CISCO-LWAPP-RF-MIB
145 objects
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. This MIB helps to manage the Radio Frequency (RF) parameters on the controller. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected to. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the controllers. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. 802.1x The IEEE ratified standard for enforcing port based access control. This was originally intended for use on wired LANs and later extended for use in 802.11 WLAN environments. This defines an architecture with three main parts - a supplicant (Ex. an 802.11 wireless client), an authenticator (the AP) and an authentication server(a Radius server). The authenticator passes messages back and forth between the supplicant and the authentication server to enable the supplicant get authenticated to the network. Radio Frequency ( RF ) Radio frequency (RF) is a rate of oscillation in the range of about 3 kHz to 300 GHz, which corresponds to the frequency of radio waves, and the alternating currents which carry radio signals. Received Signal Strength Indicator ( RSSI ) A measure of the strength of the signal as observed by the entity that received it, expressed in 'dbm'. Coverage Hole Detection ( CHD ) If clients on an Access Point are detected at low RSSI levels, it is considered a coverage hole by the Access Points. This indicates the existence of an area where clients are continually getting poor signal coverage, without having a viable location to roam to. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol [3] IEEE 802.11 - The original 1 Mbit/s and 2 Mbit/s, 2.4 GHz RF and IR standard.
Imported Objects
| CISCO-LWAPP-TC-MIB | CLApIfType |
| CISCO-LWAPP-WLAN-MIB | cLAPGroupName |
| CISCO-SMI | ciscoMgmt |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | RowStatus StorageType TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.778 | IdentityciscoLwappRFMIB | This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel … | ||
| 1.3.6.1.4.1.9.9.778.0 | NodeciscoLwappRFMIBNotifs | |||
| 1.3.6.1.4.1.9.9.778.1 | NodeciscoLwappRFMIBObjects | |||
| 1.3.6.1.4.1.9.9.778.1.1 | NodeciscoLwappRFConfig | |||
| 1.3.6.1.4.1.9.9.778.1.1.1 | TablecLAPGroupsRFProfileTable | not-accessible | current | This table lists the mapping between an RF profile and an AP group. |
| 1.3.6.1.4.1.9.9.778.1.1.1.1 | RowcLAPGroupsRFProfileEntry | not-accessible | current | An entry containing the configuration attributes that affect the operation of the APs within a group. Entries can be added/deleted by explicit management actio… |
| 1.3.6.1.4.1.9.9.778.1.1.1.1.1 | ColumncLAPGroups802dot11bgRFProfileName | read-write | current | This object specifies the RF profile name assigned to this site on the 802.11bg radio. This profile being assigned should exist in the 'cLRFProfileTable'. To d… |
| 1.3.6.1.4.1.9.9.778.1.1.1.1.2 | ColumncLAPGroups802dot11aRFProfileName | read-write | current | This object specifies the RF profile name assigned to this site on the 802.11a radio. This profile being assigned should exist in the 'cLRFProfileTable'. To di… |
| 1.3.6.1.4.1.9.9.778.1.1.2 | TablecLRFProfileTable | not-accessible | current | This table lists the configuration for each RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1 | RowcLRFProfileEntry | not-accessible | current | An entry containing the configuration attributes that affect the operation of 802.11 RF domain. Entries can be added/deleted by explicit management action from… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.1 | ColumncLRFProfileName | not-accessible | current | This object uniquely identifies a RF Profile. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.2 | ColumncLRFProfileDescr | read-create | current | This object specifies a human-readable description of the profile. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.3 | ColumncLRFProfileTransmitPowerMin | read-create | current | This object specifies the lower bound of transmit power value supported by an AP. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.4 | ColumncLRFProfileTransmitPowerMax | read-create | current | This object specifies the uppoer bound of transmit power value supported by an AP. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.5 | ColumncLRFProfileTransmitPowerThresholdV1 | read-create | current | This object specifies the transmit power control version 1 threshold for the radio resource management algorithm. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.6 | ColumncLRFProfileTransmitPowerThresholdV2 | read-create | current | This object specifies the transmit power control version 2 threshold for the radio resource management algorithm. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.7 | ColumncLRFProfileDataRate1Mbps | read-create | current | This object specifies the configuration for this data rate. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.8 | ColumncLRFProfileDataRate2Mbps | read-create | current | This object specifies the configuration for this data rate. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.9 | ColumncLRFProfileDataRate5AndHalfMbps | read-create | current | This object specifies the configuration for this data rate. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.10 | ColumncLRFProfileDataRate11Mbps | read-create | current | This object specifies the configuration for this data rate. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.11 | ColumncLRFProfileDataRate6Mbps | read-create | current | This object specifies the configuration for this data rate. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.12 | ColumncLRFProfileDataRate9Mbps | read-create | current | This object specifies the configuration for this data rate. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.13 | ColumncLRFProfileDataRate12Mbps | read-create | current | This object specifies the configuration for this data rate. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.14 | ColumncLRFProfileDataRate18Mbps | read-create | current | This object specifies the configuration for this data rate. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.15 | ColumncLRFProfileDataRate24Mbps | read-create | current | This object specifies the configuration for this data rate. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.16 | ColumncLRFProfileDataRate36Mbps | read-create | current | This object specifies the configuration for this data rate. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.17 | ColumncLRFProfileDataRate48Mbps | read-create | current | This object specifies the configuration for this data rate. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.18 | ColumncLRFProfileDataRate54Mbps | read-create | current | This object specifies the configuration for this data rate. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.19 | ColumncLRFProfileRadioType | read-create | current | This object is used to configure the radio type for this profile. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.20 | ColumncLRFProfileStorageType | read-create | current | This object represents the storage type for this conceptual row. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.21 | ColumncLRFProfileRowStatus | read-create | current | This is the status column for this row and used to create and delete specific instances of rows in this table. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.22 | ColumncLRFProfileHighDensityMaxRadioClients | read-create | current | This object specifies the maximum number of clients per AP radio in high density environment. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.23 | ColumncLRFProfileBandSelectProbeResponse | read-create | current | This object specifies the AP's probe response with clients to verify whether client can associate on both 2.4 GHz and 5Ghz spectrum. When set to true, AP suppr… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.24 | ColumncLRFProfileBandSelectCycleCount | read-create | current | This object specifies number of times a client probe (2.4 G-Hz) is suppressed before the AP starts responding to the probes. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.25 | ColumncLRFProfileBandSelectCycleThreshold | read-create | current | This object specifies time threshold for a new scanning mobile station period. Mobile station cycle counter will increment only if mobile station scans same ch… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.26 | ColumncLRFProfileBandSelectExpireSuppression | read-create | current | This object specifies the duration at which an AP waits to conduct another probe suppression. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.27 | ColumncLRFProfileBandSelectExpireDualBand | read-create | current | This object specifies the timeout duration until which an AP should not respond to 2.4ghz probe requests from a dual-band client. Once this band select duratio… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.28 | ColumncLRFProfileBandSelectClientRSSI | read-create | current | This object specifies minimum mobile station RSSI threshold. Mobile stations having RSSI below this value will not be recorded in the suppressed table. This co… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.29 | ColumncLRFProfileLoadBalancingWindowSize | read-create | current | This object specifies the minimum number of clients to be associated on an AP in order to trigger load balancing. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.30 | ColumncLRFProfileLoadBalancingMaxDenialCount | read-create | current | This object specifies maximum number of association rejections sent by AP to a mobile station for a given sequence of association. When a mobile station tries … |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.31 | ColumncLRFProfileCHDDataRSSIThreshold | read-create | current | This object specifies the RSSI value for non-voice clients i.e., clients sending only data traffic to trigger coverage event. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.32 | ColumncLRFProfileCHDVoiceRSSIThreshold | read-create | current | This object specifies the RSSI value for voice clients to trigger coverage event. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.33 | ColumncLRFProfileCHDClientExceptionLevel | read-create | current | This object specifies the minimum number of clients required to trigger coverage hole. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.34 | ColumncLRFProfileCHDCoverageExceptionLevel | read-create | current | This object specifies the minimum percentage of clients in the coverage hole region of the AP, required to trigger a coverage hole exception |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.35 | ColumncLRFProfileMulticastDataRate | read-create | current | This object specifies the minimum data rate at which multicast clients can associate to AP. A value 0 indicates that AP will automatically adjust data rates. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.36 | ColumncLRFProfile11nOnly | read-create | current | This object specifies if 11n-client-only mode is enabled. A value of 'true' indicates 11n-client-only mode enabled. A value of 'false' indicates 11n-client-onl… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.37 | ColumncLRFProfileHDClientTrapThreshold | read-create | current | This object specifies the threshold number of clients per AP radio to trigger a trap. The trap ciscoLwappApClientThresholdNotify will be triggered once the cou… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.38 | ColumncLRFProfileInterferenceThreshold | read-create | current | This object specifies interference threshold in % traps are generated when interference exceeds this value . |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.39 | ColumncLRFProfileNoiseThreshold | read-create | current | This object specifies the threshold number of noise threshold between -127 and 0 dBm. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.40 | ColumncLRFProfileUtilizationThreshold | read-create | current | This object specifies the threshold of bandwidth (%) being utilized by an access-point. Traps are sent when this value is exceeded |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.41 | ColumncLRFProfileDCAForeignContribution | read-create | current | This object specifies whether foreign interference is taken into account for the DCA metrics. A value of 'true' indicates that foreign interference is is consi… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.42 | ColumncLRFProfileDCAChannelWidth | read-create | current | This object specifies how the system performs DCA channel width selection for the RFProfile twenty - 20MHz channel width supported by this radio. forty - 40MHz… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.43 | ColumncLRFProfileDCAChannelList | read-create | current | This object specifies the 802.11 channels available to the RF Profile. A comma separated list of integers. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.44 | ColumncLRFProfileRxSopThreshold | read-create | current | This object specifies the receiver start of packet threshold for the rf profile. auto - Reverts radio receiver SOP to auto. high - Sets radio receiver SOP to h… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.45 | ColumncLRFProfileHSRMode | read-create | current | This object specifies whether HSR mode for RF profile is enabled or not. A value of 'true' indicates that HSR is enabled. A value of 'false' indicates that HSR… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.46 | ColumncLRFProfileHSRNeighborTimeoutFactor | read-create | current | This object specifies the timeout interval of neighbors that will be configured for RF profile. Neighbor timeout factor will be five times the neighbor interval |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.47 | ColumncLRFProfileBandSelectClientMidRSSI | read-create | current | This object specifies medium mobile station RSSI threshold. Mobile station between this value and cldBandSelectClientRssi will be recorded in suppressed table … |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.48 | ColumncLRFProfileClientNetworkPreference | read-create | current | This object represents the client network preference. default(0) - RRM Algorithm has no preference on the clients. connectivity(1) - RRM Algorithm has a prefer… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.49 | ColumncLRFProfileUnusedChannelList | read-only | current | This object specifies the 802.11 channels present in ths un-used channel list of RF Profile. A comma separated list of integers. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.50 | ColumncLRFProfileShutdown | read-write | current | This object specifies if rf profile is disabled. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.51 | ColumncLRFProfileAirTimeFairnessMode | read-write | current | This object specifies the mode of fairness for ATF supported APs, joined to the controller. disable(1) - This indicates that fairness mode is disabled. SSID Mo… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.52 | ColumncLRFProfileAirTimeFairnessOptimization | read-write | current | This object specifies the optimization for ATF supported APs, joined to the controller to be configured. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.53 | ColumncLRFProfileBridgeClientAccess | read-write | current | This object specifies whether airtime allocation is enabled for the client access node. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.54 | ColumncLRFProfileAirTimeAllocation | read-write | current | This object specifies the percentage for airtime allocation for the client access node. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.55 | ColumncLRFProfileRxSopThresholdCustom | read-write | current | This object specifies the percentage for the receiver start of packet custom threshold for the client access node. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.56 | ColumncLRFProfile11axObssPdEnable | read-write | current | This object specifies whether 802.11ax OBSS PD spatial reuse is enabled for the RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.57 | ColumncLRFProfile11axNonSrgObssPdMax | read-write | current | This object specifies the non-SRG OBSS PD max threshold in dBm for the RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.58 | ColumncLRFProfileNdpMode | read-create | current | This object specifies the neighbor discovery mode of AP for this RF profile auto - neighbor discovery mode is auto. offChannel - neighbor discovery mode is off… |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.59 | ColumncLRFProfile11ax6GHzFeature | read-write | current | This object specifies whether 802.11ax UBPR or FILS discovery enabled for the RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.60 | ColumncLRFProfile11axBcastProbeRespInterval | read-write | current | This object specifies the 802.11ax Broadcast Probe response interval in msec. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.62 | ColumncLRFProfileMultiBssidProfile | read-write | current | This object specifies the Multi-BSSID profile name that is mapped to the RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.63 | ColumncLRFProfilePSCBias | read-write | current | This object specifies whether preferred scanning channel bias for 6 GHz DCA is enabled or disabled for the RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.64 | ColumncLRFProfile11axSrgObssPdEnable | read-write | current | This object specifies whether 802.11ax SRG OBSS PD spatial reuse is enabled for the RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.65 | ColumncLRFProfile11axSrgObssPdMin | read-write | current | This object specifies the SRG OBSS PD min threshold in dBm for the RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.66 | ColumncLRFProfile11axSrgObssPdMax | read-write | current | This object specifies the SRG OBSS PD max threshold in dBm for the RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.2.1.67 | ColumncLRFProfilePreamblePuncture | read-write | current | This object specifies whether Preamble puncturing is enabled for the RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.3 | TablecLRFProfileMcsDataRateTable | not-accessible | current | This object specifies the 11n MCS rates supported by the RF profile, indexed by the MCS rate, ranging from 1 to 32, corresponding to rate MCS-0, MCS-1, ... MCS… |
| 1.3.6.1.4.1.9.9.778.1.1.3.1 | RowcLRFProfileMcsDataRateEntry | not-accessible | current | An entry containing MCS date rate information applicable to a particular profile. Entry is added to the table when the data rate is set to 'supported' or 'mand… |
| 1.3.6.1.4.1.9.9.778.1.1.3.1.1 | ColumncLRFProfileMcsName | not-accessible | current | This object uniquely identifies a RF Profile. |
| 1.3.6.1.4.1.9.9.778.1.1.3.1.2 | ColumncLRFProfileMcsRate | not-accessible | current | This object uniquely identifies the MCS data rate for a particular profile. |
| 1.3.6.1.4.1.9.9.778.1.1.3.1.3 | ColumncLRFProfileMcsRateSupport | read-write | current | This object is used to enable or disable the data rate. A value of 'true' indicates MCS support is enabled. A value of 'false' indicates MCS support is disable… |
| 1.3.6.1.4.1.9.9.778.1.1.4 | TablecLRFProfileChannelListTable | not-accessible | current | This object specifies the list of channels that is available for DCA of a RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.4.1 | RowcLRFProfileChannelListEntry | not-accessible | current | An entry containing Channel List information applicable to a particular profile. |
| 1.3.6.1.4.1.9.9.778.1.1.4.1.1 | ColumncLRFProfileChanNumber | not-accessible | current | This object uniquely identifies the channel for a particular profile. |
| 1.3.6.1.4.1.9.9.778.1.1.4.1.2 | ColumncLRFProfileChanAddRemove | read-create | current | This object specifies a channel is to be added or removed from DCA list of the RFProfile. add - Add the channel to global DCA channel list. remove - Removed th… |
| 1.3.6.1.4.1.9.9.778.1.1.4.1.3 | ColumncLRFProfileChanRowStatus | read-create | current | This is the status column for this row and used to create and delete specific instances of rows in this table. |
| 1.3.6.1.4.1.9.9.778.1.1.5 | TablecLRFProfileRemoveChannelTable | not-accessible | current | This table represents the removed channel information from default DCA channel list for an AP's 802.11 interface using the RF profile. Based on the country tha… |
| 1.3.6.1.4.1.9.9.778.1.1.5.1 | RowcLRFProfileRemoveChannelEntry | not-accessible | current | Each entry in this table provides the removed channel information from the default DCA channel list for this RF profile |
| 1.3.6.1.4.1.9.9.778.1.1.5.1.1 | ColumncLRFProfileRemoveChannelName | not-accessible | current | This object uniquely identifies a RF Profile. |
| 1.3.6.1.4.1.9.9.778.1.1.5.1.2 | ColumncLRFProfileRemoveChannelNum | not-accessible | current | The channel nubmer for this entry. This value represents the unique channel number removed from default DCA channel list for this RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.5.1.3 | ColumncLRFProfileRemovedChannelDcaState | read-create | current | This object specifies whether this channel is part of the dynamic channel allocation (DCA) Remove List. A value of 'false' indicates that the DCA for this chan… |
| 1.3.6.1.4.1.9.9.778.1.1.5.1.4 | ColumncLRFProfileRemoveChannelRowStatus | read-create | current | The status of this conceptual row. All writable objects in this row may be modified at any time. |
| 1.3.6.1.4.1.9.9.778.1.1.6 | TablecLRFProfileAddChannelTable | not-accessible | current | This table represents the added channel information to the default DCA channel list in this RF profile. Based on the country that an AP operates in, it gets as… |
| 1.3.6.1.4.1.9.9.778.1.1.6.1 | RowcLRFProfileAddChannelEntry | not-accessible | current | Each entry in this table provides the added channel information to the default DCA channel list in this RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.6.1.1 | ColumncLRFProfileAddChannelName | not-accessible | current | This object uniquely identifies a RF Profile. |
| 1.3.6.1.4.1.9.9.778.1.1.6.1.2 | ColumncLRFProfileAddChannelNum | not-accessible | current | The channel nubmer for this entry. This value represents the unique channel number added to the default DCA list in this RF profile. |
| 1.3.6.1.4.1.9.9.778.1.1.6.1.3 | ColumncLRFProfileAddedChannelDcaState | read-create | current | This object specifies whether this channel is part of the dynamic channel allocation (DCA) Add List. A value of 'true' indicates that the DCA for this channel … |
| 1.3.6.1.4.1.9.9.778.1.1.6.1.4 | ColumncLRFProfileAddChannelRowStatus | read-create | current | The status of this conceptual row. All writable objects in this row may be modified at any time. |
| 1.3.6.1.4.1.9.9.778.1.1.7 | TablecLMultiBSSIDProfileTable | not-accessible | current | This table represents the configuration related to each Multi BSSID profile. |
| 1.3.6.1.4.1.9.9.778.1.1.7.1 | RowcLMultiBSSIDProfileEntry | not-accessible | current | Each entry in this table stores the configurations related to a Multi BSSID Profile. Entries can be added/deleted by explicit management action from NMS/EMS or… |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.1 | ColumncLMultiBSSIDProfileName | not-accessible | current | This object uniquely identifies a Multi BSSID Profile. |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.2 | ColumncLMultiBSSIDProfileDescr | read-create | current | This object specifies a human-readable description of the Multi BSSID profile. |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.3 | ColumncLMultiBSSIDProfile11axOfdmaDownLink | read-create | current | This object specifies if 802.11ax OFDMA Downlink is enabled. A value of 'true' indicates 802.11ax OFDMA Downlink enabled. A value of 'false' indicates 802.11ax… |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.4 | ColumncLMultiBSSIDProfile11axOfdmaUpLink | read-create | current | This object specifies if 802.11ax OFDMA Uplink is enabled. A value of 'true' indicates 802.11ax OFDMA Uplink enabled. A value of 'false' indicates 802.11ax OFD… |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.5 | ColumncLMultiBSSIDProfile11axMuMIMODownLink | read-create | current | This object specifies if 802.11ax MU-MIMO Downlink is enabled. A value of 'true' indicates 802.11ax MU-MIMO Downlink enabled. A value of 'false' indicates 802.… |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.6 | ColumncLMultiBSSIDProfile11axMuMIMOUpLink | read-create | current | This object specifies if 802.11ax MU-MIMO Uplink is enabled. A value of 'true' indicates 802.11ax MU-MIMO Uplink enabled. A value of 'false' indicates 802.11ax… |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.7 | ColumncLMultiBSSIDProfile11axTwt | read-create | current | This object specifies if 802.11ax Target Wakeup Time(TWT) is enabled. A value of 'true' indicates that 802.11ax TWT is enabled. enabled. A value of 'false' ind… |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.8 | ColumncLMultiBSSIDProfile11axTwtBroadcast | read-create | current | This object specifies if 802.11ax Target Wakeup Time(TWT) Broadcast is enabled. A value of 'true' indicates 802.11ax TWT Broadcast enabled. A value of 'false' … |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.9 | ColumncLMultiBSSIDProfileRowStatus | read-create | current | This is the status column for this row and used to create and delete specific instances of rows in this table. |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.10 | ColumncLMultiBSSIDProfile11beOfdmaDownLink | read-create | current | This object specifies if 802.11be OFDMA Downlink is enabled. A value of 'true' indicates 802.11be OFDMA Downlink enabled. A value of 'false' indicates 802.11be… |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.11 | ColumncLMultiBSSIDProfile11beOfdmaUpLink | read-create | current | This object specifies if 802.11be OFDMA Uplink is enabled. A value of 'true' indicates 802.11be OFDMA Uplink enabled. A value of 'false' indicates 802.11be OFD… |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.12 | ColumncLMultiBSSIDProfile11beMuMIMODownLink | read-create | current | This object specifies if 802.11be MU-MIMO Downlink is enabled. A value of 'true' indicates 802.11be MU-MIMO Downlink enabled. A value of 'false' indicates 802.… |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.13 | ColumncLMultiBSSIDProfile11beMuMIMOUpLink | read-create | current | This object specifies if 802.11be MU-MIMO Uplink is enabled. A value of 'true' indicates 802.11be MU-MIMO Uplink enabled. A value of 'false' indicates 802.11be… |
| 1.3.6.1.4.1.9.9.778.1.1.7.1.14 | ColumncLMultiBSSIDProfile11beOfdmaMultiRU | read-create | current | This object specifies if 802.11be OFDMA Multiple Resource Unit is enabled. A value of 'true' indicates 802.11be OFDMA Multi-RU is enabled. A value of 'false' i… |
| 1.3.6.1.4.1.9.9.778.1.2 | NodeciscoLwappRFGlobalObjects | |||
| 1.3.6.1.4.1.9.9.778.1.2.1 | ScalarcLRFProfileOutOfBoxAPConfig | read-write | current | This object specifies the out of box AP config feature. Enabling this feature will allow any AP that does not have group name configured upon join to controlle… |
| 1.3.6.1.4.1.9.9.778.1.2.2 | ScalarcLRFProfileOutOfBoxAPPersistenceConfig | read-write | current | This object specifies the out of box AP group to be persistent or not. A value of 'true' indicates out-of-box persistence need to be enabled. A value of 'false… |
| 1.3.6.1.4.1.9.9.778.2 | NodeciscoLwappRFMIBConform | |||
| 1.3.6.1.4.1.9.9.778.2.1 | NodeciscoLwappRFMIBCompliances | |||
| 1.3.6.1.4.1.9.9.778.2.1.1 | ComplianceciscoLwappRFMIBCompliance | deprecated | The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. This compliance is deprecated and replaced by ciscoLwappRFMIBComplian… | |
| 1.3.6.1.4.1.9.9.778.2.1.2 | ComplianceciscoLwappRFMIBComplianceVer1 | current | The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. | |
| 1.3.6.1.4.1.9.9.778.2.1.3 | ComplianceciscoLwappRFMIBComplianceVer2 | current | The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. Added ciscoLwappRFConfigGroup2 to add object to raise trap when clien… | |
| 1.3.6.1.4.1.9.9.778.2.1.4 | ComplianceciscoLwappRFMIBComplianceRev3 | current | The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. | |
| 1.3.6.1.4.1.9.9.778.2.1.5 | ComplianceciscoLwappRFMIBComplianceRev4 | current | The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. | |
| 1.3.6.1.4.1.9.9.778.2.1.6 | ComplianceciscoLwappRFMIBComplianceRev5 | current | The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. | |
| 1.3.6.1.4.1.9.9.778.2.1.7 | ComplianceciscoLwappRFMIBComplianceRev6 | current | The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. | |
| 1.3.6.1.4.1.9.9.778.2.1.8 | ComplianceciscoLwappRFMIBComplianceRev7 | current | The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. | |
| 1.3.6.1.4.1.9.9.778.2.2 | NodeciscoLwappRFMIBGroups | |||
| 1.3.6.1.4.1.9.9.778.2.2.1 | GroupciscoLwappRFConfigGroup | deprecated | This collection of objects specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP.This config group ciscoLwappRFConfigGroup… | |
| 1.3.6.1.4.1.9.9.778.2.2.2 | GroupciscoLwappRFConfigGroupVer1 | current | This collection of objects specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP. | |
| 1.3.6.1.4.1.9.9.778.2.2.3 | GroupciscoLwappRFConfigGroup1 | current | This collection of objects specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP. | |
| 1.3.6.1.4.1.9.9.778.2.2.4 | GroupciscoLwappRFGlobalConfigGroup | current | This is the RF global config parameter. | |
| 1.3.6.1.4.1.9.9.778.2.2.5 | GroupciscoLwappRFGroupTrapThresholdConfig | current | This object specifies the configuration of Trap threshold to be configured on the interface of an LWAPP AP. | |
| 1.3.6.1.4.1.9.9.778.2.2.6 | GroupciscoLwappRFConfigGroup3 | current | This object specifies the configuration DCA for RF Profiles. | |
| 1.3.6.1.4.1.9.9.778.2.2.7 | GroupciscoLwappRFConfigGroup4 | current | This object specifies the receiver start of packet threshold for RF Profiles. | |
| 1.3.6.1.4.1.9.9.778.2.2.8 | GroupciscoLwappRFGroupDCAChannelConfig | deprecated | This object specifies the add and remove channels for RF Profiles. | |
| 1.3.6.1.4.1.9.9.778.2.2.9 | GroupciscoLwappRFGroupChannelConfig | current | This object specifies the add and remove channels for RF Profiles. | |
| 1.3.6.1.4.1.9.9.778.2.2.10 | GroupciscoLwappRFConfigGroupExtension1 | current | This object specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP. | |
| 1.3.6.1.4.1.9.9.778.2.2.11 | GroupciscoLwappRFConfigGroup5 | current | This object specifies the receiver start of packet threshold for RF Profiles. | |
| 1.3.6.1.4.1.9.9.778.2.2.12 | GroupciscoLwappRFConfigGroup6 | current | This collection of object specifies the configuration of AirTime Fairness parameters. | |
| 1.3.6.1.4.1.9.9.778.2.2.13 | GroupciscoLwappRFConfigGroup7 | current | This collection of object specifies the removed channel and add channel list information from default DCA channel list for a RF profile | |
| 1.3.6.1.4.1.9.9.778.2.2.14 | GroupciscoLwappRFConfigGroup8 | current | This collection of objects specifies the 802.11ax OBSS PD spatial reuse configurations for RF Profiles. | |
| 1.3.6.1.4.1.9.9.778.2.2.15 | GroupciscoLwappRFConfigGroup9 | current | This collection of objects specifies the neighbor discovery mode for a RF profile | |
| 1.3.6.1.4.1.9.9.778.2.2.16 | GroupciscoLwappRFConfigGroup10 | current | This collection of objects specifies the 802.11ax Broadcast Probe response, FILS Discovery and PSC bias configurations for RF Profiles. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CiscoLwappRFApDataRates | INTEGER { disabled(0), supported(1), mandatoryRate(2), notApplicable(3) } | current | This field indicates the data rates supported by an AP 'disabled' The rate is not supported by the AP 'supported' The rate is supported by the AP 'mandatoryRate' The rate is required by the AP 'notApplicable' The rate i… |