BROTHER-MIB
1304 objects
No module-level DESCRIPTION found.
Imported Objects
| IPV6-TC | Ipv6Address |
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises IpAddress |
| RFC1213-MIB | DisplayString |
| SNMPv2-TC | DateAndTime |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2435 | Nodebrother | |||
| 1.3.6.1.4.1.2435.2 | Nodenm | |||
| 1.3.6.1.4.1.2435.2.3 | Nodesystem | |||
| 1.3.6.1.4.1.2435.2.3.9 | Nodenet-peripheral | |||
| 1.3.6.1.4.1.2435.2.3.9.1 | Nodenet-printer | |||
| 1.3.6.1.4.1.2435.2.3.9.1.1 | NodegeneralDeviceStatus | |||
| 1.3.6.1.4.1.2435.2.3.9.1.1.2 | Nodestatus | |||
| 1.3.6.1.4.1.2435.2.3.9.1.1.2.9 | ScalarbrJamPlace | read-only | mandatory | Location of JAM. 0:No Jam 1:Jam Trays 2:Jam Inside 3:Jam Rear 4:Jam Duplex unit |
| 1.3.6.1.4.1.2435.2.3.9.1.1.2.10 | Nodetonerlow | |||
| 1.3.6.1.4.1.2435.2.3.9.1.1.2.10.1 | ScalarbrToner1Low | read-only | mandatory | Black Toner status. 0:Toner Full 1:Toner Low 2:No Toner Cartridge 3:Toner Empty |
| 1.3.6.1.4.1.2435.2.3.9.1.1.2.10.2 | ScalarbrToner2Low | read-only | mandatory | Cyan Toner status. 0:Toner Ready 1:Toner Low 2:No Toner Cartridge 3:Toner Empty |
| 1.3.6.1.4.1.2435.2.3.9.1.1.2.10.3 | ScalarbrToner3Low | read-only | mandatory | Magenta Toner status. 0:Toner Ready 1:Toner Low 2:No Toner Cartridge 3:Toner Empty |
| 1.3.6.1.4.1.2435.2.3.9.1.1.2.10.4 | ScalarbrToner4Low | read-only | mandatory | Yellow Toner status. 0:Toner Ready 1:Toner Low 2:No Toner Cartridge 3:Toner Empty |
| 1.3.6.1.4.1.2435.2.3.9.1.1.7 | Scalarbrieee1284id | read-only | mandatory | IEEE1284 device ID |
| 1.3.6.1.4.1.2435.2.3.9.1.1.10 | Scalarbrttt1 | read-only | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.2 | Nodenet-MFP | |||
| 1.3.6.1.4.1.2435.2.3.9.2.1 | Nodefax-setup | |||
| 1.3.6.1.4.1.2435.2.3.9.2.1.1 | Nodeautodial | |||
| 1.3.6.1.4.1.2435.2.3.9.2.1.1.1 | NodeonetouchDial | |||
| 1.3.6.1.4.1.2435.2.3.9.2.1.1.1.1 | ScalarbrOneTouchDialCount | read-only | mandatory | Maximum number of One touch dial. |
| 1.3.6.1.4.1.2435.2.3.9.2.1.1.1.2 | TablebrOneTouchDialTable | not-accessible | mandatory | This table represents One touch dial. |
| 1.3.6.1.4.1.2435.2.3.9.2.1.1.1.2.1 | RowbrOneTouchDialEntry | not-accessible | mandatory | A row in the OneTouchDial table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.2.1.1.1.2.1.1 | ColumnbrOneTouchDialIndex | read-only | mandatory | The One touch dial number. |
| 1.3.6.1.4.1.2435.2.3.9.2.1.1.1.2.1.2 | ColumnbrOneTouchDialData | read-write | mandatory | The One Touch dial data. |
| 1.3.6.1.4.1.2435.2.3.9.2.1.1.2 | NodespeedDial | |||
| 1.3.6.1.4.1.2435.2.3.9.2.1.1.2.1 | ScalarbrSpeedDialCount | read-only | mandatory | Maximum number of Speed dial. |
| 1.3.6.1.4.1.2435.2.3.9.2.1.1.2.2 | TablebrSpeedDialTable | not-accessible | mandatory | This table represents Speed dial. |
| 1.3.6.1.4.1.2435.2.3.9.2.1.1.2.2.1 | RowbrSpeedDialEntry | not-accessible | mandatory | A row in the speedDial table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.2.1.1.2.2.1.1 | ColumnbrSpeedDialIndex | read-only | mandatory | The Speed dial number. |
| 1.3.6.1.4.1.2435.2.3.9.2.1.1.2.2.1.2 | ColumnbrSpeedDialData | read-write | mandatory | The Speed dial Data. |
| 1.3.6.1.4.1.2435.2.3.9.2.1.1.3 | ScalarbrDialDataAllClear | read-write | mandatory | Clear the all data of Onetouch dial and Speed dial. |
| 1.3.6.1.4.1.2435.2.3.9.2.1.2 | Nodefax-general | |||
| 1.3.6.1.4.1.2435.2.3.9.2.1.2.1 | ScalarbrFaxReceiveMode | read-write | mandatory | Fax Receive Mode 0:Auto 1:Manual 2:FaxTel 3:TAD |
| 1.3.6.1.4.1.2435.2.3.9.2.1.2.2 | ScalarbrRingDelayCount | read-write | mandatory | Ring Delay Count |
| 1.3.6.1.4.1.2435.2.3.9.2.1.2.3 | ScalarbrOwnFaxNumber | read-write | mandatory | Own Fax Number |
| 1.3.6.1.4.1.2435.2.3.9.2.11 | Nodescanner-setup | |||
| 1.3.6.1.4.1.2435.2.3.9.2.11.1 | NodescanToInfo | |||
| 1.3.6.1.4.1.2435.2.3.9.2.11.1.1 | ScalarbrRegisterKeyInfo | read-write | mandatory | Add the ScanTo information. If device receives GET request, device should reply fix value TRUE(writable), FALSE(not writable) to the client. |
| 1.3.6.1.4.1.2435.2.3.9.2.11.1.2 | ScalarbrUnRegisterKeyInfo | read-write | mandatory | Remove the ScanTo information. If device receives GET request, device should reply fix value TRUE (writable), FALSE (not writable) to the client. |
| 1.3.6.1.4.1.2435.2.3.9.2.11.1.5 | ScalarbrNetSKeyReceiverAddress | read-write | mandatory | IP Address or the name of the S-Key Receiver. |
| 1.3.6.1.4.1.2435.2.3.9.2.101 | NodemfpCapability | |||
| 1.3.6.1.4.1.2435.2.3.9.2.101.1 | NodemcGeneral | |||
| 1.3.6.1.4.1.2435.2.3.9.2.101.1.11 | NodemcgRemoteSetup | |||
| 1.3.6.1.4.1.2435.2.3.9.2.101.1.11.1 | ScalarbrNetRemoteSetUpSupported | read-only | mandatory | 0 indicates the Net Remote Setup function is not supported. 1 indicates the Net Remote Setup function is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.3.9.2.101.1.11.2 | ScalarbrNetRemoteSetUpEnable | read-write | mandatory | 0 indicates the Net Remote Setup is not enabled. 1 indicates that the Net Remote Setup is enabled. Writing a non-zero value will enable the Net Remote Setup if… |
| 1.3.6.1.4.1.2435.2.3.9.2.101.1.11.3 | ScalarbrNetRemoteSetUpFileFormat | read-only | mandatory | It is a file format of the Net Remote Setup function. |
| 1.3.6.1.4.1.2435.2.3.9.2.101.2 | NodemcFax | |||
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.1 | NodemcfGeneral | |||
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.1.1 | ScalarbrFaxSupported | read-only | mandatory | 0 indicates the Fax function is not supported. 1 indicates the Fax function is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.1.3 | ScalarbrIFaxSupported | read-only | mandatory | 0 indicates the IFax function is not supported. 1 indicates the IFax function is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.11 | NodemcfNetFaxShare | |||
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.11.1 | ScalarbrNetFaxShareSupported | read-only | mandatory | 0 indicates the Net Fax Share is not supported. 1 indicates the Net Fax Share is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.11.2 | ScalarbrNetFaxShareEnable | read-write | mandatory | 0 indicates the Net Fax Share is not enabled. 1 indicates that the Net Fax Share is enabled. Writing a non-zero value will enable the Net Fax Share if it is su… |
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.12 | NodemcfNetPcFaxRx | |||
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.12.1 | ScalarbrNetPcFaxRxSupported | read-only | mandatory | 0 indicates the Net PC Fax Rx is not supported. 1 indicates the Net PC Fax Rx is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.12.2 | ScalarbrNetPcFaxRxEnable | read-write | mandatory | 0 indicates the Net PC Fax Rx is not enabled. 1 indicates that the Net PC Fax Rx is enabled. Writing a non-zero value will enable the Net PC Fax Rx if it is su… |
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.12.3 | ScalarbrNetRegisterPcFaxInfo | read-write | mandatory | Add the PcFax information. If device receives GET request, device should reply fix value TRUE(writable), FALSE(not writable) to the client. |
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.101 | NodemcfFaxInfomation | |||
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.101.1 | ScalarbrPhoneNumberLastFax | read-only | mandatory | Phone Number of Last Fax |
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.101.2 | ScalarbrPagesSentLastFax | read-only | mandatory | Pages Sent in Last Fax |
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.101.3 | ScalarbrTimestampLastFax | read-only | mandatory | Timestamp of Last Fax |
| 1.3.6.1.4.1.2435.2.3.9.2.101.2.101.4 | ScalarbrFaxHeaderInfo | read-write | mandatory | Fax Header Infomation |
| 1.3.6.1.4.1.2435.2.3.9.2.101.3 | NodemcScanner | |||
| 1.3.6.1.4.1.2435.2.3.9.2.101.3.11 | NodemcsNetScanner | |||
| 1.3.6.1.4.1.2435.2.3.9.2.101.3.11.1 | ScalarbrNetScannerSupported | read-only | mandatory | 0 indicates the Net Scanner is not supported. 1 indicates the Net Scanner is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.3.9.2.101.3.11.2 | ScalarbrNetScannerEnable | read-write | mandatory | 0 indicates the Net Scanner is not enabled. 1 indicates that the Net Scanner is enabled. Writing a non-zero value will enable the Net Scanner if it is supporte… |
| 1.3.6.1.4.1.2435.2.3.9.2.101.3.12 | NodemcsNetSKy | |||
| 1.3.6.1.4.1.2435.2.3.9.2.101.3.12.1 | ScalarbrNetSKeySupported | read-only | mandatory | 0 indicates the Net S-Key is not supported. 1 indicates the Net S-Key is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.3.9.2.101.3.12.2 | ScalarbrNetSKeyEnable | read-write | mandatory | 0 indicates the Net S-Key is not enabled. 1 indicates that the Net S-Key is enabled. Writing a non-zero value will enable the Net S-Key if it is supported by t… |
| 1.3.6.1.4.1.2435.2.3.9.2.111 | Nodemfpgeneral-setup | |||
| 1.3.6.1.4.1.2435.2.3.9.2.111.1 | ScalarbrServiceMode | read-write | mandatory | Service Mode |
| 1.3.6.1.4.1.2435.2.3.9.2.111.2 | ScalarbrLockMode | read-write | mandatory | Lock Mode 0:normal 1:Customer 2:Lock |
| 1.3.6.1.4.1.2435.2.3.9.2.111.3 | ScalarbrActivityReportSetting | read-write | mandatory | Activity Report Setting 0:off 1:every 1hour 3:every 3hour 6:every 6hour 12:every 12hour 24:every 24hour 48:every 2day 96:every 4day 240:every Sunday 241:every … |
| 1.3.6.1.4.1.2435.2.3.9.4 | NodenetPML | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2 | NodenetPMLmgmt | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1 | Nodedevice | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1 | Nodedestination-subsystem1 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.1 | Nodesleep | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.1.1 | Scalarbrpowerstime | read-write | mandatory | PowerSave Timeout value. 1 to 2147483647 (sec) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.2 | Nodeautoc | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.2.7 | Scalarbrautocont | read-write | mandatory | Auto Continue. 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4 | Nodesimm | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1 | Nodespecification | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.1 | Nodesimmkind0 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.1.4 | Scalarbrsimmtype0 | read-only | mandatory | SIMM type on slot0. 0: unconfirmed : 0 MB 1: empty 2: unconfirmed 3: No Supported : 0 MB 4: Read Only Memory 5: Volatility RAM : size MB 6: Un Volatility RAM :… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.1.5 | Scalarbrsimmsize0 | read-only | mandatory | SIMM size on slot0 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.2 | Nodesimmkind1 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.2.4 | Scalarbrsimmtype1 | read-only | mandatory | SIMM type on slot1. 0: unconfirmed : 0 MB 1: empty 2: unconfirmed 3: No Supported : 0 MB 4: Read Only Memory 5: Volatility RAM : size MB 6: Un Volatility RAM :… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.2.5 | Scalarbrsimmsize1 | read-only | mandatory | SIMM size on slot1 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.3 | Nodesimmkind2 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.3.4 | Scalarbrsimmtype2 | read-only | mandatory | SIMM type on slot2. 0: unconfirmed : 0 MB 1: empty 2: unconfirmed 3: No Supported : 0 MB 4: Read Only Memory 5: Volatility RAM : size MB 6: Un Volatility RAM :… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.3.5 | Scalarbrsimmsize2 | read-only | mandatory | SIMM size on slot2. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.4 | Nodesimmkind3 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.4.4 | Scalarbrsimmtype3 | read-only | mandatory | SIMM type on slot3. 0: unconfirmed : 0 MB 1: empty 2: unconfirmed 3: No Supported : 0 MB 4: Read Only Memory 5: Volatility RAM : size MB 6: Un Volatility RAM :… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.1.4.5 | Scalarbrsimmsize3 | read-only | mandatory | SIMM type on slot3. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.3 | Nodebio1-explanation | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.3.1 | Nodedetermined | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.1.4.3.1.4 | ScalarbrTBD1 | read-write | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.2 | Nodedestination-subsystem2 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.2.1 | Nodeprinterjob | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.2.1.1 | Nodejobend | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.2.1.1.1 | Scalarbrtimeout | read-write | mandatory | Job Timeout. 1 to 2147483647(sec) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.2.1.1.5 | ScalarbrTBD2 | read-write | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3 | Nodedestination-subsystem3 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3 | Nodeprt-setup | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1 | Nodeprt-condition | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.1 | Scalarbrpersonality | read-write | mandatory | Printer Emulation setting. 1:PCL 2:HPGL 4:PS 5:AUTO 6:IBM 7:EPSON 8:HBP |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.2 | Scalarbrorientation | read-write | mandatory | Default Paper Orientation. 1:portrait 2:landscape |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.4 | Scalarbrcopies | read-write | mandatory | Default Copy Pages. 1-999 pages |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.6 | ScalarbrTBD3 | read-write | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.8 | Scalarbrresolution | read-write | mandatory | Default Resolution. 300, 600 or 1200dpi |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.10 | Scalarbrpageprotect | read-write | mandatory | Page Protect mode 1:Off 3:Auto 4:Letter 5:Legal 6:A4 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.11 | Scalarbrlines | read-write | mandatory | lines per page. 5-128 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.13 | Scalarbrpaper | read-write | mandatory | Default Paper size. -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 … |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.22 | Scalarbrpapertype | read-write | mandatory | Default Media type. 0:Regular 1:Thick paper 2:Thicker paper 3:Transparency 4:Thin paper 5:Bond paper 6:ENVELOPES 7:ENV. THICK 8:ENV. THIN 9:RECYCLED 10:HAGAKI … |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.23 | Scalarbrpapertype2 | read-write | mandatory | Default Media type. 0:Regular 1:Thick paper 2:Thicker paper 3:Transparency 4:Thin paper 5:Bond paper 6:ENVELOPES 7:ENV. THICK 8:ENV. THIN 9:RECYCLED 10:HAGAKI … |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.3.3.1.26 | ScalarbrpapertypeMP | read-write | mandatory | Default Media type. 0:Regular 1:Thick paper 2:Thicker paper 3:Transparency 4:Thin paper 5:Bond paper 6:ENVELOPES 7:ENV. THICK 8:ENV. THIN 9:RECYCLED 10:HAGAKI … |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4 | Nodedestination-subsystem4 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1 | Nodeprint-engine | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.1 | Nodeprt-density | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.1.5 | Scalarbrdensity | read-write | mandatory | Print Density. -15..15 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.2 | Nodestatus-prt-eng | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3 | Nodetray | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.1 | Nodemanual | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.1.4 | Scalarbrmanualfeed | read-write | mandatory | Manualfeed mode. 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3 | Nodetraysize | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.1 | Nodemp | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.1.1 | Scalarbrmpsize | read-write | mandatory | MP Tray paper size -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 8… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.2 | Nodecassette | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.2.1 | Scalarbrtray1size | read-write | mandatory | Tray1 paper size -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.3 | Nodecassette2 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.3.1 | Scalarbrtray2size | read-write | mandatory | Tray2 paper size -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.4 | Nodecassette3 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.4.1 | Scalarbrtray3size | read-write | mandatory | Tray3 paper size -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.5 | Nodecassette4 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.3.3.5.1 | Scalarbrtray4size | read-write | mandatory | Tray4 paper size -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.6 | Nodeeconomy | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.6.5 | Scalarbrret | read-write | mandatory | HRC mode. 1:Off 2:Bright 3:Medium 4:Dark |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.4.1.6.7 | Scalarbreconomode | read-write | mandatory | Toner Save mode. 100:Off 0:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5 | Nodebrorg | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1 | Nodeprintersetup | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1 | Nodegeneral | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.1 | ScalarbrPrtGeneralEmulationTimeout | read-write | mandatory | Emulation Timeout. 1- 99(sec) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.2 | ScalarbrPrtGeneralFeeder | read-write | mandatory | Default Feeder mode. 0:Auto 1:MP Tray 2:Tray1 3:Tray2 4:Tray3 5:Tray4 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.3 | ScalarbrPrtGeneralPowerSave | read-write | mandatory | Power Save mode. 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.4 | ScalarbrPrtGeneralBuzzer | read-write | mandatory | Buzzer. 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.5 | ScalarbrPrtGeneralColor | read-write | mandatory | Default Color mode 1:Monochrome 2:Color 3:Auto |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.6 | ScalarbrPrtGeneralDuplex | read-write | mandatory | Duplex mode 1:Off(Simplex) 2:On(Duplex) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.1.7 | ScalarbrPrtGeneralBinding | read-write | mandatory | Binding type 3:Short Edge 2:Long Edge |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2 | Nodeadvanced | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.1 | ScalarbrPrtAdvancedPriority | read-write | mandatory | FX/XL Priority. 1:IBM XL 2:EPSON FX |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.2 | ScalarbrPrtAdvancedUseMPTrayFirst | read-write | mandatory | MP Tray First 1:No 2:Yes |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.3 | ScalarbrPrtAdvancedMPTrayFeed | read-write | mandatory | MP Tray feed mode. 1:Single 2:Continuous |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.4 | ScalarbrPrtAdvancedXOffset | read-write | mandatory | X Offset. -500 to +500 pixel(600dpi) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.5 | ScalarbrPrtAdvancedYOffset | read-write | mandatory | Y Offset. -500 to +500 pixel(600dpi) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.6 | ScalarbrPrtAdvancedImageCompression | read-write | mandatory | Image Compression mode. 0:Auto 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.7 | Nodeautoff | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.7.1 | ScalarbrPrtAdvancedAutoFormFeed | read-write | mandatory | Auto Formfeed mode. 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.7.2 | ScalarbrPrtAdvancedAutoTimeout | read-write | mandatory | Auto Formfeed timeout. 1-99 (sec) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.8 | ScalarbrPrtAdvancedFFSuppress | read-write | mandatory | FF Suppress mode. 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.9 | ScalarbrPrtAdvancedTonerLowPrint | read-write | mandatory | Print mode on Toner Low. 1:Stop 2:Continue |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.10 | ScalarbrPrtAdvancedPrintDensity | read-write | mandatory | Print Density. 1-15 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.11 | ScalarbrPrtAdvancedInputBuffer | read-write | mandatory | Input Buffer size. 1-15 blocks |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.12 | ScalarbrPrtAdvancedLanguage | read-write | mandatory | 1:ENGLISH 2:DANISH 3:DUTCH 4:FINNISH 5:FRENCH 6:GERMAN 7:ITALIAN 8:NORWEGIAN 9:PORTUGUESE 10:SWEDISH 11:SPANISH 12:TURKISH 13:POLISH 14:JAPANESE 15:RUSSIAN 16:… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.13 | ScalarbrSecurePrintRAMSizeMax | read-only | mandatory | The Max of Secure print RAM Size |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.14 | ScalarbrSecurePrintRAMSize | read-write | mandatory | Secure print RAM Size |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.15 | ScalarbrPrtAdvancedJamRecovery | read-write | mandatory | Jam recovery setting |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.16 | ScalarbrPrtAdvancedSleepIndication | read-write | mandatory | By enabling the Dimmed option, the status LED is dimmed while the printer is in sleep mode. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.17 | ScalarbrPrtAdvancedDestination | read-write | mandatory | Destination |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.18 | ScalarbrPrtAdvancedLowerLCD | read-write | mandatory | Lower LCD |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.19 | ScalarbrPrtAdvancedAutoOnline | read-write | mandatory | Auto Online |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.20 | ScalarbrPrtAdvancedButtonRepeat | read-write | mandatory | Button Repeat. 0.1-2.0 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.21 | ScalarbrPrtAdvancedMessageScroll | read-write | mandatory | Message Scroll. 1-10 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.22 | Nodebuzzer | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.22.1 | ScalarbrPrtAdvancedErrorBuzzer | read-write | mandatory | Error Buzzer |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.22.2 | ScalarbrPrtAdvancedPanelBuzzer | read-write | mandatory | Panel Buzzer |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.22.3 | ScalarbrPrtAdvancedBuzzerVolume | read-write | mandatory | Buzzer Volume |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.23 | ScalarbrPrtAdvancedLCDDensity | read-write | mandatory | LCDDensity |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.51 | NodesmallPaperSize | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.51.1 | ScalarbrSmallPaperSizeMP | read-write | mandatory | MP Tray Small Paper size. 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDG… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.51.2 | ScalarbrSmallPaperSize1 | read-write | mandatory | Tray1 Small Paper size. 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.51.3 | ScalarbrSmallPaperSize2 | read-write | mandatory | Tray2 Small Paper size. 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.51.4 | ScalarbrSmallPaperSize3 | read-write | mandatory | Tray3 Small Paper size. 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.51.5 | ScalarbrSmallPaperSize4 | read-write | mandatory | Tray4 Small Paper size. 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 890:LEDGER… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52 | NodetrayPriority | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52.1 | ScalarbrPrtAdvancedTrayPriority | read-write | mandatory | The value of brTrayPriorityIndex corresponding to the default setting. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52.2 | ScalarbrTrayPriorityCount | read-only | mandatory | Maximum number of TrayPriority INDEX. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52.3 | TablebrTrayPriorityTable | not-accessible | mandatory | This table represents TrayPriority setting. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52.3.1 | RowbrTrayPriorityEntry | not-accessible | mandatory | A row in the TrayPriority table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52.3.1.1 | ColumnbrTrayPriorityIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.52.3.1.2 | ColumnbrTrayPriorityMember | read-only | mandatory | The TrayPriority member data. Format: valulen(1byte), value(valulen byte) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53 | NodecarbonCopy | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.1 | ScalarbrCarbonCopyMode | read-write | mandatory | Carbon Copy mode setting. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.2 | ScalarbrCarbonCopies | read-write | mandatory | The copies setting of Carbon Copy function. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.10 | TablebrCarbonCopyTable | not-accessible | mandatory | This table represents CarbonCopy setting. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.10.1 | RowbrCarbonCopyEntry | not-accessible | mandatory | A row in the CarbonCopy table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.10.1.1 | ColumnbrCarbonCopyIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.10.1.2 | ColumnbrCarbonCopyTray | read-write | mandatory | Copy Tray setting. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.10.1.3 | ColumnbrCarbonCopyMacro | read-write | mandatory | Carbon Copy Macro Setting |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.53.10.1.4 | ColumnbrCarbonCopyMacroID | read-write | mandatory | Carbon Copy Macro ID Setting |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.54 | NodemediaFix | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.54.1 | ScalarbrMediaFixTray1 | read-write | mandatory | Media Fix setting for tray1. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.54.2 | ScalarbrMediaFixTray2 | read-write | mandatory | Media Fix setting for tray2. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.54.3 | ScalarbrMediaFixTray3 | read-write | mandatory | Media Fix setting for tray3. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.54.4 | ScalarbrMediaFixTray4 | read-write | mandatory | Media Fix setting for tray4. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.54.10 | ScalarbrMediaFixMP | read-write | mandatory | Media Fix setting for MPtray. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60 | Nodedirectprint | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.1 | ScalarbrDirectPrintPaperSize | read-write | mandatory | Default Paper size. -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 … |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.2 | ScalarbrDirectPrintMediaType | read-write | mandatory | Default Media type. 0:Regular 1:Thick paper 2:Thicker paper 3:Transparency 4:Thin paper 5:Bond paper 6:ENVELOPES 7:ENV. THICK 8:ENV. THIN 9:RECYCLED 10:HAGAKI … |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.3 | ScalarbrDirectPrintMultipulPage | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.4 | ScalarbrDirectPrintOrientation | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.5 | ScalarbrDirectPrintCollate | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.6 | ScalarbrDirectPrintOutputColor | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.7 | ScalarbrDirectPrintPrintQuality | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.8 | ScalarbrDirectPrintPdfOption | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.9 | ScalarbrDirectPrintSetting | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.60.10 | ScalarbrDirectPrintPdfThumbnailType | read-write | mandatory | PDF Thumbnail Type 1:AlternativeImage 2:ReductionImage |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61 | Nodepictbridge | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61.1 | ScalarbrPictBridgePaperSize | read-write | mandatory | Default Paper size. -1:No Casette 1:Executive 2:Letter 3:Legal 24:A6 25:A5 26:A4 27:A3(ISO) 45:B5(JIS) 46:B4(JIS) 80:Monarch 81:COM10 90:DL 91:C5 99:B6 100:B5 … |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61.2 | ScalarbrPictBridgeOrientation | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61.3 | ScalarbrPictBridgeDateTime | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61.4 | ScalarbrPictBridgeFileName | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61.5 | ScalarbrPictBridgePrintQuality | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.61.6 | ScalarbrPictBridgePrintSetting | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62 | Nodecolorcorrection | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.1 | ScalarbrColorCalibration | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.2 | ScalarbrColorCalibrationReset | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.3 | ScalarbrAutoRegistRegistrate | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.4 | ScalarbrAutoRegistSetInterval | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.5 | ScalarbrRegistrationPrintChart | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.6 | ScalarbrRegistrationXMagentaLeft | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.7 | ScalarbrRegistrationXMagentaRight | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.8 | ScalarbrRegistrationXCyanLeft | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.9 | ScalarbrRegistrationXCyanRight | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.10 | ScalarbrRegistrationXYellowLeft | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.11 | ScalarbrRegistrationXYellowRight | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.12 | ScalarbrRegistrationYMagenta | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.13 | ScalarbrRegistrationYCyan | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.62.14 | ScalarbrRegistrationYYellow | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63 | Nodefunclock | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.1 | ScalarbrFuncLockSettingInit | read-write | mandatory | Init Function Lock Setting. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.2 | ScalarbrFuncLockAdminPassword | read-write | mandatory | Get or Set the administrator password of Function Lock. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.3 | ScalarbrFuncLock | read-write | mandatory | Get or Set the status of Function Lock. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.4 | ScalarbrFuncLockPublicFuncCount | read-only | mandatory | Return the number of functions to be locked on the public mode. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.5 | TablebrFuncLockPublicTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.5.1 | RowbrFuncLockPublicEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.5.1.1 | ColumnbrFuncLockPublicFuncIndex | read-only | mandatory | Return the index value of functions to be locked on the public mode. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.5.1.2 | ColumnbrFuncLockPublicFuncMember | read-only | mandatory | Return the member of functions to be locked on the public mode. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.5.1.3 | ColumnbrFuncLockPublicFuncSupported | read-only | mandatory | Return the status of availableness of functions to be locked on the public mode. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.5.1.4 | ColumnbrFuncLockPublicFuncEnable | read-write | mandatory | Get of Set the status of functions on the public mode. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.6 | ScalarbrFuncLockUserCount | read-only | mandatory | Return the number of users to be locked on function lock. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.7 | TablebrFuncLockUserTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.7.1 | RowbrFuncLockUserEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.7.1.1 | ColumnbrFuncLockUserIndex | read-only | mandatory | Return the index value of users to be locked on function lock. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.7.1.2 | ColumnbrFuncLockUserName | read-write | mandatory | Get or Set the user name of function lock. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.7.1.3 | ColumnbrFuncLockUserPassword | read-write | mandatory | Get or Set the user password of function lock. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.8 | ScalarbrFuncLockUserFuncCount | read-only | mandatory | Return the number of users to be locked on the function lock. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.9 | TablebrFuncLockUserFuncTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.9.1 | RowbrFuncLockUserFuncEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.9.1.1 | ColumnbrFuncLockUserFuncIndex | read-only | mandatory | Return the index value of users to be locked on user mode. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.9.1.2 | ColumnbrFuncLockUserFuncMember | read-only | mandatory | Return the function numbers to be locked on user mode. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.9.1.3 | ColumnbrFuncLockUserFuncSupported | read-only | mandatory | Return the availableness of function to be locked on user mode. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.9.1.4 | ColumnbrFuncLockUserFuncEnable | read-write | mandatory | Get or Set the lock status on the user mode. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.10 | ScalarbrFuncLockSetting | read-write | mandatory | Write the all information of function lock. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.20 | ScalarbrFuncLockUserPrintPageCounterReset | read-write | mandatory | Reset all user's counter of Color/Mono print page. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.21 | ScalarbrFuncLockPublicPrintLimitEnable | read-write | mandatory | This MIB represents Enable/Disable of print limit setting for public user. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.22 | ScalarbrFuncLockPublicPrintPageMax | read-write | mandatory | The Maximum of print limited for public user. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.23 | ScalarbrFuncLockPublicPrintPageCountMono | read-only | mandatory | The counter of monochrome print page. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.24 | ScalarbrFuncLockPublicPrintPageCountColor | read-only | mandatory | The counter of color print page for public user. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25 | TablebrFuncLockUserPrintPageTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1 | RowbrFuncLockUserPrintPageEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.1 | ColumnbrFuncLockUserPrintPageIndex | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.2 | ColumnbrFuncLockUserPrintPageLimitEnable | read-write | mandatory | The Maximum of Print Page setting for user. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.3 | ColumnbrFuncLockUserPrintPageCountMono | read-only | mandatory | The Counter of Monochrome Print Page for user. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.4 | ColumnbrFuncLockUserPrintPageCountColor | read-only | mandatory | The counter of color print page for user. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.5 | ColumnbrFuncLockUserPrintPageMax | read-write | mandatory | The Maximum of print limited for user. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.6 | ColumnbrFuncLockUserPrintPageCountMonoLast | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.25.1.7 | ColumnbrFuncLockUserPrintPageCountColorLast | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.26 | ScalarbrFuncLockPcLoginNameAuthEnable | read-write | mandatory | This MIB represents Enable/Disable of PC Login Authentication setting. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.27 | ScalarbrFuncLockPcLoginNameAuthCount | read-only | mandatory | The number of PC Login Name. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.28 | TablebrFuncLockPcLoginNameTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.28.1 | RowbrFuncLockPcLoginNameEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.28.1.1 | ColumnbrFuncLockPcLoginNameAuthIndex | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.28.1.2 | ColumnbrFuncLockPcLoginName | read-write | mandatory | The PC Login Name. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.28.1.3 | ColumnbrFuncLockPcLoginNameAuthID | read-write | mandatory | PC Login ID for PC Login name. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.29 | ScalarbrFuncLockPublicPrintPageCountMonoLast | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.30 | ScalarbrFuncLockPublicPrintPageCountColorLast | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.31 | Nodeautocountreset | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.31.1 | ScalarbrFuncLockAutoCountResetFrequency | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.31.2 | ScalarbrFuncLockAutoCountResetTime | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.31.3 | ScalarbrFuncLockAutoCountResetWeek | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.2.63.31.4 | ScalarbrFuncLockAutoCountResetDate | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3 | Nodemail | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.1 | ScalarbrPrtMailbox | read-write | mandatory | Mailbox Installed of not |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.2 | TablebrPrtMailboxProtectTable | not-accessible | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.2.1 | RowbrPrtMailboxProtectEntry | not-accessible | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.2.1.1 | ColumnbrPrtMailboxProtectIndex | read-write | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.2.1.2 | ColumnbrPrtMailboxProtect | read-write | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.3 | TablebrPrtAvoidMailboxFullTable | not-accessible | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.3.1 | RowbrPrtAvoidMailboxFullEntry | not-accessible | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.3.1.1 | ColumnbrPrtAvoidMailboxFullIndex | read-write | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.3.1.2 | ColumnbrPrtAvoidMailboxFull | read-write | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.4 | ScalarbrPrtMailboxOutbin | read-write | mandatory | Outbin |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.5 | ScalarbrPrtMailboxProtectGroup | read-write | mandatory | Mailbox Protect |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.3.6 | ScalarbrPrtAvoidMailboxFullGroup | read-write | mandatory | Avoid Mailbox Full |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.4 | Nodefinisher | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.4.1 | ScalarbrPrtFinisher | read-only | mandatory | Finisher type 0:no finisher 1:FS5050 2:FS5100 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.5 | Nodecatch-tray | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.1.5.1 | ScalarbrPrtCatchTray | read-only | mandatory | catch tray Installed or not |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2 | Nodepagesetup | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1 | Nodepcl | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.1 | Nodemargin-p | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.1.1 | ScalarbrPagePCLLeftMargin | read-write | mandatory | PCL LeftMargin 1270N :0-145 2400Ce :0-176 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.1.2 | ScalarbrPagePCLRightMargin | read-write | mandatory | PCL RightMargin 1270N :10-155 2400Ce :10-186 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.1.3 | ScalarbrPagePCLTopMargin | read-write | mandatory | PCL TopMargin 0:0 33:0.33 50:0.5 100:1.0 150:1.5 200:2.0 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.1.4 | ScalarbrPagePCLBottomMargin | read-write | mandatory | PCL BottomMargin 0:0 33:0.33 50:0.5 100:1.0 150:1.5 200:2.0 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.1.5 | ScalarbrPagePCLLines | read-write | mandatory | PCL Form Line 5-128 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.2 | Nodeauto-p | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.2.1 | ScalarbrPagePCLAutoLF | read-write | mandatory | PCL AutoLF 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.2.2 | ScalarbrPagePCLAutoCR | read-write | mandatory | PCL AutoCR 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.2.3 | ScalarbrPagePCLAutoWrap | read-write | mandatory | PCL AutoWrap 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.1.2.4 | ScalarbrPagePCLAutoSkip | read-write | mandatory | PCL AutoSkip 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.2 | Nodeps | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.2.1 | ScalarbrPagePSPrintPSError | read-write | mandatory | PrintPSError 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.2.2 | ScalarbrPagePSKeepPCLFonts | read-write | mandatory | KeepPCLFonts 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.2.3 | ScalarbrPagePSCAPTsetting | read-write | mandatory | PS CAPT setting 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3 | Nodegl | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.1 | Nodepen1 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.1.1 | ScalarbrPageGLPen1Size | read-write | mandatory | GL PenSize 1-16 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.1.2 | ScalarbrPageGLPen1GrayLevel | read-write | mandatory | GLPen GrayLevel 0:15% 1:30% 2:45% 3:75% 4:90% 5:100% |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.2 | Nodepen2 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.2.1 | ScalarbrPageGLPen2Size | read-write | mandatory | GL PenSize 1-16 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.2.2 | ScalarbrPageGLPen2GrayLevel | read-write | mandatory | GLPen GrayLevel 0:15% 1:30% 2:45% 3:75% 4:90% 5:100% |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.3 | Nodepen3 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.3.1 | ScalarbrPageGLPen3Size | read-write | mandatory | GL PenSize 1-16 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.3.2 | ScalarbrPageGLPen3GrayLevel | read-write | mandatory | GLPen GrayLevel 0:15% 1:30% 2:45% 3:75% 4:90% 5:100% |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.4 | Nodepen4 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.4.1 | ScalarbrPageGLPen4Size | read-write | mandatory | GL PenSize 1-16 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.4.2 | ScalarbrPageGLPen4GrayLevel | read-write | mandatory | GLPen GrayLevel 0:15% 1:30% 2:45% 3:75% 4:90% 5:100% |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.5 | Nodepen5 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.5.1 | ScalarbrPageGLPen5Size | read-write | mandatory | GL PenSize 1-16 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.5.2 | ScalarbrPageGLPen5GrayLevel | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.6 | Nodepen6 | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.6.1 | ScalarbrPageGLPen6Size | read-write | mandatory | GL PenSize 1-16 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.3.6.2 | ScalarbrPageGLPen6GrayLevel | read-write | mandatory | GLPen GrayLevel 0:15% 1:30% 2:45% 3:75% 4:90% 5:100% |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4 | Nodeepson | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.1 | Nodemargin-e | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.1.1 | ScalarbrPageEPSONLeftMargin | read-write | mandatory | EPSON LeftMargin 1270N :0-145 2400Ce :0-176 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.1.2 | ScalarbrPageEPSONRightMargin | read-write | mandatory | EPSON RightMargin 1270N :10-155 2400Ce :10-186 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.1.3 | ScalarbrPageEPSONTopMargin | read-write | mandatory | EPSON TopMargin 0:0 33:0.33 50:0.5 100:1.0 150:1.5 200:2.0 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.1.4 | ScalarbrPageEPSONBottomMargin | read-write | mandatory | EPSON BottomMargin 0:0 33:0.33 50:0.5 100:1.0 150:1.5 200:2.0 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.1.5 | ScalarbrPageEPSONLines | read-write | mandatory | EPSON Form Line 5-128 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.2 | Nodeauto-e | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.2.1 | ScalarbrPageEPSONAutoLF | read-write | mandatory | EPSON AutoLF 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.4.2.5 | ScalarbrPageEPSONAutoMask | read-write | mandatory | EPSON AutoMask 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5 | Nodeibm | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.1 | Nodemargin-i | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.1.1 | ScalarbrPageIBMLeftMargin | read-write | mandatory | IBM LeftMargin 1270N :0-145 2400Ce :0-176 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.1.2 | ScalarbrPageIBMRightMargin | read-write | mandatory | IBM LeftMargin 1270N :10-155 2400Ce :10-186 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.1.3 | ScalarbrPageIBMTopMargin | read-write | mandatory | IBM BottomMargin 0:0 33:0.33 50:0.5 100:1.0 150:1.5 200:2.0 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.1.4 | ScalarbrPageIBMBottomMargin | read-write | mandatory | IBM BottomMargin 0:0 33:0.33 50:0.5 100:1.0 150:1.5 200:2.0 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.1.5 | ScalarbrPageIBMLines | read-write | mandatory | IBM Form Line 5-128 |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.2 | Nodeauto-i | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.2.1 | ScalarbrPageIBMAutoLF | read-write | mandatory | IBM AutoLF 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.2.2 | ScalarbrPageIBMAutoCR | read-write | mandatory | IBM AutoCR 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.2.5.2.5 | ScalarbrPageIBMAutoMask | read-write | mandatory | IBM AutoMask 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.3 | Nodefontsetup | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.3.1 | ScalarbrFontName | read-write | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.3.2 | ScalarbrFontPointSize | read-write | mandatory | unused(400-99975) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.3.3 | ScalarbrFontPitch | read-write | mandatory | unused(44-9999) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.3.4 | ScalarbrFontSymbolSet | read-write | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4 | Nodecontrolpanel | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.1 | Nodereset | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.1.1 | ScalarbrPanelResetUser | read-write | mandatory | User Reset |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.1.2 | ScalarbrPanelResetFactory | read-write | mandatory | Factory Reset |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.2 | Nodetest | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.2.1 | ScalarbrPanelTestConfiguration | read-write | mandatory | Print Config page |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.2.2 | ScalarbrPanelTestFontList | read-write | mandatory | Print Fonts list |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.2.3 | ScalarbrPanelTestTestPage | read-write | mandatory | Print Test page |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.2.4 | ScalarbrPanelTestDemoPage | read-write | mandatory | Print Demo page 0:Enable Print Demo page 1:Disable Print Demo page |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.3 | Nodepanellock | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.3.1 | ScalarbrPanelLockPasswd | read-write | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.3.2 | ScalarbrPanelLock | read-only | mandatory | The state of panel lock |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.3.3 | ScalarbrPanelLockOn | read-write | mandatory | Panel Lock by setting a password. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.3.4 | ScalarbrPanelLockOff | read-write | mandatory | Panel Lock is canceled by inputting a password.. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4 | Nodekey | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.1 | ScalarbrPanelKeyOnline | read-write | mandatory | Press Online Key |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.2 | ScalarbrPanelKeyFormFeed | read-write | mandatory | Press FormFeed Key |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.3 | ScalarbrPanelKeyContinue | read-write | mandatory | Press Countinue Key |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.4 | ScalarbrPanelKeyMode | read-write | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.5 | ScalarbrPanelKeyGo | read-write | mandatory | Press Go Key |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.6 | ScalarbrPanelKeyJobCancel | read-write | mandatory | Press JobCancel Key |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.7 | ScalarbrPanelKeyReprint | read-write | mandatory | Press Reprint Key |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.4.8 | ScalarbrPanelKeySecure | read-write | mandatory | Press SecurePrint Key |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5 | Nodepanelinfo | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.1 | ScalarbrLCDMode1 | read-only | mandatory | LCD Display Mode. 1:fix 2:blink 3:scroll |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.2 | ScalarbrLCDString1 | read-only | mandatory | LCD Display String of first line. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.3 | ScalarbrLCDMode2 | read-only | mandatory | LCD Display Mode. 1:fix 2:blink 3:scroll |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.4 | ScalarbrLCDString2 | read-only | mandatory | LCD Display String of second line. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.5 | ScalarbrLCDString16fix | read-only | mandatory | LCD Display String of 16fix. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.6 | ScalarbrBackLightColor | read-only | mandatory | LCD Display Mode. 0:Off 1:Green 2:Orange 3:Red |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.7 | ScalarbrLCDMode3 | read-only | mandatory | LCD Display Mode. 1:fix 2:blink 3:scroll |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.8 | ScalarbrLCDString3 | read-only | mandatory | LCD Display String of first line. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.9 | ScalarbrLCDMode4 | read-only | mandatory | LCD Display Mode. 1:fix 2:blink 3:scroll |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.10 | ScalarbrLCDString4 | read-only | mandatory | LCD Display String of first line. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.11 | ScalarbrLCDMode5 | read-only | mandatory | LCD Display Mode. 1:fix 2:blink 3:scroll |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.12 | ScalarbrLCDString5 | read-only | mandatory | LCD Display String of first line. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.4.5.13 | ScalarbrLCDContrast | read-write | mandatory | This value adjusts the contrast of the LCD Display. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5 | Nodeprinterinfomation | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.1 | ScalarbrInfoSerialNumber | read-only | mandatory | Serial number of printer |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.2 | ScalarbrInfoType | read-only | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.3 | Nodeversion | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.3.1 | ScalarbrInfoUpperMIBVer | read-only | mandatory | unused (upper digit of the MIB version) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.3.2 | ScalarbrInfoLowerMIBVer | read-only | mandatory | unused (lower digit of the MIB version) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.4 | ScalarbrInfoStatus | read-only | mandatory | Status message ID |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.5 | ScalarbrInfoNetVerUpStatus | read-only | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.6 | ScalarbrInfoPrinterUStatus | read-only | mandatory | Status ID |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.7 | ScalarbrInfoPConSupported | read-only | mandatory | BRPCon support 0:not supported 1:supported |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.8 | ScalarbrInfoMaintenance | read-only | mandatory | Maintenance info. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.9 | ScalarbrInfoModelNumber | read-only | mandatory | Printer Model ID 4:2400Ce 5:3400CN 6:3260 8:2460 9:2600cn 11:3450cn 13:am 14:zlhe 15:zl2 16:jigen 17:aml 18:l4c 19: ALL 20: AL LED 21: AL LCD 22: HL-4040CN 23:… |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.10 | ScalarbrInfoCounter | read-only | mandatory | Page counter |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.11 | ScalarbrInfoNextCare | read-only | mandatory | Remaining life info. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.12 | ScalarbrInfoHDDSlot1 | read-only | mandatory | Card Slot1 status 1:complete 2:IO error 3:memory error 4:not found 5:no device 6:no file(format) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.13 | ScalarbrInfoHDDSlot2 | read-only | mandatory | Card Slot2 status 1:complete 2:IO error 3:memory error 4:not found 5:no device 6:no file(format) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.14 | ScalarbrInfoHDDInternal | read-only | mandatory | Internal HDD info. 1:complete 2:IO error 3:memory error 4:not found 5:no device 6:no file(format) |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.15 | ScalarbrInfoHDDSize | read-only | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.16 | ScalarbrInfoSolutionsCenterURL | read-only | mandatory | Brother Solutions Center's URL |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.17 | ScalarbrInfoDeviceRomVersion | read-only | mandatory | The device rom version |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.18 | ScalarbrInfoCoverage | read-only | mandatory | Coverage info. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.19 | ScalarbrInfoEstimatedPagesRemaining | read-only | mandatory | Estimated pages remaining info. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.20 | ScalarbrInfoReplaceCount | read-only | mandatory | Replace count info. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.21 | ScalarbrInfoJamCount | read-only | mandatory | Jam count info. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.22 | ScalarbrInfoJamCountClear | read-write | mandatory | Jam count Clear. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.23 | ScalarbrInfoReplaceTime | read-only | mandatory | Replace count time info. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.24 | ScalarbrInfoDeviceSubRomVersion | read-only | mandatory | The PCL/PS ROM Version. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.25 | ScalarbrInfoAlertVersion | read-only | mandatory | It indicates the version that prtAlertLocation is implemented correctly. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.26 | ScalarbrInfoBlackPrint | read-only | mandatory | It indicates black only print enable/disable info 0: disable 1: enable |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51 | NodeerrorHistory | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.1 | ScalarbrErrorHistoryCount | read-only | mandatory | Maximum number of Error History. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.2 | TablebrErrorHistoryTable | not-accessible | mandatory | This table represents Error History. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.2.1 | RowbrErrorHistoryEntry | not-accessible | mandatory | A row in the ErrorHistory table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.2.1.1 | ColumnbrErrorHistoryIndex | read-only | mandatory | A unique value for the error history. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.2.1.2 | ColumnbrErrorHistoryDescription | read-only | mandatory | The ErrorHistory Description. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.3 | ScalarbrErrorHistoryAllClear | read-write | mandatory | All clear Error History. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.11 | ScalarbrCommunicationErrorHistoryCount | read-only | mandatory | Maximum number of Communication Error History. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.12 | TablebrCommunicationErrorHistoryTable | not-accessible | mandatory | This table represents Communication Error History. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.12.1 | RowbrCommunicationErrorHistoryEntry | not-accessible | mandatory | A row in the Communication ErrorHistory table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.12.1.1 | ColumnbrCommunicationErrorHistoryIndex | read-only | mandatory | A unique value for the Communication error history. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.51.12.1.2 | ColumnbrCommunicationErrorHistoryDescription | read-only | mandatory | The Communication Error History Description. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52 | NodeprintPages | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.1 | TablebrPrintPagesTable | not-accessible | mandatory | This table represents Print Pages. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.1.1 | RowbrPrintPagesEntry | not-accessible | mandatory | A row in the PrintPages table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.1.1.1 | ColumnbrPrintPagesIndex | read-only | mandatory | A unique value for the print pages. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.1.1.2 | ColumnbrPrintPagesPaperSize | read-only | mandatory | The paper size of print pages. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.1.1.3 | ColumnbrPrintPages | read-only | mandatory | The count of Print pages. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.11 | TablebrPrintPagesMediaPlaceTable | not-accessible | mandatory | This table represents Print Pages of Media Place. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.11.1 | RowbrPrintPagesMediaPlaceEntry | not-accessible | mandatory | A row in the PrintPages Media Place table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.11.1.1 | ColumnbrPrintPagesMediaPlaceIndex | read-only | mandatory | A unique value for the print pages of media place. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.11.1.2 | ColumnbrPrintPagesMediaPlaceType | read-only | mandatory | The place of media. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.11.1.3 | ColumnbrPrintPagesMediaPlaceCounter | read-only | mandatory | The count of Print pages of media place. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.21 | TablebrPrintPagesFuncTable | not-accessible | mandatory | This table represents Print Pages of each function. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.21.1 | RowbrPrintPagesFuncEntry | not-accessible | mandatory | A row in the PrintPages Func table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.21.1.1 | ColumnbrPrintPagesFuncIndex | read-only | mandatory | A unique value for the print pages of each function. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.21.1.2 | ColumnbrPrintPagesFuncType | read-only | mandatory | The kind of function. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.21.1.3 | ColumnbrPrintPagesFuncCounter | read-only | mandatory | The count of Print pages of the function. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.31 | TablebrPrintPagesPaperTypeTable | not-accessible | mandatory | This table represents Print Pages of Paper Type. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.31.1 | RowbrPrintPagesPaperTypeEntry | not-accessible | mandatory | A row in the PrintPages Paper Type table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.31.1.1 | ColumnbrPrintPagesPaperTypeIndex | read-only | mandatory | A unique value for the print pages of paper type. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.31.1.2 | ColumnbrPrintPagesPaperTypeType | read-only | mandatory | The type of paper. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.52.31.1.3 | ColumnbrPrintPagesPaperTypeCounter | read-only | mandatory | The count of Print pages of paper type. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53 | Nodecapability | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.1 | Nodecopies | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.1.1 | ScalarbrCapabilityCopiesMax | read-only | mandatory | The maximum value of copies |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.1.2 | ScalarbrCapabilityCopiesMin | read-only | mandatory | The minimum value of copies |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.2 | Nodeorientation | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.2.1 | ScalarbrCapabilityOrientationCount | read-only | mandatory | The number of support of orientation |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.2.2 | TablebrCapabilityOrientationTable | not-accessible | mandatory | This table represents capability of orientation. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.2.2.1 | RowbrCapabilityOrientationEntry | not-accessible | mandatory | A row in the capability of orientation table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.2.2.1.1 | ColumnbrCapabilityOrientationIndex | read-only | mandatory | A unique value for the capability of orientation. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.2.2.1.2 | ColumnbrCapabilityOrientationName | read-only | mandatory | The name of orientation currently supported. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.3 | Nodepaper | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.3.1 | ScalarbrCapabilityPaperCount | read-only | mandatory | The number of kinds of the paper currently supported |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.3.2 | TablebrCapabilityPaperTable | not-accessible | mandatory | This table represents capability of paper. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.3.2.1 | RowbrCapabilityPaperEntry | not-accessible | mandatory | A row in the capability of paper table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.3.2.1.1 | ColumnbrCapabilityPaperIndex | read-only | mandatory | A unique value for the capability of paper. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.3.2.1.2 | ColumnbrCapabilityPaperName | read-only | mandatory | The name of paper currently supported. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.4 | Nodemediatype | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.4.1 | ScalarbrCapabilityMediatypeCount | read-only | mandatory | The number of kinds of the mediatype currently supported |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.4.2 | TablebrCapabilityMediatypeTable | not-accessible | mandatory | This table represents capability of mediatype. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.4.2.1 | RowbrCapabilityMediatypeEntry | not-accessible | mandatory | A row in the capability of mediatype table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.4.2.1.1 | ColumnbrCapabilityMediatypeIndex | read-only | mandatory | A unique value for the capability of mediatype. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.4.2.1.2 | ColumnbrCapabilityMediatypeName | read-only | mandatory | The name of mediatype currently supported. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.5 | Noderesolution | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.5.1 | ScalarbrCapabilityResolutionCount | read-only | mandatory | The number of kinds of the resolution currently supported |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.5.2 | TablebrCapabilityResolutionTable | not-accessible | mandatory | This table represents capability of resolution. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.5.2.1 | RowbrCapabilityResolutionEntry | not-accessible | mandatory | A row in the capability of resolution table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.5.2.1.1 | ColumnbrCapabilityResolutionIndex | read-only | mandatory | A unique value for the capability of resolution. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.53.5.2.1.2 | ColumnbrCapabilityResolution | read-only | mandatory | The value of resolution currently supported. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54 | Nodecountinfo | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1 | Nodepfkit | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1.1 | ScalarbrPfKitIndexCount | read-only | mandatory | Maximum number of PF kit. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1.2 | TablebrPfKitTable | not-accessible | mandatory | This table represents PF kit. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1.2.1 | RowbrPfKitEntry | not-accessible | mandatory | A row in the PfKit table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1.2.1.1 | ColumnbrPfKitIndex | read-only | mandatory | A unique value for the PF kit. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1.2.1.2 | ColumnbrPfKitType | read-only | mandatory | The PF kit ID. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.1.2.1.3 | ColumnbrPfKitCount | read-only | mandatory | Counter of the PF kit. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2 | Nodescancount | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2.1 | ScalarbrScanCountIndexCount | read-only | mandatory | Maximum number of Scan place. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2.2 | TablebrScanCountTable | not-accessible | mandatory | This table represents scan count. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2.2.1 | RowbrScanCountEntry | not-accessible | mandatory | A row in the ScanCount table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2.2.1.1 | ColumnbrScanCountIndex | read-only | mandatory | A unique value for the scan count place. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2.2.1.2 | ColumnbrScanCountType | read-only | mandatory | The scan place ID. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.54.2.2.1.3 | ColumnbrScanCountCounter | read-only | mandatory | Counter of the scan. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.55 | Nodefirmwareupdatekeyword | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.55.1 | ScalarbrFirmwareUpdateKeywordCount | read-only | mandatory | The number of Firmware for update the device. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.55.2 | TablebrFirmwareUpdateKeywordTable | not-accessible | mandatory | The table represents the number of Firmware for Update. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.55.2.1 | RowbrFirmwareUpdateKeywordEntry | not-accessible | mandatory | A row in the FirmwareUpdateKeyword table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.55.2.1.1 | ColumnbrFirmwareUpdateKeywordIndex | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.5.55.2.1.2 | ColumnbrFirmwareUpdateKeyword | read-only | mandatory | The keyword for firemware update the device. |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.6 | Nodeprinterstatus | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.6.1 | ScalarbrStatusSleep | read-only | mandatory | Sleeping status 0:ready 1:sleep |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.7 | Nodesecret | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.7.1 | ScalarbrSecretMPRetry | read-write | mandatory | unused |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.7.2 | ScalarbrSecretReprint | read-write | mandatory | Secret Reprint mode 0:Off 111:On 222:Job |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.7.3 | ScalarbrFontSetting | read-only | mandatory | Font Setting 0:Brother Font 1:Agfa Font |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.7.4 | ScalarbrFontSwitchOn | read-write | mandatory | Switch of Agfa Font On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.7.5 | ScalarbrFontSwitchOff | read-write | mandatory | Switch of Agfa Font Off |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.8 | Nodeadminsetting | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.8.1 | Nodeclockfunction | |||
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.8.1.1 | ScalarbrClockFuncTimeStyle | read-write | mandatory | Time format 0:YMD 1:MDY 2:DMY |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.8.1.2 | ScalarbrClockFuncSummerTime | read-write | mandatory | Summer time 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.8.1.3 | ScalarbrClockFuncTimeZone | read-write | mandatory | TimeZone |
| 1.3.6.1.4.1.2435.2.3.9.4.2.1.5.8.1.4 | ScalarbrClockFuncZoneSet | read-write | mandatory | TimeZone enable 1:Off 2:On |
| 1.3.6.1.4.1.2435.2.4 | Nodeinterface | |||
| 1.3.6.1.4.1.2435.2.4.3 | NodenpCard | |||
| 1.3.6.1.4.1.2435.2.4.3.1 | NodenpSys | |||
| 1.3.6.1.4.1.2435.2.4.3.1.1 | NodenpConfig | |||
| 1.3.6.1.4.1.2435.2.4.3.1.1.1 | ScalarbrBasicSettingConfigured | read-only | mandatory | This value indicates that the basic setting is configured or not. The condition entry of this value is model dependent. |
| 1.3.6.1.4.1.2435.2.4.3.1.99 | NodeadminCapa | |||
| 1.3.6.1.4.1.2435.2.4.3.1.99.1 | ScalarbrAdminCapability | read-only | mandatory | AdminCapability |
| 1.3.6.1.4.1.2435.2.4.3.1.100 | NodeuserSetting | |||
| 1.3.6.1.4.1.2435.2.4.3.1.100.1 | ScalarbrUserPasswordVerify | read-write | mandatory | Submit the print server's user password for verification. An error will be returned if the password is incorrect. |
| 1.3.6.1.4.1.2435.2.4.3.1.100.2 | ScalarbrUserPassword | read-write | mandatory | Set the print server's user password value. |
| 1.3.6.1.4.1.2435.2.4.3.1.101 | Nodeverify | |||
| 1.3.6.1.4.1.2435.2.4.3.1.101.1 | ScalarbrpsVerifyPhysAddress | read-write | mandatory | For verify physical address. |
| 1.3.6.1.4.1.2435.2.4.3.6 | NodenpTcp | |||
| 1.3.6.1.4.1.2435.2.4.3.6.99 | Nodelpd | |||
| 1.3.6.1.4.1.2435.2.4.3.6.99.1 | Nodebanner | |||
| 1.3.6.1.4.1.2435.2.4.3.6.99.1.1 | ScalarbrLPDBannerPage | read-write | mandatory | LPR banner page 0: disabled. 1: enabled. 2: force to print. |
| 1.3.6.1.4.1.2435.2.4.3.7 | NodenpCtl | |||
| 1.3.6.1.4.1.2435.2.4.3.7.99 | NodeetherN | |||
| 1.3.6.1.4.1.2435.2.4.3.7.99.1 | NodeeNet | |||
| 1.3.6.1.4.1.2435.2.4.3.7.99.1.1 | ScalarbrENetModeSupported | read-only | mandatory | ENet Mode 0:not supported 1:supported |
| 1.3.6.1.4.1.2435.2.4.3.7.99.1.2 | ScalarbrENetMode | read-write | mandatory | ENet Mode 0:Auto 1:FD100B 2:100Base 3:FD10B 4:10BASE |
| 1.3.6.1.4.1.2435.2.4.3.13 | NodenpPort | |||
| 1.3.6.1.4.1.2435.2.4.3.13.10 | Nodefuna | |||
| 1.3.6.1.4.1.2435.2.4.3.13.10.1 | ScalarbrFindPort | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.13.10.2 | ScalarbrFindTime | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.99 | NodenpSet | |||
| 1.3.6.1.4.1.2435.2.4.3.99.1 | Nodedns | |||
| 1.3.6.1.4.1.2435.2.4.3.99.1.1 | ScalarbrDNSSupported | read-only | mandatory | DNS resolver 0:not supported 1:supported This is the obsolete MIB that is not currently used. |
| 1.3.6.1.4.1.2435.2.4.3.99.1.2 | ScalarbrPrimaryDNSIP | read-write | mandatory | Primary DNS IP Address. This is the obsolete MIB that is not currently used. |
| 1.3.6.1.4.1.2435.2.4.3.99.1.3 | ScalarbrSecondaryDNSIP | read-write | mandatory | Secondary DNS IP Address This is the obsolete MIB that is not currently used. |
| 1.3.6.1.4.1.2435.2.4.3.99.1.4 | ScalarbrDNSIPSetup | read-write | mandatory | DNS mode 1:static 2:auto |
| 1.3.6.1.4.1.2435.2.4.3.99.1.5 | ScalarbrTCPIPConnectTime | read-write | mandatory | TCP/IP connect time. |
| 1.3.6.1.4.1.2435.2.4.3.99.1.6 | ScalarbrAdvancedDNSSupported | read-only | mandatory | DNS resolver 0:not supported 1:supported |
| 1.3.6.1.4.1.2435.2.4.3.99.1.7 | ScalarbrPrimaryDNSIPAddress | read-write | mandatory | Primary DNS IP Address |
| 1.3.6.1.4.1.2435.2.4.3.99.1.8 | ScalarbrSecondaryDNSIPAddress | read-write | mandatory | Secondary DNS IP Address |
| 1.3.6.1.4.1.2435.2.4.3.99.1.9 | ScalarbrPOP3ServerName | read-write | mandatory | The FQDN name of the POP3 server. |
| 1.3.6.1.4.1.2435.2.4.3.99.1.10 | ScalarbrSMTPServerName | read-write | mandatory | The FQDN name of the SMTP server. |
| 1.3.6.1.4.1.2435.2.4.3.99.2 | Nodepushstatus | |||
| 1.3.6.1.4.1.2435.2.4.3.99.2.1 | ScalarbrPushStatusSupported | read-only | mandatory | Notification 0:not supported 1:supported |
| 1.3.6.1.4.1.2435.2.4.3.99.2.2 | Nodepriadmin | |||
| 1.3.6.1.4.1.2435.2.4.3.99.2.2.1 | ScalarbrPriMailAddress | read-write | mandatory | Primary Mail Address |
| 1.3.6.1.4.1.2435.2.4.3.99.2.2.2 | ScalarbrPriError | read-write | mandatory | Primary Error |
| 1.3.6.1.4.1.2435.2.4.3.99.2.3 | Nodesecadmin | |||
| 1.3.6.1.4.1.2435.2.4.3.99.2.3.1 | ScalarbrSecMailAddress | read-write | mandatory | Secondary Mail Address |
| 1.3.6.1.4.1.2435.2.4.3.99.2.3.2 | ScalarbrSecError | read-write | mandatory | Secondary Error |
| 1.3.6.1.4.1.2435.2.4.3.99.2.4 | ScalarbrNotificationCount | read-only | mandatory | Maximum number of Notification Method. |
| 1.3.6.1.4.1.2435.2.4.3.99.2.5 | TablebrNotificationTable | not-accessible | mandatory | This table represents Notification Method. |
| 1.3.6.1.4.1.2435.2.4.3.99.2.5.1 | RowbrNotificationEntry | not-accessible | mandatory | A row in the Notification table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.99.2.5.1.1 | ColumnbrNotificationIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.99.2.5.1.2 | ColumnbrNotificationAddress | read-write | mandatory | The Notification Address. |
| 1.3.6.1.4.1.2435.2.4.3.99.2.5.1.3 | ColumnbrNotificationStatusGroup | read-write | mandatory | The Notification Status group |
| 1.3.6.1.4.1.2435.2.4.3.99.2.5.1.4 | ColumnbrNotificationShowURLInfo | read-write | mandatory | The setting of show URL infomation at Notification mail. |
| 1.3.6.1.4.1.2435.2.4.3.99.2.5.1.5 | ColumnbrNotificationErrorRule | read-write | mandatory | The setting of sending requirements for Notification. |
| 1.3.6.1.4.1.2435.2.4.3.99.2.5.1.6 | ColumnbrNotificationRestoration | read-write | mandatory | The setting of Restoration Notification mail |
| 1.3.6.1.4.1.2435.2.4.3.99.2.6 | ScalarbrPrintersEmailaddress | read-write | mandatory | The Printers Email Address. |
| 1.3.6.1.4.1.2435.2.4.3.99.2.7 | ScalarbrNotificationVersion | read-only | mandatory | The version of Notification |
| 1.3.6.1.4.1.2435.2.4.3.99.2.8 | ScalarbrShowIPAddressInfo | read-write | mandatory | The setting of show IP address infomation at Notification mail. |
| 1.3.6.1.4.1.2435.2.4.3.99.2.50 | TablebrNotificationRuleTable | not-accessible | mandatory | This table represents Notification Method. |
| 1.3.6.1.4.1.2435.2.4.3.99.2.50.1 | RowbrNotificationRuleEntry | not-accessible | mandatory | A row in the Notification rule table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.99.2.50.1.1 | ColumnbrNotificationRuleIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.99.2.50.1.2 | ColumnbrNotificationStatusID | read-write | mandatory | The Notification Status group ID |
| 1.3.6.1.4.1.2435.2.4.3.99.2.50.1.3 | ColumnbrNotificationMainRule | read-write | mandatory | The main rule of Notification setting. |
| 1.3.6.1.4.1.2435.2.4.3.99.2.50.1.4 | ColumnbrNotificationRuleValue | read-write | mandatory | The value of Notification setting. |
| 1.3.6.1.4.1.2435.2.4.3.99.3 | Nodepjl | |||
| 1.3.6.1.4.1.2435.2.4.3.99.3.1 | Nodepjlinfo | |||
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.1 | TablebrPJLInfoOptionsTable | not-accessible | mandatory | This table represents PJLInfoOptions. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.1.1 | RowbrPJLInfoOptionsEntry | not-accessible | mandatory | A row in the PJLInfoOptions table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.1.1.1 | ColumnbrPJLInfoOptionsIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.1.1.2 | ColumnbrPJLInfoOptions | read-only | mandatory | The PJLInfoOptions. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.2 | TablebrPJLInfoIntrayconfigTable | not-accessible | mandatory | This table represents PJLInfoIntrayconfig. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.2.1 | RowbrPJLInfoIntrayconfigEntry | not-accessible | mandatory | A row in the PJLInfoIntrayconfig table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.2.1.1 | ColumnbrPJLInfoIntrayconfigIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.2.1.2 | ColumnbrPJLInfoIntrayconfig | read-only | mandatory | The PJLInfoIntrayconfig. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.3 | TablebrPJLInfoOuttrayconfigTable | not-accessible | mandatory | This table represents PJLInfoOuttrayconfig. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.3.1 | RowbrPJLInfoOuttrayconfigEntry | not-accessible | mandatory | A row in the PJLInfoOuttrayconfig table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.3.1.1 | ColumnbrPJLInfoOuttrayconfigIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.3.1.2 | ColumnbrPJLInfoOuttrayconfig | read-only | mandatory | The PJLInfoOuttrayconfig. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.4 | TablebrPJLInfoDXconfigTable | not-accessible | mandatory | This table represents PJLInfoDXconfig. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.4.1 | RowbrPJLInfoDXconfigEntry | not-accessible | mandatory | A row in the PJLInfoDXconfig table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.4.1.1 | ColumnbrPJLInfoDXconfigIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.4.1.2 | ColumnbrPJLInfoDXconfig | read-only | mandatory | The PJLInfoDXconfig. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.5 | TablebrPJLInfoStorageconfigTable | not-accessible | mandatory | This table represents PJLInfoStorageconfig. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.5.1 | RowbrPJLInfoStorageconfigEntry | not-accessible | mandatory | A row in the PJLInfoStorageconfig table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.5.1.1 | ColumnbrPJLInfoStorageconfigIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.5.1.2 | ColumnbrPJLInfoStorageconfig | read-only | mandatory | The PJLInfoStorageconfig. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.6 | TablebrPJLInfoFirmwareUpdateconfigTable | not-accessible | mandatory | This table represents PJLInfoFirmwareUpdateconfig. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.6.1 | RowbrPJLInfoFirmwareUpdateconfigEntry | not-accessible | mandatory | A row in the PJLInfoFirmwareUpdateconfig table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.6.1.1 | ColumnbrPJLInfoFirmwareUpdateconfigIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.99.3.1.6.1.2 | ColumnbrPJLInfoFirmwareUpdateconfig | read-only | mandatory | The PJLInfoFirmwareUpdateconfig. |
| 1.3.6.1.4.1.2435.2.4.3.99.4 | NodeeMailReports | |||
| 1.3.6.1.4.1.2435.2.4.3.99.4.1 | ScalarbrEmailReportsSupported | read-only | mandatory | E-mail reports 0:not supported 1:supported |
| 1.3.6.1.4.1.2435.2.4.3.99.4.2 | ScalarbrEmailReportsCount | read-only | mandatory | The number of Administrator for E-mail reports. |
| 1.3.6.1.4.1.2435.2.4.3.99.4.11 | TablebrEmailReportsTable | not-accessible | mandatory | This table represents E-mail reports. |
| 1.3.6.1.4.1.2435.2.4.3.99.4.11.1 | RowbrEmailReportsEntry | not-accessible | mandatory | A row in the BrEmailReportsEntry table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.1 | ColumnbrEmailReportsIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.2 | ColumnbrEmailReportsAddress | read-write | mandatory | The E-mail address of Administrator for E-mail reports. |
| 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.3 | ColumnbrEmailReportsFrequency | read-write | mandatory | The frequency of sending E-mail reports. |
| 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.4 | ColumnbrEmailReportsTime | read-write | mandatory | The time setting for E-mail reports. |
| 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.5 | ColumnbrEmailReportsWeek | read-write | mandatory | The setting of day of the week for E-mail reports. |
| 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.6 | ColumnbrEmailReportsDate | read-write | mandatory | The setting of day for E-mail reports when real time clock exists. |
| 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.7 | ColumnbrEmailReportsSendReportNow | read-write | mandatory | The setting of Send Report Now function for E-mail reports. |
| 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.8 | ColumnbrEmailReportsSendReportatPowerOn | read-write | mandatory | The setting of Send Report at PowerOn for E-mail reports. |
| 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.9 | ColumnbrEmailReportsNoRTCFrequency | read-write | mandatory | The setting of day for E-mail reports when real time clock does not exists. |
| 1.3.6.1.4.1.2435.2.4.3.99.4.11.1.10 | ColumnbrEmailReportsReportFormat | read-write | mandatory | The setting of ReportFormat for E-mail reports. |
| 1.3.6.1.4.1.2435.2.4.3.100 | Nodewireless | |||
| 1.3.6.1.4.1.2435.2.4.3.100.1 | NodewlInfo | |||
| 1.3.6.1.4.1.2435.2.4.3.100.1.1 | NodewlCapability | |||
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.1 | ScalarbrpsWLanDot11Supported | read-only | mandatory | Flags per bit. 802.11a bit1=1 802.11b bit2=1 802.11g bit3=1 |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.2 | ScalarbrpsWLanAvailableChannel | read-only | mandatory | The available channel list. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.3 | ScalarbrpsWLanCapabilityEncryptModeCount | read-only | mandatory | index |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.4 | TablebrpsWLanCapabilityEncryptModeTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.4.1 | RowbrpsWLanCapabilityEncryptModeEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.4.1.1 | ColumnbrpsWLanCapabilityEncryptModeIndex | read-only | mandatory | index |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.4.1.2 | ColumnbrpsWLanCapabilityEncryptModeType | read-only | mandatory | Encrypt Mode Type |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.4.1.3 | ColumnbrpsWLanCapabilityEncryptModeDescription | read-only | mandatory | Encrypt Mode description |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.4.1.4 | ColumnbrpsWLanCapabilityEncryptModeSupported | read-only | mandatory | 0: Not Supported 1: Supported |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.5 | ScalarbrpsWLanCapabilityAuthModeCount | read-only | mandatory | index |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.6 | TablebrpsWLanCapabilityAuthModeTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.6.1 | RowbrpsWLanCapabilityAuthModeEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.6.1.1 | ColumnbrpsWLanCapabilitAuthModeIndex | read-only | mandatory | index |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.6.1.2 | ColumnbrpsWLanCapabilityAuthModeType | read-only | mandatory | Auth Mode Type |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.6.1.3 | ColumnbrpsWLanCapabilityAuthModeDescription | read-only | mandatory | Auth Mode description |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.6.1.4 | ColumnbrpsWLanCapabilityAuthModeSupported | read-only | mandatory | 0: Not Supported 1: Supported |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.7 | ScalarbrpsWLanCapabilityAuthEAPCount | read-only | mandatory | index |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.8 | TablebrpsWLanCapabilityAuthEAPTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1 | RowbrpsWLanCapabilityAuthEAPEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1.1 | ColumnbrpsWLanCapabilityAuthEAPIndex | read-only | mandatory | index |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1.2 | ColumnbrpsWLanCapabilityAuthEAPType | read-only | mandatory | Auth EAP Type |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1.3 | ColumnbrpsWLanCapabilityAuthEAPDescription | read-only | mandatory | Auth EAP description |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1.4 | ColumnbrpsWLanCapabilityAuthEAPSupported | read-only | mandatory | 0: Not Supported 1: Supported |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1.5 | ColumnbrpsWLanCapabilityAuthEAPSupportAuthentication | read-only | mandatory | put supported authentication protocol as bit. 1bit:802.1X 2bit:WPA 3bit:WPA2 4bit:CCKM |
| 1.3.6.1.4.1.2435.2.4.3.100.1.1.8.1.6 | ColumnbrpsWLanCapabilityAuthEAPSupportEncryption | read-only | mandatory | put supported encryption as bit. 1bit:WEP 2bit:CKIP 3bit:TKIP 4bit:AES |
| 1.3.6.1.4.1.2435.2.4.3.100.1.2 | NodewlGeneralInfo | |||
| 1.3.6.1.4.1.2435.2.4.3.100.1.2.1 | ScalarbrpsWLanDestination | read-only | mandatory | The destination of this NIC. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.2.2 | ScalarbrpsWLanTransmitLevel | read-only | mandatory | The level of the transmitting power. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.2.3 | ScalarbrpsPit3WLanTestStatus | read-only | mandatory | The test status of pit3 for WLAN. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11 | NodewlNetSearch | |||
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.1 | ScalarbrpsWLanNetSearchSupported | read-only | mandatory | 0 indicates the Wireless network serch function is not supported. 1 indicates the Wireless network serch function is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.2 | ScalarbrpsAvailableWLanScan | read-write | mandatory | Read: unsupported(1), supported(2) Set: <Format>= <1:Start | 2:Start w/ option>[;<sWLanName>;<sWLanCommMode>[;<sWLanChannel>]] |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.3 | ScalarbrpsAvailableWLanScanWaitTime | read-only | mandatory | Scan Wait Time |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.10 | ScalarbrpsAvailableWLanCount | read-only | mandatory | Available wireless LAN count. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.11 | TablebrpsAvailableWLanTable | not-accessible | mandatory | This table represents Available Wireless LAN Info. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1 | RowbrpsAvailableWLanEntry | not-accessible | mandatory | A row in the brpsAvailableWLanTable table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.1 | ColumnbrpsAvailableWLanIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.2 | ColumnbrpsAvailableWLanName | read-only | mandatory | The available wireless LAN name. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.3 | ColumnbrpsAvailableWLanMode | read-only | mandatory | The available wireless LAN mode. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.4 | ColumnbrpsAvailableWLanCommMode | read-only | mandatory | The available wireless LAN communication mode. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.5 | ColumnbrpsAvailableWLanChannel | read-only | mandatory | The available wireless LAN channel. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.6 | ColumnbrpsAvailableWLanPowerLevel | read-only | mandatory | The available wireless LAN power level. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.7 | ColumnbrpsAvailableWLanAuthMode | read-only | mandatory | The available wireless LAN authentication mode. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.11.11.1.8 | ColumnbrpsAvailableWLanEncryptMode | read-only | mandatory | The available wireless LAN encryption mode. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.12 | NodewlAOSS | |||
| 1.3.6.1.4.1.2435.2.4.3.100.1.12.1 | ScalarbrpsWLanAOSSSupported | read-only | mandatory | 0 indicates AOSS is not supported. 1 indicates AOSS is supported. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.12.2 | ScalarbrpsWLanAOSSIsRunnning | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.100.1.13 | NodewlSES | |||
| 1.3.6.1.4.1.2435.2.4.3.100.1.13.1 | ScalarbrpsWLanSESSupported | read-only | mandatory | 0 indicates SES is not supported. 1 indicates SES is supported. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.14 | NodewlWPS | |||
| 1.3.6.1.4.1.2435.2.4.3.100.1.14.1 | ScalarbrpsWLanWPSSupported | read-only | mandatory | 0 indicates WPS is not supported. 1 indicates WPS is supported. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.14.2 | ScalarbrpsWLanWPSResult | read-only | mandatory | 0 indicates WPS is successful. 1 indicates WPS is not successful. -1 indicates WPS is being set up. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.15 | NodewlSimpleWizard | |||
| 1.3.6.1.4.1.2435.2.4.3.100.1.15.1 | ScalarbrWlanSimpleWizardSupported | read-only | mandatory | WLAN Simple Wizard support information. 0 indicates Simple Wizard is not supported. 1 indicates Simple Wizard is supported. |
| 1.3.6.1.4.1.2435.2.4.3.100.1.15.2 | ScalarbrWlanSimpleWizardPassword | read-write | mandatory | Simple Wizard Password. Max size 64 |
| 1.3.6.1.4.1.2435.2.4.3.100.11 | NodewlSetup | |||
| 1.3.6.1.4.1.2435.2.4.3.100.11.1 | NodewlGeneral | |||
| 1.3.6.1.4.1.2435.2.4.3.100.11.1.1 | ScalarbrpsWLanAPSetupMode | read-only | mandatory | AP setup mode status. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.1.2 | ScalarbrpsWLanMode | read-write | mandatory | Wireless LAN mode. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.1.3 | ScalarbrpsWLanName | read-write | mandatory | The SSID setting. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.1.4 | ScalarbrpsWLanCommMode | read-write | mandatory | Wireless LAN communication mode. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.1.5 | ScalarbrpsWLanChannel | read-write | mandatory | Wireless LAN channel setting. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.5 | NodewlAdvanced | |||
| 1.3.6.1.4.1.2435.2.4.3.100.11.5.1 | ScalarbrpsWLanCtsMode | read-write | mandatory | Wireless LAN CTS mode setting. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.5.2 | ScalarbrpsWLanCtsRate | read-write | mandatory | Wireless LAN CTS rate setting. However, the unit is 1/10. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.5.3 | ScalarbrpsWLanCtsType | read-write | mandatory | Wireless LAN CTS type setting. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.5.4 | ScalarbrpsWLanRtsCtsThreshold | read-write | mandatory | Wireless LAN RTS/CTS threshold setting. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.5.5 | ScalarbrpsWLanLengthThreshold | read-write | mandatory | Wireless LAN length threshold setting. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.5.6 | ScalarbrpsWLanDataRetry | read-write | mandatory | Wireless LAN DATA retyr setting. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.5.7 | ScalarbrpsWLanTransmitPowerSetting | read-write | mandatory | Wireless LAN transmit power setting. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.5.8 | ScalarbrpsWLanDeviceType | read-write | mandatory | Wireless LAN operation mode setting. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11 | NodewlAssociate | |||
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.1 | ScalarbrpsWLanEncryptMode | read-write | mandatory | Wireless LAN encrypt mode. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.11 | ScalarbrpsWLanAuthMode | read-write | mandatory | Wireless LAN authenticate mode. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.12 | ScalarbrpsWLanAuthEAP | read-write | mandatory | Wireless LAN authenticate EAP. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.13 | ScalarbrpsWLanAuthUserID | read-write | mandatory | Wireless LAN authenticate user ID. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.14 | ScalarbrpsWLanAuthUserPass | read-write | mandatory | Wireless LAN authenticate user password. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.21 | ScalarbrpsWLanAssociate | read-write | mandatory | Wireless LAN associate. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.22 | ScalarbrpsWLanAssociateTestResult | read-only | mandatory | Wireless LAN associate test result. 0 indicates cleared. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.23 | ScalarbrpsWLanAssociateResult | read-only | mandatory | Wireless LAN associate result. 0 indicates cleared. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.24 | ScalarbrpsWLanAssociateTestSupported | read-only | mandatory | 0 indicates the Wireless network Associate Test function is not supported. 1 indicates the Wireless network Associate Test function is implemented by the firmw… |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.101 | NodewlWEP | |||
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.1 | ScalarbrpsWLanWepKeyDefaultIndex | read-write | mandatory | The value of brpsWLanWepKeyIndex corresponding to the default setting. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.11 | TablebrpsWLanWepKeyTable | not-accessible | mandatory | This table represents WEP KEY Info. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.11.1 | RowbrpsWLanWepKeyEntry | not-accessible | mandatory | A row in the brpsWLanWepKeyTable table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.11.1.1 | ColumnbrpsWLanWepKeyIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.11.1.2 | ColumnbrpsWLanWepKeySize | read-write | mandatory | The WEP KEY size. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.11.1.3 | ColumnbrpsWLanWepKeyType | read-write | mandatory | The WEP KEY type. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.101.11.1.4 | ColumnbrpsWLanWepKey | read-write | mandatory | The WEP KEY. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.102 | NodewlWPA | |||
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.102.1 | ScalarbrpsWLanNetworkKey | read-write | mandatory | The WPA-PSK. |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.103 | NodewlTKIP | |||
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.103.1 | ScalarbrpsWLanTKIPChangeInterval | read-write | mandatory | TKIP Interval (s) |
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.104 | NodewlLEAP | |||
| 1.3.6.1.4.1.2435.2.4.3.100.11.11.104.1 | ScalarbrpsWLanLEAPTimeout | read-write | mandatory | Leap timeout (s) |
| 1.3.6.1.4.1.2435.2.4.3.100.21 | NodewlStatus | |||
| 1.3.6.1.4.1.2435.2.4.3.100.21.1 | NodewlGeneralStatus | |||
| 1.3.6.1.4.1.2435.2.4.3.100.21.1.1 | ScalarbrpsWLanOperatingMode | read-only | mandatory | The mode which is actually operating. off(0), dot11a(1), dot11b(2), dot11g(3) |
| 1.3.6.1.4.1.2435.2.4.3.100.21.1.2 | ScalarbrpsWLanRSSLevel | read-only | mandatory | Wireless LAN RSS Level. |
| 1.3.6.1.4.1.2435.2.4.3.100.21.1.3 | ScalarbrpsWLanCommSpeed | read-only | mandatory | Wireless LAN communication speed. However, the unit is 1/10. |
| 1.3.6.1.4.1.2435.2.4.3.100.21.1.4 | ScalarbrpsWLanOperatingChannel | read-only | mandatory | Wireless LAN operating channel. |
| 1.3.6.1.4.1.2435.2.4.3.100.21.1.5 | ScalarbrpsWLanOperatingName | read-only | mandatory | Wireless LAN operating SSID Name. |
| 1.3.6.1.4.1.2435.2.4.3.100.21.1.6 | ScalarbrpsWLanOperatingCommMode | read-only | mandatory | Wireless LAN operating communication mode. off(0), infrastructure(1), ad-Hoc-WiFi(2), ad-Hoc(3) |
| 1.3.6.1.4.1.2435.2.4.3.100.21.1.7 | ScalarbrpsWLanOperatingEncryptMode | read-only | mandatory | Wireless LAN operating encrypt mode. off(0), none(1), wep(2), tkip(3), aes(4), ckip(5) |
| 1.3.6.1.4.1.2435.2.4.3.100.21.1.8 | ScalarbrpsWLanOperatingAuthMode | read-only | mandatory | Wireless LAN operating authenticate mode. off(0), openSystem(1), sharedKey(2), wpa-psk(3), wpa-none(4), wpa(5), wpa2(6), leap(7), eapfast-none(8), eapfast-msch… |
| 1.3.6.1.4.1.2435.2.4.3.100.21.1.9 | ScalarbrpsWLanOperatingWepKeyDefaultIndex | read-only | mandatory | Wireless LAN operating WepKeyDefaultIndex. |
| 1.3.6.1.4.1.2435.2.4.3.1240 | NodebrnetConfig | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.1 | Nodebrconfig | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.1.1 | ScalarbrpsNodeName | read-write | mandatory | The node name of this print server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.2 | ScalarbrpsSerialNumber | read-only | mandatory | The serial number of this print server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.3 | ScalarbrpsHardwareType | read-only | mandatory | Hardware type of the print server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.4 | ScalarbrpsMainRevision | read-only | mandatory | Revision level of the Print Server firmware suitable for display. This object may be read but not written. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.5 | ScalarbrpsBootRevision | read-only | mandatory | Revision level of the boot firmware (if applicable) suitable for display. This object may be read but not written. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.6 | ScalarbrpsPasswordVerify | read-write | mandatory | Submit the print server's password for verification. An error will be returned if the password is incorrect. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.7 | ScalarbrpsPassword | read-write | mandatory | Set the print server's password value. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.8 | ScalarbrpsMIBVersion | read-only | mandatory | Revision level of the private MIB implemented by the device. For example: 1.0 This object may be read but not written. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.9 | ScalarbrpsOEMString | read-only | mandatory | OEM string setting for the print server. This object may be read but not written. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.10 | ScalarbrpsMIBMajor | read-only | mandatory | MIB major version number. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.11 | ScalarbrpsMIBMinor | read-only | mandatory | MIB minor version number. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.12 | ScalarbrpsServerDescription | read-write | mandatory | Product name of print server. For example: NC-3100h This object may be read but not written. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.13 | ScalarbrpsEnetMode | read-write | mandatory | Ethernet type. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.14 | ScalarbrpsFlashROMSize | read-only | mandatory | Flash ROM Size of print server (MBytes). |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.15 | ScalarbrpsSNMPGetCommunity | read-only | mandatory | SNMP Get Community Name. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.16 | ScalarbrpsSNMPJetAdmin | read-only | mandatory | 0 indicates the JetAdmin compatibility mode is not enabled. 1 indicates JetAdmin compatibility mode is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.17 | ScalarbrpsSNMPSetCommunity1 | read-only | mandatory | SNMP Set Community Name #1. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.18 | ScalarbrpsSNMPSetCommunity2 | read-only | mandatory | SNMP Set Community Name #2. |
| 1.3.6.1.4.1.2435.2.4.3.1240.1.200 | ScalarbrSupportedInfo | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.1240.2 | Nodebrcontrol | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.2.1 | ScalarbrpsTestPage | read-write | mandatory | Setting any value generates a test page on all ports. |
| 1.3.6.1.4.1.2435.2.4.3.1240.2.2 | ScalarbrpsSetDefault | read-write | mandatory | Setting the value 5AA5h (23205) resets all parameters to their factory default value. |
| 1.3.6.1.4.1.2435.2.4.3.1240.2.3 | ScalarbrpsReset | read-write | mandatory | Setting the value 55AAh (21930) causes the print server to perform a soft reset. |
| 1.3.6.1.4.1.2435.2.4.3.1240.2.4 | ScalarbrpsProtectModeEnable | read-only | mandatory | 0 indicates the protect mode is not enabled. 1 indicates protect mode is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.1240.2.5 | ScalarbrpsProtectPassword | read-only | mandatory | protect password. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3 | Nodebrport | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.3.1 | ScalarbrpsPortCount | read-only | mandatory | Number of ports on this print server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2 | TablebrpsPortInfoTable | not-accessible | mandatory | This table represents the attributes of a port. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1 | RowbrpsPortInfoEntry | not-accessible | mandatory | A row in the port table. Rows cannot be created or deleted via direct SNMP operations. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.1 | ColumnbrpsPortIndex | read-only | mandatory | The port number. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.2 | ColumnbrpsPortName | read-write | mandatory | The port name. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.3 | ColumnbrpsPortType | read-only | mandatory | Type of port. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.4 | ColumnbrpsPortStatus | read-only | mandatory | The port status as a 32 bit integer. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.5 | ColumnbrpsPortStatusString | read-only | mandatory | The port status description. Reflects the printer's front panel display on internal print server interfaces. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.6 | ColumnbrpsPortProtocol | read-only | mandatory | Protocol currently printing on this port. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.7 | ColumnbrpsPortQueueSize | read-only | mandatory | Number of protocols waiting to print on this port. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.8 | ColumnbrpsPortDescriptionString | read-only | mandatory | The port description. Reflects the device ID of the printer connected to the port. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.9 | ColumnbrpsPortInfoString | read-only | mandatory | The port status information. More information about the port status. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.10 | ColumnbrpsPortHTTPExtensions | read-only | mandatory | 0 indicates the printer on this port does not support HTTP, 1 indicates that the printer does support HTTP. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.11 | ColumnbrpsPortSNMPExtensions | read-only | mandatory | 0 indicates the printer on this port does not support SNMP, 1 indicates that the printer does support SNMP. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.12 | ColumnbrpsPortAttribute | read-write | mandatory | Port attribute. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.13 | ColumnbrpsPortBinaryMode | read-write | mandatory | Port binary mode. |
| 1.3.6.1.4.1.2435.2.4.3.1240.3.2.1.14 | ColumnbrpsPortInhibitDatagramSupport | read-write | mandatory | 0 indicates the inhibit datagram is not supported. 1 indicates the inhibit datagram is supported. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4 | Nodebrservice | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.4.1 | ScalarbrpsServiceCount | read-only | mandatory | Number of services on this print server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2 | TablebrpsServiceInfoTable | not-accessible | mandatory | This table represents the attributes of a service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1 | RowbrpsServiceInfoEntry | not-accessible | mandatory | A row in the services table. Rows cannot be created or deleted via direct SNMP operations. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.1 | ColumnbrpsServiceIndex | read-only | mandatory | The service number. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.2 | ColumnbrpsServiceName | read-write | mandatory | The service name. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.3 | ColumnbrpsServicePort | read-write | mandatory | The port number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.4 | ColumnbrpsServiceFilter | read-write | mandatory | Filter number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.5 | ColumnbrpsServiceBOT | read-write | mandatory | Beginning of text string number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.6 | ColumnbrpsServiceEOT | read-write | mandatory | End of text string number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.7 | ColumnbrpsServiceMatch | read-write | mandatory | Match string number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.8 | ColumnbrpsServiceReplace | read-write | mandatory | Replace string number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.9 | ColumnbrpsServiceTCPPort | read-write | mandatory | TCP Port number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.10 | ColumnbrpsServiceNDSTree | read-write | mandatory | The NDS Tree. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.11 | ColumnbrpsServiceNDSContext | read-write | mandatory | The NDS Context in Unicode. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.12 | ColumnbrpsServiceVines | read-write | mandatory | The Vines StreetTalk name for this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.13 | ColumnbrpsServiceObsolete | read-write | mandatory | Obsolete parameter that is no longer used |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.14 | ColumnbrpsServiceNetwareServerCount | read-write | mandatory | The number of Netware servers enabled on this service. Modifying the value will truncate the server list to the specified number of servers. If the value set i… |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.15 | ColumnbrpsServiceReceiveOnly | read-write | mandatory | When enabled, the service will only receive data, any printer responses will be discarded. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.16 | ColumnbrpsServiceTCPQueued | read-write | mandatory | When enabled, the raw TCP connections to the port will be queued while waiting for the port to become available |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.17 | ColumnbrpsServiceProtocolLAT | read-write | mandatory | When enabled, the LAT protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.18 | ColumnbrpsServiceProtocolTCPIP | read-write | mandatory | When enabled, the TCP/IP protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.19 | ColumnbrpsServiceProtocolNetware | read-write | mandatory | When enabled, the Netware protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.20 | ColumnbrpsServiceProtocolAppleTalk | read-write | mandatory | When enabled, the AppleTalk protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.21 | ColumnbrpsServiceProtocolBanyan | read-write | mandatory | When enabled, the Banyan protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.22 | ColumnbrpsServiceProtocolDLC | read-write | mandatory | When enabled, the DLC protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.23 | ColumnbrpsServiceProtocolNetBEUI | read-write | mandatory | When enabled, the NetBEUI protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.24 | ColumnbrpsServiceNetwareServerMode | read-write | mandatory | Netware mode for this service. 0 = Queue Server, 1 = Remote Printer |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.25 | ColumnbrpsServiceNetwareRemotePrinterNum | read-write | mandatory | Remote Printer Number for this service |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.26 | ColumnbrpsServiceProtocolIPP | read-write | mandatory | When enabled, the IPP protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.2.1.27 | ColumnbrpsServiceAppleTalkType | read-write | mandatory | AppleTalk type. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.3 | ScalarbrpsServiceStringLimit | read-only | mandatory | Maximum number of service strings supported by the print server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.4 | TablebrpsServiceStringInfoTable | not-accessible | mandatory | This table represents the service BOT/EOT/MATCH/REPLACE strings defined. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.4.1 | RowbrpsServiceStringInfoEntry | not-accessible | mandatory | A row in the service string table. Rows cannot be created or deleted via direct SNMP operations. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.4.1.1 | ColumnbrpsServiceStringIndex | read-only | mandatory | The string number. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.4.1.2 | ColumnbrpsServiceString | read-write | mandatory | The character string definition suitable for displaying. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.5 | ScalarbrpsServiceStringCount | read-only | mandatory | Number of service strings currently defined on the print server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.4.6 | ScalarbrpsServiceFilterCount | read-only | mandatory | Number of service filters implemented by the device. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5 | Nodebrprotocol | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.5.1 | Nodebrlat | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.5.1.1 | ScalarbrpsLATSupported | read-only | mandatory | 0 indicates the LAT protocol is not supported. 1 indicates LAT support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.1.2 | ScalarbrpsLATEnable | read-write | mandatory | 0 indicates the LAT protocol is not enabled. 1 indicates that the LAT protocol is enabled. Writing a non-zero value will enable the LAT protocol if it is suppo… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.1.3 | ScalarbrpsLATCircuitTimer | read-write | mandatory | Minimum time (in milliseconds) between transmissions to the host. The default of 10 normally provides the best performance. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.1.4 | ScalarbrpsLATKeepAliveTimer | read-write | mandatory | How often in seconds a packet is transmitted to keep a connection alive. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.1.5 | ScalarbrpsLATReceiveBufferMax | read-write | mandatory | LAT receive buffer max size. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.1.6 | ScalarbrpsLATTransmitBufferMax | read-write | mandatory | LAT transmit buffer max size. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.1.7 | ScalarbrpsLATTimeout | read-write | mandatory | LAT inactivity timeout (sec). |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.1.8 | ScalarbrpsLATGroup | read-write | mandatory | LAT group membership (mm-[nn]). |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2 | Nodebrtcpip | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.1 | ScalarbrpsTCPIPSupported | read-only | mandatory | 0 indicates the TCP/IP protocol is not supported. 1 indicates TCP/IP support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.2 | ScalarbrpsTCPIPEnable | read-write | mandatory | 0 indicates the TCP/IP protocol is not enabled. 1 indicates that the TCP/IP protocol is enabled. Writing a non-zero value will enable the TCP/IP protocol if it… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.3 | ScalarbrpsTCPIPAddress | read-write | mandatory | IP Address assigned to the print server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.4 | ScalarbrpsTCPIPSubnetMask | read-write | mandatory | Subnet mask assigned to the print server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.5 | ScalarbrpsTCPIPGateway | read-write | mandatory | Gateway/Router address assigned to the print server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.6 | ScalarbrpsTCPIPMethod | read-write | mandatory | Method used to determine the IP Address. AUTO tries all protocols. STATIC uses the configured address. DHCP, BOOTP, and RARP use only that protocol. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.7 | ScalarbrpsTCPIPTimeout | read-write | mandatory | Timeout used for LPD connections. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.8 | ScalarbrpsTCPIPBootTries | read-write | mandatory | Number of attempts to use BOOTP, RARP, and DHCP. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.9 | ScalarbrpsTCPIPMaxWindow | read-write | mandatory | Maximum window size for TCP connections. Due to resource limitations setting the window to values greater than 10240 is not recommended. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.10 | ScalarbrpsTCPIPRARPNoSubnet | read-write | mandatory | If enabled, do not set the subnet mask based on the RARP response. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.11 | ScalarbrpsTCPIPRARPNoGateway | read-write | mandatory | If enabled, do not set the gateway/router address based on the RARP response. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.12 | ScalarbrpsTCPIPUpdate | read-write | mandatory | Hardware MAC address to be updated. This value is write only. Will read back as zeros. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.13 | ScalarbrpsTCPIPBanner | read-write | mandatory | 0 indicates the LPR banner print is not enabled. 1 indicates that the LPR banner print is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.14 | ScalarbrpsTCPIPFastTimeoutEnable | read-write | mandatory | 0 indicates the fast timeout is not enabled. 1 indicates that the fast timeout is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.15 | ScalarbrpsTCPIPLPRRetryEnable | read-write | mandatory | 0 indicates the LPR print retry is not enabled. 1 indicates that the LPR print retry is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.16 | ScalarbrpsTCPIPUseMethod | read-write | mandatory | Method type that used set up TCP/IP configuration. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.17 | ScalarbrpsTCPIPMethodServer | read-write | mandatory | If TCP/IP configuration is setted up by any protocol server, this entry indicates the IP address of the server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.18 | TablebrpsTCPIPAccessTable | not-accessible | mandatory | This table represents the list of IP address of node that has parmittion for access.Up to 16 Netware addresses can be enabled. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.18.1 | RowbrpsTCPIPAccessEntry | not-accessible | mandatory | A row in the TCP/IP access table. Rows cannot be created or deleted via direct SNMP operations. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.18.1.1 | ColumnbrpsTCPIPAccessIndex | read-only | mandatory | The TCP/IP access table's index. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.18.1.2 | ColumnbrpsTCPIPAccessNodeAddress | read-write | mandatory | IP address of node that has parmittion for access. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.18.1.3 | ColumnbrpsTCPIPAccessSubnetMask | read-write | mandatory | Subnet mask of node that has parmittion for access. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.19 | ScalarbrpsAdvancedTCPIPAccessSupported | read-only | mandatory | 0 indicates the Advanced TCP/IP Access is not supported. 1 indicates Advanced TCP/IP Access support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.20 | ScalarbrpsAdvancedTCPIPAccessEnable | read-write | mandatory | 0 indicates the Advanced TCP/IP Access is not enabled. 1 indicates that the Advanced TCP/IP Access is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.21 | ScalarbrpsAdvancedTCPIPAccessAdministratorIPAddress | read-write | mandatory | Administrator IPAddress. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.2.22 | ScalarbrpsAdvancedTCPIPAccessSetting | read-write | mandatory | 0 indicates the Advanced TCP/IP Access is reject. 1 indicates that the Advanced TCP/IP Access is Accept. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3 | Nodebrnetware | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.1 | ScalarbrpsNetwareSupported | read-only | mandatory | 0 indicates the Netware protocol is not supported. 1 indicates Netware support is implemented by the firmware. 2 indicates that Netware NEST NDS support is imp… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.2 | ScalarbrpsNetwareEnable | read-write | mandatory | 0 indicates the Netware protocol is not enabled. 1 indicates that the Netware protocol is enabled. Writing a non-zero value will enable the Netware protocol if… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.3 | ScalarbrpsNetwareFrameType | read-write | mandatory | The frame type to be used as follows: 0 = Automatic, 1 = Ethernet 802.3, 2 = Ethernet II, 3 = Ethernet 802.2, 4 = Ethernet SNAP. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.4 | ScalarbrpsNetwarePollFreq | read-write | mandatory | File server polling frequency in seconds. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.5 | ScalarbrpsNetwareAdvFreq | read-write | mandatory | Print server advertising frequency in seconds. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.6 | ScalarbrpsNetwarePassword | read-write | mandatory | The Netware login password. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.7 | ScalarbrpsNetwareRestart | read-write | mandatory | Setting any value will restart the Netware protocol. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.8 | TablebrpsNetwareServerTable | not-accessible | mandatory | This table represents the list of enabled Netware servers. Up to 16 Netware servers can be enabled. If the service is configured for remote printer mode, then … |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.8.1 | RowbrpsNetwareServerEntry | not-accessible | mandatory | A row in the Netware server table. Rows cannot be created or deleted via direct SNMP operations. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.8.1.1 | ColumnbrpsNetwareServerIndex | read-only | mandatory | The Netware server number. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.8.1.2 | ColumnbrpsNetwareServerName | read-write | mandatory | The Netware server name. Specifies a print server if the service is in remote printer mode, or a file server if the service is in queue server mode |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.9 | ScalarbrpsNetwarePasswordSet | read-only | mandatory | Returns 1 if the Netware login password is set, 0 if not set. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.10 | ScalarbrpsNDSSupported | read-only | mandatory | 0 indicates NDS is not supported. 1 indicates NDS is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.11 | ScalarbrpsNetwareEtherIINetInfo | read-only | mandatory | Ethernet II network information. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.12 | ScalarbrpsNetwareEtherIICount | read-only | mandatory | Ethernet II network counter |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.13 | ScalarbrpsNetware8022NetInfo | read-only | mandatory | IEEE 802.2 network information. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.14 | ScalarbrpsNetware8022Count | read-only | mandatory | IEEE 802.2 network counter. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.15 | ScalarbrpsNetware8023NetInfo | read-only | mandatory | IEEE 802.3 network information. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.16 | ScalarbrpsNetware8023Count | read-only | mandatory | IEEE 802.3 network information. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.17 | ScalarbrpsNetwareSNAPNetInfo | read-only | mandatory | SNAP network information. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.18 | ScalarbrpsNetwareSNAPCount | read-only | mandatory | SNAP network count. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.19 | ScalarbrpsNetwareServicingServerName | read-only | mandatory | Netware server name. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.20 | ScalarbrpsNetwareServicingQueueName | read-only | mandatory | Netware queue name. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.21 | ScalarbrpsNetwareServicingServerCount | read-only | mandatory | Number of netware servers. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.22 | ScalarbrpsNetwareServicingQueueCount | read-only | mandatory | Number of netware queues. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.3.23 | ScalarbrpsNetwarePrintJob | read-only | mandatory | Number of netware print job. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.4 | Nodebrappletalk | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.5.4.1 | ScalarbrpsAppleTalkSupported | read-only | mandatory | 0 indicates the AppleTalk protocol is not supported. 1 indicates AppleTalk support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.4.2 | ScalarbrpsAppleTalkEnable | read-write | mandatory | 0 indicates the AppleTalk protocol is not enabled. 1 indicates that the AppleTalk protocol is enabled. Writing a non-zero value will enable the AppleTalk proto… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.4.3 | ScalarbrpsAppleTalkZone | read-write | mandatory | The AppleTalk zone the print server belongs to. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.4.4 | ScalarbrpsAppleTalkPrintJob | read-only | mandatory | Counter of AppleTalk print job. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.4.5 | ScalarbrpsAppleTalkReadByte | read-only | mandatory | Counter of read bytes. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.4.6 | ScalarbrpsAppleTalkWriteByte | read-only | mandatory | Counter of write bytes. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.4.7 | ScalarbrpsAppleTalkReadError | read-only | mandatory | Counter of read error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.4.8 | ScalarbrpsAppleTalkWriteError | read-only | mandatory | Counter of write error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5 | Nodebrbanyan | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.1 | ScalarbrpsBanyanSupported | read-only | mandatory | 0 indicates the Banyan protocol is not supported. 1 indicates Banyan support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.2 | ScalarbrpsBanyanEnable | read-write | mandatory | 0 indicates the Banyan protocol is not enabled. 1 indicates that the Banyan protocol is enabled. Writing a non-zero value will enable the Banyan protocol if is… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.3 | ScalarbrpsBanyanLoginName | read-write | mandatory | The Banyan login name. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.4 | ScalarbrpsBanyanPassword | read-write | mandatory | The Banyan login password. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.5 | ScalarbrpsBanyanHopCount | read-write | mandatory | Number of hops between the print server and the Banyan file server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.6 | ScalarbrpsBanyanTimeout | read-write | mandatory | Timeout in seconds for a Banyan print job. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.7 | ScalarbrpsBanyanPasswordSet | read-only | mandatory | Returns 1 if the Banyan login password is set, 0 if not set. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.8 | ScalarbrpsBanyanIPNetworkID1 | read-only | mandatory | IP Network ID. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.9 | ScalarbrpsBanyanIPNetworkID2 | read-only | mandatory | IP Network ID. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.10 | ScalarbrpsBanyanRouter1 | read-only | mandatory | Router ID. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.11 | ScalarbrpsBanyanRouter2 | read-only | mandatory | Router ID. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.12 | ScalarbrpsBanyanIPPacket | read-only | mandatory | Counter of IP Packet. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.13 | ScalarbrpsBanyanErrorCS | read-only | mandatory | Counter of CS error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.14 | ScalarbrpsBanyanErrorPT | read-only | mandatory | Counter of PT error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.15 | ScalarbrpsBanyanErrorLE | read-only | mandatory | Counter of LE error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.16 | ScalarbrpsBanyanPrintServerStatus | read-only | mandatory | Banyan print server status. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.17 | ScalarbrpsBanyanServerAddress1 | read-only | mandatory | Banyan server address. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.18 | ScalarbrpsBanyanServerAddress2 | read-only | mandatory | Banyan server address. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.19 | ScalarbrpsBanyanIPCConnectionInformation | read-only | mandatory | IPC connection information. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.20 | ScalarbrpsBanyanIPCSequenceError | read-only | mandatory | IPC sequence error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.21 | ScalarbrpsBanyanIPCListen | read-only | mandatory | IPC listen. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.22 | ScalarbrpsBanyanSPPConnectionInformation | read-only | mandatory | SPP connection information. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.23 | ScalarbrpsBanyanSPPSequenceError | read-only | mandatory | SPP sequence error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.5.24 | ScalarbrpsBanyanSPPListen | read-only | mandatory | SPP listen. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6 | Nodebremail | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.1 | ScalarbrpsEmailSupported | read-only | mandatory | 0 indicates the POP3/SMTP email protocols are not supported. 1 indicates email support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.2 | ScalarbrpsEmailEnable | read-write | mandatory | 0 indicates the POP3/SMTP email protocols are not enabled. 1 indicates that the email protocols are enabled. Writing a non-zero value will enable the email pro… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.3 | ScalarbrpsPOP3Address | read-write | mandatory | The IP Address of the POP3 server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.4 | ScalarbrpsSMTPAddress | read-write | mandatory | The IP Address of the SMTP server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.5 | ScalarbrpsPOP3Name | read-write | mandatory | The POP3 mailbox name. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.6 | ScalarbrpsPOP3Password | read-write | mandatory | The POP3 mailbox password. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.7 | ScalarbrpsPOP3PollFreq | read-write | mandatory | The POP3 polling frequency in seconds. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.8 | ScalarbrpsPOP3Timeout | read-write | mandatory | The POP3 timeout in minutes. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.9 | ScalarbrpsPOP3PasswordSet | read-only | mandatory | Returns 1 if the POP3 password is set, 0 if not set. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.10 | ScalarbrpsPOP3TotalMessage | read-only | mandatory | Counter of POP3 message. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.11 | ScalarbrpsPOP3TotalConnect | read-only | mandatory | Counter of POP3 connect. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.12 | ScalarbrpsPOP3TotalConnectFailure | read-only | mandatory | Counter of POP3 connect error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.13 | ScalarbrpsPOP3TotalConnectionLost | read-only | mandatory | Counter of POP3 connection lost. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.14 | ScalarbrpsPOP3TotalUserFailure | read-only | mandatory | Counter of POP3 user error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.15 | ScalarbrpsPOP3TotalPasswordFailure | read-only | mandatory | Counter of POP3 pass error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.16 | ScalarbrpsPOP3TotalIOError | read-only | mandatory | Counter of POP3 I/O error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.17 | ScalarbrpsSMTPTotalMessage | read-only | mandatory | Counter of SMTP message. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.18 | ScalarbrpsSMTPTotalConnect | read-only | mandatory | Counter of SMTP connect. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.19 | ScalarbrpsSMTPTotalConnectFailure | read-only | mandatory | Counter of SMTP connect error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.20 | ScalarbrpsSMTPTotalRecvFromFailure | read-only | mandatory | Counter of SMTP recvfrom error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.21 | ScalarbrpsSMTPTotalSendToFailure | read-only | mandatory | Counter of SMTP recvfrom error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.101 | ScalarbrpsPOP3Supported | read-only | mandatory | 0 indicates the POP3 protocol is not supported. 1 indicates the POP3 protocol is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.102 | ScalarbrpsSMTPServerAuthMethod | read-write | mandatory | 0 indicates the user is not authenticated to the SMTP Server. 1 indicates the user is authenticated to the SMTP Server using SMTP-AUTH. 2 indicates the user is… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.103 | ScalarbrpsSMTPAUTHUsername | read-write | mandatory | The username of SMTP server's account. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.104 | ScalarbrpsSMTPAUTHPassword | read-write | mandatory | The password of SMTP server's account. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.105 | ScalarbrpsSMTPAUTHPasswordSet | read-only | mandatory | Returns 1 if the SMTP server login password is set, 0 if not set. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.106 | ScalarbrpsSmtpAUTHTimeout | read-write | mandatory | The SMTP-AUTH timeout in seconds. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.107 | ScalarbrpsPOPbeforeSMTPWait | read-write | mandatory | The wait time in mili seconds between POP logging in and SMTP sending. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.108 | ScalarbrpsAPOPEnable | read-write | mandatory | 0 indicates the APOP is not enabled. 1 indicates the APOP is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.150 | ScalarbrpsSMTPEnhancedAuthSupported | read-only | mandatory | Bit0 indicates 'no authentication'. Bit1 indicates 'SMTP-AUTH'. Bit2 indicates 'POP before SMTP'. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.151 | ScalarbrpsAPOPSupported | read-only | mandatory | 0 indicates the APOP is not supported. 1 indicates the APOP is supported. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.152 | ScalarbrpsEmailSendTestSupported | read-only | mandatory | 0 indicates the Email Sending Test is not supported. 1 indicates the Email Sending Test is supported. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.153 | ScalarbrpsEmailRecvTestSupported | read-only | mandatory | 0 indicates the Email Receiving Test is not supported. 1 indicates the Email Receiving Test is supported. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.154 | ScalarbrpsChangeSMTPPortSupported | read-only | mandatory | 0 indicates to change the SMTP port number is not supported. 1 indicates to change the SMTP port number is supported. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.155 | ScalarbrpsSMTPPortNumber | read-write | mandatory | The port number of connection to SMTP server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.156 | ScalarbrpsChangePOP3PortSupported | read-only | mandatory | 0 indicates to change the POP3 port number is not supported. 1 indicates to change the POP3 port number is supported. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.157 | ScalarbrpsPOP3PortNumber | read-write | mandatory | The port number of connection to POP3 server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.170 | ScalarbrpsTmpSMTPServerName | read-write | mandatory | Temporary Setting for Email Sending Test. The FQDN name of the SMTP server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.171 | ScalarbrpsTmpSMTPServerAuthMethod | read-write | mandatory | Temporary Setting for Email Sending Test. 0 indicates the user is not authenticated to the SMTP Server. 1 indicates the user is authenticated to the SMTP Serve… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.172 | ScalarbrpsTmpSMTPAUTHUsername | read-write | mandatory | Temporary Setting for Email Sending Test. The username of SMTP server's account. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.173 | ScalarbrpsTmpSMTPAUTHPassword | read-write | mandatory | Temporary Setting for Email Sending Test. The password of SMTP server's account. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.174 | ScalarbrpsTmpPOP3ServerName | read-write | mandatory | Temporary Setting for Email Sending/Receiving Test. The FQDN name of the POP3 server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.175 | ScalarbrpsTmpPOP3Name | read-write | mandatory | Temporary Setting for Email Sending/Receiving Test. The POP3 mailbox name. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.176 | ScalarbrpsTmpPOP3Password | read-write | mandatory | Temporary Setting for Email Sending/Receiving Test. The POP3 mailbox password. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.177 | ScalarbrpsTmpPrintersEmailaddress | read-write | mandatory | Temporary Setting for Email Sending Test. The Printers Email Address |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.178 | ScalarbrpsTmpAPOPEnable | read-write | mandatory | Temporary Setting for Email Sending/Receiving Test. 0 indicates the APOP is not enabled. 1 indicates the APOP is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.179 | ScalarbrpsTmpSMTPAUTHPasswordModified | read-write | mandatory | 0 indicates the SMTP server password is not modified. 1 indicates the SMTP server password is modified. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.180 | ScalarbrpsTmpPOP3PasswordModified | read-write | mandatory | 0 indicates the POP3 server password is not modified. 1 indicates the POP3 server password is modified. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.181 | ScalarbrpsTmpSMTPPortNumber | read-write | mandatory | Temporary Setting for Email Sending Test. The port number of connection to SMTP server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.182 | ScalarbrpsTmpPOP3PortNumber | read-write | mandatory | Temporary Setting for Email Sending/Receiving Test. The port number of connection to POP3 server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.200 | ScalarbrpsEmailSendTestMail | read-write | mandatory | 0 indicates the testmail is not sended at Email Sending Test. 1 indicates the testmail is sended at Email Sending Test. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.201 | ScalarbrpsEmailTestDestinationAddress | read-write | mandatory | The destination Email Address of Email Sending Test. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.210 | ScalarbrpsEmailSendTestCall | read-write | mandatory | 0 indicates the Email Sending Test is not called on. ('READY') 1 indicates the Email Sending Test is called on. ('START') 2 indicates the Email Sending Test is… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.211 | ScalarbrpsEmailRecvTestCall | read-write | mandatory | 0 indicates the Email Receiving Test is not called on. ('READY') 1 indicates the Email Receiving Test is called. ('START') 2 indicates the Email Receiving Test… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.212 | ScalarbrpsEmailSendRecvTestCall | read-write | mandatory | 0 indicates the Email Sending and Receiving Test is not called on. ('READY') 1 indicates the Email Sending and Receiving Test is called. ('START') 2 indicates … |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.220 | ScalarbrpsEmailTestResult | read-write | mandatory | This Value is divided into 15-8bit and 7-0bit. 15-8bit indicates Email Sending Test's Result. 7-0bit indicates Email Receiving Test's Result. (However, the val… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.6.221 | ScalarbrpsPOP3TotalAPOPFailure | read-only | mandatory | Counter of POP3 APOP error. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.7 | Nodebrdlc | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.5.7.1 | ScalarbrpsDLCSupported | read-only | mandatory | 0 indicates the DLC protocol is not supported. 1 indicates DLC support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.7.2 | ScalarbrpsDLCEnable | read-write | mandatory | 0 indicates the DLC protocol is not enabled. 1 indicates that the DLC protocol is enabled. Writing a non-zero value will enable the DLC protocol if is is suppo… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.7.3 | ScalarbrpsDLCPrintStatus | read-only | mandatory | DLC print status. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.7.4 | ScalarbrpsDLCLLCState | read-only | mandatory | LLC status. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.7.5 | ScalarbrpsDLCLLCConnectHost | read-only | mandatory | LLC connected host name. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.7.6 | ScalarbrpsDLCLLCLastIFrame | read-only | mandatory | LLC last valid I-frame. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.7.7 | ScalarbrpsDLCLLCRecvPacket | read-only | mandatory | Counter of LLC receive packets. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.7.8 | ScalarbrpsDLCLLCPortStatus | read-only | mandatory | Port status. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.8 | Nodebrnetbeui | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.5.8.1 | ScalarbrpsNetBEUISupported | read-only | mandatory | 0 indicates the NetBEUI protocol is not supported. 1 indicates NetBEUI support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.8.2 | ScalarbrpsNetBEUIEnable | read-write | mandatory | 0 indicates the NetBEUI protocol is not enabled. 1 indicates that the NetBEUI protocol is enabled. Writing a non-zero value will enable the NetBEUI protocol if… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.8.3 | ScalarbrpsNetBEUIDomain | read-write | mandatory | The NetBEUI domain name. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.8.4 | ScalarbrpsNetBIOSIPSupported | read-only | mandatory | 0 indicates the NetBIOS IP protocol is not supported. 1 indicates NetBIOS IP support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.8.5 | ScalarbrpsNetBIOSIPEnable | read-write | mandatory | 0 indicates the NetBIOS IP protocol is not enabled. 1 indicates that the NetBIOS IP protocol is enabled. Writing a non-zero value will enable the NetBIOS IP pr… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.8.6 | ScalarbrpsNetBIOSIPMethod | read-write | mandatory | Method used to determine the IP Address of the WINS server. AUTO tries all protocols (currently only DHCP is tried). STATIC uses the configured address. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.8.7 | ScalarbrpsNetBIOSPrimaryWINSAddr | read-write | mandatory | The IP Address of the primary WINS server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.8.8 | ScalarbrpsNetBIOSSecondaryWINSAddr | read-write | mandatory | The IP Address of the secondary WINS server. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.8.101 | ScalarbrpsNetBIOSPrintingSupported | read-only | mandatory | 0 indicates the NetBIOS IP protocol printing is not supported. 1 indicates the NetBIOS IP protocol printing is supported. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.9 | Nodebripp | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.5.9.1 | ScalarbrpsIPPSupported | read-only | mandatory | 0 indicates the IPP protocol is not supported. 1 indicates IPP support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.9.2 | ScalarbrpsIPPEnable | read-write | mandatory | 0 indicates the IPP protocol is not enabled. 1 indicates that the IPP protocol is enabled. Writing a non-zero value will enable the IPP protocol if it is suppo… |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.9.3 | ScalarbrIPPRegularPortEnable | read-write | mandatory | 0 indicates that the IPP regular port is not enabled. 1 indicates that the IPP regular port is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.9.4 | ScalarbrIPPSSLPortEnable | read-write | mandatory | 0 indicates that the IPP SSL port is not enabled. 1 indicates that the IPP SSL port is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.9.5 | ScalarbrIPPOriginalPortEnable | read-write | mandatory | 0 indicates that the IPP original port is not enableed. 1 indicates that the IPP original port is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.10 | Nodebrntsend | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.5.10.1 | ScalarbrpsNtSendSupported | read-only | mandatory | 0 indicates the NtSend protocol is not supported. 1 indicates NtSend support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.5.10.2 | ScalarbrpsNtSendEnable | read-write | mandatory | 0 indicates the NtSend protocol is not enabled. 1 indicates that the NtSend protocol is enabled. Writing a non-zero value will enable the NtSend protocol if it… |
| 1.3.6.1.4.1.2435.2.4.3.1240.6 | Nodebrfirmware | |||
| 1.3.6.1.4.1.2435.2.4.3.1240.6.1 | ScalarbrpsFirmwareIPAddress | read-write | mandatory | The IP address of the host from which to TFTP GET the firmware. |
| 1.3.6.1.4.1.2435.2.4.3.1240.6.2 | ScalarbrpsFirmwareHost | read-write | mandatory | The Netware server name from which to fetch the firmware. |
| 1.3.6.1.4.1.2435.2.4.3.1240.6.3 | ScalarbrpsFirmwareFile | read-write | mandatory | The firmware file to be reloaded. |
| 1.3.6.1.4.1.2435.2.4.3.1240.6.4 | ScalarbrpsFirmwareReload | read-write | mandatory | Setting a value of 0x5A will cause the print server to begin attempts to reload the firmware within 5 seconds. Further attempts to read or modify the configura… |
| 1.3.6.1.4.1.2435.2.4.3.1240.6.5 | ScalarbrpsFirmwareDescription | read-only | mandatory | Firmware version and date. |
| 1.3.6.1.4.1.2435.2.4.3.1240.6.6 | ScalarbrpsFirmwareXModem | read-write | mandatory | Set 1 execute XMODEM mode. |
| 1.3.6.1.4.1.2435.2.4.3.1240.6.7 | ScalarbrpsFirmwareAdvancedAddressSupported | read-only | mandatory | 0 indicates the Firmware Advanced Address is not supported. 1 indicates Firmware Advanced Address support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.1240.6.8 | ScalarbrpsFirmwareAdvancedAddress | read-write | mandatory | The address of the host from which to TFTP GET the firmware. |
| 1.3.6.1.4.1.2435.2.4.3.2435 | NodebrnetConfigOpt | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5 | Nodebroriginalprotocol | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.2 | Nodebroriginaltcpip | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.2.1 | ScalarbrLPDType | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.10 | Nodebroriginalftp | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.10.1 | ScalarbrFTPSupported | read-only | mandatory | 0 indicates the FTP protocol is not supported. 1 indicates FTP support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.10.2 | ScalarbrFTPEnable | read-write | mandatory | 0 indicates the FTP protocol is not enabled. 1 indicates that the FTP protocol is enabled. Writing a non-zero value will enable the FTP protocol if it is suppo… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.11 | Nodebroriginalupnp | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.11.1 | ScalarbrUPnPSupported | read-only | mandatory | 0 indicates the UPnP protocol is not supported. 1 indicates UPnP support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.11.2 | ScalarbrUPnPEnable | read-write | mandatory | 0 indicates the UPnP protocol is not enabled. 1 indicates that the UPnP protocol is enabled. Writing a non-zero value will enable the UPnP protocol if it is su… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.12 | Nodebroriginalapipa | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.12.1 | ScalarbrAPIPASupported | read-only | mandatory | 0 indicates the APIPA protocol is not supported. 1 indicates APIPA support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.12.2 | ScalarbrAPIPAEnable | read-write | mandatory | 0 indicates the APIPA protocol is not enabled. 1 indicates that the APIPA protocol is enabled. Writing a non-zero value will enable the APIPA protocol if it is… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.13 | Nodebroriginalmdns | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.13.1 | ScalarbrmDNSSupported | read-only | mandatory | 0 indicates the mDNS protocol is not supported. 1 indicates mDNS support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.13.2 | ScalarbrmDNSEnable | read-write | mandatory | 0 indicates the mDNS protocol is not enabled. 1 indicates that the mDNS protocol is enabled. Writing a non-zero value will enable the mDNS protocol if it is su… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.13.3 | ScalarbrmDNSPrinterName | read-write | mandatory | mDNS Service Name |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.14 | NodebroriginalLAA | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.14.1 | ScalarbrLAASupported | read-only | mandatory | This value indicate if the locally administered addressing is supported. 0: Not Supported 1: Supported |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.14.2 | ScalarbrLAAMacAddress | read-write | mandatory | A locally administered address (LAA) that replaces the factory-assigned MAC address (UAA: universally administered address). If this setting is all-zero addres… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.15 | NodebroriginalIPv6 | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.15.1 | ScalarbrIPv6Supported | read-only | mandatory | 0 indicates the IPv6 protocol is not supported. 1 indicates IPv6 support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.15.2 | ScalarbrIPv6Enable | read-write | mandatory | 0 indicates the IPv6 protocol is not enabled. 1 indicates that the IPv6 protocol is enabled. Writing a non-zero value will enable the IPv6 protocol if it is su… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.15.3 | ScalarbrIPv6Priority | read-write | mandatory | 0 indicates the IPv6 protocol is low priority. 1 indicates that the IPv6 protocol is high priority. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.16 | Nodebroriginaltelnet | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.16.1 | ScalarbrtelnetSupported | read-only | mandatory | 0 indicates the telnet protocol is not supported. 1 indicates telnet support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.16.2 | ScalarbrtelnetEnable | read-write | mandatory | 0 indicates the telnet protocol is not enabled. 1 indicates that the telnet protocol is enabled. Writing a non-zero value will enable the telnet protocol if it… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.17 | NodebroriginalEWS | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.17.1 | ScalarbrEWSSupported | read-only | mandatory | 0 indicates the EWS protocol is not supported. 1 indicates EWS support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.17.2 | ScalarbrEWSEnable | read-write | mandatory | 0 indicates the EWS protocol is not enabled. 1 indicates that the EWS protocol is enabled. Writing a non-zero value will enable the EWS protocol if it is suppo… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.17.3 | ScalarbrEWSRegularPortEnable | read-write | mandatory | 0 indicates that the EWS regular port is not enabled. 1 indicates that the EWS regular port is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.17.4 | ScalarbrEWSSSLPortEnable | read-write | mandatory | 0 indicates that the EWS SSL port is not enabled. 1 indicates that the EWS SSL port is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.18 | NodebroriginalSNMP | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.18.1 | ScalarbrSNMPSupported | read-only | mandatory | 0 indicates the SNMP protocol is not supported. 1 indicates SNMP support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.18.2 | ScalarbrSNMPEnable | read-write | mandatory | 0 indicates the SNMP protocol is not enabled. 1 indicates that the SNMP protocol is enabled. Writing a non-zero value will enable the SNMP protocol if it is su… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.18.10 | ScalarbrSNMPV3Supported | read-only | mandatory | 0 indicates SNMPv3 is not supported. 1 indicates SNMPv3 is supported. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.18.11 | ScalarbrSNMPCommMode | read-write | mandatory | 1 indicates v1/v2c read-write access is enable. 2 indicates v3 read-write access is enable. 3 indicates v1/v2c read-only access and v3 read-write access is ena… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.18.12 | ScalarbrSNMPV3UserName | read-write | mandatory | The username of SNMPv3. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.18.13 | ScalarbrSNMPV3KeyType | read-write | mandatory | 1 indicates that the key type of SNMPv3 is ASCII. 2 indicates that the key type of SNMPv3 is HEX |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.18.14 | ScalarbrSNMPV3AuthKey | read-write | mandatory | The authentication key of SNMPv3. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.18.15 | ScalarbrSNMPV3AuthPassword | read-write | mandatory | The authentication password of SNMPv3. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.18.16 | ScalarbrSNMPV3PrivKey | read-write | mandatory | The privacy key of SNMPv3. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.18.17 | ScalarbrSNMPV3PrivPassword | read-write | mandatory | The privacy password of SNMPv3. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.18.18 | ScalarbrSNMPV3ContextName | read-write | mandatory | The contextname of SNMPv3. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19 | Nodebroriginalldap | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.1 | ScalarbrLdapSupported | read-only | mandatory | 0 indicates the LDAP client is not supported. 1 indicates the LDAP client is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.2 | ScalarbrLdapEnable | read-write | mandatory | 0 indicates the LDAP client is not enabled. 1 indicates that the LDAP client is enabled. Writing a non-zero value will enable the Ldap if it is supported by th… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.3 | ScalarbrLdapTimeout | read-write | mandatory | timeout value (sec) for LDAP server. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.4 | ScalarbrLdapTimeoutSupported | read-only | mandatory | 0 indicates the LDAP timeout is not supported. 1 indicates the LDAP timeout is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.11 | ScalarbrLdapServerCount | read-only | mandatory | Maximum number of LDAP Server INDEX. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12 | TablebrLdapServerInfoTable | not-accessible | mandatory | This table represents LDAP Server Info. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1 | RowbrLdapServerInfoEntry | not-accessible | mandatory | A row in the LdapServerInfo table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.1 | ColumnbrLdapServerInfoIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.2 | ColumnbrLdapServerName | read-write | mandatory | The LDAP server name. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.3 | ColumnbrLdapServerPort | read-write | mandatory | The LDAP server port number. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.4 | ColumnbrLdapServerAuth | read-write | mandatory | The LDAP server authentication method. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.5 | ColumnbrLdapServerUserDN | read-write | mandatory | The LDAP server user DN. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.6 | ColumnbrLdapServerPassword | read-write | mandatory | The LDAP server password. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.7 | ColumnbrLdapServerPasswordSet | read-only | mandatory | Returns 1 if the LDAP server password is set, 0 if not set. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.8 | ColumnbrLdapServerBaseDN | read-write | mandatory | The LDAP server base DN. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.10 | ColumnbrLdapServerAttrEMail | read-write | mandatory | The LDAP server attribute or e-mail. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.11 | ColumnbrLdapServerAttrFAXNumber | read-write | mandatory | The LDAP server attribute or facsimile telephone number. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.12 | ColumnbrLdapServerAttrDetail1 | read-write | mandatory | The LDAP server attribute or detail 1. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.13 | ColumnbrLdapServerAttrDetail2 | read-write | mandatory | The LDAP server attribute or detail 2. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.14 | ColumnbrLdapServerAttrDetail3 | read-write | mandatory | The LDAP server attribute or detail 3. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.15 | ColumnbrLdapServerAttrDetail4 | read-write | mandatory | The LDAP server attribute or detail 4. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.16 | ColumnbrLdapServerAttrDetailEnable1 | read-write | mandatory | Enable flag of the LDAP server attribute of detail 1. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.17 | ColumnbrLdapServerAttrDetailEnable2 | read-write | mandatory | Enable flag of the LDAP server attribute of detail 2. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.18 | ColumnbrLdapServerAttrDetailEnable3 | read-write | mandatory | Enable flag of the LDAP server attribute of detail 3. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.19 | ColumnbrLdapServerAttrDetailEnable4 | read-write | mandatory | Enable flag of the LDAP server attribute of detail 4. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.20 | ColumnbrLdapKerberosServerName | read-write | mandatory | The Kerberos server name for LDAP. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.12.1.21 | ColumnbrLdapKerberosServerPort | read-write | mandatory | The Kerberos server port number for LDAP. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.21 | ScalarbrLdapServerAttrNameCount | read-only | mandatory | Maximum number of LDAP Server Attribute of name INDEX. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.22 | TablebrLdapServerAttrNameTable | not-accessible | mandatory | This table represents LDAP Server Attribute of name. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.22.1 | RowbrLdapServerAttrNameEntry | not-accessible | mandatory | A row in the LdapServerAttributeName table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.22.1.1 | ColumnbrLdapServerAttrNameIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.22.1.2 | ColumnbrLdapServerAttrName | read-write | mandatory | The LDAP server attribute of name. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.19.99 | ScalarbrLdapSetDefault | read-write | mandatory | Setting the value resets all LDAP parameters to their factory default value. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.20 | NodebroriginalTFTP | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.20.1 | ScalarbrTFTPSupported | read-only | mandatory | 0 indicates the TFTP protocol is not supported. 1 indicates TFTP support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.20.2 | ScalarbrTFTPEnable | read-write | mandatory | 0 indicates the TFTP protocol is not enabled. 1 indicates that the TFTP protocol is enabled. Writing a non-zero value will enable the TFTP protocol if it is su… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.21 | NodebroriginalHTTPS | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.21.1 | ScalarbrHTTPSSupported | read-only | mandatory | 0 indicates the HTTPS/IPPS protocol is not supported. 1 indicates HTTPS/IPPS support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.21.2 | ScalarbrHTTPSEnable | read-write | mandatory | 0 indicates the HTTPS/IPPS protocol is not enabled. 1 indicates that the HTTPS/IPPS protocol is enabled. Writing a non-zero value will enable the HTTPS/IPPS pr… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.22 | NodebroriginalLPD | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.22.1 | ScalarbrLPDSupported | read-only | mandatory | 0 indicates the LPD protocol is not supported. 1 indicates LPD support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.22.2 | ScalarbrLPDEnable | read-write | mandatory | 0 indicates the LPD protocol is not enabled. 1 indicates that the LPD protocol is enabled. Writing a non-zero value will enable the LPD protocol if it is suppo… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.23 | NodebroriginalRawPort | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.23.1 | ScalarbrRawPortSupported | read-only | mandatory | 0 indicates the RawPort protocol is not supported. 1 indicates RawPort support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.23.2 | ScalarbrRawPortEnable | read-write | mandatory | 0 indicates the RawPort protocol is not enabled. 1 indicates that the RawPort protocol is enabled. Writing a non-zero value will enable the RawPort protocol if… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.24 | NodebroriginalLLTD | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.24.1 | ScalarbrLLTDSupported | read-only | mandatory | 0 indicates the LLTD protocol is not supported. 1 indicates LLTD support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.24.2 | ScalarbrLLTDEnable | read-write | mandatory | 0 indicates the LLTD protocol is not enabled. 1 indicates that the LLTD protocol is enabled. Writing a non-zero value will enable the LLTD protocol if it is su… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.25 | NodebroriginalWebServices | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.25.1 | ScalarbrWebServicesSupported | read-only | mandatory | 0 indicates the WebServices protocol is not supported. 1 indicates WebServices support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.25.2 | ScalarbrWebServicesEnable | read-write | mandatory | 0 indicates the WebServices protocol is not enabled. 1 indicates that the WebServices protocol is enabled. Writing a non-zero value will enable the WebServices… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.25.3 | ScalarbrWebServicesRegularPortEnable | read-write | mandatory | 0 indicates that the WebServices regular port is not enabled. 1 indicates that the WebServices regular port is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.25.4 | ScalarbrWebServicesSSLPortEnable | read-write | mandatory | 0 indicates that the WebServices SSL port is not enabled. 1 indicates that the WebServices SSL port is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.26 | NodebroriginalLLMNR | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.26.1 | ScalarbrLLMNREnable | read-write | mandatory | 0 indicates the LLMNR protocol is not enabled. 1 indicates that the LLMNR protocol is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.27 | NodebroriginalKerberos | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.27.1 | ScalarbrKerberosSupported | read-only | mandatory | 0 indicates the Kerberos protocol is not supported. 1 indicates Kerberos support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.28 | NodebroriginalCIFS | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.28.1 | ScalarbrCIFSSupported | read-only | mandatory | 0 indicates the CIFS protocol is not supported. 1 indicates CIFS support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.28.2 | ScalarbrCIFSEnable | read-write | mandatory | 0 indicates the CIFS protocol is not enabled. 1 indicates that the CIFS protocol is enabled. Writing a non-zero value will enable the CIFS protocol if it is su… |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.29 | NodebroriginalSNTP | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.29.1 | ScalarbrSNTPCSupported | read-only | mandatory | 0 indicates the SNTP is not supported. 1 indicates SNTP is supported. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.29.2 | ScalarbrSNTPCEnable | read-write | mandatory | 0 indicates the SNTP is not disabled. 1 indicates that the SNTP is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.29.3 | ScalarbrSNTPCServerMethod | read-write | mandatory | 1 indicates SNTP Server Method is AUTO. 2 indicates SNTP Server Method is STATIC. 3 indicates SNTP Server Method is PRESET. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.29.4 | ScalarbrSNTPCSyncMethod | read-write | mandatory | 1 indicates Synchronous Method is AUTO. 2 indicates Synchronous Method is STATIC. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.29.5 | ScalarbrSNTPCIntervalMin | read-write | mandatory | The minimum value of synchronous interval. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.29.6 | ScalarbrSNTPCInterval | read-write | mandatory | The synchronous interval is used for synchronous method INTERVAL. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.29.7 | ScalarbrSNTPCSyncResult | read-only | mandatory | The result of the last checking time. 1: Success 2: Synchronizing 3: Failed 4: Not yet checking |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.29.8 | ScalarbrSNTPCPrimaryServerName | read-write | mandatory | The primary server name of SNTP. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.29.9 | ScalarbrSNTPCPrimaryServerPort | read-write | mandatory | The port number of primary SNTP server. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.29.10 | ScalarbrSNTPCSecondaryServerName | read-write | mandatory | The secondary server name of SNTP. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.29.11 | ScalarbrSNTPCSecondaryServerPort | read-write | mandatory | The port number of secondary SNTP server. |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.100 | NodebroriginalSecurity | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.100.1 | NodebrSecurityGeneralStatus | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.100.1.1 | ScalarbrDeviceNegotiationEncryptVer | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.100.1.2 | ScalarbrpsServerCertificateNum | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.100.2 | NodebrSecurityGeneralSetup | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.100.10 | NodebrSecurityDeviceNegotiation | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.5.100.10.1 | ScalarbrDeviceNegotiationGetChallenge | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.100.10.2 | ScalarbrDeviceNegotiationConfirmPassword | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.2435.5.100.10.3 | ScalarbrDeviceNegotiationChangePassword | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.2435.10 | Nodebroriginalinternetsetting | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.10.1 | Nodebroriginalproxy | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.10.1.1 | ScalarbrProxySupported | read-only | mandatory | 0 indicates the Proxy is not supported. 1 indicates Proxy is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.10.1.2 | ScalarbrProxyEnable | read-write | mandatory | 0 indicates the Proxy is not enabled. 1 indicates that the Proxy is enabled. Writing a non-zero value will enable the Proxy if it is supported by the firmware. |
| 1.3.6.1.4.1.2435.2.4.3.2435.10.1.3 | ScalarbrProxyBypassServer | read-write | mandatory | on(2) indicates the bypass proxy server for local addresses. |
| 1.3.6.1.4.1.2435.2.4.3.2435.10.1.11 | ScalarbrProxyServerCount | read-only | mandatory | Maximum number of Proxy Server INDEX. |
| 1.3.6.1.4.1.2435.2.4.3.2435.10.1.12 | TablebrProxyServerInfoTable | not-accessible | mandatory | This table represents Proxy Server Info. |
| 1.3.6.1.4.1.2435.2.4.3.2435.10.1.12.1 | RowbrProxyServerInfoEntry | not-accessible | mandatory | A row in the ProxyServerInfo table. Rows cannot be created or deleted. |
| 1.3.6.1.4.1.2435.2.4.3.2435.10.1.12.1.1 | ColumnbrProxyServerInfoIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.2435.10.1.12.1.2 | ColumnbrProxyServerType | read-write | mandatory | The Proxy server ID. |
| 1.3.6.1.4.1.2435.2.4.3.2435.10.1.12.1.3 | ColumnbrProxyServerName | read-write | mandatory | The Proxy server name. |
| 1.3.6.1.4.1.2435.2.4.3.2435.10.1.12.1.4 | ColumnbrProxyServerPort | read-write | mandatory | The Proxy server port number. |
| 1.3.6.1.4.1.2435.2.4.3.2435.20 | NodebroriginalOtherSetting | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.20.1 | NodebroriginalJobTermination | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.20.1.1 | ScalarbrJobTerminationSupported | read-only | mandatory | 0 indicates the Job termination setting is not supported. 1 indicates the Job termination setting is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.3.2435.20.1.2 | ScalarbrJobTerminationEnable | read-write | mandatory | 0 indicates the Job termination setting is not enabled. 1 indicates the Job termination setting is enabled. |
| 1.3.6.1.4.1.2435.2.4.3.2435.20.2 | NodebroriginalSNMPTrap | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.20.2.1 | TablebrSNMPTrapTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.2435.20.2.1.1 | RowbrSNMPTrapEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.3.2435.20.2.1.1.1 | ColumnbrSNMPTrapIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.3.2435.20.2.1.1.2 | ColumnbrTCPIPServerAddress | read-write | mandatory | The Destination IP Address for SNMP Trap. |
| 1.3.6.1.4.1.2435.2.4.3.2435.20.3 | NodebroriginalLegacy | |||
| 1.3.6.1.4.1.2435.2.4.3.2435.20.3.1 | ScalarbrLegacyCompatible | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4 | NodenpMultiCards | |||
| 1.3.6.1.4.1.2435.2.4.4.99 | NodenpMultiIFSet | |||
| 1.3.6.1.4.1.2435.2.4.4.99.1 | NodebrMultiIFdns | |||
| 1.3.6.1.4.1.2435.2.4.4.99.1.1 | TablebrMultiIFDNSTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.99.1.1.1 | RowbrMultiIFDNSEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.99.1.1.1.1 | ColumnbrMultiIFTCPIPDNSIPSetup | read-write | mandatory | DNS mode 1:static 2:auto |
| 1.3.6.1.4.1.2435.2.4.4.99.1.1.1.2 | ColumnbrMultiIFPrimaryDNSIPAddress | read-write | mandatory | Primary DNS IP Address |
| 1.3.6.1.4.1.2435.2.4.4.99.1.1.1.3 | ColumnbrMultiIFSecondaryDNSIPAddress | read-write | mandatory | Secondary DNS IP Address |
| 1.3.6.1.4.1.2435.2.4.4.99.1.1.1.4 | ColumnbrMultiIFTCPIPConnectTime | read-write | mandatory | TCP/IP connect time. |
| 1.3.6.1.4.1.2435.2.4.4.1240 | NodebrnetMultiIFConfig | |||
| 1.3.6.1.4.1.2435.2.4.4.1240.1 | NodebrMultiIFconfig | |||
| 1.3.6.1.4.1.2435.2.4.4.1240.1.1 | ScalarbrMultiIFSupported | read-only | mandatory | 0 indicates the Multi Interface is not supported. 1 indicates Multi Interface is supported. |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.2 | ScalarbrMultiIFActiveIF | read-only | mandatory | 1 LAN 2 Wireless LAN 3 Both |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.3 | ScalarbrMultiIFAllSetDefault | read-write | mandatory | Setting the value resets all parameters to their factory default value. |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.4 | ScalarbrMultiIFCount | read-only | mandatory | MultiIF Count |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.5 | TablebrMultiIFConfigureTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1 | RowbrMultiIFConfigureEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.1 | ColumnbrMultiIFConfigureIndex | read-only | mandatory | The number. |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.2 | ColumnbrMultiIFType | read-only | mandatory | Interface Type |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.3 | ColumnbrMultiIFDescription | read-only | mandatory | Interface Description |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.4 | ColumnbrMultiIFNodeName | read-write | mandatory | An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name. |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.5 | ColumnbrMultiIFInterfaceEnable | read-write | mandatory | 0 indicates the Interfase is not enabled. 1 indicates the Interfase is enabled. |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.6 | ColumnbrMultiIFEnetMode | read-write | mandatory | Ethernet type. |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.7 | ColumnbrMultiIFHardwareType | read-only | mandatory | Hardware type of the print server. |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.8 | ColumnbrMultiIFNodeType | read-only | mandatory | A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-syste… |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.5.1.9 | ColumnbrMultiIFInterfaceEnableImmediate | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.6 | ScalarbrMultiIFPrimaryInterface | read-write | mandatory | Primary Interface |
| 1.3.6.1.4.1.2435.2.4.4.1240.1.7 | ScalarbrMultiIFInterfaceInformation | read-only | mandatory | 0bit Auto 1bit manual 2bit enable both 3bit disable both |
| 1.3.6.1.4.1.2435.2.4.4.1240.2 | NodebrMultiIFcontrol | |||
| 1.3.6.1.4.1.2435.2.4.4.1240.2.1 | TablebrMultiIFControlTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.2.1.1 | RowbrMultiIFControlEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.2.1.1.1 | ColumnbrMultiIFSetDefault | read-write | mandatory | Setting the value resets all parameters to their factory default value. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4 | NodebrMultiIFservice | |||
| 1.3.6.1.4.1.2435.2.4.4.1240.4.1 | TablebrMultiIFServiceTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.1.1 | RowbrMultiIFServiceEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.1.1.1 | ColumnbrMultiIFServiceCount | read-only | mandatory | Number of services on this print server. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.1.1.2 | ColumnbrMultiIFServiceStringLimit | read-only | mandatory | Maximum number of service strings supported by the print server. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.1.1.3 | ColumnbrMultiIFServiceStringCount | read-only | mandatory | Number of service strings currently defined on the print server. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.1.1.4 | ColumnbrMultiIFServiceFilterCount | read-only | mandatory | Number of service filters implemented by the device. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2 | TablebrMultiIFServiceInfoTable | not-accessible | mandatory | This table represents the attributes of a service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1 | RowbrMultiIFServiceInfoEntry | not-accessible | mandatory | A row in the services table. Rows cannot be created or deleted via direct SNMP operations. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.1 | ColumnbrMultiIFServiceIndex | read-only | mandatory | The service number. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.2 | ColumnbrMultiIFServiceName | read-write | mandatory | The service name. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.3 | ColumnbrMultiIFServicePort | read-write | mandatory | The port number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.4 | ColumnbrMultiIFServiceFilter | read-write | mandatory | Filter number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.5 | ColumnbrMultiIFServiceBOT | read-write | mandatory | Beginning of text string number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.6 | ColumnbrMultiIFServiceEOT | read-write | mandatory | End of text string number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.7 | ColumnbrMultiIFServiceMatch | read-write | mandatory | Match string number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.8 | ColumnbrMultiIFServiceReplace | read-write | mandatory | Replace string number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.9 | ColumnbrMultiIFServiceTCPPort | read-write | mandatory | TCP Port number assigned to this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.10 | ColumnbrMultiIFServiceNDSTree | read-write | mandatory | The NDS Tree. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.11 | ColumnbrMultiIFServiceNDSContext | read-write | mandatory | The NDS Context in Unicode. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.12 | ColumnbrMultiIFServiceVines | read-write | mandatory | The Vines StreetTalk name for this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.13 | ColumnbrMultiIFServiceObsolete | read-write | mandatory | Obsolete parameter that is no longer used |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.14 | ColumnbrMultiIFServiceNetwareServerCount | read-write | mandatory | The number of Netware servers enabled on this service. Modifying the value will truncate the server list to the specified number of servers. If the value set i… |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.15 | ColumnbrMultiIFServiceReceiveOnly | read-write | mandatory | When enabled, the service will only receive data, any printer responses will be discarded. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.16 | ColumnbrMultiIFServiceTCPQueued | read-write | mandatory | When enabled, the raw TCP connections to the port will be queued while waiting for the port to become available |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.17 | ColumnbrMultiIFServiceProtocolLAT | read-write | mandatory | When enabled, the LAT protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.18 | ColumnbrMultiIFServiceProtocolTCPIP | read-write | mandatory | When enabled, the TCP/IP protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.19 | ColumnbrMultiIFServiceProtocolNetware | read-write | mandatory | When enabled, the Netware protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.20 | ColumnbrMultiIFServiceProtocolAppleTalk | read-write | mandatory | When enabled, the AppleTalk protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.21 | ColumnbrMultiIFServiceProtocolBanyan | read-write | mandatory | When enabled, the Banyan protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.22 | ColumnbrMultiIFServiceProtocolDLC | read-write | mandatory | When enabled, the DLC protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.23 | ColumnbrMultiIFServiceProtocolNetBEUI | read-write | mandatory | When enabled, the NetBEUI protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.24 | ColumnbrMultiIFServiceNetwareServerMode | read-write | mandatory | Netware mode for this service. 0 = Queue Server, 1 = Remote Printer |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.25 | ColumnbrMultiIFServiceNetwareRemotePrinterNum | read-write | mandatory | Remote Printer Number for this service |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.26 | ColumnbrMultiIFServiceProtocolIPP | read-write | mandatory | When enabled, the IPP protocol will be available on this service. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.2.1.27 | ColumnbrMultiIFServiceAppleTalkType | read-write | mandatory | AppleTalk type. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.3 | TablebrMultiIFServiceStringInfoTable | not-accessible | mandatory | This table represents the service BOT/EOT/MATCH/REPLACE strings defined. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.3.1 | RowbrMultiIFServiceStringInfoEntry | not-accessible | mandatory | A row in the service string table. Rows cannot be created or deleted via direct SNMP operations. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.3.1.1 | ColumnbrMultiIFServiceStringIndex | read-only | mandatory | The string number. |
| 1.3.6.1.4.1.2435.2.4.4.1240.4.3.1.2 | ColumnbrMultiIFServiceString | read-write | mandatory | The character string definition suitable for displaying. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5 | NodebrMultiIFprotocol | |||
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2 | NodebrMultiIFtcpip | |||
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1 | TablebrMultiIFTCPIPTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1 | RowbrMultiIFTCPIPEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.1 | ColumnbrMultiIFTCPIPAddress | read-write | mandatory | IP Address assigned to the print server. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.2 | ColumnbrMultiIFTCPIPSubnetMask | read-write | mandatory | Subnet mask assigned to the print server. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.3 | ColumnbrMultiIFTCPIPGateway | read-write | mandatory | Gateway/Router address assigned to the print server |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.4 | ColumnbrMultiIFTCPIPMethod | read-write | mandatory | Method used to determine the IP Address. AUTO tries all protocols. STATIC uses the configured address. DHCP, BOOTP, and RARP use only that protocol. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.5 | ColumnbrMultiIFTCPIPUpdate | read-write | mandatory | Hardware MAC address to be updated. This value is write only. Will read back as zeros. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.6 | ColumnbrMultiIFTCPIPTimeout | read-write | mandatory | Timeout used for LPD connections. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.7 | ColumnbrMultiIFTCPIPBootTries | read-write | mandatory | Number of attempts to use BOOTP, RARP, and DHCP. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.8 | ColumnbrMultiIFTCPIPRARPNoSubnet | read-write | mandatory | If enabled, do not set the subnet mask based on the RARP response. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.9 | ColumnbrMultiIFTCPIPRARPNoGateway | read-write | mandatory | If enabled, do not set the gateway/router address based on the RARP response. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.10 | ColumnbrMultiIFTCPIPUseMethod | read-write | mandatory | Method type that used set up TCP/IP configuration. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.2.1.1.11 | ColumnbrMultiIFTCPIPMethodServer | read-write | mandatory | If TCP/IP configuration is setted up by any protocol server, this entry indicates the IP address of the server. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.8 | NodebrMultiIFnetbeui | |||
| 1.3.6.1.4.1.2435.2.4.4.1240.5.8.1 | TablebrMultiIFNetBIOSTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.8.1.1 | RowbrMultiIFNetBIOSEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.8.1.1.1 | ColumnbrMultiIFNetBIOSIPMethod | read-write | mandatory | Method used to determine the IP Address of the WINS server. AUTO tries all protocols (currently only DHCP is tried). STATIC uses the configured address. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.8.1.1.2 | ColumnbrMultiIFTCPIPNetBIOSPrimaryWINSAddr | read-write | mandatory | The IP Address of the primary WINS server. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.8.1.1.3 | ColumnbrMultiIFTCPIPNetBIOSSecondaryWINSAddr | read-write | mandatory | The IP Address of the secondary WINS server. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.8.1.1.4 | ColumnbrMultiIFNetBEUIDomain | read-write | mandatory | The NetBEUI domain name. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.12 | NodebrMultiIForiginalapipa | |||
| 1.3.6.1.4.1.2435.2.4.4.1240.5.12.1 | TablebrMultiIFAPIPATable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.12.1.1 | RowbrMultiIFAPIPAEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.12.1.1.1 | ColumnbrMultiIFAPIPASupported | read-only | mandatory | 0 indicates the APIPA protocol is not supported. 1 indicates APIPA support is implemented by the firmware |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.12.1.1.2 | ColumnbrMultiIFAPIPAEnable | read-write | mandatory | 0 indicates the APIPA protocol is not enabled. 1 indicates that the APIPA protocol is enabled. Writing a non-zero value will enable the APIPA protocol if it is… |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.14 | NodebrMultiIForiginalLAA | |||
| 1.3.6.1.4.1.2435.2.4.4.1240.5.14.1 | TablebrMultiIFLAATable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.14.1.1 | RowbrMultiIFLAAEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.14.1.1.1 | ColumnbrMultiIFLAASupported | read-only | mandatory | This value indicate if the locally administered addressing is supported. 0: Not Supported 1: Supported |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.14.1.1.2 | ColumnbrMultiIFLAAMacAddress | read-write | mandatory | A locally administered address (LAA) that replaces the factory-assigned MAC address (UAA: universally administered address). If this setting is all-zero addres… |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15 | NodebrMultiIForiginalIPv6 | |||
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.1 | TablebrMultiIFIPv6AddressCountTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.1.1 | RowbrMultiIFIPv6AddressCountEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.1.1.1 | ColumnbrMultiIFIPv6AddressCount | read-only | mandatory | IPv6Address Counter. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.2 | TablebrMultiIFIPv6AddressTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.2.1 | RowbrMultiIFIPv6AddressEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.2.1.1 | ColumnbrMultiIFIPv6AddressIndex | read-only | mandatory | index |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.2.1.2 | ColumnbrMultiIFIPv6Address | read-only | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.2.1.3 | ColumnbrMultiIFIPv6UseMethod | read-only | mandatory | Method type that used set up TCP/IP configuration. 0: Unknown (Information not supported) 1: Manually 2: DHCPv6 3: Stateless Address Auto-configuration 4: Rese… |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.2.1.4 | ColumnbrMultiIFIPv6MethodServer | read-only | mandatory | If TCP/IP configuration is setted up by any protocol server, this entry indicates the IP address of the server. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.3 | TablebrMultiIFIPv6StaticAddressCountTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.3.1 | RowbrMultiIFIPv6StaticAddressCountEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.3.1.1 | ColumnbrMultiIFIPv6StaticAddressCount | read-only | mandatory | IPv6StaticAddress Counter. |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.4 | TablebrMultiIFIPv6StaticAddressTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.4.1 | RowbrMultiIFIPv6StaticAddressEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.4.1.1 | ColumnbrMultiIFIPv6StaticAddressIndex | read-only | mandatory | index |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.4.1.2 | ColumnbrMultiIFIPv6StaticAddressEnable | read-write | mandatory | index |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.4.1.3 | ColumnbrMultiIFIPv6StaticAddress | read-write | mandatory | IPv6 Static Address |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.4.1.4 | ColumnbrMultiIFIPv6StaticAddressPrefixLength | read-write | mandatory | IPv6Address Prefix Length |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.5 | TablebrMultiIFDNSIPv6AddressTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.5.1 | RowbrMultiIFDNSIPv6AddressEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.5.1.1 | ColumnbrMultiIFPrimaryDNSIPv6Address | read-write | mandatory | Primary DNS IPv6 Address |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.15.5.1.2 | ColumnbrMultiIFSecondaryDNSIPv6Address | read-write | mandatory | Secondary DNS IPv6 Address |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.16 | NodebrMultiIForiginalWebServices | |||
| 1.3.6.1.4.1.2435.2.4.4.1240.5.16.1 | TablebrMultiIFWebServicesTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.16.1.1 | RowbrMultiIFWebServicesEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.16.1.1.1 | ColumnbrMultiIFWebServicesName | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.16.1.1.2 | ColumnbrMultiIFWebServicesInstanceID | read-write | mandatory | |
| 1.3.6.1.4.1.2435.2.4.4.1240.5.16.1.1.3 | ColumnbrMultiIFWebServicesMetadataVersion | read-write | mandatory |