CISCO-BSC-MIB
47 objects
The MIB module for BSC. Overview of BSC MIB MIB description The BSC MIB provides the configuration and operational information on Cisco's Binary Synchronous Communications implementation. The following entities are managed: 1) BSC ports (serial interfaces) 2) BSC Control Units (stations on a port) The BSC ports are identified by the interface index, and additional information about this interface can be obtained from the Cisco Serial Interface MIB. The BSC Control Units are identified by the Control Unit address; this is the address used by BSTUN to route the BSC traffic - it is therefore equivalent to the bstunRouteStationAddress in the bstunRouteTable MIB.
Imported Objects
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.36 | IdentityciscoBscMIB | The MIB module for BSC. Overview of BSC MIB MIB description The BSC MIB provides the configuration and operational information on Cisco's Binary Synchronous Co… | ||
| 1.3.6.1.4.1.9.9.36.1 | NodebscObjects | |||
| 1.3.6.1.4.1.9.9.36.1.1 | NodebscPorts | |||
| 1.3.6.1.4.1.9.9.36.1.1.1 | TablebscPortTable | not-accessible | current | A list of port (serial interfaces) which have been configured to support a BSC BSTUN group. |
| 1.3.6.1.4.1.9.9.36.1.1.1.1 | RowbscPortEntry | not-accessible | current | Status and parameter values for a port. |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.1 | ColumnbscPortRole | read-only | current | The router's DLC role to the attached node. If the bscPortRole is primary, this implies that the port is connected to a remote secondary device. If the role is… |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.2 | ColumnbscPortCodeSet | read-only | current | The code set used for the line controls. |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.3 | ColumnbscPortPause | read-only | current | For primary, it is the minimum time to be taken for a cycle round the active poll table; if this time has not elapsed when the bottom of the poll table is reac… |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.4 | ColumnbscPortServlim | read-only | current | This parameter is valid for primary only. It is the number of times the active poll table will be cycled before a non-responding control unit will be polled. T… |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.5 | ColumnbscPortPollTimeout | read-only | current | This parameter is valid for primary only. It is the time that the primary will wait for a response to a poll or select. The units are tenths of a second. The d… |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.6 | ColumnbscPortRecoveryRetries | read-only | current | This is the number of times that a recovery sequence will be retried before the connection is considered to have failed. The default is 5. |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.7 | ColumnbscPortUnknownControlUnitsReceived | read-only | current | Count of frames received from the serial interface with an unsupported control unit address. If this value is non-zero it indicates a problem in the configurat… |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.8 | ColumnbscPortSoftErrors | read-only | current | Count of soft errors; these are errors which have been recovered. This includes CRC errors received, frames which were retransmitted for any reason (NAK receiv… |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.9 | ColumnbscPortHardErrors | read-only | current | Count of hard errors; these are errors which have not been recovered after bscPortRecoveryRetries number of retries, and therefore the connection has been term… |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.10 | ColumnbscPortProtocolViolations | read-only | current | Count of protocol violations. This counter is incremented when an unexpected BSC Data Link Control character is received from the remote device; that is, the c… |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.11 | ColumnbscPortHostTimeout | read-only | current | This parameter is valid for interfaces configured secondary which additionally are running local-acknowledgement. If the configuration does not match the value… |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.12 | ColumnbscPortSpecPoll | read-only | current | This parameter is valid for primary, local-acknowledgement interfaces only. It is set to TRUE when the interface is configured to treat specific polls as gener… |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.13 | ColumnbscPortVirtualAddress | read-only | current | This parameter is valid for contention only. It is the address to be used for this interface when the remote peer router is being used as a concentrator. The d… |
| 1.3.6.1.4.1.9.9.36.1.1.1.1.14 | ColumnbscPortContentionDialTimeout | read-only | current | This parameter is valid for dialContention only. It is the amount of time an interface can be quiescent before return the interface to the dial-in pool. The de… |
| 1.3.6.1.4.1.9.9.36.1.2 | NodebscControlUnits | |||
| 1.3.6.1.4.1.9.9.36.1.2.1 | TablebscControlUnitTable | not-accessible | current | A table containing information about specific Control Units. |
| 1.3.6.1.4.1.9.9.36.1.2.1.1 | RowbscCUEntry | not-accessible | current | The information regarding a single Control Unit. |
| 1.3.6.1.4.1.9.9.36.1.2.1.1.1 | ColumnbscCUAddress | not-accessible | current | This value is the poll address of the BSC Control Unit. This address must be unique within a BSTUN Group. |
| 1.3.6.1.4.1.9.9.36.1.2.1.1.2 | ColumnbscCUState | read-only | current | State of the BSC Control Unit; when active this indicates that the remote Control Unit is polling or responding to polls. |
| 1.3.6.1.4.1.9.9.36.1.2.1.1.3 | ColumnbscCUBytesSent | read-only | current | Count of sent bytes (octets). Includes all control characters. |
| 1.3.6.1.4.1.9.9.36.1.2.1.1.4 | ColumnbscCUBytesReceived | read-only | current | Count of received bytes (octets). Includes all control characters. |
| 1.3.6.1.4.1.9.9.36.1.2.1.1.5 | ColumnbscCUTotalFramesSent | read-only | current | Count of sent frames (blocks). Includes all control frames. |
| 1.3.6.1.4.1.9.9.36.1.2.1.1.6 | ColumnbscCUTotalFramesReceived | read-only | current | Count of received frames (blocks). Includes all control frames. |
| 1.3.6.1.4.1.9.9.36.1.2.1.1.7 | ColumnbscCUDataFramesSent | read-only | current | Count of sent data frames (blocks). |
| 1.3.6.1.4.1.9.9.36.1.2.1.1.8 | ColumnbscCUDataFramesReceived | read-only | current | Count of received data frames (blocks). |
| 1.3.6.1.4.1.9.9.36.1.2.1.1.9 | ColumnbscCUSoftErrors | read-only | current | Count of soft errors; these are errors which have been recovered. This includes CRC errors received, frames which were retransmitted for any reason (NAK receiv… |
| 1.3.6.1.4.1.9.9.36.1.2.1.1.10 | ColumnbscCUHardErrors | read-only | current | Count of hard errors; these are errors which have not been recovered after bscPortRecoveryRetries number of retries, and therefore the connection has been term… |
| 1.3.6.1.4.1.9.9.36.1.2.1.1.11 | ColumnbscCUProtocolViolations | read-only | current | Count of protocol violations. This counter is incremented when an unexpected BSC Data Link Control character is received from the remote device; that is, the c… |
| 1.3.6.1.4.1.9.9.36.1.3 | NodebscExtAddresses | |||
| 1.3.6.1.4.1.9.9.36.1.3.1 | TablebscExtAddressTable | not-accessible | current | List of all addresses configured by the bsc extended-address command. This applies only to interfaces with an ifType of 'bsc'. The address entries must be uniq… |
| 1.3.6.1.4.1.9.9.36.1.3.1.1 | RowbscExtAddressEntry | not-accessible | current | The information regarding a single extended addresses. |
| 1.3.6.1.4.1.9.9.36.1.3.1.1.1 | ColumnbscExtPollAddress | not-accessible | current | The poll address of the station configured by the bsc extended-address command. |
| 1.3.6.1.4.1.9.9.36.1.3.1.1.2 | ColumnbscExtSelectAddress | read-only | current | The select address of the station configured by the bsc extended-address command. |
| 1.3.6.1.4.1.9.9.36.3 | NodebscMibConformance | |||
| 1.3.6.1.4.1.9.9.36.3.1 | NodebscMibCompliances | |||
| 1.3.6.1.4.1.9.9.36.3.1.1 | CompliancebscMibCompliance | obsolete | The compliance statement for BSTUN. | |
| 1.3.6.1.4.1.9.9.36.3.1.2 | CompliancebscMibComplianceRev1 | current | The compliance statement for all Cisco Systems that implement BSC functions. | |
| 1.3.6.1.4.1.9.9.36.3.2 | NodebscMibGroups | |||
| 1.3.6.1.4.1.9.9.36.3.2.1 | GroupbscPortsGroup | obsolete | A collection of objects providing information about BSC enabled interfaces. | |
| 1.3.6.1.4.1.9.9.36.3.2.2 | GroupbscControlUnitsGroup | current | A collection of objects providing information about BSC Control Units . | |
| 1.3.6.1.4.1.9.9.36.3.2.3 | GroupbscPortsGroupRev1 | current | A collection of objects providing information about BSC enabled interfaces. | |
| 1.3.6.1.4.1.9.9.36.3.2.4 | GroupbscExtAddressGroup | current | A collection of objects providing information about BSC extended addresses. |