CADANT-TC
56 objects
This MIB module contains the textual conventions that are shared among multiple ARRIS MIBs.
Imported Objects
| CADANT-PRODUCTS-MIB | cadant |
| SNMPv2-SMI | Counter64 Integer32 MODULE-IDENTITY |
| SNMPv2-TC | TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4998.0 | IdentitycadTextualConventions | This MIB module contains the textual conventions that are shared among multiple ARRIS MIBs. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AAAmethod | INTEGER { none(1), line(2), local(4), group(5) } | current | This TEXTUAL-CONVENTION describes the type of AAA methods available on the C4. |
| AccountingType | INTEGER { start-stop(1), stop-only(2) } | current | This TEXTUAL-CONVENTION describes the different types of accounting services. |
| AdminSrcAddrType | INTEGER { other(1), ftp(2), http(3), ipdr(4), legal-intercept(5), ntp(6), pc-dqos(7), pc-mm(8), remote-query(9), snmp-trap(10), ssh(11), syslog(12), radius(13), tacacs(14), telnet(15), dns(16) } | current | This enumeration is for setting the source interface to use with administrative services. |
| AdminState | INTEGER { up(1), down(2) } | current | The administrative or the desired states of the element and are set by the EMS. |
| CadAclString | OCTET STRING (SIZE(0..32)) | current | The name of the ACL this ACE is part of. |
| CadAclType | INTEGER { none(0), std-access-list(1), ext-access-list(2), rate-limit-access-list(3), remark(4), ipv6-access-list(5) } | current | The type of ACL this ACE is part of. |
| CadBridgeGroupId | Integer32 (33..255) | current | Uniquely identifies the bridge group. |
| CadBridgePortType | INTEGER { cm(1), cpeauth(2), cpeunauth(3), any(4), none(5) } | current | Type of traffic allowed on a bridge port. Ethernet ports allow any type of traffic. RF ports can be sub divided for CM traffic, authorized CPE traffic, and unauthorized CPE traffic. |
| CadCpeDeviceTypes | BITS { cable-modem(0), cpe(1), ps(2), mta(3), stb(4), tea(5), erouter(6), dva(7), sg(8), reserved9(9), reserved10(10), reserved11(11), reserved12(12), reserved13(13), reserved14(14), reserved15(15), reserved16(16), reserved17(17), reserved18(18), reserved19(19), reserved20(20), reserved21(21), reserved22(22), reserved23(23), reserved24(24), reserved25(25), reserved26(26), reserved27(27), reserved28(28), reserved29(29), reserved30(30), reserved31(31) } | current | CPE Device types. |
| CadDouble | Counter64 | current | This type is used to express and display 64-bit, double-precision floating-point values. |
| CadExtAclCondition | INTEGER { na(0), eq(1), ne(2), lt(3), le(4), gt(5), ge(6), range(7) } | current | This TEXTUAL-CONVENTION describes the condition of Extended ACLs. |
| CadIfDirection | INTEGER { in(1), out(2) } | current | A direction of flow on an interface. |
| CadIpPort | INTEGER (0..65535|-1) | current | The port of an IP packet. The value -1 indicates that this field is not used. |
| CadIpTos | INTEGER (0..255) | current | The type-of-service of an IP packet. The value 0 indicates that this field is not used. |
| CadIpTosMask | INTEGER (0|30|224|254|255) | current | The allowed type-of-service mask of an IP packet. 30 is used when the 4 bit TOS is specified. 224 is used when the 3 bit precedence is specified, and 254 is used when the entire 7 bit TOS is specified, 255 is used when … |
| CadProtocolType | INTEGER (0..255|-1) | current | The protocol type an IP packet (8 bits). 0 is IP, 1 is ICMP, 2 is IGMP, 6 is TCP 17 is UDP. See RFC-1700 for complete list. The value -1 indicates an invalid/unused protocol type. |
| CadTcpFlags | BITS { urg(0), ack(1), push(2), rst(3), syn(4), fin(5) } | current | The values available in the flags portion of the TCP header. |
| CardId | Integer32 (0..99) | current | Uniquely identifies the individual Circuit Pack, where 0 is an invalid CardId. |
| CardSubType | INTEGER { invalid(0), dcam192d(1), ucam96u(2), rsm56g(3), dcam144d(4), fanA(7), fanB(8), fanC(9), pemA(10), pemB(11), ccmA(12), ccmB(13), cdmA(14), cdmB(15), sam(16), unknown(98) } | current | Enumeration of more specific current Card Type. For cards with only one subtype, the type and subtype should be identical. |
| CardType | INTEGER { invalid(0), dcam(1), ucam(2), rsm(3), fan(4), pem(5), ccm(6), cdm(7), sam(8), unknown(98) } | current | Enumeration of generic Card Type. |
| CerCardSubType | INTEGER { invalid(0), fan(1), pem(2), ccm(3), cdm(4), sam(5), rsm10g(6), ucam96m24c(7), dcam192m8cAnnexA(8), dcam256m8cAnnexB(9), unknown(98) } | current | Enumeration of more specific current Card Type. For cards with only one subtype, the type and subtype should be identical. |
| CerCardType | INTEGER { invalid(0), fan(1), pem(2), ccm(3), cdm(4), sam(5), rsm(6), ucam(7), dcam(8), unknown(98) } | current | Enumeration of generic Card Type. |
| CerPicType | INTEGER { invalid(0), dcamLowPic8c(1), dcamHighPic8c(2), dcamSparePic8c(3), ucamHighPic24c(4), ucamSparePic24c(5), rsmPic(6), unknown(98) } | current | This type describes the PIC attached to the backplane behind a a card. |
| CerPortType | INTEGER { invalid(0), ureceiver(1), uchannel(2), eport10BaseT(3), eport100BaseT(4), eport1000BaseT(5), eport10000BaseT(6), macport(8), dchannelDocsis(9), dchannelVideo(10), linkAgg(11), dchannelVideoreplica(12), dchannelOfdm(13), unknown(98) } | current | Enumeration of current Port Type. |
| DiskVolumeUsageLevel | INTEGER { normal(1), minor(2), major(3), critical(4) } | current | Describe the disk volume usage level |
| DuplexStatus | INTEGER { notapplicable(0), active(1), standby(2), simplex(3), protected(4) } | current | not applicable to all components |
| EqActionType | INTEGER { notapplicable(0), initialize(1), switch(2), remove(3), restorecond(4), restoreuncd(5), systemreset(6), cardreset(7) } | current | not applicable to all components |
| FirmwareSource | INTEGER { committed(1), transient(2), boot1(3), boot2(4), unknown(5) } | current | This type describes the initial source of the firmware running on a card. Committed and transient indicate the card flash device and the downloaded image, respectively. Boot1 and Boot2 indicate which of the resident boo… |
| FlowActivityState | INTEGER { needy(1), normal(2), greedy(3) } | current | Flow Activity State describes the recent bandwidth utilization history of a service flow relative to its Service Level Agreement. A flow that is operating below its Tmin is said to be 'needy'. A flow that is operating a… |
| FlowControlMode | INTEGER { invalid(0), on(1), off(2), desired(3), unknown(4) } | current | flow control settings for a network port. |
| InetAddressIPv4or6 | OCTET STRING (SIZE (0|4|8|16|20)) | current | This TEXTUAL-CONVENTION is similar to InetAddress as defined in the INET-ADDRESS-MIB. However, InetAddressIPv4or6 does not allow DNS addresses and its address type, either IPv4 or IPv6, can be readily determined from it… |
| LineType | INTEGER { console(1), vty(2) } | current | This TEXTUAL-CONVENTION describes the type line connections available on the C4. |
| MacPortId | Integer32 (1..416) | current | A valid unique identifier for a MAC port in an E6000 system. |
| MacPortIdWithInvalid | Integer32 (0..416) | current | Identifier for a MAC port in an E6000 system. |
| OUIAddress | OCTET STRING (SIZE (3)) | current | Represents the first three(3), most significant bytes of an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in… |
| OverloadStatus | INTEGER { normal(1), yellow(2), red(3) } | current | Three levels indicating how much work the card is doing. |
| OverloadThreshold | INTEGER { low(0), medlow(1), med(2), medhigh(3), high(4) } | current | Five levels indicating when overload state transitions should occur. |
| PicType | INTEGER { invalid(0), dcamLeft(1), dcamRight(2), dcam(3), ucamRight(4), ucam(5), rsm(6), unknown(98) } | current | This type describes the PIC attached to the backplane behind a a card. |
| PortDetectedMode | INTEGER { invalid(0), fullDuplex100Mpbs(2), halfDuplex100Mpbs(3), fullDuplex10Mpbs(4), halfDuplex10Mpbs(5), fullDuplex1000Mpbs(6), halfDuplex1000Mpbs(7), fullDuplex10000Mpbs(8), sfpFullDuplex1000BaseT(9), sfpHalfDuplex1000BaseT(10), sfpFullDuplex100BaseT(11), sfpHalfDuplex100BaseT(12), sfpFullDuplex10BaseT(13), sfpHalfDuplex10BaseT(14), sfpFullDuplex1000BaseSX(15), sfpFullDuplex1000BaseLX(16), sfpFullDuplex1000BaseLH(17), sfpFullDuplex1000BaseLXLH(18), sfpFullDuplex1000BaseZX(19), sfpFullDuplex1000BaseCWDM(20), sfpFullDuplex1000BaseDWDM(21), xfpFullDuplex10GBaseSR(22), xfpFullDuplex10GBaseLRM(23), xfpFullDuplex10GBaseLR(24), xfpFullDuplex10GBaseER(25), xfpFullDuplex10GBaseZR(26), xfpFullDuplex10GBaseLX4(27), xfpFullDuplex10GBaseDWDM(28), sfpFullDuplex10GBaseSR(29), sfpFullDuplex10GBaseLRM(30), sfpFullDuplex10GBaseLR(31), sfpFullDuplex10GBaseER(32), sfpFullDuplex10GBaseZR(33), unknown (34) } | current | detected mode settings for a network port. |
| PortId | Integer32 (0..392) | current | Uniquely identifies a port on a card, where 0 is an invalid PortId. |
| PortMode | INTEGER { invalid(0), autoNegotiate(1), fullDuplex100Mpbs(2), halfDuplex100Mpbs(3), fullDuplex10Mpbs(4), halfDuplex10Mpbs(5), fullDuplex1000Mpbs(6), halfDuplex1000Mpbs(7), fullDuplex10000Mpbs(8) } | current | mode settings for a network port. |
| PortType | INTEGER { invalid(0), ureceiver(1), uchannel(2), eport10BaseT(3), eport100BaseT(4), eport1000BaseT(5), eport10000BaseT(6), macport(8), dchannelDocsis(9), dchannelVideo(10), linkAgg(11), dchannelVideoReplica(12), dchannelOfdm(13), unknown(98) } | current | Enumeration of current Port Type. |
| PrimaryState | INTEGER { is(1), oos(2) } | current | The operational state IS(1): The element is operable and available for use OOS(2): The element/resource is inoperable and unable to provide service UNEQ(3): The element/resource is unequiped. |
| SecondaryState | INTEGER { notapplicable(0), manual(1), fault(2), diagnostic(3), overload(4), normal(5), degrade(6), initializing(7), swdownload(8), firmwarepump(9), powerup(10), bootdkm(11) } | current | For each PrimaryState, there might be an associated secondary state |
| ServerType | INTEGER { telnet(1), ftp(2), snmp(3), syslog(4), radius(5), tacacs(6), other(7) } | current | This TEXTUAL-CONVENTION describes the INET services available on the SCM. |
| SshAuthMethod | INTEGER { password(1), public-key(2) } | current | This TEXTUAL-CONVENTION describes the authentication method available in SSH on the C4. |
| SshCipher | BITS { other(0), threedes(1), arcfour(2), blowfish(3), cast(4), aes(5) } | current | This TEXTUAL-CONVENTION describes the ciphers available in SSH on the C4. |
| SshCipherType | INTEGER { other(1), threedes(2), arcfour(3), blowfish(4), cast128(5), aes128(6), aes192(7), aes256(8), des(9), rc4(10) } | current | This TEXTUAL-CONVENTION describes the specific cipher type on the C4. |
| SshKeyExchangeMethod | BITS { dh-gr1-sha1(0), dh-gr14-sha1(1) } | current | This TEXTUAL-CONVENTION describes the server key exchange methods available in SSH on the E6000. |
| SshKeyType | INTEGER { unknown(0), dsa1024(1), rsa2048(2) } | current | This TEXTUAL-CONVENTION describes the server key types available in SSH on the E6000. |
| SshMacAlg | INTEGER { none(1), hmac-sha1(2), hmac-sha1-96(3), hmac-md5(4), hmac-md5-96(5) } | current | This TEXTUAL-CONVENTION describes the MAC algorithm available in SSH on the C4. |
| SshProtocol | INTEGER { ssh1(1), ssh2(2), ssh1ssh2(3) } | current | This TEXTUAL-CONVENTION describes the SSH protocol versions available in SSH on the C4. |
| SshService | INTEGER { terminal(1), sftp(2) } | current | This TEXTUAL-CONVENTION describes the SSH service types available in SSH on the C4. |
| UnknownState | INTEGER { known(0), unknown(1) } | current | Similar to TMN representation of the Unknown Status. |
| VlanId | Integer32 (1..1000000) | current | The unique identifier for a Virtual LAN. A value of 1000000 indicates unknown VLAN. |