CAMBIUM-PTP250-MIB
123 objects
MIB for PTP250
Imported Objects
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | enterprises Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.17713 | Identitycambium | MIB for PTP250 | ||
| 1.3.6.1.4.1.17713.1 | Nodeptp | |||
| 1.3.6.1.4.1.17713.2 | Nodeptmp | |||
| 1.3.6.1.4.1.17713.250 | Nodeptp250 | |||
| 1.3.6.1.4.1.17713.250.1 | Nodeconfiguration | |||
| 1.3.6.1.4.1.17713.250.1.1 | ScalariPAddress | read-only | current | Internet protocol (IP) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. |
| 1.3.6.1.4.1.17713.250.1.2 | ScalarsubnetMask | read-only | current | A subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnettin… |
| 1.3.6.1.4.1.17713.250.1.3 | ScalargatewayIPAddress | read-only | current | The IP address of a computer on the current network that is currently acting as a network gateway. A gateway acts as an entrance / exit to packets from / to ot… |
| 1.3.6.1.4.1.17713.250.1.4 | ScalarremoteMACAddress | read-only | current | MAC address of the PTP wireless unit forming the other end of the PTP link |
| 1.3.6.1.4.1.17713.250.1.5 | ScalarmasterSlaveMode | read-only | current | The PTP wireless link operates using a master and slave relationship |
| 1.3.6.1.4.1.17713.250.1.6 | ScalarmaximumTransmitPower | read-only | current | Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link |
| 1.3.6.1.4.1.17713.250.1.7 | ScalarantennaGain | read-only | current | Antenna Gain. Expressed in 10ths of dBi. NB: This attribute is ignored for variants with an integral antenna. |
| 1.3.6.1.4.1.17713.250.1.8 | ScalarcableLoss | read-only | current | Loss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna. |
| 1.3.6.1.4.1.17713.250.1.9 | ScalarchannelBandwidth | read-only | current | The selected bandwidth of the transmit and receive radio channels |
| 1.3.6.1.4.1.17713.250.1.10 | ScalarremoteIPAddress | read-only | current | IP Address of the peer wireless unit |
| 1.3.6.1.4.1.17713.250.1.11 | ScalarlinkName | read-only | current | Name of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOT… |
| 1.3.6.1.4.1.17713.250.1.12 | ScalarsiteName | read-only | current | This field contains a user-provided description of the site name together with any additional notes |
| 1.3.6.1.4.1.17713.250.1.13 | ScalarconfiguredModulationMode | read-only | current | The fixed modulation mode or maximum adaptive modulation mode to be used by the wireless link |
| 1.3.6.1.4.1.17713.250.1.14 | Scalarband | read-only | current | The frequency band to be used by the wireless link |
| 1.3.6.1.4.1.17713.250.1.15 | ScalarconfiguredRange | read-only | current | Configured distance between the two peer wireless units expressed in hundredths of a kilometer. |
| 1.3.6.1.4.1.17713.250.1.16 | ScalarchannelSelection | read-only | current | The channels selected for use by the user. The current channel will be selected from this list. |
| 1.3.6.1.4.1.17713.250.1.17 | ScalarvlanTagging | read-only | current | Whether or not to use VLAN tagging for management. |
| 1.3.6.1.4.1.17713.250.1.18 | ScalarvlanId | read-only | current | VLAN ID for management. |
| 1.3.6.1.4.1.17713.250.1.19 | ScalarvlanPriority | read-only | current | VLAN priority for management. |
| 1.3.6.1.4.1.17713.250.1.22 | ScalarfixedModMode | read-only | current | If disabled, allows automatic modulation mode selection. |
| 1.3.6.1.4.1.17713.250.1.23 | ScalardualPayload | read-only | current | If enabled, allows dual payload modulation modes to be selected. |
| 1.3.6.1.4.1.17713.250.2 | Nodeethernet | |||
| 1.3.6.1.4.1.17713.250.2.1 | ScalardataPortAutoNegotiation | read-only | current | This controls whether the local Ethernet interface configuration is automatically negotiated or forced. |
| 1.3.6.1.4.1.17713.250.2.2 | ScalardataPortAutoNegAdvertisement | read-only | current | This sets the different Ethernet configurations that will be advertised during auto negotiation. |
| 1.3.6.1.4.1.17713.250.2.3 | ScalardataPortStatus | read-only | current | Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.250.2.4 | ScalardataPortSpeedAndDuplex | read-only | current | The current speed and duplex of the Ethernet link |
| 1.3.6.1.4.1.17713.250.3 | Nodelicence | |||
| 1.3.6.1.4.1.17713.250.3.1 | ScalarregionCode | read-only | current | The region code prohibits the wireless unit from operating outside the regulated limits. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.250.3.2 | ScalarproductVariant | read-only | current | The product variant |
| 1.3.6.1.4.1.17713.250.3.3 | ScalarproductName | read-only | current | Name of the product variant |
| 1.3.6.1.4.1.17713.250.4 | Nodemanagement | |||
| 1.3.6.1.4.1.17713.250.4.1 | ScalarinstallArmState | read-only | current | Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.250.4.2 | ScalartFTPServerIPAddress | read-only | current | IP address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved |
| 1.3.6.1.4.1.17713.250.4.3 | ScalartFTPServerPortNumber | read-only | current | The port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved |
| 1.3.6.1.4.1.17713.250.4.4 | ScalartFTPSoftwareUpgradeFileName | read-only | current | Filename of the Software Upgrade to be loaded from the TFTP Server |
| 1.3.6.1.4.1.17713.250.4.5 | ScalartFTPSoftwareUpgradeStatus | read-only | current | The current status of the TFTP Software upgrade process |
| 1.3.6.1.4.1.17713.250.4.6 | ScalartFTPSoftwareUpgradeStatusText | read-only | current | Descriptive text describing the status of the TFTP Software upgrade process, including any error details |
| 1.3.6.1.4.1.17713.250.4.7 | ScalartFTPSoftwareUpgradeStatusAdditionalText | read-only | current | Any additional text describing the status of the TFTP Software upgrade process, including any error details |
| 1.3.6.1.4.1.17713.250.5 | NodephyStatus | |||
| 1.3.6.1.4.1.17713.250.5.1 | ScalarreceivePower | read-only | current | Receive power expressed in tenths of a dBm |
| 1.3.6.1.4.1.17713.250.5.2 | ScalarvectorError | read-only | current | The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude.… |
| 1.3.6.1.4.1.17713.250.5.3 | ScalartransmitPower | read-only | current | Transmit power expressed in tenths of a dBm |
| 1.3.6.1.4.1.17713.250.5.5 | ScalarlinkLoss | read-only | current | The wireless link loss expressed in tenths of a dB |
| 1.3.6.1.4.1.17713.250.5.6 | ScalarcurrentChannel | read-only | current | Current active channel |
| 1.3.6.1.4.1.17713.250.5.7 | ScalarextendedChannel | read-only | current | Current extended channel in 40MHz mode |
| 1.3.6.1.4.1.17713.250.5.8 | ScalarreceiveModulationMode | read-only | current | Current active receive modulation mode |
| 1.3.6.1.4.1.17713.250.5.9 | ScalartransmitModulationMode | read-only | current | Current active transmit modulation mode |
| 1.3.6.1.4.1.17713.250.5.11 | ScalarcurrentFreqMHz | read-only | current | Current channel frequency expressed in integer MHz |
| 1.3.6.1.4.1.17713.250.5.12 | ScalarextendedFreqMHz | read-only | current | Extended channel frequency expressed in integer MHz |
| 1.3.6.1.4.1.17713.250.5.13 | ScalarsignalStrengthRatio | read-only | current | Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of … |
| 1.3.6.1.4.1.17713.250.5.14 | ScalarsearchState | read-only | current | Search status of the wireless unit. 'Registering' means that the unit has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wire… |
| 1.3.6.1.4.1.17713.250.5.15 | ScalarnoiseFloor | read-only | current | Noise floor expressed in tenths of a dBm |
| 1.3.6.1.4.1.17713.250.5.16 | ScalarradarDetectChannel | accessible-for-notify | current | Channel on which Radar has been detected. (Note that this variable is accessible-for-notify only). |
| 1.3.6.1.4.1.17713.250.5.17 | ScalarmeasuredRange | read-only | current | Measured distance between the two peer wireless units expressed in tenths of Km. |
| 1.3.6.1.4.1.17713.250.6 | Nodealarms | |||
| 1.3.6.1.4.1.17713.250.6.1 | ScalarnoWirelessChannelAvailable | read-only | current | Spectrum Management was unable to locate a suitable wireless channel to operate on |
| 1.3.6.1.4.1.17713.250.7 | Nodesmtp | |||
| 1.3.6.1.4.1.17713.250.7.1 | ScalarsMTPServerIPAddress | read-only | current | IP address of the SMTP server |
| 1.3.6.1.4.1.17713.250.7.2 | ScalarsMTPServerPortNumber | read-only | current | Port number of the SMTP server |
| 1.3.6.1.4.1.17713.250.7.3 | ScalarsMTPSourceEmailAddress | read-only | current | The 'from' email address used when constructing the automatically generated e-mail message |
| 1.3.6.1.4.1.17713.250.7.4 | ScalarsMTPDestinationEmailAddress | read-only | current | The 'to' email address used when constructing the automatically generated e-mail message |
| 1.3.6.1.4.1.17713.250.7.5 | ScalarsMTPEnabledMessages | read-only | current | This controls which SMTP messages the unit will send |
| 1.3.6.1.4.1.17713.250.8 | NodesnmpControl | |||
| 1.3.6.1.4.1.17713.250.8.1 | ScalarsNMPCommunityTableNumber | read-only | current | Number of entries in the sNMPCommunityTable. |
| 1.3.6.1.4.1.17713.250.8.2 | TablesNMPCommunityTable | not-accessible | current | SNMP community string configuration table. |
| 1.3.6.1.4.1.17713.250.8.2.1 | RowsNMPCommunityTableEntry | not-accessible | current | Table SNMPCommunityTable |
| 1.3.6.1.4.1.17713.250.8.2.1.1 | ColumnsNMPCommunityTableIndex | not-accessible | current | SNMP community value, used to index the SNMPCommunityTable. |
| 1.3.6.1.4.1.17713.250.8.2.1.2 | ColumnsNMPCommunityString | read-only | current | The community string for this entry |
| 1.3.6.1.4.1.17713.250.8.2.1.3 | ColumnsNMPCommunityAccess | read-only | current | Whether this community allows read-only or read-write access |
| 1.3.6.1.4.1.17713.250.8.2.1.4 | ColumnsNMPCommunityOid | read-only | current | The OID at which the root of this community's subtree starts |
| 1.3.6.1.4.1.17713.250.8.3 | ScalarsNMPTrapTableNumber | read-only | current | Number of entries in the sNMPTrapTable. |
| 1.3.6.1.4.1.17713.250.8.4 | TablesNMPTrapTable | not-accessible | current | SNMP trap configuration table. |
| 1.3.6.1.4.1.17713.250.8.4.1 | RowsNMPTrapTableEntry | not-accessible | current | Table SNMPTrapTable |
| 1.3.6.1.4.1.17713.250.8.4.1.1 | ColumnsNMPTrapTableIndex | not-accessible | current | SNMP trap value, used to index the SNMPTrapTable. |
| 1.3.6.1.4.1.17713.250.8.4.1.2 | ColumnsNMPTrapIPAddress | read-only | current | The IP address to which all SNMP Traps are sent. |
| 1.3.6.1.4.1.17713.250.8.4.1.3 | ColumnsNMPTrapPortNumber | read-only | current | Destination port for SNMP Traps (default=162). A value of 0 will disable the trap receiver. |
| 1.3.6.1.4.1.17713.250.8.4.1.4 | ColumnsNMPTrapCommunity | read-only | current | The community string for this trap entry |
| 1.3.6.1.4.1.17713.250.8.4.1.5 | ColumnsNMPTrapVersion | read-only | current | The SNMP protocol version for this trap entry |
| 1.3.6.1.4.1.17713.250.8.6 | ScalarsNMPEnabledTraps | read-only | current | This controls which SNMP Traps the unit will send |
| 1.3.6.1.4.1.17713.250.9 | Nodentp | |||
| 1.3.6.1.4.1.17713.250.9.1 | ScalarnTPState | read-only | current | NTP control state |
| 1.3.6.1.4.1.17713.250.9.2 | ScalarnTPPollInterval | read-only | current | The NTP server polling interval |
| 1.3.6.1.4.1.17713.250.9.3 | ScalarnTPSync | read-only | current | If NTP Sync fails then check the server settings in the Remote Management page, or disable NTP |
| 1.3.6.1.4.1.17713.250.9.4 | ScalarnTPLastSync | read-only | current | Last NTP sync time |
| 1.3.6.1.4.1.17713.250.9.5 | ScalarsystemClock | read-only | current | System clock presented as local time |
| 1.3.6.1.4.1.17713.250.9.6 | ScalartimeZone | read-only | current | Time zone offsets from Greenwich Mean Time (GMT) |
| 1.3.6.1.4.1.17713.250.9.7 | ScalarnTPServerIp | read-only | current | Specifies the NTP server IP address. |
| 1.3.6.1.4.1.17713.250.9.8 | ScalarnTPServerPortNumber | read-only | current | Port number of the NTP server |
| 1.3.6.1.4.1.17713.250.10 | Nodeversions | |||
| 1.3.6.1.4.1.17713.250.10.1 | ScalarsoftwareVersion | read-only | current | Current software version |
| 1.3.6.1.4.1.17713.250.10.2 | ScalarhardwareVersion | read-only | current | Hardware platform version |
| 1.3.6.1.4.1.17713.250.10.3 | ScalarbootVersion | read-only | current | Boot code software version |
| 1.3.6.1.4.1.17713.250.11 | NodepubStats | |||
| 1.3.6.1.4.1.17713.250.11.1 | ScalarreceiveDataRate | read-only | current | Average data rate over the last one second interval (tenths of Mbps) |
| 1.3.6.1.4.1.17713.250.11.2 | ScalartransmitDataRate | read-only | current | Average data rate over the last one second interval (tenths of Mbps) |
| 1.3.6.1.4.1.17713.250.11.3 | ScalaraggregateDataRate | read-only | current | Average data rate over the last one second interval (tenths of Mbps) |
| 1.3.6.1.4.1.17713.250.11.4 | ScalarwirelessLinkStatus | read-only | current | Current status of the wireless link |
| 1.3.6.1.4.1.17713.250.97 | ComplianceptpCompliance | current | The compliance statement for the Cambium Networks PTP MIB | |
| 1.3.6.1.4.1.17713.250.98 | NodeptpGroups | |||
| 1.3.6.1.4.1.17713.250.98.5 | GroupconfigurationGroup | current | The configuration object group. | |
| 1.3.6.1.4.1.17713.250.98.6 | GroupethernetGroup | current | The ethernet object group. | |
| 1.3.6.1.4.1.17713.250.98.8 | GrouplicenceGroup | current | The licence object group. | |
| 1.3.6.1.4.1.17713.250.98.9 | GroupmanagementGroup | current | The management object group. | |
| 1.3.6.1.4.1.17713.250.98.12 | GroupphyStatusGroup | current | The phyStatus object group. | |
| 1.3.6.1.4.1.17713.250.98.13 | GroupalarmsGroup | current | The alarms object group. | |
| 1.3.6.1.4.1.17713.250.98.15 | GroupsmtpGroup | current | The smtp object group. | |
| 1.3.6.1.4.1.17713.250.98.16 | GroupsnmpControlGroup | current | The snmpControl object group. | |
| 1.3.6.1.4.1.17713.250.98.17 | GroupntpGroup | current | The ntp object group. | |
| 1.3.6.1.4.1.17713.250.98.19 | GroupversionsGroup | current | The versions object group. | |
| 1.3.6.1.4.1.17713.250.98.20 | GrouppubStatsGroup | current | The pubStats object group. | |
| 1.3.6.1.4.1.17713.250.98.99 | GroupnotificationsGroup | current | The notifications group. | |
| 1.3.6.1.4.1.17713.250.99 | NodeptpTraps | |||
| 1.3.6.1.4.1.17713.250.99.0 | NodeptpTrapPrefix | |||
| 1.3.6.1.4.1.17713.250.99.0.1 | NotificationdataPortStatusTrap | current | Status of the Ethernet link has changed. | |
| 1.3.6.1.4.1.17713.250.99.0.2 | NotificationinstallArmStateTrap | current | Unit install arm state has changed | |
| 1.3.6.1.4.1.17713.250.99.0.3 | NotificationnoWirelessChannelAvailableTrap | current | Wireless channel availability has changed | |
| 1.3.6.1.4.1.17713.250.99.0.4 | NotificationlinkStatusTrap | current | Wireless link status has changed | |
| 1.3.6.1.4.1.17713.250.99.0.5 | NotificationradarDetectTrap | current | Radar has been detected on one or more channels |