CISCO-ATM-QOS-MIB
70 objects
The MIB is created to provide ATM QoS information in these areas: 1. Traffic shaping on a per-VC basis 2. Traffic shaping on a per-VP basis 3. Per-VC queuing/buffering Although the initial requirements of the MIB are driven to support the GSR TAZ line card, CISCO-ATM-QOS-MIB is designed as a generic MIB to support ATM interfaces across all platforms. Here are the tables defined in this MIB: ciscoAtmQosVccTable - to provide information on traffic shaping on a per-VC basis. ciscoAtmQosVpcTable - to provide information on traffic shaping on a per-VP basis. ciscoAtmQosVcQueuingTable ciscoAtmQosVcQueuingClassTable - to provide information on per-VC queuing/buffering.
Imported Objects
| ATM-FORUM-TC-MIB | AtmServiceCategory |
| ATM-MIB | atmVclVci atmVclVpi atmVplVpi |
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.279 | IdentityciscoAtmQosMIB | The MIB is created to provide ATM QoS information in these areas: 1. Traffic shaping on a per-VC basis 2. Traffic shaping on a per-VP basis 3. Per-VC queuing/b… | ||
| 1.3.6.1.4.1.9.9.279.0 | NodeciscoAtmQosMIBNotifs | |||
| 1.3.6.1.4.1.9.9.279.1 | NodeciscoAtmQosMIBObjects | |||
| 1.3.6.1.4.1.9.9.279.1.1 | NodecaqVccParams | |||
| 1.3.6.1.4.1.9.9.279.1.1.1 | TablecaqVccParamsTable | not-accessible | current | This table is defined to provide QoS information for each active ATM VC existing on the interface. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1 | RowcaqVccParamsEntry | not-accessible | current | This list contains the ATM QoS parameters provided by ciscoAtmQosVccEntry. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.1 | ColumncaqVccParamsType | read-write | current | The service category of this virtual circuit connection. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.2 | ColumncaqVccParamsPcrIn0 | read-write | current | Input Peak Cell Rate (PCR) in kbps with Cell Loss Priority bit set to 0 (clp0). |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.3 | ColumncaqVccParamsPcrIn01 | read-write | current | Number of OAM F5 end to end loopback cells sent through the VCC. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.4 | ColumncaqVccParamsPcrOut0 | read-write | current | Output Peak Cell Rate (PCR) in kbps with Cell Loss Priority bit set to 0 (clp0). |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.5 | ColumncaqVccParamsPcrOut01 | read-write | current | Output Peak Cell Rate (PCR) in kbps with Cell Loss Priority bit set to 1 (clp01). |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.6 | ColumncaqVccParamsScrIn0 | read-write | current | Input Sustained Cell Rate (SCR) in kbps for connection with VBR type of QoS and Cell Loss Priority bit set to 0 (clp0). |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.7 | ColumncaqVccParamsScrIn01 | read-write | current | Input Sustained Cell Rate (SCR) in kbps for connection with VBR type of QoS and Cell Loss Priority bit set to 1 (clp01). |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.8 | ColumncaqVccParamsScrOut0 | read-write | current | Output Sustained Cell Rate (SCR) in kbps for connection with VBR type of QoS and Cell Loss Priority bit set to 0 (clp0). |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.9 | ColumncaqVccParamsScrOut01 | read-write | current | Output Sustained Cell Rate (SCR) in kbps for connection with VBR type of QoS and Cell Loss Priority bit set to 1 (clp01). |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.10 | ColumncaqVccParamsBcsIn0 | read-write | current | Input Burst Cell Size (BCS) for connection with VBR type of QoS and Cell Loss Priority bit set to 0 (clp0). |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.11 | ColumncaqVccParamsBcsIn01 | read-write | current | Input Burst Cell Size (BCS) for connection with VBR type of QoS and Cell Loss Priority bit set to 1 (clp01). |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.12 | ColumncaqVccParamsBcsOut0 | read-write | current | Output Burst Cell Size (BCS) for connection with VBR type of QoS and Cell Loss Priority bit set to 0 (clp0). |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.13 | ColumncaqVccParamsBcsOut01 | read-write | current | Output Burst Cell Size (BCS) for connection with VBR type of QoS and Cell Loss Priority bit set to 1 (clp01). |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.14 | ColumncaqVccParamsInheritLevel | read-only | current | The source of configuration for peak cell rate. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.15 | ColumncaqVccParamsMcrIn | read-write | current | Input Minimum Cell Rate (MCR) in kbps for connection with VBR-nrt or ABR type of QoS. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.16 | ColumncaqVccParamsMcrOut | read-write | current | Output Minimum Cell Rate (MCR) in kbps for connection with VBR-nrt or ABR type of QoS. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.17 | ColumncaqVccParamsInvRdf | read-write | current | Inverse of rate decrease factor. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.18 | ColumncaqVccParamsInvRif | read-write | current | Inverse of rate increase factor. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.19 | ColumncaqVccParamsRfl | read-only | current | The source of configuration for rate factor. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.20 | ColumncaqVccParamsCdv | read-only | current | Cell delay variation. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.21 | ColumncaqVccParamsCdvt | read-write | current | Cell delay variation tolerance. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.22 | ColumncaqVccParamsIcr | read-write | current | Initial cell rate. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.23 | ColumncaqVccParamsTbe | read-write | current | Transient buffer exposure. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.24 | ColumncaqVccParamsFrtt | read-write | current | Fixed round-trip time. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.25 | ColumncaqVccParamsNrm | read-write | current | Maximum number of tx cells for each forward rm cell. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.26 | ColumncaqVccParamsInvTrm | read-write | current | Maximum time between forward rm cells. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.27 | ColumncaqVccParamsInvCdf | read-write | current | Inverse of cutoff decrease factor. |
| 1.3.6.1.4.1.9.9.279.1.1.1.1.28 | ColumncaqVccParamsAdtf | read-write | current | Allowed cell rate decrease time factor. |
| 1.3.6.1.4.1.9.9.279.1.2 | NodecaqVpcParams | |||
| 1.3.6.1.4.1.9.9.279.1.2.1 | TablecaqVpcParamsTable | not-accessible | current | This table is defined to provide QoS information for each active ATM VP existing on the interface. |
| 1.3.6.1.4.1.9.9.279.1.2.1.1 | RowcaqVpcParamsEntry | not-accessible | current | This list contains the ATM QoS parameters provided by ciscoAtmQosVpcEntry. |
| 1.3.6.1.4.1.9.9.279.1.2.1.1.1 | ColumncaqVpcParamsVpState | read-only | current | VP state of the current permanent virtual path. |
| 1.3.6.1.4.1.9.9.279.1.2.1.1.2 | ColumncaqVpcParamsPeakRate | read-only | current | Maximum rate in kbps at which the associated permanent virtual path can transmit data. |
| 1.3.6.1.4.1.9.9.279.1.2.1.1.3 | ColumncaqVpcParamsCesRate | read-only | current | Maximum rate in kbps at which CES VCs can transmit data with the associated permanent virtual path. |
| 1.3.6.1.4.1.9.9.279.1.2.1.1.4 | ColumncaqVpcParamsDataVcCount | read-only | current | Number of data VCs currently associated with the permanent virtual path. |
| 1.3.6.1.4.1.9.9.279.1.2.1.1.5 | ColumncaqVpcParamsCesVcCount | read-only | current | Number of CES VCs currently associated with the permanent virtual path. |
| 1.3.6.1.4.1.9.9.279.1.2.1.1.6 | ColumncaqVpcParamsVcdF4Seg | read-only | current | Vcd for F4 OAM segment processing. |
| 1.3.6.1.4.1.9.9.279.1.2.1.1.7 | ColumncaqVpcParamsVcdF4Ete | read-only | current | Vcd for F4 OAM end to end processing. |
| 1.3.6.1.4.1.9.9.279.1.2.1.1.8 | ColumncaqVpcParamsScr | read-only | current | Sustained cell rate associated with the PVP. |
| 1.3.6.1.4.1.9.9.279.1.2.1.1.9 | ColumncaqVpcParamsMbs | read-only | current | Maximum burst size associated with the PVP. |
| 1.3.6.1.4.1.9.9.279.1.2.1.1.10 | ColumncaqVpcParamsAvailBw | read-only | current | Bandwidth in Kbps currently currently available on this PVP. |
| 1.3.6.1.4.1.9.9.279.1.3 | NodecaqQueuingParams | |||
| 1.3.6.1.4.1.9.9.279.1.3.1 | TablecaqQueuingParamsTable | not-accessible | current | This table provides queuing related information for a VC existing on an ATM interface. |
| 1.3.6.1.4.1.9.9.279.1.3.1.1 | RowcaqQueuingParamsEntry | not-accessible | current | This is defined as an entry in caqQueuingParamsTable. |
| 1.3.6.1.4.1.9.9.279.1.3.1.1.1 | ColumncaqQueuingParamsMeanQDepth | read-only | current | Mean Queue Depth associated with the vc. This value is calculated based on the actual queue depth on the interface and the exponential weighting constant. |
| 1.3.6.1.4.1.9.9.279.1.3.2 | TablecaqQueuingParamsClassTable | not-accessible | current | This table provides queuing information for all queuing classes associating with a VC. |
| 1.3.6.1.4.1.9.9.279.1.3.2.1 | RowcaqQueuingParamsClassEntry | not-accessible | current | This is defined as an entry in ciscoAtmQosVcQueuingClassTable to provide queuing information of a specific class. |
| 1.3.6.1.4.1.9.9.279.1.3.2.1.1 | ColumncaqQueuingParamsClassIndex | not-accessible | current | A class index, which associates with an IP precedence (0 to 8), is defined to reference individual caqQueuingParamsClassEntry. |
| 1.3.6.1.4.1.9.9.279.1.3.2.1.2 | ColumncaqQueuingParamsClassRandDrp | read-only | current | Number of packets dropped when Mean Queue Length is between Minimum Threshold and Maximum Threshold range. |
| 1.3.6.1.4.1.9.9.279.1.3.2.1.3 | ColumncaqQueuingParamsClassTailDrp | read-only | current | Number of packets dropped because the Mean Queue Depth exceeds the Maximum Threshold value. |
| 1.3.6.1.4.1.9.9.279.1.3.2.1.4 | ColumncaqQueuingParamsClassMinThre | read-only | current | Minimum Threshold value in kbps. |
| 1.3.6.1.4.1.9.9.279.1.3.2.1.5 | ColumncaqQueuingParamsClassMaxThre | read-only | current | Maximum Threshold value in kbps. |
| 1.3.6.1.4.1.9.9.279.1.3.2.1.6 | ColumncaqQueuingParamsClassMrkProb | read-only | current | Mark probability denominator. This is the value used in the calculation of a packet being dropped when the average queue size is between the minimum threshold … |
| 1.3.6.1.4.1.9.9.279.2 | NodeciscoAtmQosMIBConform | |||
| 1.3.6.1.4.1.9.9.279.2.1 | NodeciscoAtmQosMIBCompliances | |||
| 1.3.6.1.4.1.9.9.279.2.1.1 | ComplianceciscoAtmQosMIBCompliance | read-only | current | The compliance statement for entities which implement this Cisco ATM QoS MIB. |
| 1.3.6.1.4.1.9.9.279.2.2 | NodeciscoAtmQosMIBGroups | |||
| 1.3.6.1.4.1.9.9.279.2.2.1 | GroupciscoAtmQosVccGroup | current | A collection of objects providing per-VC ATM QoS related info. | |
| 1.3.6.1.4.1.9.9.279.2.2.2 | GroupciscoAtmQosVccAddon1Group | current | Add-on objects providing per-VC ATM QoS related info. | |
| 1.3.6.1.4.1.9.9.279.2.2.3 | GroupciscoAtmQosVpcGroup | current | A collection of objects providing per-VP ATM QoS related info. | |
| 1.3.6.1.4.1.9.9.279.2.2.4 | GroupciscoAtmQosVpcAddon1Group | current | Add-on objects providing per-VP ATM QoS related info. | |
| 1.3.6.1.4.1.9.9.279.2.2.5 | GroupciscoAtmQosVcQueuingGroup | current | A collection of objects providing per-VC queuing/buffering related info. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| VcParamConfigLocation | INTEGER { configDefault(1), configVcDirect(2), configVcClass(3), configVcClassSubInterface(4), configVcClassInterface(5) } | current | The configuration source of a vc parameter: 1 - Not configured - using default 2 - Configured on vc directly 3 - VC-class configured on vc 4 - VC-class configured on sub-interface 5 - VC-class configured on main-interfa… |
| VpState | INTEGER { vpStateInactive(1), vpStateActive(2) } | current | States of virtual path: 1 - Inactive 2 - Active |