4.5.3 | TableipExtIfTable | not-accessible | current | The ipExtIfTable contains extended information related to IP and the interfaces found on the system. Entries can only be added or deleted by the system. |
| 1.3.6.1.4.1.272.4.5.3.1 | RowipExtIfEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.3.1.1 | ColumnipExtIfIndex | read-only | current | Unique interface index |
| 1.3.6.1.4.1.272.4.5.3.1.3 | ColumnipExtIfRipSend | read-write | current | specifies which versions of RIP messages are sent to that interface. Usually RIP messages are sent as broadcast, except this object is set to ripV2mcast. In th… |
| 1.3.6.1.4.1.272.4.5.3.1.4 | ColumnipExtIfRipReceive | read-write | current | specifies which versions of RIP messages are accepted from that interface. RIP V2 messages are received regardless if they are sent as broadcast or multicast. |
| 1.3.6.1.4.1.272.4.5.3.1.5 | ColumnipExtIfProxyArp | read-write | current | Switch for Proxy ARP on this interface. |
| 1.3.6.1.4.1.272.4.5.3.1.6 | ColumnipExtIfNat | read-write | current | This object can be used to switch NAT on and off for a specific interface. |
| 1.3.6.1.4.1.272.4.5.3.1.7 | ColumnipExtIfNatRmvFin | read-write | current | This object specifies, whether entries in the IpNatTable shall be removed, when TCP-FINS have been received and acknowledged in both directions, a TCP-RST has … |
| 1.3.6.1.4.1.272.4.5.3.1.8 | ColumnipExtIfNatTcpTimeout | read-write | current | TCP NAT entries vanish unconditionally after not being used for the amount of time specified by this object in seconds. |
| 1.3.6.1.4.1.272.4.5.3.1.9 | ColumnipExtIfNatOtherTimeout | read-write | current | Non-TCP NAT entries vanish unconditionally after not being used for the amount of time specified by this object in seconds. |
| 1.3.6.1.4.1.272.4.5.3.1.10 | ColumnipExtIfNatOutXlat | read-write | current | This object can be used to switch the outgoing address translation off. Then, all addresses are passed instead of being translated. The session mechanism remai… |
| 1.3.6.1.4.1.272.4.5.3.1.11 | ColumnipExtIfAccounting | read-write | current | Switch for accounting on the specified interface. An IP packet is being accounted, when this object is set to on for either the source or the destination inter… |
| 1.3.6.1.4.1.272.4.5.3.1.12 | ColumnipExtIfTcpSpoofing | read-write | current | Switch for TCP spoofing on this interface. TCP keepalive polls are answered by the BRICK to prevent unnecessary ISDN connections. Set this object to on for ISD… |
| 1.3.6.1.4.1.272.4.5.3.1.13 | ColumnipExtIfAccessAction | read-write | current | This object describes the action, that is done, when a packet received from the interface has been filtered out. When set to ignore, no action takes place. Whe… |
| 1.3.6.1.4.1.272.4.5.3.1.14 | ColumnipExtIfAccessReport | read-write | current | This object specifies, how a packed filtered by accesslists should be logged. When set to none, no logging takes place. When set to info, protocol, ip-addresse… |
| 1.3.6.1.4.1.272.4.5.3.1.15 | ColumnipExtIfOspf | read-write | current | Configure the OSPF status of this interface. Routing information about routes on passive and active interfaces is propagated on active interfaces. Only active … |
| 1.3.6.1.4.1.272.4.5.3.1.16 | ColumnipExtIfOspfMetric | read-write | current | Configure the metric calculation of OSPF interfaces. If set to auto the metric is calculated based on ifSpeed. If set to fixed the metric is taken from the osp… |
| 1.3.6.1.4.1.272.4.5.3.1.17 | ColumnipExtIfTcpCksum | read-write | current | Enable or disable the TCP checksum check for local packets received on the corresponding interface. Disabling the check may improve performance for some local … |
| 1.3.6.1.4.1.272.4.5.3.1.18 | ColumnipExtIfBackRtVerify | read-write | current | This object activates an additional check for incoming packets. If set to on, incoming packets are only accepted if return packets sent back to their source IP… |
| 1.3.6.1.4.1.272.4.5.3.1.19 | ColumnipExtIfRuleIndex | read-write | current | This object defines the index of the first access rule that is applied for incoming packets. If set to 0 or if there is no access rule with this index no acces… |
| 1.3.6.1.4.1.272.4.5.3.1.20 | ColumnipExtIfAuthentication | read-write | current | This object defines the authentication scheme used for incoming packets. |
| 1.3.6.1.4.1.272.4.5.3.1.21 | ColumnipExtIfAuthMode | read-write | current | This object defines the authentication mode. If set to strict each source IP address must be authenticated. If set to loose all source IP addresses are allowed… |
| 1.3.6.1.4.1.272.4.5.3.1.22 | ColumnipExtIfAuthLifeTime | read-write | current | This object defines the time in seconds a successful authentication is valid since the IP partner was authenticated. |
| 1.3.6.1.4.1.272.4.5.3.1.23 | ColumnipExtIfAuthKeepalive | read-write | current | This object defines the period between short authentications that are invisible to the user |
| 1.3.6.1.4.1.272.4.5.3.1.24 | ColumnipExtIfRouteAnnounce | read-write | current | This object defines the condition when routes on this interface are propagated by routing protocols. If set to up-only routes are only propagated if the operat… |
| 1.3.6.1.4.1.272.4.5.3.1.25 | ColumnipExtIfIpFragmentation | read-write | current | This object defines different modes used for fragmentation of IP datagrams greater than the MTU of the destination interface. If set to enabled (1) each IP dat… |
| 1.3.6.1.4.1.272.4.5.3.1.26 | ColumnipExtIfRerouting | read-write | current | This object enables or disables rerouting on this interface. The default value is enabled. If set to disabled, then only the better one route from two or more … |
| 1.3.6.1.4.1.272.4.5.3.1.27 | ColumnipExtIfBodRuleIndex | read-write | current | This object defines the index of the first rule used for Bandwidth on Demand (BOD) that is applied for incoming and/or outgoing traffic. If set to 0 or if ther… |
| 1.3.6.1.4.1.272.4.5.3.1.28 | ColumnipExtIfQosRuleIndex | read-write | current | This object defines the index of the first rule used for Qos (Qualtiy of Service) rules applied for IP traffic. If set to 0 or if there is no entry in the ipQo… |
| 1.3.6.1.4.1.272.4.5.3.1.29 | ColumnipExtIfIpsecAccounting | read-write | current | This object determines, whether packets which are en- or decapsulated by IPSec should be accounted with encapsulation header(ipsec) or without the encapsulatio… |
| 1.3.6.1.4.1.272.4.5.3.1.30 | ColumnipExtIfMulticast | read-write | current | Enable that multicast frames are accepted from that interface. |
| 1.3.6.1.4.1.272.4.5.3.1.31 | ColumnipExtIfNatSilentDeny | read-write | current | This object specifies - if NAT is enabled (see ipExtIfNat) - whether incoming IP packets not passed by the NAT barrier should answered with an ICMP Host Unreac… |
| 1.3.6.1.4.1.272.4.5.3.1.33 | ColumnipExtIfNatPPTPXlat | read-write | current | This object specifies - if NAT is enabled (see ipExtIfNat) - whether PPTP (point to point protocol) connections are translated. This is needed if there are mor… |
| 1.3.6.1.4.1.272.4.5.3.1.34 | ColumnipExtIfTcpMssClamping | read-write | current | This object specifies whether TCP MSS clamping is enabled on the interface. -1 disables clamping, 0 clamps the MSS depending on the interface MTU. A value > 0 … |
| 1.3.6.1.4.1.272.4.5.3.1.35 | ColumnipExtIfNbdgmRelayAddress | read-write | current | This object contains the destination IP address to which Netbios Datagram request are forwarded by the router. |
| 1.3.6.1.4.1.272.4.5.3.1.36 | ColumnipExtIfNatMaxSessions | read-write | current | This object limits the maximum number of NAT sessions on a interface. |
| 1.3.6.1.4.1.272.4.5.3.1.37 | ColumnipExtIfAllowedPeers | read-write | current | If this object is set to 'dhcpclients', the router refuses to exchange data with hosts which are not DHCP clients on this interface. If this object is set to '… |
| 1.3.6.1.4.1.272.4.5.3.1.38 | ColumnipExtIfNatFlush | read-write | current | If this object in enabled NAT-Flushing is done else not. NAT-Flushing means that the NAT Entries for this interface will be deleted in the case of an OperStatu… |
| 1.3.6.1.4.1.272.4.5.3.1.39 | ColumnipExtIfHttpRedirect | read-write | current | If not set to 'disabled' all HTTP requests on this interface will be directed either to the local HTTP daemon or HTTP proxy. |
| 1.3.6.1.4.1.272.4.5.3.1.40 | ColumnipExtIfWolRuleIndex | read-write | current | This object defines the index of the first rule used for Wake-On-LAN (WOL) that is applied for incoming and/or outgoing traffic. If set to 0 or if there is no … |
| 1.3.6.1.4.1.272.4.5.4 | TableipExtRtTable | not-accessible | current | The ipExtRtTable can be used in addition (not instead of) to the ipRouteTable to specify routing of IP datagrams. The selection of datagram-types is more speci… |
| 1.3.6.1.4.1.272.4.5.4.1 | RowipExtRtEntry | not-accessible | current | Each entry in the ipExtRtTable describes a set of IP datagrams and the destination interface for that set. Metric parameters allow for ordering of the differen… |
| 1.3.6.1.4.1.272.4.5.4.1.1 | ColumnipExtRtProtocol | read-write | current | This object specifies the value of the protocolfield in the ip header for all IP-datagrams belonging to the set. If this object is set to dont-verify, the valu… |
| 1.3.6.1.4.1.272.4.5.4.1.2 | ColumnipExtRtSrcIfIndex | read-write | current | This object specifies the source index of the IP-datagrams. If this object has a value other than 0, only datagrams received over the interface with the approp… |
| 1.3.6.1.4.1.272.4.5.4.1.3 | ColumnipExtRtSrcAddr | read-write | current | This object describes together with ipExtRtSrcMask the range of the source-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0… |
| 1.3.6.1.4.1.272.4.5.4.1.4 | ColumnipExtRtSrcMask | read-write | current | This object describes together with ipExtRtSrcAddr the range of the source-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0… |
| 1.3.6.1.4.1.272.4.5.4.1.5 | ColumnipExtRtSrcPort | read-write | current | This object describes together with ipExtRtSrcPortRange the range of source portnumbers of the IP-datagrams belonging to the set. All portnumbers between and i… |
| 1.3.6.1.4.1.272.4.5.4.1.6 | ColumnipExtRtSrcPortRange | read-write | current | This object describes together with ipExtRtSrcPort the range of source portnumbers of the IP-datagrams belonging to the set. All portnumbers between and includ… |
| 1.3.6.1.4.1.272.4.5.4.1.7 | ColumnipExtRtDstAddr | read-write | current | This object describes together with ipExtRtDstMask the range of the target-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0… |
| 1.3.6.1.4.1.272.4.5.4.1.8 | ColumnipExtRtDstMask | read-write | current | This object describes together with ipExtRtDstAddr the range of the target-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.0… |
| 1.3.6.1.4.1.272.4.5.4.1.9 | ColumnipExtRtDstPort | read-write | current | This object describes together with ipExtRtDstPortRange the range of target-portnumbers of the IP-datagrams belonging to the set. All portnumbers between and i… |
| 1.3.6.1.4.1.272.4.5.4.1.10 | ColumnipExtRtDstPortRange | read-write | current | This object describes together with ipExtRtDstPort the range of target-portnumbers of the IP-datagrams belonging to the set. All portnumbers between and includ… |
| 1.3.6.1.4.1.272.4.5.4.1.11 | ColumnipExtRtTos | read-write | current | This object describes together with ipExtRtTosMask the range of the Type of Service field (TOS) in the IP-header of the IP-datagrams belonging to the set. A TO… |
| 1.3.6.1.4.1.272.4.5.4.1.12 | ColumnipExtRtTosMask | read-write | current | This object describes together with ipExtRtTos the range of the Type of Service field (TOS) in the IP-header of the IP-datagrams belonging to the set. A TOS va… |
| 1.3.6.1.4.1.272.4.5.4.1.13 | ColumnipExtRtDstIfMode | read-write | current | This object describes different behavior depending on the ifOperStatus of the destination interface: dialup-wait: The route matches, when the ifOperStatus of t… |
| 1.3.6.1.4.1.272.4.5.4.1.14 | ColumnipExtRtDstIfIndex | read-write | current | This object specifies the destination interface for the IP-datagrams belonging to the set. If the value of this object is set to 0, the datagrams of the set ar… |
| 1.3.6.1.4.1.272.4.5.4.1.15 | ColumnipExtRtNextHop | read-write | current | This object is used on point-to-multipoint interfaces with indirect routes (see ipExrRtType) to specify the IP-address of the gateway on the network, where the… |
| 1.3.6.1.4.1.272.4.5.4.1.16 | ColumnipExtRtType | read-write | current | This object specifies, on point-to-multipoint interface whether the datagram shall be sent to the destination IP address in the IP datagram header (direct) or … |
| 1.3.6.1.4.1.272.4.5.4.1.17 | ColumnipExtRtMetric1 | read-write | current | This object is used to specify an order on the entries in the ipExtRtTable. If a datagram is matching multiple entries, the entry with the lowest value of ipEx… |
| 1.3.6.1.4.1.272.4.5.4.1.18 | ColumnipExtRtMetric2 | read-write | current | Undefined yet; for further extension |
| 1.3.6.1.4.1.272.4.5.4.1.19 | ColumnipExtRtMetric3 | read-write | current | Undefined yet; for further extension |
| 1.3.6.1.4.1.272.4.5.4.1.20 | ColumnipExtRtMetric4 | read-write | current | Undefined yet; for further extension |
| 1.3.6.1.4.1.272.4.5.4.1.21 | ColumnipExtRtMetric5 | read-write | current | Undefined yet; for further extension |
| 1.3.6.1.4.1.272.4.5.4.1.22 | ColumnipExtRtProto | read-write | current | This object describes, how the route has been gained. This will normaly be netmgmt, because there is currently no routing protocol, that is able to handle exte… |
| 1.3.6.1.4.1.272.4.5.4.1.23 | ColumnipExtRtAge | read-write | current | This object specifies the age of the route. |
| 1.3.6.1.4.1.272.4.5.4.1.24 | ColumnipExtRtDescription | read-write | mandatory | A textual string describing this extended route. |
| 1.3.6.1.4.1.272.4.5.5 | TableipNatTable | not-accessible | current | If NAT is switched on for an interface, this table contains an entry for each session running over the interface. Table entries are creates by the system whene… |
| 1.3.6.1.4.1.272.4.5.5.1 | RowipNatEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.5.1.1 | ColumnipNatIfIndex | read-only | current | This object specifies the interface, for which the session is monitored. |
| 1.3.6.1.4.1.272.4.5.5.1.2 | ColumnipNatProtocol | read-only | current | This object specifies the protocol, the session is using. The value icmp specifies an icmp-echo (ping) session. ICMP error messages are processed by the approp… |
| 1.3.6.1.4.1.272.4.5.5.1.3 | ColumnipNatIntAddr | read-only | current | This object specifies the internal local IP Address used for the session. The internal address is only visible to inside networks and is translated to the exte… |
| 1.3.6.1.4.1.272.4.5.5.1.4 | ColumnipNatIntPort | read-only | current | This object specifies the internal local portnumber used for the session. The internal portnumber is only visible to inside networks and is translated to the e… |
| 1.3.6.1.4.1.272.4.5.5.1.5 | ColumnipNatExtAddr | read-only | current | This object specifies the external local address used for the session. This address is visible outside only and will be translated to the internal address, whe… |
| 1.3.6.1.4.1.272.4.5.5.1.6 | ColumnipNatExtPort | read-only | current | This object specifies the external local portnumber used for the session. This address is visible outside only and is translated to the internal portnumber, wh… |
| 1.3.6.1.4.1.272.4.5.5.1.7 | ColumnipNatRemoteAddr | read-only | current | This object specifies the remote IP-address used for the session. This is an outside address. However, it is visible to outside networks and also to inside net… |
| 1.3.6.1.4.1.272.4.5.5.1.8 | ColumnipNatRemotePort | read-only | current | This object specifies the remote portnumber used for the session. This is an outside portnumber. However, it is visible to outside networks and also to inside … |
| 1.3.6.1.4.1.272.4.5.5.1.9 | ColumnipNatDirection | read-only | current | This object specifies, whether the session is incoming (from outside to inside) or outgoing (from inside to outside). |
| 1.3.6.1.4.1.272.4.5.5.1.10 | ColumnipNatAge | read-only | current | This object specifies how long no packet has been transferred for the session and is used internally for timeout purposes. |
| 1.3.6.1.4.1.272.4.5.5.1.11 | ColumnipNatContext | read-only | current | This object holds a protocol specific context needed to identify sessions for ICMP unreachable address mapping. |
| 1.3.6.1.4.1.272.4.5.5.1.12 | ColumnipNatTimeout | read-only | current | When there is no traffic associated with a NAT entry, this entry is discarded at the end of a timeout value. This object holds this timeout value in seconds. |
| 1.3.6.1.4.1.272.4.5.5.1.13 | ColumnipNatState | read-only | current | Set this object to delete to remove this entry. |
| 1.3.6.1.4.1.272.4.5.5.1.14 | ColumnipNatCategory | read-only | current | Specifies the NAT category according RFC 3489 and 5389 to be applied for UDP traffic matching with this entry. |
| 1.3.6.1.4.1.272.4.5.6 | TableipNatPresetTable | not-accessible | current | This table specifies the IP addresses and port numbers for sessions requested from outside. If this table is empty and NAT is enabled, only packets for session… |
| 1.3.6.1.4.1.272.4.5.6.1 | RowipNatPresetEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.6.1.1 | ColumnipNatPrIfIndex | read-write | current | This object specifies the interface index, for which the table entry shall be valid. If set to 0, the entry will be valid for all interfaces configured to use … |
| 1.3.6.1.4.1.272.4.5.6.1.2 | ColumnipNatPrProtocol | read-write | current | This object specifies the protocol, for which the table entry shall be valid. |
| 1.3.6.1.4.1.272.4.5.6.1.3 | ColumnipNatPrRemoteAddr | read-write | current | This object specifies together with ipNatPrRemoteMask the the set of IP addresses of remote hosts initiating a session. The table entry will be valid for an in… |
| 1.3.6.1.4.1.272.4.5.6.1.4 | ColumnipNatPrRemoteMask | read-write | current | This object specifies together with ipNatPrRemoteAddr the set of IP addresses of remote hosts initiating the session. The table entry will be valid for an inco… |
| 1.3.6.1.4.1.272.4.5.6.1.5 | ColumnipNatPrExtAddr | read-write | current | This object specifies together with ipNatPrExtMask the set of destination IP addresses, for which the table entry shall be valid. The entry is valid, if the ta… |
| 1.3.6.1.4.1.272.4.5.6.1.6 | ColumnipNatPrExtMask | read-write | current | This object specifies together with ipNatPrExtAddr the set of destination IP addresses, for which the table entry shall be valid. The entry is valid, if the ta… |
| 1.3.6.1.4.1.272.4.5.6.1.7 | ColumnipNatPrExtPort | read-write | current | This object specifies together with ipNatPrExtPortRange the range of port numbers for incoming packets, for which the table entry shall be valid. If both objec… |
| 1.3.6.1.4.1.272.4.5.6.1.8 | ColumnipNatPrExtPortRange | read-write | current | This object specifies together with ipNatPrExtPort the range of portnumbers for incoming packets, for which the table entry shall be valid. If both objects are… |
| 1.3.6.1.4.1.272.4.5.6.1.9 | ColumnipNatPrIntAddr | read-write | current | With ipNatPrIntMask, this object specifies the internal target host's IP address for incoming packets matching the table entry. An incoming packet matching thi… |
| 1.3.6.1.4.1.272.4.5.6.1.10 | ColumnipNatPrIntPort | read-write | current | This object specifies the internal target host's port-number for incoming packets matching the table entry. If this object is set to -1, the target portnumber … |
| 1.3.6.1.4.1.272.4.5.6.1.11 | ColumnipNatPrIntMask | read-write | current | With ipNatPrIntAddr, this object specifies the internal target host's IP address for incoming packets matching the table entry. An incoming packet matching thi… |
| 1.3.6.1.4.1.272.4.5.6.1.12 | ColumnipNatPrTimeout | read-write | current | When there is no traffic associated with a NAT entry, this entry is discarded at the end of a timeout value. This object holds this timeout value in seconds. I… |
| 1.3.6.1.4.1.272.4.5.6.1.13 | ColumnipNatPrDescr | read-write | current | A textual string describing this NAT forwarding rule. |
| 1.3.6.1.4.1.272.4.5.7 | TableipSessionTable | not-accessible | current | . |
| 1.3.6.1.4.1.272.4.5.7.1 | RowipSessionEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.7.1.1 | ColumnipSessionSrcAddr | read-only | current | source address of IP session |
| 1.3.6.1.4.1.272.4.5.7.1.2 | ColumnipSessionSrcPort | read-only | current | source port of IP session |
| 1.3.6.1.4.1.272.4.5.7.1.3 | ColumnipSessionDstAddr | read-only | current | destination port of IP session |
| 1.3.6.1.4.1.272.4.5.7.1.4 | ColumnipSessionDstPort | read-only | current | destination port of IP session |
| 1.3.6.1.4.1.272.4.5.7.1.5 | ColumnipSessionOutPkts | read-only | current | outgoing packets in IP session |
| 1.3.6.1.4.1.272.4.5.7.1.6 | ColumnipSessionOutOctets | read-only | current | outgoing octets in IP session |
| 1.3.6.1.4.1.272.4.5.7.1.7 | ColumnipSessionInPkts | read-only | current | incoming packets in IP session |
| 1.3.6.1.4.1.272.4.5.7.1.8 | ColumnipSessionInOctets | read-only | current | incoming octets in IP session |
| 1.3.6.1.4.1.272.4.5.7.1.9 | ColumnipSessionProtocol | read-only | current | protocol of IP session |
| 1.3.6.1.4.1.272.4.5.7.1.10 | ColumnipSessionAge | read-only | current | age of IP session |
| 1.3.6.1.4.1.272.4.5.7.1.11 | ColumnipSessionIdle | read-only | current | idle time of IP session |
| 1.3.6.1.4.1.272.4.5.7.1.12 | ColumnipSessionSrcIfIndex | read-only | current | source interface index of IP session |
| 1.3.6.1.4.1.272.4.5.7.1.13 | ColumnipSessionDstIfIndex | read-only | current | destination interface index of IP session |
| 1.3.6.1.4.1.272.4.5.12 | TableipImportTable | not-accessible | current | This table specifies how routes from one routing protocol are imported into another routing protocol. The dummy protocol default-route allows the generation of… |
| 1.3.6.1.4.1.272.4.5.12.1 | RowipImportEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.12.1.1 | ColumnipImportSrcProto | read-write | current | This object describes the protocol that generated the route and inserted it into the routing table. |
| 1.3.6.1.4.1.272.4.5.12.1.2 | ColumnipImportDstProto | read-write | current | This object describes the destination protocol into that the routes should be imported. |
| 1.3.6.1.4.1.272.4.5.12.1.3 | ColumnipImportMetric1 | read-write | current | This object defines the metric in the context of the destination protocol the imported routes should get. If set to -1 these routes get a protocol specific def… |
| 1.3.6.1.4.1.272.4.5.12.1.4 | ColumnipImportType | read-write | current | This object might define protocol specific properties of the imported routes in the context of the destination protocol. |
| 1.3.6.1.4.1.272.4.5.12.1.5 | ColumnipImportAddr | read-write | current | This object specifies together with ipImportMask the range of IP addresses for which the table entry should be valid. The entry is valid if the destination IP … |
| 1.3.6.1.4.1.272.4.5.12.1.6 | ColumnipImportMask | read-write | current | This object specifies together with ipImportAddr the range of IP addresses for which the table entry should be valid. The entry is valid if the destination IP … |
| 1.3.6.1.4.1.272.4.5.12.1.7 | ColumnipImportEffect | read-write | current | This object defines the effect this row should have. If set to import, the importation from ipImportSrcProto to ipImportDstProto takes place. If set to doNotIm… |
| 1.3.6.1.4.1.272.4.5.12.1.8 | ColumnipImportIfIndex | read-write | current | This object specifies the interface index of the interface for which the entry should be valid. If set to -1 it will be valid for all interfaces. |
| 1.3.6.1.4.1.272.4.5.12.1.9 | ColumnipImportAssociatedAS | read-write | current | This object specifies an optional Autonomous System identifier for use with BGP. |
| 1.3.6.1.4.1.272.4.5.12.1.10 | ColumnipImportRouteMapName | read-write | current | This object specifies an optional route-map name for use with BGP. |
| 1.3.6.1.4.1.272.4.5.13 | TableipPriorityTable | not-accessible | current | This table defines the order, in which routes from different protocols are being used to determine the destination of an ip packet. The table will contain an e… |
| 1.3.6.1.4.1.272.4.5.13.1 | RowipPriorityEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.13.1.1 | ColumnipPriorityProto | read-only | current | This object specifies the routig-protocol, for which the entry is valid. |
| 1.3.6.1.4.1.272.4.5.13.1.2 | ColumnipPriorityValue | read-write | current | This object contains the priority-value for a specific routing protocol. Low values mean high precedence. |
| 1.3.6.1.4.1.272.4.5.15 | TableipFilterTable | not-accessible | current | The ipFilterTable defines filters that describe subsets of IP packets. The filter matches if all conditions defined are true when comparing with the header of … |
| 1.3.6.1.4.1.272.4.5.15.1 | RowipFilterEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.15.1.1 | ColumnipFilterIndex | read-only | current | This object uniquely references this filter. The index value is generated automatically. |
| 1.3.6.1.4.1.272.4.5.15.1.2 | ColumnipFilterDescr | read-write | current | A textual string describing this filter. |
| 1.3.6.1.4.1.272.4.5.15.1.3 | ColumnipFilterProtocol | read-write | current | This object specifies the value of the protocol field in the ip header for all IP-datagrams belonging to the set. If this object is set to dont-verify, the val… |
| 1.3.6.1.4.1.272.4.5.15.1.4 | ColumnipFilterSrcAddr | read-write | current | This object specifies together with ipFilterSrcMask the set of IP addresses of datagrams that belong to the subset defined by this entry. If both objects are s… |
| 1.3.6.1.4.1.272.4.5.15.1.5 | ColumnipFilterSrcMask | read-write | current | This object specifies together with ipFilterSrcAddr the set of IP addresses of datagrams that belong to the subset defined by this entry. If both objects are s… |
| 1.3.6.1.4.1.272.4.5.15.1.6 | ColumnipFilterSrcPort | read-write | current | This object describes together with ipFilterSrcPortRange the range of source portnumbers of the IP-datagrams belonging to the set. All portnumbers between and … |
| 1.3.6.1.4.1.272.4.5.15.1.7 | ColumnipFilterSrcPortRange | read-write | current | This object describes together with ipFilterDstPort the range of source portnumbers of the IP-datagrams belonging to the set. All portnumbers between and inclu… |
| 1.3.6.1.4.1.272.4.5.15.1.8 | ColumnipFilterDstAddr | read-write | current | This object describes together with ipFilterDstMask the range of the target-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.… |
| 1.3.6.1.4.1.272.4.5.15.1.9 | ColumnipFilterDstMask | read-write | current | This object describes together with ipFilterDstAddr the range of the target-addresses of the IP-datagrams belonging to the set. If both objects are set to 0.0.… |
| 1.3.6.1.4.1.272.4.5.15.1.10 | ColumnipFilterDstPort | read-write | current | This object describes together with ipFilterDstPortRange the range of target-portnumbers of the IP-datagrams belonging to the set. All portnumbers between and … |
| 1.3.6.1.4.1.272.4.5.15.1.11 | ColumnipFilterDstPortRange | read-write | current | This object describes together with ipFilterDstPort the range of target-portnumbers of the IP-datagrams belonging to the set. All portnumbers between and inclu… |
| 1.3.6.1.4.1.272.4.5.15.1.12 | ColumnipFilterTcpConnState | read-write | current | This object describes the state of the TCP connection associated with the packets belonging to the set. If this object is set to established, the value of the … |
| 1.3.6.1.4.1.272.4.5.15.1.13 | ColumnipFilterIcmpType | read-write | current | This object describes the ICMP type of the packets belonging to the set. If this object is set to dont-verify, the value of the ICMP type field is not specifie… |
| 1.3.6.1.4.1.272.4.5.15.1.14 | ColumnipFilterTos | read-write | current | This object describes together with ipFilterTosMask the range of the Type of Service field (TOS) in the IP-header of the IP-datagrams belonging to the set. A T… |
| 1.3.6.1.4.1.272.4.5.15.1.15 | ColumnipFilterTosMask | read-write | current | This object describes together with ipFilterTos the range of the Type of Service field (TOS) in the IP-header of the IP-datagrams belonging to the set. A TOS v… |
| 1.3.6.1.4.1.272.4.5.15.1.16 | ColumnipFilterLevel2Prio | read-write | current | This object describes together with ipFilterLevel2PrioMask the range of the level 2 priority field associated with the IP-datagrams belonging to the set. A pri… |
| 1.3.6.1.4.1.272.4.5.15.1.17 | ColumnipFilterLevel2PrioMask | read-write | current | This object describes together with ipFilterLevel2PrioMask the range of the level 2 priority field associated with the IP-datagrams belonging to the set. A pri… |
| 1.3.6.1.4.1.272.4.5.15.1.18 | ColumnipFilterSrcIfIndex | read-write | current | This object specifies the source index of the IP-datagrams. If this object has a value other than 0, only datagrams received over the interface with the approp… |
| 1.3.6.1.4.1.272.4.5.16 | TableipRuleTable | not-accessible | current | The ipRuleTable defines access rules for checking incoming IP packets. The rules are processed in order, i.e. each rule has a link to the next rule. The set of… |
| 1.3.6.1.4.1.272.4.5.16.1 | RowipRuleEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.16.1.1 | ColumnipRuleIndex | read-only | current | Unique rule index. |
| 1.3.6.1.4.1.272.4.5.16.1.2 | ColumnipRuleFilterIndex | read-write | current | References the rule's associated filter. |
| 1.3.6.1.4.1.272.4.5.16.1.3 | ColumnipRuleAction | read-write | current | This object specifies the action to be performed if the rule's associated filter matches. If set to ignore the filter is not consulted and the next rule is pro… |
| 1.3.6.1.4.1.272.4.5.16.1.4 | ColumnipRuleNextRuleIndex | read-write | current | Specifies the next rule to be processed if the rule's associated filter does not match. The value 0 is used to mark the end of the rule set. |
| 1.3.6.1.4.1.272.4.5.16.1.5 | ColumnipRuleDescr | read-write | current | A textual string describing this access rule. |
| 1.3.6.1.4.1.272.4.5.18 | TableipNatOutTable | not-accessible | current | This table specifies the IP address translation for outgoing sessions. If no matching entry is found the IP address is set to the IP address defined on the int… |
| 1.3.6.1.4.1.272.4.5.18.1 | RowipNatOutEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.18.1.1 | ColumnipNatOutIfIndex | read-write | current | This object specifies the interface index, for which the table entry shall be valid. If set to 0, the entry will be valid for all interfaces configured to use … |
| 1.3.6.1.4.1.272.4.5.18.1.2 | ColumnipNatOutProtocol | read-write | current | This object specifies the protocol, for which the table entry shall be valid. |
| 1.3.6.1.4.1.272.4.5.18.1.3 | ColumnipNatOutRemoteAddr | read-write | current | This object specifies together with ipNatOutRemoteMask the set of target IP addresses for which the table entry is valid. If both objects are set to 0.0.0.0, t… |
| 1.3.6.1.4.1.272.4.5.18.1.4 | ColumnipNatOutRemoteMask | read-write | current | This object specifies together with ipNatOutRemoteAddr the set of target IP addresses for which the table entry is valid. If both objects are set to 0.0.0.0, t… |
| 1.3.6.1.4.1.272.4.5.18.1.5 | ColumnipNatOutExtAddr | read-write | current | With ipNatOutExtMask, this object specifies the external 'IP address' or 'NET address' to which the internal IP address is mapped. - To map exactly to ipNatOut… |
| 1.3.6.1.4.1.272.4.5.18.1.6 | ColumnipNatOutRemotePort | read-write | current | This object specifies together with ipNatOutRemotePortRange the range of portnumbers for outgoing packets, for which the table entry shall be valid. If both ob… |
| 1.3.6.1.4.1.272.4.5.18.1.7 | ColumnipNatOutRemotePortRange | read-write | current | This object specifies together with ipNatOutRemotePort the range of portnumbers for outgoing packets, for which the table entry shall be valid. If both objects… |
| 1.3.6.1.4.1.272.4.5.18.1.8 | ColumnipNatOutIntAddr | read-write | current | This object specifies together with ipNatOutIntMask the internal hosts IP address for outgoing packets matching the table entry. If both objects are set to 0.0… |
| 1.3.6.1.4.1.272.4.5.18.1.9 | ColumnipNatOutIntMask | read-write | current | This object specifies together with ipNatOutIntAddr the internal hosts IP address for outgoing packets matching the table entry. If both objects are set to 0.0… |
| 1.3.6.1.4.1.272.4.5.18.1.10 | ColumnipNatOutIntPort | read-write | current | This object specifies the internal source port for which the table entry shall be valid. If this object is set to -1, any internal source port matches this ent… |
| 1.3.6.1.4.1.272.4.5.18.1.11 | ColumnipNatOutExtPort | read-write | current | This object may be used to specify a fixed external source port to which the internal source port is mapped. If this object is set to -1, the port is mapped to… |
| 1.3.6.1.4.1.272.4.5.18.1.12 | ColumnipNatOutExtMask | read-write | current | With ipNatOutExtAddr, this object specifies the external 'IP address' or 'NET address' to which the internal IP address is mapped. - To map exactly to ipNatOut… |
| 1.3.6.1.4.1.272.4.5.18.1.13 | ColumnipNatOutTimeout | read-write | current | When there is no traffic associated with a NAT entry, this entry is discarded at the end of a timeout value. This object holds this timeout value in seconds. I… |
| 1.3.6.1.4.1.272.4.5.18.1.14 | ColumnipNatOutDescr | read-write | current | A textual string describing this NAT translation rule. |
| 1.3.6.1.4.1.272.4.5.18.1.15 | ColumnipNatOutNatCategory | read-write | current | Specifies the NAT category according RFC 3489 and 5389 to be applied for UDP traffic matching with this entry. |
| 1.3.6.1.4.1.272.4.5.18.1.16 | ColumnipNatOutIntPortRange | read-write | current | This object specifies together with ipNatOutIntPort the internal source port range for which the table entry shall be valid. If this object is set to -1, only … |
| 1.3.6.1.4.1.272.4.5.18.1.17 | ColumnipNatOutExtPortRange | read-write | current | This object may be used together with ipNatOutExtPort to specify a fixed external source port number range to which the internal source port numbers are mapped… |
| 1.3.6.1.4.1.272.4.5.19 | TableipHostsAliveTable | not-accessible | current | This table specifies the watched IP addresses. Entries in the table are created and removed manually by network management. |
| 1.3.6.1.4.1.272.4.5.19.1 | RowipHostsAliveEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.19.1.1 | ColumnipHostsAliveGroup | read-write | current | The group of the watched IP-Addresses |
| 1.3.6.1.4.1.272.4.5.19.1.2 | ColumnipHostsAliveIPAddress | read-write | current | The watched IP-Address. If set to zero, the default gateway is used. |
| 1.3.6.1.4.1.272.4.5.19.1.3 | ColumnipHostsAliveState | read-only | current | The State of the watched IP-Address |
| 1.3.6.1.4.1.272.4.5.19.1.4 | ColumnipHostsAliveInterval | read-write | current | This is the time interval for state verification |
| 1.3.6.1.4.1.272.4.5.19.1.5 | ColumnipHostsAliveDownAction | read-write | current | Action be performed if the ipHostsAliveState changes to down (2), If set to none (4) there is no action specified, if set to monitor (7) this entry just enable… |
| 1.3.6.1.4.1.272.4.5.19.1.6 | ColumnipHostsAliveFirstIfIndex | read-write | current | The first ifc |
| 1.3.6.1.4.1.272.4.5.19.1.7 | ColumnipHostsAliveRange | read-write | current | The range of all ifc's |
| 1.3.6.1.4.1.272.4.5.19.1.8 | ColumnipHostsAliveSrcIPAddress | read-write | current | The source IP-Address |
| 1.3.6.1.4.1.272.4.5.19.1.9 | ColumnipHostsAliveTrials | read-write | current | How many ping attempts until host is considered down. Default value is 3. |
| 1.3.6.1.4.1.272.4.5.19.1.10 | ColumnipHostsAliveBackups | read-write | current | How many successful pings until host is considered up. Default value is 1. |
| 1.3.6.1.4.1.272.4.5.21 | TableipBodRuleTable | not-accessible | current | The ipBodRuleTable defines access rules for checking incoming IP packets. The rules are processed in order, i.e. each rule has a link to the next rule. The set… |
| 1.3.6.1.4.1.272.4.5.21.1 | RowipBodRuleEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.21.1.1 | ColumnipBodRuleIndex | read-only | current | Unique rule index. |
| 1.3.6.1.4.1.272.4.5.21.1.2 | ColumnipBodRuleFilterIndex | read-only | current | References the rule's associated filter. |
| 1.3.6.1.4.1.272.4.5.21.1.3 | ColumnipBodRuleAction | read-write | current | This object specifies the action to be performed if the rule's associated filter matches. If set to ignore the filter is not consulted and the next rule is pro… |
| 1.3.6.1.4.1.272.4.5.21.1.4 | ColumnipBodRuleDirection | read-write | current | This object specifies the direction of the packets for which the rule is processed. |
| 1.3.6.1.4.1.272.4.5.21.1.5 | ColumnipBodRuleChannels | read-write | current | The number of B-channels to invoke if the rule's associated filter matches. |
| 1.3.6.1.4.1.272.4.5.21.1.6 | ColumnipBodRuleNextRuleIndex | read-write | current | Specifies the next rule to be processed if the rule's associated filter does not match. The value 0 is used to mark the end of the rule set. |
| 1.3.6.1.4.1.272.4.5.21.1.7 | ColumnipBodRuleIdleTime | read-write | current | Specifies the time in seconds the interface-specific shorthold interval (see biboPPPTable) is extended if the rule's associated filter matches. When set to zer… |
| 1.3.6.1.4.1.272.4.5.22 | TableipQoSTable | not-accessible | current | The ipQosTable defines the classifier rules that are applied to IP traffic arriving this interface in a particular direction. The rules are processed in order,… |
| 1.3.6.1.4.1.272.4.5.22.1 | RowipQoSEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.22.1.1 | ColumnipQoSIndex | read-only | current | Unique rule index. |
| 1.3.6.1.4.1.272.4.5.22.1.2 | ColumnipQoSFilterIndex | read-write | current | References the associated filter (see IpFilterTable). |
| 1.3.6.1.4.1.272.4.5.22.1.3 | ColumnipQoSNextRuleIndex | read-write | current | Specifies the next classifier rule to be processed if the rule's associated filter does not match. The value 0 is used to mark the end of the rule set. |
| 1.3.6.1.4.1.272.4.5.22.1.4 | ColumnipQoSAction | read-write | obsolete | WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: This ob… |
| 1.3.6.1.4.1.272.4.5.22.1.5 | ColumnipQoSTos | read-write | obsolete | WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: Value f… |
| 1.3.6.1.4.1.272.4.5.22.1.7 | ColumnipQoSTosSetRate | read-write | obsolete | WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: Maximum… |
| 1.3.6.1.4.1.272.4.5.22.1.8 | ColumnipQoSTosSetBurst | read-write | obsolete | WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: Maximum… |
| 1.3.6.1.4.1.272.4.5.22.1.9 | ColumnipQoSTosSetExceedAction | read-write | obsolete | WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: This ob… |
| 1.3.6.1.4.1.272.4.5.22.1.10 | ColumnipQoSTosRemark | read-write | obsolete | WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: Value f… |
| 1.3.6.1.4.1.272.4.5.22.1.11 | ColumnipQoSServiceClass | read-write | current | This object specifies together with ipQoSClassId the class of service used for the congestion management, priorization and traffic shapping. If set to high-pri… |
| 1.3.6.1.4.1.272.4.5.22.1.12 | ColumnipQoSClassId | read-write | current | This object specifies together with ipQoSServiceClass (normal(1) only) the class of service used for congestion avoidance, congestion management, priorization … |
| 1.3.6.1.4.1.272.4.5.22.1.13 | ColumnipQoSDirection | read-write | current | This object specifies the direction for witch this classifier rule applies on this interface, possible values: outgoing(1) = used for outgoing packets only inc… |
| 1.3.6.1.4.1.272.4.5.22.1.14 | ColumnipQoSTosSetRateLimitation | read-write | obsolete | WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: This fi… |
| 1.3.6.1.4.1.272.4.5.22.1.15 | ColumnipQoSTosSetRateBps | read-write | obsolete | WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: Maximum… |
| 1.3.6.1.4.1.272.4.5.22.1.16 | ColumnipQoSTosSetBurstBps | read-write | obsolete | WARNING: this object is obsolete and must not be used. It exists in this table for configuration conversion purposes. Below is its previous definition: Maximum… |
| 1.3.6.1.4.1.272.4.5.22.1.17 | ColumnipQoSClassifyAction | read-write | current | This object specifies the action to be performed if the associated filter matches. If set to disabled the filter is not consulted and the next rule is processe… |
| 1.3.6.1.4.1.272.4.5.22.1.18 | ColumnipQoSExceedRateLimitation | read-write | current | This field specifies a rate limitation between in-profile and out-profile datagrams. Possible values: none(1) = no limitation is defined. packets(2) = a limita… |
| 1.3.6.1.4.1.272.4.5.22.1.19 | ColumnipQoSExceedRate | read-write | current | Maximum amount of packets per second that are considered in-profile. Packets in excess of (ipQosExceedRate + ipQosExceedBurst) are considered out-profile. |
| 1.3.6.1.4.1.272.4.5.22.1.20 | ColumnipQoSExceedBurst | read-write | current | Maximum additional amount of packets per second that are considered in-profile. Packets in excess of (ipQosExceedRate + ipQosExceedBurst) are considered out-pr… |
| 1.3.6.1.4.1.272.4.5.22.1.21 | ColumnipQoSExceedRateBps | read-write | current | Maximum amount of traffic in bits per second that is considered in-profile. Traffic in excess of (ipQosExceedRateBps + ipQosExceedBurstBps) is considered out-p… |
| 1.3.6.1.4.1.272.4.5.22.1.22 | ColumnipQoSExceedBurstBps | read-write | current | Maximum amount of additional traffic that is considered in-profile. Traffic in excess of (ipQosExceedRateBps + ipQosExceedBurstBps) is considered out-profile. |
| 1.3.6.1.4.1.272.4.5.22.1.23 | ColumnipQoSTosAndMask | read-write | current | AND mask applied to TOS field inside IP header of in-profile datagrams. |
| 1.3.6.1.4.1.272.4.5.22.1.24 | ColumnipQoSTosOrMask | read-write | current | OR mask applied to TOS field inside IP header of in-profile datagrams. |
| 1.3.6.1.4.1.272.4.5.22.1.25 | ColumnipQoSLevel2PrioAndMask | read-write | current | AND mask applied to level 2 priority associated with in-profile datagrams. |
| 1.3.6.1.4.1.272.4.5.22.1.26 | ColumnipQoSLevel2PrioOrMask | read-write | current | OR mask applied to level 2 priority associated with in-profile datagrams. |
| 1.3.6.1.4.1.272.4.5.22.1.27 | ColumnipQoSTosAndMaskExceed | read-write | current | AND mask applied to TOS field inside IP header of out-profile datagrams. |
| 1.3.6.1.4.1.272.4.5.22.1.28 | ColumnipQoSTosOrMaskExceed | read-write | current | OR mask applied to TOS field inside IP header of out-profile datagrams. |
| 1.3.6.1.4.1.272.4.5.22.1.29 | ColumnipQoSLevel2PrioAndMaskExceed | read-write | current | AND mask applied to level 2 priority associated with out-profile datagrams. |
| 1.3.6.1.4.1.272.4.5.22.1.30 | ColumnipQoSLevel2PrioOrMaskExceed | read-write | current | OR mask applied to level 2 priority associated with out-profile datagrams. |
| 1.3.6.1.4.1.272.4.5.22.1.31 | ColumnipQoSDescr | read-write | current | A textual string describing this classifier rules. |
| 1.3.6.1.4.1.272.4.5.23 | TableipRipTimerTable | not-accessible | current | The 'ipRipTimerTable' contains the basic configuration of the RIP protocol. Formerly created to define only the 3 timers involved in RIP process (cf RFC 2453).… |
| 1.3.6.1.4.1.272.4.5.23.1 | RowipRipTimerEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.23.1.1 | ColumnipRipVersion | read-only | current | RFC 2453, RIP Version 2. |
| 1.3.6.1.4.1.272.4.5.23.1.2 | ColumnipRipTimerUpdate | read-write | current | An unsollicited RIP response is broadcast every 'ipRipTimerUpdate' seconds. |
| 1.3.6.1.4.1.272.4.5.23.1.3 | ColumnipRipTimerTimeout | read-write | current | If 'ipRipTimerTimeout' seconds elapse from the last time an update message is received for this route, the route is dropped but keeped in routing table. Then '… |
| 1.3.6.1.4.1.272.4.5.23.1.4 | ColumnipRipTimerGarbage | read-write | current | If 'ipRipTimerGarbage' seconds elapse from the start of 'garbage process' (and if route is still 'dropped'), the route is removed from the routing table. |
| 1.3.6.1.4.1.272.4.5.23.1.5 | ColumnipRipRfc2453Timer | read-write | current | The 'ipRipRfc2453Timer' enabled/disables variable timer definition from RFC 2453. |
| 1.3.6.1.4.1.272.4.5.23.1.6 | ColumnipRipRfc2091Timer | read-write | current | The 'ipRipRfc2453Timer' enabled/disables variable timer definition from RFC 2091. |
| 1.3.6.1.4.1.272.4.5.23.1.7 | ColumnipRipUpdatePacketRetryTimer | read-write | current | If 'ipRipTimerUpdatePacketRetry' seconds elapse since the transmission of the last update packet without receiving an acknowledge the update packet is resend. |
| 1.3.6.1.4.1.272.4.5.23.1.8 | ColumnipRipPoisonedReverse | read-write | current | Enable or disable the (currently unimplemented) control over 'poisoned reverse' route distribution. |
| 1.3.6.1.4.1.272.4.5.23.1.9 | ColumnipRipDistributeDefaultRoutes | read-write | current | Enable or disable the distribution of 'default routes'. |
| 1.3.6.1.4.1.272.4.5.23.1.10 | ColumnipRipHoldDownTimer | read-write | current | If 'ipRipHoldDownTimer' seconds elapse from the start of 'database timeout' (and if route is still 'dropped'), the route is removed from the routing table. |
| 1.3.6.1.4.1.272.4.5.32 | NodeipIcmp | |||
| 1.3.6.1.4.1.272.4.5.32.1 | ScalaripIcmpSourceQuench | read-write | current | enabled : If an IP packet is discarded due to congestion, the system sends an ICMP 'Source-Quench' message back to the originator of the packet. For congestion… |
| 1.3.6.1.4.1.272.4.5.32.2 | ScalaripIcmpTimeExceededTrans | read-write | current | enabled : If an IP packet could not be delivered/forwarded to destination due to packet TTL (Time to live) or dialup-interface timeout, the packet is discarded… |
| 1.3.6.1.4.1.272.4.5.32.3 | ScalaripIcmpTimeExceededFrag | read-write | current | enabled : If an IP packet could not be delivered/forwarded to destination due to fragment-reassembly timeout, the system sends an ICMP 'Time-Exceeded/Fragment'… |
| 1.3.6.1.4.1.272.4.5.32.4 | ScalaripIcmpDestUnreachFrag | read-write | current | enabled : If an IP packet could not be delivered/forwarded to destination due to MTU/Dont-Fragment error (packet must be fragmented due to interface-MTU but Do… |
| 1.3.6.1.4.1.272.4.5.32.5 | ScalaripIcmpDestUnreachHost | read-write | current | enabled : If an IP packet could not be delivered/forwarded to destination due to routing errors (e.g. no matching route exists, interface down/blocked), the pa… |
| 1.3.6.1.4.1.272.4.5.32.6 | ScalaripIcmpDestUnreachHostTcp | read-write | current | Set ICMP (Dest Unreachable/Host) behavior for TCP packets. tcp-rst : If a TCP packet can not be delivered/forwarded to destination (e.g. no matching route exis… |
| 1.3.6.1.4.1.272.4.5.32.7 | ScalaripIcmpDestUnreachProto | read-write | current | enabled: If an IP packet addressed to local system could not be handled due to unsupported protocol type in IP packet-header (e.g. not TCP, UDP or ICMP), the p… |
| 1.3.6.1.4.1.272.4.5.32.8 | ScalaripIcmpEchoReply | read-write | current | enabled : each incoming ICMP 'Echo-Request' message addressed to local system is answered with an ICMP 'Echo-Reply' message. This is the default behavior of th… |
| 1.3.6.1.4.1.272.4.5.32.9 | ScalaripIcmpMaskReply | read-write | current | enabled : each incoming ICMP 'Mask-Request' message addressed to local system is answered with an ICMP 'Mask-Reply' message. This is the default behavior of th… |
| 1.3.6.1.4.1.272.4.5.32.10 | ScalaripIcmpTimestampReply | read-write | current | enabled : each incoming ICMP 'Timestamp' message addressed to local system is answered with an RFC792-compliant ICMP 'Timestamp-Reply' message. This is the def… |
| 1.3.6.1.4.1.272.4.5.33 | TableipRipFilterTable | not-accessible | current | The ipRipFilterTable contains additional information related to IP and the interfaces found on the system. Entries can only be added or deleted by the system. |
| 1.3.6.1.4.1.272.4.5.33.1 | RowipRipFilterEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.33.1.1 | ColumnipRipFilterEntryState | read-write | current | makes entry active |
| 1.3.6.1.4.1.272.4.5.33.1.2 | ColumnipRipFilterIfIndex | read-write | current | The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particu… |
| 1.3.6.1.4.1.272.4.5.33.1.3 | ColumnipRipFilterIpAddr | read-write | current | The IP-Address range affected by the filter operation. Ranges are separately defined for import and export. IP-Address ranges which are not matched by any filt… |
| 1.3.6.1.4.1.272.4.5.33.1.4 | ColumnipRipFilterNetMask | read-write | current | Indicate the mask to be logical-ANDed with the ip-address before being compared to the value in the ipRipFilterIpAddr field. If a subnet mask is not specified,… |
| 1.3.6.1.4.1.272.4.5.33.1.5 | ColumnipRipFilterPriority | read-write | current | If more than one filter matches the IP-Address range this priority decides which filter to apply. 1 indictes highest priority and 16 lowest priority |
| 1.3.6.1.4.1.272.4.5.33.1.6 | ColumnipRipFilterDirection | read-write | current | The direction the filter is defined for. |
| 1.3.6.1.4.1.272.4.5.33.1.7 | ColumnipRipFilterDistribution | read-write | current | Include or exclude the IP-Address range from distribution. |
| 1.3.6.1.4.1.272.4.5.33.1.8 | ColumnipRipFilterMetric1IfUpOffset | read-write | current | Add 'ipRipFilterMetric1IfUpOffset' to metric1 during import of this route if the operation status of this interface is up. On export, add 'ipRipFilterMetric1If… |
| 1.3.6.1.4.1.272.4.5.33.1.9 | ColumnipRipFilterMetric1IfDormantOffset | read-write | current | Add 'ipRipFilterMetric1IfDormantOffset' to metric1 during import of this route if the operation status of this interface is dormant. On export, add 'ipRipFilte… |
| 1.3.6.1.4.1.272.4.5.34 | TableipNatExpTable | not-accessible | current | If NAT is switched on for an interface, this table contains entries for expected sessions. Table entries are creates by the system whenever there is a need for… |
| 1.3.6.1.4.1.272.4.5.34.1 | RowipNatExpEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.34.1.1 | ColumnipNatExpIfIndex | read-only | current | This object specifies the interface, for which the session is expected. A value of 0 means ANY interface. |
| 1.3.6.1.4.1.272.4.5.34.1.2 | ColumnipNatExpProtocol | read-only | current | This object specifies the protocol, the expected session is using. |
| 1.3.6.1.4.1.272.4.5.34.1.3 | ColumnipNatExpIntAddr | read-only | current | This object specifies the internal local IP Address used for the expected session. |
| 1.3.6.1.4.1.272.4.5.34.1.4 | ColumnipNatExpIntPort | read-only | current | This object specifies the internal local port-number used for the expected session. A value of -1 means to copy the related external port-number without any NA… |
| 1.3.6.1.4.1.272.4.5.34.1.5 | ColumnipNatExpExtAddr | read-only | current | This object specifies the external local address used for the expected session. A value of 0.0.0.0 means ANY address. |
| 1.3.6.1.4.1.272.4.5.34.1.6 | ColumnipNatExpExtPort | read-only | current | This object specifies the external local port-number used for the expected session. A value of -1 means ANY port-number. |
| 1.3.6.1.4.1.272.4.5.34.1.7 | ColumnipNatExpRemoteAddr | read-only | current | This object specifies the remote IP-address used for the expected session. A value of 0.0.0.0 means ANY address. |
| 1.3.6.1.4.1.272.4.5.34.1.8 | ColumnipNatExpExtPortType | read-only | current | This field is used for NAT-internal signalling. Applications shall set it to <supplied>. For automatically generated, NAT-out-triggered entries, the system set… |
| 1.3.6.1.4.1.272.4.5.34.1.9 | ColumnipNatExpRemotePort | read-only | current | This object specifies the remote port-number used for the expected session. A value of -1 means ANY port number. |
| 1.3.6.1.4.1.272.4.5.34.1.10 | ColumnipNatExpTimeout | read-only | current | Set a specific Timeout in seconds for a new expected session. A value of 0 means UNSPECIFIED (default-value is taken). |
| 1.3.6.1.4.1.272.4.5.53 | TablemcastFwdTable | not-accessible | current | Entries in the Multicast Forwarding Table define a rule where to forward packets with a specified multicast group address to a dedicated destination interface. |
| 1.3.6.1.4.1.272.4.5.53.1 | RowmcastFwdEntry | not-accessible | current | An entry in the Multicast Forwarding Table. |
| 1.3.6.1.4.1.272.4.5.53.1.1 | ColumnmcastFwdAddress | read-write | current | The multicast forwarding group address which will be forwarded. The group address 224.0.0.0 may be used as a wildcard matching all addresses. |
| 1.3.6.1.4.1.272.4.5.53.1.2 | ColumnmcastFwdSrcIfIndex | read-write | current | The source interface of incoming multicast packets. |
| 1.3.6.1.4.1.272.4.5.53.1.3 | ColumnmcastFwdDestIfIndex | read-write | current | The destination interface where to forward multicast packets. |
| 1.3.6.1.4.1.272.4.5.53.1.4 | ColumnmcastFwdStatus | read-write | current | The status of this entry. |
| 1.3.6.1.4.1.272.4.5.57 | TableipLfiTable | not-accessible | current | . |
| 1.3.6.1.4.1.272.4.5.57.1 | RowipLfiEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.57.1.1 | ColumnipLfiIfIndex | read-write | current | This object specifies the associated interface. |
| 1.3.6.1.4.1.272.4.5.57.1.2 | ColumnipLfiMode | read-write | current | This object enables Link Framentation and Interleave (LFI) mode on the associated interface. |
| 1.3.6.1.4.1.272.4.5.57.1.10 | ColumnipLfiMaxFragSize | read-write | current | This object specifies the current maximum fragment size used for Link Fragmentation and Interleave (LFI) mode on the associated interface. |
| 1.3.6.1.4.1.272.4.5.57.1.11 | ColumnipLfiMinFragSize | read-write | current | This object specifies the current minimum fragment size used for Link Fragmentation and Interleave (LFI) mode on the associated interface. |
| 1.3.6.1.4.1.272.4.5.57.1.12 | ColumnipLfiCurrVoipCalls | read-write | current | The current number of VoIP Calls routed via the associated interface. |
| 1.3.6.1.4.1.272.4.5.60 | TableipNatExcludeTable | not-accessible | current | This table specifies the IP addresses and port numbers for sessions that must not be processed by NAT. Entries in the table are created and removed manually by… |
| 1.3.6.1.4.1.272.4.5.60.1 | RowipNatExcludeEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.60.1.1 | ColumnipNatExIfIndex | read-write | current | This object specifies the interface index, for which the table entry shall be valid. If set to 0, the entry will be valid for all interfaces configured to use … |
| 1.3.6.1.4.1.272.4.5.60.1.2 | ColumnipNatExProtocol | read-write | current | This object specifies the protocol, for which the table entry shall be valid. |
| 1.3.6.1.4.1.272.4.5.60.1.3 | ColumnipNatExLocalAddr | read-write | current | This object specifies together with ipNatExLocalMask the set of IP addresses of local hosts involved in the communication. The table entry will be valid when t… |
| 1.3.6.1.4.1.272.4.5.60.1.4 | ColumnipNatExLocalMask | read-write | current | This object specifies together with ipNatExLocalAddr the set of IP addresses of local hosts involved in the communication. The table entry will be valid when t… |
| 1.3.6.1.4.1.272.4.5.60.1.5 | ColumnipNatExLocalPort | read-write | current | This object specifies together with ipNatExLocalPortRange the range of local portnumbers, for which the table entry shall be valid. If both objects are set to … |
| 1.3.6.1.4.1.272.4.5.60.1.6 | ColumnipNatExLocalPortRange | read-write | current | This object specifies together with ipNatExLocalPort the range of local portnumbers, for which the table entry shall be valid. If both objects are set to -1, t… |
| 1.3.6.1.4.1.272.4.5.60.1.7 | ColumnipNatExRemoteAddr | read-write | current | This object specifies together with ipNatExRemoteMask the set of IP addresses of remote hosts involved in the communication. The table entry will be valid when… |
| 1.3.6.1.4.1.272.4.5.60.1.8 | ColumnipNatExRemoteMask | read-write | current | This object specifies together with ipNatExRemoteAddr the set of IP addresses of remote hosts involved in the communication. The table entry will be valid when… |
| 1.3.6.1.4.1.272.4.5.60.1.9 | ColumnipNatExRemotePort | read-write | current | This object specifies together with ipNatExRemotePortRange the range of remote portnumbers, for which the table entry shall be valid. If both objects are set t… |
| 1.3.6.1.4.1.272.4.5.60.1.10 | ColumnipNatExRemotePortRange | read-write | current | This object specifies together with ipNatExRemotePort the range of remote portnumbers, for which the table entry shall be valid. If both objects are set to -1,… |
| 1.3.6.1.4.1.272.4.5.60.1.11 | ColumnipNatExDescr | read-write | current | A textual string describing this NAT excluding rule. |
| 1.3.6.1.4.1.272.4.5.60.1.12 | ColumnipNatExAction | read-write | current | This object specifies which packets will be excluded from NAT processing. When set to 'exclude' (default value), any packet matching the parameters of the entr… |
| 1.3.6.1.4.1.272.4.5.61 | TableipNatOutOperTable | not-accessible | current | This table displays all currently active IP address translation policies in 'outgoing' direction. It's similar to the former defined ipNatOutTable. Table entri… |
| 1.3.6.1.4.1.272.4.5.61.1 | RowipNatOutOperEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.61.1.1 | ColumnipNatOutOperIfIndex | read-only | current | This object specifies the interface index, for which the table entry shall be valid. If set to 0, the entry will be valid for all interfaces configured to use … |
| 1.3.6.1.4.1.272.4.5.61.1.2 | ColumnipNatOutOperProtocol | read-only | current | This object specifies the protocol, for which the table entry shall be valid. |
| 1.3.6.1.4.1.272.4.5.61.1.3 | ColumnipNatOutOperRemoteAddr | read-only | current | This object specifies together with ipNatOutOperRemoteMask the set of target IP addresses for which the table entry is valid. If both objects are set to 0.0.0.… |
| 1.3.6.1.4.1.272.4.5.61.1.4 | ColumnipNatOutOperRemoteMask | read-only | current | This object specifies together with ipNatOutOperRemoteAddr the set of target IP addresses for which the table entry is valid. If both objects are set to 0.0.0.… |
| 1.3.6.1.4.1.272.4.5.61.1.5 | ColumnipNatOutOperExtAddr | read-only | current | With ipNatOutOperExtMask, this object specifies the external 'IP address' or 'NET address' to which the internal IP address is mapped. - To map exactly to ipNa… |
| 1.3.6.1.4.1.272.4.5.61.1.6 | ColumnipNatOutOperRemotePort | read-only | current | This object specifies together with ipNatOutRemotePortRange the range of portnumbers for outgoing packets, for which the table entry shall be valid. If both ob… |
| 1.3.6.1.4.1.272.4.5.61.1.7 | ColumnipNatOutOperRemotePortRange | read-only | current | This object specifies together with ipNatOutOperRemotePort the range of portnumbers for outgoing packets, for which the table entry shall be valid. If both obj… |
| 1.3.6.1.4.1.272.4.5.61.1.8 | ColumnipNatOutOperIntAddr | read-only | current | This object specifies together with ipNatOutOperIntMask the internal hosts IP address for outgoing packets matching the table entry. If both objects are set to… |
| 1.3.6.1.4.1.272.4.5.61.1.9 | ColumnipNatOutOperIntMask | read-only | current | This object specifies together with ipNatOutOperIntAddr the internal hosts IP address for outgoing packets matching the table entry. If both objects are set to… |
| 1.3.6.1.4.1.272.4.5.61.1.10 | ColumnipNatOutOperIntPort | read-only | current | This object specifies the internal source port for which the table entry shall be valid. If this object is set to -1, any internal source port matches this ent… |
| 1.3.6.1.4.1.272.4.5.61.1.11 | ColumnipNatOutOperExtPort | read-only | current | This object may be used to specify a fixed external source port to which the internal source port is mapped. If this object is set to -1, the port is mapped to… |
| 1.3.6.1.4.1.272.4.5.61.1.12 | ColumnipNatOutOperExtMask | read-only | current | With ipNatOutOperExtAddr, this object specifies the external 'IP address' or 'NET address' to which the internal IP address is mapped. - To map exactly to ipNa… |
| 1.3.6.1.4.1.272.4.5.61.1.13 | ColumnipNatOutOperTimeout | read-only | current | When there is no traffic associated with a NAT entry, this entry is discarded at the end of a timeout value. This object holds this timeout value in seconds. I… |
| 1.3.6.1.4.1.272.4.5.61.1.14 | ColumnipNatOutOperType | read-only | current | Specifies whether there is an associated ipNatOutTable entry (permanent) or not (temporary). Note that entries with type permanent (1) cannot be deleted by the… |
| 1.3.6.1.4.1.272.4.5.61.1.15 | ColumnipNatOutOperParent | read-only | current | Row number of the associated ipNatOutTable entry. |
| 1.3.6.1.4.1.272.4.5.61.1.16 | ColumnipNatOutOperNatCategory | read-only | current | Specifies the NAT category according RFC 3489 and 5389 to be applied for UDP traffic matching with this entry. |
| 1.3.6.1.4.1.272.4.5.61.1.17 | ColumnipNatOutOperIntPortRange | read-only | current | This object specifies together with ipNatOutOperIntPort the internal source port range for which the table entry shall be valid. If this object is set to -1, o… |
| 1.3.6.1.4.1.272.4.5.61.1.18 | ColumnipNatOutOperExtPortRange | read-only | current | This object may be used together with ipNatOutOperExtPort to specify a fixed external source port number range to which the internal source port numbers are ma… |
| 1.3.6.1.4.1.272.4.5.63 | TableipNatPresetOperTable | not-accessible | current | This table specifies the IP addresses and port numbers for sessions requested from outside. If this table is empty and NAT is enabled, only packets for session… |
| 1.3.6.1.4.1.272.4.5.63.1 | RowipNatPresetOperEntry | not-accessible | current | |
| 1.3.6.1.4.1.272.4.5.63.1.1 | ColumnipNatPrOperIfIndex | read-only | current | This object specifies the interface index, for which the table entry shall be valid. If set to 0, the entry will be valid for all interfaces configured to use … |
| 1.3.6.1.4.1.272.4.5.63.1.2 | ColumnipNatPrOperProtocol | read-only | current | This object specifies the protocol, for which the table entry shall be valid. |
| 1.3.6.1.4.1.272.4.5.63.1.3 | ColumnipNatPrOperRemoteAddr | read-only | current | This object specifies together with ipNatPrOperRemoteMask the the set of IP addresses of remote hosts initiating a session. The table entry will be valid for a… |
| 1.3.6.1.4.1.272.4.5.63.1.4 | ColumnipNatPrOperRemoteMask | read-only | current | This object specifies together with ipNatPrOperRemoteAddr the set of IP addresses of remote hosts initiating the session. The table entry will be valid for an … |
| 1.3.6.1.4.1.272.4.5.63.1.5 | ColumnipNatPrOperExtAddr | read-only | current | This object specifies together with ipNatPrOperExtMask the set of destination IP addresses, for which the table entry shall be valid. The entry is valid, if th… |
| 1.3.6.1.4.1.272.4.5.63.1.6 | ColumnipNatPrOperExtMask | read-only | current | This object specifies together with ipNatPrOperExtAddr the set of destination IP addresses, for which the table entry shall be valid. The entry is valid, if th… |
| 1.3.6.1.4.1.272.4.5.63.1.7 | ColumnipNatPrOperExtPort | read-only | current | This object specifies together with ipNatPrOperExtPortRange the range of portnumbers for incoming packets, for which the table entry shall be valid. If both ob… |
| 1.3.6.1.4.1.272.4.5.63.1.8 | ColumnipNatPrOperExtPortRange | read-only | current | This object specifies together with ipNatPrOperExtPort the range of portnumbers for incoming packets, for which the table entry shall be valid. If both objects… |
| 1.3.6.1.4.1.272.4.5.63.1.9 | ColumnipNatPrOperIntAddr | read-only | current | With ipNatPrOperIntMask, this object specifies the internal target host's IP address for incoming packets matching the table entry. An incoming packet matching… |
| 1.3.6.1.4.1.272.4.5.63.1.10 | ColumnipNatPrOperIntPort | read-only | current | This object specifies the internal target host's port-number for incoming packets matching the table entry. If this object is set to -1, the target portnumber … |
| 1.3.6.1.4.1.272.4.5.63.1.11 | ColumnipNatPrOperIntMask | read-only | current | With ipNatPrOperIntAddr, this object specifies the internal target host's IP address for incoming packets matching the table entry. An incoming packet matching… |
| 1.3.6.1.4.1.272.4.5.63.1.12 | ColumnipNatPrOperTimeout | read-only | current | When there is no traffic associated with a NAT entry, this entry is discarded at the end of a timeout value. This object holds this timeout value in seconds. I… |
| 1.3.6.1.4.1.272.4.5.63.1.13 | ColumnipNatPrOperTcpOption | read-only | current | Additional selector, increases the prossible granularity of the TCP-related NAT preset rules. This parameter doesn't matter if not set, in all other cases init… |
| 1.3.6.1.4.1.272.4.5.63.1.14 | ColumnipNatPrOperType | read-only | current | Specifies whether there is an associated ipNatPrestTable entry (permanent) or not (temporary). Note that entries with type permanent (1) cannot be deleted by t… |
| 1.3.6.1.4.1.272.4.5.63.1.15 | ColumnipNatPrOperParent | read-only | current | Row number of the associated ipNatPresetTable entry. |
| 1.3.6.1.4.1.272.4.5.67 | TableipWolRuleTable | not-accessible | mandatory | The ipWolRuleTable defines access rules for checking incoming IP packets. The rules are processed in order, i.e. each rule has a link to the next rule. The set… |
| 1.3.6.1.4.1.272.4.5.67.1 | RowipWolRuleEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.5.67.1.1 | ColumnipWolRuleIndex | read-only | mandatory | Unique rule index. |
| 1.3.6.1.4.1.272.4.5.67.1.2 | ColumnipWolRuleFilterIndex | read-write | mandatory | References the rule's associated filter. |
| 1.3.6.1.4.1.272.4.5.67.1.3 | ColumnipWolRuleAction | read-write | mandatory | This object specifies the action to be performed if the rule's associated filter matches. If set to ignore the filter is not consulted and the next rule is pro… |
| 1.3.6.1.4.1.272.4.5.67.1.4 | ColumnipWolRuleNextRuleIndex | read-write | mandatory | Specifies the next rule to be processed. The value 0 is used to mark the end of the rule set. |
| 1.3.6.1.4.1.272.4.5.67.1.5 | ColumnipWolRuleWolType | read-write | mandatory | Which Wake-On-LAN standard should be used. |
| 1.3.6.1.4.1.272.4.5.67.1.6 | ColumnipWolRuleTarget | read-write | mandatory | The mac address of the interface to be woken up. |
| 1.3.6.1.4.1.272.4.5.67.1.7 | ColumnipWolRulePassword | read-write | mandatory | Wake-On-LAN password. The password length is either 0, 4 or 6. |
| 1.3.6.1.4.1.272.4.5.67.1.8 | ColumnipWolRuleDescr | read-write | current | A textual string describing this Wake-On-LAN rule. |
| 1.3.6.1.4.1.272.4.5.67.1.9 | ColumnipWolRuleTargetIfIndex | read-write | current | The index value which uniquely identifies Wake-On-LAN outbound interface. |
| 1.3.6.1.4.1.272.4.5.250 | IdentityipExtMIB | The MIB module for IP extended configuration and status. |