Baytech-MIB-401-4
246 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | enterprises Gauge IpAddress TimeTicks |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4779 | Nodebaytech | |||
| 1.3.6.1.4.1.4779.1 | Nodebtadevices | |||
| 1.3.6.1.4.1.4779.1 | NodecommunicationLost | SEVERE: Communication to the unit has been lost. Steps to reestablish communication are in progress. Argument is timeTicks when communication was lost. | ||
| 1.3.6.1.4.1.4779.1.1 | NodesBTAIdent | |||
| 1.3.6.1.4.1.4779.1.1.1 | ScalarsBTAIdentFirmwareRev | read-only | mandatory | An 8 byte ID string identifying the DS72 firmware revision. This value is set at the factory. |
| 1.3.6.1.4.1.4779.1.1.2 | ScalarsBTAIdentSerialNumber | read-only | mandatory | A number identifying the serial number of the DS72. This value is set at the factory. |
| 1.3.6.1.4.1.4779.1.1.3 | ScalarsBTAIdentUnitName | read-write | mandatory | A 64-character string identifying the name (UnitID) of the DS72. This value is set at the factory to a default of DS72. |
| 1.3.6.1.4.1.4779.1.2 | NodesBTANetworkConfig | |||
| 1.3.6.1.4.1.4779.1.2.1 | ScalarsBTANetworkConfigBootpEnable | read-write | mandatory | Enables/disables bootp. Bootp will not take effect until the unit is reseted. |
| 1.3.6.1.4.1.4779.1.2.2 | ScalarsBTANetworkConfigDHCPEnable | read-write | mandatory | Enables/disables DHCP. DHCP will not take effect until the unit is reseted. |
| 1.3.6.1.4.1.4779.1.2.3 | ScalarsBTANetworkConfigSSHEnable | read-write | mandatory | Enables/disables SSH logins. Disable/enable SSH will take effect after the unit is reseted. |
| 1.3.6.1.4.1.4779.1.2.4 | ScalarsBTANetworkConfigTelnetEnable | read-write | mandatory | Enables/disables telnet. |
| 1.3.6.1.4.1.4779.1.2.5 | ScalarsBTANetworkConfigActivityTimeout | read-write | mandatory | A value from 0 to 120. 0 disables activity timeouts. Value represents minutes of non-activity before telnet / SSH sessions are automatically logged out. Defaul… |
| 1.3.6.1.4.1.4779.1.2.6 | ScalarsBTANetworkConfigDirectConnEnable | read-write | mandatory | Enables/disables direct port connection upon login. |
| 1.3.6.1.4.1.4779.1.2.8 | NodesBTANetworkConfigSNMP | |||
| 1.3.6.1.4.1.4779.1.2.8.1 | ScalarsBTANetworkConfigSNMPReadOnlyCommunity | read-write | mandatory | The community name to use for read only access. Maximum len 16 bytes. |
| 1.3.6.1.4.1.4779.1.2.8.2 | ScalarsBTANetworkConfigSNMPReadWriteCommunity | read-write | mandatory | The community name to use for read-write access. Maximum len 16 bytes. |
| 1.3.6.1.4.1.4779.1.2.8.3 | ScalarsBTANetworkConfigSNMPNumTrapReceivers | read-only | mandatory | The maximum number of managers to send traps to. Currently 4. |
| 1.3.6.1.4.1.4779.1.2.8.4 | TablesBTANetworkConfigSNMPTrapReceiverTable | not-accessible | mandatory | A list of managers to send traps to. The number of entries is given by the value of sBTANetworkConfigSNMPNumTrapReceivers. Maximum number of Trap Receivers is … |
| 1.3.6.1.4.1.4779.1.2.8.4.1 | RowsBTANetworkConfigSNMPTrapReceiverEntry | not-accessible | mandatory | Table of managers to send traps to. |
| 1.3.6.1.4.1.4779.1.2.8.4.1.1 | ColumntrapIndex | read-only | mandatory | The index to a trap receiver entry. |
| 1.3.6.1.4.1.4779.1.2.8.4.1.2 | ColumnreceiverAddress | read-write | mandatory | The IP address of the manager to send traps to. |
| 1.3.6.1.4.1.4779.1.2.9 | NodesBTANetworkConfigRadius | |||
| 1.3.6.1.4.1.4779.1.2.9.1 | ScalarsBTANetworkConfigRadiusEnable | read-write | mandatory | Enables / disables RADIUS telnet logins. |
| 1.3.6.1.4.1.4779.1.2.9.2 | ScalarsBTANetworkConfigRadiusPrimaryServer | read-write | mandatory | Ip address of the primary RADIUS server. |
| 1.3.6.1.4.1.4779.1.2.9.3 | ScalarsBTANetworkConfigRadiusSecondaryServer | read-write | mandatory | Ip address of the back-up RADIUS server. |
| 1.3.6.1.4.1.4779.1.2.9.4 | ScalarsBTANetworkConfigRadiusLocalLogin | read-write | mandatory | Enables / disables the use of local (usernames stored in the DS72) logins in the case that both the primary and secondary RADIUS server are not available. |
| 1.3.6.1.4.1.4779.1.2.10 | NodesBTANetworkConfigWEB | |||
| 1.3.6.1.4.1.4779.1.2.10.1 | ScalarsBTANetworkConfigWebEnable | read-write | mandatory | Enables WEB. |
| 1.3.6.1.4.1.4779.1.2.10.2 | ScalarsBTANetworkConfigWebSecureEnable | read-write | mandatory | Enables WEB Security. |
| 1.3.6.1.4.1.4779.1.2.10.3 | ScalarsBTANetworkConfigWebLoginEnable | read-write | mandatory | Enables WEB Login. |
| 1.3.6.1.4.1.4779.1.2.10.4 | ScalarsBTANetworkConfigWebActivityTimeout | read-write | mandatory | A value from 0 to 120. 0 disables WEB activity timeouts. Value represents minutes of non-activity before WEB sessions are automatically logged out. Default is … |
| 1.3.6.1.4.1.4779.1.3 | NodesBTAModules | |||
| 1.3.6.1.4.1.4779.1.3.1 | ScalarsBTAModulesNumberOfModules | read-only | mandatory | Number of modules installed into the DS unit. |
| 1.3.6.1.4.1.4779.1.3.2 | ScalarsBTAModulesModulesInstalled | read-only | mandatory | A character string listing the modules installed seperated by commas. Each module is identifed by a two digit number indicating the slot. For example 02,03,04,… |
| 1.3.6.1.4.1.4779.1.3.3 | ScalarsBTAModulesResetModulesCmd | read-only | deprecated | This command is no longer supported. |
| 1.3.6.1.4.1.4779.1.3.4 | ScalarsBTAModulesNumberOfIntelligentModules | read-only | mandatory | The number of Intelligent Modules installed in the DS Unit. |
| 1.3.6.1.4.1.4779.1.3.5 | NodesBTAModulesRPC | |||
| 1.3.6.1.4.1.4779.1.3.5.1 | ScalarsBTAModulesNumberOfRPCModules | read-only | mandatory | The number of DS30 Modules installed in the DS Unit. |
| 1.3.6.1.4.1.4779.1.3.5.2 | TablesBTAModulesRPCTable | not-accessible | mandatory | Allows for control of individual outlets and individual RPC modules. |
| 1.3.6.1.4.1.4779.1.3.5.2.1 | RowsBTAModulesRPCEntry | not-accessible | mandatory | The RPCs to control and get status on. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.1 | ColumnsBTAModulesRPCIndex | read-only | mandatory | The index into the RPC table. Indexes for rpcs attached to ds74 modules are calculate with the following formula: ((module - 2) * 4) + port. For example module… |
| 1.3.6.1.4.1.4779.1.3.5.2.1.2 | ColumnsBTAModulesRPCName | read-write | mandatory | The name (unit id) of the rpc. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.3 | ColumnsBTAModulesRPCFirmwareVersion | read-only | mandatory | The firware version of the rpc. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.4 | ColumnsBTAModulesRPCCurrent | read-only | mandatory | The current reading for the power strip. If current measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.5 | ColumnsBTAModulesRPCMaxCurrent | read-write | mandatory | The maximum detected current reading for the power strip. If current measurement is not installed this value will always read 0. Setting this value to 0 will c… |
| 1.3.6.1.4.1.4779.1.3.5.2.1.6 | ColumnsBTAModulesRPCVoltage | read-only | mandatory | The voltage reading for the power strip. If voltage measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.7 | ColumnsBTAModulesRPCPower | read-only | mandatory | The power reading for the power strip. If power measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.8 | ColumnsBTAModulesRPCTemperature | read-only | mandatory | The temperature reading for the power strip. Readings are in degrees C. If temperature measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.9 | ColumnsBTAModulesRPCRebootTimeout | read-only | mandatory | The length of off time for automatic reboot sequences. Currently a read-only value set to the fixed reboot timeout. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.10 | ColumnsBTAModulesRPCAllOutletsCmd | read-write | mandatory | Turns all outlets on, off or reboot. 0 = off 1 = on 2 = reboot A get will return unknown (6). |
| 1.3.6.1.4.1.4779.1.3.5.2.1.11 | ColumnsBTAModulesRPCAllOutletsStatus | read-only | mandatory | Reports status of outlets in a comma deliminated string. 0 = off 1 = on 2 = reboot 3 = locked on 4 = locked off |
| 1.3.6.1.4.1.4779.1.3.5.2.1.12 | ColumnsBTAModulesRPCCurrentAlarmThreshold | read-write | mandatory | The current alarm threshold level *10. A value of 105 will set the level to 10.5. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.13 | ColumnsBTAModulesRPCOverVoltageThreshold | read-write | mandatory | The over voltage alarm threshold level *10. A value of 105 will set the level to 10.5. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.14 | ColumnsBTAModulesRPCUnderVoltageThreshold | read-write | mandatory | The under voltage alarm threshold level *10. A value of 105 will set the level to 10.5. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.15 | ColumnsBTAModulesRPCNumberOfOutlets | read-only | mandatory | Number of outlets for this RPC. This will be the size of outlet table for this RPC index. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.16 | ColumnsBTAModulesRPCCircuitBreaker | read-only | mandatory | Status of circuit breaker in power strip. 0=off 1=on. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.17 | ColumnsBTAModulesRPCOverTempThreshold | read-write | mandatory | The over temperature alarm threshold level *10. A value of 505 will set the level to 50.5. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.18 | ColumnsBTAModulesRPCUnitVA | read-only | mandatory | Total Volt-Amps for this RPC. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.19 | ColumnsBTAModulesRPCNumberOfBreakers | read-only | mandatory | Number of breakers for this RPC. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.20 | ColumnsBTAModulesRPCLowCurrentThreshold | read-write | mandatory | Low current threshold for this RPC. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.21 | ColumnsBTAModulesRPCVoltageSource | read-write | mandatory | Voltage source for this RPC. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.22 | ColumnsBTAModulesRPCSourceSwitchCount | read-only | mandatory | Count of Voltage Source Switches for this RPC. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.23 | ColumnsBTAModulesRPCNumberOfSensors | read-only | mandatory | Number of environmental sensors for this RPC. |
| 1.3.6.1.4.1.4779.1.3.5.2.1.24 | ColumnsBTAModulesRPCType | read-only | mandatory | The type of RPC installed at the indexed location. |
| 1.3.6.1.4.1.4779.1.3.5.3 | TablesBTAModulesRPCOutletTable | not-accessible | mandatory | Allows for control of individual outlets. The number of entries is contained in the sBTAModulesRPCOutletTableSize OID. |
| 1.3.6.1.4.1.4779.1.3.5.3.1 | RowsBTAModulesRPCOutletEntry | not-accessible | mandatory | The outlets to control and get status on. |
| 1.3.6.1.4.1.4779.1.3.5.3.1.1 | ColumnsBTAModulesRPCOutletModuleIndex | read-only | mandatory | The index to the outlet entry. |
| 1.3.6.1.4.1.4779.1.3.5.3.1.2 | ColumnsBTAModulesRPCOutletIndex | read-only | mandatory | The index to the outlet entry. |
| 1.3.6.1.4.1.4779.1.3.5.3.1.3 | ColumnsBTAModulesRPCOutletState | read-write | mandatory | Getting this variable will return the state of the outlet. Valid return states are unknown, on, off, lockon, lockoff. 0 = off 1 = on 2 = reboot 3 = lockon (out… |
| 1.3.6.1.4.1.4779.1.3.5.3.1.4 | ColumnsBTAModulesRPCOutletName | read-write | mandatory | The name of the outlet. Maximum size is 16 characters. |
| 1.3.6.1.4.1.4779.1.3.5.4 | ScalarsBTAModulesRPCGroupCmd | read-write | mandatory | A character string listing the outlets that need to be controlled, turned off, or turn on as a group. Command is the first character followed by a space. Valid… |
| 1.3.6.1.4.1.4779.1.3.5.5 | TablesBTAModulesRPCModPortTable | not-accessible | mandatory | Allows for control of individual outlets and individual RPC modules. The number of entries is contained in the sBTAModulesNumberOfRPCModules OID. |
| 1.3.6.1.4.1.4779.1.3.5.5.1 | RowsBTAModulesRPCModPortEntry | not-accessible | mandatory | The RPCs to control and get status on. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.1 | ColumnsRPCModuleIndex | read-only | mandatory | The module number index into the RPC table. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.2 | ColumnsRPCPortIndex | read-only | mandatory | The port number index into the RPC table. In the case of ds30 modules this number is always 1. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.3 | ColumnsRPCType | read-only | mandatory | Type of RPC at the module, port index. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.4 | ColumnsRPCName | read-write | mandatory | The name (unit id) of the rpc module. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.5 | ColumnsRPCFirmwareVersion | read-only | mandatory | The firware version of the rpc module. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.6 | ColumnsRPCCurrent | read-only | mandatory | The current reading for the power strip. If current measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.7 | ColumnsRPCMaxCurrent | read-write | mandatory | The maximum detected current reading for the power strip. If current measurement is not installed this value will always read 0. Setting this value to 0 will c… |
| 1.3.6.1.4.1.4779.1.3.5.5.1.8 | ColumnsRPCVoltage | read-only | mandatory | The voltage reading for the power strip. If voltage measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.9 | ColumnsRPCPower | read-only | mandatory | The power reading for the power strip. If power measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.10 | ColumnsRPCTemperature | read-only | mandatory | The temperature reading for the power strip. Readings are in degrees C. If temperature measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.11 | ColumnsRPCRebootTimeout | read-write | mandatory | The length of off time for automatic reboot sequences. Currently a read-only value set to the fixed reboot timeout. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.12 | ColumnsRPCAllOutletsCmd | read-write | mandatory | Turns all outlets on, off or reboot. 0 = off 1 = on 2 = reboot 3 = lockon (will lock outlets to on state) 4 = lockoff (will lock outlets to off state) 5 = unlo… |
| 1.3.6.1.4.1.4779.1.3.5.5.1.13 | ColumnsRPCAllOutletsStatus | read-only | mandatory | Reports status of outlets in a comma deliminated string. 0 = off 1 = on 2 = reboot 3 = locked on 4 = locked off |
| 1.3.6.1.4.1.4779.1.3.5.5.1.14 | ColumnsRPCCurrentAlarmThreshold | read-write | mandatory | The current alarm threshold level *10. A value of 105 will set the level to 10.5. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.15 | ColumnsRPCOverVoltageThreshold | read-write | mandatory | The over voltage alarm threshold level *10. A value of 105 will set the level to 10.5. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.16 | ColumnsRPCUnderVoltageThreshold | read-write | mandatory | The under voltage alarm threshold level *10. A value of 105 will set the level to 10.5. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.17 | ColumnsRPCNumberOfOutlets | read-only | mandatory | Number of outlets for this RPC. This will be the size of outlet table for this RPC index. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.18 | ColumnsRPCCircuitBreaker | read-only | mandatory | Status of circuit breaker in power strip. 0=off 1=on. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.19 | ColumnsRPCOverTempThreshold | read-write | mandatory | The over temperature alarm threshold level *10. A value of 505 will set the level to 50.5. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.20 | ColumnsRPCUnitVA | read-only | mandatory | Number of outlets for this RPC. This will be the size of outlet table for this RPC index. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.21 | ColumnsRPCNumberOfBreakers | read-only | mandatory | Number of breakers for this RPC. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.22 | ColumnsRPCLowCurrentThreshold | read-write | mandatory | Low current threshold for this RPC. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.23 | ColumnsRPCVoltageSource | read-write | mandatory | Voltage source for this RPC. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.24 | ColumnsRPCSourceSwitchCount | read-write | mandatory | Voltage source switch count for this RPC. |
| 1.3.6.1.4.1.4779.1.3.5.5.1.25 | ColumnsRPCNumberOfSensors | read-only | mandatory | Number of sensors for this RPC. |
| 1.3.6.1.4.1.4779.1.3.5.6 | TablesBTAModulesRPCModPortOutletTable | not-accessible | mandatory | Allows for control of individual outlets. The number of entries is contained in the sBTAModulesRPCOutletTableSize OID. |
| 1.3.6.1.4.1.4779.1.3.5.6.1 | RowsBTAModulesRPCModPortOutletEntry | not-accessible | mandatory | The outlets to control and get status on. |
| 1.3.6.1.4.1.4779.1.3.5.6.1.1 | ColumnsRPCOutletModuleIndex | read-only | mandatory | The module index to the outlet entry. |
| 1.3.6.1.4.1.4779.1.3.5.6.1.2 | ColumnsRPCOutletPortIndex | read-only | mandatory | The port index to the outlet entry. In the case of ds30s this number is always 1. |
| 1.3.6.1.4.1.4779.1.3.5.6.1.3 | ColumnsRPCOutletIndex | read-only | mandatory | The outlet index to the outlet entry. |
| 1.3.6.1.4.1.4779.1.3.5.6.1.4 | ColumnsRPCOutletState | read-write | mandatory | Getting this variable will return the state of the outlet. Valid return states are unknown, on, off, lockon, lockoff. 0 = off 1 = on 2 = reboot 3 = lockon (out… |
| 1.3.6.1.4.1.4779.1.3.5.6.1.5 | ColumnsRPCOutletName | read-write | mandatory | The name of the outlet. Maximum size is 16 characters. |
| 1.3.6.1.4.1.4779.1.3.5.7 | ScalarsBTAModulesRPCModPortGroupCmd | read-write | mandatory | A character string listing the outlets that need to be rebooted, turned off, or turn on as a group. Command is the first character followed by a space. Valid c… |
| 1.3.6.1.4.1.4779.1.3.5.8 | TablesBTAModulesRPCCurrentGroupsCurrentTable | not-accessible | mandatory | A list of total current for RPCs in each current group |
| 1.3.6.1.4.1.4779.1.3.5.8.1 | RowsBTAModulesRPCCurrentGroupsCurrentEntry | not-accessible | mandatory | Table of total current measurement by group |
| 1.3.6.1.4.1.4779.1.3.5.8.1.1 | ColumngroupCurrentIndex | read-only | mandatory | The index to a group total current. |
| 1.3.6.1.4.1.4779.1.3.5.8.1.2 | ColumngroupCurrent | read-only | mandatory | Current total for all RPCs in group. |
| 1.3.6.1.4.1.4779.1.3.5.8.1.3 | ColumnrpcGroup | read-write | mandatory | A character string listing the RPCs, by port index, that will be included in a measurement of total current. For each group, a sum will be periodically compute… |
| 1.3.6.1.4.1.4779.1.3.5.8.1.4 | ColumnwarningThreshold | read-write | mandatory | The current level, in tenths of an amp, that will cause a Current Level Warning trap to be sent if the total current for the associated group if exceeded. Conv… |
| 1.3.6.1.4.1.4779.1.3.5.8.1.5 | ColumnemergencyThreshold | read-write | mandatory | The current level, in tenths of an amp, that will cause a Current Level Emergency trap to be sent if the total current for the associated group if exceeded. Co… |
| 1.3.6.1.4.1.4779.1.3.5.9 | TablesBTAModulesRPCBreakersTable | not-accessible | mandatory | Allows monitoring of individual outlet strips on RPCs. |
| 1.3.6.1.4.1.4779.1.3.5.9.1 | RowsBTAModulesRPCBreakersEntry | not-accessible | mandatory | Status organization by breaker. |
| 1.3.6.1.4.1.4779.1.3.5.9.1.1 | ColumnsBTAModulesRPCBreakersModulesIndex | read-only | mandatory | The index into the RPC table. |
| 1.3.6.1.4.1.4779.1.3.5.9.1.2 | ColumnsBTAModulesRPCBreakersBreakersIndex | read-only | mandatory | The index into the RPC breaker table. |
| 1.3.6.1.4.1.4779.1.3.5.9.1.3 | ColumnsBTAModulesRPCBreakersCircuitBreaker | read-only | mandatory | Status of circuit breaker in power strip. 0=off 1=on. |
| 1.3.6.1.4.1.4779.1.3.5.9.1.4 | ColumnsBTAModulesRPCBreakersCurrent | read-only | mandatory | The detected current reading for the power strip. If current measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.9.1.5 | ColumnsBTAModulesRPCBreakersMaxCurrent | read-only | mandatory | The maximum detected current reading for the power strip. If current measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.9.1.6 | ColumnsBTAModulesRPCBreakersVoltage | read-only | mandatory | The voltage reading for the power strip. If voltage measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.9.1.7 | ColumnsBTAModulesRPCBreakersPower | read-only | mandatory | The power reading for the power strip. If voltage measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.9.1.8 | ColumnsBTAModulesRPCBreakersVA | read-only | mandatory | The volt-amps reading for the power strip. If voltage measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.9.1.9 | ColumnsBTAModulesRPCBreakersCurrentAlarmThreshold | read-write | mandatory | The current alarm threshold level *10. A value of 105 will set the level to 10.5. |
| 1.3.6.1.4.1.4779.1.3.5.10 | TablesRPCModPortBreakersTable | not-accessible | mandatory | Allows monitoring of individual outlet strips on RPCs. |
| 1.3.6.1.4.1.4779.1.3.5.10.1 | RowsRPCModPortBreakersEntry | not-accessible | mandatory | Status organization by breaker. |
| 1.3.6.1.4.1.4779.1.3.5.10.1.1 | ColumnsRPCBreakersModIndex | read-only | mandatory | The module index into the RPC breaker table. |
| 1.3.6.1.4.1.4779.1.3.5.10.1.2 | ColumnsRPCBreakersPortIndex | read-only | mandatory | The port index into the RPC breaker table. |
| 1.3.6.1.4.1.4779.1.3.5.10.1.3 | ColumnsRPCBreakersBreakersIndex | read-only | mandatory | The breaker index into the RPC breaker table. |
| 1.3.6.1.4.1.4779.1.3.5.10.1.4 | ColumnsRPCBreakersCircuitBreaker | read-only | mandatory | Status of circuit breaker in power strip. 0=off 1=on. |
| 1.3.6.1.4.1.4779.1.3.5.10.1.5 | ColumnsRPCBreakersCurrent | read-only | mandatory | The detected current reading for the power strip. If current measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.10.1.6 | ColumnsRPCBreakersMaxCurrent | read-only | mandatory | The maximum detected current reading for the power strip. If current measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.10.1.7 | ColumnsRPCBreakersVoltage | read-only | mandatory | The voltage reading for the power strip. If voltage measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.10.1.8 | ColumnsRPCBreakersPower | read-only | mandatory | The power reading for the power strip. If voltage measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.10.1.9 | ColumnsRPCBreakersVA | read-only | mandatory | The volt-amps reading for the power strip. If voltage measurement is not installed this value will always read 0. |
| 1.3.6.1.4.1.4779.1.3.5.10.1.10 | ColumnsRPCBreakersCurrentAlarmThreshold | read-write | mandatory | The current alarm threshold level x10. A value of 105 will set the level to 10.5. |
| 1.3.6.1.4.1.4779.1.3.6 | NodesBTAModulesSerial | |||
| 1.3.6.1.4.1.4779.1.3.7 | NodesBTAModulesModem | |||
| 1.3.6.1.4.1.4779.1.4 | NodesBTAControl | |||
| 1.3.6.1.4.1.4779.1.4.1 | ScalarsBTAControlResetUnit | read-write | mandatory | Setting this value to 1 will cause the unit to reset. A get of this OID will return 0. |
| 1.3.6.1.4.1.4779.1.4.2 | ScalarsBTAControlResetModules | read-write | mandatory | Setting this value to 1 will cause the unit to reset modules simular to the telnet RM command. A get of this OID will return 0. |
| 1.3.6.1.4.1.4779.1.4.3 | ScalarsBTAControlNumOfLoggedUsers | read-only | mandatory | Number of users logged in via telnet or SSH. |
| 1.3.6.1.4.1.4779.1.4.4 | TablesBTAControlUserTable | not-accessible | mandatory | A list of users and user information. The number of entries is contained in the sBTAControlNumOfLoggedUsers OID. |
| 1.3.6.1.4.1.4779.1.4.4.1 | RowsBTAControlUserEntry | not-accessible | mandatory | The users to get status on. |
| 1.3.6.1.4.1.4779.1.4.4.1.1 | ColumnsBTAControlUserIndex | read-only | mandatory | The index to the user entry. |
| 1.3.6.1.4.1.4779.1.4.4.1.2 | ColumnsBTAControlUserName | read-only | mandatory | The username of the user. |
| 1.3.6.1.4.1.4779.1.4.4.1.3 | ColumnsBTAControlUserAddress | read-only | mandatory | The IP address of the user. |
| 1.3.6.1.4.1.4779.1.4.4.1.4 | ColumnsBTAControlUserConnection | read-only | mandatory | Type of connection. If unknown, user is logging out or the connection is invalid. |
| 1.3.6.1.4.1.4779.1.4.4.1.5 | ColumnsBTAControlUserConnModule | read-only | mandatory | If the user is connected to a module, this value will report the module number connected to. If the value is 0 the user is not connected to a module. |
| 1.3.6.1.4.1.4779.1.4.4.1.6 | ColumnsBTAControlUserConnPort | read-only | mandatory | The port number with in a module that the user is connected to. This usually only applies to connections to DS74 serial modules. Intelligent modules connection… |
| 1.3.6.1.4.1.4779.1.4.4.1.7 | ColumnsBTAControlUserTerminateUser | read-write | mandatory | Settings this OID to anything but 0 will terminate (log out) the user. A get of this OID will return 0. |
| 1.3.6.1.4.1.4779.1.5 | NodesBTAFileTransfer | |||
| 1.3.6.1.4.1.4779.1.5.1 | ScalarsBTAFileTransferEnableUpgradeFTPFileTransfer | read-write | mandatory | Setting this OID to enableUpgradeFileTransferDownloadViaFTP (1) will start the FTP server and place the DS72 in upgrade mode. An FTP connection may then be est… |
| 1.3.6.1.4.1.4779.1.6 | NodesBTAEnvironmental | |||
| 1.3.6.1.4.1.4779.1.6.1 | TablesBTAModulesEnvironmentalObjectsTable | not-accessible | mandatory | Allows monitoring of individual outlet strips on RPCs. |
| 1.3.6.1.4.1.4779.1.6.1.1 | RowsBTAModulesEnvironmentalObjectsEntry | not-accessible | mandatory | Status organization by sensor. |
| 1.3.6.1.4.1.4779.1.6.1.1.1 | ColumnsBTAModulesEnvironmentalModulesIndex | read-only | mandatory | Module Index for Environemntal table |
| 1.3.6.1.4.1.4779.1.6.1.1.2 | ColumnsBTAModulesEnvironmentalSensorsIndex | read-only | mandatory | Sensor Index for Environemntal table |
| 1.3.6.1.4.1.4779.1.6.1.1.3 | ColumnsBTAModulesEnvironmentalType | read-only | mandatory | Environmental Object Type. |
| 1.3.6.1.4.1.4779.1.6.1.1.4 | ColumnsBTAModulesEnvironmentalName | read-write | mandatory | The name for the environmental object. |
| 1.3.6.1.4.1.4779.1.6.1.1.5 | ColumnsBTAModulesEnvironmentalMeasurement | read-only | mandatory | The measurement or state for the object. |
| 1.3.6.1.4.1.4779.1.6.1.1.6 | ColumnsBTAModulesEnvironmentalHiThreshold | read-write | mandatory | Hi threshold for object. |
| 1.3.6.1.4.1.4779.1.6.1.1.7 | ColumnsBTAModulesEnvironmentalLoThreshold | read-write | mandatory | Lo threshold for object. |
| 1.3.6.1.4.1.4779.1.6.1.1.8 | ColumnsBTAModulesEnvironmentalMax | read-write | mandatory | Max value recorded for object since last reset. |
| 1.3.6.1.4.1.4779.1.6.1.1.9 | ColumnsBTAModulesEnvironmentalMin | read-write | mandatory | Min value recorded for object since last reset. |
| 1.3.6.1.4.1.4779.1.6.1.1.10 | ColumnsBTAModulesEnvironmentalHiThresholdEn | read-write | mandatory | Hi threshold enable for object. |
| 1.3.6.1.4.1.4779.1.6.1.1.11 | ColumnsBTAModulesEnvironmentalLoThresholdEn | read-write | mandatory | Lo threshold enable for object. |
| 1.3.6.1.4.1.4779.1.6.1.1.12 | ColumnsBTAModulesEnvironmentalStateTrapEn | read-write | mandatory | Trap enable for environmental sensors with contacts. |
| 1.3.6.1.4.1.4779.1.6.2 | TablesRPCEnvironmentalObjectsTable | not-accessible | mandatory | Allows monitoring of individual outlet strips on RPCs. |
| 1.3.6.1.4.1.4779.1.6.2.1 | RowsRPCEnvironmentalObjectsEntry | not-accessible | mandatory | Status organization by sensor. |
| 1.3.6.1.4.1.4779.1.6.2.1.1 | ColumnsRPCEnvironmentalModuleIndex | read-only | mandatory | Module Index for Environemntal table |
| 1.3.6.1.4.1.4779.1.6.2.1.2 | ColumnsRPCEnvironmentalPortIndex | read-only | mandatory | Port Index for Environemntal table |
| 1.3.6.1.4.1.4779.1.6.2.1.3 | ColumnsRPCEnvironmentalSensorsIndex | read-only | mandatory | Sensor Index for Environemntal table |
| 1.3.6.1.4.1.4779.1.6.2.1.4 | ColumnsRPCEnvironmentalType | read-only | mandatory | Environmental Object Type. |
| 1.3.6.1.4.1.4779.1.6.2.1.5 | ColumnsRPCEnvironmentalName | read-write | mandatory | The name for the environmental object. |
| 1.3.6.1.4.1.4779.1.6.2.1.6 | ColumnsRPCEnvironmentalMeasurement | read-only | mandatory | The measurement or state for the object. |
| 1.3.6.1.4.1.4779.1.6.2.1.7 | ColumnsRPCEnvironmentalHiThreshold | read-write | mandatory | Hi threshold for object. |
| 1.3.6.1.4.1.4779.1.6.2.1.8 | ColumnsRPCEnvironmentalLoThreshold | read-write | mandatory | Lo threshold for object. |
| 1.3.6.1.4.1.4779.1.6.2.1.9 | ColumnsRPCEnvironmentalMax | read-write | mandatory | Max value recorded for object since last reset. |
| 1.3.6.1.4.1.4779.1.6.2.1.10 | ColumnsRPCEnvironmentalMin | read-write | mandatory | Min value recorded for object since last reset. |
| 1.3.6.1.4.1.4779.1.6.2.1.11 | ColumnsRPCEnvironmentalHiThresholdEn | read-write | mandatory | Hi threshold enable for object. |
| 1.3.6.1.4.1.4779.1.6.2.1.12 | ColumnsRPCEnvironmentalLoThresholdEn | read-write | mandatory | Lo threshold enable for object. |
| 1.3.6.1.4.1.4779.1.6.2.1.13 | ColumnsRPCEnvironmentalStateTrapEn | read-write | mandatory | Trap enable for environmental sensors with contacts. |
| 1.3.6.1.4.1.4779.1.6.3 | ScalarsBTAEnvironmentalAllTemperatureSensorsHiThreshold | read-write | mandatory | Hi Threshold for all temperature sensors. |
| 1.3.6.1.4.1.4779.1.6.4 | ScalarsBTAEnvironmentalAllTemperatureSensorsLoThreshold | read-write | mandatory | Lo Threshold for all temperature sensors. |
| 1.3.6.1.4.1.4779.1.6.5 | ScalarsBTAEnvironmentalAllTemperatureSensorsHiThresholdTrapEnable | read-write | mandatory | Hi Threshold trap enable for all temperature sensors. |
| 1.3.6.1.4.1.4779.1.6.6 | ScalarsBTAEnvironmentalAllTemperatureSensorsLoThresholdTrapEnable | read-write | mandatory | Lo Threshold trap enable for all temperature sensors. |
| 1.3.6.1.4.1.4779.1.6.7 | ScalarsBTAEnvironmentalAllSensorsStateTrapEnable | read-write | mandatory | State change environmental sensor (ex: contact) trap enable. |
| 1.3.6.1.4.1.4779.2 | NodecommunicationEstablished | INFORMATION: Communication with the unit has been established. Argument is timeTicks when communication was established. | ||
| 1.3.6.1.4.1.4779.3 | Nodemtrapargs | |||
| 1.3.6.1.4.1.4779.3 | NodeoutletOn | WARNING: The specified RPC outlet has turned on. If sBTAOutletIndex equals zero, then all outlets have turned on. | ||
| 1.3.6.1.4.1.4779.3.1 | ScalarmtrapargsInteger | read-only | mandatory | This OID allows baytech traps to be sent with an integer argument that may not be defined in the baytech MIB. A get of this OID will return 0. |
| 1.3.6.1.4.1.4779.3.2 | ScalarmtrapargsIpAddress | read-only | mandatory | This OID allows bayteh traps to be sent with an IP address argument that may not be defined in the baytech MIB. A get of this OID will return 0.0.0.0. |
| 1.3.6.1.4.1.4779.3.3 | ScalarmtrapargsString | read-only | mandatory | This OID allows baytech traps to be sent with an octet string argument that may not be defined in the baytech MIB. A get of this OID will return a NULL string. |
| 1.3.6.1.4.1.4779.3.4 | ScalarmtrapargsGauge | read-only | mandatory | This OID allows baytech traps to be sent with a Gauge argument that may not be defined in the baytech MIB. A get of this OID will return 0. |
| 1.3.6.1.4.1.4779.3.5 | ScalarmtrapargsTimeTicks | read-only | mandatory | This OID allows baytech traps to be sent with a TimeTicks argument that may not be defined in the baytech MIB. A get of this OID will return 0. |
| 1.3.6.1.4.1.4779.3.6 | ScalarsBTAModuleIndex | read-only | mandatory | This OID allows baytech traps to be sent with an integer argument that may not be defined in the baytech MIB. This is an index to a specific DS module. Value w… |
| 1.3.6.1.4.1.4779.3.7 | ScalarsBTAOutletIndex | read-only | mandatory | This OID allows baytech traps to be sent with an integer argument that may not be defined in the baytech MIB. This is an index to a specific outlet in a DS mod… |
| 1.3.6.1.4.1.4779.3.8 | ScalarsBTAPortIndex | read-only | mandatory | This OID allows baytech traps to be sent with an integer argument that may not be defined in the baytech MIB. This is an index to a specific outlet in a DS mod… |
| 1.3.6.1.4.1.4779.3.9 | ScalarsBTAVoltageSource | read-write | mandatory | This OID allows baytech traps to be sent with an integer argument that may not be defined in the baytech MIB. This is the number associated with the voltage so… |
| 1.3.6.1.4.1.4779.3.10 | ScalarsBTASourceSwitchCount | read-only | mandatory | This OID allows baytech traps to be sent with an integer argument that may not be defined in the baytech MIB. This is the number associated with the number of … |
| 1.3.6.1.4.1.4779.3.11 | ScalarsBTASensorIndex | read-only | mandatory | This OID allows baytech traps to be sent with an integer argument that may not be defined in the baytech MIB. This is an index to a specific sensor in a DS mod… |
| 1.3.6.1.4.1.4779.3.12 | ScalarsBTABreakerIndex | read-only | mandatory | This is an object which is sent along with a trap to designate a breaker number pertinent to a particular trap. This value will range from 1 to the total numbe… |
| 1.3.6.1.4.1.4779.4 | NodeoutletOff | WARNING: The specified RPC outlet has turned off. If sBTAOutletIndex equals zero, then all outlets have turned off. | ||
| 1.3.6.1.4.1.4779.5 | NodeoutletReboot | WARNING: The specified RPC outlet has rebooted. If sBTAOutletIndex equals zero, then all outlets have rebooted. | ||
| 1.3.6.1.4.1.4779.6 | NodeoutletLocked | WARNING: The specified RPC outlet has been locked. If sBTAOutletIndex equals zero, then all outlets have been locked. | ||
| 1.3.6.1.4.1.4779.7 | NodeoutletUnlocked | WARNING: The specified RPC outlet has been unlocked. If sBTAOutletIndex equals zero, then all outlets have been unlocked. | ||
| 1.3.6.1.4.1.4779.8 | NodeconfigChangeSNMP | WARNING: The SNMP configuration has been changed. | ||
| 1.3.6.1.4.1.4779.9 | NodeconfigChangeOutlet | WARNING: The specified outlet has changed configuration. | ||
| 1.3.6.1.4.1.4779.10 | NodeaccessViolationConsole | WARNING: Someone has attempted to login via the console with the incorrect password. | ||
| 1.3.6.1.4.1.4779.11 | NodeaccessViolationNetwork | WARNING: Someone has attempted to login via the network with the incorrect password. | ||
| 1.3.6.1.4.1.4779.12 | NodeuserPasswordChange | WARNING: The password for the specified user has been changed. | ||
| 1.3.6.1.4.1.4779.13 | NodeuserAdded | WARNING: The specified user has been added. | ||
| 1.3.6.1.4.1.4779.14 | NodeuserLoggedIn | INFORMATIONAL: The specified user has logged in. | ||
| 1.3.6.1.4.1.4779.15 | NodetemperatureThresholdViolation | WARNING: A temperature threshold has been violated. The argument is the rpc index. | ||
| 1.3.6.1.4.1.4779.16 | NodetemperatureThresholdViolationCleared | INFORMATIONAL: A temperature threshold violated has been cleared. The argument is the rpc index. | ||
| 1.3.6.1.4.1.4779.17 | NodecurrentThresholdViolation | WARNING: The preset current threshold has been violated. The argument is the rpc index. | ||
| 1.3.6.1.4.1.4779.18 | NodecurrentThresholdViolationCleared | INFORMATIONAL: A current threshold violation has been cleared. The argument is the rpc index. | ||
| 1.3.6.1.4.1.4779.19 | NoderesetModulesEvent | WARNING: A reset modules (RM) command has been executed. | ||
| 1.3.6.1.4.1.4779.20 | NoderesetModulesComplete | WARNING: A reset modules (RM) command has been completed. | ||
| 1.3.6.1.4.1.4779.21 | NodeerrorExecutingSNMPCommand | WARNING: unable to execute SNMP command. String contains reason and command. | ||
| 1.3.6.1.4.1.4779.22 | NodefileTransferComplete | INFORMATIONAL: file transfer to unit complete. | ||
| 1.3.6.1.4.1.4779.23 | NodeuserTerminated | WARNING: user terminated. Argument specifies user. | ||
| 1.3.6.1.4.1.4779.24 | NodevoltageOverThresholdViolation | WARNING: Over voltage. Argument specifies rpc. | ||
| 1.3.6.1.4.1.4779.25 | NodevoltageOverThresholdViolationCleared | INFORMATIONAL: Over voltage cleared. Argument specifies rpc. | ||
| 1.3.6.1.4.1.4779.26 | NodevoltageUnderThresholdViolation | WARNING: Under voltage. Argument specifies rpc. | ||
| 1.3.6.1.4.1.4779.27 | NodevoltageUnderThresholdViolationCleared | INFORMATIONAL: Under voltage cleared. Argument specifies rpc. | ||
| 1.3.6.1.4.1.4779.28 | NodecircuitBreakerAlarm | WARNING: Circuit breaker is blown. Argument specifies rpc. | ||
| 1.3.6.1.4.1.4779.29 | NoderpcFailureAlarm | WARNING: Unable to communicate to an RPC. Argument specifies port number of RPC. | ||
| 1.3.6.1.4.1.4779.30 | NodeuserDeleted | INFORMATIONAL: The specified user has logged in. | ||
| 1.3.6.1.4.1.4779.31 | NodewarningThresholdViolation | |||
| 1.3.6.1.4.1.4779.32 | NodewarningThresholdViolationClear | |||
| 1.3.6.1.4.1.4779.33 | NodeemergencyThresholdViolation | |||
| 1.3.6.1.4.1.4779.34 | NodeemergencyThresholdViolationClear | |||
| 1.3.6.1.4.1.4779.35 | NodecircuitBreakerAlarmClearTrap | Circuit breaker has been reset. Argument specifies rpc. | ||
| 1.3.6.1.4.1.4779.36 | NodecurrentUnderThresholdViolation | WARNING: Low current. Argument specifies rpc. | ||
| 1.3.6.1.4.1.4779.37 | NodecurrentUnderThresholdViolationCleared | INFORMATIONAL: Low current cleared. Argument specifies rpc. | ||
| 1.3.6.1.4.1.4779.38 | NodevoltageSourceChangeAlarm | WARNING: RPC voltage source has changed. Arguments specify modules index, current voltage source, and count of number of times source has been switched. | ||
| 1.3.6.1.4.1.4779.39 | NodesensorTempThreshHiAlarmTrap | WARNING: Hi threshold exceeded. Arguments specify module, sensor number | ||
| 1.3.6.1.4.1.4779.40 | NodesensorTempThreshHiAlarmClearedTrap | WARNING: Hi threshold alarm cleared. Arguments specify module, sensor number | ||
| 1.3.6.1.4.1.4779.41 | NodesensorTempThreshLoAlarmTrap | WARNING: Lo threshold alarm cleared. Arguments specify module, sensor number | ||
| 1.3.6.1.4.1.4779.42 | NodesensorTempThreshLoAlarmClearedTrap | WARNING: Lo threshold alarm cleared. Arguments specify module, sensor number | ||
| 1.3.6.1.4.1.4779.43 | NodesensorStateChangeTrap | WARNING: Sensor state (contact, detector, etc) has changed. Arguments specify module, sensor number | ||
| 1.3.6.1.4.1.4779.44 | NodeconfigChangeSensor | WARNING: The specified environmental sensor has changed configuration. | ||
| 1.3.6.1.4.1.4779.45 | NodesensorTypeChange | WARNING: The specified environmental sensor is now a different type. |