CISCO-METRO-PHY-MIB
69 objects
This MIB module defines the managed objects for physical layer related interface configurations and objects for the protocol specific error counters for DWDM optical switches. This MIB contains three groups. The first group, cmPhyIf group, handles the physical layer related interface configurations. The cmPhyIfTable has objects for configuring protocol, rate, error monitoring, loopback mode and safety features like OFC (Open Fibre Control), laser safety control and forward laser control. The second group, cmPhyStatistics group, represents the counters that collect error statistics on the received data traffic for all protocols except SONET. The error statistics for SONET are covered in the SONET-MIB. The third group, cmPhySonetSectionTrace group, provides objects for section trace monitoring on SONET/SDH interfaces.
Imported Objects
| CISCO-SMI | ciscoExperiment |
| IF-MIB | ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Integer32 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.10.69 | IdentityciscoMetroPhyMIB | This MIB module defines the managed objects for physical layer related interface configurations and objects for the protocol specific error counters for DWDM o… | ||
| 1.3.6.1.4.1.9.10.69.1 | NodeciscoMetroPhyMIBObjects | |||
| 1.3.6.1.4.1.9.10.69.1.1 | NodecmPhyIf | |||
| 1.3.6.1.4.1.9.10.69.1.1.1 | TablecmPhyIfTable | not-accessible | current | This table allows physical layer related interface configurations on an interface. |
| 1.3.6.1.4.1.9.10.69.1.1.1.1 | RowcmPhyIfEntry | not-accessible | current | A collection of objects for configuration on an interface. |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.1 | ColumncmPhyIfMode | read-write | current | This object allows the management client to configure the mode of operation for the client interface modules. When in 2R mode, there is no protocol type, clock… |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.2 | ColumncmPhyIfProtocol | read-write | current | This object is used to specify the protocol of the data carried over the client side interface. This object applies to linecards which support a variety of pro… |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.3 | ColumncmPhyIfClockRate | read-write | current | This object allows the management client to set the clock rate across the client side interface. Due to hardware limitations, all values may not be supported. … |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.4 | ColumncmPhyIfMonitor | read-write | current | This object allows the management client to enable monitoring of the error counters on an interface, by writing a value of 'true' to this object. To bypass the… |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.5 | ColumncmPhyIfLoopback | read-write | current | This object allows the management client to configure loopback for the client side or trunk side interfaces. 'noLoop' - No Loopback present. 'diagnosticLoop' -… |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.6 | ColumncmPhyIfOFC | read-write | current | This object allows the management client to enable OFC(Open Fibre Control) safety protocol for the client side interfaces, by writing a 'true' value to this ob… |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.7 | ColumncmPhyIfLaserSafetyControl | read-write | deprecated | This object allows the management client to enable laser safety control feature on the trunk side interfaces by writing a true value to this object. If laser s… |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.8 | ColumncmPhyIfForwardLaserControl | read-write | deprecated | This object allows the management client to enable forward laser control on the client or trunk side interfaces by writing a true value to this object. If forw… |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.9 | ColumncmPhyIfTxBufferSize | read-write | current | This object applies when circuit emulation of the client protocol is used. It allows the management client to configure the size of the transmit buffer on the … |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.10 | ColumncmPhyIfAutoNegotiation | read-write | current | This object allows the management client to enable auto negotiation signaling on the client side interface, by writing a 'true' value to this object. A 'false'… |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.11 | ColumncmPhyIfTransType | read-only | current | This object is used to identify the physical layer medium used for carrying data. For non-relevant interfaces, this value is 'unknown'. |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.12 | ColumncmPhyIfRate | read-write | current | This object is used to specify the rate of the interface. The value of 'unknown' implies that this object does not apply to this interface. |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.13 | ColumncmPhyIfNegotiatedRate | read-only | current | This object is used to identify the current rate of the interface after the auto negotation. This object is valid only if the object cmPhyIfRate is configured … |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.14 | ColumncmPhyIfOverSubscription | read-write | current | Oversubscription allows the user to carry multiple clients over the trunk to efficiently utilize the trunk bandwidth. This object allows the management client … |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.15 | ColumncmPhyIfClientSubrate | read-write | current | This object allows the management client to specify the subrate bandwidth of the oversubscribed trunk which carries this client. A value of 0 implies that this… |
| 1.3.6.1.4.1.9.10.69.1.1.1.1.16 | ColumncmPhyIfClientSubrateLock | read-write | current | This object allows the management client to lock the subrate bandwidth on an interface, by writing a value of 'true' to this object. A 'false' value would disa… |
| 1.3.6.1.4.1.9.10.69.1.2 | NodecmPhyStatistics | |||
| 1.3.6.1.4.1.9.10.69.1.2.1 | TablecmPhyStatisticsTable | not-accessible | current | This table contains the cumulative error statistics being collected for the different medium types, except SONET, on the client side and an object for the opti… |
| 1.3.6.1.4.1.9.10.69.1.2.1.1 | RowcmPhyStatisticsEntry | not-accessible | current | An entry in the cmPhyStatisticsTable. |
| 1.3.6.1.4.1.9.10.69.1.2.1.1.1 | ColumncmPhyRxPower | read-only | deprecated | This object gives the optical power level received on the trunk side interface. The actual value of the power level received on the interface is the value of t… |
| 1.3.6.1.4.1.9.10.69.1.2.1.1.2 | ColumncmPhyRxCVRD | read-only | current | This object represents the lower word value of the counter associated with the number of code violations and running disparity errors encountered, in the recei… |
| 1.3.6.1.4.1.9.10.69.1.2.1.1.3 | ColumncmPhyRxCVRDOverflow | read-only | current | This object represents the high word value of the counter associated with the number of code violations and running disparity errors encountered, in the receiv… |
| 1.3.6.1.4.1.9.10.69.1.2.1.1.4 | ColumncmPhyHCRxCVRD | read-only | current | This object represents the counter associated with the number of code violations and running disparity errors encountered, in the receive direction. This is a … |
| 1.3.6.1.4.1.9.10.69.1.2.1.1.5 | ColumncmPhyRxHEC | read-only | deprecated | This object represents the lower word value of the counter associated with the number of CDL HEC errors encountered, in the receive direction. This object has … |
| 1.3.6.1.4.1.9.10.69.1.2.1.1.6 | ColumncmPhyRxHECOverflow | read-only | deprecated | This object represents the high word value of the counter associated with the number of CDL HEC errors encountered, in the receive direction. This object has a… |
| 1.3.6.1.4.1.9.10.69.1.2.1.1.7 | ColumncmPhyHCRxHEC | read-only | deprecated | This object represents the counter associated with the number of CDL HEC errors encountered, in the receive direction. This object has a valid value only if th… |
| 1.3.6.1.4.1.9.10.69.1.2.1.1.8 | ColumncmPhyRxCRC | read-only | current | This object represents the lower word value of the counter associated with CRC errors. This object has a valid value only for interfaces that provide CRC error… |
| 1.3.6.1.4.1.9.10.69.1.2.1.1.9 | ColumncmPhyRxCRCOverflow | read-only | current | This object represents the higher word value of the counter associated with CRC errors. This object has a valid value only for interfaces that provide CRC erro… |
| 1.3.6.1.4.1.9.10.69.1.2.1.1.10 | ColumncmPhyHCRxCRC | read-only | current | This object represents the counter associated with CRC errors. This object has a valid value only for interfaces that provide CRC error monitoring. This is a H… |
| 1.3.6.1.4.1.9.10.69.1.2.1.1.11 | ColumncmPhyTxEncapFarEndPktErrors | read-only | current | This object represents the lower word value of the counter associated with ingress error indications from the far end of an Ethernet network, where an ESCON st… |
| 1.3.6.1.4.1.9.10.69.1.2.1.1.12 | ColumncmPhyTxEncapFarEndPktErrOverflow | read-only | current | This object represents the higher word value of the counter associated with ingress error indications from the far end of an Ethernet network, where an ESCON s… |
| 1.3.6.1.4.1.9.10.69.1.2.1.1.13 | ColumncmPhyHCTxEncapFarEndPktErrors | read-only | current | This object represents the counter associated with ESCON ingress error indications from the far end of an Ethernet network, where an ESCON stream is encapsulat… |
| 1.3.6.1.4.1.9.10.69.1.3 | NodecmPhySonetSectionTrace | |||
| 1.3.6.1.4.1.9.10.69.1.3.1 | TablecmPhySonetSectionTraceTable | not-accessible | current | This table provides objects for monitoring the J0 bytes of a SONET or SDH section. |
| 1.3.6.1.4.1.9.10.69.1.3.1.1 | RowcmPhySonetSectionTraceEntry | not-accessible | current | An entry in the cmPhySonetSectionTraceTable is created when the value of the cmPhyIfProtocol object is set to 'sonet' and the value of cmPhyIfMonitor is set to… |
| 1.3.6.1.4.1.9.10.69.1.3.1.1.1 | ColumncmPhySonetSectionTraceReceived | read-only | current | This object displays the SONET or SDH section trace bytes received at the interface. |
| 1.3.6.1.4.1.9.10.69.1.3.1.1.2 | ColumncmPhySonetSectionTraceExpected | read-write | current | This object defines the SONET or SDH section trace bytes to be expected at the interface. The default value of this object will be a zero length string. |
| 1.3.6.1.4.1.9.10.69.3 | NodeciscoMetroPhyMIBConformance | |||
| 1.3.6.1.4.1.9.10.69.3.1 | NodeciscoMetroPhyMIBCompliances | |||
| 1.3.6.1.4.1.9.10.69.3.1.1 | CompliancecmPhyMIBCompliance | read-only | deprecated | The compliance statement for platforms that monitor the operating status with respect to error counters, for the physical layer. |
| 1.3.6.1.4.1.9.10.69.3.1.2 | CompliancecmPhyMIBCompliance2 | read-only | deprecated | The compliance statement for platforms that monitor the operating status with respect to error counters, for the physical layer. |
| 1.3.6.1.4.1.9.10.69.3.1.3 | CompliancecmPhyMIBCompliance3 | read-only | deprecated | The compliance statement for platforms that monitor the operating status with respect to error counters, for the physical layer. |
| 1.3.6.1.4.1.9.10.69.3.1.4 | CompliancecmPhyMIBComplianceRev4 | read-only | deprecated | The compliance statement for platforms that monitor the operating status with respect to error counters, for the physical layer. |
| 1.3.6.1.4.1.9.10.69.3.1.5 | CompliancecmPhyMIBComplianceRev5 | read-only | deprecated | The compliance statement for platforms that monitor the operating status with respect to error counters, for the physical layer. |
| 1.3.6.1.4.1.9.10.69.3.1.6 | CompliancecmPhyMIBComplianceRev6 | read-only | current | The compliance statement for platforms that monitor the operating status with respect to error counters, for the physical layer. |
| 1.3.6.1.4.1.9.10.69.3.2 | NodeciscoMetroPhyMIBGroups | |||
| 1.3.6.1.4.1.9.10.69.3.2.1 | GroupcmPhyIfGroup | deprecated | The collection of objects to allow configurations and give information related to the physical layer characteristics of an interface. | |
| 1.3.6.1.4.1.9.10.69.3.2.2 | GroupcmPhyStatisticsGroup | deprecated | The collection of objects used to monitor the protocol error counters on the client side and the power level received on the trunk side. | |
| 1.3.6.1.4.1.9.10.69.3.2.3 | GroupcmPhySonetSectionTraceGroup | current | The objects used for monitoring the SONET section trace bytes. | |
| 1.3.6.1.4.1.9.10.69.3.2.4 | GroupcmPhyIf2Group | current | The collection of objects to allow configurations and give information related to the physical layer characteristics of an interface. | |
| 1.3.6.1.4.1.9.10.69.3.2.5 | GroupcmPhyCVRDErrorsGroup | current | The collection of objects used to monitor the code violation and running disparity error counters. | |
| 1.3.6.1.4.1.9.10.69.3.2.6 | GroupcmPhyCRCErrorsGroup | current | The collection of objects used to monitor CRC error counters. | |
| 1.3.6.1.4.1.9.10.69.3.2.7 | GroupcmPhyEncapFarEndPktErrorsGroup | current | The collection of objects used to monitor the far end ingress error indication counters for Ethernet- encapsulated ESCON streams. | |
| 1.3.6.1.4.1.9.10.69.3.2.8 | GroupcmPhyIfTxBufferSizeGroup | current | The collection of objects used to control size of transmit buffer. | |
| 1.3.6.1.4.1.9.10.69.3.2.9 | GroupcmPhyIfAutoNegGroup | current | The collection of objects used to control auto negotiation behavior. | |
| 1.3.6.1.4.1.9.10.69.3.2.10 | GroupcmPhyIfGroupSup1 | current | The object that gives information related to transmission types on the client interface. | |
| 1.3.6.1.4.1.9.10.69.3.2.11 | GroupcmPhyIfRateGroup | current | The collection of objects that are used to retrieve and configure the various interface rates. | |
| 1.3.6.1.4.1.9.10.69.3.2.12 | GroupcmPhyIfClientOvsGroup | current | The collection of objects to allow the oversubscription configurations on an interface. | |
| 1.3.6.1.4.1.9.10.69.3.2.13 | GroupcmPhyIfClientSubrateGroup | current | The collection of objects to allow the configurations related to the subrating on an interface. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CmNegotiatedRateType | INTEGER { notApplicable(1), negotiating(2), oneGbps(3), twoGbps(4), fourGbps(5), tenGbps(6) } | current | An integer value that identifies the current rate of the interface after the auto negotiation. The value 'notApplicable' indicates this object is not applicable for the interface. The value 'negotiating' indicates the i… |
| CmRateType | INTEGER { unknown(1), auto(2), oneGbps(3), twoGbps(4), fourGbps(5), tenGbps(6) } | current | An integer value that identifies the rate of the interface. The value 'unknown' indicates the rate of the interface is not known. The value 'auto' indicates the rate of the interface is auto. The client interface will a… |
| ProtocolType | INTEGER { other(1), unknown(2), gigabitEthernet(3), tenGigabitEthernet(4), fibreChannel(5), ficon(6), escon(7), sonet(8), sdh(9), sysplexIscCompatibility(10), sysplexIscPeer(11), sysplexTimerEtr(12), sysplexTimerClo(13), fastEthernet(14), fddi(15), e1(16), t1(17), e3(18), t3(19), dvb(20), sdi(21), its(22) } | current | An integer value that identifies the protocol used across an interface. The value 'e1' indicates an interface that implements the physical layer of E1. The value 't1' indicates an interface that implements the physical … |
| TransmissionType | INTEGER { unknown(1), copper(2), optical(3) } | current | An integer value that identifies the physical layer medium used across an interface. The value 'unknown' indicates the physical layer medium is not known. The value 'copper' indicates the physical layer medium is copper… |
| TriValue | INTEGER { true(1), false(2), notApplicable(3) } | current | A three codepoint value. |