CISCO-CIPCSNA-MIB
69 objects
No module-level DESCRIPTION found.
Imported Objects
| CISCO-CHANNEL-MIB | cipCardDtrBrdIndex cipCardEntryIndex cipCardSubChannelIndex |
| CISCO-SMI | ciscoMgmt |
| CISCO-SNA-LLC-MIB | llcPortVirtualIndex llcSapNumber |
| RFC1213-MIB | ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | RowStatus TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.20.1.3.1.1 | IdentityciscoCipCsnaMIB | read-only | current | |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1 | NodecipCsnaObjects | |||
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1 | NodecipCsnaChannel | |||
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.1 | TablecipCardCsnaAdminTable | not-accessible | current | This table contains configuration information for the Channel Systems Network Architecture (CSNA) feature on the CMCC card. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.1.1 | RowcipCardCsnaAdminEntry | not-accessible | current | A list of CSNA configuration values. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.1.1.1 | ColumncipCardCsnaAdminPath | read-create | current | The Channel Path for this Channel Systems Network Architecture table entry. For more information see the textual convention ChannelPath. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.1.1.2 | ColumncipCardCsnaAdminDevice | read-create | current | Two octet hex device address for the device the SNA host will use to communicate with the CSNA feature on the CMCC card. For more information see the textual c… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.1.1.3 | ColumncipCardCsnaAdminBlockDelayTime | read-create | current | The Block Delay Time is the maximum amount of time the CSNA feature can hold a set of requests before it must transmit the block to the host. The Block must be… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.1.1.4 | ColumncipCardCsnaAdminBlockDelayLength | read-create | current | The Block Delay Length is the suggested size of a block before it is transmitted to the host. The Block Delay Length is used to force a transmit of a block whe… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.1.1.5 | ColumncipCardCsnaAdminMaxBlockLength | read-create | current | The Maximum block length is the maximum size that an inbound channel I/O block my attain before being sent to the host. The block must be smaller or equal to t… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.1.1.6 | ColumncipCardCsnaAdminRowStatus | read-create | current | This object is used by a Management Station to create or delete the row entry in the cipCardCsnaAdminTable following the the RowStatus textual convention. Upon… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.2 | TablecipCardCsnaOperTable | not-accessible | current | This table contains operation values and status information for the Channel Systems Network Architecture (CSNA) feature on the CMCC card. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.2.1 | RowcipCardCsnaOperEntry | not-accessible | current | A list of CSNA operational and status values. The entries are created by the Agent. They have read-only access. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.2.1.1 | ColumncipCardCsnaOperState | read-only | current | The current state of the CSNA entry. The values have the following meanings: closed - Link is closed. pendingOpen - An Open Subchannel command has been receive… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.2.1.2 | ColumncipCardCsnaOperSlowDownState | read-only | current | The current state of the CSNA slow down condition. A channel device will turn on the slow down bit whenever insufficient buffering is available to receive data… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.2.1.3 | ColumncipCardCsnaOperBlockDelayTime | read-only | current | The current Block Delay Time value being used by this instance of CSNA path/device (subchannel). |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.2.1.4 | ColumncipCardCsnaOperBlockDelayLength | read-only | current | The current Block Delay Length being used by this instance of CSNA path/device (subchannel). |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.2.1.5 | ColumncipCardCsnaOperMaxBlockLength | read-only | current | The current Maximum block length being used by this instance of CSNA path/device (subchannel). |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3 | TablecipCardCsnaStatsTable | not-accessible | current | This table contains statistics information for the Channel Systems Network Architectures (CSNA) feature on the CMCC card. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1 | RowcipCardCsnaStatsEntry | not-accessible | current | A list of CSNA statistics. The entries are created by the Agent. They have read-only access. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.1 | ColumncipCardCsnaStatsBlocksTxd | read-only | current | The number of Blocks Transmitted. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.2 | ColumncipCardCsnaStatsBlocksRxd | read-only | current | The number of Blocks Received. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.3 | ColumncipCardCsnaStatsBytesTxd | read-only | current | The number of Bytes Transmitted. NOTE: To support SNMP Version 1 Managers, this variable is supplied as a 32 bit value which can wrap very frequently. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.4 | ColumncipCardCsnaStatsHCBytesTxd | read-only | current | The number of Bytes Transmitted. NOTE: This is a 64 bit (High Capacity) version of the cipCardCsnaStatsBytesTxd counter for use with SNMP Version 2 Managers |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.5 | ColumncipCardCsnaStatsBytesRxd | read-only | current | The number of Bytes Received. NOTE: To support SNMP Version 1 Managers, this variable is supplied as a 32 bit value which can wrap very frequently. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.6 | ColumncipCardCsnaStatsHCBytesRxd | read-only | current | The number of Bytes Received. NOTE: This is a 64 bit (High Capacity) version of the cipCardCsnaStatsBytesRxd counter for use with SNMP Version 2 Managers |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.7 | ColumncipCardCsnaStatsBlocksTxByBlockDelayTime | read-only | current | The number of Blocks Transmitted when the Block Delay Time has been exceeded. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.8 | ColumncipCardCsnaStatsBytesTxByBlockDelayTime | read-only | current | The number of Bytes Transmitted when the Block Delay Time has been exceeded. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.9 | ColumncipCardCsnaStatsHCBytesTxByBlockDelayTime | read-only | current | The number of Bytes Transmitted when the Block Delay Time has been exceeded. NOTE: This is a 64 bit (High Capacity) version of the cipCardCsnaStatsBytesTxByBlo… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.10 | ColumncipCardCsnaStatsBlocksTxByBlockDelayLength | read-only | current | The number of Blocks Transmitted when the suggested Block Delay Length has been exceeded. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.11 | ColumncipCardCsnaStatsBytesTxByBlockDelayLength | read-only | current | The number of Bytes Transmitted when the suggested Block Delay Length has been exceeded. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.12 | ColumncipCardCsnaStatsHCBytesTxByBlockDelayLength | read-only | current | The number of Bytes Transmitted when the suggested Block Delay Length has been exceeded. NOTE: This is a 64 bit (High Capacity) version of the cipCardCsnaStats… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.13 | ColumncipCardCsnaStatsBlocksTxByMaxBlockLength | read-only | current | The number of Blocks Transmitted when the Maximum block length has been exceeded. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.14 | ColumncipCardCsnaStatsBytesTxByMaxBlockLength | read-only | current | The number of Bytes Transmitted when the Maximum block length has been exceeded. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.15 | ColumncipCardCsnaStatsHCBytesTxByMaxBlockLength | read-only | current | The number of Bytes Transmitted when the Maximum block length has been exceeded. NOTE: This is a 64 bit (High Capacity) version of the cipCardCsnaStatsBytesTxB… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.16 | ColumncipCardCsnaStatsSlowDownsReceived | read-only | current | The number of times the slow down bit was detected in a channel I/O block received from VTAM. This condition causes the router to stop transmitting data to VTA… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.1.3.1.17 | ColumncipCardCsnaStatsSlowDownsSent | read-only | current | The number of times the slow down bit was set by the router to stop VTAM from sending any more channel I/O blocks. This condition stays in effect until the rou… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.2 | NodecipSession | |||
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.2.1 | TablecipCardSessionsAdminTable | not-accessible | current | This table contains configured values for CSNA sessions supported on the CMCC card. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.2.1.1 | RowcipCardSessionsAdminEntry | not-accessible | current | A list of CMCC specific Session configuration values. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.2.1.1.1 | ColumncipCardAdminMaxLlc2Sessions | read-write | current | The configured maximum number of LLC2 sessions allowed on a CMCC card. A value of zero indicates that the maximum should only be limited by the amount of avail… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.2.2 | TablecipCardSessionsOperTable | not-accessible | current | This table contains the current value for the maximum number of sessions that can be supported on the CMCC card. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.2.2.1 | RowcipCardSessionsOperEntry | not-accessible | current | A list of CMCC specific Session values. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.2.2.1.1 | ColumncipCardOperMaxLlc2Sessions | read-only | current | This value indicates the current number of LLC2 sessions that can be supported on this CMCC card. If this value is zero, then the limit of LLC2 sessions on the… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.2.3 | TablecipCardSessionsStatsTable | not-accessible | current | This table contains the statistic value(s) for the maximum number of sessions that can be supported on the CMCC card. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.2.3.1 | RowcipCardSessionsStatsEntry | not-accessible | current | A list of CMCC specific Session values. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.2.3.1.1 | ColumncipCardStatsHiWaterLlc2Sessions | read-only | current | High water LLC2 sessions count per CMCC card. If cipCardOperMaxLlc2Sessions is zero (0), then this value starts at 256 Llc2 sessions and will be incremented in… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.2.3.1.2 | ColumncipCardStatsLlc2SessionAllocationErrs | read-only | current | This value represents the number of memory allocation errors that have occurred when attempting to create a new block of memory for the LLC2 session buffer poo… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.3 | NodecipCsnaConnection | |||
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.3.1 | TablecipCardCsnaConnTable | not-accessible | current | This table contains the map between VTAM (the I/O Device Address) and the CMCC LAN Adapter/Mac Address/SAP. For example: Channel Path Channel Path & Device & D… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.3.1.1 | RowcipCardCsnaConnEntry | not-accessible | current | A list of CSNA internal LAN Adapter connection values. The first three indices allow the mapping to the LAN and Adapter. To obtain the mapping to the llc SAP t… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.3.1.1.1 | ColumncipCardCsnaConnActiveSessions | read-only | current | The Active Sessions in this VTAM to CMCC LAN Adapter/Mac Address mapping. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.3.1.1.2 | ColumncipCardCsnaSlot | read-only | current | Slot number of the CMCC card that the Path and Device are configured. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.3.1.1.3 | ColumncipCardCsnaPort | read-only | current | Port number on the CMCC card that the Path and Device are configured. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.3.1.1.4 | ColumncipCardCsnaConnPath | read-only | current | Hex path identifier used by this instance of CMCC LAN adapter/SAP to connect SNA sessions to VTAM. For more information see the textual convention ChannelPath. |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.1.3.1.1.5 | ColumncipCardCsnaConnDevice | read-only | current | Two digit hex device address used by this CMCC LAN adapter/SAP instance to connect SNA sessions to VTAM. For more information see the textual convention Channe… |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.2 | NodecipCsnaNotificationPrefix | |||
| 1.3.6.1.4.1.9.9.20.1.3.1.1.2.0 | NodecipCsnaNotifications | |||
| 1.3.6.1.4.1.9.9.20.1.3.1.1.2.0.1 | NotificationcipCsnaOpenDuplicateSapFailure | current | This trap indicates that VTAM attempted to open a SAP that was already open via another Path/Device on this CMCC card. | |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.2.0.2 | NotificationcipCsnaLlc2ConnectionLimitExceeded | current | This trap indicates that a connection attempt was rejected due to a connection resource limitation | |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.3 | NodeciscoCipCsnaMibConformance | |||
| 1.3.6.1.4.1.9.9.20.1.3.1.1.3.1 | NodeciscoCipCsnaMibCompliances | |||
| 1.3.6.1.4.1.9.9.20.1.3.1.1.3.1.1 | ComplianceciscoCipCsnaMibCompliance | current | The compliance statement for the Channel Systems Network Architecture (CSNA) feature. | |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.3.2 | NodeciscoCipCsnaMibGroups | |||
| 1.3.6.1.4.1.9.9.20.1.3.1.1.3.2.1 | GroupciscoCsnaGroup | current | A collection of objects providing (Channel Systems Network Architecture (CSNA) Administration, Operational status and Statistics. | |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.3.2.2 | GroupciscoMaxSessionsGroup | current | A collection of objects providing the information on the maximum number of sessions supported on a CMCC card. | |
| 1.3.6.1.4.1.9.9.20.1.3.1.1.3.2.3 | GroupciscoCsnaConnGroup | current | A collection of objects providing CMCC LAN adapter/SAP connection mapping to the Path/Device (subchannel). |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| ChannelDevice | OCTET STRING(SIZE (0..2)) | current | Two octet hex device address for the device the Systems Network Architecture (SNA) host will use to communicate with the Channel Systems Network Architecture (CSNA) feature on the CMCC card. The first octet will always … |
| ChannelPath | OCTET STRING(SIZE (0..2)) | current | This channel path is a two octet value made up of the following values: Path 01-FF For a directly attached ESCON channel or any parallel channel, this value is 01 unless the system administrator has configured another v… |