CISCO-FIBRECHANNEL-MIB
118 objects
This MIB module defines the managed objects for physical layer characteristics of Fibre Channel interfaces and performance statistics objects for protocol specific counters in Fibre Channel devices. Performance monitoring (PM) parameters are used by service providers to gather, store, set thresholds for and report performance data for early detection of problems. Thresholds are used to set error levels for each PM parameter. During the accumulation cycle, if the current value of a performance monitoring parameter reaches or exceeds its corresponding threshold value, a threshold crossing alarm (TCA) is generated. The TCAs provide early detection of performance degradation.
Imported Objects
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifIndex ifName |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString MacAddress TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.1053 | IdentityciscoFibreChanMIB | This MIB module defines the managed objects for physical layer characteristics of Fibre Channel interfaces and performance statistics objects for protocol spec… | ||
| 1.3.6.1.4.1.9.9.1053.0 | NodeciscoFibreChanMIBNotifs | |||
| 1.3.6.1.4.1.9.9.1053.1 | NodeciscoFibreChanMIBObjects | |||
| 1.3.6.1.4.1.9.9.1053.1.1 | NodecoiFibreChanController | |||
| 1.3.6.1.4.1.9.9.1053.1.1.1 | TablecoiFibreChanControllerTable | not-accessible | current | This table provides management information for physical layer related attributes of interfaces with an ifType of FibreChannel(56) |
| 1.3.6.1.4.1.9.9.1053.1.1.1.1 | RowcoiFibreChanControllerEntry | not-accessible | current | An entry containing management information on physical layer related attributes of interfaces with an ifType FibreChannel(56). Entries are created by the featu… |
| 1.3.6.1.4.1.9.9.1053.1.1.1.1.1 | ColumncoiFibreChanControllerAdminStatus | read-only | current | This object gives the administration status of the Fibre Channel interfaces. when it is set to down(0), it results in transmitted being stopped and there shoul… |
| 1.3.6.1.4.1.9.9.1053.1.1.1.1.2 | ColumncoiFibreChanControllerOperStatus | read-only | current | This object gives the current operational state of the Fibre Channel controller, valid values are - down(0): The controller is in down state. up(1): The contro… |
| 1.3.6.1.4.1.9.9.1053.1.1.1.1.3 | ColumncoiFibreChanControllerLoopbackInfo | read-only | current | This object gives the loopback value of the Fibre Channel controller, valid values are - loopbackNone(0): No controller loopback info loopbackLine(1): The cont… |
| 1.3.6.1.4.1.9.9.1053.1.1.1.1.4 | ColumncoiFibreChanControllerAlarmStatus | read-only | current | This object indicates the current defect status of the Fibre Channel controller. Valid values are - noAlarm(0): No Alarm. This bit will be set when none of the… |
| 1.3.6.1.4.1.9.9.1053.1.2 | NodecoiFcPm | |||
| 1.3.6.1.4.1.9.9.1053.1.2.1 | NodecoiFcPmCurrentTable | |||
| 1.3.6.1.4.1.9.9.1053.1.2.1.1 | ScalarcoiFcPmCurrentEntry | not-accessible | current | An entry containing Fibre Channel layer performance monitoring current interval data for Fibre Channel Controller. |
| 1.3.6.1.4.1.9.9.1053.1.2.1.1.1 | ScalarcoiFcPmCurrentIntervalType | read-only | current | This object gives the interval type for which Fibre Channel layer current performance monitoring data is collected. |
| 1.3.6.1.4.1.9.9.1053.1.2.1.1.2 | ScalarcoiFcPmIfInOctets | read-only | current | This object gives the number of bytes received since the last counter reset. |
| 1.3.6.1.4.1.9.9.1053.1.2.1.1.3 | ScalarcoiFcPmRxTotalPkts | read-only | current | This object gives the number of receive packets. |
| 1.3.6.1.4.1.9.9.1053.1.2.1.1.4 | ScalarcoiFcPmIfInErrors | read-only | current | This object gives the number of receive errors. |
| 1.3.6.1.4.1.9.9.1053.1.2.1.1.5 | ScalarcoiFcPmRxBadFcs | read-only | current | This object gives the number of received frames with bad FCS, no coding error. |
| 1.3.6.1.4.1.9.9.1053.1.2.1.1.6 | ScalarcoiFcPmRxFramesTooShort | read-only | current | This object gives the number of truncated received frames. |
| 1.3.6.1.4.1.9.9.1053.1.2.1.1.7 | ScalarcoiFcPmRxFramesTooLong | read-only | current | This object gives the number of too long received frames. |
| 1.3.6.1.4.1.9.9.1053.1.2.1.1.8 | ScalarcoiFcPmIfOutOctets | read-only | current | This object gives the number of octets transmitted out of the interface, including framing characters. |
| 1.3.6.1.4.1.9.9.1053.1.2.1.1.9 | ScalarcoiFcPmTxTotalPkts | read-only | current | This object gives the number of transmitted packets. |
| 1.3.6.1.4.1.9.9.1053.1.2.1.1.10 | ScalarcoiFcPmTxBadFcs | read-only | current | This object gives the number of transmitted frames with bad FCS, no coding error. |
| 1.3.6.1.4.1.9.9.1053.1.2.1.1.11 | ScalarcoiFcPmTxFramesTooShort | read-only | current | This object gives the number of truncated transmitted frames. |
| 1.3.6.1.4.1.9.9.1053.1.2.1.1.12 | ScalarcoiFcPmTxFramesTooLong | read-only | current | This object gives the number of too long transmitted frames. |
| 1.3.6.1.4.1.9.9.1053.1.2.1.1.13 | ScalarcoiFcCurrentPmValidData | read-only | current | This variable indicates if the Fibre Channel layer performance monitoring data for the interval identified by coiFcPmCurrentIntervalType is valid. |
| 1.3.6.1.4.1.9.9.1053.1.2.2 | NodecoiFcPmHistoryTable | |||
| 1.3.6.1.4.1.9.9.1053.1.2.2.1 | ScalarcoiFcPmHistoryEntry | not-accessible | current | An entry containing Fibre Channel layer performance monitoring historical interval data for Fibre Channel Controller. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.1 | ScalarcoiFcPmHistoryIntervalType | read-only | current | This object gives the interval type for which Fibre Channel layer historical performance monitoring data is collected. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.2 | ScalarcoiFcPmIntervalNumber | not-accessible | current | This object gives the interval number for Fibre Channel layer performance monitoring data in given interval. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.3 | ScalarcoiFcPmHistoryIfInOctets | read-only | current | This object gives the number of bytes received since the last counter reset. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.4 | ScalarcoiFcPmHistoryRxTotalPkts | read-only | current | This object gives the number of receive packets. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.5 | ScalarcoiFcPmHistoryIfInErrors | read-only | current | This object gives the number of receive errors. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.6 | ScalarcoiFcPmHistoryRxBadFcs | read-only | current | This object gives the number of received frames with bad FCS, no coding error. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.7 | ScalarcoiFcPmHistoryRxFramesTooShort | read-only | current | This object gives the number of truncated received frames. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.8 | ScalarcoiFcPmHistoryRxFramesTooLong | read-only | current | This object gives the number of too long received frames. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.9 | ScalarcoiFcPmHistoryIfOutOctets | read-only | current | This object gives the number of octets transmitted out of the interface, including framing characters. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.10 | ScalarcoiFcPmHistoryTxTotalPkts | read-only | current | This object gives the number of transmitted packets. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.11 | ScalarcoiFcPmHistoryTxBadFcs | read-only | current | This object gives the number of transmitted frames with bad FCS, no coding error. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.12 | ScalarcoiFcPmHistoryTxFramesTooShort | read-only | current | This object gives the number of truncated transmitted frames. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.13 | ScalarcoiFcPmHistoryTxFramesTooLong | read-only | current | This object gives the number of too long transmitted frames. |
| 1.3.6.1.4.1.9.9.1053.1.2.2.1.14 | ScalarcoiFcPmHistoryValidData | read-only | current | This variable indicates if the Fibre Channel layer performance monitoring data for the interval identified by coiFcPmHistoryIntervalType is valid. |
| 1.3.6.1.4.1.9.9.1053.1.3 | NodecoiFecPm | |||
| 1.3.6.1.4.1.9.9.1053.1.3.1 | NodecoiFecPmCurrentTable | |||
| 1.3.6.1.4.1.9.9.1053.1.3.1.1 | ScalarcoiFecPmCurrentEntry | not-accessible | current | An entry containing FEC layer performance monitoring current interval data for Fibre Channel Controller. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.1 | ScalarcoiFecPmCurrentIntervalType | read-only | current | This object gives the interval type for which FEC layer current performance monitoring data is collected. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.2 | ScalarcoiFecPmCorWordErrs | read-only | current | This object gives the number of corrected word errors. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.3 | ScalarcoiFecPmUncorWords | read-only | current | This object gives the number of number of uncorrectable words encountered. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.4 | ScalarcoiFecPmPreFECMin | read-only | current | This object gives the minimum value of PreFEC BER. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.5 | ScalarcoiFecPmPreFECMax | read-only | current | This object gives the maximum value of PreFEC BER. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.6 | ScalarcoiFecPmPreFECAvg | read-only | current | This object gives the average value of PreFEC BER. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.7 | ScalarcoiFecPmPostFECMin | read-only | current | This object gives the minimum value of PostFEC BER. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.8 | ScalarcoiFecPmPostFECMax | read-only | current | This object gives the maximum value of PostFEC BER. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.9 | ScalarcoiFecPmPostFECAvg | read-only | current | This object gives the average value of PostFEC BER. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.10 | ScalarcoiFecPmQFactorMin | read-only | current | This object gives the minimum value of Q Factor. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.11 | ScalarcoiFecPmQFactorMax | read-only | current | This object gives the maximum value of Q Factor. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.12 | ScalarcoiFecPmQFactorAvg | read-only | current | This object gives the average value of Q Factor. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.13 | ScalarcoiFecPmQMarginMin | read-only | current | This object gives the minimum value of Q Margin. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.14 | ScalarcoiFecPmQMarginMax | read-only | current | This object gives the maximum value of Q Margin. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.15 | ScalarcoiFecPmQMarginAvg | read-only | current | This object gives the average value of Q Margin. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.16 | ScalarcoiFecPmInstQMarginMin | read-only | current | This object gives the minimum value of Instantaneous Q Margin. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.17 | ScalarcoiFecPmInstQMarginMax | read-only | current | This object gives the maximum value of Instantaneous Q Margin. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.18 | ScalarcoiFecPmInstQMarginAvg | read-only | current | This object gives the average value of Instantaneous Q Margin. |
| 1.3.6.1.4.1.9.9.1053.1.3.1.1.19 | ScalarcoiFecCurrentPmValidData | read-only | current | This variable indicates if the FEC layer performance monitoring data for the interval identified by coiFecPmCurrentIntervalType is valid. |
| 1.3.6.1.4.1.9.9.1053.1.3.2 | NodecoiFecPmHistoryTable | |||
| 1.3.6.1.4.1.9.9.1053.1.3.2.1 | ScalarcoiFecPmHistoryEntry | not-accessible | current | An entry containing FEC layer performance monitoring historical interval data for Fibre Channel Controller. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.1 | ScalarcoiFecPmHistoryIntervalType | read-only | current | This object gives the interval type for which FEC layer historical performance monitoring data is collected. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.2 | ScalarcoiFecPmIntervalNumber | not-accessible | current | This object gives the interval number for FEC layer performance monitoring data in given interval. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.3 | ScalarcoiFecPmHistoryCorWordErrs | read-only | current | This object gives the number of corrected word errors. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.4 | ScalarcoiFecPmHistoryUncorWords | read-only | current | This object gives the number of number of uncorrectable words encountered. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.5 | ScalarcoiFecPmHistoryPreFECMin | read-only | current | This object gives the minimum value of PreFEC BER. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.6 | ScalarcoiFecPmHistoryPreFECMax | read-only | current | This object gives the maximum value of PreFEC BER. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.7 | ScalarcoiFecPmHistoryPreFECAvg | read-only | current | This object gives the average value of PreFEC BER. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.8 | ScalarcoiFecPmHistoryPostFECMin | read-only | current | This object gives the minimum value of PostFEC BER. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.9 | ScalarcoiFecPmHistoryPostFECMax | read-only | current | This object gives the maximum value of PostFEC BER. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.10 | ScalarcoiFecPmHistoryPostFECAvg | read-only | current | This object gives the average value of PostFEC BER. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.11 | ScalarcoiFecPmHistoryQFactorMin | read-only | current | This object gives the minimum value of Q Factor. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.12 | ScalarcoiFecPmHistoryQFactorMax | read-only | current | This object gives the maximum value of Q Factor. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.13 | ScalarcoiFecPmHistoryQFactorAvg | read-only | current | This object gives the average value of Q Factor. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.14 | ScalarcoiFecPmHistoryQMarginMin | read-only | current | This object gives the minimum value of Q Margin. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.15 | ScalarcoiFecPmHistoryQMarginMax | read-only | current | This object gives the maximum value of Q Margin. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.16 | ScalarcoiFecPmHistoryQMarginAvg | read-only | current | This object gives the average value of Q Margin. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.17 | ScalarcoiFecPmHistoryInstQMarginMin | read-only | current | This object gives the minimum value of Instantaneous Q Margin. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.18 | ScalarcoiFecPmHistoryInstQMarginMax | read-only | current | This object gives the maximum value of Instantaneous Q Margin. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.19 | ScalarcoiFecPmHistoryInstQMarginAvg | read-only | current | This object gives the average value of Instantaneous Q Margin. |
| 1.3.6.1.4.1.9.9.1053.1.3.2.1.20 | ScalarcoiFecPmHistoryValidData | read-only | current | This variable indicates if the FEC layer performance monitoring data for the interval identified by coiFecPmHistoryIntervalType is valid. |
| 1.3.6.1.4.1.9.9.1053.1.4 | NodecoiPcsPm | |||
| 1.3.6.1.4.1.9.9.1053.1.4.1 | NodecoiPcsPmCurrentTable | |||
| 1.3.6.1.4.1.9.9.1053.1.4.1.1 | ScalarcoiPcsPmCurrentEntry | not-accessible | current | An entry containing PCS layer performance monitoring current interval data for Fibre Channel Controller. |
| 1.3.6.1.4.1.9.9.1053.1.4.1.1.1 | ScalarcoiPcsPmCurrentIntervalType | read-only | current | This object gives the interval type for which PCS layer current performance monitoring data is collected. |
| 1.3.6.1.4.1.9.9.1053.1.4.1.1.2 | ScalarcoiPcsPmCumBip | read-only | current | This object gives the cumulative number of BIP errors. |
| 1.3.6.1.4.1.9.9.1053.1.4.1.1.3 | ScalarcoiPcsPmCumFrmError | read-only | current | This object gives the cumulative number of frame errors. |
| 1.3.6.1.4.1.9.9.1053.1.4.1.1.4 | ScalarcoiPcsPmCumBadSh | read-only | current | This object gives the cumulative number of bad sync header errors. |
| 1.3.6.1.4.1.9.9.1053.1.4.1.1.5 | ScalarcoiPcsPmEs | read-only | current | This object gives the number of errored seconds. |
| 1.3.6.1.4.1.9.9.1053.1.4.1.1.6 | ScalarcoiPcsPmSes | read-only | current | This object gives the number of severely errored seconds. |
| 1.3.6.1.4.1.9.9.1053.1.4.1.1.7 | ScalarcoiPcsPmUas | read-only | current | This object gives the number of unavailable seconds. |
| 1.3.6.1.4.1.9.9.1053.1.4.1.1.8 | ScalarcoiPcsPmFarEndEs | read-only | current | This object gives the number of errored seconds on the far end. |
| 1.3.6.1.4.1.9.9.1053.1.4.1.1.9 | ScalarcoiPcsPmFarEndSes | read-only | current | This object gives the number of severely errored seconds on the far end. |
| 1.3.6.1.4.1.9.9.1053.1.4.1.1.10 | ScalarcoiPcsPmFarEndUas | read-only | current | This object gives the number of unavailable seconds on the far end. |
| 1.3.6.1.4.1.9.9.1053.1.4.1.1.11 | ScalarcoiPcsCurrentPmValidData | read-only | current | This variable indicates if the PCS layer performance monitoring data for the interval identified by coiPcsPmCurrentIntervalType is valid. |
| 1.3.6.1.4.1.9.9.1053.1.4.2 | NodecoiPcsPmHistoryTable | |||
| 1.3.6.1.4.1.9.9.1053.1.4.2.1 | ScalarcoiPcsPmHistoryEntry | not-accessible | current | An entry containing PCS layer performance monitoring historical interval data for Fibre Channel Controller. |
| 1.3.6.1.4.1.9.9.1053.1.4.2.1.1 | ScalarcoiPcsPmHistoryIntervalType | read-only | current | This object gives the interval type for which PCS layer historical performance monitoring data is collected. |
| 1.3.6.1.4.1.9.9.1053.1.4.2.1.2 | ScalarcoiPcsPmIntervalNumber | not-accessible | current | This object gives the interval number for PCS layer performance monitoring data in given interval. |
| 1.3.6.1.4.1.9.9.1053.1.4.2.1.3 | ScalarcoiPcsPmHistoryCumBip | read-only | current | This object gives the cumulative number of BIP errors. |
| 1.3.6.1.4.1.9.9.1053.1.4.2.1.4 | ScalarcoiPcsPmHistoryCumFrmError | read-only | current | This object gives the cumulative number of frame errors. |
| 1.3.6.1.4.1.9.9.1053.1.4.2.1.5 | ScalarcoiPcsPmHistoryCumBadSh | read-only | current | This object gives the cumulative number of bad sync header errors. |
| 1.3.6.1.4.1.9.9.1053.1.4.2.1.6 | ScalarcoiPcsPmHistoryEs | read-only | current | This object gives the number of errored seconds. |
| 1.3.6.1.4.1.9.9.1053.1.4.2.1.7 | ScalarcoiPcsPmHistorySes | read-only | current | This object gives the number of severely errored seconds. |
| 1.3.6.1.4.1.9.9.1053.1.4.2.1.8 | ScalarcoiPcsPmHistoryUas | read-only | current | This object gives the number of unavailable seconds. |
| 1.3.6.1.4.1.9.9.1053.1.4.2.1.9 | ScalarcoiPcsPmHistoryEsFe | read-only | current | This object gives the number of errored seconds on the far end. |
| 1.3.6.1.4.1.9.9.1053.1.4.2.1.10 | ScalarcoiPcsPmHistorySesFe | read-only | current | This object gives the number of severely errored seconds on the far end. |
| 1.3.6.1.4.1.9.9.1053.1.4.2.1.11 | ScalarcoiPcsPmHistoryUasFe | read-only | current | This object gives the number of unavailable seconds on the far end. |
| 1.3.6.1.4.1.9.9.1053.1.4.2.1.12 | ScalarcoiPcsPmHistoryValidData | read-only | current | This variable indicates if the PCS layer performance monitoring data for the interval identified by coiPcsPmHistoryIntervalType is valid. |
| 1.3.6.1.4.1.9.9.1053.2 | NodeciscoFibreChanMIBConformance | |||
| 1.3.6.1.4.1.9.9.1053.2.1 | NodeciscoFibreChanMIBCompliances | |||
| 1.3.6.1.4.1.9.9.1053.2.2 | NodeciscoFibreChanMIBGroups |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CoiIntervalType | INTEGER { fifteenMin(1), oneDay(2), thirtySeconds(3) } | current | This value indicates the time period over which performance monitoring data has been collected. Valid values are - fifteenMin(1) - values for the 15 min interval. oneDay(2) - values for the 1 Day interval. thirtySeconds… |