CAMBIUM-PTP500-MIB
221 objects
MIB for 105Mbps non-line-of-sight (NLOS) wireless ethernet bridge.
Imported Objects
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | enterprises Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.17713 | Identitycambium | MIB for 105Mbps non-line-of-sight (NLOS) wireless ethernet bridge. | ||
| 1.3.6.1.4.1.17713.1 | Nodeptp | |||
| 1.3.6.1.4.1.17713.2 | Nodeptmp | |||
| 1.3.6.1.4.1.17713.5 | Nodeptp500 | |||
| 1.3.6.1.4.1.17713.5.3 | Nodedfs | |||
| 1.3.6.1.4.1.17713.5.3.1 | ScalardfsTableNumber | read-only | current | Number of entries in the dfsTable |
| 1.3.6.1.4.1.17713.5.3.2 | TabledfsTable | not-accessible | current | A table storing a snapshot of various DFS measurements for each channel |
| 1.3.6.1.4.1.17713.5.3.2.1 | RowdfsTableEntry | not-accessible | current | Table DfsTable |
| 1.3.6.1.4.1.17713.5.3.2.1.1 | ColumndfsTableIndex | not-accessible | current | used to index values in the dfsTable. |
| 1.3.6.1.4.1.17713.5.3.2.1.2 | ColumndfsMeans | read-only | current | Snapshot of DFS means |
| 1.3.6.1.4.1.17713.5.3.2.1.3 | ColumndfsNineNinePointNinePercentiles | read-only | current | Snapshot of DFS 99.9 percentiles |
| 1.3.6.1.4.1.17713.5.3.2.1.4 | ColumndfsPeaks | read-only | current | Snapshot of DFS peaks |
| 1.3.6.1.4.1.17713.5.5 | Nodeconfiguration | |||
| 1.3.6.1.4.1.17713.5.5.1 | ScalariPAddress | read-write | current | Internet protocol (IP) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. NB: A system reboot is req… |
| 1.3.6.1.4.1.17713.5.5.2 | ScalarsubnetMask | read-write | current | A subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnettin… |
| 1.3.6.1.4.1.17713.5.5.3 | ScalargatewayIPAddress | read-write | current | The IP address of a computer on the current network that is currently acting as a network gateway. A gateway acts as an entrance / exit to packets from / to ot… |
| 1.3.6.1.4.1.17713.5.5.4 | ScalartargetMACAddress | read-only | current | MAC address of the PTP wireless unit forming the other end of the PTP link |
| 1.3.6.1.4.1.17713.5.5.5 | ScalarmasterSlaveMode | read-only | current | The PTP wireless link operates using a master and slave relationship |
| 1.3.6.1.4.1.17713.5.5.6 | ScalarmaximumTransmitPower | read-only | current | Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link |
| 1.3.6.1.4.1.17713.5.5.7 | ScalarantennaGain | read-write | current | Antenna Gain. Expressed in 10ths of dBi. NB: This attribute is ignored for variants with an integral antenna. |
| 1.3.6.1.4.1.17713.5.5.8 | ScalarcableLoss | read-write | current | Loss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna. |
| 1.3.6.1.4.1.17713.5.5.9 | ScalareIRP | read-only | current | Effective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBm |
| 1.3.6.1.4.1.17713.5.5.11 | ScalarchannelBandwidth | read-only | current | This control sets the bandwidth of the transmit and receive radio channels |
| 1.3.6.1.4.1.17713.5.5.12 | ScalarremoteIPAddress | read-only | current | IP Address of the peer wireless unit |
| 1.3.6.1.4.1.17713.5.5.14 | ScalarlinkName | read-only | current | Name of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOT… |
| 1.3.6.1.4.1.17713.5.5.15 | ScalarsiteName | read-write | current | This field contains a user-provided description of the site name together with any additional notes |
| 1.3.6.1.4.1.17713.5.5.16 | ScalaraccessMethod | read-only | current | This controls whether the link can be established between pre-paired Master-Slave using MAC addresses (Link Access) or by using link name (Link Name Access) |
| 1.3.6.1.4.1.17713.5.5.17 | ScalargroupID | read-only | current | When Access Method is set to Group Access, the Group ID identifies all the units belonging to the same group. Group Access is only supported on some platforms |
| 1.3.6.1.4.1.17713.5.6 | Nodeethernet | |||
| 1.3.6.1.4.1.17713.5.6.1 | ScalardataPortAutoNegotiation | read-write | current | This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiat… |
| 1.3.6.1.4.1.17713.5.6.2 | ScalardataPortAutoNegAdvertisement | read-write | current | This sets the different Ethernet configurations that will be advertised during auto negotiation. NB: The new setting will only take effect after a system reboo… |
| 1.3.6.1.4.1.17713.5.6.3 | ScalardataPortAutoMdix | read-write | current | This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot |
| 1.3.6.1.4.1.17713.5.6.4 | ScalardataPortStatus | read-only | current | Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.5.6.5 | ScalardataPortSpeedAndDuplex | read-only | current | The current speed and duplex of the Ethernet link |
| 1.3.6.1.4.1.17713.5.6.6 | ScalardataPortWirelessDownAlert | read-write | current | When enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect tha… |
| 1.3.6.1.4.1.17713.5.6.7 | ScalaruseVLANForManagementInterfaces | read-write | current | This controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system reboot |
| 1.3.6.1.4.1.17713.5.6.8 | ScalarvLANManagementPriority | read-write | current | This VLAN Priority (0-7) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system reboot |
| 1.3.6.1.4.1.17713.5.6.11 | ScalarvLANManagementVID | read-write | current | This VLAN VID (0-4094) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system reboot |
| 1.3.6.1.4.1.17713.5.6.14 | ScalarvLANPriorityTableNumber | read-only | current | Number of entries in the vLANPriorityTable. |
| 1.3.6.1.4.1.17713.5.6.15 | TablevLANPriorityTable | not-accessible | current | A priority queue mapping table. This is a list of packet queues indexed by VLAN priority. |
| 1.3.6.1.4.1.17713.5.6.15.1 | RowvLANPriorityTableEntry | not-accessible | current | Table VLANPriorityTable |
| 1.3.6.1.4.1.17713.5.6.15.1.1 | ColumnvLANPriorityQueueMapping | read-write | current | Mapping of VLAN priority flag to packet queue. The higher the queue number the greater its priority. |
| 1.3.6.1.4.1.17713.5.6.15.1.2 | ColumnvLANPriorityTableIndex | not-accessible | current | VLAN priority flag, used to index values in the vLANPriorityTable. |
| 1.3.6.1.4.1.17713.5.7 | Nodetelecom | |||
| 1.3.6.1.4.1.17713.5.7.1 | ScalartelecomsInterface | read-only | current | The line interface type. If this is set to 'None' then the telecoms interfaces are disabled, and the telecom group attributes will be ignored. |
| 1.3.6.1.4.1.17713.5.7.2 | ScalartelecomsChannelStatus | read-only | current | Current status of telecoms channel. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.5.7.4 | ScalartelecomsLineCode | read-only | current | The line code setting of the telecoms interface. This must match the setting of the device connected to this interface |
| 1.3.6.1.4.1.17713.5.7.6 | ScalartelecomsCableLength | read-only | current | The length of the cable connected to the telecoms interface, measured in feet |
| 1.3.6.1.4.1.17713.5.7.8 | ScalartelecomsLoopback | read-only | current | The loopback status of telecoms channel. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a … |
| 1.3.6.1.4.1.17713.5.8 | Nodelicence | |||
| 1.3.6.1.4.1.17713.5.8.1 | ScalarregionCode | read-only | current | The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted licence key. NB: a change… |
| 1.3.6.1.4.1.17713.5.8.2 | ScalarproductVariant | read-only | current | The product variant |
| 1.3.6.1.4.1.17713.5.8.3 | ScalarproductName | read-only | current | Name of the product variant |
| 1.3.6.1.4.1.17713.5.8.4 | ScalarethernetFiberSupport | read-only | current | Ethernet fiber support availability on this wireless unit |
| 1.3.6.1.4.1.17713.5.8.5 | ScalarfrequencyVariant | read-only | current | Frequency variant of the wireless unit |
| 1.3.6.1.4.1.17713.5.8.6 | ScalarbandwidthVariant | read-only | current | Bandwidth variant of the wireless unit |
| 1.3.6.1.4.1.17713.5.8.7 | ScalarconstantPowerSpectralDensity | read-only | current | Constant power spectral density mode control |
| 1.3.6.1.4.1.17713.5.8.9 | ScalarsNMPv3Enable | read-only | current | SNMPv3 availability control |
| 1.3.6.1.4.1.17713.5.8.11 | ScalarlicensedCapacity | read-only | current | Maximum allowable data rate for ethernet frames permitted by the licence key. The actual data rate depends upon the prevailing wireless conditions |
| 1.3.6.1.4.1.17713.5.9 | Nodemanagement | |||
| 1.3.6.1.4.1.17713.5.9.3 | ScalarinstallStatus | read-only | current | A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because un… |
| 1.3.6.1.4.1.17713.5.9.4 | ScalarinstallArmState | read-only | current | Indicates if the unit is being installed. NB: a value other than 'disarmed' on startup, or a change of state during operation may generate an SNMP trap and/or … |
| 1.3.6.1.4.1.17713.5.9.5 | ScalartFTPServerIPAddress | read-write | current | IP address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved |
| 1.3.6.1.4.1.17713.5.9.6 | ScalartFTPServerPortNumber | read-write | current | The port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved |
| 1.3.6.1.4.1.17713.5.9.7 | ScalartFTPSoftwareUpgradeFileName | read-write | current | Filename of the Software Upgrade to be loaded from the TFTP Server |
| 1.3.6.1.4.1.17713.5.9.8 | ScalartFTPStartSoftwareUpgrade | read-write | current | Write '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished |
| 1.3.6.1.4.1.17713.5.9.9 | ScalartFTPSoftwareUpgradeStatus | read-only | current | The current status of the TFTP Software upgrade process |
| 1.3.6.1.4.1.17713.5.9.10 | ScalartFTPSoftwareUpgradeStatusText | read-only | current | Descriptive text describing the status of the TFTP Software upgrade process, including any error details |
| 1.3.6.1.4.1.17713.5.9.11 | ScalartFTPSoftwareUpgradeStatusAdditionalText | read-only | current | Any additional text describing the status of the TFTP Software upgrade process, including any error details |
| 1.3.6.1.4.1.17713.5.9.12 | ScalarhTTPAccessEnabled | read-write | current | This controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote manag… |
| 1.3.6.1.4.1.17713.5.9.13 | ScalartelnetAccessEnabled | read-write | current | This controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any chan… |
| 1.3.6.1.4.1.17713.5.9.14 | ScalarhTTPPortNumber | read-write | current | This controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit… |
| 1.3.6.1.4.1.17713.5.9.15 | ScalarhTTPSPortNumber | read-write | current | This controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the Licence Key. Any … |
| 1.3.6.1.4.1.17713.5.9.16 | ScalartelnetPortNumber | read-write | current | This controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the un… |
| 1.3.6.1.4.1.17713.5.9.17 | ScalarhTTPSAccessEnabled | read-write | current | This controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote man… |
| 1.3.6.1.4.1.17713.5.10 | NodephyControl | |||
| 1.3.6.1.4.1.17713.5.10.1 | ScalarlinkSymmetry | read-only | current | In fixed asymmetric mode (3 to 1) the transmit time is three times as long as the receive time. In fixed symmetric mode (1 to 1) the unit spends an equal amoun… |
| 1.3.6.1.4.1.17713.5.10.2 | ScalarlinkModeOptimisation | read-only | current | Optimises the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimise transmission errors by automa… |
| 1.3.6.1.4.1.17713.5.10.3 | ScalaruserConfiguredMaxModulationMode | read-write | current | The maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation ag… |
| 1.3.6.1.4.1.17713.5.10.4 | ScalarremoteMaximumTransmitPower | read-only | current | Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link |
| 1.3.6.1.4.1.17713.5.12 | NodephyStatus | |||
| 1.3.6.1.4.1.17713.5.12.1 | ScalarreceivePower | read-only | current | Receive power expressed in tenths of a dBm |
| 1.3.6.1.4.1.17713.5.12.2 | ScalarvectorError | read-only | current | The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude.… |
| 1.3.6.1.4.1.17713.5.12.3 | ScalartransmitPower | read-only | current | Transmit power expressed in tenths of a dBm |
| 1.3.6.1.4.1.17713.5.12.4 | Scalarrange | read-only | current | Distance between the two peer wireless units expressed in tenths of a kilometer |
| 1.3.6.1.4.1.17713.5.12.5 | ScalarlinkLoss | read-only | current | The wireless link loss expressed in tenths of a dB |
| 1.3.6.1.4.1.17713.5.12.6 | ScalarreceiveChannel | read-only | current | Current active receive channel |
| 1.3.6.1.4.1.17713.5.12.7 | ScalartransmitChannel | read-only | current | Current active transmit channel |
| 1.3.6.1.4.1.17713.5.12.8 | ScalarreceiveModulationMode | read-only | current | Current active receive modulation mode |
| 1.3.6.1.4.1.17713.5.12.9 | ScalartransmitModulationMode | read-only | current | Current active transmit modulation mode |
| 1.3.6.1.4.1.17713.5.12.11 | ScalarreceiveFreqMHz | read-only | current | Current receive frequency expressed in integer MHz |
| 1.3.6.1.4.1.17713.5.12.12 | ScalartransmitFreqMHz | read-only | current | Current transmit frequency expressed in integer MHz |
| 1.3.6.1.4.1.17713.5.12.13 | ScalarsignalStrengthRatio | read-only | current | Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of … |
| 1.3.6.1.4.1.17713.5.12.14 | ScalarreceiveFreqKHz | read-only | current | Current receive frequency expressed as KHz |
| 1.3.6.1.4.1.17713.5.12.15 | ScalartransmitFreqKHz | read-only | current | Current transmit frequency expressed as KHz |
| 1.3.6.1.4.1.17713.5.12.16 | ScalarsearchState | read-only | current | Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wi… |
| 1.3.6.1.4.1.17713.5.13 | Nodealarms | |||
| 1.3.6.1.4.1.17713.5.13.1 | ScalarunitOutOfCalibration | read-only | current | The unit is out of calibration |
| 1.3.6.1.4.1.17713.5.13.4 | ScalarincompatibleRegionCodes | read-only | current | The master and slave units have incompatible region codes. NB: Both units must have compatible licence keys |
| 1.3.6.1.4.1.17713.5.13.5 | ScalarnoWirelessChannelAvailable | read-only | current | Spectrum Management was unable to locate a suitable wireless channel to operate on |
| 1.3.6.1.4.1.17713.5.13.6 | ScalarwirelessLinkDisabledWarning | read-only | current | The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic |
| 1.3.6.1.4.1.17713.5.13.7 | ScalardataPortDisabledWarning | read-only | current | The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic |
| 1.3.6.1.4.1.17713.5.13.9 | ScalardataPortConfigurationMismatch | read-only | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch |
| 1.3.6.1.4.1.17713.5.13.10 | ScalarincompatibleMasterAndSlave | read-only | current | A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusua… |
| 1.3.6.1.4.1.17713.5.13.11 | ScalartDDSynchronizationStatus | read-only | current | An alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing… |
| 1.3.6.1.4.1.17713.5.13.13 | ScalartDDSynchronizationAlarm | read-only | current | Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this lin… |
| 1.3.6.1.4.1.17713.5.13.14 | ScalarlinkModeOptimizationMismatch | read-only | current | The remote node of this link has been configured with a different link mode optimization |
| 1.3.6.1.4.1.17713.5.13.16 | ScalarcapacityLicenseMismatch | read-only | current | The local and remote units have different licensed capacity and/or the full capacity trial has been activated at only one unit. The wireless link is operating … |
| 1.3.6.1.4.1.17713.5.15 | Nodesmtp | |||
| 1.3.6.1.4.1.17713.5.15.1 | ScalarsMTPEmailAlert | read-write | current | Simple Mail Transfer Protocol is used to send equipment alerts via email to a specified email address. This utility can only be configured by the system admini… |
| 1.3.6.1.4.1.17713.5.15.2 | ScalarsMTPServerIPAddress | read-write | current | IP address of the SMTP server |
| 1.3.6.1.4.1.17713.5.15.3 | ScalarsMTPServerPortNumber | read-write | current | Port number of the SMTP server |
| 1.3.6.1.4.1.17713.5.15.4 | ScalarsMTPSourceEmailAddress | read-write | current | The 'from' email address used when constructing the automatically generated e-mail message |
| 1.3.6.1.4.1.17713.5.15.5 | ScalarsMTPDestinationEmailAddress | read-write | current | The 'to' email address used when constructing the automatically generated e-mail message |
| 1.3.6.1.4.1.17713.5.15.6 | ScalarsMTPEnabledMessages | read-write | current | This controls which SMTP messages the unit will send |
| 1.3.6.1.4.1.17713.5.16 | NodesnmpControl | |||
| 1.3.6.1.4.1.17713.5.16.1 | ScalarsNMPPortNumber | read-write | current | The IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attribute |
| 1.3.6.1.4.1.17713.5.16.2 | ScalarsNMPCommunityString | read-write | current | The SNMP community string. NB: A system reboot is required to activate changes to this attribute |
| 1.3.6.1.4.1.17713.5.16.3 | ScalarsNMPTrapTableNumber | read-only | current | Number of entries in the sNMPTrapTable. |
| 1.3.6.1.4.1.17713.5.16.4 | TablesNMPTrapTable | not-accessible | current | SNMP trap configuration table. |
| 1.3.6.1.4.1.17713.5.16.4.1 | RowsNMPTrapTableEntry | not-accessible | current | Table SNMPTrapTable |
| 1.3.6.1.4.1.17713.5.16.4.1.1 | ColumnsNMPTrapTableIndex | not-accessible | current | SNMP trap value, used to index the SNMPTrapTable. |
| 1.3.6.1.4.1.17713.5.16.4.1.2 | ColumnsNMPTrapIPAddress | read-write | current | The IP address to which all SNMP Traps are sent. An IP Address of 0.0.0.0 disables all TRAP generation. NB: A system reboot is required to activate changes to … |
| 1.3.6.1.4.1.17713.5.16.4.1.3 | ColumnsNMPTrapPortNumber | read-write | current | Destination port for SNMP Traps (default=162). A value of 0 will disable the trap receiver. NB: A system reboot is required to activate changes to this attribu… |
| 1.3.6.1.4.1.17713.5.16.5 | ScalarsNMPTrapVersion | read-write | current | The SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attribute |
| 1.3.6.1.4.1.17713.5.16.6 | ScalarsNMPEnabledTraps | read-write | current | This controls which SNMP Traps the unit will send |
| 1.3.6.1.4.1.17713.5.16.7 | ScalarenabledDiagnosticAlarms | read-write | current | Controls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by… |
| 1.3.6.1.4.1.17713.5.16.8 | ScalarsNMPSendAllTrapsAtStartup | read-write | current | Controls whether cleared traps are reported at start-up as well as raised traps. Only enabled traps will be reported. NB: Traps corresponding to transient even… |
| 1.3.6.1.4.1.17713.5.17 | Nodesntp | |||
| 1.3.6.1.4.1.17713.5.17.1 | ScalarsNTPState | read-write | current | SNTP control state |
| 1.3.6.1.4.1.17713.5.17.2 | ScalarsNTPServerIPAddress | read-write | current | The IP address of a valid SNTP server |
| 1.3.6.1.4.1.17713.5.17.3 | ScalarsNTPServerPortNumber | read-write | current | The IP port number of the SNTP server. Defaults to port 123. |
| 1.3.6.1.4.1.17713.5.17.4 | ScalarsNTPPollInterval | read-write | current | The SNTP server polling interval |
| 1.3.6.1.4.1.17713.5.17.5 | ScalarsNTPSync | read-only | current | If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP. NB: a change of state may generate an SNMP trap and/or SMTP e… |
| 1.3.6.1.4.1.17713.5.17.6 | ScalarsNTPLastSync | read-only | current | Last SNTP sync time |
| 1.3.6.1.4.1.17713.5.17.7 | ScalarsystemClock | read-only | current | System clock presented as local time |
| 1.3.6.1.4.1.17713.5.17.8 | ScalartimeZone | read-write | current | Time zone offsets from Greenwich Mean Time (GMT) |
| 1.3.6.1.4.1.17713.5.17.9 | ScalardaylightSaving | read-write | current | Daylight Saving Time |
| 1.3.6.1.4.1.17713.5.18 | Nodereset | |||
| 1.3.6.1.4.1.17713.5.18.1 | ScalarsystemReset | read-write | current | Setting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memory |
| 1.3.6.1.4.1.17713.5.19 | Nodeversions | |||
| 1.3.6.1.4.1.17713.5.19.1 | ScalarsoftwareVersion | read-only | current | Current software version |
| 1.3.6.1.4.1.17713.5.19.2 | ScalarhardwareVersion | read-only | current | Hardware platform version |
| 1.3.6.1.4.1.17713.5.19.3 | ScalarsecondarySoftwareVersion | read-only | current | Secondary software version, used when the primary software image is invalid or erased |
| 1.3.6.1.4.1.17713.5.19.4 | ScalarbootVersion | read-only | current | Boot code software version |
| 1.3.6.1.4.1.17713.5.20 | NodepubStats | |||
| 1.3.6.1.4.1.17713.5.20.1 | ScalarreceiveDataRate | read-only | current | Average data rate over the last one second interval (kbps) |
| 1.3.6.1.4.1.17713.5.20.2 | ScalartransmitDataRate | read-only | current | Average data rate over the last one second interval (kbps) |
| 1.3.6.1.4.1.17713.5.20.3 | ScalaraggregateDataRate | read-only | current | Average data rate over the last one second interval (kbps) |
| 1.3.6.1.4.1.17713.5.20.4 | ScalarwirelessLinkAvailability | read-only | current | Link availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision |
| 1.3.6.1.4.1.17713.5.20.5 | ScalarwirelessLinkStatus | read-only | current | Current status of the wireless link |
| 1.3.6.1.4.1.17713.5.20.6 | ScalarbyteErrorRatio | read-only | current | Reciprocal of the byte error ratio calculated since the last reset of the system counters |
| 1.3.6.1.4.1.17713.5.20.7 | ScalarreceiveModulationModeDetail | read-only | current | The reason for the current receive modulation mode |
| 1.3.6.1.4.1.17713.5.22 | Nodeencryption | |||
| 1.3.6.1.4.1.17713.5.22.1 | ScalarencryptionAlgorithm | read-only | current | The Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm mu… |
| 1.3.6.1.4.1.17713.5.23 | NodetDDControl | |||
| 1.3.6.1.4.1.17713.5.23.1 | ScalartDDSynchronizationMode | read-only | current | TDD Synchronization Mode selection |
| 1.3.6.1.4.1.17713.5.24 | NodesyslogControl | |||
| 1.3.6.1.4.1.17713.5.24.1 | ScalarsyslogClient | read-only | current | Enable or disable the syslog client |
| 1.3.6.1.4.1.17713.5.24.2 | ScalarsyslogState | read-only | current | The syslog service has been enabled or disabled |
| 1.3.6.1.4.1.17713.5.25 | NodeaAAControl | |||
| 1.3.6.1.4.1.17713.5.25.1 | ScalaruserTableNumber | read-only | current | Number of entries in the userTable |
| 1.3.6.1.4.1.17713.5.25.2 | TableuserTable | not-accessible | current | The User Table Control group contains objects specifically for user account management. |
| 1.3.6.1.4.1.17713.5.25.2.1 | RowuserTableEntry | not-accessible | current | Table UserTable |
| 1.3.6.1.4.1.17713.5.25.2.1.1 | ColumnuserTableIndex | not-accessible | current | used to index values in the userTable. |
| 1.3.6.1.4.1.17713.5.25.2.1.2 | ColumnuserName | read-only | current | User name which must be entered, along with the appropriate password, in order to gain access to the system. |
| 1.3.6.1.4.1.17713.5.25.2.1.3 | ColumnuserRole | read-only | current | Role of the selected user. A Security Officer has access to and can modify all settings. A System Administrator has access to and can modify all non-security s… |
| 1.3.6.1.4.1.17713.5.25.2.1.4 | ColumnuserEnabled | read-only | current | Enable / Disable the selected user |
| 1.3.6.1.4.1.17713.5.25.2.1.5 | ColumnuserPassword | read-write | current | User password, which must be entered in order to gain access to the system. |
| 1.3.6.1.4.1.17713.5.96 | Nodesupplementary | |||
| 1.3.6.1.4.1.17713.5.96.1 | Scalarlongitude | read-write | current | The longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function. |
| 1.3.6.1.4.1.17713.5.96.2 | Scalarlatitude | read-write | current | The latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function. |
| 1.3.6.1.4.1.17713.5.96.3 | Scalaraltitude | read-write | current | The altitude of the unit, measured in metres. This object is set by the SNMP manager and has no internal function. |
| 1.3.6.1.4.1.17713.5.97 | ComplianceptpCompliance | current | The compliance statement for the Cambium PTP MIB | |
| 1.3.6.1.4.1.17713.5.98 | NodeptpGroups | |||
| 1.3.6.1.4.1.17713.5.98.3 | GroupdfsGroup | current | The dfs object group. | |
| 1.3.6.1.4.1.17713.5.98.5 | GroupconfigurationGroup | current | The configuration object group. | |
| 1.3.6.1.4.1.17713.5.98.6 | GroupethernetGroup | current | The ethernet object group. | |
| 1.3.6.1.4.1.17713.5.98.7 | GrouptelecomGroup | current | The telecom object group. | |
| 1.3.6.1.4.1.17713.5.98.8 | GrouplicenceGroup | current | The licence object group. | |
| 1.3.6.1.4.1.17713.5.98.9 | GroupmanagementGroup | current | The management object group. | |
| 1.3.6.1.4.1.17713.5.98.10 | GroupphyControlGroup | current | The phyControl object group. | |
| 1.3.6.1.4.1.17713.5.98.12 | GroupphyStatusGroup | current | The phyStatus object group. | |
| 1.3.6.1.4.1.17713.5.98.13 | GroupalarmsGroup | current | The alarms object group. | |
| 1.3.6.1.4.1.17713.5.98.15 | GroupsmtpGroup | current | The smtp object group. | |
| 1.3.6.1.4.1.17713.5.98.16 | GroupsnmpControlGroup | current | The snmpControl object group. | |
| 1.3.6.1.4.1.17713.5.98.17 | GroupsntpGroup | current | The sntp object group. | |
| 1.3.6.1.4.1.17713.5.98.18 | GroupresetGroup | current | The reset object group. | |
| 1.3.6.1.4.1.17713.5.98.19 | GroupversionsGroup | current | The versions object group. | |
| 1.3.6.1.4.1.17713.5.98.20 | GrouppubStatsGroup | current | The pubStats object group. | |
| 1.3.6.1.4.1.17713.5.98.22 | GroupencryptionGroup | current | The encryption object group. | |
| 1.3.6.1.4.1.17713.5.98.23 | GrouptDDControlGroup | current | The tDDControl object group. | |
| 1.3.6.1.4.1.17713.5.98.24 | GroupsyslogControlGroup | current | The syslogControl object group. | |
| 1.3.6.1.4.1.17713.5.98.25 | GroupaAAControlGroup | current | The aAAControl object group. | |
| 1.3.6.1.4.1.17713.5.98.96 | GroupsupplementaryGroup | current | The supplementary object group. | |
| 1.3.6.1.4.1.17713.5.98.99 | GroupnotificationsGroup | current | The notifications group. | |
| 1.3.6.1.4.1.17713.5.99 | NodeptpTraps | |||
| 1.3.6.1.4.1.17713.5.99.0 | NodeptpTrapPrefix | |||
| 1.3.6.1.4.1.17713.5.99.0.1 | NotificationchannelChangeTrap | current | The PTP radio has changed wireless channel. This has been caused by either i) mandatory radar avoidance, a DFS impulsive interference event will also be detect… | |
| 1.3.6.1.4.1.17713.5.99.0.2 | NotificationdfsImpulsiveInterferenceTrap | current | DFS impulsive interference detected event | |
| 1.3.6.1.4.1.17713.5.99.0.3 | NotificationdataPortStatusTrap | current | Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert | |
| 1.3.6.1.4.1.17713.5.99.0.4 | NotificationtelecomsChannelStatusTrap | current | Current status of telecoms channel. NB: a change of state may generate an SNMP trap and/or SMTP email alert | |
| 1.3.6.1.4.1.17713.5.99.0.6 | NotificationtelecomsLoopbackTrap | current | The loopback status of telecoms channel. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a … | |
| 1.3.6.1.4.1.17713.5.99.0.8 | NotificationregionCodeTrap | current | The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted licence key. NB: a change… | |
| 1.3.6.1.4.1.17713.5.99.0.9 | NotificationinstallStatusTrap | current | A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because un… | |
| 1.3.6.1.4.1.17713.5.99.0.10 | NotificationinstallArmStateTrap | current | Indicates if the unit is being installed. NB: a value other than 'disarmed' on startup, or a change of state during operation may generate an SNMP trap and/or … | |
| 1.3.6.1.4.1.17713.5.99.0.11 | NotificationunitOutOfCalibrationTrap | current | The unit is out of calibration | |
| 1.3.6.1.4.1.17713.5.99.0.14 | NotificationincompatibleRegionCodesTrap | current | The master and slave units have incompatible region codes. NB: Both units must have compatible licence keys | |
| 1.3.6.1.4.1.17713.5.99.0.15 | NotificationnoWirelessChannelAvailableTrap | current | Spectrum Management was unable to locate a suitable wireless channel to operate on | |
| 1.3.6.1.4.1.17713.5.99.0.16 | NotificationwirelessLinkDisabledWarningTrap | current | The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic | |
| 1.3.6.1.4.1.17713.5.99.0.17 | NotificationdataPortDisabledWarningTrap | current | The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic | |
| 1.3.6.1.4.1.17713.5.99.0.19 | NotificationdataPortConfigurationMismatchTrap | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch | |
| 1.3.6.1.4.1.17713.5.99.0.20 | NotificationincompatibleMasterAndSlaveTrap | current | A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusua… | |
| 1.3.6.1.4.1.17713.5.99.0.21 | NotificationsNTPSyncTrap | current | If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP. NB: a change of state may generate an SNMP trap and/or SMTP e… | |
| 1.3.6.1.4.1.17713.5.99.0.22 | NotificationtDDSynchronizationAlarmTrap | current | Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this lin… | |
| 1.3.6.1.4.1.17713.5.99.0.25 | NotificationlinkModeOptimizationMismatchTrap | current | The remote node of this link has been configured with a different link mode optimization | |
| 1.3.6.1.4.1.17713.5.99.0.27 | NotificationcapacityLicenseMismatchTrap | current | The local and remote units have different licensed capacity and/or the full capacity trial has been activated at only one unit. The wireless link is operating … | |
| 1.3.6.1.4.1.17713.5.99.0.30 | NotificationsyslogStateTrap | current | The syslog service has been enabled or disabled | |
| 1.3.6.1.4.1.17713.5.99.0.31 | NotificationsyslogLocalNearlyFullTrap | current | The syslog local log is nearly full (90%) | |
| 1.3.6.1.4.1.17713.5.99.0.32 | NotificationsyslogLocalWrappedTrap | current | The syslog local log has wrapped | |
| 1.3.6.1.4.1.17713.5.99.0.33 | NotificationsyslogClientTrap | current | Enable or disable the syslog client |