CISCO-ATM-IF-MIB
76 objects
A MIB module for an ATM interface configuration.
Imported Objects
| ATM-MIB | atmInterfaceConfEntry |
| CISCO-SMI | ciscoExperiment |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | -- RFC 1695 TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.10.14 | IdentityciscoAtmIfMIB | A MIB module for an ATM interface configuration. | ||
| 1.3.6.1.4.1.9.10.14.0 | NodeciscoAtmIfMIBNotifications | |||
| 1.3.6.1.4.1.9.10.14.0.1 | NotificationciscoAtmIfEvent | current | This notification is generated when ever ILMI or SSCOP FSM state changes | |
| 1.3.6.1.4.1.9.10.14.1 | NodeciscoAtmIfMIBObjects | |||
| 1.3.6.1.4.1.9.10.14.1.1 | TableciscoAtmIfTable | not-accessible | current | This table contains ATM local interface configuration parameters, one entry per ATM interface port. |
| 1.3.6.1.4.1.9.10.14.1.1.1 | RowciscoAtmIfEntry | not-accessible | current | This list conatins additonal ATM interface configuration parameters and state variables. |
| 1.3.6.1.4.1.9.10.14.1.1.1.1 | ColumnciscoAtmIfType | read-write | current | The type of ATM interface which is either a UNI (User to Network), PNNI, IISP or NNI PVC only. To modify the ciscoAtmIftype, ifAdminStatus has to be down and a… |
| 1.3.6.1.4.1.9.10.14.1.1.1.2 | ColumnciscoAtmIfSide | read-write | current | The side of ATM interface which is either a user or network side.NotApplicable value implies that ciscoAtmIftype is other than uni or iisp. |
| 1.3.6.1.4.1.9.10.14.1.1.1.3 | ColumnciscoAtmIfUniType | read-write | current | The type of User to Network interface is either private or public. If ciscoAtmIfType is not uni then ciscoAtmIfUniType value should be ignored. |
| 1.3.6.1.4.1.9.10.14.1.1.1.4 | ColumnciscoAtmIfPVPs | read-only | current | The number of permanent virtual paths at this interface. |
| 1.3.6.1.4.1.9.10.14.1.1.1.5 | ColumnciscoAtmIfPVCs | read-only | current | The number of permanent virtual channels at this interface. |
| 1.3.6.1.4.1.9.10.14.1.1.1.6 | ColumnciscoAtmIfActiveSVPs | read-only | current | The number of active switched virtual paths at this interface. |
| 1.3.6.1.4.1.9.10.14.1.1.1.7 | ColumnciscoAtmIfActiveSVCs | read-only | current | The number of active switched virtual channels at this interface. |
| 1.3.6.1.4.1.9.10.14.1.1.1.8 | ColumnciscoAtmIfTotalConnections | read-only | current | The total number of existing connections at this interface. |
| 1.3.6.1.4.1.9.10.14.1.1.1.9 | ColumnciscoAtmIfConfVplIf | read-only | current | The number of configured VP interfaces at this physical interface. |
| 1.3.6.1.4.1.9.10.14.1.1.1.10 | ColumnciscoAtmIfPortType | read-only | current | The type of physical layer medium on the port. |
| 1.3.6.1.4.1.9.10.14.1.1.1.11 | ColumnciscoAtmIfXmitLed | read-only | current | The transmit LED color of this port. |
| 1.3.6.1.4.1.9.10.14.1.1.1.12 | ColumnciscoAtmIfRecvLed | read-only | current | The receive LED color of this port. |
| 1.3.6.1.4.1.9.10.14.1.1.1.13 | ColumnciscoAtmIfXmitCells | read-only | current | The number of cells transmitted of this interface, including p2p and p2mp cells. |
| 1.3.6.1.4.1.9.10.14.1.1.1.14 | ColumnciscoAtmIfRecvCells | read-only | current | The number of cells received of this interface, including p2p and p2mp cells. |
| 1.3.6.1.4.1.9.10.14.1.1.1.15 | ColumnciscoAtmIfSvcMinVci | read-only | deprecated | The minimum of the range of values from which VCI's are assigned to new SVC connections. By this value being larger, more VCI's are reserved for setting up PVC… |
| 1.3.6.1.4.1.9.10.14.1.1.1.16 | ColumnciscoAtmIfIlmiConfiguration | read-write | current | Enable/Disable ILMI configuration on this interface. The configuration takes effect only on the next interface restart. Disabling this object will also disable… |
| 1.3.6.1.4.1.9.10.14.1.1.1.17 | ColumnciscoAtmIfIlmiAddressRegistration | read-write | current | Enable/Disable ILMI Address Registration on on this interface. The configuration takes effect only on the next interface restart. |
| 1.3.6.1.4.1.9.10.14.1.1.1.18 | ColumnciscoAtmIfIlmiAutoConfiguration | read-write | current | Enable/Disable ILMI link and interface type determination. The configuration takes effect only on the next interface restart. |
| 1.3.6.1.4.1.9.10.14.1.1.1.19 | ColumnciscoAtmIfIlmiKeepAlive | read-write | current | The amount of time that should elapse between successive ILMI keepalive messages sent on this interface. A value of 0 disables ILMI keepalive messages on this … |
| 1.3.6.1.4.1.9.10.14.1.1.1.20 | ColumnciscoAtmIfSoftVcDestAddress | read-only | current | The 20 byte ATM address of the destination ATM interface for soft ATM PVC/PVP |
| 1.3.6.1.4.1.9.10.14.1.1.1.21 | ColumnciscoAtmIfUniSignallingVersion | read-write | current | The version of UNI signalling that is currently being used on the interface. The appropriate value, either atmfUni3Dot0, atmfUni3Dot1 or atmfUni4Dot0, is used … |
| 1.3.6.1.4.1.9.10.14.1.1.1.22 | ColumnciscoAtmIfSvcUpcIntent | read-write | deprecated | Determines the policing (Usage Parameter Control or UPC) action to take for SVCs established through this interface. Values other than passing are allowed only… |
| 1.3.6.1.4.1.9.10.14.1.1.1.23 | ColumnciscoAtmIfAddressType | read-write | obsolete | An indication of the type of the ATM addresses on this interface. To configure a new atm address, set ciscoAtmIfAddress to the address, then set this object to… |
| 1.3.6.1.4.1.9.10.14.1.1.1.24 | ColumnciscoAtmIfAddress | read-write | obsolete | The ATM address of this interface, which can be either nsap, esi or e164. For the switch, the nsap/esi address can only exist on the cpu port. |
| 1.3.6.1.4.1.9.10.14.1.1.1.31 | ColumnciscoAtmIfWellKnownVcMode | read-write | current | Indicates whether well-known VCs should be automatically or manually created for the interface. In automatic(1) mode, well-known VCs will be created with defau… |
| 1.3.6.1.4.1.9.10.14.1.1.1.32 | ColumnciscoAtmIfSignallingAdminStatus | read-write | current | Enable/Disable signalling/sscop on this interface.The disabled(2) action causes all the active SVCs on this interface to be cleared. |
| 1.3.6.1.4.1.9.10.14.1.1.1.33 | ColumnciscoAtmIfCdLed | read-only | current | The Cd LED color of this port. |
| 1.3.6.1.4.1.9.10.14.1.1.1.34 | ColumnciscoAtmIfIlmiAccessFilter | read-write | current | The access filter which allows or denies certain ILMI registered addresses on this interface when ciscoAtmIfIlmiAddressRegistration is set to enable(1). permit… |
| 1.3.6.1.4.1.9.10.14.1.1.1.35 | ColumnciscoAtmIfConfigAESA | read-write | current | The ATM End System Address (AESA) of this interface can be configured by entering the full 20 octet AESA, or the 6 octet ESI and 1 octet Selector Byte. If the … |
| 1.3.6.1.4.1.9.10.14.1.1.1.36 | ColumnciscoAtmIfDerivedAESA | read-only | current | The ATM End System Address (AESA) of this interface. The AESA is configured using ciscoAtmIfConfigAESA or can be automatically generated. A length of zero indi… |
| 1.3.6.1.4.1.9.10.14.1.1.1.37 | ColumnciscoAtmIfE164Address | read-write | current | The ATM E164 address of this interface. When a native E.164 number is configured for this inteface, only native E.164 numbers are transmitted/received as the c… |
| 1.3.6.1.4.1.9.10.14.1.1.1.38 | ColumnciscoAtmIfE164AutoConversionOnly | read-write | current | Enable/Disable E164 auto conversion only on this interface. The E164 auto-conversion allows for algorithmic translation between the native E164 number and E164… |
| 1.3.6.1.4.1.9.10.14.1.1.1.39 | ColumnciscoAtmIfRxCellUpcViolations | read-only | current | The total number of nonconforming cells detected by Usage Parameter Control (UPC) for cells received on this interface. This object is not instantiated on syst… |
| 1.3.6.1.4.1.9.10.14.1.1.1.40 | ColumnciscoAtmIfRxCellDiscards | read-only | current | The total number of cells that were discarded within the switch. The cells can be discarded due to non conformance detected by Usage Parameter Control (UPC) or… |
| 1.3.6.1.4.1.9.10.14.1.1.1.41 | ColumnciscoAtmIfIlmiFSMState | read-only | current | |
| 1.3.6.1.4.1.9.10.14.1.1.1.42 | ColumnciscoAtmIfIlmiUpDownChanges | read-only | current | The number of times ILMI enters and leaves the state of upAndNormal. |
| 1.3.6.1.4.1.9.10.14.1.1.1.43 | ColumnciscoAtmIfSscopFSMState | read-only | current | The SSCOP state for an ATM interface as defined by the ITU-T. The state is idle when the interface is down or SSCOP is not enabled on the ATM interface |
| 1.3.6.1.4.1.9.10.14.1.1.1.44 | ColumnciscoAtmIfSscopUpDownChanges | read-only | current | The number of times SSCOP enters and leaves the state of DataTransferReady. |
| 1.3.6.1.4.1.9.10.14.1.1.1.45 | ColumnciscoAtmIfSvcUpcIntentCbr | read-write | current | Determines the policing (Usage Parameter Control or UPC) action to take for Constant Bit Rate SVCs established through this interface. Values other than passin… |
| 1.3.6.1.4.1.9.10.14.1.1.1.46 | ColumnciscoAtmIfSvcUpcIntentVbrRt | read-write | current | Determines the policing (Usage Parameter Control or UPC) action to take for Variable Bit Rate - Real Time SVCs established through this interface. Values other… |
| 1.3.6.1.4.1.9.10.14.1.1.1.47 | ColumnciscoAtmIfSvcUpcIntentVbrNrt | read-write | current | Determines the policing (Usage Parameter Control or UPC) action to take for Variable Bit Rate - Non Real Time SVCs established through this interface. Values o… |
| 1.3.6.1.4.1.9.10.14.1.1.1.48 | ColumnciscoAtmIfSvcUpcIntentAbr | read-write | current | Determines the policing (Usage Parameter Control or UPC) action to take for Available Bit Rate SVCs established through this interface. Values other than passi… |
| 1.3.6.1.4.1.9.10.14.1.1.1.49 | ColumnciscoAtmIfSvcUpcIntentUbr | read-write | current | Determines the policing (Usage Parameter Control or UPC) action to take for Unspecified Bit Rate SVCs established through this interface. Values other than pas… |
| 1.3.6.1.4.1.9.10.14.1.2 | ScalarciscoAtmIfIlmiAccessGlobalDefaultFilter | read-write | current | The global default access filter which set the per-switch default access filter for ILMI address registration on all interfaces. permitAll - This permits all I… |
| 1.3.6.1.4.1.9.10.14.1.3 | ScalarciscoAtmIfNotifsEnabled | read-write | current | Allows enabling/disabling of notifications for ATM Interface events |
| 1.3.6.1.4.1.9.10.14.3 | NodeciscoAtmIfMIBConformance | |||
| 1.3.6.1.4.1.9.10.14.3.1 | NodeciscoAtmIfMIBCompliances | |||
| 1.3.6.1.4.1.9.10.14.3.1.1 | ComplianceciscoAtmIfMIBCompliance | obsolete | The compliance statement for the Cisco ATM interface group. | |
| 1.3.6.1.4.1.9.10.14.3.1.2 | ComplianceciscoAtmIfMIBCompliance2 | obsolete | The compliance statement for the Cisco ATM interface group. | |
| 1.3.6.1.4.1.9.10.14.3.1.3 | ComplianceciscoAtmIfMIBCompliance3 | obsolete | The compliance statement for the Cisco ATM interface group. | |
| 1.3.6.1.4.1.9.10.14.3.1.4 | ComplianceciscoAtmIfMIBCompliance4 | obsolete | The compliance statement for the Cisco ATM interface group. | |
| 1.3.6.1.4.1.9.10.14.3.1.5 | ComplianceciscoAtmIfMIBCompliance5 | obsolete | The compliance statement for the Cisco ATM interface group. | |
| 1.3.6.1.4.1.9.10.14.3.1.6 | ComplianceciscoAtmIfMIBCompliance6 | obsolete | The compliance statement for the Cisco ATM interface group. | |
| 1.3.6.1.4.1.9.10.14.3.1.7 | ComplianceciscoAtmIfMIBCompliance7 | deprecated | The compliance statement for the Cisco ATM interface group. | |
| 1.3.6.1.4.1.9.10.14.3.1.8 | ComplianceciscoAtmIfMIBCompliance8 | current | The compliance statement for the Cisco ATM interface group. | |
| 1.3.6.1.4.1.9.10.14.3.2 | NodeciscoAtmIfMIBGroups | |||
| 1.3.6.1.4.1.9.10.14.3.2.1 | GroupciscoAtmIfMIBGroup | deprecated | A collection of objects providing the information about ATM interface related information also an ability to configure certain parameters of ATM interface. | |
| 1.3.6.1.4.1.9.10.14.3.2.2 | GroupciscoAtmIfMIBGroup2 | deprecated | Additional collection of objects providing ATM interface related information. | |
| 1.3.6.1.4.1.9.10.14.3.2.3 | GroupciscoAtmIfMIBGroup3 | obsolete | Additional collection of objects providing ATM interface related information. | |
| 1.3.6.1.4.1.9.10.14.3.2.4 | GroupciscoAtmIfMIBGroup4 | current | Additional collection of objects providing ATM switch and interface related information on Access Filter for ILMI Address Registration. | |
| 1.3.6.1.4.1.9.10.14.3.2.5 | GroupciscoAtmIfMIBGroup5 | current | Additional collection of objects providing ATM switch and interface related information for ATM Addresses. | |
| 1.3.6.1.4.1.9.10.14.3.2.6 | GroupciscoAtmIfMIBGroup6 | current | Additional collection of objects providing ATM interface related information. | |
| 1.3.6.1.4.1.9.10.14.3.2.7 | GroupciscoAtmIfMIBGroup7 | current | Additional collection of objects providing ATM switch interface Resource Manager, ILMI and Signalling related information. | |
| 1.3.6.1.4.1.9.10.14.3.2.8 | GroupciscoAtmIfMIBGroup8 | current | Additional collection of objects providing ATM interface related information. | |
| 1.3.6.1.4.1.9.10.14.3.2.9 | GroupciscoAtmIfMIBGroup9 | current | A collection of objects providing the information about ATM interface related information also an ability to configure certain parameters of ATM interface. | |
| 1.3.6.1.4.1.9.10.14.3.2.10 | GroupciscoAtmIfMIBGroup10 | current | Additional objects providing means to enable/disable notifications related to the interface ILMI and SSCOP state | |
| 1.3.6.1.4.1.9.10.14.3.2.11 | GroupciscoAtmIfNotifyGroup | current | Interface ILMI and SSCOP FSM notifications |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AtmAddr | OCTET STRING (SIZE(0|8|13|20)) | current | The ATM address used by the network entity. The address types are: no address (0 octets), E.164 (8 octets), network prefix (13 octets), and NSAP (20 octets). Note: The E.164 address is encoded in BCD format. |
| NsapAtmAddr | OCTET STRING (SIZE(20)) | current | The ATM address used by the network entity. The address types are NSAP (20 octets). |
| UpcMethod | INTEGER { passing(1), tagging(2), dropping(3) } | current | A textual convention defining options for Usage Parameter Control: passing : take no action on cells considered to violate the traffic contract. tagging : set the CLP bit in the header of cells considered to violate the… |