CISCO-ATM-SWITCH-FR-IWF-MIB
114 objects
A MIB module for managing Frame Relay to ATM interworking connections, and Frame Relay to Frame Relay switched connections via an ATM switching fabric, on a Cisco ATM switch.
Imported Objects
| ATM-MIB | AtmTrafficDescrParamIndex |
| CISCO-SMI | ciscoMgmt |
| CISCO-TC | Unsigned32 |
| IF-MIB | ifIndex InterfaceIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | RowStatus TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.112 | IdentityciscoAtmSwitchFrIwfMIB | A MIB module for managing Frame Relay to ATM interworking connections, and Frame Relay to Frame Relay switched connections via an ATM switching fabric, on a Ci… | ||
| 1.3.6.1.4.1.9.9.112.1 | NodeciscoAtmSwitchFrIwfMIBObjects | |||
| 1.3.6.1.4.1.9.9.112.1.1 | NodecasfFrTraffic | |||
| 1.3.6.1.4.1.9.9.112.1.1.1 | TablecasfTrafficDescrTable | not-accessible | current | This table contains a set of self-consistent Frame Relay traffic parameters. It is intended to be used to create Frame Relay to ATM interworking connections, h… |
| 1.3.6.1.4.1.9.9.112.1.1.1.1 | RowcasfTrafficDescrEntry | not-accessible | current | Describes a traffic descriptor that is used by Frame Relay connections. |
| 1.3.6.1.4.1.9.9.112.1.1.1.1.1 | ColumncasfTrafficDescrIndex | not-accessible | current | Uniquely identifies a row in this table. |
| 1.3.6.1.4.1.9.9.112.1.1.1.1.2 | ColumncasfTrafficDescrCIR | read-create | current | The value of the Committed Information Rate (CIR) parameter. |
| 1.3.6.1.4.1.9.9.112.1.1.1.1.3 | ColumncasfTrafficDescrBc | read-create | current | The value of the Committed Burst Size (Bc) parameter. |
| 1.3.6.1.4.1.9.9.112.1.1.1.1.4 | ColumncasfTrafficDescrBe | read-create | current | The value of the Excess Burst Size (Be) parameter. |
| 1.3.6.1.4.1.9.9.112.1.1.1.1.5 | ColumncasfTrafficDescrPIR | read-create | current | The value of the Peak Information Rate (PIR) parameter. |
| 1.3.6.1.4.1.9.9.112.1.1.1.1.6 | ColumncasfTrafficDescrServCategory | read-create | current | The service category, as defined for ATM. |
| 1.3.6.1.4.1.9.9.112.1.1.1.1.7 | ColumncasfTrafficDescrAtmIndex | read-create | current | The index of the equivalent entry in the atmTrafficDescrParamTable. |
| 1.3.6.1.4.1.9.9.112.1.1.1.1.8 | ColumncasfTrafficDescrRowStatus | read-create | current | Used to create, delete and modify this row. None of the columnar values (other than this one) can be modified while the row is active. |
| 1.3.6.1.4.1.9.9.112.1.2 | NodecasfFrVC | |||
| 1.3.6.1.4.1.9.9.112.1.2.1 | TablecasfVcEndptTable | not-accessible | current | This table contains information about Frame Relay end-points of FR-ATM interworking connections on the switch. When an entry is created in this table, the agen… |
| 1.3.6.1.4.1.9.9.112.1.2.1.1 | RowcasfVcEndptEntry | not-accessible | current | Models a bidirectional Frame Relay VC end-point. The ifIndex identifies an ifTable entry for a Frame Relay interface on this device. |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.1 | ColumncasfVcEndptDlci | not-accessible | current | The value of the Data Link Connection Identifier (DLCI) which identifies this connection end-point. |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.2 | ColumncasfVcEndptRxTrafficDescrRow | read-create | current | Identifies the entry in the casfTrafficDescrTable which applies to the receive direction at this connection end-point. For connections that negotiate traffic p… |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.3 | ColumncasfVcEndptTxTrafficDescrRow | read-create | current | Identifies the entry in the casfTrafficDescrTable which applies to the transmit direction at this connection end-point. For connections that negotiate traffic … |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.4 | ColumncasfVcEndptRxNegTrafficDescrRow | read-only | current | Identifies the entry in the casfTrafficDescrTable which contains negotiated traffic parameters applied to the receive direction of this connection end-point. T… |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.5 | ColumncasfVcEndptTxNegTrafficDescrRow | read-only | current | Identifies the entry in the casfTrafficDescrTable which contains negotiated traffic parameters applied to the transmit direction of this connection endpoint. T… |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.6 | ColumncasfVcEndptConnKind | read-create | current | The connection kind. The value can be set prior to the row becoming 'active'. To create a pvc connection endpoint, set this value to pvc(1). To create a soft V… |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.7 | ColumncasfVcEndptIwfType | read-create | current | The type of the interworking function. The value can be set prior to the row becoming 'active'. |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.8 | ColumncasfVcEndptClpMode | read-create | current | Specifies how to map from Discard Eligibility (DE) bit on the Frame Relay side to Congestion Loss Priority (CLP) bit on the ATM side. For network interworking,… |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.9 | ColumncasfVcEndptDeMode | read-create | current | Specifies how to map from Congestion Loss Priority (CLP) bit on the ATM side to Discard Eligibility (DE) bit on the Frame Relay side. See the Frame Relay Forum… |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.10 | ColumncasfVcEndptEfciMode | read-create | current | Specifies how to map from FECN field in the Frame Relay PDU to the EFCI field in ATM cells, in case of service interworking. This object does not apply to netw… |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.11 | ColumncasfVcEndptUpcMode | read-create | current | Specifies the action taken by Usage Parameter Control (UPC) at the ingress port. |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.12 | ColumncasfVcEndptSpvcRemoteAddr | read-create | current | The ATM address of the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is spvcIniti… |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.13 | ColumncasfVcEndptSpvcRemoteType | read-create | current | The type of the remote end of the soft VC. This object is instantiated only if the value of casfVcEndptConnKind is spvcInitiator(4) or spvcTarget(5). The agent… |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.14 | ColumncasfVcEndptSpvcRemoteDlci | read-create | current | The DLCI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is… |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.15 | ColumncasfVcEndptSpvcRemoteVpi | read-create | current | The VPI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is … |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.16 | ColumncasfVcEndptSpvcRemoteVci | read-create | current | The VCI value to be used at the remote end of the soft VC. The value can be set prior to the row becoming 'active', and if the value of casfVcEndptConnKind is … |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.17 | ColumncasfVcEndptCreationTime | read-only | current | The time when this row was created. |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.18 | ColumncasfVcEndptRcvdSigStatus | read-only | current | The value of this object identifies the PVC status received via the local in-channel signaling procedures for this PVC end-point. This object is only pertinent… |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.19 | ColumncasfVcEndptRowStatus | read-create | current | Used to create, modify or delete this row. |
| 1.3.6.1.4.1.9.9.112.1.2.1.1.20 | ColumncasfVcSignalStandardCalledIe | read-create | current | Specifies whether or not to signal the standard (from the ATM-Forum PNNI Soft PVC Addendum) format of the Called Soft PVC IE, as opposed to the proprietary enc… |
| 1.3.6.1.4.1.9.9.112.1.3 | NodecasfFrInterface | |||
| 1.3.6.1.4.1.9.9.112.1.3.1 | TablecasfFrLmiTable | not-accessible | current | This table contains frame relay Local Management Interface (LMI) parameters and counters. There is one entry for each frame relay interface. Entries come and g… |
| 1.3.6.1.4.1.9.9.112.1.3.1.1 | RowcasfFrLmiEntry | not-accessible | current | Frame relay LMI objects for a particular frame relay interface, which is identified by the ifIndex value in the INDEX clause. |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.1 | ColumncasfFrLmiProtocol | read-write | current | Identifies the Local In-Channel Signaling Protocol that is used for this frame relay port. |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.2 | ColumncasfFrLmiType | read-write | current | Identifies the Local In-Channel Signaling Procedure that is used for this frame relay port. A dte performs only user-side procedures. A dce performs only netwo… |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.3 | ColumncasfFrLmiUserN391 | read-write | current | Number of status enquiry intervals that pass before issuance of a full status enquiry mes- sage. |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.4 | ColumncasfFrLmiUserN392 | read-write | current | The maximum number of unanswered Status Enquiries the device shall accept before declaring the interface down. |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.5 | ColumncasfFrLmiUserN393 | read-write | current | The number of status polling intervals over which the error threshold is counted. For example, if within N393 number of events the device receives N392 number … |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.6 | ColumncasfFrLmiUserT391 | read-write | current | The number of seconds between successive status enquiry messages. |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.7 | ColumncasfFrLmiNetN392 | read-write | current | The value of the network-side error threshold for this frame relay port. |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.8 | ColumncasfFrLmiNetN393 | read-write | current | The value of the network-side monitored events count for this frame relay port. If, within N393 number of events, the network-side receives N392 number of erro… |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.9 | ColumncasfFrLmiNetT392 | read-write | current | The value of the network-side polling verification timer for this frame relay port. |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.10 | ColumncasfFrLmiEnquiryIns | read-only | current | Number of Status Enquiry messages received. |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.11 | ColumncasfFrLmiEnquiryOuts | read-only | current | Number of Status Enquiry messages sent. |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.12 | ColumncasfFrLmiStatusIns | read-only | current | Number of Status messages received. |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.13 | ColumncasfFrLmiStatusOuts | read-only | current | Number of Status messages sent. |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.14 | ColumncasfFrLmiStatusTimeouts | read-only | current | Number of times when timeout occurred on waiting for Status message |
| 1.3.6.1.4.1.9.9.112.1.3.1.1.15 | ColumncasfFrLmiStatusEnqTimeouts | read-only | current | Number of times when timeout occurred on waiting for Status Enquiry message |
| 1.3.6.1.4.1.9.9.112.1.3.2 | TablecasfConfIfTable | not-accessible | current | Contains an entry for each Frame Relay interface that supports FR-ATM interworking connections. An entry contains interworking related parameters for the inter… |
| 1.3.6.1.4.1.9.9.112.1.3.2.1 | RowcasfConfIfEntry | not-accessible | current | Configuration parameters for interworking at a Frame Relay interface. |
| 1.3.6.1.4.1.9.9.112.1.3.2.1.1 | ColumncasfConfIfAtmAddress | read-only | current | The ATM Address that identifies this interface. This address can be used to setup soft VC's to this interface over an ATM network. |
| 1.3.6.1.4.1.9.9.112.1.3.2.1.2 | ColumncasfConfIfUpcIntent | read-write | current | Specifies the default Usage Parameter Control (UPC) action to use at this interface for connections that do not explicitly specify a UPC action. |
| 1.3.6.1.4.1.9.9.112.1.3.2.1.3 | ColumncasfConfIfBcDefault | read-write | current | Specifies the default Committed Burst Size (Bc) value to use at this interface for connections that do not explicitly specify the value of Bc. |
| 1.3.6.1.4.1.9.9.112.1.3.2.1.4 | ColumncasfConfIfCledSpvcDeModeDef | read-write | current | Specifies the default mapping from Congestion Loss Priority (CLP) bit on the ATM side to Discard Eligibility (DE) bit on the Frame Relay side. This is used whe… |
| 1.3.6.1.4.1.9.9.112.1.3.2.1.5 | ColumncasfConfIfCledSpvcClpModeDef | read-write | current | Specifies the default mapping from Discard Eligibility (DE) bit on the Frame Relay side to Congestion Loss Priority (CLP) bit on the ATM side.This is used when… |
| 1.3.6.1.4.1.9.9.112.1.4 | NodecasfFrCounts | |||
| 1.3.6.1.4.1.9.9.112.1.4.1 | TablecasfVcCountTable | not-accessible | current | A table containing counters at Frame Relay connection end-points. Entries in this table are created and deleted whenever corresponding entries in the casfVcEnd… |
| 1.3.6.1.4.1.9.9.112.1.4.1.1 | RowcasfVcCountEntry | not-accessible | current | Counters at a Frame Relay connection end-point, which is identified by the ifIndex of the Frame Relay interface and the DLCI number. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.1 | ColumncasfVcCountReceivedFrames | read-only | current | Number of frames received. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.2 | ColumncasfVcCountReceivedOctets | read-only | current | Number of octets received. This counter counts octets from the beginning of the frame relay header field to the end of user data. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.3 | ColumncasfVcCountReceivedFECNs | read-only | current | Number of frames received from the network with the FECN (Forward Explicit Congestion Notification) bit set. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.4 | ColumncasfVcCountReceivedBECNs | read-only | current | Number of frames received from the network with the BECN (Backward Explicit Network Congestion) bit set. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.5 | ColumncasfVcCountReceivedDEs | read-only | current | Number of frames received with the Discard Eligibility (DE) bit set. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.6 | ColumncasfVcCountInDiscards | read-only | current | Number of frames received that were discarded at ingress. Possible reasons are policing, congestion. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.7 | ColumncasfVcCountOutDiscards | read-only | current | Number of frames that were to be transmitted but were discarded. Possible reasons are policing, lack of buffers. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.8 | ColumncasfVcCountSentFrames | read-only | current | Number of frames sent. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.9 | ColumncasfVcCountSentOctets | read-only | current | Number of octets sent. This counter counts octets from the beginning of the frame relay header field to the end of user data. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.10 | ColumncasfVcCountSentFECNs | read-only | current | Number of frames that were sent with the FECN bit set. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.11 | ColumncasfVcCountSentBECNs | read-only | current | Number of frames sent with the BECN bit set. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.12 | ColumncasfVcCountSentDEs | read-only | current | Number of frames sent with the DE bit set. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.13 | ColumncasfVcCountTaggedFECNs | read-only | current | Number of frames for which the switch set the FECN bit. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.14 | ColumncasfVcCountTaggedBECNs | read-only | current | Number of frames for which the switch set the BECN bit. |
| 1.3.6.1.4.1.9.9.112.1.4.1.1.15 | ColumncasfVcCountTaggedDEs | read-only | current | Number of frames for which the switch set the DE bit. |
| 1.3.6.1.4.1.9.9.112.1.4.2 | TablecasfVcIwfCountTable | not-accessible | current | This table contains counters at the Frame Relay endpoint of FR-ATM interworking connections. There is an entry in this table corresponding to each entry in cas… |
| 1.3.6.1.4.1.9.9.112.1.4.2.1 | RowcasfVcIwfCountEntry | not-accessible | current | A set of counters at the Frame Relay endpoint of a FR-ATM interworking connection. |
| 1.3.6.1.4.1.9.9.112.1.4.2.1.1 | ColumncasfVcIwfCountInUnknownProts | read-only | current | Frames received with unknown protocol. This event is counted only for connections with service interworking in translation mode. For other types of connections… |
| 1.3.6.1.4.1.9.9.112.1.4.2.1.2 | ColumncasfVcIwfCountOutUnknownProts | read-only | current | Outbound frames that were not transmitted because they contained an unknown protocol. This event is counted only for connections with service interworking in t… |
| 1.3.6.1.4.1.9.9.112.1.4.2.1.3 | ColumncasfVcIwfCountReassemblyTimeouts | read-only | current | The number of frames which could not be completely reassembled due to a reassembly timeout, and were thus discarded before being transmitted on this connection. |
| 1.3.6.1.4.1.9.9.112.1.4.2.1.4 | ColumncasfVcIwfCountLengthErrors | read-only | current | The number of reassembled frames intended to be transmitted on this connection for which the AAL5 PDU trailer length fields did not match the actual PDU length… |
| 1.3.6.1.4.1.9.9.112.1.4.2.1.5 | ColumncasfVcIwfCountCrcErrors | read-only | current | The number of reassembled frames intended to be transmitted on this connection for which the AAL5 PDU had CRC errors, and were thus discarded. |
| 1.3.6.1.4.1.9.9.112.1.4.2.1.6 | ColumncasfVcIwfCountTotalDiscardFrames | read-only | current | The number of frames intended to be transmitted on this connection that were discarded due to any reason including those described in other objects in this tab… |
| 1.3.6.1.4.1.9.9.112.1.5 | NodecasfMapping | |||
| 1.3.6.1.4.1.9.9.112.1.5.1 | TablecasfFAMapTable | not-accessible | current | This table provides mapping from a DLCI on a Frame Relay interface to a VPI/VCI on an internal ATM interface. |
| 1.3.6.1.4.1.9.9.112.1.5.1.1 | RowcasfFAMapEntry | not-accessible | current | Given the ifIndex of a frame relay interface, and a DLCI on that interface, this entry provides the ifIndex and VPI/VCI on the corresponding internal atm inter… |
| 1.3.6.1.4.1.9.9.112.1.5.1.1.1 | ColumncasfFAMapDlci | not-accessible | current | The DLCI value. |
| 1.3.6.1.4.1.9.9.112.1.5.1.1.2 | ColumncasfFAMapInternalAtmInterface | read-only | current | The ifIndex of the internal ATM interface to which this DLCI is mapped. |
| 1.3.6.1.4.1.9.9.112.1.5.1.1.3 | ColumncasfFAMapInternalAtmVpi | read-only | current | The VPI value to which this DLCI is mapped. |
| 1.3.6.1.4.1.9.9.112.1.5.1.1.4 | ColumncasfFAMapInternalAtmVci | read-only | current | The VCI value to which this DLCI is mapped. |
| 1.3.6.1.4.1.9.9.112.1.5.2 | TablecasfAFMapTable | not-accessible | current | This table provides mapping from an atmVclEntry on an internal ATM internal to a casfVcEndptEntry on a Frame Relay interface. |
| 1.3.6.1.4.1.9.9.112.1.5.2.1 | RowcasfAFMapEntry | not-accessible | current | Given the ifIndex of an internal ATM interface, and VPI/VCI, provides the ifIndex of a Frame Relay interface and DLCI, if such mapping exists. The value of ifT… |
| 1.3.6.1.4.1.9.9.112.1.5.2.1.1 | ColumncasfAFMapAtmVpi | not-accessible | current | The VPI value of the Virtual Channel Link (VCL) on the ATM interface. |
| 1.3.6.1.4.1.9.9.112.1.5.2.1.2 | ColumncasfAFMapAtmVci | not-accessible | current | The VCI value of the Virtual Channel Link (VCL) on the ATM interface. |
| 1.3.6.1.4.1.9.9.112.1.5.2.1.3 | ColumncasfAFMapFrIndex | read-only | current | The ifIndex of the frame relay interface that this VCL maps to. |
| 1.3.6.1.4.1.9.9.112.1.5.2.1.4 | ColumncasfAFMapFrDlci | read-only | current | The DLCI on the frame relay interface that this VCL maps to. |
| 1.3.6.1.4.1.9.9.112.3 | NodeciscoAtmSFrIwfMIBConformance | |||
| 1.3.6.1.4.1.9.9.112.3.1 | NodeciscoAtmSFrIwfMIBCompliances | |||
| 1.3.6.1.4.1.9.9.112.3.1.1 | ComplianceciscoAtmSFrIwfMIBCompliance | current | The compliance statement for entities which implement the Cisco Atm Switch FR IWF MIB. | |
| 1.3.6.1.4.1.9.9.112.3.2 | NodeciscoAtmSFrIwfMIBGroups | |||
| 1.3.6.1.4.1.9.9.112.3.2.1 | GroupciscoAtmSFrIwfConfConnGroup | current | A collection of objects which allow configuration of FR-ATM connections on an ATM switch. | |
| 1.3.6.1.4.1.9.9.112.3.2.2 | GroupciscoAtmSFrIwfLmiGroup | current | A collection of objects for configuring and monitoring LMI on an FR interface. | |
| 1.3.6.1.4.1.9.9.112.3.2.3 | GroupciscoAtmSFrIwfConfIfGroup | current | A collection of objects which allow configuration of interworking related parameters on an FR interface. | |
| 1.3.6.1.4.1.9.9.112.3.2.4 | GroupciscoAtmSFrIwfVcStatsGroup | current | A collection of counters at FR VC end-points. | |
| 1.3.6.1.4.1.9.9.112.3.2.5 | GroupciscoAtmSFrIwfVcIwStatsGroup | current | A collection of counters related to FR-ATM interworking at FR VC end-points. | |
| 1.3.6.1.4.1.9.9.112.3.2.6 | GroupciscoAtmSFrIwfMappingGroup | current | A collection of objects that describe the mapping from a FR connection end-point to an ATM VCL, and vice versa. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AtmAddr | OCTET STRING (SIZE(0..40)) | current | An ATM address. The semantics are implied by the length. The address types are: - no address (0 octets) - E.164 (8 octets) - NSAP (20 octets) In addition, when subaddresses are used the AtmAddr may represent the concate… |
| CasfTrafficDescrRow | Unsigned32 (1..2147483647) | current | Identifies an index into the casfTrafficDescrTable. The value 0 signifies that no row has been identified. |
| ConnectionKind | INTEGER { pvc(1), svcIncoming(2), svcOutgoing(3), spvcInitiator(4), spvcTarget(5) } | current | The kind of connection, distinguished by the use of call control. |
| DlciValue | Integer32 (0..4194303) | current | A numerical value identifying a Data Link Connection Identifier (DLCI) for a Frame Relay connection. The valid range of values depends on the format of the address field used, as described in ITU Recommendation Q.922. W… |