CISCO-DSP-MGMT-MIB
165 objects
Digital Signal Processing (DSP) Management MIB module. The MIB module monitors the DSP resource and status. Acronyms & Terms ================ DTMF - Dual Tone Multi-Frequency. DTMF uses two frequencies, the high frequency omponent and the low frequency component, to generate digit signals. DSPFarm - DSPFarm ia a logical name given to a functionality which groups the DSP resources to provide certain service like transcoding and conferencing using DSP. DSPFarm profile - A DSPFarm profile logically groups the DSP to perform service like transcoding and conferencing. It is uniquely identified by a profile number. MTP - Media Termination Point. RTP packet received by MTP in the incoming call leg will be regenerated and send out through the outgoing call leg. transcode - Translating codec. transcoder is used to do codec translation. If incoming call leg negotiates codec-A and outgoing call leg negotiates codec-B then transcoder will convert received RTP packet from codec-A to codec-B or codec-B to codec-A. MTP hardware session - Media termination functionality with using DSP. MTP software session - Media termination functionality without using DSP. RTP - Real-time Transport protocol. Video Pool - A group of DSP resources dedicated to providing video services.
Imported Objects
| CISCO-QOS-PIB-MIB | Percent |
| CISCO-SMI | ciscoMgmt |
| ENTITY-MIB | entPhysicalIndex entPhysicalName |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus StorageType TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.86 | IdentityciscoDspMgmtMIB | Digital Signal Processing (DSP) Management MIB module. The MIB module monitors the DSP resource and status. Acronyms & Terms ================ DTMF - Dual Tone … | ||
| 1.3.6.1.4.1.9.9.86.0 | NodecdspMgmtNotifications | |||
| 1.3.6.1.4.1.9.9.86.1 | NodecdspMgmtObjects | |||
| 1.3.6.1.4.1.9.9.86.1.1 | NodecdspCardObjects | |||
| 1.3.6.1.4.1.9.9.86.1.1.1 | TablecdspCardStatusTable | not-accessible | current | The DSP Card Table. It contains status information of the DSP cards present within the router. |
| 1.3.6.1.4.1.9.9.86.1.1.1.1 | RowcdspCardStatusEntry | not-accessible | current | An entry in the DSP card table indicates the DSP card state, resource utilization. Each entry is created when a DSP software is detected on a DSP card. The ent… |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.1 | ColumncdspCardIndex | read-only | current | The object corresponds to cardIndex in the chassis mib. If value of this object is 0, then the entry is not associated to cardIndex of the chassis mib. |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.2 | ColumncdspCardState | read-only | current | The object indicates the current state of DSP card being monitored. normal - DSP card in normal condition. warning - DSP card has some problem and need attenti… |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.3 | ColumncdspCardResourceUtilization | read-only | current | The object indicates the percentage of current DSP resource utilization of the card. The utilization is a ratio of number of busy DSP resources (for handling c… |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.4 | ColumncdspCardLastHiWaterUtilization | read-only | current | The object indicates the last high water mark of DSP resource utilization. This object is reset to 0 after DSP card is reset. |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.5 | ColumncdspCardLastResetTime | read-only | current | The value of sysUpTime when the last DSP card reset occurred. |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.6 | ColumncdspCardMaxChanPerDSP | read-only | current | The maximum number of channels allowed in each DSP. The value is chosen in an implementation-dependent manner by the DSP functionality. The value of 0 in this … |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.7 | ColumncdspTotalDsp | read-only | current | The total number of DSPs in the card. |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.8 | ColumncdspFailedDsp | read-only | current | The number of DSPs in the failed state (i.e cdspOperstate is 'failed') |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.9 | ColumncdspDspSwitchOverThreshold | read-write | current | This object specifies the threshold of DSP failures. When 'cdspFailedDsp' reaches the value of this object, the voice gateway switchover will occur. The maximu… |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.10 | ColumncdspCongestedDsp | read-only | current | The number of DSPs in the congested state (i.e cdspOperstate is 'congested'). |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.11 | ColumncdspNormalDsp | read-only | current | The number of DSPs in the normal state (i.e cdspOperstate is 'normal'). |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.12 | ColumncdspNx64Dsp | read-write | current | This object specifies the number of DSPs that need to be set aside for making Nx64 calls. The max value of this object is limited to the value of the object 'c… |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.13 | ColumncdspCodecTemplateSupported | read-only | current | This object indicates the codec template supported in DSP image. The codec template can be: tgw - Codec template for wireline used in Trunking GateWay applicat… |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.14 | ColumncdspCardVideoPoolUtilization | read-only | current | The object indicates the percentage of current DSP video resource pool utilization of the card. |
| 1.3.6.1.4.1.9.9.86.1.1.1.1.15 | ColumncdspCardVideoPoolUtilizationThreshold | read-write | current | This object specifies the threshold of DSP video pool resource usage. When cdspCardVideoPoolUtilization crosses the value of this threshold in the rising direc… |
| 1.3.6.1.4.1.9.9.86.1.2 | NodecdspObjects | |||
| 1.3.6.1.4.1.9.9.86.1.2.1 | TablecdspStatusTable | not-accessible | current | Status information for the DSPs. This status table is used for tracking dangling DSP resources. The dangling DSP channel means that the DSP channel is reserved… |
| 1.3.6.1.4.1.9.9.86.1.2.1.1 | RowcdspStatusEntry | not-accessible | current | An entry in cdspStatusTable indicates the DSP state and alarm conditions. Each entry is created when a DSP is detected on a DSP card. The entry is deleted when… |
| 1.3.6.1.4.1.9.9.86.1.2.1.1.1 | ColumncdspOperState | read-only | current | The current operational state of the DSP. normal - DSP operates normally shutdown - DSP is shutdown due to fatal error congested - DSP does not accept call bec… |
| 1.3.6.1.4.1.9.9.86.1.2.1.1.2 | ColumncdspAlarms | read-only | current | The object indicates the accumulated number of DSP Alarms. |
| 1.3.6.1.4.1.9.9.86.1.2.1.1.3 | ColumncdspLastAlarmCause | read-only | current | The object indicates the current or last alarm state of DSP. other - none of the following noAlarm - alarm condition had not been detected dspFatalError - DSP … |
| 1.3.6.1.4.1.9.9.86.1.2.1.1.4 | ColumncdspLastAlarmCauseText | read-only | current | The object indicates the failure reason for the current or last DSP Alarm. It should be used only for direct, human-readable display and only if a management s… |
| 1.3.6.1.4.1.9.9.86.1.2.1.1.5 | ColumncdspLastAlarmTime | read-only | current | The value of sysUpTime when the last DSP Alarm occurred. The value of this object is 0 if the value of cdspLastAlarmCause object is 'noAlarm'. |
| 1.3.6.1.4.1.9.9.86.1.2.1.1.6 | ColumncdspTotalChannels | read-only | current | The total number of channels in the DSP. This value is predetermined by the DSP functionality upon initialization. The value of 0 in this object indicates Chan… |
| 1.3.6.1.4.1.9.9.86.1.2.1.1.7 | ColumncdspInUseChannels | read-only | current | The number of channels that are reserved for serving calls. The value is incremented when the DSP channel is reserved for call setup and is decremented after t… |
| 1.3.6.1.4.1.9.9.86.1.2.1.1.8 | ColumncdspActiveChannels | read-only | current | The number of channels that are used by active calls to process media stream. The value is incremented after the reserved DSP channel enters call connection st… |
| 1.3.6.1.4.1.9.9.86.1.2.1.1.9 | ColumncdspSigBearerChannelSplit | read-only | current | This object indicates if the DSP channels are splitted for signaling call and bearer call. If the value of this object is 'true' which means that signaling cal… |
| 1.3.6.1.4.1.9.9.86.1.2.1.1.10 | ColumncdspNumCongestionOccurrence | read-only | current | The number of congestion occurred on the DSP. This value is set to 0 when system is reset. |
| 1.3.6.1.4.1.9.9.86.1.2.1.1.11 | ColumncdspDspNum | read-only | current | This object identifies the DSP number associated with this DSP entity. |
| 1.3.6.1.4.1.9.9.86.1.2.2 | TablecdspStatusXTable | not-accessible | current | This table provides the additional detailed state and statistics information for a DSP that supports the splitted signalling and bearer channels. |
| 1.3.6.1.4.1.9.9.86.1.2.2.1 | RowcdspStatusXEntry | not-accessible | current | An entry of this table is created when its associated entry in cdspStatusTable is created and the value of cdspSigBearerChannelSplit object is 'true'. |
| 1.3.6.1.4.1.9.9.86.1.2.2.1.1 | ColumncdspXNumberOfBearerCalls | read-only | current | The current number of bearer calls on the DSP. |
| 1.3.6.1.4.1.9.9.86.1.2.2.1.2 | ColumncdspXNumberOfSigCalls | read-only | current | The current number of signaling calls on the DSP. |
| 1.3.6.1.4.1.9.9.86.1.2.2.1.3 | ColumncdspXAvailableBearerBandwidth | read-only | current | The percentage of channels on the DSP currently available for bearer calls. |
| 1.3.6.1.4.1.9.9.86.1.2.2.1.4 | ColumncdspXAvailableSigBandwidth | read-only | current | The percentage of channels on the DSP currently available for signaling calls. |
| 1.3.6.1.4.1.9.9.86.1.3 | NodecdspMIBNotificationEnables | |||
| 1.3.6.1.4.1.9.9.86.1.3.1 | ScalarcdspMIBEnableCardStatusNotification | read-write | current | This variable controls whether the system produces the cdspMIBCardStateNotification. A false value will prevent DSP card fatal notifications from being generat… |
| 1.3.6.1.4.1.9.9.86.1.3.2 | ScalarcdspEnableOperStateNotification | read-write | current | This variable controls whether the system produces the cdspOperStateNotification. A false value will prevent a DSP operational state notification from being ge… |
| 1.3.6.1.4.1.9.9.86.1.3.3 | ScalarcdspVideoUsageNotificationEnable | read-write | current | This object specifies whether the system produces cdspVideoUsageNotification. 'true': Video usage notification is generated by this system. 'false': Video usag… |
| 1.3.6.1.4.1.9.9.86.1.3.4 | ScalarcdspVideoOutOfResourceNotificationEnable | read-write | current | This object specifies whether the system produces cdspVideoOutOfResourceNotification. 'true': Video out-of-resource notification is generated by this system. '… |
| 1.3.6.1.4.1.9.9.86.1.4 | NodecdspVoiceObjects | |||
| 1.3.6.1.4.1.9.9.86.1.4.1 | TablecdspVoiceParamTable | not-accessible | current | This table contains information on voice call setup related parameters for DSP resource. |
| 1.3.6.1.4.1.9.9.86.1.4.1.1 | RowcdspVoiceParamEntry | not-accessible | current | An entry in the DSP table contains information regarding a single DSP resource associated voice call setup parameters. An entry in this table is created when a… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.1 | ColumncdspRtpSidPayloadType | read-write | current | This object specifies the RTP (Real Time Protocol) payload type of the SID (Silence Insertion Descriptor) packet that is sent to the remote endpoint at the ons… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.2 | ColumncdspRtcpControl | read-write | current | This objects controls if RTCP (Real Time Control Protocol) will be enabled. If this object is set to 'true', both transmission and reception of RTCP packets ar… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.3 | ColumncdspRtcpTransInterval | read-write | current | This attribute specifies the RTCP report interval (defined in RFC1889). It indicates the interval in which the RTCP reports should be sent to the participating… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.4 | ColumncdspRtcpRecvMultiplier | read-write | current | This object specifies an approximate RTCP report interval (defined in RFC 1889) in milliseconds in which the RTCP reports should be sent to the participating m… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.5 | ColumncdspVadAdaptive | read-write | current | This attribute is used to enable or disable the Adaptive VAD knob of the VAD algorithm. Adaptive VAD works in conjunction with VAD Threshold (cvifcfgMusicOnHol… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.6 | ColumncdspDtmfPowerLevel | read-write | current | This object specifies the power level of the low frequency component of DTMF. The power level of the high frequency component of DTMF is relative above or belo… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.7 | ColumncdspDtmfPowerTwist | read-write | current | This object specifies the relative power level of the high frequency component of DTMF. The low frequency group is always fixed to the value specified by cdspD… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.8 | ColumncdspRtcpTimerControl | read-write | current | This object specifies when the RTCP receive timer is started. disabled - timer is disabled startImmediately - timer starts immediately as soon as RTCP is enabl… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.9 | ColumncdspVqmControl | read-write | current | This object is used to disable VQM or enable either RFC 3611 RTCPXR or Extended Network Quality Metrics VQM. disable - VQM is disabled. rfc3611Vqm - RFC 3611 R… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.10 | ColumncdspRtcpXrControl | read-write | current | This object controls if RTCPXR (Real Time Control Protocol Extended Report) is enabled. If this object is set to 'true', both transmission and reception of RTC… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.11 | ColumncdspRtcpXrTransMultiplier | read-write | current | This object is used to configure the RTCPXR report frequency. i.e. how many RTCP packets during the interval of every RTCPXR packet. The RTCPXR report is sent … |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.12 | ColumncdspRtcpXrGminDefault | read-write | current | This object is the default minimum gap value configured for the IP stream. This object is applicable only if 'cdspVqmControl' is set to 'rfc3611Vqm'. |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.13 | ColumncdspRtcpXrExtRfactor | read-write | current | This object is the external R factor metric value. The value 127 means it is not applicable. This object is applicable only if 'cdspVqmControl' is set to 'rfc3… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.14 | ColumncdspPktLossConcealment | read-write | current | This object specifies the packet loss concealment: (1) none: No packet loss concealment applied (2) simple: Cisco Proprietary packet loss concealment (3) g711A… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.15 | ColumncdspVqmThreshSES | read-write | current | This attribute specifies the threshold for Severely Errored Second on VQM. If the total number of milliseconds sampled as bad voice quality in one second perio… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.16 | ColumncdspTransparentIpIp | read-write | deprecated | This attribute is used to enable or disable the transparent mode when establishing a non-transcoding IP-IP connection. The attribute does not apply for the tra… |
| 1.3.6.1.4.1.9.9.86.1.4.1.1.17 | ColumncdspVoiceModeIpIp | read-write | current | This object specifies the voice mode for IP IP connections. normal : A normal Mode is a transcoding mode for IP-IP connections where the bearer properties will… |
| 1.3.6.1.4.1.9.9.86.1.5 | NodecdspUtilObjects | |||
| 1.3.6.1.4.1.9.9.86.1.5.1 | TablecdspUtilTable | not-accessible | current | This table contains DSP utilization information for all the codec families available in codec template currently active on VXSM. |
| 1.3.6.1.4.1.9.9.86.1.5.1.1 | RowcdspUtilEntry | not-accessible | current | An entry (conceptual row) in cdspUtilTable indicates the DSP capacity usage. Each entry maps to a codec pool family , uniquely identified by cdspCodecPoolIndex… |
| 1.3.6.1.4.1.9.9.86.1.5.1.1.1 | ColumncdspCodecPoolIndex | not-accessible | current | This object identifies a row. Pool index is corresponding to the number of DSP channels utilized. The instance identifier value of this object depends on the c… |
| 1.3.6.1.4.1.9.9.86.1.5.1.1.2 | ColumncdspCurrentUtilCap | read-only | current | This object indicates the number of DSP channels which are currently being utilized corresponding to active calls on VXSM segregated on the basis of codec fami… |
| 1.3.6.1.4.1.9.9.86.1.5.1.1.3 | ColumncdspCurrentAvlbCap | read-only | current | This object indicates the number of DSP channels which are currently available on VXSM corresponding to a codec family. |
| 1.3.6.1.4.1.9.9.86.1.6 | NodecdspDspfarmObjects | |||
| 1.3.6.1.4.1.9.9.86.1.6.1 | ScalarcdspGlobMaxConfTranscodeSess | read-write | current | This object indicates the maximum transcode sessions configured globally for the voice gateway. |
| 1.3.6.1.4.1.9.9.86.1.6.2 | ScalarcdspGlobMaxAvailTranscodeSess | read-only | current | This object indicates the total number of available sessions from the maximum transcode sessions configured globally for the voice gateway. |
| 1.3.6.1.4.1.9.9.86.1.6.3 | TablecdspTranscodeProfileTable | not-accessible | current | This table contains information about each transcode DSPFarm profile. It gives the maximum number of transcode sessions configured and the number of available … |
| 1.3.6.1.4.1.9.9.86.1.6.3.1 | RowcdspTranscodeProfileEntry | not-accessible | current | An entry in cdspTranscodeProfileTable indicates the transcode DSPFarm profile maximum configured sessions and available sessions. Each DSPFarm transcode profil… |
| 1.3.6.1.4.1.9.9.86.1.6.3.1.1 | ColumncdspTranscodeProfileMaxCodec | read-create | current | This object indicates the maximum number of codecs to be configured in the DSPFarm transcode profile. |
| 1.3.6.1.4.1.9.9.86.1.6.3.1.2 | ColumncdspTranscodeProfileId | not-accessible | current | This object indicates the profile number of the DSPFarm transcode profile. |
| 1.3.6.1.4.1.9.9.86.1.6.3.1.3 | ColumncdspTranscodeProfileMaxConfSess | read-create | current | This object indicates the maximum transcode sessions configured on the DSPFarm transcode profile for the voice gateway. |
| 1.3.6.1.4.1.9.9.86.1.6.3.1.4 | ColumncdspTranscodeProfileMaxAvailSess | read-only | current | This object indicates the total number of available transcode sessions per transcode profile from the configured maximum transcode sessions per transcode profi… |
| 1.3.6.1.4.1.9.9.86.1.6.3.1.5 | ColumncdspTranscodeProfileRowStatus | read-create | current | This object is used to create a new entry or delete an existing entry in cdspTranscodeProfileTable. The storage type for all the entries created would be volat… |
| 1.3.6.1.4.1.9.9.86.1.6.3.1.6 | ColumncdspTranscodeResourceId | read-only | current | The object indicates resource ID in the DSPFarm transcode profile |
| 1.3.6.1.4.1.9.9.86.1.6.3.1.7 | ColumncdspTranscodeDescription | read-only | current | The object indicates description of DSPFarm transcode profile. |
| 1.3.6.1.4.1.9.9.86.1.6.3.1.8 | ColumncdspTranscodeService | read-only | current | This object indicates the profile service type of the DSPFarm transcode profile. |
| 1.3.6.1.4.1.9.9.86.1.6.3.1.9 | ColumncdspTranscodeAdminState | read-create | current | This object specifies the admin state of the DSPFarm transcode profile |
| 1.3.6.1.4.1.9.9.86.1.6.3.1.10 | ColumncdspTranscodeApplication | read-only | current | This object indicates the application used by the DSPFarm transcode profile |
| 1.3.6.1.4.1.9.9.86.1.6.3.1.11 | ColumncdspTranscodeApplicationStatus | read-only | current | The object indicates application Status of DSPFarm transcode profile. |
| 1.3.6.1.4.1.9.9.86.1.6.4 | TablecdspMtpProfileTable | not-accessible | current | This table contains information about each MTP DSPFarm profile. It gives the maximum number of MTP sessions configured and the number of available sessions per… |
| 1.3.6.1.4.1.9.9.86.1.6.4.1 | RowcdspMtpProfileEntry | not-accessible | current | An entry in cdspMtpProfileTable indicates the MTP DSPFarm profile maximum configured sessions and available sessions. Each DSPFarm MTP profile configured in th… |
| 1.3.6.1.4.1.9.9.86.1.6.4.1.1 | ColumncdspMtpProfileId | not-accessible | current | This object indicates the profile number of the DSPFarm MTP profile. |
| 1.3.6.1.4.1.9.9.86.1.6.4.1.2 | ColumncdspMtpProfileMaxConfSoftSess | read-create | current | This object indicates the maximum MTP software sessions configured per DSPFarm MTP profile for the voice gateway. |
| 1.3.6.1.4.1.9.9.86.1.6.4.1.3 | ColumncdspMtpProfileMaxConfHardSess | read-create | current | This object indicates the maximum MTP hardware sessions configured per DSPFarm MTP profile for the voice gateway. |
| 1.3.6.1.4.1.9.9.86.1.6.4.1.4 | ColumncdspMtpProfileMaxAvailHardSess | read-only | current | This object indicates the total number of available MTP Hardware sessions per MTP profile from the configured maximum MTP sessions per MTP profile for the voic… |
| 1.3.6.1.4.1.9.9.86.1.6.4.1.5 | ColumncdspMtpProfileRowStatus | read-create | current | This object is used to create a new entry or delete an existing entry in cdspMtpProfileTable. The storage type for all the entries created would be volatile. T… |
| 1.3.6.1.4.1.9.9.86.1.6.4.1.6 | ColumncdspMtpResourceId | read-only | current | The object indicates resource ID in the DSPFarm MTP profile |
| 1.3.6.1.4.1.9.9.86.1.6.4.1.7 | ColumncdspMtpDescription | read-only | current | The object indicates description of DSPFarm MTP profile. |
| 1.3.6.1.4.1.9.9.86.1.6.4.1.8 | ColumncdspMtpService | read-only | current | This object indicates the profile service type of the DSPFarm Mtp profile. |
| 1.3.6.1.4.1.9.9.86.1.6.4.1.9 | ColumncdspMtpAdminState | read-create | current | This object specifies the admin state of the DSPFarm MTP profile |
| 1.3.6.1.4.1.9.9.86.1.6.4.1.10 | ColumncdspMtpApplication | read-only | current | This object indicates the Application used by the DSPFarm MTP profile |
| 1.3.6.1.4.1.9.9.86.1.6.4.1.11 | ColumncdspMtpApplicationStatus | read-only | current | The object indicates application Status of DSPFarm MTP profile. |
| 1.3.6.1.4.1.9.9.86.1.6.4.1.12 | ColumncdspMtpProfileMaxCodec | read-only | current | This object specifies maximum number of codecs to be configured in the DSPFarm MTP profile. |
| 1.3.6.1.4.1.9.9.86.1.6.4.1.13 | ColumncdspMtpProfileMaxAvailSoftSess | read-only | current | This object indicates the total number of available MTP Software sessions per MTP profile from the configured maximum MTP sessions per MTP profile for the voic… |
| 1.3.6.1.4.1.9.9.86.1.6.5 | TablecdspConferenceProfileTable | not-accessible | current | This table contains information about each conference DSPFarm profile. It gives the maximum number of conference sessions configured and the number of availabl… |
| 1.3.6.1.4.1.9.9.86.1.6.5.1 | RowcdspConferenceProfileEntry | not-accessible | current | An entry in cdspConferenceProfileTable indicates the conference DSPFarm profile maximum configured sessions and available sessions. Each DSPFarm conference pro… |
| 1.3.6.1.4.1.9.9.86.1.6.5.1.1 | ColumncdspConferenceProfileId | not-accessible | current | This object indicates the profile number of the DSPFarm conference profile. |
| 1.3.6.1.4.1.9.9.86.1.6.5.1.2 | ColumncdspConferenceResourceId | read-only | current | The object indicates resource ID in the DSPFarm conference profile. |
| 1.3.6.1.4.1.9.9.86.1.6.5.1.3 | ColumncdspConferenceDescription | read-only | current | The object indicates description of DSPFarm conference profile. |
| 1.3.6.1.4.1.9.9.86.1.6.5.1.4 | ColumncdspConferenceService | read-only | current | This object indicates the profile service type of the DSPFarm conference profile. |
| 1.3.6.1.4.1.9.9.86.1.6.5.1.5 | ColumncdspConferenceAdminState | read-create | current | This object specifies the admin state of the DSPFarm conference profile. |
| 1.3.6.1.4.1.9.9.86.1.6.5.1.6 | ColumncdspConferenceApplication | read-only | current | This object indicates the application used by the DSPFarm conference profile. |
| 1.3.6.1.4.1.9.9.86.1.6.5.1.7 | ColumncdspConferenceApplicationStatus | read-only | current | The object indicates application Status of DSPFarm conference profile. |
| 1.3.6.1.4.1.9.9.86.1.6.5.1.8 | ColumncdspConferenceProfileMaxCodec | read-only | current | This object specifies maximum number of codecs to be configured in the DSPFarm conference profile. |
| 1.3.6.1.4.1.9.9.86.1.6.5.1.9 | ColumncdspConferenceProfileMaxConfSess | read-create | current | This object specifies the maximum conference sessions configured on the DSPFarm conference profile for the voice gateway. |
| 1.3.6.1.4.1.9.9.86.1.6.5.1.10 | ColumncdspConferenceProfileMaxAvailSess | read-only | current | This object indicates the total number of available conference sessions per conference profile from the configured maximum conference sessions per conference p… |
| 1.3.6.1.4.1.9.9.86.1.6.5.1.11 | ColumncdspConferenceProfileStorageType | read-only | current | The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. |
| 1.3.6.1.4.1.9.9.86.1.6.5.1.12 | ColumncdspConferenceProfileRowStatus | read-create | current | This object is used to create a new entry or delete an existing entry in cdspConferenceProfileTable. The storage type for all the entries created would be vola… |
| 1.3.6.1.4.1.9.9.86.1.7 | NodecdspDspfarmUtilObjects | |||
| 1.3.6.1.4.1.9.9.86.1.7.1 | ScalarcdspTotAvailTranscodeSess | read-only | current | This object indicates the total number of transcode sessions available for the voice gateway. The value is equal to summation of all the values returned by tra… |
| 1.3.6.1.4.1.9.9.86.1.7.2 | ScalarcdspTotUnusedTranscodeSess | read-only | current | This object indicates the total number of unused transcode sessions. |
| 1.3.6.1.4.1.9.9.86.1.7.3 | ScalarcdspTotAvailMtpSess | read-only | current | This object indicates the total number of MTP sessions available for the voice gateway. The value is equal to summation of all the values returned by MTP profi… |
| 1.3.6.1.4.1.9.9.86.1.7.4 | ScalarcdspTotUnusedMtpSess | read-only | current | This object indicates the total number of unused MTP sessions. |
| 1.3.6.1.4.1.9.9.86.2 | NodecdspMIBNotificationPrefix | |||
| 1.3.6.1.4.1.9.9.86.2.0 | NodecdspMIBNotifications | |||
| 1.3.6.1.4.1.9.9.86.2.0.1 | NotificationcdspMIBCardStateNotification | current | A cdspMIBCardStateNotification is sent when the cdspCardState enters into normal(1) state and enters into or exits from fatal(4) state. | |
| 1.3.6.1.4.1.9.9.86.2.0.2 | NotificationcdspOperStateNotification | current | A cdspOperStateNotification is sent when the cdspOperState enters into normal(1) state or shutdown(2) state. The value of entPhysicalName contains the name of … | |
| 1.3.6.1.4.1.9.9.86.2.0.3 | NotificationcdspVideoUsageNotification | current | This notification is sent when cdspCardVideoPoolUtilization reaches the specified threshold (cdspCardVideoPoolUtilizationThreshold). cdspCardVideoPoolUtilizati… | |
| 1.3.6.1.4.1.9.9.86.2.0.4 | NotificationcdspVideoOutOfResourceNotification | current | A cdspVideoOutOfResourceNotification is sent when there is not enough DSP resource in the video pool of the system for video services. cdspCardVideoPoolUtiliza… | |
| 1.3.6.1.4.1.9.9.86.3 | NodecdspMgmtConformance | |||
| 1.3.6.1.4.1.9.9.86.3.1 | NodecdspMgmtCompliances | |||
| 1.3.6.1.4.1.9.9.86.3.1.1 | CompliancecdspMgmtCompliance | deprecated | The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. | |
| 1.3.6.1.4.1.9.9.86.3.1.2 | CompliancecdspMgmtComplianceRev1 | deprecated | The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. | |
| 1.3.6.1.4.1.9.9.86.3.1.3 | CompliancecdspMgmtComplianceRev2 | deprecated | The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. | |
| 1.3.6.1.4.1.9.9.86.3.1.4 | CompliancecdspMgmtComplianceRev3 | deprecated | The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. | |
| 1.3.6.1.4.1.9.9.86.3.1.5 | CompliancecdspMgmtComplianceRev4 | deprecated | The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. This replaces cdspMgmtComplianceRev3. | |
| 1.3.6.1.4.1.9.9.86.3.1.6 | CompliancecdspMgmtComplianceRev5 | deprecated | The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. This replaces cdspMgmtComplianceRev4. | |
| 1.3.6.1.4.1.9.9.86.3.1.7 | CompliancecdspMgmtComplianceRev6 | deprecated | The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. This replaces cdspMgmtComplianceRev5. | |
| 1.3.6.1.4.1.9.9.86.3.1.8 | CompliancecdspMgmtComplianceRev7 | deprecated | The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. This replaces cdspMgmtComplianceRev5. | |
| 1.3.6.1.4.1.9.9.86.3.1.9 | CompliancecdspMgmtComplianceRev8 | deprecated | The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. | |
| 1.3.6.1.4.1.9.9.86.3.1.10 | CompliancecdspMgmtComplianceRev9 | deprecated | The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. | |
| 1.3.6.1.4.1.9.9.86.3.1.11 | CompliancecdspMgmtComplianceRev10 | deprecated | The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. | |
| 1.3.6.1.4.1.9.9.86.3.1.12 | CompliancecdspMgmtComplianceRev11 | read-only | deprecated | The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. |
| 1.3.6.1.4.1.9.9.86.3.1.13 | CompliancecdspMgmtComplianceRev12 | read-only | current | The compliance statement for systems that contain a Cisco DSP card and its associated DSPs. |
| 1.3.6.1.4.1.9.9.86.3.2 | NodecdspMgmtGroups | |||
| 1.3.6.1.4.1.9.9.86.3.2.1 | GroupcdspMgmtGeneralInfoGroup | deprecated | A collection of objects providing the Digital Signal Processing related information. | |
| 1.3.6.1.4.1.9.9.86.3.2.2 | GroupcdspChannelGroup | current | A collection of objects providing information specific for multiple channels per DSP. | |
| 1.3.6.1.4.1.9.9.86.3.2.3 | GroupcdspMgmtExtGeneralInfoGroup | deprecated | A collection of objects providing information for DSP. | |
| 1.3.6.1.4.1.9.9.86.3.2.4 | GroupcdspVoiceInfoGroup | deprecated | A collection of objects providing DSP voice application parameters. | |
| 1.3.6.1.4.1.9.9.86.3.2.5 | GroupcdspMgmtNotificationsGroup | deprecated | The notifications which a DSP Management entity is required to implement. | |
| 1.3.6.1.4.1.9.9.86.3.2.6 | GroupcdspChannelExtGroup | current | A collection of objects providing DSP channels splitting information. | |
| 1.3.6.1.4.1.9.9.86.3.2.7 | GroupcdspVoiceInfoGroupRev1 | deprecated | A collection of objects providing DSP voice application parameters. | |
| 1.3.6.1.4.1.9.9.86.3.2.8 | GroupcdspMgmtExtGeneralInfoGroupRev1 | current | This group replaces cdspMgmtExtGeneralInfoGroup. A collection of objects providing information for DSP. | |
| 1.3.6.1.4.1.9.9.86.3.2.9 | GroupcdspMgmtGeneralInfoGroupRev1 | current | A collection of objects providing the Digital Signal Processing related information. | |
| 1.3.6.1.4.1.9.9.86.3.2.10 | GroupcdspMgmtNotificationsGroupRev1 | current | The notifications which a DSP Management entity is required to implement. | |
| 1.3.6.1.4.1.9.9.86.3.2.11 | GroupcdspVQMGroup | current | This group includs VQM (Voice Quality Monitor) related information. It is mandatory only if VQM is supported. | |
| 1.3.6.1.4.1.9.9.86.3.2.12 | GroupcdspVoiceInfoGroupRev2 | current | A collection of objects providing DSP voice application parameters. | |
| 1.3.6.1.4.1.9.9.86.3.2.13 | GroupcdspTransCodingGroup | deprecated | A collection of objects providing DSP transcoding related parameters. | |
| 1.3.6.1.4.1.9.9.86.3.2.14 | GroupcdspTransCodingGroup1 | current | A collection of objects providing DSP transcoding related parameters for voice. | |
| 1.3.6.1.4.1.9.9.86.3.2.15 | GroupcdspUtilInfoGroup | current | A collection of objects providing DSP codec capacity usage . | |
| 1.3.6.1.4.1.9.9.86.3.2.16 | GroupcdspDspfarmInfoGroup | current | A collection of objects providing DSPFarm session configuration, availability and utilization. | |
| 1.3.6.1.4.1.9.9.86.3.2.17 | GroupcdspMgmtVideoNotificationsGroup | current | A collection of notifications related to DSP video resource. | |
| 1.3.6.1.4.1.9.9.86.3.2.18 | GroupcdspMgmtVideoInfoGroup | current | A collection of objects related to DSP video resource. | |
| 1.3.6.1.4.1.9.9.86.3.2.19 | GroupcdspTranscodeProfileGroup | current | This group provides DSPFarm Transcode session related parameters. | |
| 1.3.6.1.4.1.9.9.86.3.2.20 | GroupcdspMtpProfileGroup | current | This group provides DSPFarm MTP session related parameters. | |
| 1.3.6.1.4.1.9.9.86.3.2.21 | GroupcdspConferenceProfileGroup | current | This group provides DSPFarm conference session related parameters. |