CISCO-MGX82XX-DSX1-MIB
104 objects
The MIB module to configure DS1/E1 interface objects. This mib also contains the alarm configuration of DS1/E1 interfaces. This mib is supported in T1/E1 service modules.
Imported Objects
| BASIS-MIB | dsx1Line |
| CISCOWAN-SMI | ciscoWan |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY OBJECT-TYPE |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.110.4.3.1.1 | Nodedsx1CnfGrp | |||
| 1.3.6.1.4.1.351.110.4.3.1.1.1 | Tabledsx1CnfGrpTable | not-accessible | current | The DS1/E1 Configuration table. The table size is given by the value of lineNumofValidEntries |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1 | Rowdsx1CnfGrpEntry | not-accessible | current | An entry in the DS1 Configuration table. |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.1 | ColumnlineNum | read-only | current | This object is the identifier of a DS1/E1 Interface on a managed device. If there is an ifEntry that is directly associated with this and only this DS1/E1 inte… |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.2 | ColumnlineConnectorType | read-write | current | This variable indicates the connector as well as the backcard type. 1 = T1; 2 = E1. This field is set to unused(4) for FRSM-VHS cards. |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.3 | ColumnlineEnable | read-write | current | This variable disables, enables or modifies a line 1 - disable 2 - enable 3 - modify In FRSM-2CT3, if the DS3 line is enabled, then the DS1 channels for that l… |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.4 | ColumnlineType | read-write | current | This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reaso… |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.5 | ColumnlineCoding | read-write | current | This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. dsx1JBZS(1): refers the J… |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.6 | ColumnlineLength | read-write | current | This is not a standard RFC 1407 DS1 variable, it is specific to BASIS implementation. It specifies the line length: 1 - 0 to 110 ft (T1 line only) 2 - 110 to 2… |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.7 | ColumnlineXmtClockSource | read-write | current | The source of Transmit Clock. loopTiming(1): indicates that the recovered receive clock is used as the transmit clock. localTiming(2): indicates that a local c… |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.8 | ColumnlineLoopbackCommand | read-write | current | This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should return badValue in response to a reque… |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.9 | ColumnlineSendCode | read-write | current | This variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: dsx1SendNoCode sending looped or normal data… |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.10 | ColumnlineUsedTimeslotsBitMap | read-only | current | Bit map of used DS0 for this line. |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.11 | ColumnlineLoopbackCodeDetection | read-write | current | Enable detection of line Loopback Codes |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.12 | ColumnlineBERTEnable | read-write | current | This variable enables Bit Error Rate Testing(BERT). |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.13 | ColumnlineBERTPattern | read-write | current | This variable determines BERT pattern to transmit |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.14 | ColumnlineBERTResult | read-write | current | This shows the result of the BERT. |
| 1.3.6.1.4.1.351.110.4.3.1.1.1.1.15 | ColumnbERTResultClrButton | read-write | current | This clears the result of the BERT. |
| 1.3.6.1.4.1.351.110.4.3.1.1.2 | ScalarlineNumofValidEntries | read-only | current | The number of DS1 configuration entries (regardless of their current configuration) in the dsx1CnfGrpTable. |
| 1.3.6.1.4.1.351.110.4.3.1.2 | Nodedsx1AlmCnfGrp | |||
| 1.3.6.1.4.1.351.110.4.3.1.2.1 | Tabledsx1AlmCnfGrpTable | not-accessible | current | The DS1 interface alarm configuration table. |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1 | Rowdsx1AlmCnfGrpEntry | not-accessible | current | An entry in the DS1 Alarm Configuration table. |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.1 | ColumnalmCnfLineNum | read-only | current | This object identifies the DS1/E1 interface. The value for this object must be same as the value of lineNum from dsx1CnfGrpTable. |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.2 | ColumnredSeverity | read-write | current | This variable is used to setup the severity of RED alarm. So when RED alarm is detected by the card, an alarm with appropriate severity status will be sent. |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.3 | ColumnrAISeverity | read-write | current | This variable is used to setup the severity of RAI alarm. So when LOS alarm is detected the card, an alarm with appropriate severity status will be sent. |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.4 | ColumnnEAlarmUpCount | read-write | current | This parameter specifies the integration counter, the local alarms are LOS and LOF. Default value is 6 and update counter every 10 ms to reach the threshold se… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.5 | ColumnnEAlarmDownCount | read-write | current | This parameter specifies the integration counter, the Near-End alarms are LOS and LOF. Default value is 1 and update counter every 10 ms to reach 0. This is th… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.6 | ColumnnEAlarmThreshold | read-write | current | The value set in this object determines the value to declare Near-End alarm. A count of 1500 gives 2.5 sec to declare LOS with an up count value of 6. |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.7 | ColumnfEAlarmUpCount | read-write | current | This parameter specifies the integration counter, the Far-End alarms are AIS and YEL. Default value is 6 and update counter 10 ms to reach the threshold set in… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.8 | ColumnfEAlarmDownCount | read-write | current | This parameter specifies the integration counter, the Far-End alarms are AIS and YEL. Default value is 1 and update counter every 10 ms to reach 0. This is the… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.9 | ColumnfEAlarmThreshold | read-write | current | The value set in this object determines the value to declare Far-End alarm. A count of 1500 gives 2.5 secs to declare LOS with an up count value of 6. |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.10 | ColumnstatisticalAlarmSeverity | read-write | current | This variable is used to setup the severity of Statistical alarm. So when any statistical alarm is detected by the card, an alarm with appropriate severity sta… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.11 | ColumnlCV15MinThreshold | read-write | current | Code Violation - is the occurrence of a received CRC-6 code that is not identical to the corresponding locally. calculated code. The value set in this object d… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.12 | ColumnlCV24HrThreshold | read-write | current | Code Violation - is the occurence of a received CRC-6 code that is not identical to the corresponding locally. The value set in this object determines the valu… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.13 | ColumnlES15MinThreshold | read-write | current | Errored Second - is any second with at least one code violation. The value set in this object determines the value which when exceeded in a 15 minute window ca… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.14 | ColumnlES24HrThreshold | read-write | current | Errored Second - is any second with at least one code violation. The value set in this object determines the value which when exceeded in a sliding 24 hour win… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.15 | ColumnlSES15MinThreshold | read-write | current | Severely Errored Second - is any second with 15 or more code violations. The value set in this object determines the value which when exceeded in a 15 minute w… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.16 | ColumnlSES24HrThreshold | read-write | current | Severely Errored Second - is any second with 15 or more code violations. The value set in this object determines the value which when exceeded in a sliding 24 … |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.17 | ColumncRC15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.18 | ColumncRC24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.19 | ColumncRCES15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.20 | ColumncRCES24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.21 | ColumncRCSES15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.22 | ColumncRCSES24HrThreshold | read-write | current | The value set in this object determines the value when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.23 | ColumnsEFS15MinThreshold | read-write | current | Severely Errored Framing Second - is a count of one-second intervals containing one or more SEF events. The value set in this object determines the value which… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.24 | ColumnsEFS24HrThreshold | read-write | current | Severely Errored Framing Second - is a count of one-second intervals containing one or more SEF events. The value set in this object determines the value which… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.25 | ColumnaISS15MinThreshold | read-write | current | Alarm Indication Signal Second - is a count of one-second intervals containing one or more incoming AIS. The value set in this object determines the value whic… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.26 | ColumnaISS24HrThreshold | read-write | current | Alarm Indication Signal Second - is a count of one-second intervals containing one or more incoming AIS. The value set in this object determines the value whic… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.27 | ColumnuAS15MinThreshold | read-write | current | Unavailable Second - is a count of seconds during which the DS1 Layer service is unavailable. The value set in this object determines the value which when exce… |
| 1.3.6.1.4.1.351.110.4.3.1.2.1.1.28 | ColumnuAS24HrThreshold | read-write | current | Unavailable Second - is a count of seconds during which the DS1 Layer service is unavailable. The value set in this object determines the value which when exce… |
| 1.3.6.1.4.1.351.110.4.3.1.3 | Nodedsx1AlmGrp | |||
| 1.3.6.1.4.1.351.110.4.3.1.3.1 | Tabledsx1AlmGrpTable | not-accessible | current | The DS1 interface alarm configuration table. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1 | Rowdsx1AlmGrpEntry | not-accessible | current | An entry in the DS1 Alarm table. Each entry represents the current, 15 minute and 24 Hour bucket intervals for different performance parameters. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.1 | ColumnalmLineNum | read-only | current | This object identifies the DS1/E1 interface. The value for this object must be same as the value of lineNum from dsx1CnfGrpTable. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.2 | ColumnlineAlarmState | read-only | current | This variable is a bitmap of the DSX1 Line Alarms. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alarm 0 Receiving R… |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.3 | ColumnlineStatisticalAlarmState | read-only | current | This variable is a bitmap of the DSX1 Line Statistical Alarms. A value of zero indicates no alarms. Itemized below are the individual alarm bits: BitPosition A… |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.4 | ColumnlCVCurrent | read-only | current | This counter counts the number of Line code violations encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.5 | ColumnlCV15MinBucket | read-only | current | The counter associated with the number of Line code violations in the last 15 minute period encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.6 | ColumnlCV24HrBucket | read-only | current | The counter associated with the number of Line code violations in the last 24 hour period encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.7 | ColumnlESCurrent | read-only | current | This counter counts the number of Line code violations Errored Seconds encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.8 | ColumnlES15MinBucket | read-only | current | This counter counts the number of Line code violations Errored Seconds in the last 15 minutes encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.9 | ColumnlES24HrBucket | read-only | current | This counter counts the number of Line code violations Errored Seconds in the last 24 hours encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.10 | ColumnlSESCurrent | read-only | current | This counter counts the number of Line code violations Severely Errored Seconds encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.11 | ColumnlSES15MinBucket | read-only | current | This counter counts the number of LCV Severely Errored Seconds in the last 15 minutes encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.12 | ColumnlSES24HrBucket | read-only | current | This counter counts the number of LCV Severely Errored Seconds in the last 24 hours encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.13 | ColumncRCCurrent | read-only | current | This counter counts the number of P Bit code violations encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.14 | ColumncRC15MinBucket | read-only | current | This counter counts the number of P Bit code violations in the last 15 minutes encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.15 | ColumncRC24HrBucket | read-only | current | This counter counts the number of P Bit code violations in the last 24 hours encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.16 | ColumncRCESCurrent | read-only | current | This counter counts the number of PCV Errored Seconds encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.17 | ColumncRCES15MinBucket | read-only | current | This counter counts the number of PCV Errored Seconds in the last 15 minutes encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.18 | ColumncRCES24HrBucket | read-only | current | This counter counts the number of PCV Errored Seconds in the last 24 hours encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.19 | ColumncRCSESCurrent | read-only | current | This counter counts the number of P Bit code violations Severely Errored Seconds encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.20 | ColumncRCSES15MinBucket | read-only | current | This counter counts the number of PCV Severely Errored Seconds in the last 15 minutes encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.21 | ColumncRCSES24HrBucket | read-only | current | This counter counts the number of PCV Severely Errored Seconds in the last 24 hours encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.22 | ColumnsEFSCurrent | read-only | current | This counter counts the number of Severely Errored Framing Seconds encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.23 | ColumnsEFS15MinBucket | read-only | current | This counter counts the number of Severely Errored Framing Seconds in the last 15 minutes encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.24 | ColumnsEFS24HrBucket | read-only | current | This counter counts the number of Severely Errored Framing Seconds in the last 24 hours encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.25 | ColumnaISSCurrent | read-only | current | This counter counts the number of AIS Severely Errored Seconds encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.26 | ColumnaISS15MinBucket | read-only | current | This counter counts the number of AIS Severely Errored Seconds in the last 15 minutes encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.27 | ColumnaISS24HrBucket | read-only | current | This counter counts the number of AIS Severely Errored Seconds in the last 24 hours encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.28 | ColumnuASCurrent | read-only | current | This counter counts the number of Unavailable Seconds encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.29 | ColumnuAS15MinBucket | read-only | current | This counter counts the number of Unavailable Seconds in the last 15 minutes encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.30 | ColumnuAS24HrBucket | read-only | current | This counter counts the number of Unavailable Seconds in the last 24 hours encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.31 | ColumnpercentEFS | read-only | current | This counter counts the %LCV Error Free Seconds. |
| 1.3.6.1.4.1.351.110.4.3.1.3.1.1.32 | ColumnalarmClrButton | read-write | current | This variable is used to clear all the alarms for the line. 1 = No action 2 = Clear alarm |
| 1.3.6.1.4.1.351.110.4.3.1.4 | Nodedsx1CntGrp | |||
| 1.3.6.1.4.1.351.110.4.3.1.4.1 | Tabledsx1CntGrpTable | not-accessible | current | The DS1 Counter table. This table contains statistics since the system was up or last re-initialization. |
| 1.3.6.1.4.1.351.110.4.3.1.4.1.1 | Rowdsx1CntGrpEntry | not-accessible | current | An entry in the DS1 counter table. |
| 1.3.6.1.4.1.351.110.4.3.1.4.1.1.1 | ColumncntLineNum | read-only | current | This object identifies the DS1/E1 interface. The value for this object must be same as the value of lineNum from dsx1CnfGrpTable. |
| 1.3.6.1.4.1.351.110.4.3.1.4.1.1.2 | ColumnrcvLOSCount | read-only | current | The number of times the Loss of Signal was detected with or without integrating to LOS alarm. |
| 1.3.6.1.4.1.351.110.4.3.1.4.1.1.3 | ColumnrcvOOFCount | read-only | current | The number of times the Out of Frame was detected with or without integrating to OOF alarm. |
| 1.3.6.1.4.1.351.110.4.3.1.4.1.1.4 | ColumnrcvRAICount | read-only | current | The number of times Yellow Alarms was detected with or without integrating to RAI alarm. |
| 1.3.6.1.4.1.351.110.4.3.1.4.1.1.5 | ColumnrcvFECount | read-only | current | The number of Framing Pattern Errors encountered by a DS1 interface. |
| 1.3.6.1.4.1.351.110.4.3.1.4.1.1.6 | ColumncounterClearButton | read-write | current | This variable is used to clear all the counters. |
| 1.3.6.1.4.1.351.150.58 | IdentityciscoMgx82xxDsx1MIB | The MIB module to configure DS1/E1 interface objects. This mib also contains the alarm configuration of DS1/E1 interfaces. This mib is supported in T1/E1 servi… | ||
| 1.3.6.1.4.1.351.150.58.2 | NodecmDsx1MIBConformance | |||
| 1.3.6.1.4.1.351.150.58.2.1 | NodecmDsx1MIBGroups | |||
| 1.3.6.1.4.1.351.150.58.2.1.1 | GroupcmDsx1GeneralGroup | current | The collection of objects used for DS1/E1 interfaces. | |
| 1.3.6.1.4.1.351.150.58.2.1.2 | GroupcmDsx1ConfGroup | current | The collection of objects used for DS1/E1 interface configuration. | |
| 1.3.6.1.4.1.351.150.58.2.1.3 | GroupcmDsx1CountGroup | current | The collection of objects related to DS1/E1 statistics. | |
| 1.3.6.1.4.1.351.150.58.2.1.4 | GroupcmDsx1AlarmConfGroup | current | The collection of objects used for DS1/E1 Alarm threshold configuration. | |
| 1.3.6.1.4.1.351.150.58.2.1.5 | GroupcmDsx1AlarmGroup | current | The collection of objects used for DS1/E1 Alarm configuration. | |
| 1.3.6.1.4.1.351.150.58.2.2 | NodecmDsx1MIBCompliances | |||
| 1.3.6.1.4.1.351.150.58.2.2.1 | CompliancecmDsx1Compliance | current | The compliance statement for objects related to DS1/E1 mib. |