CAMBIUM-PTP670-MIB
569 objects
MIB for non-line-of-sight (NLOS) wireless ethernet bridge.
Imported Objects
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter64 enterprises Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.17713 | Identitycambium | MIB for non-line-of-sight (NLOS) wireless ethernet bridge. | ||
| 1.3.6.1.4.1.17713.1 | Nodeptp | |||
| 1.3.6.1.4.1.17713.2 | Nodeptmp | |||
| 1.3.6.1.4.1.17713.11 | Nodeptp670 | |||
| 1.3.6.1.4.1.17713.11.3 | Nodedfs | |||
| 1.3.6.1.4.1.17713.11.3.1 | ScalardfsTableNumber | read-only | current | Number of entries in the dfsTable |
| 1.3.6.1.4.1.17713.11.3.2 | TabledfsTable | not-accessible | current | A table storing a snapshot of various DFS measurements for each channel |
| 1.3.6.1.4.1.17713.11.3.2.1 | RowdfsTableEntry | not-accessible | current | Table DfsTable |
| 1.3.6.1.4.1.17713.11.3.2.1.1 | ColumndfsTableIndex | not-accessible | current | used to index values in the dfsTable. |
| 1.3.6.1.4.1.17713.11.3.2.1.2 | ColumndfsMeans | read-only | current | Snapshot of DFS means |
| 1.3.6.1.4.1.17713.11.3.2.1.3 | ColumndfsNineNinePointNinePercentiles | read-only | current | Snapshot of DFS 99.9 percentiles |
| 1.3.6.1.4.1.17713.11.3.2.1.4 | ColumndfsPeaks | read-only | current | Snapshot of DFS peaks |
| 1.3.6.1.4.1.17713.11.3.3 | ScalarextendedSpectrumScanning | read-only | current | Enables Extended Spectrum Scanning |
| 1.3.6.1.4.1.17713.11.4 | Nodebridge | |||
| 1.3.6.1.4.1.17713.11.4.1 | ScalarlocalPacketFiltering | read-write | current | When Local Packet Filtering is Enabled, the unit keeps track of the port (Main, SFP, Aux or Wireless) on which a packet with a given MAC source address destine… |
| 1.3.6.1.4.1.17713.11.4.2 | ScalarpacketsToInternalStack | read-only | current | Total number of good packets the bridge has transmitted to the internal TCP/IP stack. |
| 1.3.6.1.4.1.17713.11.4.3 | ScalarpacketsFromInternalStack | read-only | current | Total number of good packets the bridge has received from the internal TCP/IP stack. |
| 1.3.6.1.4.1.17713.11.5 | Nodeconfiguration | |||
| 1.3.6.1.4.1.17713.11.5.1 | ScalariPv4Address | read-write | current | Internet protocol (IPv4) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. |
| 1.3.6.1.4.1.17713.11.5.2 | ScalarsubnetMask | read-write | current | A subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnettin… |
| 1.3.6.1.4.1.17713.11.5.3 | ScalargatewayIPAddress | read-write | current | The IPv4 address of a device on the current network that acts as an IPv4 network gateway. A gateway acts as an entrance / exit to packets from / to other netwo… |
| 1.3.6.1.4.1.17713.11.5.4 | ScalartargetMACAddress | read-only | current | MAC address of the unit forming the other end of the link |
| 1.3.6.1.4.1.17713.11.5.5 | ScalarmasterSlaveMode | read-write | current | The wireless link operates using a master and slave relationship |
| 1.3.6.1.4.1.17713.11.5.6 | ScalarmaximumTransmitPower | read-only | current | Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link. This may be reduced during installation |
| 1.3.6.1.4.1.17713.11.5.7 | ScalarantennaGain | read-write | current | Antenna Gain. Expressed in 10ths of dBi. |
| 1.3.6.1.4.1.17713.11.5.8 | ScalarcableLoss | read-write | current | Loss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna. |
| 1.3.6.1.4.1.17713.11.5.9 | ScalareIRP | read-only | current | Effective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBm |
| 1.3.6.1.4.1.17713.11.5.11 | ScalarchannelBandwidth | read-only | current | This control sets the bandwidth of the transmit and receive radio channels |
| 1.3.6.1.4.1.17713.11.5.14 | ScalarlinkName | read-write | current | Name of the link allocated by the System Administrator. Used to establish a connection with the correct wireless unit at the other end of the link. NOTE: The l… |
| 1.3.6.1.4.1.17713.11.5.15 | ScalarsiteName | read-write | current | This field contains a user-provided description of the site name together with any additional notes |
| 1.3.6.1.4.1.17713.11.5.16 | ScalaraccessMethod | read-only | current | ODUs must be configured in pairs before a link can be established. The Access Method attribute determines how the paired ODUs will recognise each other. For th… |
| 1.3.6.1.4.1.17713.11.5.17 | ScalargroupID | read-write | current | When Access Method is set to Group Access, the Group ID identifies all the units belonging to the same group |
| 1.3.6.1.4.1.17713.11.5.18 | ScalariPv6Address | read-write | current | Internet protocol (IPv6) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. |
| 1.3.6.1.4.1.17713.11.5.20 | ScalariPVersion | read-write | current | IP protocol selection. Choice of IPv4, IPv6 or Dual. |
| 1.3.6.1.4.1.17713.11.5.21 | ScalariPv6AutoConfiguredLinkLocalAddress | read-only | current | The auto configured link local IPv6 address |
| 1.3.6.1.4.1.17713.11.5.22 | ScalariPv6PrefixLength | read-write | current | IPv6 prefix length |
| 1.3.6.1.4.1.17713.11.5.23 | ScalariPv6GatewayAddress | read-write | current | The IPv6 address of a device on the current network that is currently acting as an IPv6 network gateway. A gateway acts as an entrance / exit to packets from /… |
| 1.3.6.1.4.1.17713.11.5.24 | ScalarremoteInternetAddressTypeLinked | read-only | current | The type of Internet address specified by the associated remoteInternetAddressType. |
| 1.3.6.1.4.1.17713.11.5.25 | ScalarremoteInternetAddressLinked | read-only | current | INET address used to identify the peer wireless unit |
| 1.3.6.1.4.1.17713.11.5.26 | ScalarsubbandLowestFrequency | read-only | current | Lowest center frequency of the subset of channels. |
| 1.3.6.1.4.1.17713.11.5.27 | ScalarsubbandHighestFrequency | read-only | current | Highest center frequency of the subset of channels. |
| 1.3.6.1.4.1.17713.11.5.28 | ScalarenableTransmission | read-write | current | Control for enabling/disabling the radio transmitter of the Master. Note: Use Web Properties to control this feature. |
| 1.3.6.1.4.1.17713.11.5.29 | ScalarantennaSelection | read-only | current | Antenna Selection. Choice of Integrated or Connectorized |
| 1.3.6.1.4.1.17713.11.5.30 | ScalartransmitterChannels | read-write | current | To select transmitter channel(s) (H,V) |
| 1.3.6.1.4.1.17713.11.5.31 | ScalarwirelessTopology | read-only | current | This attribute determines whether the device operates as part of a PTP or an HCMP network topology. |
| 1.3.6.1.4.1.17713.11.5.32 | ScalarconfigurationInstancedTableNumber | read-only | current | Number of entries in the ConfigurationInstancedTable. |
| 1.3.6.1.4.1.17713.11.5.33 | TableconfigurationInstancedTable | not-accessible | current | Instanced Public stats table. |
| 1.3.6.1.4.1.17713.11.5.33.1 | RowconfigurationInstancedTableEntry | not-accessible | current | Table ConfigurationInstancedTable |
| 1.3.6.1.4.1.17713.11.5.33.1.1 | ColumnconfigurationInstancedTableIndex | not-accessible | current | Used to index the ConfigurationInstancedTable. |
| 1.3.6.1.4.1.17713.11.5.33.1.2 | ColumnremoteInternetAddressType | read-only | current | The type of Internet address specified by the associated remoteInternetAddressType. |
| 1.3.6.1.4.1.17713.11.5.33.1.3 | ColumnremoteInternetAddress | read-only | current | INET address used to identify the peer wireless unit |
| 1.3.6.1.4.1.17713.11.5.33.1.4 | ColumnremoteUnitName | read-only | current | This field contains user-provided name of the peer received over the wireless link |
| 1.3.6.1.4.1.17713.11.5.34 | ScalarunitName | read-write | current | This field contains user-provided name for this unit |
| 1.3.6.1.4.1.17713.11.5.35 | ScalarauthorizationMethod | read-only | current | Authorization Method to be used - Whitelist or Blacklist |
| 1.3.6.1.4.1.17713.11.5.36 | ScalarremoteUnitNameLinked | read-only | current | This field contains user-provided name of the peer received over the wireless link |
| 1.3.6.1.4.1.17713.11.6 | Nodeethernet | |||
| 1.3.6.1.4.1.17713.11.6.1 | ScalarmainPSUPortAutoNegotiation | read-only | current | This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiat… |
| 1.3.6.1.4.1.17713.11.6.2 | ScalarmainPSUPortAutoNegAdvertisement | read-only | current | This sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system rebo… |
| 1.3.6.1.4.1.17713.11.6.3 | ScalarmainPSUPortAutoMdix | read-only | current | This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot |
| 1.3.6.1.4.1.17713.11.6.4 | ScalarmainPSUPortStatus | read-only | current | Current status of the Main PSU Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.11.6.5 | ScalarmainPSUPortSpeedAndDuplex | read-only | current | The current speed and duplex of the Main PSU Ethernet link |
| 1.3.6.1.4.1.17713.11.6.6 | ScalardataPortWirelessDownAlert | read-write | current | When enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect tha… |
| 1.3.6.1.4.1.17713.11.6.7 | ScalaruseVLANForManagementInterfaces | read-write | current | This controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system reboot |
| 1.3.6.1.4.1.17713.11.6.8 | ScalarvLANManagementPriority | read-write | current | This VLAN Priority (0-7) will be included in packets generated by the management interfaces |
| 1.3.6.1.4.1.17713.11.6.11 | ScalarvLANManagementVID | read-write | current | This VLAN VID (0-4094) will be included in packets generated by the management interfaces. Note the new setting will only take effect after a system reboot |
| 1.3.6.1.4.1.17713.11.6.12 | ScalarauxPortStatus | read-only | current | Current status of the Aux Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.11.6.13 | ScalarauxPortSpeedAndDuplex | read-only | current | The current speed and duplex of the Aux Ethernet link |
| 1.3.6.1.4.1.17713.11.6.14 | ScalarethernetPriorityTableNumber | read-only | current | Number of entries in the vLANPriorityTable. |
| 1.3.6.1.4.1.17713.11.6.15 | TableethernetPriorityTable | not-accessible | current | A priority queue mapping table. This is a list of packet queues indexed by Ethernet priority. |
| 1.3.6.1.4.1.17713.11.6.15.1 | RowethernetPriorityTableEntry | not-accessible | current | Table EthernetPriorityTable |
| 1.3.6.1.4.1.17713.11.6.15.1.1 | ColumnethernetPriorityTableIndex | not-accessible | current | Ethernet priority flag, used to index values in the ethernetPriorityTable |
| 1.3.6.1.4.1.17713.11.6.15.1.2 | ColumnethernetPriorityQueueMapping | read-write | current | Configures the classification of this Ethernet priority (also known as IEEE 802.1p value) to an egress queue at the wireless port |
| 1.3.6.1.4.1.17713.11.6.16 | Scalarl2CPPriorityTableNumber | read-only | current | Number of entries in the l2CPPriorityTable. |
| 1.3.6.1.4.1.17713.11.6.17 | Tablel2CPPriorityTable | not-accessible | current | A priority queue mapping table. This is a list of packet queues indexed by L2CP priority. |
| 1.3.6.1.4.1.17713.11.6.17.1 | Rowl2CPPriorityTableEntry | not-accessible | current | Table L2CPPriorityTable |
| 1.3.6.1.4.1.17713.11.6.17.1.1 | Columnl2CPPriorityTableIndex | not-accessible | current | L2CP priority flag, used to index values in the l2CPPriorityTable |
| 1.3.6.1.4.1.17713.11.6.17.1.2 | Columnl2CPPriorityQueueMapping | read-write | current | Configures the classification of this layer two control protocol (L2CP) to an egress queue at the wireless port |
| 1.3.6.1.4.1.17713.11.6.18 | ScalariPDSCPPriorityTableNumber | read-only | current | Number of entries in the iPDSCPPriorityTable. |
| 1.3.6.1.4.1.17713.11.6.19 | TableiPDSCPPriorityTable | not-accessible | current | A priority queue mapping table. This is a list of packet queues indexed by L3 IP DSCP priority. |
| 1.3.6.1.4.1.17713.11.6.19.1 | RowiPDSCPPriorityTableEntry | not-accessible | current | Table IPDSCPPriorityTable |
| 1.3.6.1.4.1.17713.11.6.19.1.1 | ColumniPDSCPPriorityTableIndex | not-accessible | current | IP DSCP priority flag, used to index values in the iPDSCPPriorityTable |
| 1.3.6.1.4.1.17713.11.6.19.1.2 | ColumniPDSCPPriorityQueueMapping | read-write | current | Configures the classification of this IP differentiated services code point (DSCP) value to an egress queue at the wireless port |
| 1.3.6.1.4.1.17713.11.6.20 | ScalarmPLSTCPriorityTableNumber | read-only | current | Number of entries in the mPLSTCPriorityTable. |
| 1.3.6.1.4.1.17713.11.6.21 | TablemPLSTCPriorityTable | not-accessible | current | A priority queue mapping table. This is a list of priority queues indexed by MPLS TC priority. |
| 1.3.6.1.4.1.17713.11.6.21.1 | RowmPLSTCPriorityTableEntry | not-accessible | current | Table MPLSTCPriorityTable |
| 1.3.6.1.4.1.17713.11.6.21.1.1 | ColumnmPLSTCPriorityTableIndex | not-accessible | current | MPLS TC priority flag, used to index values in the mPLSTCPriorityTable |
| 1.3.6.1.4.1.17713.11.6.21.1.2 | ColumnmPLSTCPriorityQueueMapping | read-write | current | Configures the classification of this MPLS traffic class (the field formerly known as EXP) to an egress queue at the wireless port |
| 1.3.6.1.4.1.17713.11.6.23 | ScalarmanagementPortWirelessDownAlert | read-write | current | When enabled, this causes the management link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect t… |
| 1.3.6.1.4.1.17713.11.6.24 | ScalarqOSPriorityScheme | read-write | current | Selects classification based on fields in the Ethernet header (Layer 2) or in the Network header (Layer 3). The unit recognises two network layer protocols: IP… |
| 1.3.6.1.4.1.17713.11.6.25 | ScalarunknownNetworkPriorityQueueMapping | read-write | current | Configures the classification of unknown network protocols to an egress queue at the wireless port. Unknown means something other than IP and MPLS |
| 1.3.6.1.4.1.17713.11.6.26 | ScalardSCPManagementPriority | read-only | current | This Differentiated Services Code Point value will be inserted in the IP Header of all IP Datagrams transmitted by the management interfaces |
| 1.3.6.1.4.1.17713.11.6.27 | ScalardataBridgingStatusLinked | read-only | current | Current status of Ethernet Data traffic bridging over the wireless link |
| 1.3.6.1.4.1.17713.11.6.28 | ScalarmainPSUPortAllocation | read-only | current | Indicates the service or services supported by the Main PSU Ethernet port |
| 1.3.6.1.4.1.17713.11.6.29 | ScalarauxPortAllocation | read-only | current | Indicates the service or services supported by the Aux Ethernet port |
| 1.3.6.1.4.1.17713.11.6.30 | ScalarsFPPortAllocation | read-only | current | Indicates the service or services supported by the SFP Ethernet port |
| 1.3.6.1.4.1.17713.11.6.31 | ScalardataPortPauseFrames | read-only | current | Controls whether the bridge tunnels or discards Layer 2 PAUSE frames arriving at the Data Port. Such frames are identified by the destination MAC Address being… |
| 1.3.6.1.4.1.17713.11.6.32 | ScalarsFPPortAutoNegotiation | read-only | current | This controls whether the local SFP Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto nego… |
| 1.3.6.1.4.1.17713.11.6.33 | ScalarsFPPortAutoNegAdvertisement | read-only | current | This sets the different SFP Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system … |
| 1.3.6.1.4.1.17713.11.6.34 | ScalarsFPPortAutoMdix | read-only | current | This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot |
| 1.3.6.1.4.1.17713.11.6.35 | ScalarsFPPortStatus | read-only | current | Current status of the SFP Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.11.6.36 | ScalarsFPPortSpeedAndDuplex | read-only | current | The current speed and duplex of the SFP Ethernet link |
| 1.3.6.1.4.1.17713.11.6.37 | ScalarauxPortPowerOverEthernetOutput | read-only | current | The state of the Power Over Ethernet (PoE) output of the Aux port. Enabling PoE output may lead to system instability; please refer to the User Guide before en… |
| 1.3.6.1.4.1.17713.11.6.38 | ScalarauxPortPowerOverEthernetOutputStatus | read-only | current | Current status of the Power Over Ethernet (PoE) output of the Aux port |
| 1.3.6.1.4.1.17713.11.6.39 | ScalarsyncETracking | read-write | current | Controls whether Synchronous Ethernet (SyncE) network synchronization is enabled. |
| 1.3.6.1.4.1.17713.11.6.40 | ScalarsyncEEquipmentClock | read-write | current | EEC-Option 1 applies to synchronous Ethernet equipments that are designed to interwork with networks optimized for the 2048-kbit/s hierarchy. Corresponds to IT… |
| 1.3.6.1.4.1.17713.11.6.41 | ScalarmainPSUPortQLRxOverwrite | read-write | current | Override for the Synchronous Ethernet (SyncE) received Quality Level (QL) on the main PSU port. |
| 1.3.6.1.4.1.17713.11.6.42 | ScalarmainPSUPortSSMTx | read-write | current | Controls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the Main PSU port |
| 1.3.6.1.4.1.17713.11.6.43 | ScalarsFPPortSSMTx | read-write | current | Controls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the SFP port |
| 1.3.6.1.4.1.17713.11.6.44 | ScalarauxPortSSMTx | read-write | current | Controls whether the Synchronous Ethernet (SyncE) Quality Level (QL) is transmitted on the Aux port |
| 1.3.6.1.4.1.17713.11.6.45 | ScalarsyncETrackingState | read-only | current | The current state of Synchronous Ethernet (SyncE) network synchronization. |
| 1.3.6.1.4.1.17713.11.6.46 | ScalarmainPSUPortQLRx | read-only | current | The Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the main PSU port. |
| 1.3.6.1.4.1.17713.11.6.47 | ScalarauxPortQLRx | read-only | current | The Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the auxiliary port. |
| 1.3.6.1.4.1.17713.11.6.48 | ScalarsFPPortQLRx | read-only | current | The Synchronous Ethernet (SyncE) Quality Level (QL) currently being received on the SFP port. |
| 1.3.6.1.4.1.17713.11.6.49 | ScalarmainPSUPortQLTx | read-only | current | The Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the main PSU port. |
| 1.3.6.1.4.1.17713.11.6.50 | ScalarauxPortQLTx | read-only | current | The Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the auxiliary port. |
| 1.3.6.1.4.1.17713.11.6.51 | ScalarsFPPortQLTx | read-only | current | The Synchronous Ethernet (SyncE) transmit Quality Level (QL) of the SFP port. |
| 1.3.6.1.4.1.17713.11.6.52 | ScalarmainPSUPortSyncEMasterSlaveStatus | read-only | current | The main PSU port Synchronous Ethernet (SyncE) Master/Slave status |
| 1.3.6.1.4.1.17713.11.6.53 | ScalarauxPortSyncEMasterSlaveStatus | read-only | current | The auxiliary port Synchronous Ethernet (SyncE) Master/Slave status |
| 1.3.6.1.4.1.17713.11.6.54 | ScalarsFPPortSyncEMasterSlaveStatus | read-only | current | The SFP port Synchronous Ethernet (SyncE) Master/Slave status |
| 1.3.6.1.4.1.17713.11.6.55 | ScalarmainPSUPortGigabitMasterSlaveStatus | read-only | current | The main PSU port Gigabit Ethernet Master/Slave status |
| 1.3.6.1.4.1.17713.11.6.56 | ScalarauxPortGigabitMasterSlaveStatus | read-only | current | The auxiliary port Gigabit Ethernet Master/Slave status |
| 1.3.6.1.4.1.17713.11.6.57 | ScalarsFPPortGigabitMasterSlaveStatus | read-only | current | The SFP port Gigabit Ethernet Master/Slave status |
| 1.3.6.1.4.1.17713.11.6.58 | ScalartransparentClock | read-write | current | This control enables the Precision Time Protocol (IEEE-1588) Transparent Clock. Once enabled the unit will modify the correction field in PTP event messages to… |
| 1.3.6.1.4.1.17713.11.6.59 | ScalartransparentClockVLAN | read-write | current | If All is selected then all PTP frames will have their correction fields modified with the residence time. If an S-TAG or C-TAG is selected, only frames with t… |
| 1.3.6.1.4.1.17713.11.6.60 | ScalartransparentClockVID | read-write | current | The VLAN ID which frames must match if they are to be corrected. Only valid when an S-TAG or C-TAG has been selected. |
| 1.3.6.1.4.1.17713.11.6.61 | ScalarmainPSUPortAcceptedQLRx | read-only | current | The Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the main PSU port. |
| 1.3.6.1.4.1.17713.11.6.62 | ScalarauxPortAcceptedQLRx | read-only | current | The Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the auxiliary port. |
| 1.3.6.1.4.1.17713.11.6.63 | ScalarsFPPortAcceptedQLRx | read-only | current | The Synchronous Ethernet (SyncE) Quality Level (QL) currently accepted (validated) on the SFP port. |
| 1.3.6.1.4.1.17713.11.6.64 | ScalarmainPSUPortSyncERxStatus | read-only | current | The Synchronous Ethernet (SyncE) Receive Status of the main PSU port |
| 1.3.6.1.4.1.17713.11.6.65 | ScalarauxPortSyncERxStatus | read-only | current | The Synchronous Ethernet (SyncE) Receive Status of the auxiliary port |
| 1.3.6.1.4.1.17713.11.6.66 | ScalarsFPPortSyncERxStatus | read-only | current | The Synchronous Ethernet (SyncE) Receive Status of the SFP port |
| 1.3.6.1.4.1.17713.11.6.67 | ScalarnIDULanPortStatus | read-only | current | Current status of the NIDU LAN Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.11.6.68 | ScalarnIDULanPortSpeedAndDuplex | read-only | current | The current speed and duplex of the Ethernet link to the NIDU LAN Port |
| 1.3.6.1.4.1.17713.11.6.69 | ScalaroOBPriorityQueueMapping | read-write | current | Configures the classification of traffic to an egress queue at the wireless port |
| 1.3.6.1.4.1.17713.11.6.70 | ScalarnIDULanPortAutoNegotiation | read-only | current | This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiat… |
| 1.3.6.1.4.1.17713.11.6.71 | ScalarnIDULanPortAutoNegAdvertisement | read-only | current | This sets the different Ethernet configurations that will be advertised during auto negotiation. Note the new setting will only take effect after a system rebo… |
| 1.3.6.1.4.1.17713.11.6.72 | ScalarnIDULanPortAutoMdix | read-only | current | This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot |
| 1.3.6.1.4.1.17713.11.6.73 | ScalarnIDULanPortGigabitMasterSlaveStatus | read-only | current | The NIDU LAN port Gigabit Ethernet Master/Slave status |
| 1.3.6.1.4.1.17713.11.6.74 | ScalartxMABFrames | read-only | current | Number of MAB frames transmitted |
| 1.3.6.1.4.1.17713.11.6.75 | ScalarmanagementNetworkAccessEnabled | read-write | current | When enabled the local Out-of-Band interface can be used to access the remote management network. If not enabled the local management agent can still be access… |
| 1.3.6.1.4.1.17713.11.6.81 | ScalartransparentClockPort | read-write | current | IEEE 1588 Transparent Clock source |
| 1.3.6.1.4.1.17713.11.6.82 | ScalarsyncESlavePort | read-write | current | Select a Sync E Slave Port |
| 1.3.6.1.4.1.17713.11.6.83 | ScalarsFPPortQLRxOverwrite | read-write | current | Override for the Synchronous Ethernet (SyncE) received Quality Level (QL) on the SFP Port. |
| 1.3.6.1.4.1.17713.11.6.84 | ScalarethernetInstancedTableNumber | read-only | current | Number of entries in the ethernetInstancedTable. |
| 1.3.6.1.4.1.17713.11.6.85 | TableethernetInstancedTable | not-accessible | current | Instanced table showing the ethernet status |
| 1.3.6.1.4.1.17713.11.6.85.1 | RowethernetInstancedTableEntry | not-accessible | current | Table EthernetInstancedTable |
| 1.3.6.1.4.1.17713.11.6.85.1.1 | ColumnethernetInstancedTableIndex | not-accessible | current | Used to index the ethernetInstancedTable. |
| 1.3.6.1.4.1.17713.11.6.85.1.2 | ColumndataBridgingStatus | read-only | current | Current status of Ethernet Data traffic bridging over the wireless link |
| 1.3.6.1.4.1.17713.11.6.86 | ScalarethernetStatisticsTableNumber | read-only | current | Number of entries in the ethernetStatisticsTable. |
| 1.3.6.1.4.1.17713.11.6.87 | TableethernetStatisticsTable | not-accessible | current | Instanced table showing the ethernet statistics |
| 1.3.6.1.4.1.17713.11.6.87.1 | RowethernetStatisticsTableEntry | not-accessible | current | Table EthernetStatisticsTable |
| 1.3.6.1.4.1.17713.11.6.87.1.1 | ColumnethernetStatisticsTableIndex | not-accessible | current | Used to index the ethernetStatisticsTable. |
| 1.3.6.1.4.1.17713.11.6.87.1.2 | ColumnethernetStatisticsDataSource | read-only | current | This object identifies the ethernet interface that this ethernetStatistics entry is configured to report. In order to identify a particular interface, this obj… |
| 1.3.6.1.4.1.17713.11.6.87.1.3 | ColumnethernetStatisticsRxOctets | read-only | current | Total number of octets (excluding framing bits but including FCS octets) received from the LAN in good packets |
| 1.3.6.1.4.1.17713.11.6.87.1.4 | ColumnethernetStatisticsRxFrames | read-only | current | Total number of packets (including bad packets, broadcast packets, and multicast packets) received |
| 1.3.6.1.4.1.17713.11.6.87.1.5 | ColumnethernetStatisticsRxBroadcasts | read-only | current | Number of good and bad broadcast packets received from the LAN. Note that this does not include multicast packets. |
| 1.3.6.1.4.1.17713.11.6.87.1.6 | ColumnethernetStatisticsRxFramesWithError | read-only | current | Number of frames received with errors. The errors can be a frame check sequence (CRC) error, an alignment error or an incorrect frame length |
| 1.3.6.1.4.1.17713.11.6.87.1.7 | ColumnethernetStatisticsRxFramesUndersize | read-only | current | Number of short frames (<64 Bytes) received from the LAN with or without a valid CRC |
| 1.3.6.1.4.1.17713.11.6.87.1.8 | ColumnethernetStatisticsRxFramesOversize | read-only | current | Number of oversize frames received from the LAN with or without a valid CRC |
| 1.3.6.1.4.1.17713.11.6.87.1.9 | ColumnethernetStatisticsTxOctets | read-only | current | Total number of octets transmitted to the LAN |
| 1.3.6.1.4.1.17713.11.6.87.1.10 | ColumnethernetStatisticsTxFrames | read-only | current | Total number of frames transmitted to the LAN |
| 1.3.6.1.4.1.17713.11.6.87.1.11 | ColumnethernetStatisticsTxBroadcasts | read-only | current | Number of broadcast frames transmitted to the LAN. Note that this does not include multicast packets. |
| 1.3.6.1.4.1.17713.11.7 | NodetDM | |||
| 1.3.6.1.4.1.17713.11.7.1 | ScalartDMInterfaceControl | read-only | current | The line interface type. If this is set to 'None' then the TDM interfaces are disabled, and the TDM settings will be ignored. |
| 1.3.6.1.4.1.17713.11.7.2 | ScalartDMInterfaceStatus | read-only | current | @Current status of the connection to the TDM Box. A state of 'Up' on a green background indicates that the TDM Box is connected OK. When connecting a TDM Box o… |
| 1.3.6.1.4.1.17713.11.7.3 | ScalartDMEnabledChannels | read-only | current | The number of TDM channels enabled in the system |
| 1.3.6.1.4.1.17713.11.7.4 | ScalartdmTableNumber | read-only | current | Number of entries in the TdmTable |
| 1.3.6.1.4.1.17713.11.7.5 | TabletdmTable | not-accessible | current | A table storing a configuration and status for each TDM channel |
| 1.3.6.1.4.1.17713.11.7.5.1 | RowtdmTableEntry | not-accessible | current | Table TdmTable |
| 1.3.6.1.4.1.17713.11.7.5.1.1 | ColumntdmTableIndex | not-accessible | current | TDM Channel flag, used to index channels in the TdmTable |
| 1.3.6.1.4.1.17713.11.7.5.1.2 | ColumntDMChannelStatus | read-only | current | Current status of the TDM channels. A value of 0 indicates that a TDM channel is established |
| 1.3.6.1.4.1.17713.11.7.5.1.3 | ColumntDMChannelLineCode | read-only | current | The line code setting of the TDM interfaces. This must match the setting of the device connected to an interface |
| 1.3.6.1.4.1.17713.11.7.5.1.4 | ColumntDMChannelCableLength | read-only | current | The lengths of the cables connected to the TDM interfaces, measured in feet |
| 1.3.6.1.4.1.17713.11.7.5.1.5 | ColumntDMChannelLoopback | read-only | current | The loopback status of TDM channels. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit… |
| 1.3.6.1.4.1.17713.11.7.6 | ScalartDMConfigurationMismatch | read-only | current | Current status of the configuration of the TDM Box. A state of 'Ok' on a green background indicates that the TDM Box configuration is matched OK with the remot… |
| 1.3.6.1.4.1.17713.11.7.7 | ScalarlowestTDMModulationMode | read-only | current | The lowest modulation mode at which tdm data will be sent. The effective lowest modulation mode is displayed in the TDM Configuration page |
| 1.3.6.1.4.1.17713.11.8 | Nodelicense | |||
| 1.3.6.1.4.1.17713.11.8.1 | ScalarregulatoryBand | read-only | current | The Regulatory Band prohibits the wireless unit from operating outside the regulated limits. An invalid Regulatory Band may be caused by a missing or incorrect… |
| 1.3.6.1.4.1.17713.11.8.2 | ScalarproductVariant | read-only | current | The product variant |
| 1.3.6.1.4.1.17713.11.8.3 | ScalarproductName | read-only | current | Name of the product variant |
| 1.3.6.1.4.1.17713.11.8.5 | ScalarfrequencyVariant | read-only | current | The hardware frequency variant |
| 1.3.6.1.4.1.17713.11.8.9 | ScalarsNMPv3Enable | read-only | current | SNMPv3 availability control |
| 1.3.6.1.4.1.17713.11.8.12 | ScalarlicenseVersion | read-only | current | The license key version. |
| 1.3.6.1.4.1.17713.11.8.13 | ScalarlicenseUnitSerialNumber | read-only | current | The unit serial number. |
| 1.3.6.1.4.1.17713.11.8.15 | ScalarlicenseIssueNumber | read-only | current | The license key issue number for this unit. |
| 1.3.6.1.4.1.17713.11.8.16 | ScalarlicenseCountry | read-only | current | The country in which this unit is licensed to operate. |
| 1.3.6.1.4.1.17713.11.8.17 | ScalarlicenseNumberOfRegulatoryBands | read-only | current | The number of regulatory bands for which the unit is licensed to operate. |
| 1.3.6.1.4.1.17713.11.8.18 | TablelicenseRegulatoryBandsTable | not-accessible | current | |
| 1.3.6.1.4.1.17713.11.8.18.1 | RowlicenseRegulatoryBandsTableEntry | not-accessible | current | Table LicenseRegulatoryBandsTable |
| 1.3.6.1.4.1.17713.11.8.18.1.1 | ColumnlicenseRegulatoryBandsTableIndex | not-accessible | current | License regulatory bands, used to index the LicenseRegulatoryBandsTable. |
| 1.3.6.1.4.1.17713.11.8.18.1.2 | ColumnlicenseRegulatoryBandsList | read-only | current | The list of regulatory bands for which the unit is licensed to operate. A regulatory band prohibits the wireless unit from operating outside the regulated limi… |
| 1.3.6.1.4.1.17713.11.8.20 | ScalarlicenseBandwidthCap | read-only | current | The wireless link bandwidth cap in MHz. Zero indicates no bandwidth cap. |
| 1.3.6.1.4.1.17713.11.8.21 | ScalarlicenseEncryption | read-only | current | The license key encryption algorithms available. |
| 1.3.6.1.4.1.17713.11.8.22 | ScalarlicenseSecurityLevel | read-only | current | The license key security level. |
| 1.3.6.1.4.1.17713.11.8.23 | ScalarlicenseGroupAccess | read-only | current | The license key group access setting. Note that for HCMP topology, license group access must be enabled. |
| 1.3.6.1.4.1.17713.11.8.24 | ScalarlicenseOOBManagementSupport | read-only | current | The license key Out-Of-Band (OOB) support setting. |
| 1.3.6.1.4.1.17713.11.8.25 | ScalarlicenseSFPPortSupport | read-only | current | The license key Ethernet SFP Port support setting. |
| 1.3.6.1.4.1.17713.11.8.26 | ScalarlicenseAuxiliaryPortSupport | read-only | current | The license key Ethernet Auxiliary Port support setting. |
| 1.3.6.1.4.1.17713.11.8.27 | ScalarlicenseCapacity | read-only | current | The license key capacity. Note that for HCMP topology, license capacity must be full. |
| 1.3.6.1.4.1.17713.11.8.28 | ScalarlicenseMaxNumberOfTDMChannels | read-only | current | The license key maximum TDM channels setting. Zero indicates TDM not available. |
| 1.3.6.1.4.1.17713.11.8.29 | ScalarlicenseIEEE1588Support | read-only | current | The license key IEEE-1588 support setting. |
| 1.3.6.1.4.1.17713.11.8.30 | ScalarlicenseSyncESupport | read-only | current | The license key SyncE support setting. |
| 1.3.6.1.4.1.17713.11.8.31 | ScalarlicenseIPv6Support | read-only | current | The license key IPv6 support setting. |
| 1.3.6.1.4.1.17713.11.8.32 | ScalarlicenseMinimumFirmwareVersion | read-only | current | The minimum firmware version required to support this license key. |
| 1.3.6.1.4.1.17713.11.8.33 | ScalarlicenseFullCapabilityTrialStatus | read-only | current | The license key full capability trial period status. |
| 1.3.6.1.4.1.17713.11.8.34 | ScalarlicenseRemainingTrialPeriod | read-only | current | The remaining time for the license key full capability trial period. |
| 1.3.6.1.4.1.17713.11.8.35 | ScalarlicenseRemainingTrialPeriodAlarm | read-only | current | If the full capability trial license period is about to expire then purchase a license upgrade from your reseller. |
| 1.3.6.1.4.1.17713.11.8.36 | ScalarcapacityVariantMismatchLinked | read-only | current | The remote node of this link has a lower link capacity. Operating with a reduced effective link capacity. |
| 1.3.6.1.4.1.17713.11.8.37 | ScalarlicenseTDDSyncSupport | read-only | current | The license key TDD Synchronization support setting. |
| 1.3.6.1.4.1.17713.11.8.38 | ScalarlicenseMaxLinkRange | read-only | current | Maximum licensed range for the wireless link in tenths of km. A value of zero indicates that the maximum link range is not limited by the license. |
| 1.3.6.1.4.1.17713.11.8.39 | ScalarlicenseTrialPeriod | read-only | current | The license key maximum trial period, in days. |
| 1.3.6.1.4.1.17713.11.8.40 | ScalarlicenseRARSupport | read-only | current | The license key Radio Aware Routing support setting. |
| 1.3.6.1.4.1.17713.11.8.41 | ScalarlicenseGasGroup | read-only | current | The HAZLOC/ATEX Configuration of this unit. The Gas Group is configured by the license key. |
| 1.3.6.1.4.1.17713.11.8.42 | ScalarlicenseLongMinimumFirmwareVersion | read-only | current | The minimum long firmware version required to support this license key. |
| 1.3.6.1.4.1.17713.11.8.43 | ScalarlicenseHCMPSupport | read-only | current | The license High Capacity MultiPoint support setting |
| 1.3.6.1.4.1.17713.11.8.44 | ScalarlicenseInstancedTableNumber | read-only | current | Number of entries in the licenseInstancedTable. |
| 1.3.6.1.4.1.17713.11.8.45 | TablelicenseInstancedTable | not-accessible | current | Instanced license table |
| 1.3.6.1.4.1.17713.11.8.45.1 | RowlicenseInstancedTableEntry | not-accessible | current | Table LicenseInstancedTable |
| 1.3.6.1.4.1.17713.11.8.45.1.1 | ColumnlicenseInstancedTableIndex | not-accessible | current | Used to index the LicenseInstancedTable. |
| 1.3.6.1.4.1.17713.11.8.45.1.2 | ColumncapacityVariantMismatch | read-only | current | The remote node of this link has a lower link capacity. Operating with a reduced effective link capacity. |
| 1.3.6.1.4.1.17713.11.8.46 | ScalarlicenseTLSRekey | read-only | current | The license TLS Rekey support setting |
| 1.3.6.1.4.1.17713.11.8.47 | ScalarlicenseAdvanceHCMPSupport | read-only | current | The license Advance High Capacity MultiPoint support setting |
| 1.3.6.1.4.1.17713.11.8.48 | ScalarlicenseMinFirmwareVersionPTP650Emulation | read-only | current | The minimum long firmware version of 650-Emulation required to support this license key. |
| 1.3.6.1.4.1.17713.11.9 | Nodemanagement | |||
| 1.3.6.1.4.1.17713.11.9.1 | ScalartargetRange | read-only | current | Initial target range used in installation +/-1, expressed in tenths of a kilometer. When Auto-Ranging this must be set to 0 |
| 1.3.6.1.4.1.17713.11.9.2 | ScalarrangingMode | read-only | current | Type of ranging to use during installation, either Auto-Ranging or use a selectable Target Range |
| 1.3.6.1.4.1.17713.11.9.3 | ScalarinstallStatusLinked | read-only | current | A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because un… |
| 1.3.6.1.4.1.17713.11.9.4 | ScalarinstallArmState | read-write | current | Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert |
| 1.3.6.1.4.1.17713.11.9.6 | ScalartFTPServerPortNumber | read-write | current | The port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved |
| 1.3.6.1.4.1.17713.11.9.7 | ScalartFTPSoftwareUpgradeFileName | read-write | current | Filename of the Software Upgrade to be loaded from the TFTP Server |
| 1.3.6.1.4.1.17713.11.9.8 | ScalartFTPStartSoftwareUpgrade | read-write | current | Write '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished. Continuing with… |
| 1.3.6.1.4.1.17713.11.9.9 | ScalartFTPSoftwareUpgradeStatus | read-only | current | The current status of the TFTP Software upgrade process |
| 1.3.6.1.4.1.17713.11.9.10 | ScalartFTPSoftwareUpgradeStatusText | read-only | current | Descriptive text describing the status of the TFTP Software upgrade process, including any error details |
| 1.3.6.1.4.1.17713.11.9.11 | ScalartFTPSoftwareUpgradeStatusAdditionalText | read-only | current | Any additional text describing the status of the TFTP Software upgrade process, including any error details |
| 1.3.6.1.4.1.17713.11.9.12 | ScalarhTTPAccessEnabled | read-write | current | This controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote manag… |
| 1.3.6.1.4.1.17713.11.9.13 | ScalartelnetAccessEnabled | read-write | current | This controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any chan… |
| 1.3.6.1.4.1.17713.11.9.14 | ScalarhTTPPortNumber | read-write | current | This controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit… |
| 1.3.6.1.4.1.17713.11.9.15 | ScalarhTTPSPortNumber | read-write | current | This controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the License Key. Any … |
| 1.3.6.1.4.1.17713.11.9.16 | ScalartelnetPortNumber | read-write | current | This controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the un… |
| 1.3.6.1.4.1.17713.11.9.17 | ScalarhTTPSAccessEnabled | read-write | current | This controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote man… |
| 1.3.6.1.4.1.17713.11.9.18 | ScalartFTPServerInternetAddressType | read-only | current | The type of Internet address specified by the associated tFTPServerInternetAddress. |
| 1.3.6.1.4.1.17713.11.9.19 | ScalartFTPServerInternetAddress | read-write | current | INET address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved |
| 1.3.6.1.4.1.17713.11.9.20 | ScalarlowestDataModulationMode | read-only | current | The lowest modulation mode at which Ethernet Data traffic will be bridged over the wireless link |
| 1.3.6.1.4.1.17713.11.9.22 | ScalartFTPClient | read-only | current | This controls whether or not TFTP client is enabled, i.e. if this is disabled (0) then the unit will not respond to any TFTP software download requests. (Facto… |
| 1.3.6.1.4.1.17713.11.9.23 | ScalarmgmtInstancedTableNumber | read-only | current | Number of entries in the mgmtInstancedTable. |
| 1.3.6.1.4.1.17713.11.9.24 | TablemgmtInstancedTable | not-accessible | current | Instanced management table. |
| 1.3.6.1.4.1.17713.11.9.24.1 | RowmgmtInstancedTableEntry | not-accessible | current | Table MgmtInstancedTable |
| 1.3.6.1.4.1.17713.11.9.24.1.1 | ColumnmgmtInstancedTableIndex | not-accessible | current | Used to index values in the mgmtInstancedTable |
| 1.3.6.1.4.1.17713.11.9.24.1.2 | ColumninstallStatus | read-only | current | A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because un… |
| 1.3.6.1.4.1.17713.11.9.25 | ScalartFTPServerResolvedInternetAddress | read-only | current | IP Address of the TFTP Server. |
| 1.3.6.1.4.1.17713.11.9.26 | ScalarinstallationMode | read-write | current | Determines whether the unit is armed for antenna alignment, and whether it emits audible installation tones to indicate the state and strength of the received … |
| 1.3.6.1.4.1.17713.11.10 | NodephyControl | |||
| 1.3.6.1.4.1.17713.11.10.1 | ScalarlinkSymmetry | read-only | current | Provides configuration options for sharing the available wireless capacity between the transmit and receive directions. Fixed link symmetry is defined by a rat… |
| 1.3.6.1.4.1.17713.11.10.2 | ScalaruserConfiguredMaxModulationMode | read-write | current | The maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation ag… |
| 1.3.6.1.4.1.17713.11.10.3 | ScalarlinkModeOptimization | read-only | current | Optimizes the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimize transmission errors by automa… |
| 1.3.6.1.4.1.17713.11.10.4 | ScalartxColorCode | read-only | current | Transmit Color Code. This attribute need only be considered when the unit is installed in a network of wireless units and where some of the units are operating… |
| 1.3.6.1.4.1.17713.11.10.5 | ScalarrxColorCode | read-only | current | Receive Color Code. This attribute need only be considered when the unit is installed in a network of wireless units and where some of the units are operating … |
| 1.3.6.1.4.1.17713.11.10.6 | ScalarremoteMaximumTransmitPowerLinked | read-only | current | Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link |
| 1.3.6.1.4.1.17713.11.10.7 | ScalarphyControlInstancedTableNumber | read-only | current | Number of entries in the PhyControlInstancedTable. |
| 1.3.6.1.4.1.17713.11.10.8 | TablephyControlInstancedTable | not-accessible | current | |
| 1.3.6.1.4.1.17713.11.10.8.1 | RowphyControlInstancedTableEntry | not-accessible | current | Table PhyControlInstancedTable |
| 1.3.6.1.4.1.17713.11.10.8.1.1 | ColumnphyControlInstancedTableIndex | not-accessible | current | Used to index the PhyControlInstancedTable. |
| 1.3.6.1.4.1.17713.11.10.8.1.2 | ColumnremoteMaximumTransmitPower | read-only | current | Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link |
| 1.3.6.1.4.1.17713.11.12 | NodephyStatus | |||
| 1.3.6.1.4.1.17713.11.12.1 | ScalarlinkLossLinked | read-only | current | The wireless link loss expressed in tenths of a dB |
| 1.3.6.1.4.1.17713.11.12.2 | ScalarreceivePowerLinked | read-only | current | Receive power expressed in tenths of a dBm |
| 1.3.6.1.4.1.17713.11.12.3 | ScalarvectorErrorLinked | read-only | current | The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude.… |
| 1.3.6.1.4.1.17713.11.12.4 | ScalartransmitPowerLinked | read-only | current | Transmit power expressed in tenths of a dBm |
| 1.3.6.1.4.1.17713.11.12.5 | ScalarreceiveChannel | read-only | current | Current active receive channel |
| 1.3.6.1.4.1.17713.11.12.6 | ScalartransmitChannel | read-only | current | Current active transmit channel |
| 1.3.6.1.4.1.17713.11.12.7 | ScalarreceiveFreqMHz | read-only | current | Current receive frequency expressed in integer MHz |
| 1.3.6.1.4.1.17713.11.12.8 | ScalartransmitFreqMHz | read-only | current | Current transmit frequency expressed in integer MHz |
| 1.3.6.1.4.1.17713.11.12.9 | ScalarsignalStrengthRatioLinked | read-only | current | Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of … |
| 1.3.6.1.4.1.17713.11.12.10 | ScalarreceiveFreqKHz | read-only | current | Current receive frequency expressed as KHz |
| 1.3.6.1.4.1.17713.11.12.11 | ScalartransmitFreqKHz | read-only | current | Current transmit frequency expressed as KHz |
| 1.3.6.1.4.1.17713.11.12.12 | ScalarrawReceivePowerLinked | read-only | current | Raw receive power expressed in tenths of a dBm |
| 1.3.6.1.4.1.17713.11.12.13 | ScalarrangeLinked | read-only | current | Distance between the two peer wireless units expressed in tenths of a kilometer |
| 1.3.6.1.4.1.17713.11.12.14 | ScalarreceiveModulationModeLinked | read-only | current | Current active receive modulation mode |
| 1.3.6.1.4.1.17713.11.12.15 | ScalartransmitModulationModeLinked | read-only | current | Current active transmit modulation mode |
| 1.3.6.1.4.1.17713.11.12.16 | ScalarsearchStateLinked | read-only | current | Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wi… |
| 1.3.6.1.4.1.17713.11.12.17 | ScalarremoteMACAddressLinked | read-only | current | MAC Address of the peer wireless unit |
| 1.3.6.1.4.1.17713.11.12.18 | ScalarphyInstancedStatusTableNumber | read-only | current | Number of entries in the phyInstancedStatusTable. |
| 1.3.6.1.4.1.17713.11.12.19 | TablephyInstancedStatusTable | not-accessible | current | Instanced PHY status table. |
| 1.3.6.1.4.1.17713.11.12.19.1 | RowphyInstancedStatusTableEntry | not-accessible | current | Table PhyInstancedStatusTable |
| 1.3.6.1.4.1.17713.11.12.19.1.1 | ColumnphyInstancedStatusTableIndex | not-accessible | current | Used to index the phyInstancedStatusTable. |
| 1.3.6.1.4.1.17713.11.12.19.1.2 | ColumnlinkLoss | read-only | current | The link loss measurement = Peer Tx_Power(dBm) - Local Rx_Power(dBm) + 2 x Antenna_Pattern(dBi) |
| 1.3.6.1.4.1.17713.11.12.19.1.3 | ColumnreceivePower | read-only | current | Receive power histogram |
| 1.3.6.1.4.1.17713.11.12.19.1.4 | ColumnvectorError | read-only | current | The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude |
| 1.3.6.1.4.1.17713.11.12.19.1.5 | ColumnsignalStrengthRatio | read-only | current | Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input |
| 1.3.6.1.4.1.17713.11.12.19.1.6 | Columnrange | read-only | current | Distance between the two peer wireless units |
| 1.3.6.1.4.1.17713.11.12.19.1.7 | ColumnreceiveModulationMode | read-only | current | Current active receive modulation mode |
| 1.3.6.1.4.1.17713.11.12.19.1.8 | ColumntransmitModulationMode | read-only | current | Current active transmit modulation mode |
| 1.3.6.1.4.1.17713.11.12.19.1.9 | ColumnsearchState | read-only | current | Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wi… |
| 1.3.6.1.4.1.17713.11.12.19.1.10 | ColumnremoteMACAddress | read-only | current | MAC Address of the peer wireless unit |
| 1.3.6.1.4.1.17713.11.12.19.1.11 | ColumnrawReceivePower | read-only | current | Raw receive power |
| 1.3.6.1.4.1.17713.11.12.19.1.12 | ColumntransmitPower | read-only | current | Transmit power histogram |
| 1.3.6.1.4.1.17713.11.12.20 | ScalartempPcb | read-only | current | PCB temperature expressed in Celsius |
| 1.3.6.1.4.1.17713.11.13 | Nodealarms | |||
| 1.3.6.1.4.1.17713.11.13.1 | ScalarunitOutOfCalibration | read-only | current | The unit is out of calibration |
| 1.3.6.1.4.1.17713.11.13.4 | ScalarincompatibleRegulatoryBandsLinked | read-only | current | The master and slave units have incompatible regulatory bands. NB: Both units must have compatible license keys |
| 1.3.6.1.4.1.17713.11.13.5 | ScalarnoWirelessChannelAvailable | read-only | current | Spectrum Management was unable to locate a suitable wireless channel to operate on |
| 1.3.6.1.4.1.17713.11.13.6 | ScalarwirelessLinkDisabledWarning | read-only | current | The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic |
| 1.3.6.1.4.1.17713.11.13.7 | ScalarmainPSUPortDisabledWarning | read-only | current | The SNMP ifAdminStatus of the interface has disabled Ethernet traffic |
| 1.3.6.1.4.1.17713.11.13.8 | ScalarsFPError | read-only | current | If the SFP link is not OK, there are five possible causes: Either a SFP has been installed but the license key does not include SFP fiber support, a fiber link… |
| 1.3.6.1.4.1.17713.11.13.9 | ScalarmainPSUPortConfigurationMismatch | read-only | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch |
| 1.3.6.1.4.1.17713.11.13.10 | ScalarincompatibleMasterAndSlaveLinked | read-only | current | A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions, or have different TDD… |
| 1.3.6.1.4.1.17713.11.13.11 | ScalartDDSynchronizationStatus | read-only | current | An alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing… |
| 1.3.6.1.4.1.17713.11.13.12 | ScalarauxPortDisabledWarning | read-only | current | The SNMP ifAdminStatus of the interface has disabled Ethernet traffic |
| 1.3.6.1.4.1.17713.11.13.13 | ScalartDDSynchronizationAlarm | read-only | current | Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this lin… |
| 1.3.6.1.4.1.17713.11.13.14 | ScalarlinkModeOptimizationMismatchLinked | read-only | current | The remote node of this link has been configured with a different link mode optimization |
| 1.3.6.1.4.1.17713.11.13.15 | ScalarauxPortConfigurationMismatch | read-only | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. Th… |
| 1.3.6.1.4.1.17713.11.13.16 | ScalarsecureModeAlarm | read-only | current | The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, … |
| 1.3.6.1.4.1.17713.11.13.17 | ScalardataBridgingStatusAlarmLinked | read-only | current | Ethernet Data traffic bridging is disabled because the wireless link is not operating at the configured Lowest Data Modulation Mode |
| 1.3.6.1.4.1.17713.11.13.18 | ScalarsFPPortDisabledWarning | read-only | current | The SNMP ifAdminStatus of the interface has disabled Ethernet traffic |
| 1.3.6.1.4.1.17713.11.13.19 | ScalarsFPPortConfigurationMismatch | read-only | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. Th… |
| 1.3.6.1.4.1.17713.11.13.20 | ScalarmaxLinkRangeExceededLinked | read-only | current | The measured link range is greater than the maximum allowed by the license key. The link will operate at a reduced capacity while this condition applies. This … |
| 1.3.6.1.4.1.17713.11.13.21 | ScalarnIDULanPortDisabledWarning | read-only | current | The SNMP ifAdminStatus of the interface has disabled Ethernet traffic |
| 1.3.6.1.4.1.17713.11.13.22 | ScalarnIDULanPortConfigurationMismatch | read-only | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. |
| 1.3.6.1.4.1.17713.11.13.23 | ScalarportAllocationMismatchLinked | read-only | current | The local and remote ODUs have different services configured. |
| 1.3.6.1.4.1.17713.11.13.25 | ScalartransparentClockSourcePortAlarm | read-only | current | Transparent Clock will not function properly because SFP, the selected clock source port is not FIBER |
| 1.3.6.1.4.1.17713.11.13.26 | ScalaralarmInstancedTableNumber | read-only | current | Number of entries in the alarmInstancedTable. |
| 1.3.6.1.4.1.17713.11.13.27 | TablealarmInstancedTable | not-accessible | current | Instanced alarm table. |
| 1.3.6.1.4.1.17713.11.13.27.1 | RowalarmInstancedTableEntry | not-accessible | current | Table AlarmInstancedTable |
| 1.3.6.1.4.1.17713.11.13.27.1.1 | ColumnalarmInstancedTableIndex | not-accessible | current | Used to index values in the alarmInstancedTable |
| 1.3.6.1.4.1.17713.11.13.27.1.2 | ColumnincompatibleMasterAndSlave | read-only | current | A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions, or have different TDD… |
| 1.3.6.1.4.1.17713.11.13.27.1.3 | ColumnlinkModeOptimizationMismatch | read-only | current | The remote node of this link has been configured with a different link mode optimization |
| 1.3.6.1.4.1.17713.11.13.27.1.4 | ColumndataBridgingStatusAlarm | read-only | current | Ethernet Data traffic bridging is disabled because the wireless link is not operating at the configured Lowest Data Modulation Mode |
| 1.3.6.1.4.1.17713.11.13.27.1.5 | ColumnmaxLinkRangeExceeded | read-only | current | The measured link range is greater than the maximum allowed by the license key. The link will operate at a reduced capacity while this condition applies. This … |
| 1.3.6.1.4.1.17713.11.13.27.1.6 | ColumnportAllocationMismatch | read-only | current | The local and remote ODUs have different services configured. |
| 1.3.6.1.4.1.17713.11.13.27.1.7 | ColumnwirelessLinkStatusAlarm | read-only | current | Current status of the wireless link. A state of Up on a green background indicates that a wireless link is established |
| 1.3.6.1.4.1.17713.11.13.27.1.8 | ColumnincompatibleRegulatoryBands | read-only | current | The master and slave units have incompatible regulatory bands. NB: Both units must have compatible license keys |
| 1.3.6.1.4.1.17713.11.13.28 | ScalarsecureLicenseSignatureAlarm | read-only | current | Alarm condition indicates that the unit's license is not secure enough for FIPS approved mode. |
| 1.3.6.1.4.1.17713.11.14 | Nodeapc | |||
| 1.3.6.1.4.1.17713.11.14.1 | ScalaratpcHcmpMasterTargetRxPower | read-only | current | The target Rx power level (dBm) at the HCMP Master that the HCMP Slaves try to reach by automatically adjusting their transmit power. The same value must be se… |
| 1.3.6.1.4.1.17713.11.14.2 | ScalaratpcHcmpMasterTxPower | read-only | current | This must be set to the same value as the Maximum Transmit Power attribute on the HCMP Master. This is required by the HCMP Slave for initial transmit power es… |
| 1.3.6.1.4.1.17713.11.15 | Nodesmtp | |||
| 1.3.6.1.4.1.17713.11.15.1 | ScalarsMTPEmailAlert | read-write | current | Simple Mail Transfer Protocol is used to send equipment alerts via email to a specified email address |
| 1.3.6.1.4.1.17713.11.15.3 | ScalarsMTPServerPortNumber | read-write | current | Port number of the SMTP server |
| 1.3.6.1.4.1.17713.11.15.4 | ScalarsMTPSourceEmailAddress | read-write | current | The 'from' email address used when constructing the automatically generated e-mail message |
| 1.3.6.1.4.1.17713.11.15.5 | ScalarsMTPDestinationEmailAddress | read-write | current | The 'to' email address used when constructing the automatically generated e-mail message |
| 1.3.6.1.4.1.17713.11.15.6 | ScalarsMTPEnabledMessages | read-write | current | This controls which SMTP messages the unit will send |
| 1.3.6.1.4.1.17713.11.15.7 | ScalarsMTPServerInternetAddressType | read-only | current | The type of Internet address specified by the associated sMTPServerInternetAddress. |
| 1.3.6.1.4.1.17713.11.15.8 | ScalarsMTPServerInternetAddress | read-write | current | Internet address of the SMTP server |
| 1.3.6.1.4.1.17713.11.15.9 | ScalarsMTPServerResolvedInternetAddress | read-only | current | IP Address of the SMTP Server. |
| 1.3.6.1.4.1.17713.11.16 | NodesnmpControl | |||
| 1.3.6.1.4.1.17713.11.16.1 | ScalarsNMPPortNumber | read-write | current | The IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attribute |
| 1.3.6.1.4.1.17713.11.16.2 | ScalarsNMPCommunityString | read-write | current | The SNMP community string. NB: A system reboot is required to activate changes to this attribute |
| 1.3.6.1.4.1.17713.11.16.3 | ScalarsNMPTrapTableNumber | read-only | current | Number of entries in the sNMPTrapTable. |
| 1.3.6.1.4.1.17713.11.16.4 | TablesNMPTrapTable | not-accessible | current | SNMP trap configuration table. |
| 1.3.6.1.4.1.17713.11.16.4.1 | RowsNMPTrapTableEntry | not-accessible | current | Table SNMPTrapTable |
| 1.3.6.1.4.1.17713.11.16.4.1.1 | ColumnsNMPTrapTableIndex | not-accessible | current | SNMP trap value, used to index the SNMPTrapTable. |
| 1.3.6.1.4.1.17713.11.16.4.1.3 | ColumnsNMPTrapPortNumber | read-write | current | Destination port for SNMP Traps (default=162). NB: A system reboot is required to activate changes to this attribute. |
| 1.3.6.1.4.1.17713.11.16.4.1.4 | ColumnsNMPTrapInternetAddressType | read-only | current | The type of Internet address specified by the associated sNMPTrapInternetAddress. |
| 1.3.6.1.4.1.17713.11.16.4.1.5 | ColumnsNMPTrapInternetAddress | read-write | current | The Internet address to which all SNMP Traps are sent. |
| 1.3.6.1.4.1.17713.11.16.4.1.6 | ColumnsNMPTrapReceiverEnabled | read-write | current | A value of 0 disables the sending of SNMP trap to corresponding receiver. A value of 1 enables the sending of SNMP trap to corresponding receiver. |
| 1.3.6.1.4.1.17713.11.16.4.1.7 | ColumnsNMPTrapResolvedInternetAddress | read-only | current | IP Address(es) of the SNMP Trap Server. |
| 1.3.6.1.4.1.17713.11.16.5 | ScalarsNMPTrapVersion | read-write | current | The SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attribute |
| 1.3.6.1.4.1.17713.11.16.6 | ScalarsNMPEnabledTraps | read-write | current | This controls which SNMP Traps the unit will send |
| 1.3.6.1.4.1.17713.11.16.7 | ScalarenabledDiagnosticAlarms | read-write | current | Controls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by… |
| 1.3.6.1.4.1.17713.11.16.8 | ScalarsNMPSendAllTrapsAtStartup | read-write | current | Controls whether cleared traps are reported at start-up as well as raised traps. Only enabled traps will be reported. NB: Traps corresponding to transient even… |
| 1.3.6.1.4.1.17713.11.17 | Nodesntp | |||
| 1.3.6.1.4.1.17713.11.17.1 | ScalarsNTPState | read-write | current | SNTP control state |
| 1.3.6.1.4.1.17713.11.17.4 | ScalarsNTPPollInterval | read-write | current | The SNTP server polling interval |
| 1.3.6.1.4.1.17713.11.17.5 | ScalarsNTPSync | read-only | current | If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP |
| 1.3.6.1.4.1.17713.11.17.6 | ScalarsNTPLastSync | read-only | current | Last SNTP sync time |
| 1.3.6.1.4.1.17713.11.17.7 | ScalarsystemClock | read-only | current | System clock presented as local time |
| 1.3.6.1.4.1.17713.11.17.8 | ScalartimeZone | read-write | current | Time zone offsets from Greenwich Mean Time (GMT) |
| 1.3.6.1.4.1.17713.11.17.9 | ScalardaylightSaving | read-write | current | Daylight Saving Time |
| 1.3.6.1.4.1.17713.11.17.10 | ScalarsNTPPrimaryServer | read-write | current | Specifies the primary SNTP server, determining the order in which the servers are tried. |
| 1.3.6.1.4.1.17713.11.17.11 | ScalarsNTPPrimaryServerDeadTime | read-write | current | Time (in seconds) to wait before retrying communications with an unresponsive primary SNTP server. Setting the value to 0 disables the timer. |
| 1.3.6.1.4.1.17713.11.17.12 | ScalarsNTPServerRetries | read-write | current | Number of times the device will retry after an SNTP server fails to respond. |
| 1.3.6.1.4.1.17713.11.17.13 | ScalarsNTPServerTimeout | read-write | current | Time (in seconds) the device will wait for a response from an SNTP server. |
| 1.3.6.1.4.1.17713.11.17.14 | ScalarsNTPServerTableNumber | read-only | current | Number of entries in the SNTPServerTable. |
| 1.3.6.1.4.1.17713.11.17.15 | TablesNTPServerTable | not-accessible | current | |
| 1.3.6.1.4.1.17713.11.17.15.1 | RowsNTPServerTableEntry | not-accessible | current | Table SNTPServerTable |
| 1.3.6.1.4.1.17713.11.17.15.1.1 | ColumnsNTPServerTableIndex | not-accessible | current | Index range for the SNTPServerTable. |
| 1.3.6.1.4.1.17713.11.17.15.1.3 | ColumnsNTPServerPortNumber | read-write | current | The IP port number of the SNTP server. Defaults to port 123. |
| 1.3.6.1.4.1.17713.11.17.15.1.4 | ColumnsNTPServerStatus | read-only | current | Status message reflecting the result of communications with the SNTP server when last polled |
| 1.3.6.1.4.1.17713.11.17.15.1.5 | ColumnsNTPServerInternetAddressType | read-only | current | The type of Internet address specified by the associated sNTPServerInternetAddress. |
| 1.3.6.1.4.1.17713.11.17.15.1.6 | ColumnsNTPServerInternetAddress | read-write | current | The Internet address of a valid SNTP server |
| 1.3.6.1.4.1.17713.11.17.15.1.7 | ColumnsNTPServerResolvedInternetAddress | read-only | current | IP Address of the SNTP Server. |
| 1.3.6.1.4.1.17713.11.17.15.1.8 | ColumnsNTPServerAuthenticationProtocol | read-only | current | Authentication protocol to be used for this SNTP server. Options are None (default) or MD5. |
| 1.3.6.1.4.1.17713.11.17.15.1.9 | ColumnsNTPServerKeyIdentifier | read-only | current | SNTP key identifier. Note: Key 0 is reserved for testing using the well-known key all zeroes. |
| 1.3.6.1.4.1.17713.11.18 | Nodereset | |||
| 1.3.6.1.4.1.17713.11.18.1 | ScalarsystemReset | read-write | current | Setting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memory |
| 1.3.6.1.4.1.17713.11.19 | Nodeversions | |||
| 1.3.6.1.4.1.17713.11.19.1 | ScalarsoftwareVersion | read-only | current | Current software version |
| 1.3.6.1.4.1.17713.11.19.2 | ScalarhardwareVersion | read-only | current | Hardware platform version |
| 1.3.6.1.4.1.17713.11.19.3 | ScalarsecondarySoftwareVersion | read-only | current | Secondary software version, used when the primary software image is invalid or erased |
| 1.3.6.1.4.1.17713.11.19.4 | ScalarbootVersion | read-only | current | Boot code software version |
| 1.3.6.1.4.1.17713.11.20 | NodepubStats | |||
| 1.3.6.1.4.1.17713.11.20.1 | ScalarreceiveDataRateLinked | read-only | current | Average data rate over the last one second interval (kbps) |
| 1.3.6.1.4.1.17713.11.20.2 | ScalartransmitDataRateLinked | read-only | current | Average data rate over the last one second interval (kbps) |
| 1.3.6.1.4.1.17713.11.20.3 | ScalaraggregateDataRateLinked | read-only | current | Average data rate over the last one second interval (kbps) |
| 1.3.6.1.4.1.17713.11.20.4 | ScalarwirelessLinkAvailabilityLinked | read-only | current | Link availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision |
| 1.3.6.1.4.1.17713.11.20.5 | ScalarwirelessLinkStatusLinked | read-only | current | Current status of the wireless link |
| 1.3.6.1.4.1.17713.11.20.6 | ScalarbyteErrorRatioLinked | read-only | current | Reciprocal of the byte error ratio calculated since the last reset of the system counters |
| 1.3.6.1.4.1.17713.11.20.7 | ScalarreceiveModulationModeDetailLinked | read-only | current | The reason for the current receive modulation mode |
| 1.3.6.1.4.1.17713.11.20.8 | ScalardataBridgingAvailabilityLinked | read-only | current | Link availability bridging Ethernet Data traffic calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decim… |
| 1.3.6.1.4.1.17713.11.20.9 | ScalarpubInstancedStatsTableNumber | read-only | current | Number of entries in the pubInstancedStatsTable. |
| 1.3.6.1.4.1.17713.11.20.10 | TablepubInstancedStatsTable | not-accessible | current | Instanced Public stats table. |
| 1.3.6.1.4.1.17713.11.20.10.1 | RowpubInstancedStatsTableEntry | not-accessible | current | Table PubInstancedStatsTable |
| 1.3.6.1.4.1.17713.11.20.10.1.1 | ColumnpubInstancedStatsTableIndex | not-accessible | current | Used to index the pubInstancedStatsTable. |
| 1.3.6.1.4.1.17713.11.20.10.1.2 | ColumnreceiveDataRate | read-only | current | Histogram of the average link receive data rate. |
| 1.3.6.1.4.1.17713.11.20.10.1.3 | ColumntransmitDataRate | read-only | current | Histogram of the average link transmit data rate. |
| 1.3.6.1.4.1.17713.11.20.10.1.4 | ColumnaggregateDataRate | read-only | current | Histogram of the link aggregate data rate. |
| 1.3.6.1.4.1.17713.11.20.10.1.5 | ColumnwirelessLinkAvailability | read-only | current | Link availability calculated since the last reset of the system counters |
| 1.3.6.1.4.1.17713.11.20.10.1.6 | ColumnwirelessLinkStatus | read-only | current | Current status of the wireless link. A state of 'Up' on a green background indicates that a wireless link is established |
| 1.3.6.1.4.1.17713.11.20.10.1.7 | ColumnreceiveModulationModeDetail | read-only | current | A brief description of the reason for the current receive modulation mode |
| 1.3.6.1.4.1.17713.11.20.10.1.8 | ColumndataBridgingAvailability | read-only | current | Link availability for bridging Ethernet Data traffic calculated since the last reset of the system counters |
| 1.3.6.1.4.1.17713.11.20.10.1.9 | ColumnbyteErrorRatio | read-only | current | Reciprocal of the byte error ratio calculated since the last reset of the system counters |
| 1.3.6.1.4.1.17713.11.20.10.1.10 | ColumnwirelessOutEthernetOctets | read-only | current | Cumulative total of octets transmitted in data or management service at the wireless interface. This excludes wireless MAC headers, MAC management messages, an… |
| 1.3.6.1.4.1.17713.11.20.10.1.11 | ColumnwirelessOutAllOctets | read-only | current | Cumulative total of octets transmitted at the wireless interface. This includes data service, management service, wireless MAC headers, MAC management messages… |
| 1.3.6.1.4.1.17713.11.20.10.1.12 | ColumnwirelessOutOctets | read-only | current | Cumulative total of octets including wireless MAC headers transmitted in data or management service at the wireless interface. This excludes MAC management mes… |
| 1.3.6.1.4.1.17713.11.20.10.1.13 | ColumnerroredSeconds | read-only | current | erroredSeconds count for any second period containing one or more codeword errors since the last reset of the system counters. |
| 1.3.6.1.4.1.17713.11.20.10.1.14 | ColumnseverelyErroredSeconds | read-only | current | severelyErroredSeconds count for any second period containing ten or more codeword errors since the last reset of the system counters. |
| 1.3.6.1.4.1.17713.11.20.10.1.15 | ColumnunavailableSeconds | read-only | current | unavailableSeconds count for any second when Data Bridging Status = Disabled since the last reset of the system counters. Note erroredSeconds and severelyError… |
| 1.3.6.1.4.1.17713.11.22 | Nodeencryption | |||
| 1.3.6.1.4.1.17713.11.22.1 | ScalarencryptionAlgorithm | read-only | current | The Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm mu… |
| 1.3.6.1.4.1.17713.11.22.2 | ScalartLSMinimumSecurityLevel | read-only | current | The minimum level of security that is supported on the device |
| 1.3.6.1.4.1.17713.11.23 | NodetDDControl | |||
| 1.3.6.1.4.1.17713.11.23.1 | ScalartDDSynchronizationMode | read-only | current | TDD Synchronization Mode selection |
| 1.3.6.1.4.1.17713.11.23.2 | ScalarhCMPMaximumLinkRange | read-only | current | The maximum link range between the HCMP Master and any HCMP Slave. The same value must be used on both the HCMP Master and its Slaves. |
| 1.3.6.1.4.1.17713.11.23.3 | ScalarmaximumNumberOfSlaves | read-only | current | The maximum number of HCMP Slaves that an HCMP Master can simultaneously connect to. The same value has to be used in both the HCMP Master and its Slaves. |
| 1.3.6.1.4.1.17713.11.23.4 | ScalarhCMPLinkSymmetry | read-only | current | Provides configuration options for sharing the available wireless capacity among all Slaves between the transmit and receive directions. Option x to y is the r… |
| 1.3.6.1.4.1.17713.11.24 | NodesyslogControl | |||
| 1.3.6.1.4.1.17713.11.24.1 | ScalarsyslogClient | read-only | current | Enable or disable the syslog client |
| 1.3.6.1.4.1.17713.11.24.2 | ScalarsyslogState | read-only | current | The syslog service has been enabled or disabled |
| 1.3.6.1.4.1.17713.11.25 | NodeaAAControl | |||
| 1.3.6.1.4.1.17713.11.25.1 | ScalaruserTableNumber | read-only | current | Number of entries in the userTable |
| 1.3.6.1.4.1.17713.11.25.2 | TableuserTable | not-accessible | current | The User Table Control group contains objects specifically for user account management. |
| 1.3.6.1.4.1.17713.11.25.2.1 | RowuserTableEntry | not-accessible | current | Table UserTable |
| 1.3.6.1.4.1.17713.11.25.2.1.1 | ColumnuserTableIndex | not-accessible | current | used to index values in the userTable. |
| 1.3.6.1.4.1.17713.11.25.2.1.2 | ColumnuserName | read-only | current | User name which must be entered, along with the appropriate password, in order to gain access to the system. |
| 1.3.6.1.4.1.17713.11.25.2.1.3 | ColumnuserRole | read-only | current | Role of the selected user. A Security Officer has access to and can modify all settings. A System Administrator has access to and can modify all non-security s… |
| 1.3.6.1.4.1.17713.11.25.2.1.4 | ColumnuserEnabled | read-only | current | Enable / Disable the selected user |
| 1.3.6.1.4.1.17713.11.25.2.1.5 | ColumnuserPassword | read-write | current | User password, which must be entered in order to gain access to the system. |
| 1.3.6.1.4.1.17713.11.26 | NoderouterProtocols | |||
| 1.3.6.1.4.1.17713.11.26.1 | ScalarmicrowaveAdaptiveBandwidth | read-only | current | Enable support of Microwave Adaptive Bandwidth Protocol. MAB is disabled if link symmetry is configured as Adaptive |
| 1.3.6.1.4.1.17713.11.26.2 | ScalarmABNominalModulationMode | read-only | current | The Nominal modulation mode is the desired modulation mode. MAB VSM packets are generated when the current modulation mode falls below the nominal modulation. |
| 1.3.6.1.4.1.17713.11.26.3 | ScalarmABTransmissionInterval | read-only | current | The minimum interval (in seconds) between successive MAB vendor specific messages (VSM). These VSM are sent when the current transmit capacity falls below the … |
| 1.3.6.1.4.1.17713.11.26.4 | ScalarmABHoldoffPeriod | read-only | current | The period (in seconds) over which transmit capacity is averaged over to determine when the wireless link has degraded |
| 1.3.6.1.4.1.17713.11.26.5 | ScalarmABMaintenanceLevel | read-only | current | Maintenance Levels (0-7) determines the destination MAC address of MAB vendor specific messages. |
| 1.3.6.1.4.1.17713.11.26.6 | ScalaruseVLANForMABProtocol | read-only | current | This controls whether MAB vendor specific messages (VSM) packets use VLAN tags or not. |
| 1.3.6.1.4.1.17713.11.26.7 | ScalarmABProtocolVID | read-only | current | This VLAN VID (0-4094) will be included in MAB vendor specific messages (VSM) packets. |
| 1.3.6.1.4.1.17713.11.26.8 | ScalarmABProtocolVLANPriority | read-only | current | This VLAN Priority (0-7) will be included in MAB vendor specific messages (VSM) packets. |
| 1.3.6.1.4.1.17713.11.26.9 | ScalarmABState | read-only | current | Current state of MAB Protocol. A state of 'Normal' on a green background indicates that a wireless link is operating at nominal capacity |
| 1.3.6.1.4.1.17713.11.26.10 | ScalarmABNominalTransmitCapacity | read-only | current | The nominal Tx capacity used in MAB Vendor Specific Messages for the selected nominal modulation mode |
| 1.3.6.1.4.1.17713.11.26.11 | ScalarmABCurrentTransmitCapacity | read-only | current | The current Tx capacity of the wireless link used in the last MAB Vendor Specific Message transmitted. |
| 1.3.6.1.4.1.17713.11.27 | NodecableDiagnostics | |||
| 1.3.6.1.4.1.17713.11.27.1 | ScalarcableDiagnosticsPorts | read-write | current | Select ports on which Cable Diagnostics must be executed |
| 1.3.6.1.4.1.17713.11.27.2 | ScalarcableDiagnosticsControl | read-write | current | Set this attribute to 'Test in Progress' to start a Cable Diagnostics test |
| 1.3.6.1.4.1.17713.11.27.3 | ScalarcableDiagnosticsWarning | read-only | current | Normal Ethernet operation is disrupted when a Cable Diagnostics test is in progress |
| 1.3.6.1.4.1.17713.11.27.4 | ScalarcableDiagnosticsResultTableNumber | read-only | current | Number of rows in the Cable Diagnostics Result Table. |
| 1.3.6.1.4.1.17713.11.27.5 | TablecableDiagnosticsResultTable | not-accessible | current | |
| 1.3.6.1.4.1.17713.11.27.5.1 | RowcableDiagnosticsResultTableEntry | not-accessible | current | Table CableDiagnosticsResultTable |
| 1.3.6.1.4.1.17713.11.27.5.1.1 | ColumncableDiagnosticsResultTableIndex | not-accessible | current | Cable Diagnostics Port value used to index into the result table. |
| 1.3.6.1.4.1.17713.11.27.5.1.2 | ColumncableDiagnosticsResultsDateTime | read-only | current | The Date and Time when a Cable Diagnostics test was last executed |
| 1.3.6.1.4.1.17713.11.27.5.1.3 | ColumncableDiagPair1Results | read-only | current | The result of the most recent execution of Cable Diagnostics on cable pair 1. According to the T658B wiring scheme, pair 1 is pins 4 & 5 on the RJ45 socket on … |
| 1.3.6.1.4.1.17713.11.27.5.1.4 | ColumncableDiagPair1Distance | read-only | current | The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than… |
| 1.3.6.1.4.1.17713.11.27.5.1.5 | ColumncableDiagPair2Results | read-only | current | The result of the most recent execution of Cable Diagnostics on cable pair 2. According to the T658B wiring scheme, pair 2 is pins 1 & 2 on the RJ45 socket on … |
| 1.3.6.1.4.1.17713.11.27.5.1.6 | ColumncableDiagPair2Distance | read-only | current | The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than… |
| 1.3.6.1.4.1.17713.11.27.5.1.7 | ColumncableDiagPair3Results | read-only | current | The result of the most recent execution of Cable Diagnostics on cable pair 3. According to the T658B wiring scheme, pair 3 is pins 3 & 6 on the RJ45 socket on … |
| 1.3.6.1.4.1.17713.11.27.5.1.8 | ColumncableDiagPair3Distance | read-only | current | The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than… |
| 1.3.6.1.4.1.17713.11.27.5.1.9 | ColumncableDiagPair4Results | read-only | current | The result of the most recent execution of Cable Diagnostics on cable pair 4. According to the T658B wiring scheme, pair 4 is pins 7 & 8 on the RJ45 socket on … |
| 1.3.6.1.4.1.17713.11.27.5.1.10 | ColumncableDiagPair4Distance | read-only | current | The distance in meters from the ODU to the fault detected on the cable pair during the most recent execution of Cable Diagnostics. Faults in cables longer than… |
| 1.3.6.1.4.1.17713.11.28 | NodeunitIdentification | |||
| 1.3.6.1.4.1.17713.11.28.1 | ScalardeviceMACAddress | read-only | current | Device MAC address |
| 1.3.6.1.4.1.17713.11.28.2 | ScalardeviceESN | read-only | current | The ESN assigned to this device |
| 1.3.6.1.4.1.17713.11.28.3 | ScalardeviceMSN | read-only | current | The MSN assigned to this device |
| 1.3.6.1.4.1.17713.11.29 | NodeauthorizationControl | |||
| 1.3.6.1.4.1.17713.11.29.1 | ScalarauthorizationControlTableNumber | read-only | current | Number of entries in the AuthorizationControlTable. |
| 1.3.6.1.4.1.17713.11.29.2 | TableauthorizationControlTable | not-accessible | current | AuthorizationControlTable - used to validate an RM trying to connect to it. |
| 1.3.6.1.4.1.17713.11.29.2.1 | RowauthorizationControlTableEntry | not-accessible | current | Table AuthorizationControlTable |
| 1.3.6.1.4.1.17713.11.29.2.1.1 | ColumnauthorizationControlTableIndex | not-accessible | current | Authorization Control Table Index |
| 1.3.6.1.4.1.17713.11.29.2.1.2 | ColumnwhitelistRMMacAddress | read-write | current | MAC Address of Remote Modules. |
| 1.3.6.1.4.1.17713.11.29.2.1.3 | ColumnwhitelistRMEnabled | read-write | current | Whether this Remote Module is enabled. Only Enabled Remote Modules are allowed to connect to this device. |
| 1.3.6.1.4.1.17713.11.29.2.1.4 | ColumnblacklistRMMacAddress | read-write | current | MAC Address of Remote Modules. |
| 1.3.6.1.4.1.17713.11.29.2.1.5 | ColumnblacklistRMEnabled | read-write | current | Whether this Remote Module is enabled. Only Enabled Remote Modules are black listed; they cannot connect to this ODU. |
| 1.3.6.1.4.1.17713.11.30 | NodedNS | |||
| 1.3.6.1.4.1.17713.11.30.1 | ScalardNSResolver | read-write | current | Enable/Disable DNS Resolver. |
| 1.3.6.1.4.1.17713.11.30.2 | ScalardNSPrimaryServer | read-only | current | Specifies the primary DNS server, determining the order in which the servers are tried. |
| 1.3.6.1.4.1.17713.11.30.3 | ScalardNSServerTableNumber | read-only | current | Number of entries in the DNSServerTable. |
| 1.3.6.1.4.1.17713.11.30.4 | TabledNSServerTable | not-accessible | current | |
| 1.3.6.1.4.1.17713.11.30.4.1 | RowdNSServerTableEntry | not-accessible | current | Table DNSServerTable |
| 1.3.6.1.4.1.17713.11.30.4.1.1 | ColumndNSServerTableIndex | not-accessible | current | Index range for the DNSServerTable. |
| 1.3.6.1.4.1.17713.11.30.4.1.2 | ColumndNSServerInternetAddressType | read-only | current | The type of Internet address specified by the associated dNSServerInternetAddress. |
| 1.3.6.1.4.1.17713.11.30.4.1.3 | ColumndNSServerInternetAddress | read-write | current | IP Address of the DNS Server which will be used to resolve hostname into IP Addresses . |
| 1.3.6.1.4.1.17713.11.30.4.1.4 | ColumndNSServerPortNumber | read-write | current | UDP Port Number of DNS Service on the Server. |
| 1.3.6.1.4.1.17713.11.96 | Nodesupplementary | |||
| 1.3.6.1.4.1.17713.11.96.1 | Scalarlongitude | read-write | current | The longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function. |
| 1.3.6.1.4.1.17713.11.96.2 | Scalarlatitude | read-write | current | The latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function. |
| 1.3.6.1.4.1.17713.11.96.3 | Scalaraltitude | read-write | current | The altitude of the unit, measured in meters. This object is set by the SNMP manager and has no internal function. |
| 1.3.6.1.4.1.17713.11.97 | ComplianceptpCompliance | current | The compliance statement for the Cambium PTP MIB | |
| 1.3.6.1.4.1.17713.11.98 | NodeptpGroups | |||
| 1.3.6.1.4.1.17713.11.98.3 | GroupdfsGroup | current | The dfs object group. | |
| 1.3.6.1.4.1.17713.11.98.4 | GroupbridgeGroup | current | The bridge object group. | |
| 1.3.6.1.4.1.17713.11.98.5 | GroupconfigurationGroup | current | The configuration object group. | |
| 1.3.6.1.4.1.17713.11.98.6 | GroupethernetGroup | current | The ethernet object group. | |
| 1.3.6.1.4.1.17713.11.98.7 | GrouptDMGroup | current | The tDM object group. | |
| 1.3.6.1.4.1.17713.11.98.8 | GrouplicenseGroup | current | The license object group. | |
| 1.3.6.1.4.1.17713.11.98.9 | GroupmanagementGroup | current | The management object group. | |
| 1.3.6.1.4.1.17713.11.98.10 | GroupphyControlGroup | current | The phyControl object group. | |
| 1.3.6.1.4.1.17713.11.98.12 | GroupphyStatusGroup | current | The phyStatus object group. | |
| 1.3.6.1.4.1.17713.11.98.13 | GroupalarmsGroup | current | The alarms object group. | |
| 1.3.6.1.4.1.17713.11.98.14 | GroupapcGroup | current | The apc object group. | |
| 1.3.6.1.4.1.17713.11.98.15 | GroupsmtpGroup | current | The smtp object group. | |
| 1.3.6.1.4.1.17713.11.98.16 | GroupsnmpControlGroup | current | The snmpControl object group. | |
| 1.3.6.1.4.1.17713.11.98.17 | GroupsntpGroup | current | The sntp object group. | |
| 1.3.6.1.4.1.17713.11.98.18 | GroupresetGroup | current | The reset object group. | |
| 1.3.6.1.4.1.17713.11.98.19 | GroupversionsGroup | current | The versions object group. | |
| 1.3.6.1.4.1.17713.11.98.20 | GrouppubStatsGroup | current | The pubStats object group. | |
| 1.3.6.1.4.1.17713.11.98.22 | GroupencryptionGroup | current | The encryption object group. | |
| 1.3.6.1.4.1.17713.11.98.23 | GrouptDDControlGroup | current | The tDDControl object group. | |
| 1.3.6.1.4.1.17713.11.98.24 | GroupsyslogControlGroup | current | The syslogControl object group. | |
| 1.3.6.1.4.1.17713.11.98.25 | GroupaAAControlGroup | current | The aAAControl object group. | |
| 1.3.6.1.4.1.17713.11.98.26 | GrouprouterProtocolsGroup | current | The routerProtocols object group. | |
| 1.3.6.1.4.1.17713.11.98.27 | GroupcableDiagnosticsGroup | current | The cableDiagnostics object group. | |
| 1.3.6.1.4.1.17713.11.98.28 | GroupunitIdentificationGroup | current | The unitIdentification object group. | |
| 1.3.6.1.4.1.17713.11.98.29 | GroupauthorizationControlGroup | current | The authorizationControl object group. | |
| 1.3.6.1.4.1.17713.11.98.30 | GroupdNSGroup | current | The dNS object group. | |
| 1.3.6.1.4.1.17713.11.98.96 | GroupsupplementaryGroup | current | The supplementary object group. | |
| 1.3.6.1.4.1.17713.11.98.99 | GroupnotificationsGroup | current | The notifications group. | |
| 1.3.6.1.4.1.17713.11.99 | NodeptpTraps | |||
| 1.3.6.1.4.1.17713.11.99.0 | NodeptpTrapPrefix | |||
| 1.3.6.1.4.1.17713.11.99.0.1 | NotificationchannelChangeTrap | current | The PTP radio has changed wireless channel. This has been caused by either i) mandatory radar avoidance, a DFS impulsive interference event will also be detect… | |
| 1.3.6.1.4.1.17713.11.99.0.2 | NotificationdfsImpulsiveInterferenceTrap | current | DFS impulsive interference detected event | |
| 1.3.6.1.4.1.17713.11.99.0.3 | NotificationmainPSUPortStatusTrap | current | Current status of the Main PSU Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert | |
| 1.3.6.1.4.1.17713.11.99.0.4 | NotificationmainPSUPortDisabledWarningTrap | current | The SNMP ifAdminStatus of the interface has disabled Ethernet traffic | |
| 1.3.6.1.4.1.17713.11.99.0.5 | NotificationmainPSUPortConfigurationMismatchTrap | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch | |
| 1.3.6.1.4.1.17713.11.99.0.6 | NotificationauxPortStatusTrap | current | Current status of the Aux Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert | |
| 1.3.6.1.4.1.17713.11.99.0.7 | NotificationauxPortDisabledWarningTrap | current | The SNMP ifAdminStatus of the interface has disabled Ethernet traffic | |
| 1.3.6.1.4.1.17713.11.99.0.8 | NotificationregulatoryBandTrap | current | The Regulatory Band prohibits the wireless unit from operating outside the regulated limits. An invalid Regulatory Band may be caused by a missing or incorrect… | |
| 1.3.6.1.4.1.17713.11.99.0.9 | NotificationinstallStatusTrap | current | A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because un… | |
| 1.3.6.1.4.1.17713.11.99.0.10 | NotificationinstallArmStateTrap | current | Indicates if the unit is being installed. NB: a change of state may generate an SNMP trap and/or SMTP email alert | |
| 1.3.6.1.4.1.17713.11.99.0.11 | NotificationunitOutOfCalibrationTrap | current | The unit is out of calibration | |
| 1.3.6.1.4.1.17713.11.99.0.12 | NotificationauxPortPowerOverEthernetOutputStatusTrap | current | Current status of the Power Over Ethernet (PoE) output of the Aux port | |
| 1.3.6.1.4.1.17713.11.99.0.14 | NotificationincompatibleRegulatoryBandsTrap | current | The master and slave units have incompatible regulatory bands. NB: Both units must have compatible license keys | |
| 1.3.6.1.4.1.17713.11.99.0.15 | NotificationnoWirelessChannelAvailableTrap | current | Spectrum Management was unable to locate a suitable wireless channel to operate on | |
| 1.3.6.1.4.1.17713.11.99.0.16 | NotificationwirelessLinkDisabledWarningTrap | current | The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic | |
| 1.3.6.1.4.1.17713.11.99.0.17 | NotificationauxPortConfigurationMismatchTrap | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. Th… | |
| 1.3.6.1.4.1.17713.11.99.0.18 | NotificationsFPErrorTrap | current | If the SFP link is not OK, there are five possible causes: Either a SFP has been installed but the license key does not include SFP fiber support, a fiber link… | |
| 1.3.6.1.4.1.17713.11.99.0.19 | NotificationsFPPortStatusTrap | current | Current status of the SFP Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert | |
| 1.3.6.1.4.1.17713.11.99.0.20 | NotificationincompatibleMasterAndSlaveTrap | current | A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions, or have different TDD… | |
| 1.3.6.1.4.1.17713.11.99.0.21 | NotificationsNTPSyncTrap | current | If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP | |
| 1.3.6.1.4.1.17713.11.99.0.22 | NotificationtDDSynchronizationAlarmTrap | current | Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this lin… | |
| 1.3.6.1.4.1.17713.11.99.0.23 | NotificationsFPPortDisabledWarningTrap | current | The SNMP ifAdminStatus of the interface has disabled Ethernet traffic | |
| 1.3.6.1.4.1.17713.11.99.0.24 | NotificationsFPPortConfigurationMismatchTrap | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. Th… | |
| 1.3.6.1.4.1.17713.11.99.0.25 | NotificationlinkModeOptimizationMismatchTrap | current | The remote node of this link has been configured with a different link mode optimization | |
| 1.3.6.1.4.1.17713.11.99.0.26 | NotificationtDMInterfaceStatusTrap | current | @Current status of the connection to the TDM Box. A state of 'Up' on a green background indicates that the TDM Box is connected OK. When connecting a TDM Box o… | |
| 1.3.6.1.4.1.17713.11.99.0.27 | NotificationtDMChannelStatusTrap | current | Current status of the TDM channels. A value of 0 indicates that a TDM channel is established | |
| 1.3.6.1.4.1.17713.11.99.0.28 | NotificationtDMChannelLoopbackTrap | current | The loopback status of TDM channels. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit… | |
| 1.3.6.1.4.1.17713.11.99.0.29 | NotificationnIDULanPortStatusTrap | current | Current status of the NIDU LAN Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert | |
| 1.3.6.1.4.1.17713.11.99.0.30 | NotificationsyslogStateTrap | current | The syslog service has been enabled or disabled | |
| 1.3.6.1.4.1.17713.11.99.0.31 | NotificationsyslogLocalNearlyFullTrap | current | The syslog local log is nearly full (90%) | |
| 1.3.6.1.4.1.17713.11.99.0.32 | NotificationsyslogLocalWrappedTrap | current | The syslog local log has wrapped | |
| 1.3.6.1.4.1.17713.11.99.0.33 | NotificationsyslogClientTrap | current | Enable or disable the syslog client | |
| 1.3.6.1.4.1.17713.11.99.0.34 | NotificationsecureModeAlarmTrap | current | The secure mode (e.g. FIPS, UC-APL) state of the unit. The secure mode is not configured(1) state indicates that the unit is capable of secure mode operation, … | |
| 1.3.6.1.4.1.17713.11.99.0.35 | NotificationdataBridgingStatusAlarmTrap | current | Ethernet Data traffic bridging is disabled because the wireless link is not operating at the configured Lowest Data Modulation Mode | |
| 1.3.6.1.4.1.17713.11.99.0.36 | NotificationlicenseRemainingTrialPeriodAlarmTrap | current | If the full capability trial license period is about to expire then purchase a license upgrade from your reseller. | |
| 1.3.6.1.4.1.17713.11.99.0.37 | NotificationcapacityVariantMismatchTrap | current | The remote node of this link has a lower link capacity. Operating with a reduced effective link capacity. | |
| 1.3.6.1.4.1.17713.11.99.0.38 | NotificationmaxLinkRangeExceededTrap | current | The measured link range is greater than the maximum allowed by the license key. The link will operate at a reduced capacity while this condition applies. This … | |
| 1.3.6.1.4.1.17713.11.99.0.39 | NotificationtDMConfigurationMismatchTrap | current | Current status of the configuration of the TDM Box. A state of 'Ok' on a green background indicates that the TDM Box configuration is matched OK with the remot… | |
| 1.3.6.1.4.1.17713.11.99.0.40 | NotificationnIDULanPortDisabledWarningTrap | current | The SNMP ifAdminStatus of the interface has disabled Ethernet traffic | |
| 1.3.6.1.4.1.17713.11.99.0.41 | NotificationnIDULanPortConfigurationMismatchTrap | current | The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch. | |
| 1.3.6.1.4.1.17713.11.99.0.44 | NotificationportAllocationMismatchTrap | current | The local and remote ODUs have different services configured. | |
| 1.3.6.1.4.1.17713.11.99.0.45 | NotificationwirelessLinkStatusAlarmTrap | current | Current status of the wireless link. A state of Up on a green background indicates that a wireless link is established | |
| 1.3.6.1.4.1.17713.11.99.0.46 | NotificationlbtDetectedTrap | current | Listen-Before-Talk (LBT) detected event | |
| 1.3.6.1.4.1.17713.11.99.0.47 | NotificationsecureLicenseSignatureAlarmTrap | current | Alarm condition indicates that the unit's license is not secure enough for FIPS approved mode. |