CISCO-CNO-SWITCH-MIB
41 objects
The MIB module for the management of Cisco Network Office (CNO) switch products.
Imported Objects
| CISCO-SMI | ciscoExperiment |
| RFC1213-MIB | ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.10.43 | IdentityciscoCNOSwitchMIB | The MIB module for the management of Cisco Network Office (CNO) switch products. | ||
| 1.3.6.1.4.1.9.10.43.1 | NodeciscoCNOSwitchMIBObjects | |||
| 1.3.6.1.4.1.9.10.43.1.1 | NodecnosSysInfo | |||
| 1.3.6.1.4.1.9.10.43.1.1.1 | ScalarcnosSysInfoSerialNo | read-only | current | Serial number of the hardware. |
| 1.3.6.1.4.1.9.10.43.1.1.2 | ScalarcnosSysInfoBoardRevision | read-only | current | Returns the revision number of the switch main board on which the system firmware resides. |
| 1.3.6.1.4.1.9.10.43.1.1.3 | ScalarcnosSysInfoBootVersion | read-only | current | Returns the version number of the switch boot S/W residing in flash. The format is 'V1.2.3'. |
| 1.3.6.1.4.1.9.10.43.1.1.4 | ScalarcnosSysInfoAddrCapacity | read-only | current | The system-wide maximum number of addresses supported. |
| 1.3.6.1.4.1.9.10.43.1.2 | NodecnosSysConfig | |||
| 1.3.6.1.4.1.9.10.43.1.2.1 | ScalarcnosSysConfigReset | read-write | current | Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). Setting this object to n… |
| 1.3.6.1.4.1.9.10.43.1.2.2 | ScalarcnosSysConfigDefaultReset | read-write | current | Setting this object to reset(2) causes a complete reset of both hardware and software, but does not run the POST (Power On Self Test). All configuration parame… |
| 1.3.6.1.4.1.9.10.43.1.2.3 | ScalarcnosSysConfigMonitor | read-write | current | Selects whether frames to/from certain ports are sent to conSwitchSysConfigMonitorPort. A port is selected for monitoring purpose when its cnosPortMonitoring o… |
| 1.3.6.1.4.1.9.10.43.1.2.4 | ScalarcnosSysConfigMonitorPort | read-write | current | Port number to which all frames to/from monitored ports are sent. Frames are only monitored if the sysConfigMonitor object is set to enabled(1). A number from … |
| 1.3.6.1.4.1.9.10.43.1.3 | NodecnosPort | |||
| 1.3.6.1.4.1.9.10.43.1.3.1 | TablecnosPortTable | not-accessible | current | A list of configuration entries for individually switched ports. There in one entry created automatically for each switch port (ifType of ethernetCsmacd) on th… |
| 1.3.6.1.4.1.9.10.43.1.3.1.1 | RowcnosPortEntry | not-accessible | current | Configuration parameters for an individually switched port. |
| 1.3.6.1.4.1.9.10.43.1.3.1.1.1 | ColumncnosPortControllerRevision | read-only | current | Returns the revision number of the port controller. |
| 1.3.6.1.4.1.9.10.43.1.3.1.1.2 | ColumncnosPortName | read-write | current | A descriptive string of up to 80 characters used by the network administrator to name a port. |
| 1.3.6.1.4.1.9.10.43.1.3.1.1.3 | ColumncnosPortDuplexAdmin | read-write | current | Set to fullDuplex(1) to operate in full duplex mode: port will allow simultaneous transmit and receive which can double its bandwidth. Set to halfDuplex(2) to … |
| 1.3.6.1.4.1.9.10.43.1.3.1.1.4 | ColumncnosPortDuplexStatus | read-only | current | The operating duplex mode of the switched port. |
| 1.3.6.1.4.1.9.10.43.1.3.1.1.5 | ColumncnosPortSpeedAdmin | read-write | current | Set to tenMbps(1) to operate in 10Mbps speed mode. Set to oneHundredMbps(2) to operate in 100Mbps speed mode. Set to autoNegotiate(3) to allow the switch to ne… |
| 1.3.6.1.4.1.9.10.43.1.3.1.1.6 | ColumncnosPortSpeedStatus | read-only | current | The operating speed of the switched port. |
| 1.3.6.1.4.1.9.10.43.1.3.1.1.7 | ColumncnosPortMonitoring | read-write | current | Set to enabled(1) to forward receive and transmit frames on this port to the port identified by cnosSysConfigMonitorPort. Set to disabled(2) to not monitor fra… |
| 1.3.6.1.4.1.9.10.43.1.3.1.1.8 | ColumncnosPortLinkStatus | read-only | current | The current port link status. |
| 1.3.6.1.4.1.9.10.43.1.3.1.1.9 | ColumncnosPortSTPPortFastMode | read-write | current | This object configures the port into the Spanning Tree port-fast mode. When enabled(1), the STP can transition the port's state directly from blocking to forwa… |
| 1.3.6.1.4.1.9.10.43.1.3.1.1.10 | ColumncnosPortVlanMember | read-write | current | Set the port to be a member of a specified VLAN. Set the port to all(5) to be shared among all VLANs. |
| 1.3.6.1.4.1.9.10.43.1.4 | NodecnosVlan | |||
| 1.3.6.1.4.1.9.10.43.1.4.1 | TablecnosVlanTable | not-accessible | current | Table containing a list of VLANs. |
| 1.3.6.1.4.1.9.10.43.1.4.1.1 | RowcnosVlanEntry | not-accessible | current | Information pertaining to a VLAN. |
| 1.3.6.1.4.1.9.10.43.1.4.1.1.1 | ColumncnosVlanIndex | not-accessible | current | Identification of a VLAN entry. |
| 1.3.6.1.4.1.9.10.43.1.4.1.1.2 | ColumncnosVlanSTPState | read-write | current | The switch implements the 802.1d Spanning Tree Algorithm & Protocol (STP) on all its port to detect loops in the bridge topology. The user may, for any reason,… |
| 1.3.6.1.4.1.9.10.43.2 | NodeciscoCNOSwitchNotifications | |||
| 1.3.6.1.4.1.9.10.43.2.0 | NodeciscoCNOSwitchNotificationsPrefix | |||
| 1.3.6.1.4.1.9.10.43.3 | NodeciscoCNOSwitchMIBComformance | |||
| 1.3.6.1.4.1.9.10.43.3.1 | NodeciscoCNOSwitchMIBCompliances | |||
| 1.3.6.1.4.1.9.10.43.3.1.1 | ComplianceciscoCNOSwitchCompliance | current | The compliance statement for the Cisco CNO switch products. | |
| 1.3.6.1.4.1.9.10.43.3.2 | NodeciscoCNOSwitchMIBGroups | |||
| 1.3.6.1.4.1.9.10.43.3.2.1 | GroupciscoCNOSwitchSysInfoGroup | current | A collection of the system information objects for use with the Cisco CNO switch products. | |
| 1.3.6.1.4.1.9.10.43.3.2.2 | GroupciscoCNOSwitchConfigGroup | current | A collection of the system configuration objects for use with the Cisco CNO switch products. | |
| 1.3.6.1.4.1.9.10.43.3.2.3 | GroupciscoCNOSwitchPortGroup | current | A collection of the the switched port objects for use with the Cisco CNO switch products. | |
| 1.3.6.1.4.1.9.10.43.3.2.4 | GroupciscoCNOSwitchMonitorPortGroup | current | A collection of the switched port monitoring objects for use with the Cisco CNO switch products. | |
| 1.3.6.1.4.1.9.10.43.3.2.5 | GroupciscoCNOSwitchVlanGroup | current | A collection of the VLAN objects for use with the Cisco CNO switch products. |