CISCO-MGX82XX-DSX3-MIB
233 objects
The MIB Module for DS3/E3 interface configuration , statistics and Alarm configuration. This MIB is supported in T3/E3 service modules in MGX products. Some of the T3/E3 service modules(Cards) are: PXM1 : Processor Switch Module. CESM-T3E3: Circuit Emulation Service Module FRSM-VHS : Frame Relay Service Module. Includes T3 and Channelized T3 categories. FRSM-2CT3: Channelized FRSM Module SRM-3T3 : Service Resource Module Terminologies Used : SDH : SONET Digital Hierarchy PLCP : Physical Layer Convergence Procedure. BERT : Bit Error Rate Testing. FEAC : Far End Alarm Code. OOF : Out Of Frame. AIS : Alarm Indication Signal. LOF : Loss Of Frame. RAI : Remote Alarm Indication. HCS : Header Check Sequence HEC : Header Error Control MA byte : Maintenance and Adaptation byte Tx MA Byte: This is explained in ITU-T G.832 This Byte contains following fields: Payload type Payload dependent bits Timing maker bit Rx MA Byte: This is explained in ITU-T G.832 This Byte contains following fields: Payload type Timing maker bit
Imported Objects
| BASIS-MIB | dsx3Framing dsx3Line |
| CISCOWAN-SMI | ciscoWan |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.110.4.4.1.1 | Nodedsx3Config | |||
| 1.3.6.1.4.1.351.110.4.4.1.1.1 | TablecwDsx3ConfigTable | not-accessible | current | The DS3/E3 Configuration table. There is one row for each DSX3 port in the system. The table size (number of rows) is given by the value of dsx3LineNumOfValidE… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1 | RowcwDsx3ConfigEntry | not-accessible | current | An entry in the DSX3 Configuration table. |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.1 | Columndsx3LineNum | read-only | current | This object is the identifier of a DS3/E3 Interface on a managed device. The range supported depends upon the type of the card(controller card, service module)… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.2 | ColumncwDsx3LineType | read-write | current | This variable indicates the variety of DS3 C-bit or E3 application implementing this interface. The type of interface affects the interpretation of the usage a… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.3 | ColumncwDsx3LineCoding | read-write | current | This variable describes the variety of Zero Code Suppression used on this interface, which in turn affects a number of its characteristics. dsx3B3ZS and e3HDB3… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.4 | ColumncwDsx3LineLength | read-write | current | This object specifies the length of the DS3 Line. This object provides information for line build out circuitry if it exists and can use this object to adjust … |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.5 | Columndsx3LineOOFCriteria | read-write | current | This object specifies the out of frame decision criteria. OOF is declared when errors are detected in the framing octets for four consecuitive frames. fBits3Of… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.6 | Columndsx3LineAIScBitsCheck | read-write | current | If check C-Bits options is chosen then AIS is declared when 1010 pattern is found and C-Bits are all zero. In the other case an AIS condition is declared when … |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.7 | Columndsx3LineLoopbackCommand | read-write | current | This variable represents the loopback configuration of the DS3/E3 interface. The values mean: dsx3NoLoop Not in the loopback state. A device that is not capabl… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.8 | Columndsx3LineRcvFEACValidation | read-write | current | This entry specifies the FEAC code validation criteria. fFEACCodes4Of5(1) : a valid FEAC code is declared if 4 of 5 codes match. fFEACCodes8Of10(2): a valid FE… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.9 | Columndsx3LineXmtFEACCode | read-write | current | This variable indicates what bit-oriented code to transmit over the far-end alarm and control (FEAC) channel. The values mean: dsx3SendNoCode sending looped or… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.10 | Columndsx3LineBERTEnable | read-write | current | This object enables/disables the BERT function on an interface. The possible values are : disabled(1): disables port BERT functionality enabled (2): enables po… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.11 | Columndsx3LineBERTPattern | read-write | current | This object defines the test bit pattern to be used for BERT. The possible values are : Repetitive Patterns allZero(1): All Zeroes(Continuous spaces). This is … |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.12 | Columndsx3LineBERTResult | read-only | current | Result of BERT Test. The value in this object is not applicable if dsx3LineBERTEnable is set to disabled(1). |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.13 | Columndsx3BERTResultClrButton | read-write | current | Setting this object to clear(2) causes the BERT result field to get cleared. |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.14 | Columndsx3TrailTraceOption | read-write | current | This object is used for enabling/disabling G.832 Trail Trace. The trail trace is used to repetitively transmit a trail access point identifier so that a trail … |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.15 | Columndsx3TxTrailTrace | read-write | current | This object is used for specifying the data to be used for G.832 Trail Trace ID/String. This object is applicable only for E3 interfaces with G.832 framing. Th… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.16 | Columndsx3RxTrailTrace | read-only | current | Received G.832 Trail Trace string. The format of the value is: First byte indicates CRC-7(frame start marker). Bytes 2-6 (ASCII) [Byte 1-5 of this object] Byte… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.17 | Columndsx3TxTimingMarker | read-write | current | Transmitted timing marker bit in G.832 MA byte. This object can be set to traceable(1) to indicate that the timing source is traceable to a primary reference c… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.18 | Columndsx3RxTimingMarker | read-write | current | Received timing marker bit in G.832 MA byte. This object can be set to traceable(1) to indicate that the timing source is tracable to a primary reference clock… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.19 | Columndsx3TxPayloadType | read-write | current | This object specifies the G.832 payload type for transmit data. The possible values are : unequipped (1): not carrying any payload equipped (2): Equipped,non-s… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.20 | Columndsx3RxPayloadType | read-only | current | Received payload type field in G.832 byte The possible values are : unequipped (1): not carrying any payload equipped (2): Equipped,non-specific atm (3): ATM s… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.21 | Columndsx3TxTumf | read-only | current | This object contains the value of Tributary Multiframe Indicator(bits 6 and 7 of MA byte) in case of TU-1xs mapping. This is not supported in FRSM-VHS and CESM… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.22 | Columndsx3RxTumf | read-only | current | This object contains the value of Tributary Multiframe Indicator(bits 6 and 7 of MA byte) in case of TU-1xs mapping. This object is not supported in FRSM-VHS a… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.23 | Columndsx3LineEnable | read-write | current | This object is used for enabling/disabling an interface and modifying the interface configuration. The possible values are: disable (1): Interface is administr… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.24 | Columndsx3FarEndLoopbkLineNum | read-write | current | Specify which DS1 or DS3 line in the far-end for the loopback testing. For CESM-T3/E3, only ds3line(30) is valid. |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.25 | Columndsx3LineXmtClockSrc | read-write | current | The source of the transmit clock. backplaneClk(2) : clock source is from the backplane. recoverClk (3) : clock source is derived from another t3 interface. loc… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.26 | Columndsx3FarEndLoopbkLineStatus | read-only | current | This is a bitmap of the DSX3 FarEnd line loopback status bits Bit Position Loopback indicator 1 DS1 Line 1 2 DS1 Line 2 3 DS1 Line 3 4 DS1 Line 4 5 DS1 Line 5 … |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.27 | Columndsx3LineEqualizer | read-write | current | This object indicates whether the internal equalizer is being used or bypassed. Set this value depending on the line equipment to which the receiver is attache… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.28 | Columndsx3NearEndLoopbkLineStatus | read-only | current | This is a bitmap of the DSX3 NearEnd line loopback status bits BitPosition Loopback indicator 1 DS1 Line 1 2 DS1 Line 2 3 DS1 Line 3 4 DS1 Line 4 5 DS1 Line 5 … |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.29 | Columndsx3SubRateEnable | read-write | current | This variable controls whether the DS3 subrates are enabled or not. The DS3 subrate is part of DSU functionality. This object is currently supported only in FR… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.30 | Columndsx3DsuSelect | read-write | current | The dsx3DsuSelect variable controls the type of DSU mode to be selected. The 'dsx3SubRateEnable' has to be set to 'enable' before selecting the mode in 'dsx3Ds… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.31 | Columndsx3LineRate | read-write | current | The desired line rate when 'dsx3SubRateEnable' is enabled. If dsx3DsuSelect is set to 'dl3100Mode', the line rate can be configured in steps of 300 Kbps. If ds… |
| 1.3.6.1.4.1.351.110.4.4.1.1.1.1.32 | Columndsx3LineScrambleEnable | read-write | current | This variable turns the scrambling feature ON/OFF The scrambling is a technique that enables framing to be maintained on certain medium-speed edge and trunk in… |
| 1.3.6.1.4.1.351.110.4.4.1.1.2 | Scalardsx3LineNumOfValidEntries | read-only | current | The number of DSX3 configuration entries (regardless of their current configuration) in the cwDsx3ConfigTable. |
| 1.3.6.1.4.1.351.110.4.4.1.2 | Nodedsx3AlarmConfig | |||
| 1.3.6.1.4.1.351.110.4.4.1.2.1 | Tabledsx3AlarmConfigTable | not-accessible | current | The DSX3 interface alarm configuration table. This table contains the parameters associated with detecting and declaring alarms for the interface. The paramete… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1 | Rowdsx3AlarmConfigEntry | not-accessible | current | An entry in the DSX3 Alarm Configuration table. Thresholds may be configured for: Line Code Violations (LCV), LineErrored Seconds (LES), Line Severely Errored … |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.1 | Columndsx3RedSeverity | read-write | current | This variable is used to setup the severity of RED alarm. So when LOS/LOF alarm is detected the card will send the alarm with appropriate severity status. A ma… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.2 | Columndsx3RAISeverity | read-write | current | This variable is used to setup the severity of RAI alarm. So when RAI alarm is detected the card will send the alarm with appropriate severity status. A major … |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.3 | Columndsx3NEAlarmUpCount | read-write | current | This parameter specifies the increment to the Near End alarm integration counters. The local alarms are LOS and LOF. The Default value is 6 and the integration… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.4 | Columndsx3NEAlarmDownCount | read-write | current | This parameter specifies the decrement to the Near End alarm integration counters. The local alarms are LOS and LOF. The Default value is 1 and the integration… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.5 | Columndsx3NEAlarmThreshold | read-write | current | The value set in this object determines the value that the alarm integration counter must reach for an near end Alarm to be declared. If the up count is 6, the… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.6 | Columndsx3FEAlarmUpCount | read-write | current | This parameter specifies the increment to the Far End alarm integration counters. The local alarms are RAI and AIS. The Default value is 6 and the integration … |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.7 | Columndsx3FEAlarmDownCount | read-write | current | This parameter specifies the decrement to the Far End alarm integration counters. The local alarms are AIS and RAI. The Default value is 1. The integration cou… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.8 | Columndsx3FEAlarmThreshold | read-write | current | The value set in this object determines the value that the alarm integration counter must reach for an far end Alarm to be declared. If the up count is 6, the … |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.9 | Columndsx3StatisticalAlarmSeverity | read-write | current | This variable is used to setup the severity of any of the Statistical alarms. So when a Statistical Counter exceeds its specified threshold the card will send … |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.10 | Columndsx3LCV15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.11 | Columndsx3LCV24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.12 | Columndsx3LES15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.13 | Columndsx3LES24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.14 | Columndsx3LSES15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.15 | Columndsx3LSES24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.16 | Columndsx3PCV15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not suppo… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.17 | Columndsx3PCV24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.18 | Columndsx3PES15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not suppo… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.19 | Columndsx3PES24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.20 | Columndsx3PSES15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object does not app… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.21 | Columndsx3PSES24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.22 | Columndsx3SEFS15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not suppo… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.23 | Columndsx3SEFS24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.24 | Columndsx3AISS15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not suppo… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.25 | Columndsx3AISS24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.26 | Columndsx3UAS15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.27 | Columndsx3UAS24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.28 | Columndsx3E3BIP8CV15MinThreshold | read-write | current | G.832 BIP-8 error monitoring byte. 15 minute threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS This object is not su… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.29 | Columndsx3E3BIP8CV24HrThreshold | read-write | current | G.832 BIP-8 error monitoring byte. 24 hour threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS. This object is not sup… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.30 | Columndsx3E3BIP8ES15MinThreshold | read-write | current | G.832 BIP-8 error monitoring byte. 15 minute threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS. This object is not s… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.31 | Columndsx3E3BIP8ES24HrThreshold | read-write | current | G.832 BIP-8 error monitoring byte. 24 hour threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS This object is not supp… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.32 | Columndsx3E3BIP8SES15MinThreshold | read-write | current | G.832 BIP-8 error monitoring byte. 15 minute threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS This object is not su… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.33 | Columndsx3E3BIP8SES24HrThreshold | read-write | current | G.832 BIP-8 error monitoring byte. 24 hour threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS This object is not supp… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.34 | Columndsx3CCV15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not appli… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.35 | Columndsx3CCV24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.36 | Columndsx3CES15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not appli… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.37 | Columndsx3CES24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. This object is not… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.38 | Columndsx3CSES15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not appli… |
| 1.3.6.1.4.1.351.110.4.4.1.2.1.1.39 | Columndsx3CSES24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. This object is not… |
| 1.3.6.1.4.1.351.110.4.4.1.3 | Nodedsx3Alarm | |||
| 1.3.6.1.4.1.351.110.4.4.1.3.1 | Tabledsx3AlarmTable | not-accessible | current | The DSX3 interface alarm table. This table contains the performance statistics and Error Events based on 15 minute and/or 24 hour interval. Performance Paramet… |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1 | Rowdsx3AlarmEntry | not-accessible | current | An entry in the DSX3 Alarm table. The bucket statistics(15 minute and 24 hour interval statistics) are gathered for each ds3/e3 interface. Any entry is created… |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.1 | Columndsx3LineAlarmState | read-only | current | This variable is a bitmap of the DSX3 Line ALarms on the card. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alarm 0… |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.2 | Columndsx3LineStatisticalAlarmState | read-only | current | This is a bitmap of the DSX3 Line Statistical Alarms on the card. Zero indicates no alarms. Itemized below are the individual alarm bits: BitPosition Alarm 0 L… |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.3 | Columndsx3LCVCurrent | read-only | current | The number of Line Code Violations(LCV) encountered by the interface in current 15 minute period. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.4 | Columndsx3LCV15MinBucket | read-only | current | The number of Line Code Violations(LCV) encountered by the interface in current last 15 minute period. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.5 | Columndsx3LCV24HrBucket | read-only | current | The number of Line Code Violations(LCV) encountered by the interface in current last 24 hour period. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.6 | Columndsx3LESCurrent | read-only | current | The number of Line Errored Seconds(LES) encountered by the interface in current 15 minute period. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.7 | Columndsx3LES15MinBucket | read-only | current | The number of Line Errored Seconds(LES) encountered by the interface in last 15 minute period. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.8 | Columndsx3LES24HrBucket | read-only | current | The number of Line Errored Seconds(LES) encountered by the interface in last 24 hour period. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.9 | Columndsx3LSESCurrent | read-only | current | The number of Line Severely Errored Seconds(LSES) encountered by the interface in current 15 minute period. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.10 | Columndsx3LSES15MinBucket | read-only | current | The number of Line Severely Errored Seconds(LSES) encountered by the interface in last 15 minute period. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.11 | Columndsx3LSES24HrBucket | read-only | current | The number of Line Severely Errored Seconds(LSES) encountered by the interface in last 24 hour period. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.12 | Columndsx3PCVCurrent | read-only | current | The number of P-bit Coding Violations(PCV) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.13 | Columndsx3PCV15MinBucket | read-only | current | The number of P-bit Coding Violations(PCV) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.14 | Columndsx3PCV24HrBucket | read-only | current | The number of P-bit Coding Violations(PCV) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.15 | Columndsx3PESCurrent | read-only | current | The number of P-bit Errored Seconds(PES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.16 | Columndsx3PES15MinBucket | read-only | current | The number of P-bit Errored Seconds(PES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.17 | Columndsx3PES24HrBucket | read-only | current | The number of P-bit Errored Seconds(PES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.18 | Columndsx3PSESCurrent | read-only | current | The number of P-bit Severely Errored Seconds(PSES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.19 | Columndsx3PSES15MinBucket | read-only | current | The number of P-bit Severely Errored Seconds(PSES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.20 | Columndsx3PSES24HrBucket | read-only | current | The number of P-bit Severely Errored Seconds(PSES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.21 | Columndsx3SEFSCurrent | read-only | current | The number of Severely Errored Framing Seconds(PSES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.22 | Columndsx3SEFS15MinBucket | read-only | current | The number of Severely Errored Framing Seconds(PSES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.23 | Columndsx3SEFS24HrBucket | read-only | current | The number of Severely Errored Framing Seconds(PSES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.24 | Columndsx3AISSCurrent | read-only | current | The number of AIS Severely Errored Seconds encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.25 | Columndsx3AISS15MinBucket | read-only | current | The number of AIS Severely Errored Seconds encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.26 | Columndsx3AISS24HrBucket | read-only | current | The number of AIS Severely Errored Seconds encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.27 | Columndsx3UASCurrent | read-only | current | The number of Unavailable Seconds(UAS) encountered by the interface in current 15 minute period. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.28 | Columndsx3UAS15MinBucket | read-only | current | The number of Unavailable Seconds(UAS) encountered by the interface in last 15 minute period. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.29 | Columndsx3UAS24HrBucket | read-only | current | The number of Unavailable Seconds(UAS) encountered by the interface in last 24 Hour period. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.30 | Columndsx3PercentLcvEFS | read-only | current | This object gives the percentage of seconds without any LCV Errors in the total elapsed seconds. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.31 | Columndsx3E3BIP8CVCurrent | read-only | current | The number of G.832 BIP-8 Coding Violations (CV) encountered by the interface in current 15 minute period. This object is not supported in FRSM-VHS and CESM-T3… |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.32 | Columndsx3E3BIP8CV15MinBucket | read-only | current | The number of G.832 BIP-8 Coding Violations (CV) encountered by the interface in last 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.33 | Columndsx3E3BIP8CV24HrBucket | read-only | current | The number of G.832 BIP-8 Coding Violations (CV) encountered by the interface in last 24 Hour period. This object is not supported in FRSM-VHS and CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.34 | Columndsx3E3BIP8ESCurrent | read-only | current | The number of G.832 BIP-8 Errored Seconds(ES) encountered by the interface in current 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.35 | Columndsx3E3BIP8ES15MinBucket | read-only | current | The number of G.832 BIP-8 Errored Seconds(ES) encountered by the interface in last 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.36 | Columndsx3E3BIP8ES24HrBucket | read-only | current | The number of G.832 BIP-8 Errored Seconds(ES) encountered by the interface in last 24 Hour period. This object is not supported in FRSM-VHS and CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.37 | Columndsx3E3BIP8SESCurrent | read-only | current | The number of G.832 BIP-8 Severely Errored Seconds(SES) encountered by the interface in current 15 minute period. This object is not supported in FRSM-VHS and … |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.38 | Columndsx3E3BIP8SES15MinBucket | read-only | current | The number of G.832 BIP-8 Severely Errored Seconds(SES) encountered by the interface in last 15 minute period. This object is not supported in FRSM-VHS and CES… |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.39 | Columndsx3E3BIP8SES24HrBucket | read-only | current | The number of G.832 BIP-8 Severely Errored Seconds(SES) encountered by the interface in last 24 Hour period. This object is not supported in FRSM-VHS and CESM-… |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.40 | Columndsx3LineAlarmClrButton | read-write | current | Setting this object to dsx3LineAlarmClear will cause all the alarms statuses and counters to reset. |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.41 | Columndsx3CCVCurrent | read-only | current | The number of C-bit Coding Violations(CCV) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.42 | Columndsx3CCV15MinBucket | read-only | current | The number of C-bit Coding Violations(CCV) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.43 | Columndsx3CCV24HrBucket | read-only | current | The number of C-bit Coding Violations(CCV) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.44 | Columndsx3CESCurrent | read-only | current | The number of C-bit Errored Seconds(CES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.45 | Columndsx3CES15MinBucket | read-only | current | The number of C-bit Errored Seconds(CES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.46 | Columndsx3CES24HrBucket | read-only | current | The number of C-bit Errored Seconds(CES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.47 | Columndsx3CSESCurrent | read-only | current | The number of C-bit Severely Errored Seconds(CSES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.48 | Columndsx3CSES15MinBucket | read-only | current | The number of C-bit Severely Errored Seconds(CSES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.3.1.1.49 | Columndsx3CSES24HrBucket | read-only | current | The number of C-bit Severely Errored Seconds(CSES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.4 | Nodedsx3Counter | |||
| 1.3.6.1.4.1.351.110.4.4.1.4.1 | Tabledsx3CounterTable | not-accessible | current | This table is for ds3/e3 statistics. This table maintains the number of times the line encountered LOS, LOF, AIS, RAI, CCV and Framing Errors(FE) from the time… |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1 | Rowdsx3CounterEntry | not-accessible | current | An entry in the table. Statistics are gathered for each ds3/e3 interface. An entry is created automatically for each ds3/e3 interface that is activated. |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1.1 | Columndsx3RcvLOSCount | read-only | current | The number of times the Loss of Signal was detected with or without integrating to LOS alarm. |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1.2 | Columndsx3RcvOOFCount | read-only | current | The number of times the Out of Frame was detected with or without integrating to OOF alarm. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1.3 | Columndsx3RAICount | read-only | current | The number of times Yellow Alarms was detected with or without integrating to RAI alarm. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1.4 | Columndsx3CCVCount | read-only | current | The counter associated with the number of C Bit Coding Violations encountered by a DS3/E3 interface. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1.5 | Columndsx3FECount | read-only | current | The number of Framing Pattern Errors encountered by a DS3/E3 interface. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1.6 | Columndsx3AtmHECCount | read-only | current | The number of Header Check Sequence(HCS) Errors. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1.7 | Columndsx3AtmHECSecCount | read-only | current | The number of HEC errored seconds. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1.8 | Columndsx3AtmSEHECSecCount | read-only | current | The number of Severely HEC error seconds. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1.9 | Columndsx3CounterClrButton | read-write | current | This variable is used to clear all the counters. |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1.10 | Columndsx3RcvPERRCounter | read-only | current | The number of P-bit parity error. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1.11 | Columndsx3RcvFEBECounter | read-only | current | The number of Far-end block error. This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1.12 | Columndsx3RcvEXZCounter | read-only | current | The number of excessive zeros This object is not supported in CESM-T3/E3 |
| 1.3.6.1.4.1.351.110.4.4.1.4.1.1.13 | Columndsx3LCVCount | read-only | current | The counter associated with the number of Line Coding Violations encountered by a DS3/E3 interface. |
| 1.3.6.1.4.1.351.110.4.4.2.1 | Nodedsx3PlcpConfig | |||
| 1.3.6.1.4.1.351.110.4.4.2.1.1 | Tabledsx3PlcpConfigTable | not-accessible | current | This table contains ATM interface DS3 PLCP configuration parameters. |
| 1.3.6.1.4.1.351.110.4.4.2.1.1.1 | Rowdsx3PlcpConfigEntry | not-accessible | current | An entry in the DSX3 PLCP Configuration table. |
| 1.3.6.1.4.1.351.110.4.4.2.1.1.1.1 | Columndsx3PlcpNum | read-only | current | This object identifies the dsx3 PLCP interface. The value of this object must be same as the value specified in 'dsx3LineNum' object from cwDsx3ConfigTable. |
| 1.3.6.1.4.1.351.110.4.4.2.1.1.1.2 | Columndsx3PlcpCellFraming | read-only | current | The value for this object sets the cell delineation method used by the interface. The cell delineation defines how a receiving device recognizes the start and … |
| 1.3.6.1.4.1.351.110.4.4.2.1.1.1.3 | Columndsx3PlcpPayloadScramble | read-write | current | The value for this object is used for enabling/disabling PLCP cell scrambling. |
| 1.3.6.1.4.1.351.110.4.4.2.1.1.1.4 | Columndsx3PlcpLoopCommand | read-write | current | specifies the type of loopback on the line. The possible value(s) are : noLoop (1): Not in loopback. remoteLineLoop (2): Remote Line Loopback. localLineLoop (3… |
| 1.3.6.1.4.1.351.110.4.4.2.1.2 | Scalardsx3PlcpNumOfValidEntries | read-only | current | This variable indicates the maximum number of entries in cwDsx3ConfigTable. |
| 1.3.6.1.4.1.351.110.4.4.2.2 | Nodedsx3PlcpAlarmConfig | |||
| 1.3.6.1.4.1.351.110.4.4.2.2.1 | Tabledsx3PlcpAlarmConfigTable | not-accessible | current | This table contains the ATM interface PLCP alarm parameters. |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1 | Rowdsx3PlcpAlarmConfigEntry | not-accessible | current | An entry in the DSX3 PLCP Alarm Configuration table. Thresholds may be configured for: Errored Seconds (ES) Coding Violations (CV) Severely Errored Seconds (SE… |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.1 | Columndsx3PlcpRedSeverity | read-write | current | This variable is used to setup the severity of PLCP RED alarm. So when PLCP_OOF alarm is detected the card will declare the alarm with appropriate severity sta… |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.2 | Columndsx3PlcpRAISeverity | read-write | current | This variable is used to setup the severity of PLCP RAI alarm. So when PLCP RAI alarm is detected the card will send the alarm with appropriate severity status… |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.3 | Columndsx3PlcpLssSeverity | read-write | current | This variable is used to setup the severity of PLCP RAI alarm. So when PLCP LSS alarm is detected the card will send the alarm with appropriate severity status… |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.4 | Columndsx3PlcpLssEnable | read-write | current | This objects specifies whether the LSS feature is enabled/disabled. |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.5 | Columndsx3PlcpLssCodeConnected | read-write | current | This object derfines the value of the LSS code that is to be interpreted as Link Connected. |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.6 | Columndsx3PlcpLssCodeRxLinkDn | read-write | current | This object defines the value of the LSS code that is to be identified as Receive Link Down. |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.7 | Columndsx3PlcpLssCodeRxLinkUp | read-write | current | This object defines the value of the LSS code that is to be interpreted as Receive Link Up. |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.8 | Columndsx3PlcpStatisticalAlarmSeverity | read-write | current | This variable sets up the severity of PLCP Statistical alarm. So when PLCP Statistical alarm is detected, the card will send the alarm with appropriate severit… |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.9 | Columndsx3PlcpBip8CV15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.10 | Columndsx3PlcpBip8CV24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.11 | Columndsx3PlcpBip8ES15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.12 | Columndsx3PlcpBip8ES24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.13 | Columndsx3PlcpBip8SES15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.14 | Columndsx3PlcpBip8SES24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.15 | Columndsx3PlcpSEFS15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.16 | Columndsx3PlcpSEFS24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.17 | Columndsx3PlcpUAS15MinThreshold | read-write | current | The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. |
| 1.3.6.1.4.1.351.110.4.4.2.2.1.1.18 | Columndsx3PlcpUAS24HrThreshold | read-write | current | The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is c… |
| 1.3.6.1.4.1.351.110.4.4.2.3 | Nodedsx3PlcpAlarm | |||
| 1.3.6.1.4.1.351.110.4.4.2.3.1 | Tabledsx3PlcpAlarmTable | not-accessible | current | This table contains ATM interface DS3 PLCP alarm configuration. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1 | Rowdsx3PlcpAlarmEntry | not-accessible | current | An entry in the ATM DS3 PLCP alarm table. Bucket statistics (15 minute and 24 Hour interval) are gathered for each ds3/e3 interface automatically. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.1 | Columndsx3PlcpLineAlarmState | read-only | current | This variable is a bitmap of the DSX3 Line alarms. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alarm 0 Receiving R… |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.2 | Columndsx3PlcpLineStatisticalAlarmState | read-only | current | This variable is a bitmap of the DSX3 Line Statictical Alarms on the card. A value of zero indicates no alarms. Itemized below are the individual alarm bits: B… |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.3 | Columndsx3PlcpBip8CVCurrent | read-only | current | This counter counts the number of BIP-8 code violations encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.4 | Columndsx3PlcpBip8CV15MinBucket | read-only | current | The counter associated with the number of BIP-8 code violations in the last 15 minute period encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.5 | Columndsx3PlcpBip8CV24HrBucket | read-only | current | The counter associated with the number of BIP-8 code violations in the last 24 hour period encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.6 | Columndsx3PlcpBip8ESCurrent | read-only | current | This counter counts the number of BIP-8 code violations Errored Seconds encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.7 | Columndsx3PlcpBip8ES15MinBucket | read-only | current | This counter counts the number of BIP-8 code violations Errored Seconds in the last 15 minutes encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.8 | Columndsx3PlcpBip8ES24HrBucket | read-only | current | This counter counts the number of BIP-8 code violations Errored Seconds in the last 24 hours encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.9 | Columndsx3PlcpBip8SESCurrent | read-only | current | This counter counts the number of Bip8 code violations Severely Errored Seconds encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.10 | Columndsx3PlcpBip8SES15MinBucket | read-only | current | This counter counts the number of BIP-8 Severely Errored Seconds in the last 15 minutes encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.11 | Columndsx3PlcpBip8SES24HrBucket | read-only | current | This counter counts the number of BIP-8 Severely Errored Seconds in the last 24 hours encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.12 | Columndsx3PlcpSEFSCurrent | read-only | current | This counter counts the number of Severely Errored Framing Seconds encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.13 | Columndsx3PlcpSEFS15MinBucket | read-only | current | This counter counts the number of Severely Errored Framing Seconds in the last 15 minutes encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.14 | Columndsx3PlcpSEFS24HrBucket | read-only | current | This counter counts the number of Severely Errored Framing Seconds in the last 24 hours encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.15 | Columndsx3PlcpUASCurrent | read-only | current | This counter counts the number of Unavailable Seconds encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.16 | Columndsx3PlcpUAS15MinBucket | read-only | current | This counter counts the number of Unavailable Seconds in the last 15 minutes encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.17 | Columndsx3PlcpUAS24HrBucket | read-only | current | This counter counts the number of Unavailable Seconds in the last 24 hours encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.3.1.1.18 | Columndsx3PlcpAlarmClrButton | read-write | current | This variable is used to clear all the alarms. |
| 1.3.6.1.4.1.351.110.4.4.2.4 | Nodedsx3PlcpCounter | |||
| 1.3.6.1.4.1.351.110.4.4.2.4.1 | Tabledsx3PlcpCounterTable | not-accessible | current | The table for DS3 PLCP counter table. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1 | Rowdsx3PlcpCounterEntry | not-accessible | current | An entry in the DS3 PLCP counter table. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1.1 | Columndsx3PlcpRcvBip8Count | read-only | current | The number of BIP-8 errors encountered by the interface. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1.2 | Columndsx3PlcpRcvOOFCount | read-only | current | The number of times the Out of Frame(OOF) was detected with or without integrating to OOF alarm. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1.3 | Columndsx3PlcpRcvRAICount | read-only | current | The number of times Remote Alarm Indication(RAI) was detected with or without integrating to RAI alarm. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1.4 | Columndsx3PlcpFECount | read-only | current | The number of Framing Errors detected. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1.5 | Columndsx3PlcpFESecCount | read-only | current | The number of Framing Error errored seconds. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1.6 | Columndsx3PlcpSEFESecCount | read-only | current | The number of Severely errored Framing error seconds. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1.7 | Columndsx3PlcpFEBECount | read-only | current | The number of Far End Block Errors(FEBE) detected. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1.8 | Columndsx3PlcpFEBESecCount | read-only | current | The number of FEBE errored seconds. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1.9 | Columndsx3PlcpSEFEBESecCount | read-only | current | The number of Severely errored FEBE seconds. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1.10 | Columndsx3PlcpHECCount | read-only | current | The number of HCS Errors. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1.11 | Columndsx3PlcpHECSecCount | read-only | current | The number of HEC errored seconds. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1.12 | Columndsx3PlcpSEHECSecCount | read-only | current | The number of Severely HEC error seconds. |
| 1.3.6.1.4.1.351.110.4.4.2.4.1.1.13 | Columndsx3PlcpCounterClrButton | read-write | current | This variable is used to clear all the counters. |
| 1.3.6.1.4.1.351.110.4.4.2.4.2 | Scalardsx3PlcpCounterValidEntries | read-only | current | The maximum number of entries in the dsx3PlcpCounterTable. |
| 1.3.6.1.4.1.351.150.59 | IdentityciscoMgx82xxDsx3MIB | The MIB Module for DS3/E3 interface configuration , statistics and Alarm configuration. This MIB is supported in T3/E3 service modules in MGX products. Some of… | ||
| 1.3.6.1.4.1.351.150.59.2 | NodecmDsx3MIBConformance | |||
| 1.3.6.1.4.1.351.150.59.2.1 | NodecmDsx3MIBGroups | |||
| 1.3.6.1.4.1.351.150.59.2.1.1 | GroupcmDsx3GeneralGroup | current | The collection of objects which are used for providing number of entries in dsx3 and PLCP tables. | |
| 1.3.6.1.4.1.351.150.59.2.1.2 | GroupcmDsx3ConfGroup | current | The collection of objects which are used for configuring DS3/E3 interfaces. | |
| 1.3.6.1.4.1.351.150.59.2.1.3 | GroupcmDsx3E3ConfGroup | current | The collection of objects which are applicable for E3 interfaces only. | |
| 1.3.6.1.4.1.351.150.59.2.1.4 | GroupcmDsx3BertConfigGroup | current | The collection of objects which are used for BERT on DS3/E3 interfaces. | |
| 1.3.6.1.4.1.351.150.59.2.1.5 | GroupcmDsx3StatsGroup | current | The collection of objects related to DS3/E3 statistics. | |
| 1.3.6.1.4.1.351.150.59.2.1.6 | GroupcmDsx3E3AlarmConfGenGroup | current | The collection of objects used for alarm configuration of DS3 and E3 interfaces. | |
| 1.3.6.1.4.1.351.150.59.2.1.7 | GroupcmDsx3AlarmConfGroup | current | The collection of objects used for alarm configuration of DS3 interfaces. | |
| 1.3.6.1.4.1.351.150.59.2.1.8 | GroupcmDsx3E3AlarmConfGroup | current | The collection of objects used for alarm configuration of E3 interfaces. | |
| 1.3.6.1.4.1.351.150.59.2.1.9 | GroupcmDsx3AlarmStatsGenGroup | current | The collection of objects related to performance statistics and error events for ds3 end e3 interfaces. | |
| 1.3.6.1.4.1.351.150.59.2.1.10 | GroupcmDsx3AlarmStatsGroup | current | The collection of objects related to performance statistics and error events for ds3 interfaces. | |
| 1.3.6.1.4.1.351.150.59.2.1.11 | GroupcmDsx3E3AlarmStatsGroup | current | The collection of objects related to performance statistics and error events for e3 interfaces. | |
| 1.3.6.1.4.1.351.150.59.2.1.12 | GroupcmDsx3PlcpConfGroup | current | The collection of objects related to PLCP Configuration on DS3 interfaces. | |
| 1.3.6.1.4.1.351.150.59.2.1.13 | GroupcmDsx3PlcpStatsGroup | current | The collection of objects related to PLCP statistics on DS3 interfaces. | |
| 1.3.6.1.4.1.351.150.59.2.1.14 | GroupcmDsx3PlcpAlarmConfGroup | current | The collection of objects used for PLCP Alarm configuration on DS3 interfaces. | |
| 1.3.6.1.4.1.351.150.59.2.1.15 | GroupcmDsx3PlcpAlarmGroup | current | The collection of objects used for PLCP Alarm configuration on DS3 interfaces. | |
| 1.3.6.1.4.1.351.150.59.2.2 | NodecmDsx3MIBCompliances | |||
| 1.3.6.1.4.1.351.150.59.2.2.1 | CompliancecmDsx3Compliance | current | The compliance statement for objects related to DS3 MIB. |