BINTEC-ISDN-MIB
175 objects
The MIB module for ISDN administration entities.
Imported Objects
| BINTEC-MIB MISSING | bibo BitValue Date HexValue isdn |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 enterprises Integer32 IpAddress mib-2 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DisplayString TimeStamp |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.272.4.57 | IdentityisdnMIB | The MIB module for ISDN administration entities. | ||
| 1.3.6.1.4.1.6666.1.1 | TableisdnIfTable | not-accessible | current | The isdnIfTable contains information relating to the interfaces found on the system. Each entry corresponds to a connected ISDN interface (BRI or PRI). Entries… |
| 1.3.6.1.4.1.6666.1.1.1 | RowisdnIfEntry | not-accessible | current | |
| 1.3.6.1.4.1.6666.1.1.1.1 | ColumnisdnIfIndex | read-only | current | Unique index of the basic or primary rate interface. |
| 1.3.6.1.4.1.6666.1.1.1.2 | ColumnisdnIfDescription | read-only | current | Textual description of the basic rate interface including its slot and number (e.g. bri2-0 means slot 2, unit 0). |
| 1.3.6.1.4.1.6666.1.1.1.3 | ColumnisdnIfLayer1State | read-only | current | The ISDN physical layer state according to I.430 f1(1) = inactive; f2(2) = sensing; f3(3) = deactivated; f4(4) = awaiting signal; f5(5) = identifying input; f6… |
| 1.3.6.1.4.1.6666.1.1.1.4 | ColumnisdnIfBchannelControl | read-only | current | B-channels are controlled by a call control protocol in the D-channel. Otherwise they may be used as permanent links. |
| 1.3.6.1.4.1.6666.1.1.1.5 | ColumnisdnIfActivationRequest | read-write | current | When this object is set to 'activate' the BRICK will start an activation sequence of ISDN-Layer1 of the basic rate interface. |
| 1.3.6.1.4.1.6666.1.1.1.6 | ColumnisdnIfMode | read-write | current | Specifies the mode of the interface. TE or NT Mode will be set for ISDN interfaces without PABX control. For PRI both NT (network termination) and TE (terminal… |
| 1.3.6.1.4.1.6666.1.1.1.7 | ColumnisdnIfTimerT3 | read-write | current | Value of Timer T3 in milliseconds.T3 is started whenever ISDNLayer-1 is activated (i.e. Activation Request is started). |
| 1.3.6.1.4.1.6666.1.1.1.8 | ColumnisdnIfUsePowerDetector | read-write | current | Use the PS1 Power Detector to control the layer 1 automaton.This object is only valid for basic rate interfaces. |
| 1.3.6.1.4.1.6666.1.1.1.9 | ColumnisdnIfNumberOfChannels | read-only | current | Number of Channels including the D channel, that are available on this ISDN Interface (3 = BRI, 31 = PRI). |
| 1.3.6.1.4.1.6666.1.1.1.10 | ColumnisdnIfTimeouts | read-only | current | Number of timeouts of T3 during lifetime of the system. |
| 1.3.6.1.4.1.6666.1.1.1.11 | ColumnisdnIfActivates | read-only | current | Number of successful activation cycles during lifetime of the system. |
| 1.3.6.1.4.1.6666.1.1.1.12 | ColumnisdnIfDeactivates | read-only | current | Number of deactivations during lifetime of the system. |
| 1.3.6.1.4.1.6666.1.1.1.13 | ColumnisdnIfAutoconfigState | read-write | current | Start auto configuration on this ISDN Interface. Auto configuration is a mechanism to automatically detect the attributes of an ISDN interface. This can be don… |
| 1.3.6.1.4.1.6666.1.1.1.14 | ColumnisdnIfAutoconfig | read-write | current | Start Autoconfiguration on this ISDN interface at bootup. |
| 1.3.6.1.4.1.6666.1.1.1.15 | ColumnisdnIfLicenseUsage | read-only | current | Shows which license type is currently used for this ISDN interface. |
| 1.3.6.1.4.1.6666.1.1.1.16 | ColumnisdnIfBriIfType | read-only | current | For some basic rate ISDN hardware it is possible to switch line interface type between S and U interface by using dedicated header modules. As this hardware pr… |
| 1.3.6.1.4.1.6666.1.1.1.17 | ColumnisdnIfAdminState | read-write | current | This variable allows for taking an ISDN interface out of/in service w/o having to touch the configuration. Besides, it is possible to initiate a reconfiguratio… |
| 1.3.6.1.4.1.6666.1.1.1.18 | ColumnisdnIfOperState | read-only | current | The operational state of an interface is indicated via this variable. Possible values are: - down(1), - running(2), - fail(3), - stopped(4), - stopping(5), - s… |
| 1.3.6.1.4.1.6666.1.1.1.21 | ColumnisdnIfSlips | read-only | current | Slip conditions detected since startup. Flags that the frequency of receive clock is different than frequency of internal system clock. |
| 1.3.6.1.4.1.6666.1.2 | TableisdnChTable | not-accessible | current | The isdnChTable contains information for each physical B or D channel on the system. The entries contain information regarding the configuration of the channel… |
| 1.3.6.1.4.1.6666.1.2.1 | RowisdnChEntry | not-accessible | current | |
| 1.3.6.1.4.1.6666.1.2.1.1 | ColumnisdnChIsdnIfIndex | read-only | current | Unique index of an Interface. |
| 1.3.6.1.4.1.6666.1.2.1.2 | ColumnisdnChNumber | read-only | current | The channel number. 0 is D-channel, 1..2 are the B- channels of a BRI module, and 1..31 are the B-channels of a PRI module. |
| 1.3.6.1.4.1.6666.1.2.1.3 | ColumnisdnChState | read-only | current | Status of the Channel controlled either by the call control protocol or the physical state of the interface. |
| 1.3.6.1.4.1.6666.1.2.1.4 | ColumnisdnChType | read-write | current | Type of Channel.Setting this object to one of the leased values creates a new entry in the ifTable. |
| 1.3.6.1.4.1.6666.1.2.1.5 | ColumnisdnChBundle | read-write | current | Index of the bundle to aggregate multiple Channels to one interface. Not valid in dialup mode. |
| 1.3.6.1.4.1.6666.1.2.1.6 | ColumnisdnChThroughput | read-only | current | Throughput of the channel in bits/second (64000 for B-channels, 16000 for BRI D-Channels. |
| 1.3.6.1.4.1.6666.1.2.1.7 | ColumnisdnChReceivedPackets | read-only | current | Count of received valid HDLC Frames. |
| 1.3.6.1.4.1.6666.1.2.1.8 | ColumnisdnChReceivedOctets | read-only | current | Count of received valid HDLC bytes. |
| 1.3.6.1.4.1.6666.1.2.1.9 | ColumnisdnChReceivedErrors | read-only | current | Count of received valid errors (can be detected by HDLC-Checksum-Errors). |
| 1.3.6.1.4.1.6666.1.2.1.10 | ColumnisdnChTransmitPackets | read-only | current | Count of received valid HDLC Frames. |
| 1.3.6.1.4.1.6666.1.2.1.11 | ColumnisdnChTransmitOctets | read-only | current | Count of received valid HDLC Frames. |
| 1.3.6.1.4.1.6666.1.2.1.12 | ColumnisdnChTransmitErrors | read-only | current | Count of transmitted valid HDLC errors. Can occur when the transmitter can not be reloaded fast enough when transmitting large packets. This should only happen… |
| 1.3.6.1.4.1.6666.1.2.1.13 | ColumnisdnChReceiveDiscards | read-only | current | Count of discarded received data frames. Can occur when the machine can not process fast enough the received frames. This should only happen when the system is… |
| 1.3.6.1.4.1.6666.1.2.1.14 | ColumnisdnChPhysicalBundle | read-write | current | Index of the bundle to aggregate multiple timeslots to one hyperchannel. Not valid in dialup mode. |
| 1.3.6.1.4.1.6666.1.3 | TableisdnStkTable | not-accessible | current | The isdnStkTable contains information for each ISDN protocol stack currently configured on the system. Entries are normally created by the system at boot time,… |
| 1.3.6.1.4.1.6666.1.3.1 | RowisdnStkEntry | not-accessible | current | |
| 1.3.6.1.4.1.6666.1.3.1.1 | ColumnisdnStkNumber | read-write | current | Unique number of an ISDN stack (0..n). This number can be used in the isdnDispatchTable. |
| 1.3.6.1.4.1.6666.1.3.1.3 | ColumnisdnStkIsdnIfIndex | read-write | current | The index of the ISDN interface. The isdnIfTable lists all available ISDN interfaces. |
| 1.3.6.1.4.1.6666.1.3.1.4 | ColumnisdnStkProtocolProfile | read-write | current | The protocol for the D channel. Assigning `delete' to this object has the effect of removing the entry from this table. |
| 1.3.6.1.4.1.6666.1.3.1.5 | ColumnisdnStkConfiguration | read-write | current | |
| 1.3.6.1.4.1.6666.1.3.1.6 | ColumnisdnStkSPID | read-write | current | The service profile identifier; only required for the national ISDN1 protocol in North America. |
| 1.3.6.1.4.1.6666.1.3.1.7 | ColumnisdnStkTeiProc | read-write | current | The Tei procedure used. Note that for point-to-point configurations this object should be set to fixed(2). |
| 1.3.6.1.4.1.6666.1.3.1.8 | ColumnisdnStkTeiValue | read-write | current | The Tei value. Note that for point-to-point configurations this object should be 0. |
| 1.3.6.1.4.1.6666.1.3.1.22 | ColumnisdnStkClearAllCalls | read-write | current | Setting this value to clear(2) will force all current connections on this stack to terminate. |
| 1.3.6.1.4.1.6666.1.3.1.23 | ColumnisdnStkStatus | read-only | current | Shows the status of this ISDN stack. If auto configuration was successful for this stack, this object will be loaded(1). If this stack is not loaded, ISDN call… |
| 1.3.6.1.4.1.6666.1.3.1.24 | ColumnisdnStkLayer2State | read-only | current | Shows the current state of Layer2. To allow ISDN connections, the state established(4) must be assigned. |
| 1.3.6.1.4.1.6666.1.3.1.25 | ColumnisdnStkBchannels | read-write | current | Number of B channels that correspond to that stack. |
| 1.3.6.1.4.1.6666.1.3.1.26 | ColumnisdnStkDialOutPrefix | read-write | current | Prefix for PABX dialout. This entry is added to a dialing number provided by the calling site via PPP negotiation (LCP Callback Option / PPP Callback Control P… |
| 1.3.6.1.4.1.6666.1.3.1.27 | ColumnisdnStkChannelSelection | read-write | current | Describes the coding of the Channel identification in outgoing ISDN-Setup messages. |
| 1.3.6.1.4.1.6666.1.4 | TableisdnCallTable | not-accessible | current | The isdnCallTable displays all currently active ISDN calls (incoming and outgoing). Only the system can add or remove entries to this table. Creating entries: … |
| 1.3.6.1.4.1.6666.1.4.1 | RowisdnCallEntry | not-accessible | current | |
| 1.3.6.1.4.1.6666.1.4.1.1 | ColumnisdnCallStkNumber | read-only | current | The number of the ISDN-Stack, this call is going through. Refer to the isdnStkTable. |
| 1.3.6.1.4.1.6666.1.4.1.2 | ColumnisdnCallType | read-only | current | The direction of the call. |
| 1.3.6.1.4.1.6666.1.4.1.3 | ColumnisdnCallReference | read-only | current | The corresponding Call-Reference Value on the ISDN D-channel. |
| 1.3.6.1.4.1.6666.1.4.1.4 | ColumnisdnCallAge | read-only | current | The age of the call. For outgoing calls, the time since the call began, or for incoming calls, the time since the call was received. The format is in hh:mm:ss.… |
| 1.3.6.1.4.1.6666.1.4.1.5 | ColumnisdnCallState | read-write | current | The state of the call. |
| 1.3.6.1.4.1.6666.1.4.1.6 | ColumnisdnCallIsdnIfIndex | read-only | current | The corresponding ISDN interface that is used for this call. Refer to the isdnIfTable. |
| 1.3.6.1.4.1.6666.1.4.1.7 | ColumnisdnCallChannel | read-only | current | The corresponding B-channel on this ISDN interface. Refer to the isdnIfTable. |
| 1.3.6.1.4.1.6666.1.4.1.8 | ColumnisdnCallDspItem | read-only | current | The item to or from which this call is connected. For any routing tasks (IP, IPX, X.25, bridging, ...) the ppp(1) item is used. For the isdnlogin program, logi… |
| 1.3.6.1.4.1.6666.1.4.1.9 | ColumnisdnCallRemoteNumber | read-only | current | The ISDN number that was called (for outgoing calls) or was calling (for incoming calls). |
| 1.3.6.1.4.1.6666.1.4.1.10 | ColumnisdnCallRemoteSubaddress | read-only | current | The subaddress of the remote number. The subaddress is coded in NSAP format as octets. See isdnCallRemoteNumber. |
| 1.3.6.1.4.1.6666.1.4.1.11 | ColumnisdnCallLocalNumber | read-only | current | The calling party number that was sent (with the outgoing call) or was received (with incoming calls). Refer to the isdnStkTable. |
| 1.3.6.1.4.1.6666.1.4.1.12 | ColumnisdnCallLocalSubaddress | read-only | current | The subaddress of the calling party number. See isdnCallRLocalNumber. |
| 1.3.6.1.4.1.6666.1.4.1.13 | ColumnisdnCallServiceIndicator | read-only | current | Service indicator that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.6666.1.4.1.14 | ColumnisdnCallAddInfo | read-only | current | Additional information that was sent on the ISDN D-channel when the call was established. Only sent/received when using the 1TR6 protocol. |
| 1.3.6.1.4.1.6666.1.4.1.15 | ColumnisdnCallBC | read-only | current | Bearer Capability that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.6666.1.4.1.16 | ColumnisdnCallLLC | read-only | current | Low Layer Capability that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.6666.1.4.1.17 | ColumnisdnCallHLC | read-only | current | The number of charging ticks received since this connection was established. Actual charges can be computed by multiplying this value with the unit price (e.g.… |
| 1.3.6.1.4.1.6666.1.4.1.18 | ColumnisdnCallCharge | read-only | current | This object contains the charge for this call either as units or as 1/1000 of the respective currency. Which type of information is choosen, depends on the inf… |
| 1.3.6.1.4.1.6666.1.4.1.19 | ColumnisdnCallReceivedPackets | read-only | current | Count of received valid HDLC Frames. |
| 1.3.6.1.4.1.6666.1.4.1.20 | ColumnisdnCallReceivedOctets | read-only | current | Count of received valid HDLC Octets. |
| 1.3.6.1.4.1.6666.1.4.1.21 | ColumnisdnCallReceivedErrors | read-only | current | Count of received invalid HDLC Frames. |
| 1.3.6.1.4.1.6666.1.4.1.22 | ColumnisdnCallTransmitPackets | read-only | current | Count of transmitted HDLC Frames. |
| 1.3.6.1.4.1.6666.1.4.1.23 | ColumnisdnCallTransmitOctets | read-only | current | Count of transmitted Octets. |
| 1.3.6.1.4.1.6666.1.4.1.24 | ColumnisdnCallTransmitErrors | read-only | current | Count of transmit errors (Collision, TX underrun). |
| 1.3.6.1.4.1.6666.1.4.1.25 | ColumnisdnCallChargeInfo | read-only | current | Textual information of charge, i.e. 0.12 DM or 3 units |
| 1.3.6.1.4.1.6666.1.4.1.26 | ColumnisdnCallScreening | read-only | current | Screening Indicator of the calling party number of incoming calls. The calling partys number (CPN) may be assigned either by the user placing the call or by th… |
| 1.3.6.1.4.1.6666.1.4.1.27 | ColumnisdnCallInfo | read-only | current | Additional information to identify the call |
| 1.3.6.1.4.1.6666.1.4.1.28 | ColumnisdnCallReceiveDiscards | read-only | current | Count of received and discarded data frames. |
| 1.3.6.1.4.1.6666.1.4.1.29 | ColumnisdnCallAssociatedIfIndex | read-only | current | The index of the associated virtual interface. |
| 1.3.6.1.4.1.6666.1.5 | TableisdnDispatchTable | not-accessible | current | The isdnDispatchTable is the central distribution center for all incoming ISDN connections. Incoming ISDN connections are `dispatched' to a service (isdnDspIte… |
| 1.3.6.1.4.1.6666.1.5.1 | RowisdnDispatchEntry | not-accessible | current | |
| 1.3.6.1.4.1.6666.1.5.1.1 | ColumnisdnDspStkNumber | read-write | current | The ISDN stack number for this entry. |
| 1.3.6.1.4.1.6666.1.5.1.2 | ColumnisdnDspItem | read-write | current | The item to connect this call to. Routing tasks (IP, IPX, X.25, bridging, ...) should use the ppp(1). For the isdnlogin program use the login(2) item. For CAPI… |
| 1.3.6.1.4.1.6666.1.5.1.3 | ColumnisdnDspLocalNumber | read-write | current | If the Called Party Number of the incoming call on the specified ISDN stack matches this value, the call is dispatched to the defined item. For outgoing calls … |
| 1.3.6.1.4.1.6666.1.5.1.4 | ColumnisdnDspLocalSubaddress | read-write | current | If the Called Party Subaddress of the incoming call on the specified ISDN stack matches this value, the call is dispatched to the defined item. For outgoing ca… |
| 1.3.6.1.4.1.6666.1.5.1.5 | ColumnisdnDspBearer | read-write | current | The isdnDspBearer is used for dispatching different types of calls |
| 1.3.6.1.4.1.6666.1.5.1.6 | ColumnisdnDspSlot | read-write | current | Identification number of the used slot. |
| 1.3.6.1.4.1.6666.1.5.1.7 | ColumnisdnDspUnit | read-write | current | Identification number of the used unit. |
| 1.3.6.1.4.1.6666.1.5.1.8 | ColumnisdnDspDirection | read-write | current | Specifies whether the entry is to be used for outgoing calls, incoming calls or both. |
| 1.3.6.1.4.1.6666.1.5.1.9 | ColumnisdnDspMode | read-write | current | This object specifies the matching direction for incoming calls. When set to right-to-left, the rightmost digits of the called address of an incoming call are … |
| 1.3.6.1.4.1.6666.1.5.1.10 | ColumnisdnDspUserName | read-write | current | The name of the user. |
| 1.3.6.1.4.1.6666.1.5.1.11 | ColumnisdnDspRemoteNumber | read-write | current | If this variable is non-empty it defines which calling party number must be contained in an incoming call in order of this entry to match. Together with variab… |
| 1.3.6.1.4.1.6666.1.5.1.12 | ColumnisdnDspRemoteSubaddress | read-write | current | This variable specifies a calling party subaddress which must be contained in an incoming call when this entry. Right as with isdnDspRemoteNumber there are no … |
| 1.3.6.1.4.1.6666.1.5.1.13 | ColumnisdnDspTypeOfLocalSubAdd | read-write | current | The type of called subaddress may be specified here. Possible values are ... any(1) type of subaddress doesn't matter user(2) subaddress of type user (as of ET… |
| 1.3.6.1.4.1.6666.1.5.1.14 | ColumnisdnDspTypeOfRemoteSubAdd | read-write | current | The type of calling subaddress may be specified here. Possible values are ... any(1) type of subaddress doesn't matter user(2) subaddress of type user (as of E… |
| 1.3.6.1.4.1.6666.1.5.1.15 | ColumnisdnDspMpsMsnIndex | read-write | current | This variable is only valid for devices with MPS. It defines, together with isdnDspMsnTrunkGroupIndex the external number and thereby overwrites isdnDspLocalNu… |
| 1.3.6.1.4.1.6666.1.5.1.16 | ColumnisdnDspMpsMsnTrunkGroupIndex | read-write | current | Determines isdnDspLocalNumber in devices with MPS subsystem. See description of isdnDspMsnIndex for further informations. Default value is 0 being an invalid i… |
| 1.3.6.1.4.1.6666.1.5.1.17 | ColumnisdnDspMpsExtensionIndex | read-write | current | For devices with MPS subsystem this variable references the mpsExtension table entry with a mpsExtensionIndex identical to the one specified in here. This vari… |
| 1.3.6.1.4.1.6666.1.6 | TableisdnDChanX31Table | not-accessible | current | The isdnDChanX31Table contains information for the X.31 stack for each available ISDN D-channel. This information is mainly used for X.25 packet-switching func… |
| 1.3.6.1.4.1.6666.1.6.1 | RowisdnDChanX31Entry | not-accessible | current | |
| 1.3.6.1.4.1.6666.1.6.1.1 | ColumnisdnX31IsdnIfIndex | read-write | current | The corresponding ISDN interface that is used for this call. Refer to the isdnIfTable. |
| 1.3.6.1.4.1.6666.1.6.1.2 | ColumnisdnX31TeiProc | read-write | current | The procedure used for polling of TEI (terminal end-point identifiers) values. |
| 1.3.6.1.4.1.6666.1.6.1.3 | ColumnisdnX31TeiValue | read-write | current | The TEI value for this interface. |
| 1.3.6.1.4.1.6666.1.6.1.5 | ColumnisdnX31AssignedTo | read-write | current | The service this TEI value is assigned to. |
| 1.3.6.1.4.1.6666.1.6.1.6 | ColumnisdnX31IsdnPTIfIndex | read-write | current | The corresponding ISDN interface that is used as destination for this call in case variable isdnX31AssignedTo contains value pass-through. Refer to isdnIfTable. |
| 1.3.6.1.4.1.6666.1.7 | ScalarisdnAccountingTemplate | read-write | current | Specifies the format of accounting messages sent by the syslog protocol. The format can consist of any order of the following variables. Tag Meaning %S Date th… |
| 1.3.6.1.4.1.6666.1.8 | TableisdnCallHistoryTable | not-accessible | current | The isdnCallHistoryTable contains information pertaining to the last 20 ISDN calls made, since the last system startup. Each call that appears in the isdnCallT… |
| 1.3.6.1.4.1.6666.1.8.1 | RowisdnCallHistoryEntry | not-accessible | current | |
| 1.3.6.1.4.1.6666.1.8.1.1 | ColumnisdnCallHistoryStkNumber | read-only | current | The number of the ISDN-Stack, this call went through. |
| 1.3.6.1.4.1.6666.1.8.1.2 | ColumnisdnCallHistoryType | read-only | current | The direction of the call, incoming or outgoing. |
| 1.3.6.1.4.1.6666.1.8.1.3 | ColumnisdnCallHistoryTime | read-only | current | The time the call was received (incoming) or was placed (outgoing). |
| 1.3.6.1.4.1.6666.1.8.1.4 | ColumnisdnCallHistoryDuration | read-only | current | The duration of the call in seconds. |
| 1.3.6.1.4.1.6666.1.8.1.5 | ColumnisdnCallHistoryIsdnIfIndex | read-only | current | The corresponding ISDN interface that this call used. |
| 1.3.6.1.4.1.6666.1.8.1.6 | ColumnisdnCallHistoryChannel | read-only | current | The corresponding B-channel on this ISDN interface. |
| 1.3.6.1.4.1.6666.1.8.1.7 | ColumnisdnCallHistoryDspItem | read-only | current | The item this call was connected to. Routing tasks (IP, IPX, X.25, bridging, ...) use ppp(1). The isdnlogin program uses login(2). CAPI 1.1 programs, use the i… |
| 1.3.6.1.4.1.6666.1.8.1.8 | ColumnisdnCallHistoryRemoteNumber | read-only | current | The ISDN number that was called (for outgoing calls) or was calling (for incoming calls). |
| 1.3.6.1.4.1.6666.1.8.1.9 | ColumnisdnCallHistoryRemoteSubaddress | read-only | current | The subaddress of the remote number. See isdnCall- HistoryRemoteNumber. |
| 1.3.6.1.4.1.6666.1.8.1.10 | ColumnisdnCallHistoryLocalNumber | read-only | current | The calling party number that was sent (with the outgoing call) or was received (with incoming calls). |
| 1.3.6.1.4.1.6666.1.8.1.11 | ColumnisdnCallHistoryLocalSubaddress | read-only | current | The subaddress of the calling party number. |
| 1.3.6.1.4.1.6666.1.8.1.12 | ColumnisdnCallHistoryServiceIndicator | read-only | current | Service indicator that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.6666.1.8.1.13 | ColumnisdnCallHistoryAddInfo | read-only | current | Additional information that was sent on the ISDN D-channel when the call was established. Only sent/received when using the 1TR6 protocol. |
| 1.3.6.1.4.1.6666.1.8.1.14 | ColumnisdnCallHistoryBC | read-only | current | Bearer Capability that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.6666.1.8.1.15 | ColumnisdnCallHistoryLLC | read-only | current | Low Layer Capability that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.6666.1.8.1.16 | ColumnisdnCallHistoryHLC | read-only | current | High Layer Capability that was sent on the ISDN D-channel when the call was established. |
| 1.3.6.1.4.1.6666.1.8.1.17 | ColumnisdnCallHistoryCharge | read-only | current | The number of charging ticks received for this connection. Actual charges can be computed by multiplying this value with the unit price, e.g. .12 DM in Germany… |
| 1.3.6.1.4.1.6666.1.8.1.18 | ColumnisdnCallHistoryDSS1Cause | read-only | current | ISDN error condition reported by the DSS1 protocol, for Euro ISDN. See Software Reference Manual. |
| 1.3.6.1.4.1.6666.1.8.1.19 | ColumnisdnCallHistory1TR6Cause | read-only | current | ISDN error condition reported by the 1TR6 protocol, for National ISDN in Germany. See Software Reference Manual. |
| 1.3.6.1.4.1.6666.1.8.1.20 | ColumnisdnCallHistoryLocalCause | read-only | current | ISDN error condition reported by the system locally. See Software Reference Manual. |
| 1.3.6.1.4.1.6666.1.8.1.21 | ColumnisdnCallHistoryChargeInfo | read-only | current | Textual information of charge, i.e. 0.12 DM or 3 units |
| 1.3.6.1.4.1.6666.1.8.1.22 | ColumnisdnCallHistoryScreening | read-only | current | Screening Indicator of the calling party number of incoming calls. The calling partys number (CPN) may be assigned either by the user placing the call or by th… |
| 1.3.6.1.4.1.6666.1.8.1.23 | ColumnisdnCallHistoryInfo | read-only | current | Additional information to identify the call |
| 1.3.6.1.4.1.6666.1.8.1.24 | ColumnisdnCallHistoryReceivedPackets | read-only | current | Count of received valid HDLC Frames. |
| 1.3.6.1.4.1.6666.1.8.1.25 | ColumnisdnCallHistoryReceivedOctets | read-only | current | Count of received valid HDLC Octets. |
| 1.3.6.1.4.1.6666.1.8.1.26 | ColumnisdnCallHistoryReceivedErrors | read-only | current | Count of received invalid HDLC Frames. |
| 1.3.6.1.4.1.6666.1.8.1.27 | ColumnisdnCallHistoryTransmitPackets | read-only | current | Count of transmitted HDLC Frames. |
| 1.3.6.1.4.1.6666.1.8.1.28 | ColumnisdnCallHistoryTransmitOctets | read-only | current | Count of transmitted Octets. |
| 1.3.6.1.4.1.6666.1.8.1.29 | ColumnisdnCallHistoryTransmitErrors | read-only | current | Count of transmit errors (Collision, TX underrun). |
| 1.3.6.1.4.1.6666.1.8.1.30 | ColumnisdnCallHistoryReceiveDiscards | read-only | current | Count of received and discarded data frames. |
| 1.3.6.1.4.1.6666.1.8.1.31 | ColumnisdnCallHistoryAssociatedIfIndex | read-only | current | The index of the associated virtual interface. |
| 1.3.6.1.4.1.6666.1.9 | ScalarisdnLoginOnPPPDispatch | read-write | current | Allows or disallows incoming ISDN calls (with an ISDN service indicator of 'telephony'), to be connected to the isdnlogin daemon even though the call has a mat… |
| 1.3.6.1.4.1.6666.1.10 | ScalarisdnHistoryMaxEntries | read-write | current | Maximum number of isdnCallHistory entries in memory. |
| 1.3.6.1.4.1.6666.1.11 | TableisdnloginAllowTable | not-accessible | current | The isdnloginAllowTable contains information about the ISDN partners that are allowed to login to the BRICK via the isdnlogin service. ISDN callers are identif… |
| 1.3.6.1.4.1.6666.1.11.1 | RowisdnloginAllowEntry | not-accessible | current | |
| 1.3.6.1.4.1.6666.1.11.1.1 | ColumnisdnloginAllowStkNumber | read-write | current | The number of the ISDN stack, that accepts incoming isdnlogin calls. Refer to the isdnStkTable. The value `-1' matches all available stacks. |
| 1.3.6.1.4.1.6666.1.11.1.2 | ColumnisdnloginAllowRemoteNumber | read-write | current | The number of the ISDN partner that is allowed to login via isdnlogin through the corresponding ISDN Stack. The wildcards '*', '?', '[', ']', '{', '}' may be u… |
| 1.3.6.1.4.1.6666.1.11.1.3 | ColumnisdnloginAllowRemoteSubaddress | read-write | current | The subaddress of the remote number. The subaddress is coded in NSAP format as octets. See isdnloginAllowRemoteNumber. |
| 1.3.6.1.4.1.6666.1.11.1.4 | ColumnisdnloginAllowScreening | read-write | current | The screening indicator of the calling party number (CPN). The isdnloginAllowScreening field can be used to gauge the `trustworthiness' of the CPN field (see i… |
| 1.3.6.1.4.1.6666.1.12 | TableisdnCreditsTable | not-accessible | current | The isdnCreditsTable contains informations about current used resources and maximum allowed resources for each during a specified interval subsystem. Creating … |
| 1.3.6.1.4.1.6666.1.12.1 | RowisdnCreditsEntry | not-accessible | current | |
| 1.3.6.1.4.1.6666.1.12.1.1 | ColumnisdnCreditsSubsysNumber | read-only | current | Type of Subsystem. |
| 1.3.6.1.4.1.6666.1.12.1.2 | ColumnisdnCreditsSurveillance | read-write | current | Surveillance on or off. |
| 1.3.6.1.4.1.6666.1.12.1.3 | ColumnisdnCreditsMeasuretime | read-write | current | Time of one observation interval in seconds. |
| 1.3.6.1.4.1.6666.1.12.1.4 | ColumnisdnCreditsMaxInCon | read-write | current | Maximum number of allowed incoming connections during the observation interval. -1 disables this limit. |
| 1.3.6.1.4.1.6666.1.12.1.5 | ColumnisdnCreditsMaxOutCon | read-write | current | Maximum number of allowed outgoing connections during the observation interval. -1 disables this limit. |
| 1.3.6.1.4.1.6666.1.12.1.6 | ColumnisdnCreditsMaxCharge | read-write | current | Maximum allowed charge amount during the observation interval. -1 disables this limit. |
| 1.3.6.1.4.1.6666.1.12.1.7 | ColumnisdnCreditsMaxInDuration | read-write | current | Maximum connect time for incoming connections in seconds during the observation interval. -1 disables this limit. |
| 1.3.6.1.4.1.6666.1.12.1.8 | ColumnisdnCreditsMaxOutDuration | read-write | current | Maximum connect time for outgoing connections in seconds during the observation interval. -1 disables this limit |
| 1.3.6.1.4.1.6666.1.12.1.9 | ColumnisdnCreditsTimeleft | read-write | current | Time in seconds left in current interval. Writing to Timeleft will restart the observation interval. |
| 1.3.6.1.4.1.6666.1.12.1.10 | ColumnisdnCreditsCurrentInCon | read-only | current | Current number of incoming connections. |
| 1.3.6.1.4.1.6666.1.12.1.11 | ColumnisdnCreditsCurrentOutCon | read-only | current | Current number of outgoing connections. |
| 1.3.6.1.4.1.6666.1.12.1.12 | ColumnisdnCreditsTotalInCon | read-only | current | Total count of incoming connections during the observation interval. |
| 1.3.6.1.4.1.6666.1.12.1.13 | ColumnisdnCreditsTotalOutCon | read-only | current | Total count of outgoing connections during the observation interval. |
| 1.3.6.1.4.1.6666.1.12.1.14 | ColumnisdnCreditsTotalMaxCon | read-only | current | Maximum number of simultaniously established connections during the observation interval. |
| 1.3.6.1.4.1.6666.1.12.1.15 | ColumnisdnCreditsTotalCharge | read-only | current | Total accounted charge during the observation interval. |
| 1.3.6.1.4.1.6666.1.12.1.16 | ColumnisdnCreditsTotalInDuration | read-only | current | Total connect time of incoming connections during the observation interval. |
| 1.3.6.1.4.1.6666.1.12.1.17 | ColumnisdnCreditsTotalOutDuration | read-only | current | Total connect time of outgoing connections during the observation interval. |
| 1.3.6.1.4.1.6666.1.12.1.18 | ColumnisdnCreditsMaxCurrentInCon | read-write | current | Maximum number of currently allowed incoming connections. -1 disables this limit. |
| 1.3.6.1.4.1.6666.1.12.1.19 | ColumnisdnCreditsMaxCurrentOutCon | read-write | current | Maximum number of currently allowed outgoing connections. -1 disables this limit. |
| 1.3.6.1.4.1.6666.1.12.1.20 | ColumnisdnCreditsMaxCurrentCon | read-write | current | Maximum number of currently allowed connections in both directions. -1 disables this limit. |
| 1.3.6.1.4.1.6666.1.13 | ScalarisdnLoginSpeechMode | read-write | current | GFK request for modem dial in also if the requested service is not voice |