CISCO-NETSYNC-MIB
111 objects
The Synchronous Ethernet (SyncE) MIB is defined for monitoring network synchronization based on ITU-T G.781 clock selection. Synchronous Ethernet (SyncE) is a standard defined for delivering timing to the remote NEs through a Packet Network. SyncE is well defined by ITU-T which included G.8261, G.8262, G.8264 and G.781. It leverages the PHY layer of Ethernet to transmit frequency to the remote sites. Its functionality and accuracy mimics that of the SONET/SDH network because of its physical layer characteristic. In order to allow best clock source traceabiliy, correctly define the timing source and helps preventing timing loop, Synchronization Status Message is required for SyncE. This is similar to SONET/SDH. However, since SONET/SDH use 4 bits from the two S bytes in the SONET/SDH overhead frame for such message, Ethernet relies on a different channel called ESMC (Ethernet Synchronization Messaging Channel) which is based on IEEE 802.3 Organization Specific Slow Protocol. Glossary: AIS: Alarm Indication Signal ATM: Asynchronous Transfer Mode EEC: Ethernet Equipment Clock ESMC: Ethernet Synchronization Messaging Channel QL: Quality Level SASE: Stand Alone Synchronization Equipment SSM: Synchronization Status Messaging
Imported Objects
| CISCO-SMI | ciscoMgmt |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Gauge32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.761 | IdentityciscoNetsyncMIB | The Synchronous Ethernet (SyncE) MIB is defined for monitoring network synchronization based on ITU-T G.781 clock selection. Synchronous Ethernet (SyncE) is a … | ||
| 1.3.6.1.4.1.9.9.761.0 | NodeciscoNetsyncMIBNotifs | |||
| 1.3.6.1.4.1.9.9.761.0.1 | NotificationciscoNetsyncSelectedT0Clock | current | T0 clock selection notification. This notification is generated when one of the following conditions is met: - A new clock source is selected by the T0 clock s… | |
| 1.3.6.1.4.1.9.9.761.0.2 | NotificationciscoNetsyncSelectedT4Clock | current | T4 clock selection notification. This notification is generated when one of the following conditions is met: - A new clock source is selected by the T4 clock s… | |
| 1.3.6.1.4.1.9.9.761.0.3 | NotificationciscoNetsyncInputSignalFailureStatus | current | Input clock source signal failure notification. This notification is generated when a signal failure event is reported on an input clock source. One of the con… | |
| 1.3.6.1.4.1.9.9.761.0.4 | NotificationciscoNetsyncInputAlarmStatus | current | Input clock source alarm notification. This notification is generated when an alarm event is reported on an input clock source. | |
| 1.3.6.1.4.1.9.9.761.1 | NodeciscoNetsyncMIBObjects | |||
| 1.3.6.1.4.1.9.9.761.1.1 | NodeciscoNetsyncMIBTables | |||
| 1.3.6.1.4.1.9.9.761.1.1.1 | TablecnsClkSelGlobalTable | not-accessible | current | G.781 clock selection process table. This table contains the global parameters for the G.781 clock selection process. |
| 1.3.6.1.4.1.9.9.761.1.1.1.1 | RowcnsClkSelGlobalEntry | not-accessible | current | An entry is added to cnsClkSelGlobalTable when G.781 clock selection is enabled in the device configuration. The entry is removed when G.781 clock selection is… |
| 1.3.6.1.4.1.9.9.761.1.1.1.1.1 | ColumncnsClkSelGloProcIndex | not-accessible | current | An index that uniquely represents a clock selection process. This index is assigned arbitrarily by the system and may not be persistent across reboots. |
| 1.3.6.1.4.1.9.9.761.1.1.1.1.2 | ColumncnsClkSelGlobProcessMode | read-only | current | This object indicates the QL mode of the network synchronization clock selection process as described in ITU-T standard G.781 section 5.12. |
| 1.3.6.1.4.1.9.9.761.1.1.1.1.3 | ColumncnsClkSelGlobClockMode | read-only | current | This object indicates the operating mode of the system clock. |
| 1.3.6.1.4.1.9.9.761.1.1.1.1.4 | ColumncnsClkSelGlobNetsyncEnable | read-only | current | This object indicates whether the G.781 clock selection is enabled or not. 'true' - G.781 clock selection is enabled 'false' - G.781 clock selection is disabled |
| 1.3.6.1.4.1.9.9.761.1.1.1.1.5 | ColumncnsClkSelGlobRevertiveMode | read-only | current | This object indicates the revertive mode setting in the G.781 clock selection process. The switching of clock sources can be made revertive or non-revertive. I… |
| 1.3.6.1.4.1.9.9.761.1.1.1.1.6 | ColumncnsClkSelGlobESMCMode | read-only | current | This object indicates if global ESMC is enabled. With ESMC enabled globally, the system is capable of handling ESMC messages. |
| 1.3.6.1.4.1.9.9.761.1.1.1.1.7 | ColumncnsClkSelGlobEECOption | read-only | current | This object indicates the network synchronization EEC (Ethernet Equipment Clock) option. |
| 1.3.6.1.4.1.9.9.761.1.1.1.1.8 | ColumncnsClkSelGlobNetworkOption | read-only | current | This object indicates the synchronization network option. |
| 1.3.6.1.4.1.9.9.761.1.1.1.1.9 | ColumncnsClkSelGlobHoldoffTime | read-only | current | This object indicates the global holdoff time in the G.781 clock selection process. |
| 1.3.6.1.4.1.9.9.761.1.1.1.1.10 | ColumncnsClkSelGlobWtrTime | read-only | current | This object indicates the global wait-to-restore time in the G.781 clock selection process. |
| 1.3.6.1.4.1.9.9.761.1.1.1.1.11 | ColumncnsClkSelGlobNofSources | read-only | current | This object indicates the number of synchronization sources currently configured for the G.781 clock selection process. |
| 1.3.6.1.4.1.9.9.761.1.1.1.1.12 | ColumncnsClkSelGlobLastHoldoverSeconds | read-only | current | This object indicates the duration of the last holdover period in seconds. If the holdover duration is less than a second, the object will carry the value zero. |
| 1.3.6.1.4.1.9.9.761.1.1.1.1.13 | ColumncnsClkSelGlobCurrHoldoverSeconds | read-only | current | This object indicates the duration of the current holdover period. If a system clock is in holdover mode, the object carries the current holdover duration in s… |
| 1.3.6.1.4.1.9.9.761.1.1.2 | TablecnsSelectedInputSourceTable | not-accessible | current | T0 selected clock source table. This table contains the selected clock source for the input T0 clock. |
| 1.3.6.1.4.1.9.9.761.1.1.2.1 | RowcnsSelectedInputSourceEntry | not-accessible | current | An entry is created in the table when the G.781 clock selection process has successfully selected a T0 clock source. The entry shall remain during the time the… |
| 1.3.6.1.4.1.9.9.761.1.1.2.1.1 | ColumncnsSelInpSrcNetsyncIndex | not-accessible | current | An index that uniquely represents an entry in this table. This index is assigned arbitrarily by the clock selection process and may not be persistent across re… |
| 1.3.6.1.4.1.9.9.761.1.1.2.1.2 | ColumncnsSelInpSrcName | read-only | current | This object indicates the name of the selected T0 clock. |
| 1.3.6.1.4.1.9.9.761.1.1.2.1.3 | ColumncnsSelInpSrcIntfType | read-only | current | This object indicates the type of the selected T0 clock. |
| 1.3.6.1.4.1.9.9.761.1.1.2.1.4 | ColumncnsSelInpSrcQualityLevel | read-only | current | This object indicates the selected T0 clock source's effective quality level, which is the derived clock quality based on the three factors: (a) Received quali… |
| 1.3.6.1.4.1.9.9.761.1.1.2.1.5 | ColumncnsSelInpSrcPriority | read-only | current | This object indicates the configured priority of the selected T0 clock. A smaller value represents a higher priority. |
| 1.3.6.1.4.1.9.9.761.1.1.2.1.6 | ColumncnsSelInpSrcTimestamp | read-only | current | This object indicates the timestamp of the T0 clock source being selected by the G.781 clock selection process. |
| 1.3.6.1.4.1.9.9.761.1.1.2.1.7 | ColumncnsSelInpSrcFSW | read-only | current | This object indicates the forced switching flag. Forced switching, as described in G.781, is used to override the currently selected synchronization source. Th… |
| 1.3.6.1.4.1.9.9.761.1.1.2.1.8 | ColumncnsSelInpSrcMSW | read-only | current | This object indicates the manual switching flag. The 'true' value indicates the currently selected clock source is a result of the manual switch command. The c… |
| 1.3.6.1.4.1.9.9.761.1.1.3 | TablecnsInputSourceTable | not-accessible | current | T0 clock source table. This table contains a list of input sources for input T0 clock selection. |
| 1.3.6.1.4.1.9.9.761.1.1.3.1 | RowcnsInputSourceEntry | not-accessible | current | An entry is created in the table when a user adds a T0 clock source in the configuration. An entry is removed in the table when a user removes a T0 clock sourc… |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.1 | ColumncnsInpSrcNetsyncIndex | not-accessible | current | An index that uniquely represents an entry in this table. This index is assigned arbitrarily by the clock selection process and may not be persistent across re… |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.2 | ColumncnsInpSrcName | read-only | current | This object indicates the name of an input clock source configured for the T0 clock selection. |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.3 | ColumncnsInpSrcIntfType | read-only | current | This object indicates the type of an input clock source configured for the T0 clock selection. |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.4 | ColumncnsInpSrcPriority | read-only | current | This object indicates the priority of an input clock source configured for the T0 clock selection. A smaller value represents a higher priority. |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.5 | ColumncnsInpSrcESMCCap | read-only | current | This object indicates the ESMC capability of an input clock source configured for the T0 clock selection. This is applicable only to Synchronous Ethernet input… |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.6 | ColumncnsInpSrcSSMCap | read-only | current | This object indicates the SSM capability of an input clock source configured for the T0 clock selection. This is applicable only to any synchronous interface c… |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.7 | ColumncnsInpSrcQualityLevelTxCfg | read-only | current | This object indicates the configured transmit clock quality level of an input clock source. |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.8 | ColumncnsInpSrcQualityLevelRxCfg | read-only | current | This object indicates the configured receive clock quality level of an input clock source. |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.9 | ColumncnsInpSrcQualityLevelTx | read-only | current | This object indicates the most recent clock quality level transmitted on the input clock source. |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.10 | ColumncnsInpSrcQualityLevelRx | read-only | current | This object indicates the last clock quality level received on the input clock source. |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.11 | ColumncnsInpSrcQualityLevel | read-only | current | This object indicates the current clock quality level of the input clock source. This is the effective quality which is derived from three values: 1) most rece… |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.12 | ColumncnsInpSrcHoldoffTime | read-only | current | This object indicates the hold-off time value of an input clock source. The hold-off time prevents short activation of signal failure is passed to the selectio… |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.13 | ColumncnsInpSrcWtrTime | read-only | current | This object indicates the wait-to-restore time value of an input clock source. The wait-to-restore time ensures that a previous failed synchronization source i… |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.14 | ColumncnsInpSrcLockout | read-only | current | This object indicates whether or not the lockout command has been applied to a clock source. The 'true' value means the clock source is not considered by the s… |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.15 | ColumncnsInpSrcSignalFailure | read-only | current | This object indicates whether or not a signal failure event is currently being reported on the input clock source. |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.16 | ColumncnsInpSrcAlarm | read-only | current | This object indicates whether or not an alarm event is currently being reported on the input clock source. |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.17 | ColumncnsInpSrcAlarmInfo | read-only | current | This object indicates the alarm reasons of an input clock source if an alarm event is being reported on it. |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.18 | ColumncnsInpSrcFSW | read-only | current | This object indicates the forced switching flag. Forced switching, as described in G.781, is used to override the currently selected synchronization source. Th… |
| 1.3.6.1.4.1.9.9.761.1.1.3.1.19 | ColumncnsInpSrcMSW | read-only | current | This object indicates the manual switching flag. The 'true' value indicates the currently selected clock source is a result of the manual switching. The switch… |
| 1.3.6.1.4.1.9.9.761.1.1.4 | TablecnsExtOutputTable | not-accessible | current | T4 external output table. This table contains a list of T4 external outputs. Each T4 external output is associated with clock source(s) to be found in cnsT4Clo… |
| 1.3.6.1.4.1.9.9.761.1.1.4.1 | RowcnsExtOutputEntry | not-accessible | current | An entry is created in the table when a user adds a T4 external output in the configuration. A T4 external output configured input clock sources are defined in… |
| 1.3.6.1.4.1.9.9.761.1.1.4.1.1 | ColumncnsExtOutListIndex | not-accessible | current | An index that uniquely represents an entry in this table. This index is assigned arbitrarily by the clock selection process and may not be persistent across re… |
| 1.3.6.1.4.1.9.9.761.1.1.4.1.2 | ColumncnsExtOutSelNetsyncIndex | read-only | current | An index that uniquely represents the selected input clock source whose information is reported by a row in cnsT4ClockSourceTable. The index lists the value of… |
| 1.3.6.1.4.1.9.9.761.1.1.4.1.3 | ColumncnsExtOutName | read-only | current | This object indicates the name of a T4 external output. |
| 1.3.6.1.4.1.9.9.761.1.1.4.1.4 | ColumncnsExtOutIntfType | read-only | current | This object indicates the interface type of the T4 external output. |
| 1.3.6.1.4.1.9.9.761.1.1.4.1.5 | ColumncnsExtOutQualityLevel | read-only | current | This object indicates the clock quality of the T4 external output. |
| 1.3.6.1.4.1.9.9.761.1.1.4.1.6 | ColumncnsExtOutPriority | read-only | current | This object indicates the priority of the selected clock source for a T4 external output. A smaller value represents a higher priority. |
| 1.3.6.1.4.1.9.9.761.1.1.4.1.7 | ColumncnsExtOutFSW | read-only | current | This object indicates the forced switching flag. Forced switching, as described in G.781, is used to override the currently selected synchronization source, Th… |
| 1.3.6.1.4.1.9.9.761.1.1.4.1.8 | ColumncnsExtOutMSW | read-only | current | This object indicates the manual switching flag. The 'true' value indicates the currently selected T4 clock source is a result of the manual switch command. Th… |
| 1.3.6.1.4.1.9.9.761.1.1.4.1.9 | ColumncnsExtOutSquelch | read-only | current | This object indicates whether or not a T4 external output is squelched. Squelching is a sychronization function defined to prevent transmission of a timing sig… |
| 1.3.6.1.4.1.9.9.761.1.1.5 | TablecnsT4ClockSourceTable | not-accessible | current | T4 clock source table. This table contains a list of input sources for a specific T4 external output. An entry shall be added to cnsExtOutputTable first. Then … |
| 1.3.6.1.4.1.9.9.761.1.1.5.1 | RowcnsT4ClockSourceEntry | not-accessible | current | An entry is created in the table when a user adds a clock source to a T4 external output in the configuration. The T4 external output is defined in the T4 exte… |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.1 | ColumncnsT4ClkSrcNetsyncIndex | not-accessible | current | An index that uniquely represents an entry in this table. This index is assigned arbitrarily by the clock selection process and may not be persistent across re… |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.2 | ColumncnsT4ClkSrcName | read-only | current | This object indicates the name of a input clock source configured for the T4 clock selection. |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.3 | ColumncnsT4ClkSrcIntfType | read-only | current | This object indicates the type of an input clock source configured for the T4 clock selection. |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.4 | ColumncnsT4ClkSrcPriority | read-only | current | This object indicates the priority of an input clock source configured for the T4 clock selection. A smaller value represents a higher priority. |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.5 | ColumncnsT4ClkSrcESMCCap | read-only | current | This object indicates the ESMC capability of an input clock source configured for the T4 clock selection. This is applicable only to Synchronous Ethernet input… |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.6 | ColumncnsT4ClkSrcSSMCap | read-only | current | This object indicates the SSM capability of an input clock source configured for the T4 clock selection. This is applicable only to any synchronous interface c… |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.7 | ColumncnsT4ClkSrcQualityLevelTxCfg | read-only | current | This object indicates the configured transmit clock quality level of a T4 input clock source. |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.8 | ColumncnsT4ClkSrcQualityLevelRxCfg | read-only | current | This object indicates the configured receive clock quality level of a T4 input clock source. |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.9 | ColumncnsT4ClkSrcQualityLevelTx | read-only | current | This object indicates the most recent clock quality level transmitted on the T4 input clock source. |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.10 | ColumncnsT4ClkSrcQualityLevelRx | read-only | current | This object indicates the last clock quality level received on the T4 input clock source. |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.11 | ColumncnsT4ClkSrcQualityLevel | read-only | current | This object indicates the current clock quality level of the T4 input clock source. This is the effective quality which is derived from three values: 1) most r… |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.12 | ColumncnsT4ClkSrcHoldoffTime | read-only | current | This object indicates the hold-off time value of a T4 input clock source. The hold-off time prevents short activation of signal failure is passed to the select… |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.13 | ColumncnsT4ClkSrcWtrTime | read-only | current | This object indicates the wait-to-restore time value of a T4 input clock source. The wait-to-restore time ensures that a previous failed synchronization source… |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.14 | ColumncnsT4ClkSrcLockout | read-only | current | This object indicates whether or not the lockout command has been applied on a T4 clock source. The 'true' value means the clock source is not considered by th… |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.15 | ColumncnsT4ClkSrcSignalFailure | read-only | current | This object indicates whether or not a signal failure event is currently being reported on the T4 input clock source. |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.16 | ColumncnsT4ClkSrcAlarm | read-only | current | This object indicates whether or not an alarm event is currently being reported on the T4 input clock source. |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.17 | ColumncnsT4ClkSrcAlarmInfo | read-only | current | This object indicates the alarm reasons of a T4 input clock source if an alarm event is being reported on the clock source. |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.18 | ColumncnsT4ClkSrcFSW | read-only | current | This object indicates the forced switching flag. Forced switching, as described in G.781, is used to override the currently selected synchronization source. Th… |
| 1.3.6.1.4.1.9.9.761.1.1.5.1.19 | ColumncnsT4ClkSrcMSW | read-only | current | This object indicates the manual switching flag. The 'true' value indicates the currently selected T4 clock source is a result of the manual switching. The swi… |
| 1.3.6.1.4.1.9.9.761.1.2 | NodecnsNotifObjects | |||
| 1.3.6.1.4.1.9.9.761.1.2.1 | ScalarcnsInpSrcFailClear | accessible-for-notify | current | This object indicates the clear status of a signal failure event. A value of 'true' means a signal failure event reported on a clock source has been cleared. A… |
| 1.3.6.1.4.1.9.9.761.1.2.2 | ScalarcnsInpSrcAlarmClear | accessible-for-notify | current | This object indicates the clear status of an alarm event. A value of 'true' means an alarm event reported on a clock source has been cleared. A value of 'false… |
| 1.3.6.1.4.1.9.9.761.1.3 | NodeciscoNetsyncMIBNotifControl | |||
| 1.3.6.1.4.1.9.9.761.1.3.1 | ScalarcnsMIBEnableStatusNotification | read-write | current | A control object to enable/disable ciscoNetsyncSelectedT0Clock, ciscoNetsyncSelectedT4Clock, ciscoNetsyncInputSignalFailureStatus, ciscoNetsyncInputAlarmStatus… |
| 1.3.6.1.4.1.9.9.761.2 | NodeciscoNetsyncMIBConform | |||
| 1.3.6.1.4.1.9.9.761.2.1 | NodeciscoNetsyncMIBCompliances | |||
| 1.3.6.1.4.1.9.9.761.2.1.1 | ComplianceciscoNetsyncMIBCompliance | current | This is a default module-compliance containing default object groups. | |
| 1.3.6.1.4.1.9.9.761.2.2 | NodeciscoNetsyncMIBGroups | |||
| 1.3.6.1.4.1.9.9.761.2.2.1 | GroupcnsClkSelGlobalObjectGroup | current | This group contains all objects referenced by the G.781 clock selection process table. | |
| 1.3.6.1.4.1.9.9.761.2.2.2 | GroupcnsSelectedInputSourceObjectGroup | current | This group contains all objects referenced by cnsSelectedInputSourceTable. | |
| 1.3.6.1.4.1.9.9.761.2.2.3 | GroupcnsInputSourceObjectGroup | current | This group contains all objects referenced by cnsInputSourceTable. | |
| 1.3.6.1.4.1.9.9.761.2.2.4 | GroupcnsExtOutputObjectGroup | current | This group contains all objects referenced by cnsExtOutputTable. | |
| 1.3.6.1.4.1.9.9.761.2.2.5 | GroupcnsT4ClkSrcObjectGroup | current | This group contains all objects referenced by cnsT4ClockSourceTable. | |
| 1.3.6.1.4.1.9.9.761.2.2.6 | GroupcnsMIBNotifEnablesGroup | current | The collection of objects which are used to enable notification. | |
| 1.3.6.1.4.1.9.9.761.2.2.7 | GroupciscoNetsyncMIBNotificationGroup | current | The is the netsync notification group. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CiscoNetsyncAlarmInfo | BITS { netsyncSrcAlarmReasonAIS(0), netsyncSrcAlarmReasonOOR(1), netsyncSrcAlarmReasonOIR(2), netsyncSrcAlarmReasonInternal(3) } | current | Input clock source's alarm reasons: netsyncSrcAlarmReasonAIS - Alarm Indication Signal netsyncSrcAlarmReasonOOR - Out of range netsyncSrcAlarmReasonOIR - Online Insertion Removal netsyncSrcAlarmReasonInternal - Internal |
| CiscoNetsyncClockMode | INTEGER { netsyncClockModeUnknown(1), netsyncClockModeFreerun(2), netsyncClockModeHoldover(3), netsyncClockModeLocked(4) } | current | Clock operating mode: netsyncClockModeUnknown - system is unable to determine the operating mode. netsyncClockModeFreerun - free-running mode. netsyncClockModeHoldover - holdover mode. netsyncClockModeLocked - a valid c… |
| CiscoNetsyncEECOption | INTEGER { netsyncEECOptionUnknown(1), netsyncEECOption1(2), netsyncEECOption2(3), netsyncEECOptionInvalid(4) } | current | Network synchronization EEC (Ethernet Equipment Clock) options. The EEC options are for Synchronous Ethernet devices and define the requirements for clocks, e.g. bandwidth, frequency accuracy, holdover and noise generat… |
| CiscoNetsyncESMCCap | INTEGER { netsyncESMCCapNone(1), netsyncESMCCapTxRx(2), netsyncESMCCapTx(3), netsyncESMCCapRx(4), netsyncESMCCapInvalid(5) } | current | Network synchronization clock source interface ESMC (Ethernet Synchronization Messaging Channel) capability. ESMC Capability Capability information ====================== ====================== netsyncESMCCapNone No ESM… |
| CiscoNetsyncIfType | INTEGER { netsyncIfTypeUnknown(1), netsyncIfTypeInternal(2), netsyncIfTypeEthernet(3), netsyncIfTypeSonet(4), netsyncIfTypeTop(5), netsyncIfTypeExt(6), netsyncIfTypeController(7), netsyncIfTypeGps(8), netsyncIfTypeAtm(9) } | current | Network synchronization clock source Interface type. Netsync interface Interface type ======================== ============== netsyncIfTypeUnknown Unknown netsyncIfTypeInternal Internal netsyncIfTypeEthernet Ethernet ne… |
| CiscoNetsyncNetworkOption | INTEGER { netsyncNetworkOptionUnknown(1), netsyncNetworkOption1(2), netsyncNetworkOption2Gen1(3), netsyncNetworkOption2Gen2(4), netsyncNetworkOption3(5), netsyncNetworkOptionInvalid(6) } | current | Network synchronization networking options. Network option Network option type =========================== =================== netsyncNetworkOptionUnknown Unknown network option netsyncNetworkOption1 Option I netsyncNet… |
| CiscoNetsyncQLMode | INTEGER { netsyncQLModeUnknown(1), netsyncQLModeQlDisabled(2), netsyncQLModeQlEnabled(3) } | current | The clock mode of the network synchronization clock selection process as described in ITU-T standard G.781 section 5.12. G.781 clock selection runs in one of two clock modes: QL (Quality Level) enabled mode and QL disab… |
| CiscoNetsyncQualityLevel | INTEGER { netsyncQualityLevelNULL(1), netsyncQualityLevelDNU(2), netsyncQualityLevelDUS(3), netsyncQualityLevelFAILED(4), netsyncQualityLevelINV0(5), netsyncQualityLevelINV1(6), netsyncQualityLevelINV2(7), netsyncQualityLevelINV3(8), netsyncQualityLevelINV4(9), netsyncQualityLevelINV5(10), netsyncQualityLevelINV6(11), netsyncQualityLevelINV7(12), netsyncQualityLevelINV8(13), netsyncQualityLevelINV9(14), netsyncQualityLevelINV10(15), netsyncQualityLevelINV11(16), netsyncQualityLevelINV12(17), netsyncQualityLevelINV13(18), netsyncQualityLevelINV14(19), netsyncQualityLevelINV15(20), netsyncQualityLevelNSUPP(21), netsyncQualityLevelPRC(22), netsyncQualityLevelPROV(23), netsyncQualityLevelPRS(24), netsyncQualityLevelSEC(25), netsyncQualityLevelSMC(26), netsyncQualityLevelSSUA(27), netsyncQualityLevelSSUB(28), netsyncQualityLevelST2(29), netsyncQualityLevelST3(30), netsyncQualityLevelST3E(31), netsyncQualityLevelST4(32), netsyncQualityLevelSTU(33), netsyncQualityLevelTNC(34), netsyncQualityLevelUNC(35), netsyncQualityLevelUNK(36) } | current | Clock source QL (quality level) is defined in ITU-T G.781 section 5.4 to reflect the synchronization quality within a network Option, i.e. I, II, and III. The following clock source quality levels are defined for the sy… |
| CiscoNetsyncSSMCap | INTEGER { netsyncSSMCapNone(1), netsyncSSMCapTxRx(2), netsyncSSMCapTx(3), netsyncSSMCapRx(4), netsyncSSMCapInvalid(5) } | current | Network synchronization clock source interface SSM (Synchronization Status Message) capability. SSM Capability Capability information ===================== ====================== netsyncSSMCapNone No SSM capability nets… |