CAT2600-MIB
150 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises IpAddress TimeTicks |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9 | Nodecisco | |||
| 1.3.6.1.4.1.9.1 | NodecatProd | |||
| 1.3.6.1.4.1.9.1.111 | Nodecat2600 | |||
| 1.3.6.1.4.1.9.1.111.1 | Nodecat2600Ts | |||
| 1.3.6.1.4.1.9.1.111.1.1 | Nodecat2600TsObjectID | |||
| 1.3.6.1.4.1.9.1.111.1.1.1 | Nodecat2600TsSysObjectID | |||
| 1.3.6.1.4.1.9.1.111.1.2 | Nodecat2600TsObjects | |||
| 1.3.6.1.4.1.9.1.111.1.2.1 | Nodecat2600TsMain | |||
| 1.3.6.1.4.1.9.1.111.1.2.1.1 | Nodecat2600TsConfig | |||
| 1.3.6.1.4.1.9.1.111.1.2.1.1.1 | Scalarcat2600TsFwVer | read-only | mandatory | The firmware version in the form major.minor. For port microcode (SOLO) version information see the mgmt.mib-2.interfaces.ifTable.ifEntry.ifDescr object. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.2 | Scalarcat2600TsHwVer | read-only | mandatory | The hardware version in the form major.minor. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.3 | Scalarcat2600TsSerialNumber | read-only | mandatory | System serial number. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.4 | Scalarcat2600TsInstallationDate | read-write | mandatory | Firmware installation date. This date is initially set by the Network Management station. Each time the NV RAM is cleared through the console this date needs t… |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.5 | Scalarcat2600TsFwSize | read-only | mandatory | Size in bytes of the binary firmware image. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.6 | Scalarcat2600TsFwCRC | read-only | mandatory | Firmware binary image CRC value. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.7 | Scalarcat2600TsFwManufacturer | read-only | mandatory | Firmware manufacturer. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.8 | Scalarcat2600TsIpAddr | read-write | mandatory | IP address of the switch. Changes to this object take effect immediately. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.9 | Scalarcat2600TsNetMask | read-write | mandatory | IP subnet mask of the switch. Changes to this object take effect immediately. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.10 | Scalarcat2600TsDefaultGateway | read-write | mandatory | IP default gateway used by the switch. Changes to this object take effect immediately. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.14 | Tablecat2600TsTrapRcvrTable | not-accessible | mandatory | A table of managers to which to send traps. Entries in the table are saved across resets and power cycles. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.14.1 | Rowcat2600TsTrapRcvrEntry | not-accessible | mandatory | Definition of rows in the trap receiver table. The column cat2600TsTrapRcvrStatus is used to create and delete rows in the table. Creation requires a SET PDU w… |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.1 | Columncat2600TsTrapRcvrIndex | read-only | mandatory | The index of the row in the table. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.2 | Columncat2600TsTrapRcvrStatus | read-write | mandatory | Setting the value of this object to invalid(3) deletes the row from the table. The value invalid(3) should never be returned on a GET. Setting this value to cr… |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.3 | Columncat2600TsTrapRcvrIpAddress | read-write | mandatory | IP address for an SNMP manager that is to receive the trap. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.4 | Columncat2600TsTrapRcvrComm | read-write | mandatory | Community string to use. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.14.1.5 | Columncat2600TsTrapRcvrDmns | read-write | mandatory | Domains on which traps to this target are sent. Each octet within the value of this object specifies a set of eight domains, with the first octet specifying do… |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.19 | Scalarcat2600TsPingInterval | read-write | mandatory | This variable specifies the interval in seconds of sending ICMP Echo Requests to the default gateway. No PING packets will be sent if the value is set to 0. Th… |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.20 | Scalarcat2600TsTapPort | read-write | mandatory | Select the port to monitor traffic. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.21 | Scalarcat2600TsTapMonitoredPort | read-write | mandatory | Allows the selection of the port that will be monitored by the port selected by cat2600TsTapPort. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.22 | Scalarcat2600TsCrcThresholdHi | read-write | mandatory | Threshold for the switch to change to store and forward mode. A change in mode also generates a trap. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.23 | Scalarcat2600TsCrcThresholdLow | read-write | mandatory | Threshold for the switch to change to store and forward mode. A change in mode also generates a trap. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.24 | Scalarcat2600TsPortSwitchModeChangeTrapEnable | read-write | mandatory | Enable or disable the trap sent out when the switching mode changes from cut-through to store and forward. |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.25 | Scalarcat2600TsTrendThreshold | read-write | mandatory | Based on trend calculation of the Dynamic Cut State algorithm, when this value is exceeded the port changes from cut-through to store and forward mode. The def… |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.26 | Scalarcat2600TsSamplingPeriod | read-write | mandatory | Sampling period in minutes for determining if the error rate of CRC errors has been exceeded. The default value for this object is 10 minutes. The valid range … |
| 1.3.6.1.4.1.9.1.111.1.2.1.1.27 | Scalarcat2600TsNumberUFC | read-only | mandatory | The number of UFCs installed in the switch. A value of zero (or an SNMP error of NOSUCH) indicates there are NO UFCs installed in this switch. This value indic… |
| 1.3.6.1.4.1.9.1.111.1.2.1.2 | Nodecat2600TsSys | |||
| 1.3.6.1.4.1.9.1.111.1.2.1.2.1 | Scalarcat2600TsNumPorts | read-only | mandatory | The maximum number of physical ports on the switch. This value includes all base ports plus all ports on any UFC cards. It does not include internally defined … |
| 1.3.6.1.4.1.9.1.111.1.2.1.2.2 | Scalarcat2600TsNumStations | read-only | mandatory | Aggregate number of currently active stations (nodes) on all ports on the switch. |
| 1.3.6.1.4.1.9.1.111.1.2.1.2.3 | Scalarcat2600TsMostStations | read-only | mandatory | Highest aggregate number of stations ever active on all ports at one time, since the last reset or power cycle. This includes the default MAC address entries f… |
| 1.3.6.1.4.1.9.1.111.1.2.1.2.4 | Scalarcat2600TsMaxStations | read-only | mandatory | Highest aggregate number of stations which the switch can support simultaneously. |
| 1.3.6.1.4.1.9.1.111.1.2.1.2.5 | Scalarcat2600TsReset | read-write | mandatory | This object is used to reset the switch. Writing softReset(3) causes the switch to reset the hardware, run quick diagnostics, clear all counters, start switchi… |
| 1.3.6.1.4.1.9.1.111.1.2.1.2.6 | Scalarcat2600TsNumResets | read-only | mandatory | Number of soft resets the switch has executed since the last hard reset or power cycle. Soft resets are defined as writing softReset(3) to cat2600TsReset, pres… |
| 1.3.6.1.4.1.9.1.111.1.2.1.2.7 | Scalarcat2600TsAddrAgingTime | read-write | mandatory | Number of minutes of inactivity before an address entity is aged out. A value of zero means no aging. Note: if an address shows up on another port, the origina… |
| 1.3.6.1.4.1.9.1.111.1.2.1.2.11 | Scalarcat2600TsSysTemperature | read-only | mandatory | Temperature condition of the system. A change in this value generates a TRAP. |
| 1.3.6.1.4.1.9.1.111.1.2.1.2.12 | Scalarcat2600TsInstalledMemory | read-only | mandatory | Total amount of CPU memory installed (in megabytes). |
| 1.3.6.1.4.1.9.1.111.1.2.1.2.13 | Scalarcat2600TsSysCurTime | read-write | mandatory | Current time at the switch. To set the time use the format yyyy mm dd hh mm ss. All fields are required. |
| 1.3.6.1.4.1.9.1.111.1.2.2 | Nodecat2600TsPort | |||
| 1.3.6.1.4.1.9.1.111.1.2.2.1 | Tablecat2600TsPortTable | not-accessible | mandatory | A table of information about each port. The number of rows is given by cat2600TsNumPorts. (This value refers to PHYSICAL ports as opposed to internal logical C… |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1 | Rowcat2600TsPortEntry | not-accessible | mandatory | Definition of rows in the port table. The number of rows is determined by the hardware and is specified by the value of cat2600TsNumPorts. Rows can not be crea… |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.1 | Columncat2600TsPortIndex | read-only | mandatory | The ifIndex value corresponding to each port entry. For TR interfaces, the TsPortIndex corresponds to the Port Number or POE Index. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.2 | Columncat2600TsPortRcvLocalFrames | read-only | mandatory | Number of frames received where the destination is on this port. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.3 | Columncat2600TsPortForwardedFrames | read-only | mandatory | Number of frames received on this port and forwarded to another port or the system module for processing. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.4 | Columncat2600TsPortMostStations | read-only | mandatory | Highest number of stations ever active at any time since the last reset of the switch as seen by this port. This includes the default MAC address entries for t… |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.5 | Columncat2600TsPortMaxStations | read-only | mandatory | Maximum number of stations which the port can support simultaneously. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.6 | Columncat2600TsPortSWHandledFrames | read-only | mandatory | Number of Frames received on this port and delivered to the system module for processing. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.7 | Columncat2600TsPortLocalStations | read-only | mandatory | Number of stations on this port's address table which belong to the segment attached to this port. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.8 | Columncat2600TsPortRemoteStations | read-only | mandatory | Number of stations on this port's address table which belong to segments attached to other ports. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.9 | Columncat2600TsPortUnknownStaFrames | read-only | mandatory | Number of unicast frames received on this port and forwarded to the system module for processing because the source or destination station address is not in th… |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.10 | Columncat2600TsPortResetStats | read-write | mandatory | Setting this object to reset(3) causes all traffic counters for this port to be set to zero. Also the value of cat2600TsPortResetTimer is set to zero. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.11 | Columncat2600TsPortResetTimer | read-only | mandatory | Time (in 100th second ticks) since the port counters were reset. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.12 | Columncat2600TsPortResetAddrs | read-write | mandatory | Setting this object to reset(3) clears all address table entries for this port as well as setting all port traffic counters to zero and setting cat2600TsPortRe… |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.13 | Columncat2600TsPortRcvBcasts | read-only | mandatory | Number of Broadcast Frames received on this port without errors. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.14 | Columncat2600TsPortSwitchedFrames | read-only | mandatory | Number of frames switched on this port |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.15 | Columncat2600TsPortLinkState | read-only | mandatory | Link state of the port. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.16 | Columncat2600TsPortHashOverflows | read-only | mandatory | Number of times a hash bucket was full when trying to add an entry to the port address table. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.17 | Columncat2600TsPortAddrAgingTime | read-write | mandatory | Port level address aging time. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.18 | Columncat2600TsPortSwitchMode | read-write | mandatory | Operational frame switching mode for the port. When in auto mode the port uses the Direct Cut algorithm to place the port in either cut-thru or store-and- forw… |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.19 | Columncat2600TsPortFixedCfg | read-write | mandatory | Use fixed configuration or run auto detection to determine configuration. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.20 | Columncat2600TsPortMode | read-write | mandatory | When read, this object indicates the Port Mode obtained by the auto-detect function. It is a valid read object only when TsPortFixedCfg is set to auto-detect(1… |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.21 | Columncat2600TsPortDuplex | read-write | mandatory | Version 1 MIB When read, this object indicates the Port Duplex state obtained by the auto-detect function. This object is a valid read object any time that TSP… |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.22 | Columncat2600TsPortCfgLoss | read-only | mandatory | Number of events as described in TsPortCfgLossRC after the port has completed the join process and then lost communication. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.23 | Columncat2600TsPortCfgLossRC | read-only | mandatory | Reason code describing the cause of configuration loss. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.24 | Columncat2600TsPortCRCCount | read-only | mandatory | Number of frames received with CRC error. This object is equivalent to dot5StatsLineError and to the dtrMac MIB object txiStatsLineErrorCounter. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.25 | Columncat2600TsPortHPChannelFrames | read-only | mandatory | Number of frames sent to the high priority channel of the particular Token-Ring port. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.26 | Columncat2600TsPortLPChannelFrames | read-only | mandatory | Number of frames sent to the low priority channel of the particular Token-Ring port. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.27 | Columncat2600TsPortHPThreshold | read-only | mandatory | Priority level at which frames are sent to the High priority channel. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.28 | Columncat2600TsPortCfgRingSpeed | read-write | mandatory | When read this object indicates the Port Ring Speed obtained by the RSA function. Write to this object when defining the Port Ring Speed for a fixed configurat… |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.29 | Columncat2600TsPortCfgRSA | read-write | mandatory | User configured Ring Speed Adjust or fixed speed. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.30 | Columncat2600TsPortDomain | read-only | mandatory | Domain that the port belongs to. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.31 | Columncat2600TsPortCfgLossThreshold | read-write | mandatory | Number of configuration loss events (described in TsPortCfgLossRC) during the sample period which, if exceeded, should cause the port to be disabled. If the po… |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.32 | Columncat2600TsPortCfgLossSamplingPeriod | read-write | mandatory | The sampling period, in minutes, for which the port monitors to see if the configuration loss threshold has been exceeeded. |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.33 | Columncat2600TsPortBeaconStationAddress | not-accessible | mandatory | MAC address of the Station last generating a beacon MAC frame. This information is present for the generation of a trap and should not be used to represent the… |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.34 | Columncat2600TsPortBeaconNAUN | not-accessible | mandatory | MAC address of the NAUN station last generating a beacon MAC frame. This information is present for the generation of a trap and should not be used to represen… |
| 1.3.6.1.4.1.9.1.111.1.2.2.1.1.35 | Columncat2600TsPortBeaconType | not-accessible | mandatory | The type of Beacon which last occurred. Values are the same as for the Beacon Type subvector and are defined as follows: X'0001' Issued by a Dual Ring Station … |
| 1.3.6.1.4.1.9.1.111.1.2.2.2 | Tablecat2600TsOptPortStaTable | not-accessible | mandatory | A table of station addresses known at an individual port. This table is designed to reduce the number of SNMP GETNEXT requests. This is done by packing many va… |
| 1.3.6.1.4.1.9.1.111.1.2.2.2.1 | Rowcat2600TsOptPortStaEntry | not-accessible | mandatory | Definition of the rows in the optimized port station address table. Rows can not be created or deleted via SNMP requests. |
| 1.3.6.1.4.1.9.1.111.1.2.2.2.1.1 | Columncat2600TsOptPortStaPos | read-only | mandatory | Second index for items in the optimized port station address table. |
| 1.3.6.1.4.1.9.1.111.1.2.2.2.1.2 | Columncat2600TsOptPortStaVal | read-only | mandatory | An OCTET STRING containing a multiple number of stations from a port station address table. Each entry is encoded in the following format: Station MAC address … |
| 1.3.6.1.4.1.9.1.111.1.2.2.3 | Tablecat2600TsPortStnTable | not-accessible | mandatory | Port station table. |
| 1.3.6.1.4.1.9.1.111.1.2.2.3.1 | Rowcat2600TsPortStnEntry | not-accessible | mandatory | Definition of rows in the port table. The number of rows is determined by the hardware and is specified by the value of cat2600TsNumPorts. Rows can not be crea… |
| 1.3.6.1.4.1.9.1.111.1.2.2.3.1.1 | Columncat2600TsPortStnPortNum | read-only | mandatory | Port number corresponding to this entry. |
| 1.3.6.1.4.1.9.1.111.1.2.2.3.1.2 | Columncat2600TsPortStnAddress | read-only | mandatory | Station MAC address. Equivalent to ifPhysAddr for this port. |
| 1.3.6.1.4.1.9.1.111.1.2.2.3.1.3 | Columncat2600TsPortStnLocation | read-only | mandatory | Where the station is located. |
| 1.3.6.1.4.1.9.1.111.1.2.2.3.1.4 | Columncat2600TsPortStnSrcFrames | read-only | mandatory | Number of frames with this station as the source. |
| 1.3.6.1.4.1.9.1.111.1.2.2.3.1.5 | Columncat2600TsPortStnSrcBytes | read-only | mandatory | Number of Bytes with this station as the source. |
| 1.3.6.1.4.1.9.1.111.1.2.2.3.1.6 | Columncat2600TsPortStnDestnFrames | read-only | mandatory | Number of frames with this station as the destination. |
| 1.3.6.1.4.1.9.1.111.1.2.2.3.1.7 | Columncat2600TsPortStnDestnBytes | read-only | mandatory | Number of bytes with this station as the destination. |
| 1.3.6.1.4.1.9.1.111.1.2.3 | Nodecat2600TsDmns | |||
| 1.3.6.1.4.1.9.1.111.1.2.3.1 | Tablecat2600TsDmnTable | not-accessible | mandatory | Currently active domains on the switch. |
| 1.3.6.1.4.1.9.1.111.1.2.3.1.1 | Rowcat2600TsDmnEntry | not-accessible | mandatory | Definition of each row in the domain Table |
| 1.3.6.1.4.1.9.1.111.1.2.3.1.1.1 | Columncat2600TsDmnIndex | read-only | mandatory | Domain number for each row. |
| 1.3.6.1.4.1.9.1.111.1.2.3.1.1.2 | Columncat2600TsDmnPorts | read-write | mandatory | The set of ports that belong to this Domain. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1… |
| 1.3.6.1.4.1.9.1.111.1.2.3.1.1.3 | Columncat2600TsDmnIpState | read-write | mandatory | IP configuration method for this domain. |
| 1.3.6.1.4.1.9.1.111.1.2.3.1.1.4 | Columncat2600TsDmnIpAddress | read-write | mandatory | The IP Address of this Domain. Changes to this object will take effect immediately. |
| 1.3.6.1.4.1.9.1.111.1.2.3.1.1.5 | Columncat2600TsDmnIpSubnetMask | read-write | mandatory | The subnet mask for this domain. Changes to this object will take effect immediately. |
| 1.3.6.1.4.1.9.1.111.1.2.3.1.1.6 | Columncat2600TsDmnIpDefaultGateway | read-write | mandatory | The IP Address of the default gateway for this Domain. Changes to this object will take effect immediately. |
| 1.3.6.1.4.1.9.1.111.1.2.3.1.1.7 | Columncat2600TsDmnStp | read-write | mandatory | Turn Spanning tree on or off. Changes to this object will take effect immediately. The Spanning Tree Objects themselves are in the dtrConc MIB. |
| 1.3.6.1.4.1.9.1.111.1.2.3.1.1.8 | Columncat2600TsDmnName | read-write | mandatory | User assigned name for each domain. |
| 1.3.6.1.4.1.9.1.111.1.2.3.1.1.9 | Columncat2600TsDmnIfIndex | read-only | mandatory | The ifIndex of the interface entry corresponding to each configured domain. |
| 1.3.6.1.4.1.9.1.111.1.2.3.1.1.10 | Columncat2600TsDmnBaseBridgeAddr | read-only | mandatory | Base MAC address of this domain. Internally equivalent to dtrCRFMacAddress and to ifPhysAddress of the 'Domain' port. |
| 1.3.6.1.4.1.9.1.111.1.2.3.1.1.11 | Columncat2600TsDmnNumStations | read-only | mandatory | Aggregate number of currently active stations (nodes) on all ports in the domain. |
| 1.3.6.1.4.1.9.1.111.1.2.3.1.1.12 | Columncat2600TsDmnMostStations | read-only | mandatory | Highest aggregate number of stations ever active on all ports at one time, since the last reset or power cycle. |
| 1.3.6.1.4.1.9.1.111.1.2.3.5 | Tablecat2600TsDmnStationTable | not-accessible | mandatory | Stations seen in each domain. |
| 1.3.6.1.4.1.9.1.111.1.2.3.5.1 | Rowcat2600TsDmnStationEntry | not-accessible | mandatory | Definition of each row in the domain specific station table. The object is equivalent to dtrFdbDynamicAddrTable or dtrFdbStaticAddrTable depending if the entry… |
| 1.3.6.1.4.1.9.1.111.1.2.3.5.1.1 | Columncat2600TsDmnStationDmnIndex | read-only | mandatory | Integer reference to the domain number in the domain table. |
| 1.3.6.1.4.1.9.1.111.1.2.3.5.1.2 | Columncat2600TsDmnStationAddress | read-only | mandatory | The Station's MAC address. |
| 1.3.6.1.4.1.9.1.111.1.2.3.5.1.3 | Columncat2600TsDmnStationPort | read-only | mandatory | The source port for the Station. The dtrConc MIB equivalents are dtrFdbDynamicAddrPortNumber and dtrFdbStaticAddrPortNumber. |
| 1.3.6.1.4.1.9.1.111.1.2.3.5.1.4 | Columncat2600TsDmnStationTraffic | read-only | mandatory | A bit string that identifies the ports that this station has generated traffic to or from. The bits correspond to ports, with bits and ports numbered from righ… |
| 1.3.6.1.4.1.9.1.111.1.2.3.6 | Tablecat2600TsOptDmnStaTable | not-accessible | mandatory | A table of station addresses known at an individual port. This table is designed to reduce the number of SNMP GETNEXT requests. This is done by packing many va… |
| 1.3.6.1.4.1.9.1.111.1.2.3.6.1 | Rowcat2600TsOptDmnStaEntry | not-accessible | mandatory | Definition of the rows in the optimized domain station address table. Rows can not be created or deleted via SNMP requests. |
| 1.3.6.1.4.1.9.1.111.1.2.3.6.1.1 | Columncat2600TsOptDmnStaPos | read-only | mandatory | Second index for items in the optimized port station address table. |
| 1.3.6.1.4.1.9.1.111.1.2.3.6.1.2 | Columncat2600TsOptDmnStaVal | read-only | mandatory | An OCTET STRING containing a multiple number of stations from the domain station address table. Each entry is encoded in the following format: Station MAC addr… |
| 1.3.6.1.4.1.9.1.111.1.2.4 | Nodecat2600TsPipe | |||
| 1.3.6.1.4.1.9.1.111.1.2.4.1 | Tablecat2600TsPipeTable | not-accessible | mandatory | The TokenPipe table. |
| 1.3.6.1.4.1.9.1.111.1.2.4.1.1 | Rowcat2600TsPipeEntry | not-accessible | mandatory | Definition of each row in the TokenPipe table. |
| 1.3.6.1.4.1.9.1.111.1.2.4.1.1.1 | Columncat2600TsPipeNumber | read-only | mandatory | The TokenPipe number for this row. |
| 1.3.6.1.4.1.9.1.111.1.2.4.1.1.2 | Columncat2600TsPipePorts | read-write | mandatory | The set of ports in this switch which are active in this Pipe. Each octet within the value of this object specifies a set of eight ports, with the first octet … |
| 1.3.6.1.4.1.9.1.111.1.2.5 | Nodecat2600TsFilter | |||
| 1.3.6.1.4.1.9.1.111.1.2.5.1 | Tablecat2600TsFilterTable | not-accessible | mandatory | Filters set up in the switch. |
| 1.3.6.1.4.1.9.1.111.1.2.5.1.1 | Rowcat2600TsFilterEntry | not-accessible | mandatory | Definition of each row in the filter table. |
| 1.3.6.1.4.1.9.1.111.1.2.5.1.1.1 | Columncat2600TsFilterStationAddress | read-only | mandatory | The MAC address in a frame to which this entry's filtering information applies. |
| 1.3.6.1.4.1.9.1.111.1.2.5.1.1.2 | Columncat2600TsFilterType | read-only | mandatory | There are two types of filters (i) source filters which act on the source address portion of a packet and (ii) destination filters which act on the destination… |
| 1.3.6.1.4.1.9.1.111.1.2.5.1.1.3 | Columncat2600TsFilterStatus | read-write | mandatory | This object indicates the status of this entry. valid(1) - this entry is currently in use and will remain so after the next reset of the bridge. invalid(2) - w… |
| 1.3.6.1.4.1.9.1.111.1.2.5.1.1.4 | Columncat2600TsFilterPorts | read-write | mandatory | The set of ports to which this filter is applied. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying po… |
| 1.3.6.1.4.1.9.1.111.1.2.5.1.1.5 | Columncat2600TsFilterMask | read-write | mandatory | The filter mask for this station. The semantics of the filter mask depend on the type of filter. For a source filter, the mask gives the ports that are allowed… |
| 1.3.6.1.4.1.9.1.111.1.2.6 | Nodecat2600TsUFC | |||
| 1.3.6.1.4.1.9.1.111.1.2.6.1 | Tablecat2600TsUFCTable | not-accessible | mandatory | A table of the installed UFC cards in the switch. The number of entries in the table is given by cat2600TsNumberofUFCs. |
| 1.3.6.1.4.1.9.1.111.1.2.6.1.1 | Rowcat2600TsUFCEntry | not-accessible | mandatory | The objects contained in the UFC table. |
| 1.3.6.1.4.1.9.1.111.1.2.6.1.1.1 | Columncat2600TsUFCSlotNum | read-only | mandatory | The number of the slot in which the UFC is installed. |
| 1.3.6.1.4.1.9.1.111.1.2.6.1.1.2 | Columncat2600TsUFCNumPhysIfs | read-only | mandatory | The total number of physical network interfaces on the UFC. This count does not include the interface _OF_ the card or any logical interfaces which be _ON_ the… |
| 1.3.6.1.4.1.9.1.111.1.2.6.1.1.3 | Columncat2600TsUFCManufacturer | read-only | mandatory | Firmware manufacturer. |
| 1.3.6.1.4.1.9.1.111.1.2.6.1.1.4 | Columncat2600TsUFCType | read-only | mandatory | The code representing what type of UFC is present. UFC codes are assigned by Cisco. |
| 1.3.6.1.4.1.9.1.111.1.2.6.1.1.5 | Columncat2600TsUFCTypeDesc | read-only | mandatory | A text string describing what type of UFC is present. |
| 1.3.6.1.4.1.9.1.111.1.2.6.1.1.6 | Columncat2600TsUFCHwVer | read-only | mandatory | The hardware version in the form major.minor. |
| 1.3.6.1.4.1.9.1.111.1.2.6.1.1.7 | Columncat2600TsUFCFwVer | read-only | mandatory | The firmware version in the form major.minor. |
| 1.3.6.1.4.1.9.1.111.1.2.6.1.1.8 | Columncat2600TsUFCStatus | read-only | mandatory | The operational status of the UFC. |
| 1.3.6.1.4.1.9.1.111.1.2.6.1.1.9 | Columncat2600TsUFCReset | read-write | mandatory | The object is used to reset a UFC. Writing a softReset(3) causes the switch to reset the hardware, run the minimum number of diagnostics, and clear all counter… |
| 1.3.6.1.4.1.9.1.111.1.3 | NodedtrMIBs | |||
| 1.3.6.1.4.1.9.1.111.1.3.1 | NodedtrConcMIB | |||
| 1.3.6.1.4.1.9.1.111.1.3.2 | NodedtrMacMIB |