CAMBIUM-PTP600-MIB
298 objects
MIB for 300Mbps non-line-of-sight (NLOS) wireless ethernet bridge.
Imported Objects
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | enterprises Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.17713 | Identitycambium | MIB for 300Mbps non-line-of-sight (NLOS) wireless ethernet bridge. | ||
| 1.3.6.1.4.1.17713.1 | Nodeptp | |||
| 1.3.6.1.4.1.17713.2 | Nodeptmp | |||
| 1.3.6.1.4.1.17713.6 | Nodeptp600 | |||
| 1.3.6.1.4.1.17713.6.3 | Nodedfs | |||
| 1.3.6.1.4.1.17713.6.3.1 | ScalardfsTableNumber | read-only | current | Number of entries in the dfsTable |
| 1.3.6.1.4.1.17713.6.3.2 | TabledfsTable | not-accessible | current | A table storing a snapshot of various DFS measurements for each channel |
| 1.3.6.1.4.1.17713.6.3.2.1 | RowdfsTableEntry | not-accessible | current | Table DfsTable |
| 1.3.6.1.4.1.17713.6.3.2.1.1 | ColumndfsTableIndex | not-accessible | current | used to index values in the dfsTable. |
| 1.3.6.1.4.1.17713.6.3.2.1.2 | ColumndfsMeans | read-only | current | Snapshot of DFS means |
| 1.3.6.1.4.1.17713.6.3.2.1.3 | ColumndfsNineNinePointNinePercentiles | read-only | current | Snapshot of DFS 99.9 percentiles |
| 1.3.6.1.4.1.17713.6.3.2.1.4 | ColumndfsPeaks | read-only | current | Snapshot of DFS peaks |
| 1.3.6.1.4.1.17713.6.4 | Nodebridge | |||
| 1.3.6.1.4.1.17713.6.4.1 | ScalarlocalPacketFiltering | read-write | current | When Local Packet Filtering is Enabled, the bridge learns the source MAC addresses of devices transmitting Ethernet packets on the local Ethernet network, and … |
| 1.3.6.1.4.1.17713.6.5 | Nodeconfiguration | |||
| 1.3.6.1.4.1.17713.6.5.1 | ScalariPv4Address | read-write | current | Internet protocol (IPv4) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. NB: A system reboot is r… |
| 1.3.6.1.4.1.17713.6.5.2 | ScalarsubnetMask | read-write | current | A subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnettin… |
| 1.3.6.1.4.1.17713.6.5.3 | ScalargatewayIPAddress | read-write | current | The IPv4 address of a computer on the current network that is currently acting as an IPv4 network gateway. A gateway acts as an entrance / exit to packets from… |
| 1.3.6.1.4.1.17713.6.5.4 | ScalartargetMACAddress | read-only | current | MAC address of the PTP wireless unit forming the other end of the PTP link |
| 1.3.6.1.4.1.17713.6.5.5 | ScalarmasterSlaveMode | read-write | current | The PTP wireless link operates using a master and slave relationship |
| 1.3.6.1.4.1.17713.6.5.6 | ScalarmaximumTransmitPower | read-only | current | Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link |
| 1.3.6.1.4.1.17713.6.5.7 | ScalarantennaGain | read-write | current | Antenna Gain. Expressed in 10ths of dBi. NB: This attribute is ignored for variants with an integral antenna. |
| 1.3.6.1.4.1.17713.6.5.8 | ScalarcableLoss | read-write | current | Loss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna. |
| 1.3.6.1.4.1.17713.6.5.9 | ScalareIRP | read-only | current | Effective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBm |
| 1.3.6.1.4.1.17713.6.5.10 | ScalarethernetCappedMaxWirelessSpeed | read-write | current | Ethernet frames will be discarded in the ODU if the data rate over the wireless link exceeds the Ethernet link speed at the local or remote Data port. The Ethe… |
| 1.3.6.1.4.1.17713.6.5.11 | ScalarchannelBandwidth | read-only | current | This control sets the bandwidth of the transmit and receive radio channels |
| 1.3.6.1.4.1.17713.6.5.12 | ScalarremoteIPAddress | read-only | current | IP Address of the peer wireless unit |
| 1.3.6.1.4.1.17713.6.5.14 | ScalarlinkName | read-write | current | Name of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOT… |
| 1.3.6.1.4.1.17713.6.5.15 | ScalarsiteName | read-write | current | This field contains a user-provided description of the site name together with any additional notes |
| 1.3.6.1.4.1.17713.6.5.16 | ScalaraccessMethod | read-only | current | ODUs must be configured in pairs before a link can be established. The Access Method attribute determines how the paired ODUs will recognise each other. For th… |
| 1.3.6.1.4.1.17713.6.5.17 | ScalargroupID | read-write | current | When Access Method is set to Group Access, the Group ID identifies all the units belonging to the same group |
| 1.3.6.1.4.1.17713.6.5.18 | ScalariPv6Address | read-write | current | Internet protocol (IPv6) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. NB: A system reboot is r… |
| 1.3.6.1.4.1.17713.6.5.20 | ScalariPVersion | read-write | current | IP protocol selection. Choice of IPv4, IPv6 or Dual. |
| 1.3.6.1.4.1.17713.6.5.21 | ScalariPv6AutoConfiguredLinkLocalAddress | read-only | current | The auto configured link local IPv6 address |
| 1.3.6.1.4.1.17713.6.5.22 | ScalariPv6PrefixLength | read-write | current | IPv6 prefix length |
| 1.3.6.1.4.1.17713.6.5.23 | ScalariPv6GatewayAddress | read-write | current | The IPv6 address of a computer on the current network that is currently acting as an IPv6 network gateway. A gateway acts as an entrance / exit to packets from… |
| 1.3.6.1.4.1.17713.6.5.24 | ScalarremoteInternetAddressType | read-only | current | The type of Internet address specified by the associated remoteInternetAddressType. |
| 1.3.6.1.4.1.17713.6.5.25 | ScalarremoteInternetAddress | read-only | current | INET address used to identify the peer wireless unit |
| 1.3.6.1.4.1.17713.6.6 | Nodeethernet | |||
| 1.3.6.1.4.1.17713.6.6.1 | ScalardataPortAutoNegotiation | read-write | current | This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiat… |
| 1.3.6.1.4.1.17713.6.6.2 | ScalardataPortAutoNegAdvertisement | read-write | current | This sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system rebo… |
| 1.3.6.1.4.1.17713.6.6.3 | ScalardataPortAutoMdix | read-write | current | This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot |
| 1.3.6.1.4.1.17713.6.6.4 | ScalardataPortStatus | read-only | current | Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.6.6.5 | ScalardataPortSpeedAndDuplex | read-only | current | The current speed and duplex of the Ethernet link |
| 1.3.6.1.4.1.17713.6.6.6 | ScalardataPortWirelessDownAlert | read-write | current | When enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect tha… |
| 1.3.6.1.4.1.17713.6.6.7 | ScalaruseVLANForManagementInterfaces | read-write | current | This controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system reboot |
| 1.3.6.1.4.1.17713.6.6.8 | ScalarvLANManagementPriority | read-write | current | This VLAN Priority (0-7) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system reboot |
| 1.3.6.1.4.1.17713.6.6.11 | ScalarvLANManagementVID | read-write | current | This VLAN VID (0-4094) will be included in packets generated by the management interfaces. Note the new setting will only take effect after a system reboot |
| 1.3.6.1.4.1.17713.6.6.12 | ScalarmanagementPortStatus | read-only | current | Current status of the out-of-band management link. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.6.6.13 | ScalarmanagementPortSpeedAndDuplex | read-only | current | The current speed and duplex of the out-of-band management link |
| 1.3.6.1.4.1.17713.6.6.14 | ScalarethernetPriorityTableNumber | read-only | current | Number of entries in the vLANPriorityTable. |
| 1.3.6.1.4.1.17713.6.6.15 | TableethernetPriorityTable | not-accessible | current | A priority queue mapping table. This is a list of packet queues indexed by Ethernet priority. |
| 1.3.6.1.4.1.17713.6.6.15.1 | RowethernetPriorityTableEntry | not-accessible | current | Table EthernetPriorityTable |
| 1.3.6.1.4.1.17713.6.6.15.1.1 | ColumnethernetPriorityTableIndex | not-accessible | current | Ethernet priority flag, used to index values in the ethernetPriorityTable |
| 1.3.6.1.4.1.17713.6.6.15.1.2 | ColumnethernetPriorityQueueMapping | read-write | current | Configures the classification of this Ethernet priority (also known as IEEE 802.1p value) to an egress queue at the wireless port |
| 1.3.6.1.4.1.17713.6.6.16 | Scalarl2CPPriorityTableNumber | read-only | current | Number of entries in the l2CPPriorityTable. |
| 1.3.6.1.4.1.17713.6.6.17 | Tablel2CPPriorityTable | not-accessible | current | A priority queue mapping table. This is a list of packet queues indexed by L2CP priority. |
| 1.3.6.1.4.1.17713.6.6.17.1 | Rowl2CPPriorityTableEntry | not-accessible | current | Table L2CPPriorityTable |
| 1.3.6.1.4.1.17713.6.6.17.1.1 | Columnl2CPPriorityTableIndex | not-accessible | current | L2CP priority flag, used to index values in the l2CPPriorityTable |
| 1.3.6.1.4.1.17713.6.6.17.1.2 | Columnl2CPPriorityQueueMapping | read-write | current | Configures the classification of this layer two control protocol (L2CP) to an egress queue at the wireless port |
| 1.3.6.1.4.1.17713.6.6.18 | ScalariPDSCPPriorityTableNumber | read-only | current | Number of entries in the iPDSCPPriorityTable. |
| 1.3.6.1.4.1.17713.6.6.19 | TableiPDSCPPriorityTable | not-accessible | current | A priority queue mapping table. This is a list of packet queues indexed by L3 IP DSCP priority. |
| 1.3.6.1.4.1.17713.6.6.19.1 | RowiPDSCPPriorityTableEntry | not-accessible | current | Table IPDSCPPriorityTable |
| 1.3.6.1.4.1.17713.6.6.19.1.1 | ColumniPDSCPPriorityTableIndex | not-accessible | current | IP DSCP priority flag, used to index values in the iPDSCPPriorityTable |
| 1.3.6.1.4.1.17713.6.6.19.1.2 | ColumniPDSCPPriorityQueueMapping | read-write | current | Configures the classification of this IP differentiated services code point (DSCP) value to an egress queue at the wireless port |
| 1.3.6.1.4.1.17713.6.6.20 | ScalarmPLSTCPriorityTableNumber | read-only | current | Number of entries in the mPLSTCPriorityTable. |
| 1.3.6.1.4.1.17713.6.6.21 | TablemPLSTCPriorityTable | not-accessible | current | A priority queue mapping table. This is a list of priority queues indexed by MPLS TC priority. |
| 1.3.6.1.4.1.17713.6.6.21.1 | RowmPLSTCPriorityTableEntry | not-accessible | current | Table MPLSTCPriorityTable |
| 1.3.6.1.4.1.17713.6.6.21.1.1 | ColumnmPLSTCPriorityTableIndex | not-accessible | current | MPLS TC priority flag, used to index values in the mPLSTCPriorityTable |
| 1.3.6.1.4.1.17713.6.6.21.1.2 | ColumnmPLSTCPriorityQueueMapping | read-write | current | Configures the classification of this MPLS traffic class (the field formerly known as EXP) to an egress queue at the wireless port |
| 1.3.6.1.4.1.17713.6.6.22 | ScalarmanagementMode | read-only | current | Out-of-Band Management (only available on certain hardware models): End-to-end out-of-band mode in which the management agent can be reached from the managemen… |
| 1.3.6.1.4.1.17713.6.6.23 | ScalarmanagementPortWirelessDownAlert | read-only | current | When enabled, this causes the management link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect t… |
| 1.3.6.1.4.1.17713.6.6.24 | ScalarqOSPriorityScheme | read-write | current | Selects classification based on fields in the Ethernet header (Layer 2) or in the Network header (Layer 3). The unit recognises two network layer protocols: IP… |
| 1.3.6.1.4.1.17713.6.6.25 | ScalarunknownNetworkPriorityQueueMapping | read-write | current | Configures the classification of unknown network protocols to an egress queue at the wireless port. Unknown means something other than IP and MPLS |
| 1.3.6.1.4.1.17713.6.6.26 | ScalardSCPManagementPriority | read-only | current | This Differentiated Services Code Point value will be inserted in the IP Header of all IP Datagrams transmitted by the management interfaces |
| 1.3.6.1.4.1.17713.6.6.27 | ScalarethernetBridgingStatus | read-only | current | Current status of Ethernet packet bridging over the wireless link |
| 1.3.6.1.4.1.17713.6.7 | Nodetelecom | |||
| 1.3.6.1.4.1.17713.6.7.1 | ScalartelecomsInterface | read-only | current | The line interface type. If this is set to 'None' then the telecoms interfaces are disabled, and the telecom group attributes will be ignored. |
| 1.3.6.1.4.1.17713.6.7.2 | ScalartelecomsChannelAStatus | read-only | current | Current status of telecoms channel A. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.6.7.3 | ScalartelecomsChannelBStatus | read-only | current | Current status of telecoms channel B. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.6.7.4 | ScalarchannelALineCode | read-only | current | The line code setting of the telecoms interface. This must match the setting of the device connected to this interface |
| 1.3.6.1.4.1.17713.6.7.5 | ScalarchannelBLineCode | read-only | current | The line code setting of the telecoms interface. This must match the setting of the device connected to this interface |
| 1.3.6.1.4.1.17713.6.7.6 | ScalarchannelACableLength | read-only | current | The length of the cable connected to the telecoms interface, measured in feet |
| 1.3.6.1.4.1.17713.6.7.7 | ScalarchannelBCableLength | read-only | current | The length of the cable connected to the telecoms interface, measured in feet |
| 1.3.6.1.4.1.17713.6.7.8 | ScalarchannelALoopback | read-only | current | The loopback status of telecoms channel A. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to … |
| 1.3.6.1.4.1.17713.6.7.9 | ScalarchannelBLoopback | read-only | current | The loopback status of telecoms channel B. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to … |
| 1.3.6.1.4.1.17713.6.7.10 | ScalartelecomsChannelSelection | read-only | current | Indicates which telecoms channels have been enabled. If only Channel A has been enabled, then the Channel B attributes will be ignored. |
| 1.3.6.1.4.1.17713.6.8 | Nodelicence | |||
| 1.3.6.1.4.1.17713.6.8.1 | ScalarregionCode | read-only | current | The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted license key. NB: a change… |
| 1.3.6.1.4.1.17713.6.8.2 | ScalarproductVariant | read-only | current | The product variant |
| 1.3.6.1.4.1.17713.6.8.3 | ScalarproductName | read-only | current | Name of the product variant |
| 1.3.6.1.4.1.17713.6.8.4 | ScalarethernetFiberSupport | read-only | current | Ethernet fiber support availability on this wireless unit |
| 1.3.6.1.4.1.17713.6.8.5 | ScalarfrequencyVariant | read-only | current | Frequency variant of the wireless unit |
| 1.3.6.1.4.1.17713.6.8.6 | ScalarbandwidthVariant | read-only | current | Bandwidth variant of the wireless unit |
| 1.3.6.1.4.1.17713.6.8.7 | ScalarconstantPowerSpectralDensity | read-only | current | Constant power spectral density mode control |
| 1.3.6.1.4.1.17713.6.8.9 | ScalarsNMPv3Enable | read-only | current | SNMPv3 availability control |
| 1.3.6.1.4.1.17713.6.8.10 | ScalarhAZLOCConfiguration | read-only | current | The HAZLOC/ATEX Configuration of this unit. The Gas Group is configured by the license key. |
| 1.3.6.1.4.1.17713.6.8.11 | ScalarsecurityLevel | read-only | current | The maximum configurable security level |
| 1.3.6.1.4.1.17713.6.9 | Nodemanagement | |||
| 1.3.6.1.4.1.17713.6.9.1 | ScalartargetRange | read-only | current | Initial target range used in installation +/-1, expressed in tenths of a kilometer. When Auto-Ranging this must be set to 0 |
| 1.3.6.1.4.1.17713.6.9.2 | ScalarrangingMode | read-only | current | Type of ranging to use during installation, either Auto-Ranging or use a selectable Target Range |
| 1.3.6.1.4.1.17713.6.9.3 | ScalarinstallStatus | read-only | current | A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because un… |
| 1.3.6.1.4.1.17713.6.9.4 | ScalarinstallArmState | read-only | current | Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.6.9.5 | ScalartFTPServerIPAddress | read-write | current | IP address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved |
| 1.3.6.1.4.1.17713.6.9.6 | ScalartFTPServerPortNumber | read-write | current | The port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved |
| 1.3.6.1.4.1.17713.6.9.7 | ScalartFTPSoftwareUpgradeFileName | read-write | current | Filename of the Software Upgrade to be loaded from the TFTP Server |
| 1.3.6.1.4.1.17713.6.9.8 | ScalartFTPStartSoftwareUpgrade | read-write | current | Write '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished. Continuing with… |
| 1.3.6.1.4.1.17713.6.9.9 | ScalartFTPSoftwareUpgradeStatus | read-only | current | The current status of the TFTP Software upgrade process |
| 1.3.6.1.4.1.17713.6.9.10 | ScalartFTPSoftwareUpgradeStatusText | read-only | current | Descriptive text describing the status of the TFTP Software upgrade process, including any error details |
| 1.3.6.1.4.1.17713.6.9.11 | ScalartFTPSoftwareUpgradeStatusAdditionalText | read-only | current | Any additional text describing the status of the TFTP Software upgrade process, including any error details |
| 1.3.6.1.4.1.17713.6.9.12 | ScalarhTTPAccessEnabled | read-write | current | This controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote manag… |
| 1.3.6.1.4.1.17713.6.9.13 | ScalartelnetAccessEnabled | read-write | current | This controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any chan… |
| 1.3.6.1.4.1.17713.6.9.14 | ScalarhTTPPortNumber | read-write | current | This controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit… |
| 1.3.6.1.4.1.17713.6.9.15 | ScalarhTTPSPortNumber | read-write | current | This controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the License Key. Any … |
| 1.3.6.1.4.1.17713.6.9.16 | ScalartelnetPortNumber | read-write | current | This controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the un… |
| 1.3.6.1.4.1.17713.6.9.17 | ScalarhTTPSAccessEnabled | read-write | current | This controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote man… |
| 1.3.6.1.4.1.17713.6.9.18 | ScalartFTPServerInternetAddressType | read-only | current | The type of Internet address specified by the associated tFTPServerInternetAddress. |
| 1.3.6.1.4.1.17713.6.9.19 | ScalartFTPServerInternetAddress | read-write | current | INET address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved |
| 1.3.6.1.4.1.17713.6.10 | NodephyControl | |||
| 1.3.6.1.4.1.17713.6.10.1 | ScalarlinkSymmetry | read-only | current | Link Symmetry: in fixed symmetric mode the master spends an equal amount of time transmitting and receiving; in fixed asymmetric modes the master transmit and … |
| 1.3.6.1.4.1.17713.6.10.2 | ScalarlinkModeOptimisation | read-only | current | Optimises the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimise transmission errors by automa… |
| 1.3.6.1.4.1.17713.6.10.3 | ScalaruserConfiguredMaxModulationMode | read-write | current | The maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation ag… |
| 1.3.6.1.4.1.17713.6.10.4 | ScalarremoteMaximumTransmitPower | read-only | current | Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link |
| 1.3.6.1.4.1.17713.6.10.5 | ScalartxColorCode | read-only | current | Transmit Color Code. This attribute need only be considered when the unit is installed in a network of PTP600 units and where some of the units are operating o… |
| 1.3.6.1.4.1.17713.6.10.6 | ScalarrxColorCode | read-only | current | Receive Color Code. This attribute need only be considered when the unit is installed in a network of PTP600 units and where some of the units are operating on… |
| 1.3.6.1.4.1.17713.6.10.8 | ScalarautomaticTxPowerControl | read-only | current | When enabled, the transmit power of the local end is automatically adjusted to maintain a configurable target receive signal level at the remote end of the lin… |
| 1.3.6.1.4.1.17713.6.10.9 | ScalarremoteRxTargetPower | read-only | current | This is the target receive level for the end of the link which is remote from the end being configured. When Automatic Power Control is enabled, the transmit p… |
| 1.3.6.1.4.1.17713.6.12 | NodephyStatus | |||
| 1.3.6.1.4.1.17713.6.12.1 | ScalarreceivePower | read-only | current | Receive power expressed in tenths of a dBm |
| 1.3.6.1.4.1.17713.6.12.2 | ScalarvectorError | read-only | current | The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude.… |
| 1.3.6.1.4.1.17713.6.12.3 | ScalartransmitPower | read-only | current | Transmit power expressed in tenths of a dBm |
| 1.3.6.1.4.1.17713.6.12.4 | Scalarrange | read-only | current | Distance between the two peer wireless units expressed in tenths of a kilometer |
| 1.3.6.1.4.1.17713.6.12.5 | ScalarlinkLoss | read-only | current | The wireless link loss expressed in tenths of a dB |
| 1.3.6.1.4.1.17713.6.12.6 | ScalarreceiveChannel | read-only | current | Current active receive channel |
| 1.3.6.1.4.1.17713.6.12.7 | ScalartransmitChannel | read-only | current | Current active transmit channel |
| 1.3.6.1.4.1.17713.6.12.8 | ScalarreceiveModulationMode | read-only | current | Current active receive modulation mode |
| 1.3.6.1.4.1.17713.6.12.9 | ScalartransmitModulationMode | read-only | current | Current active transmit modulation mode |
| 1.3.6.1.4.1.17713.6.12.11 | ScalarreceiveFreqMHz | read-only | current | Current receive frequency expressed in integer MHz |
| 1.3.6.1.4.1.17713.6.12.12 | ScalartransmitFreqMHz | read-only | current | Current transmit frequency expressed in integer MHz |
| 1.3.6.1.4.1.17713.6.12.13 | ScalarsignalStrengthRatio | read-only | current | Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of … |
| 1.3.6.1.4.1.17713.6.12.14 | ScalarreceiveFreqKHz | read-only | current | Current receive frequency expressed as KHz |
| 1.3.6.1.4.1.17713.6.12.15 | ScalartransmitFreqKHz | read-only | current | Current transmit frequency expressed as KHz |
| 1.3.6.1.4.1.17713.6.12.16 | ScalarsearchState | read-only | current | Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wi… |
| 1.3.6.1.4.1.17713.6.12.17 | ScalarrawReceivePower | read-only | current | Raw receive power expressed in tenths of a dBm |
| 1.3.6.1.4.1.17713.6.13 | Nodealarms | |||
| 1.3.6.1.4.1.17713.6.13.1 | ScalarunitOutOfCalibration | read-only | current | The unit is out of calibration |
| 1.3.6.1.4.1.17713.6.13.4 | ScalarincompatibleRegionCodes | read-only | current | The master and slave units have incompatible region codes. NB: Both units must have compatible license keys |
| 1.3.6.1.4.1.17713.6.13.5 | ScalarnoWirelessChannelAvailable | read-only | current | Spectrum Management was unable to locate a suitable wireless channel to operate on |
| 1.3.6.1.4.1.17713.6.13.6 | ScalarwirelessLinkDisabledWarning | read-only | current | The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic |
| 1.3.6.1.4.1.17713.6.13.7 | ScalardataPortDisabledWarning | read-only | current | The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic |
| 1.3.6.1.4.1.17713.6.13.8 | ScalardataPortFiberStatus | read-only | current | If the fiber link is not OK, there are three possible causes: Either the fiber link has been installed but disabled (because the license key does not include f… |
| 1.3.6.1.4.1.17713.6.13.9 | ScalardataPortConfigurationMismatch | read-only | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch |
| 1.3.6.1.4.1.17713.6.13.10 | ScalarincompatibleMasterAndSlave | read-only | current | A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusua… |
| 1.3.6.1.4.1.17713.6.13.11 | ScalartDDSynchronizationStatus | read-only | current | An alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing… |
| 1.3.6.1.4.1.17713.6.13.12 | ScalarmanagementPortDisabledWarning | read-only | current | The SNMP ifAdminStatus of the out-of-band management interface has disabled Ethernet traffic |
| 1.3.6.1.4.1.17713.6.13.13 | ScalartDDSynchronizationAlarm | read-only | current | Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this lin… |
| 1.3.6.1.4.1.17713.6.13.14 | ScalarlinkModeOptimizationMismatch | read-only | current | The remote node of this link has been configured with a different link mode optimization |
| 1.3.6.1.4.1.17713.6.13.15 | ScalarmanagementPortConfigurationMismatch | read-only | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. Th… |
| 1.3.6.1.4.1.17713.6.13.16 | ScalarsecureModeAlarm | read-only | current | The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, … |
| 1.3.6.1.4.1.17713.6.13.17 | ScalarethernetBridgingStatusAlarm | read-only | current | Ethernet traffic bridging is disabled because the wireless link is not operating at the configured Lowest Ethernet Modulation Mode |
| 1.3.6.1.4.1.17713.6.15 | Nodesmtp | |||
| 1.3.6.1.4.1.17713.6.15.1 | ScalarsMTPEmailAlert | read-write | current | Simple Mail Transfer Protocol is used to send equipment alerts via email to a specified email address |
| 1.3.6.1.4.1.17713.6.15.2 | ScalarsMTPServerIPAddress | read-write | current | IP address of the SMTP server |
| 1.3.6.1.4.1.17713.6.15.3 | ScalarsMTPServerPortNumber | read-write | current | Port number of the SMTP server |
| 1.3.6.1.4.1.17713.6.15.4 | ScalarsMTPSourceEmailAddress | read-write | current | The 'from' email address used when constructing the automatically generated e-mail message |
| 1.3.6.1.4.1.17713.6.15.5 | ScalarsMTPDestinationEmailAddress | read-write | current | The 'to' email address used when constructing the automatically generated e-mail message |
| 1.3.6.1.4.1.17713.6.15.6 | ScalarsMTPEnabledMessages | read-write | current | This controls which SMTP messages the unit will send |
| 1.3.6.1.4.1.17713.6.15.7 | ScalarsMTPServerInternetAddressType | read-only | current | The type of Internet address specified by the associated sMTPServerInternetAddress. |
| 1.3.6.1.4.1.17713.6.15.8 | ScalarsMTPServerInternetAddress | read-write | current | Internet address of the SMTP server |
| 1.3.6.1.4.1.17713.6.16 | NodesnmpControl | |||
| 1.3.6.1.4.1.17713.6.16.1 | ScalarsNMPPortNumber | read-write | current | The IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attribute |
| 1.3.6.1.4.1.17713.6.16.2 | ScalarsNMPCommunityString | read-write | current | The SNMP community string. NB: A system reboot is required to activate changes to this attribute |
| 1.3.6.1.4.1.17713.6.16.3 | ScalarsNMPTrapTableNumber | read-only | current | Number of entries in the sNMPTrapTable. |
| 1.3.6.1.4.1.17713.6.16.4 | TablesNMPTrapTable | not-accessible | current | SNMP trap configuration table. |
| 1.3.6.1.4.1.17713.6.16.4.1 | RowsNMPTrapTableEntry | not-accessible | current | Table SNMPTrapTable |
| 1.3.6.1.4.1.17713.6.16.4.1.1 | ColumnsNMPTrapTableIndex | not-accessible | current | SNMP trap value, used to index the SNMPTrapTable. |
| 1.3.6.1.4.1.17713.6.16.4.1.2 | ColumnsNMPTrapIPAddress | read-write | current | The IP address to which all SNMP Traps are sent. NB: A system reboot is required to activate changes to this attribute. |
| 1.3.6.1.4.1.17713.6.16.4.1.3 | ColumnsNMPTrapPortNumber | read-write | current | Destination port for SNMP Traps (default=162). NB: A system reboot is required to activate changes to this attribute. |
| 1.3.6.1.4.1.17713.6.16.4.1.4 | ColumnsNMPTrapInternetAddressType | read-only | current | The type of Internet address specified by the associated sNMPTrapInternetAddress. |
| 1.3.6.1.4.1.17713.6.16.4.1.5 | ColumnsNMPTrapInternetAddress | read-write | current | The Internet address to which all SNMP Traps are sent. |
| 1.3.6.1.4.1.17713.6.16.4.1.6 | ColumnsNMPTrapReceiverEnabled | read-write | current | A value of 0 disables the sending of SNMP trap to corresponding receiver. A value of 1 enables the sending of SNMP trap to corresponding receiver. |
| 1.3.6.1.4.1.17713.6.16.5 | ScalarsNMPTrapVersion | read-write | current | The SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attribute |
| 1.3.6.1.4.1.17713.6.16.6 | ScalarsNMPEnabledTraps | read-write | current | This controls which SNMP Traps the unit will send |
| 1.3.6.1.4.1.17713.6.16.7 | ScalarenabledDiagnosticAlarms | read-write | current | Controls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by… |
| 1.3.6.1.4.1.17713.6.16.8 | ScalarsNMPSendAllTrapsAtStartup | read-write | current | Controls whether or not all the enabled traps and alarms (including cleared alarms) are reported at start-up. |
| 1.3.6.1.4.1.17713.6.17 | Nodesntp | |||
| 1.3.6.1.4.1.17713.6.17.1 | ScalarsNTPState | read-write | current | SNTP control state |
| 1.3.6.1.4.1.17713.6.17.4 | ScalarsNTPPollInterval | read-write | current | The SNTP server polling interval |
| 1.3.6.1.4.1.17713.6.17.5 | ScalarsNTPSync | read-only | current | If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP |
| 1.3.6.1.4.1.17713.6.17.6 | ScalarsNTPLastSync | read-only | current | Last SNTP sync time |
| 1.3.6.1.4.1.17713.6.17.7 | ScalarsystemClock | read-only | current | System clock presented as local time |
| 1.3.6.1.4.1.17713.6.17.8 | ScalartimeZone | read-write | current | Time zone offsets from Greenwich Mean Time (GMT) |
| 1.3.6.1.4.1.17713.6.17.9 | ScalardaylightSaving | read-write | current | Daylight Saving Time |
| 1.3.6.1.4.1.17713.6.17.10 | ScalarsNTPPrimaryServer | read-write | current | Specifies the primary SNTP server, determining the order in which the servers are tried. |
| 1.3.6.1.4.1.17713.6.17.11 | ScalarsNTPPrimaryServerDeadTime | read-write | current | Time (in seconds) to wait before retrying communications with an unresponsive primary SNTP server. Setting the value to 0 disables the timer. |
| 1.3.6.1.4.1.17713.6.17.12 | ScalarsNTPServerRetries | read-write | current | Number of times the PTP will retry after an SNTP server fails to respond. |
| 1.3.6.1.4.1.17713.6.17.13 | ScalarsNTPServerTimeout | read-write | current | Time (in seconds) the PTP will wait for a response from an SNTP server. |
| 1.3.6.1.4.1.17713.6.17.14 | ScalarsNTPServerTableNumber | read-only | current | Number of entries in the SNTPServerTable. |
| 1.3.6.1.4.1.17713.6.17.15 | TablesNTPServerTable | not-accessible | current | |
| 1.3.6.1.4.1.17713.6.17.15.1 | RowsNTPServerTableEntry | not-accessible | current | Table SNTPServerTable |
| 1.3.6.1.4.1.17713.6.17.15.1.1 | ColumnsNTPServerTableIndex | not-accessible | current | Index range for the SNTPServerTable. |
| 1.3.6.1.4.1.17713.6.17.15.1.2 | ColumnsNTPServerIPAddress | read-write | current | The IP address of a valid SNTP server |
| 1.3.6.1.4.1.17713.6.17.15.1.3 | ColumnsNTPServerPortNumber | read-write | current | The IP port number of the SNTP server. Defaults to port 123. |
| 1.3.6.1.4.1.17713.6.17.15.1.4 | ColumnsNTPServerStatus | read-only | current | Status message reflecting the result of communications with the SNTP server when last polled |
| 1.3.6.1.4.1.17713.6.17.15.1.5 | ColumnsNTPServerInternetAddressType | read-only | current | The type of Internet address specified by the associated sNTPServerInternetAddress. |
| 1.3.6.1.4.1.17713.6.17.15.1.6 | ColumnsNTPServerInternetAddress | read-write | current | The Internet address of a valid SNTP server |
| 1.3.6.1.4.1.17713.6.18 | Nodereset | |||
| 1.3.6.1.4.1.17713.6.18.1 | ScalarsystemReset | read-write | current | Setting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memory |
| 1.3.6.1.4.1.17713.6.19 | Nodeversions | |||
| 1.3.6.1.4.1.17713.6.19.1 | ScalarsoftwareVersion | read-only | current | Current software version |
| 1.3.6.1.4.1.17713.6.19.2 | ScalarhardwareVersion | read-only | current | Hardware platform version |
| 1.3.6.1.4.1.17713.6.19.3 | ScalarsecondarySoftwareVersion | read-only | current | Secondary software version, used when the primary software image is invalid or erased |
| 1.3.6.1.4.1.17713.6.19.4 | ScalarbootVersion | read-only | current | Boot code software version |
| 1.3.6.1.4.1.17713.6.20 | NodepubStats | |||
| 1.3.6.1.4.1.17713.6.20.1 | ScalarreceiveDataRate | read-only | current | Average data rate over the last one second interval (kbps) |
| 1.3.6.1.4.1.17713.6.20.2 | ScalartransmitDataRate | read-only | current | Average data rate over the last one second interval (kbps) |
| 1.3.6.1.4.1.17713.6.20.3 | ScalaraggregateDataRate | read-only | current | Average data rate over the last one second interval (kbps) |
| 1.3.6.1.4.1.17713.6.20.4 | ScalarwirelessLinkAvailability | read-only | current | Link availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision |
| 1.3.6.1.4.1.17713.6.20.5 | ScalarwirelessLinkStatus | read-only | current | Current status of the wireless link |
| 1.3.6.1.4.1.17713.6.20.6 | ScalarbyteErrorRatio | read-only | current | Reciprocal of the byte error ratio calculated since the last reset of the system counters |
| 1.3.6.1.4.1.17713.6.20.7 | ScalarreceiveModulationModeDetail | read-only | current | The reason for the current receive modulation mode |
| 1.3.6.1.4.1.17713.6.20.8 | ScalarethernetBridgingAvailability | read-only | current | Link availability bridging Ethernet traffic calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal pl… |
| 1.3.6.1.4.1.17713.6.22 | Nodeencryption | |||
| 1.3.6.1.4.1.17713.6.22.1 | ScalarencryptionAlgorithm | read-only | current | The Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm mu… |
| 1.3.6.1.4.1.17713.6.23 | NodetDDControl | |||
| 1.3.6.1.4.1.17713.6.23.1 | ScalartDDSynchronizationMode | read-only | current | TDD Synchronization Mode selection |
| 1.3.6.1.4.1.17713.6.24 | NodesyslogControl | |||
| 1.3.6.1.4.1.17713.6.24.1 | ScalarsyslogClient | read-only | current | Enable or disable the syslog client |
| 1.3.6.1.4.1.17713.6.24.2 | ScalarsyslogState | read-only | current | The syslog service has been enabled or disabled |
| 1.3.6.1.4.1.17713.6.25 | NodeaAAControl | |||
| 1.3.6.1.4.1.17713.6.25.1 | ScalaruserTableNumber | read-only | current | Number of entries in the userTable |
| 1.3.6.1.4.1.17713.6.25.2 | TableuserTable | not-accessible | current | The User Table Control group contains objects specifically for user account management. |
| 1.3.6.1.4.1.17713.6.25.2.1 | RowuserTableEntry | not-accessible | current | Table UserTable |
| 1.3.6.1.4.1.17713.6.25.2.1.1 | ColumnuserTableIndex | not-accessible | current | used to index values in the userTable. |
| 1.3.6.1.4.1.17713.6.25.2.1.2 | ColumnuserName | read-only | current | User name which must be entered, along with the appropriate password, in order to gain access to the system. |
| 1.3.6.1.4.1.17713.6.25.2.1.3 | ColumnuserRole | read-only | current | Role of the selected user. A Security Officer has access to and can modify all settings. A System Administrator has access to and can modify all non-security s… |
| 1.3.6.1.4.1.17713.6.25.2.1.4 | ColumnuserEnabled | read-only | current | Enable / Disable the selected user |
| 1.3.6.1.4.1.17713.6.25.2.1.5 | ColumnuserPassword | read-write | current | User password, which must be entered in order to gain access to the system. |
| 1.3.6.1.4.1.17713.6.96 | Nodesupplementary | |||
| 1.3.6.1.4.1.17713.6.96.1 | Scalarlongitude | read-write | current | The longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function. |
| 1.3.6.1.4.1.17713.6.96.2 | Scalarlatitude | read-write | current | The latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function. |
| 1.3.6.1.4.1.17713.6.96.3 | Scalaraltitude | read-write | current | The altitude of the unit, measured in metres. This object is set by the SNMP manager and has no internal function. |
| 1.3.6.1.4.1.17713.6.97 | ComplianceptpCompliance | current | The compliance statement for the Cambium PTP MIB | |
| 1.3.6.1.4.1.17713.6.98 | NodeptpGroups | |||
| 1.3.6.1.4.1.17713.6.98.3 | GroupdfsGroup | current | The dfs object group. | |
| 1.3.6.1.4.1.17713.6.98.4 | GroupbridgeGroup | current | The bridge object group. | |
| 1.3.6.1.4.1.17713.6.98.5 | GroupconfigurationGroup | current | The configuration object group. | |
| 1.3.6.1.4.1.17713.6.98.6 | GroupethernetGroup | current | The ethernet object group. | |
| 1.3.6.1.4.1.17713.6.98.7 | GrouptelecomGroup | current | The telecom object group. | |
| 1.3.6.1.4.1.17713.6.98.8 | GrouplicenceGroup | current | The licence object group. | |
| 1.3.6.1.4.1.17713.6.98.9 | GroupmanagementGroup | current | The management object group. | |
| 1.3.6.1.4.1.17713.6.98.10 | GroupphyControlGroup | current | The phyControl object group. | |
| 1.3.6.1.4.1.17713.6.98.12 | GroupphyStatusGroup | current | The phyStatus object group. | |
| 1.3.6.1.4.1.17713.6.98.13 | GroupalarmsGroup | current | The alarms object group. | |
| 1.3.6.1.4.1.17713.6.98.15 | GroupsmtpGroup | current | The smtp object group. | |
| 1.3.6.1.4.1.17713.6.98.16 | GroupsnmpControlGroup | current | The snmpControl object group. | |
| 1.3.6.1.4.1.17713.6.98.17 | GroupsntpGroup | current | The sntp object group. | |
| 1.3.6.1.4.1.17713.6.98.18 | GroupresetGroup | current | The reset object group. | |
| 1.3.6.1.4.1.17713.6.98.19 | GroupversionsGroup | current | The versions object group. | |
| 1.3.6.1.4.1.17713.6.98.20 | GrouppubStatsGroup | current | The pubStats object group. | |
| 1.3.6.1.4.1.17713.6.98.22 | GroupencryptionGroup | current | The encryption object group. | |
| 1.3.6.1.4.1.17713.6.98.23 | GrouptDDControlGroup | current | The tDDControl object group. | |
| 1.3.6.1.4.1.17713.6.98.24 | GroupsyslogControlGroup | current | The syslogControl object group. | |
| 1.3.6.1.4.1.17713.6.98.25 | GroupaAAControlGroup | current | The aAAControl object group. | |
| 1.3.6.1.4.1.17713.6.98.96 | GroupsupplementaryGroup | current | The supplementary object group. | |
| 1.3.6.1.4.1.17713.6.98.99 | GroupnotificationsGroup | current | The notifications group. | |
| 1.3.6.1.4.1.17713.6.99 | NodeptpTraps | |||
| 1.3.6.1.4.1.17713.6.99.0 | NodeptpTrapPrefix | |||
| 1.3.6.1.4.1.17713.6.99.0.1 | NotificationchannelChangeTrap | current | The PTP radio has changed wireless channel. This has been caused by either i) mandatory radar avoidance, a DFS impulsive interference event will also be detect… | |
| 1.3.6.1.4.1.17713.6.99.0.2 | NotificationdfsImpulsiveInterferenceTrap | current | DFS impulsive interference detected event | |
| 1.3.6.1.4.1.17713.6.99.0.3 | NotificationdataPortStatusTrap | current | Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert | |
| 1.3.6.1.4.1.17713.6.99.0.4 | NotificationtelecomsChannelAStatusTrap | current | Current status of telecoms channel A. NB: a change of state may generate an SNMP trap and/or SMTP email alert | |
| 1.3.6.1.4.1.17713.6.99.0.5 | NotificationtelecomsChannelBStatusTrap | current | Current status of telecoms channel B. NB: a change of state may generate an SNMP trap and/or SMTP email alert | |
| 1.3.6.1.4.1.17713.6.99.0.6 | NotificationchannelALoopbackTrap | current | The loopback status of telecoms channel A. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to … | |
| 1.3.6.1.4.1.17713.6.99.0.7 | NotificationchannelBLoopbackTrap | current | The loopback status of telecoms channel B. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to … | |
| 1.3.6.1.4.1.17713.6.99.0.8 | NotificationregionCodeTrap | current | The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted license key. NB: a change… | |
| 1.3.6.1.4.1.17713.6.99.0.9 | NotificationinstallStatusTrap | current | A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because un… | |
| 1.3.6.1.4.1.17713.6.99.0.10 | NotificationinstallArmStateTrap | current | Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert | |
| 1.3.6.1.4.1.17713.6.99.0.11 | NotificationunitOutOfCalibrationTrap | current | The unit is out of calibration | |
| 1.3.6.1.4.1.17713.6.99.0.14 | NotificationincompatibleRegionCodesTrap | current | The master and slave units have incompatible region codes. NB: Both units must have compatible license keys | |
| 1.3.6.1.4.1.17713.6.99.0.15 | NotificationnoWirelessChannelAvailableTrap | current | Spectrum Management was unable to locate a suitable wireless channel to operate on | |
| 1.3.6.1.4.1.17713.6.99.0.16 | NotificationwirelessLinkDisabledWarningTrap | current | The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic | |
| 1.3.6.1.4.1.17713.6.99.0.17 | NotificationdataPortDisabledWarningTrap | current | The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic | |
| 1.3.6.1.4.1.17713.6.99.0.18 | NotificationdataPortFiberStatusTrap | current | If the fiber link is not OK, there are three possible causes: Either the fiber link has been installed but disabled (because the license key does not include f… | |
| 1.3.6.1.4.1.17713.6.99.0.19 | NotificationdataPortConfigurationMismatchTrap | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch | |
| 1.3.6.1.4.1.17713.6.99.0.20 | NotificationincompatibleMasterAndSlaveTrap | current | A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusua… | |
| 1.3.6.1.4.1.17713.6.99.0.21 | NotificationsNTPSyncTrap | current | If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP | |
| 1.3.6.1.4.1.17713.6.99.0.22 | NotificationtDDSynchronizationAlarmTrap | current | Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this lin… | |
| 1.3.6.1.4.1.17713.6.99.0.23 | NotificationmanagementPortStatusTrap | current | Current status of the out-of-band management link. NB: a change of state may generate an SNMP trap and/or SMTP email alert | |
| 1.3.6.1.4.1.17713.6.99.0.24 | NotificationmanagementPortDisabledWarningTrap | current | The SNMP ifAdminStatus of the out-of-band management interface has disabled Ethernet traffic | |
| 1.3.6.1.4.1.17713.6.99.0.25 | NotificationlinkModeOptimizationMismatchTrap | current | The remote node of this link has been configured with a different link mode optimization | |
| 1.3.6.1.4.1.17713.6.99.0.28 | NotificationmanagementPortConfigurationMismatchTrap | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. Th… | |
| 1.3.6.1.4.1.17713.6.99.0.30 | NotificationsyslogStateTrap | current | The syslog service has been enabled or disabled | |
| 1.3.6.1.4.1.17713.6.99.0.31 | NotificationsyslogLocalNearlyFullTrap | current | The syslog local log is nearly full (90%) | |
| 1.3.6.1.4.1.17713.6.99.0.32 | NotificationsyslogLocalWrappedTrap | current | The syslog local log has wrapped | |
| 1.3.6.1.4.1.17713.6.99.0.33 | NotificationsyslogClientTrap | current | Enable or disable the syslog client | |
| 1.3.6.1.4.1.17713.6.99.0.34 | NotificationsecureModeAlarmTrap | current | The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, … | |
| 1.3.6.1.4.1.17713.6.99.0.35 | NotificationethernetBridgingStatusAlarmTrap | current | Ethernet traffic bridging is disabled because the wireless link is not operating at the configured Lowest Ethernet Modulation Mode |