CISCO-LWAPP-HA-MIB
105 objects
This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. This MIB is used to show and configure High availability (HA) related statistics. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ + + + + + + + CC + + CC + + CC + + + + + + + +......+ +......+ +......+ .. . . .. . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + AP + + AP + + AP + + AP + + + + + + + + + +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + MN + + MN + + MN + + MN + + + + + + + + + +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node, Mobile Station(Ms) and client are used interchangeably. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.
Imported Objects
| CISCO-RF-MIB | cRFStatusPeerUnitState cRFStatusUnitState |
| CISCO-SMI | ciscoMgmt |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| RFC1213-MIB | sysName |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString MacAddress RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.843 | IdentityciscoLwappHaMIB | This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from… | ||
| 1.3.6.1.4.1.9.9.843.0 | NodeciscoLwappHaMIBNotifs | |||
| 1.3.6.1.4.1.9.9.843.0.1 | NotificationcLHaSecondaryControllerUsageTrap | current | This notification is sent on the event of a generic failure between the active and peer unit. | |
| 1.3.6.1.4.1.9.9.843.0.2 | NotificationcLHaRFSwapInfoTrap | current | The notification is sent by the active redundant unit whenever its RF state changes or the RF state of the peer unit changes. To avoid a flurry of notification… | |
| 1.3.6.1.4.1.9.9.843.0.3 | NotificationcLHaBulkSyncCompleteTrap | current | The notification is sent by the active redundant unit whenever the BulkSync to peer is complete. | |
| 1.3.6.1.4.1.9.9.843.0.4 | NotificationcLHaPeerHotStandbyTrap | current | The notification is sent by the active redundant unit whenever its peer unit turned hot-standby. | |
| 1.3.6.1.4.1.9.9.843.1 | NodeciscoLwappHaMIBObjects | |||
| 1.3.6.1.4.1.9.9.843.1.1 | NodeciscoLwappHaGlobalConfig | |||
| 1.3.6.1.4.1.9.9.843.1.1.1 | ScalarcLHaApSsoConfig | read-write | current | This object specifies the value of redundancy mode statefull switch over (SSO). A value of 'true' indicates that, redundancy mode SSO is enabled. A value of 'f… |
| 1.3.6.1.4.1.9.9.843.1.1.2 | ScalarcLHaPeerIpAddressType | read-write | current | This object specifies the peer WLC IP address type. |
| 1.3.6.1.4.1.9.9.843.1.1.3 | ScalarcLHaPeerIpAddress | read-write | current | This object specifies the peer WLC IP address. |
| 1.3.6.1.4.1.9.9.843.1.1.4 | ScalarcLHaServicePortPeerIpAddressType | read-write | current | This object specifies the peer WLC service port IP address type. |
| 1.3.6.1.4.1.9.9.843.1.1.5 | ScalarcLHaServicePortPeerIpAddress | read-write | current | This object specifies the peer WLC service port IP address. |
| 1.3.6.1.4.1.9.9.843.1.1.6 | ScalarcLHaServicePortPeerIpNetMaskType | read-write | current | This object specifies the peer WLC service port net mask IP type. |
| 1.3.6.1.4.1.9.9.843.1.1.7 | ScalarcLHaServicePortPeerIpNetMask | read-write | current | This object specifies the peer WLC service port net mask IP address. |
| 1.3.6.1.4.1.9.9.843.1.1.8 | ScalarcLHaRedundancyIpAddressType | read-only | current | This object represents the peer WLC redundancy management interface IP address type. |
| 1.3.6.1.4.1.9.9.843.1.1.9 | ScalarcLHaRedundancyIpAddress | read-only | current | This object represents the peer WLC redundancy management interface IP address. |
| 1.3.6.1.4.1.9.9.843.1.1.10 | ScalarcLHaPeerMacAddress | read-only | current | This object represents the peer WLC mac address. |
| 1.3.6.1.4.1.9.9.843.1.1.11 | ScalarcLHaVirtualMacAddress | read-write | current | This object specifies the peer WLC mobility MAC address. |
| 1.3.6.1.4.1.9.9.843.1.1.12 | ScalarcLHaPrimaryUnit | read-write | current | This object specifies whether this is the primary or secondary unit. A value of 'true' indicates that, this unit is the primary unit. A value of 'false' indica… |
| 1.3.6.1.4.1.9.9.843.1.1.13 | ScalarcLHaLinkEncryption | read-write | current | This object specifies whether link encryption is enabled or disabled. A value of 'true' indicates that, link encryption is enabled. A value of 'false' indicate… |
| 1.3.6.1.4.1.9.9.843.1.1.14 | ScalarcLHaNetworkFailOver | read-write | current | This object specifies whether network failover is enabled or disabled. A value of 'true' indicates that, network failover is enabled. A value of 'false' indica… |
| 1.3.6.1.4.1.9.9.843.1.1.15 | ScalarcLHaRFStatusUnitIp | read-only | current | This object specifies the peer IP address when Redundancy Framwork(RF) state of active/peer unit changes. |
| 1.3.6.1.4.1.9.9.843.1.1.16 | ScalarcLHaKATimeout | read-write | current | This object specifies keep alive timeout value in milli seconds between 100 and 1000. The value for this object configured in multiples of 50. |
| 1.3.6.1.4.1.9.9.843.1.1.17 | ScalarcLHaKARetryCount | read-write | current | This object specifies keep alive retry count and The value for this object configured between 3 and 10. |
| 1.3.6.1.4.1.9.9.843.1.1.18 | ScalarcLHaGwRetryCount | read-write | current | This object specifies default gateway reachability retry count and The value for this object configured between 6 and 12. |
| 1.3.6.1.4.1.9.9.843.1.1.19 | ScalarcLHaPeerSearchTimeout | read-write | current | This object specifies peer search timeout and The value for this object configured between 60 and 300 seconds. |
| 1.3.6.1.4.1.9.9.843.1.1.20 | ScalarcLHaRFStatusUnitIpType | read-only | current | This object specifies the peer IP address type when redundancy framwork(RF) state of active/peer unit changes. |
| 1.3.6.1.4.1.9.9.843.1.2 | NodeciscoLwappHaNetworkConfig | |||
| 1.3.6.1.4.1.9.9.843.1.2.1 | TablecLHaNetworkRoutePeerConfigTable | not-accessible | current | This table represents the peer network route entries. |
| 1.3.6.1.4.1.9.9.843.1.2.1.1 | RowcLHaNetworkRoutePeerConfigEntry | not-accessible | current | Each entry contains configuration of peer network route. |
| 1.3.6.1.4.1.9.9.843.1.2.1.1.1 | ColumncLHaNetworkRoutePeerIPAddressType | not-accessible | current | This object represents peer network route IP address type. |
| 1.3.6.1.4.1.9.9.843.1.2.1.1.2 | ColumncLHaNetworkRoutePeerIPAddress | not-accessible | current | This object represents peer network route IP address. |
| 1.3.6.1.4.1.9.9.843.1.2.1.1.3 | ColumncLHaNetworkRoutePeerIPNetmaskType | read-create | current | This object specifies peer network route IP netmask type. |
| 1.3.6.1.4.1.9.9.843.1.2.1.1.4 | ColumncLHaNetworkRoutePeerIPNetmask | read-create | current | This object specifies peer network route IP netmask. |
| 1.3.6.1.4.1.9.9.843.1.2.1.1.5 | ColumncLHaNetworkRoutePeerGatewayType | read-create | current | This object represents peer network route gateway IP type. |
| 1.3.6.1.4.1.9.9.843.1.2.1.1.6 | ColumncLHaNetworkRoutePeerGateway | read-create | current | This object specifies peer network route gateway IP address. |
| 1.3.6.1.4.1.9.9.843.1.2.1.1.7 | ColumncLHaNetworkRoutePeerTransferStatus | read-only | current | This object represents peer network route transfer status. A value of initiate(1) indicates that, network route transfer initiated. A value of inProgress(2) in… |
| 1.3.6.1.4.1.9.9.843.1.2.1.1.8 | ColumncLHaNetworkRoutePeerRowStatus | read-create | current | This object specifies status column for this row and used to create and delete specific instances of rows in this table. |
| 1.3.6.1.4.1.9.9.843.1.3 | NodeciscoLwappHaNotificationVariable | |||
| 1.3.6.1.4.1.9.9.843.1.3.1 | ScalarcLHaSecondaryControllerUsageTrapType | read-only | current | This object represents the usage of secondary controller. After the usuage of 90 days, one trap is generated per day for over usage. A value of usageStart(1) i… |
| 1.3.6.1.4.1.9.9.843.1.3.2 | ScalarcLHaSecondaryControllerUsageDayCounter | read-only | current | This object represents the number of days the secondary controller is used. |
| 1.3.6.1.4.1.9.9.843.1.3.3 | ScalarcLHaBulkSyncCompleteEvent | read-only | current | This object represents the time when the bulksync was complete. |
| 1.3.6.1.4.1.9.9.843.1.3.4 | ScalarcLHaPeerHotStandbyEvent | read-only | current | This object represents that the peer has turned hot-standby. |
| 1.3.6.1.4.1.9.9.843.1.4 | NodeciscoLwappHaPeerStatisticsVariable | |||
| 1.3.6.1.4.1.9.9.843.1.4.1 | NodeciscoLwappHaSystemStatistics | |||
| 1.3.6.1.4.1.9.9.843.1.4.1.1 | NodeciscoLwappHaCpuStatistics | |||
| 1.3.6.1.4.1.9.9.843.1.4.1.1.1 | ScalarcLHaAllCpuUsage | read-only | current | This object represents the all CPUs usage of peer. |
| 1.3.6.1.4.1.9.9.843.1.4.1.2 | NodeciscoLwappHaPowerSupplyStatistics | |||
| 1.3.6.1.4.1.9.9.843.1.4.1.2.1 | ScalarcLHaPowerSupply1Present | read-only | current | This object represents whether peer switch power Supply 1 is enabled or disabled. A value of 'true' indicates that, peer switch power supply 1 is enabled. A va… |
| 1.3.6.1.4.1.9.9.843.1.4.1.2.2 | ScalarcLHaPowerSupply1Operational | read-only | current | This object represents whether peer switch power supply 1 operational or not. A value of 'true' indicates that, peer switch power supply 1 operational is enabl… |
| 1.3.6.1.4.1.9.9.843.1.4.1.2.3 | ScalarcLHaPowerSupply2Present | read-only | current | This object represents whether peer switch power supply 2 is enabled or disabled. A value of 'true' indicates that, peer switch power supply 2 is enabled. A va… |
| 1.3.6.1.4.1.9.9.843.1.4.1.2.4 | ScalarcLHaPowerSupply2Operational | read-only | current | This object represents whether Peer switch power Supply 2 operational or not. A value of 'true' indicates that, peer switch power supply 2 operational is enabl… |
| 1.3.6.1.4.1.9.9.843.1.4.1.3 | NodeciscoLwappHaMemoryStatistics | |||
| 1.3.6.1.4.1.9.9.843.1.4.1.3.1 | ScalarcLHaTotalSystemMemory | read-only | current | This object represents the total system memory in Kbytes. |
| 1.3.6.1.4.1.9.9.843.1.4.1.3.2 | ScalarcLHaFreeSystemMemory | read-only | current | This object represents the free system memory in Kbytes. |
| 1.3.6.1.4.1.9.9.843.1.4.1.3.3 | ScalarcLHaUsedSystemMemory | read-only | current | This object represents the used system memory in Kbytes. |
| 1.3.6.1.4.1.9.9.843.1.4.1.3.4 | ScalarcLHaAllocatedFromRtos | read-only | current | This object represents the number of bytes allocated from RTOS in Kbytes. |
| 1.3.6.1.4.1.9.9.843.1.4.1.3.5 | ScalarcLHaChunksFree | read-only | current | This object represents the number of free chunks. |
| 1.3.6.1.4.1.9.9.843.1.4.1.3.6 | ScalarcLHaMmappedRegions | read-only | current | This object represents the number of memory mapped regions. |
| 1.3.6.1.4.1.9.9.843.1.4.1.3.7 | ScalarcLHaSpaceInMmappedRegions | read-only | current | This object represents the space in the memory mapped regions in Kbytes. |
| 1.3.6.1.4.1.9.9.843.1.4.1.3.8 | ScalarcLHaTotalAllocatedSpace | read-only | current | This object represents the total allocated space in Kbytes. |
| 1.3.6.1.4.1.9.9.843.1.4.1.3.9 | ScalarcLHaTotalNotInUseSpace | read-only | current | This object represents the total space not in-use in Kbytes. |
| 1.3.6.1.4.1.9.9.843.1.4.1.3.10 | ScalarcLHaTopMostReleasableSpace | read-only | current | This object represents the top most releasable space in Kbytes. |
| 1.3.6.1.4.1.9.9.843.1.4.1.3.11 | ScalarcLHaTotalAllocatedInclMmap | read-only | current | This object represents the total memory allocated including memory map in Kbytes. |
| 1.3.6.1.4.1.9.9.843.1.4.1.3.12 | ScalarcLHaTotalUsedMmap | read-only | current | This object represents the total memory in-use including memory map in Kbytes. |
| 1.3.6.1.4.1.9.9.843.1.4.1.3.13 | ScalarcLHaTotalFreeInclMmap | read-only | current | This object represents the total free memory including memory map in Kbytes. |
| 1.3.6.1.4.1.9.9.843.1.5 | NodeciscoLwappHaStatisticsVariable | |||
| 1.3.6.1.4.1.9.9.843.1.5.1 | ScalarcLHaAvgPeerReachLatency | read-only | current | This object represents average value of peer controller reachable latency in micro seconds. |
| 1.3.6.1.4.1.9.9.843.1.5.2 | ScalarcLHaAvgGwReachLatency | read-only | current | This object represents average value of default gate way reachable latency in micro seconds. |
| 1.3.6.1.4.1.9.9.843.1.5.3 | ScalarcLHaBulkSyncStatus | read-only | current | This object represents current status of bulk sync. |
| 1.3.6.1.4.1.9.9.843.1.6 | NodeciscoLwappMcHaConfig | |||
| 1.3.6.1.4.1.9.9.843.1.6.1 | ScalarcLMcHaPortName | read-write | current | This object allows user to specify and get the interface name designated as the HA Interface in Multi-Chassis HA environments. This will be applicable only on … |
| 1.3.6.1.4.1.9.9.843.1.6.2 | ScalarcLMcHaPortLocIpAddrType | read-write | current | This object represents the IP version to be used for HA transport. This object will apply to both local IP and the cLMcHaPortMask |
| 1.3.6.1.4.1.9.9.843.1.6.3 | ScalarcLMcHaPortLocIp | read-write | current | This object allows user to specify and get the Local chassis IPv4 Address to establish the HA communication. This IP Address will be assigned to the HA Port on… |
| 1.3.6.1.4.1.9.9.843.1.6.4 | ScalarcLMcHaPortMask | read-write | current | This object allows user to specify and get the network mask for the local chassis IPv4 Address to establish the HA communication. This netmask will be assigned… |
| 1.3.6.1.4.1.9.9.843.1.6.5 | ScalarcLMcHaPortRemoteIpAddrType | read-write | current | This object represents the IP version to be used for HA transport. |
| 1.3.6.1.4.1.9.9.843.1.6.6 | ScalarcLMcHaPortRemIp | read-write | current | This object allows user to specify and get the peer chassis IPv4 Address to establish the HA communication. |
| 1.3.6.1.4.1.9.9.843.1.6.7 | ScalarcLMcHaKeepAliveTimeOut | read-write | current | This object specifies keep alive timeout value in milli seconds between 100 and 1000. The value for this object configured in multiples of 100. |
| 1.3.6.1.4.1.9.9.843.1.6.8 | ScalarcLMcHaChassisPriority | read-write | current | This object allows user to specify and get the current chassis priority. The higher the priority, higher the chance of local chassis becoming the Active. |
| 1.3.6.1.4.1.9.9.843.1.6.9 | ScalarcLMcHaClearConfig | read-write | current | This object allows user to remove the multi-chassis HA configuration. When get, TRUE value indicating HA configuration is cleared, FALSE means not. |
| 1.3.6.1.4.1.9.9.843.1.6.10 | ScalarcLMcHaKeepAliveRetryCount | read-write | current | This object specifies keep alive retry count and The value for this object configured between 3 and 10. |
| 1.3.6.1.4.1.9.9.843.1.7 | NodeciscoLwappMcRmiConfig | |||
| 1.3.6.1.4.1.9.9.843.1.7.1 | ScalarcLMcRmiConfigAction | read-write | current | This object allows user to remove the RMI configuration. When get, 1 value indicating RMI configuration is applied , 2 means clear config. |
| 1.3.6.1.4.1.9.9.843.1.7.2 | ScalarcLMcRmiInterface | read-write | current | This object specifies Chassis/Switch number and The value for this object is between 1 and 15. |
| 1.3.6.1.4.1.9.9.843.1.7.3 | ScalarcLMcRmiChassisANum | read-write | current | This object specifies Chassis/Switch number and The value for this object is between 1 and 15. |
| 1.3.6.1.4.1.9.9.843.1.7.4 | ScalarcLMcRmiChassisAIpAddrType | read-write | current | This object represents IP version to be used for RMI transport |
| 1.3.6.1.4.1.9.9.843.1.7.5 | ScalarcLMcRmiChassisAIp | read-write | current | This object allows user to specify and get the chassis. IPv4 Address to establish the RMI communication. This IP Address will be assigned to the RMI Port on th… |
| 1.3.6.1.4.1.9.9.843.1.7.6 | ScalarcLMcRmiChassisBNum | read-write | current | This object specifies Chassis/Switch number and The value for this object is between 1 and 15. |
| 1.3.6.1.4.1.9.9.843.1.7.7 | ScalarcLMcRmiChassisBIpAddrType | read-write | current | This object represents IP version to be used for RMI transport |
| 1.3.6.1.4.1.9.9.843.1.7.8 | ScalarcLMcRmiChassisBIp | read-write | current | This object allows user to specify and get the chassis. IPv4 Address to establish the RMI communication. This IP Address will be assigned to the RMI Port on th… |
| 1.3.6.1.4.1.9.9.843.1.7.9 | ScalarcLMcRmiGatewayFailover | read-write | current | This object allows user to enable/disable RMI Gateway-Failover configuration. When get, TRUE value indicating RMI Gateway-Failover configuration is enabled, FA… |
| 1.3.6.1.4.1.9.9.843.1.7.10 | ScalarcLMcRmiGatewayFailoverInterval | read-write | current | This object specifies Gateway-Failover interval and The value for this object is between 6 and 12. |
| 1.3.6.1.4.1.9.9.843.2 | NodeciscoLwappHaMIBConform | |||
| 1.3.6.1.4.1.9.9.843.2.1 | NodeciscoLwappHaMIBCompliances | |||
| 1.3.6.1.4.1.9.9.843.2.1.1 | ComplianceciscoLwappHaMIBCompliance | deprecated | This is a default module-compliance containing default object groups. | |
| 1.3.6.1.4.1.9.9.843.2.1.2 | ComplianceciscoLwappHaMIBComplianceRev1 | current | This is a default module-compliance containing default object groups. | |
| 1.3.6.1.4.1.9.9.843.2.2 | NodeciscoLwappHaMIBGroups | |||
| 1.3.6.1.4.1.9.9.843.2.2.1 | GroupciscoLwappHaGlobalConfigGroup | current | This collection of objects represents the information about global config of the high availability objects on the controller. | |
| 1.3.6.1.4.1.9.9.843.2.2.2 | GroupciscoLwappHaNetworkConfigGroup | current | This collection of objects represents the information about network config of the high availability objects on the controller. | |
| 1.3.6.1.4.1.9.9.843.2.2.3 | GroupciscoLwappHaStatisticsGroup | current | This collection of objects represents the information about the Statistics of high availability objects on the controller. | |
| 1.3.6.1.4.1.9.9.843.2.2.4 | GroupciscoLwappHaMIBNotificationVariableGroup | current | This collection of objects represents the information about the Notification of high availability objects on the controller. | |
| 1.3.6.1.4.1.9.9.843.2.2.5 | GroupciscoLwappHaMIBNotificationGroup | current | This supplemental collection of objects represents the HA related notifications sent by the agent to a network management station. | |
| 1.3.6.1.4.1.9.9.843.2.2.6 | GroupciscoLwappMcHaConfigGroup | current | This collection of objects represents the information about network config of the multi chassis high availability RMI objects on the controller. | |
| 1.3.6.1.4.1.9.9.843.2.2.7 | GroupciscoLwappMcRmiConfigGroup | current | This collection of objects represents the information about network config of the multi chassis RMI objects on the controller. |