CISCO-C2900-MIB
117 objects
The MIB module for Catalyst 2900 enterprise specific information
Imported Objects
| CISCO-SMI | ciscoMgmt |
| IF-MIB | InterfaceIndex |
| RFC1213-MIB | DisplayString sysName |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DateAndTime TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.87 | IdentityciscoC2900MIB | The MIB module for Catalyst 2900 enterprise specific information | ||
| 1.3.6.1.4.1.9.9.87.1 | Nodec2900MIBObjects | |||
| 1.3.6.1.4.1.9.9.87.1.1 | Nodec2900SysInfo | |||
| 1.3.6.1.4.1.9.9.87.1.1.1 | Scalarc2900InfoBoardRevision | read-only | current | Returns the revision number of the main board on which the FastSwitch firmware resides. |
| 1.3.6.1.4.1.9.9.87.1.1.2 | Scalarc2900InfoPeakBuffersUsed | read-only | current | The maximum number of 64-byte buffers used in the main switch buffer pool. |
| 1.3.6.1.4.1.9.9.87.1.1.3 | Scalarc2900InfoTotalBufferDepth | read-only | current | It represents the total number of 64-byte buffers in the Ethernet Controller. |
| 1.3.6.1.4.1.9.9.87.1.1.4 | Scalarc2900InfoAddrCapacity | read-only | current | The system-wide maximum number of MAC addresses supported in the address table, a primary resource when forwarding frames through a bridge. The address table i… |
| 1.3.6.1.4.1.9.9.87.1.1.5 | Scalarc2900InfoRestrictedStaticAddrCapacity | read-only | current | The system-wide maximum number of static addresses supported. A static address is one that has explicit source port filtering information assigned. This number… |
| 1.3.6.1.4.1.9.9.87.1.1.6 | Scalarc2900InfoSelfTestFailed | read-only | current | A bit array where the presence of a particular bit indicates a failure of a specific Power On Self Test. Bit 0 - System Board Failure Bit 1 - CPU Buffer Failur… |
| 1.3.6.1.4.1.9.9.87.1.1.7 | Scalarc2900InfoUtilDisplay | read-only | current | The number of utilization meter LEDs currently lit on the front panel, if the value of c2900InfoVisualIndicatorMode is selected as utilization(4). More LEDs ar… |
| 1.3.6.1.4.1.9.9.87.1.1.8 | Scalarc2900InfoVisualIndicatorMode | read-only | current | This object reflects what is currently selected as the visual indication mode, selected by the mode button. The portStatus(1) mode uses the visual LEDS to indi… |
| 1.3.6.1.4.1.9.9.87.1.1.9 | Scalarc2900InfoRedunantPowerSupplyInfo | read-only | current | The switch allows a redundant power supply in addition to its local power supply. Only one power source can be supplying power to a unit. absent(1) :the redund… |
| 1.3.6.1.4.1.9.9.87.1.1.10 | Scalarc2900InfoBoardIdentifier | read-only | current | Returns the identifier of the main board on which the FastSwitch firmware resides. |
| 1.3.6.1.4.1.9.9.87.1.2 | Nodec2900SysConfig | |||
| 1.3.6.1.4.1.9.9.87.1.2.1 | Scalarc2900ConfigAddressViolationAction | read-write | deprecated | Indicates what action to take when an address violation (an address mismatch or duplication) occurs on a secure port. The default action is to do nothing. doNo… |
| 1.3.6.1.4.1.9.9.87.1.2.2 | Scalarc2900ConfigBroadcastStormAlarm | read-write | deprecated | When set to true(1), the switch will generate a broadcastStorm notification upon detecting a port is receiving broadcast packets at a rate higher than or equal… |
| 1.3.6.1.4.1.9.9.87.1.3 | Tablec2900ModuleTable | not-accessible | current | A list of module entries. |
| 1.3.6.1.4.1.9.9.87.1.3.1 | Rowc2900ModuleEntry | not-accessible | current | Entry containing status information about one module in the c2900 chassis. |
| 1.3.6.1.4.1.9.9.87.1.3.1.1 | Columnc2900ModuleIndex | not-accessible | current | Module index into c2900ModuleTable . |
| 1.3.6.1.4.1.9.9.87.1.3.1.2 | Columnc2900ModuleStatus | read-only | current | The overall status of of the module. |
| 1.3.6.1.4.1.9.9.87.1.3.1.3 | Columnc2900ModuleType | read-only | current | The type of module installed in malibu switch. |
| 1.3.6.1.4.1.9.9.87.1.3.1.4 | Columnc2900ModuleHwVersion | read-only | current | The hardware version of the module. The format of the version string x.y.z where x,y, and z are hardware register field values. |
| 1.3.6.1.4.1.9.9.87.1.3.1.5 | Columnc2900ModuleSwVersion | read-only | current | The software version of the module. |
| 1.3.6.1.4.1.9.9.87.1.4 | Nodec2900Port | |||
| 1.3.6.1.4.1.9.9.87.1.4.1 | Tablec2900PortTable | not-accessible | current | A list of port entries. The number of entries is determined by the number of modules in the chassis and the number of ports on each module. |
| 1.3.6.1.4.1.9.9.87.1.4.1.1 | Rowc2900PortEntry | not-accessible | current | Entry containing information for a particular switched port on a module installed. The entries are not created or deleted by management commands. |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.1 | Columnc2900PortModuleIndex | not-accessible | current | An index value that uniquely identifies the module where this port is located. The value is determined by the chassis slot number into which the module is plug… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.2 | Columnc2900PortIndex | not-accessible | current | An index value that uniquely identifies this port within a module. |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.3 | Columnc2900PortUsageApplication | read-write | current | This object indicates how the port is to be used. The variable usage applications are shown above. These applications are defined such that they are mutually e… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.4 | Columnc2900PortGroupIndex | read-write | current | This object is meaningful only when the corresponding c2900PortUsageApplication is portGrouping. Ports assigned with the same value of c2900PortGroupIndex belo… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.5 | Columnc2900PortMayLearnAddress | read-write | deprecated | This object reflects an internal state of the port with regard to its ability to learn new addresses. Certain port configurations such as learning time limit, … |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.6 | Columnc2900PortMayForwardFrames | read-write | current | This object reflects an internal state of the port with regard to its ability to forward frames. A port sometimes stops forwarding frames when it is blocked by… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.7 | Columnc2900PortBufferCongestionControl | read-only | deprecated | Seting this object to true(1) allows the switch to run its buffer congestion control algorithm on the port. Setting the object to false(2) disallows such contr… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.8 | Columnc2900PortBufferCongestionThreshholdPercent | read-only | current | The port buffer congestion threshold provides an early warning to the switch that the port is about to exhaust all its guaranteed buffers, leading to congestio… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.9 | Columnc2900PortFrameAge | read-only | current | The aging interval in milliseconds after which old frames queued for transmission on this port are discarded. |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.10 | Columnc2900PortAddrSecureMaxAddresses | read-write | current | The maximum number of secure addresses that can be learned on this port when it is a secure port. This number should be always higher than c2900PortAddrSecureC… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.11 | Columnc2900PortAddrSecureCurrentAddresses | read-only | current | The current number of statically assigned unicast addresses on the port. |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.12 | Columnc2900PortAddrSecureAddrViolations | read-only | current | The number of times a source address was seen on this port which duplicates a secured address configured on another port, plus the number of times a source add… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.13 | Columnc2900PortNumberOfLearnedAddresses | read-only | current | The current number of dynamically learned addresses on the port. |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.14 | Columnc2900PortNumberOfDroppedAddresses | read-only | current | The number of times an address could not be learned or assigned for the port because its address table was full at one time. |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.15 | Columnc2900PortClearAddresses | read-write | current | Set to true(1) to delete all learned and assigned dynamic, static and secure unicast addresses the port currently has. Setting the object to false(2) has no ef… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.16 | Columnc2900PortFloodUnknownMulticasts | read-write | current | Set to true(1) to allow forwarding to this port frames addressed to multicast addresses that have not been configured for the port. Set to false(2) to filter a… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.17 | Columnc2900PortFloodUnknownUnicasts | read-write | current | This object controls the forwarding of unknown unicast frames to this port. When set to true(1), the switch will, upon receiving a frame with an unknown unicas… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.18 | Columnc2900PortLinkbeatStatus | read-only | current | This object depends on the physical layer in use and indicates the current port linkbeat status: if the physical link between two devices is properly connected… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.19 | Columnc2900PortBroadcastStormAction | read-write | current | Indicates what action to take when the broadcast rising threshold for a port is reached. The default action is to forwardBroadcast(2) as usual for all broadcas… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.20 | Columnc2900PortBroadcastRisingThreshold | read-write | current | The broadcast rising threshold is measured in the number of broadcast frames received on a port in a second. When the number of broadcast frames received per s… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.21 | Columnc2900PortBroadcastFallingThreshold | read-write | current | The broadcast falling threshold is measured in number of broadcast frames received on a port in a second. When the falling threshold is crossed and the c2900Po… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.22 | Columnc2900PortStatus | read-only | current | The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the … |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.23 | Columnc2900PortTestResult | read-only | current | This object indicates if the port passed power on self test or not. If the value of this object is true(1), the port passed test. If the value of this object i… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.24 | Columnc2900PortVisualIndicator | read-only | current | This object is used to indicate the current color of a LED. If a LED is flashing, the value of this object will represent the color of the LED at that instant … |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.25 | Columnc2900PortIfIndex | read-only | current | The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this port. |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.26 | Columnc2900PortAddressViolationAction | read-write | current | Indicates what action to take when an address violation (an address mismatch or duplication) occurs on a secure port. The default action is to do nothing. doNo… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.27 | Columnc2900PortBroadcastStormAlarm | read-write | current | When set to true(1), the switch will generate a broadcastStorm notification upon detecting a port is receiving broadcast packets at a rate higher than or equal… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.28 | Columnc2900PortMonitorDestinationPort | read-write | current | Switch Port (c2900PortSwitchPortIndex) index value of the port that is to be monitored by this port. A value of zero can't be used to do set, it is used to ret… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.29 | Columnc2900PortSwitchPortIndex | read-only | current | Switch port index of a port is a value that uniquely identifies the port within a switch. This is obtained from the port index (c2900PortIndex) and the module … |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.30 | Columnc2900PortMonitoredPortMap | read-only | current | Indicates which ports are actually being monitored. The octet string contains one bit per port. Each bit within the octet string represents one port of the dev… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.31 | Columnc2900PortDuplexState | read-write | current | Set to fullduplex(1) to operate in full duplex mode, port will allow simultaneous transmit and receive which can double its bandwidth. Set to halfduplex(2) to … |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.32 | Columnc2900PortDuplexStatus | read-only | current | The status of duplex mode on this port. When linkbeat is not present, halfduplex is always reported. When linkbeat is present, the result of full duplex auto-n… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.33 | Columnc2900PortAdminSpeed | read-write | current | The object controls the speed of the port. The current operational speed of the port can be determined from ifSpeed. |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.34 | Columnc2900PortNoMonitorDestinationPort | read-write | current | Switch Port (c2900PortSwitchPortIndex) index value of the port that is to be removed from the monitored list. A value of zero can't be used to do set, it is us… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.35 | Columnc2900Portdot1dBasePort | read-only | current | This is the dot1dBasePort associated with this port. |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.36 | Columnc2900PortSpantreeFastStart | read-write | current | Indicates whether the port is operating in spantree fast start mode. A port with fast start enabled is immediately put in spanning tree forwarding state on lin… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.37 | Columnc2900PortVoiceVlanId | read-write | current | The Voice Virtual Vlan ID (VVID) to which this port belongs to. If the VVID is not supported on the port, this MIB object will not be configurable and will ret… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.38 | Columnc2900PortAddrSecureAgingTime | read-write | current | The aging interval in minutes for each secure address entry on a given port. Depending on the type of aging the secure address will age out after the expiratio… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.39 | Columnc2900PortAddrSecureAgingType | read-write | current | If the value of this object on a given port is absolute - all the secure addresses on this port will age out exactly after the aging time configured for this p… |
| 1.3.6.1.4.1.9.9.87.1.4.1.1.40 | Columnc2900PortAddrSecureAgingStatic | read-write | current | Set to true(1) to enable aging for statically configured secure addresses on one port. Disable the aging for statically configured secure addresses if set to f… |
| 1.3.6.1.4.1.9.9.87.1.4.2 | Tablec2900PortStatsTable | not-accessible | current | A list of port entries. The number of entries is determined by the number of modules in the chassis and the number of ports on each module. |
| 1.3.6.1.4.1.9.9.87.1.4.2.1 | Rowc2900PortStatsEntry | not-accessible | current | Entry containing information for a particular switched port on a module installed. The entry cannot be created or deleted. |
| 1.3.6.1.4.1.9.9.87.1.4.2.1.1 | Columnc2900PortRxNoBwFrames | read-only | current | A count of frames received on this port that were discarded due to a lack of bandwidth resources in the Catalyst Switch forwarding engine. |
| 1.3.6.1.4.1.9.9.87.1.4.2.1.2 | Columnc2900PortRxNoBufferFrames | read-only | current | A count of frames received that were discarded due to a lack of frame buffer resources in the Catalyst Switch forwarding engine. |
| 1.3.6.1.4.1.9.9.87.1.4.2.1.3 | Columnc2900PortRxNoDestUniFrames | read-only | current | A count of unicast frames received that were discarded, because the forwarding rules stipulate that they are not be forwarded. |
| 1.3.6.1.4.1.9.9.87.1.4.2.1.4 | Columnc2900PortRxNoDestMultiFrames | read-only | current | A count of multicast frames received that were discarded, because they have not been configured for the port. |
| 1.3.6.1.4.1.9.9.87.1.4.2.1.5 | Columnc2900PortRxSuppressBcastFrames | read-only | deprecated | A count of broadcast frames received that were discarded because of the threshold-based broadcast suppression. This object is deprecated, because there is no w… |
| 1.3.6.1.4.1.9.9.87.1.4.2.1.6 | Columnc2900PortRxFcsErrFrames | read-only | current | The total number of frames received with FCS errors. This total includes all frames received with an FCS error and an integral number of bytes. Unlike RFC1650'… |
| 1.3.6.1.4.1.9.9.87.1.4.2.1.7 | Columnc2900PortCollFragFrames | read-only | current | The total number of frames whose lengths are less than 64 and have bad FCS values. The preamble and sfd fields are excluded from the byte count of a frame whil… |
| 1.3.6.1.4.1.9.9.87.1.4.2.1.8 | Columnc2900PortTxMulticastFrames | read-only | current | A count of frames that are successfully transmitted and are directed to a multicast address. Unlike RFC1573's ifOutMulticastPkts, this object does not include … |
| 1.3.6.1.4.1.9.9.87.1.4.2.1.9 | Columnc2900PortTxBroadcastFrames | read-only | current | A count of frames that are successfully transmitted and are directed to the broadcast address. Unlike RFC1573's ifOutBroadcastPkts, this object does not includ… |
| 1.3.6.1.4.1.9.9.87.1.5 | Nodec2900BandwidthUsage | |||
| 1.3.6.1.4.1.9.9.87.1.5.1 | Scalarc2900BandwidthUsageCurrent | read-only | current | The current bandwidth consumed. The measurement unit is in megabits per second (1,000,000 bits/second). This value gives a reasonable estimate of the amount of… |
| 1.3.6.1.4.1.9.9.87.1.5.2 | Scalarc2900BandwidthUsageMaxPeakEntries | read-only | current | The maximum number of entries c2900BandwidthUsagePeakTable can have. |
| 1.3.6.1.4.1.9.9.87.1.5.3 | Scalarc2900BandwidthUsagePeakInterval | read-write | current | This object specifies the length of time which forms a peak bandwidth measurement interval. A write to this object with any new value restarts the peak bandwid… |
| 1.3.6.1.4.1.9.9.87.1.5.4 | Scalarc2900BandwidthUsagePeakRestart | read-write | current | Set to true(1) to clear the c2900BandwidthUsagePeakTable and restart the peak bandwidth recording. No action will be taken if this object is set to false(2). T… |
| 1.3.6.1.4.1.9.9.87.1.5.5 | Scalarc2900BandwidthUsageCurrentPeakEntry | read-only | current | A value identifying an instance of the c2900BandwidthUsagePeakIndex where the peak bandwidth estimation is most recent. |
| 1.3.6.1.4.1.9.9.87.1.5.6 | Tablec2900BandwidthUsagePeakTable | not-accessible | current | A list of entries containing peak bandwidth usages in a number of recording interval. After being cleared, entries are added to the bandwidthUsagePeakTable wit… |
| 1.3.6.1.4.1.9.9.87.1.5.6.1 | Rowc2900BandwidthUsagePeakEntry | not-accessible | current | Information about peak bandwidth usage in a recording interval. |
| 1.3.6.1.4.1.9.9.87.1.5.6.1.1 | Columnc2900BandwidthUsagePeakIndex | read-only | current | Number from one to c2900BandwidthUsageMaxPeakEntries identifying a particular c2900BandwithUsagePeakEntry. |
| 1.3.6.1.4.1.9.9.87.1.5.6.1.2 | Columnc2900BandwidthUsageStartTime | read-only | current | The time that marks the start of this recording interval. |
| 1.3.6.1.4.1.9.9.87.1.5.6.1.3 | Columnc2900BandwidthUsagePeak | read-only | current | The maximum bandwidth usage of any measurement interval within this recording interval. This value is an estimate of the highest amount of traffic flowing thro… |
| 1.3.6.1.4.1.9.9.87.1.5.6.1.4 | Columnc2900BandwidthUsagePeakTime | read-only | current | The start time of the measurement interval. |
| 1.3.6.1.4.1.9.9.87.2 | Nodec2900MibNotifications | |||
| 1.3.6.1.4.1.9.9.87.2.0 | Nodec2900MibNotificationsPrefix | |||
| 1.3.6.1.4.1.9.9.87.2.0.1 | Notificationc2900AddressViolation | current | The addressViolation notification is generated when an address violation is detected on a secured port. The generation of the addressViolation notification can… | |
| 1.3.6.1.4.1.9.9.87.2.0.2 | Notificationc2900BroadcastStorm | current | The broadcastStorm notification is generated upon detecting a port is receiving broadcast packets at a rate crossing the specified broadcast threshold. This tr… | |
| 1.3.6.1.4.1.9.9.87.2.0.3 | Notificationc2900RpsFailed | current | A redundant power system (RPS) is connected to the switch. The RpsFailed notification is generated upon detecting RPS failure. | |
| 1.3.6.1.4.1.9.9.87.3 | Nodec2900MIBConformance | |||
| 1.3.6.1.4.1.9.9.87.3.1 | Nodec2900MIBCompliances | |||
| 1.3.6.1.4.1.9.9.87.3.1.1 | Compliancec2900MIBCompliance | deprecated | The compliance statement for all c2900 switch. | |
| 1.3.6.1.4.1.9.9.87.3.1.2 | Compliancec2900MIBComplianceSA5 | deprecated | The compliance statement for all c2900 switch. | |
| 1.3.6.1.4.1.9.9.87.3.1.3 | Compliancec2900MIBComplianceSA3 | deprecated | The compliance statement for all c2900 switch. | |
| 1.3.6.1.4.1.9.9.87.3.1.4 | Compliancec2900MIBComplianceSA7 | deprecated | The compliance statement for all c2900 switch. | |
| 1.3.6.1.4.1.9.9.87.3.1.5 | Compliancec2900MIBComplianceWC2 | deprecated | The compliance statement for all c2900 switch. | |
| 1.3.6.1.4.1.9.9.87.3.1.6 | Compliancec2900MIBComplianceWC4 | current | The compliance statement for all c2900 switch. | |
| 1.3.6.1.4.1.9.9.87.3.2 | Nodec2900MIBGroups | |||
| 1.3.6.1.4.1.9.9.87.3.2.1 | Groupc2900SysInfoGroup | current | The collection of objects which are used to provide the general switch information. | |
| 1.3.6.1.4.1.9.9.87.3.2.2 | Groupc2900SysConfigGroup | deprecated | The collection of objects which are used to configure the switch. | |
| 1.3.6.1.4.1.9.9.87.3.2.3 | Groupc2900ModuleGroup | current | The object is used to provide the module status. | |
| 1.3.6.1.4.1.9.9.87.3.2.4 | Groupc2900PortGroup | deprecated | The collection of objects which are used to provide port status and configuration. | |
| 1.3.6.1.4.1.9.9.87.3.2.5 | Groupc2900PortStatsGroup | deprecated | The collection of objects which are used to provide port stats. | |
| 1.3.6.1.4.1.9.9.87.3.2.6 | Groupc2900BandwidthUsageGroup | current | The collection of objects which are used to provide the bandwidth information. | |
| 1.3.6.1.4.1.9.9.87.3.2.7 | Groupc2900PortGroupSA3 | deprecated | The collection of objects which are used to provide port status and configuration. | |
| 1.3.6.1.4.1.9.9.87.3.2.8 | Groupc2900PortStatsGroupSA3 | deprecated | The collection of objects which are used to provide port stats. | |
| 1.3.6.1.4.1.9.9.87.3.2.9 | Groupc2900PortGroupSA5 | deprecated | The collection of objects which are used to provide port status and configuration. | |
| 1.3.6.1.4.1.9.9.87.3.2.10 | Groupc2900PortGroupSA7 | deprecated | The collection of objects which are used to provide port status and configuration. | |
| 1.3.6.1.4.1.9.9.87.3.2.11 | Groupc2900PortGroupWC2 | deprecated | The collection of objects which are used to provide port status and configuration, includes voice vlan id. | |
| 1.3.6.1.4.1.9.9.87.3.2.12 | Groupc2900PortGroupWC4 | current | The collection of objects which are used to provide port status and configuration, includes voice vlan id and port-security aging. | |
| 1.3.6.1.4.1.9.9.87.3.2.13 | Groupc2900NotificationsGroup | current | The set of notifications provided by c2900 device. | |
| 1.3.6.1.4.1.9.9.87.3.2.14 | Groupc2900PortStatsGroupRev1 | current | The collection of objects which are used to provide port stats. |