CISCO-OPTICAL-MIB
189 objects
This MIB module defines the managed objects for physical layer characteristics of optical interfaces and performance statistics objects for protocol specific counters in optical devices. Performance monitoring (PM) parameters are used by service providers to gather, store, set thresholds for and report performance data for early detection of problems. Thresholds are used to set error levels for each PM parameter. During the accumulation cycle, if the current value of a performance monitoring parameter reaches or exceeds its corresponding threshold value, a threshold crossing alarm (TCA) is generated. The TCAs provide early detection of performance degradation. Glossary: LBC : Laser Bias Current TX : Transmit RX : Receive PMD : Polarization Mode Dispersion OSNR : Optical Signal to Noise Ratio DGD : Differential Group Delay CD : Chromatic Dispersion rad/s : radian per second dB : decibel dBm : decibel-milliwatt ps : picosecond nm : nanometer.
Imported Objects
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifIndex ifName |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString MacAddress TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.828 | IdentityciscoOpticalMIB | This MIB module defines the managed objects for physical layer characteristics of optical interfaces and performance statistics objects for protocol specific c… | ||
| 1.3.6.1.4.1.9.9.828.0 | NodeciscoOpticalMIBNotifs | |||
| 1.3.6.1.4.1.9.9.828.0.1 | NotificationcoiOpticsStatusChange | current | This notification is generated whenever the defect status of Optics on an interface changes. Varbind 'ifIndex' indicates the interface whose defect status of t… | |
| 1.3.6.1.4.1.9.9.828.0.2 | NotificationcoiOpticalEquipmentAlarm | current | This notification is generated whenever the optical equipment alarm is generated. Varbind 'coiOpticalAlarmLocation' indicates the location on which equipment f… | |
| 1.3.6.1.4.1.9.9.828.1 | NodeciscoOpticalMIBObjects | |||
| 1.3.6.1.4.1.9.9.828.1.1 | NodecoiOpticalController | |||
| 1.3.6.1.4.1.9.9.828.1.1.1 | ScalarcoiOpticalNotifEnabled | read-write | current | This object controls the generation of coiOpticsStatusChange notification. If the value of this object is 'true', then the generation of coiOpticsStatusChange … |
| 1.3.6.1.4.1.9.9.828.1.1.2 | TablecoiOpticalControllerTable | not-accessible | current | This table provides management information for optical layer related attributes of interfaces with an ifType of opticalChannel(195). |
| 1.3.6.1.4.1.9.9.828.1.1.2.1 | RowcoiOpticalControllerEntry | not-accessible | current | An entry containing management information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the fea… |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.1 | ColumncoiOpticalControllerWavelength | read-write | current | This object is used to configure the wavelength on optical channel interfaces in 1/100 nm. |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.2 | ColumncoiOpticalControllerLaserStatus | read-only | current | This object gives the current operational state of the Laser. Valid values are - 'up' - The laser is operational. 'down' - The laser is not operational. |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.3 | ColumncoiOpticalControllerFrequency | read-write | current | This object is used to configure the frequency on optical channel interfaces in 100 MHz. |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.4 | ColumncoiOpticalControllerChannelNumber | read-write | current | This object is used to configure the channel number on optical channel interfaces. Channel Number is set to 0 if not 50GHz grid. |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.5 | ColumncoiOpticalControllerTransmitPower | read-write | current | This object is used to configure the Transmit Power in 1/100 dBm on optical channel interfaces. |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.6 | ColumncoiOpticalControllerOpticsType | read-only | current | This object gives the description of optics present on optical channel interfaces. |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.7 | ColumncoiOpticalControllerRXLowThreshold | read-write | current | This object is used to configure the Receive Low Threshold in 1/100 dBm on optical channel interfaces. |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.8 | ColumncoiOpticalControllerTXLowThreshold | read-write | current | This object is used to configure the Transmit Low Threshold in 1/100 dBm on optical channel interfaces. |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.9 | ColumncoiOpticalControllerRXHighThreshold | read-write | current | This object is used to configure the Receive High Threshold in 1/100 dBm on optical channel interfaces. |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.10 | ColumncoiOpticalControllerTXHighThreshold | read-write | current | This object is used to configure the Transmit High Threshold in 1/100 dBm on optical channel interfaces. |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.11 | ColumncoiOpticalControllerLBCHighThreshold | read-write | current | This object is used to configure the Laser Bias Current High Threshold in 1/10% on optical channel interfaces. |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.12 | ColumncoiOpticalControllerStatus | read-only | current | This object indicates the current defect status of the Optics layer. noDefect(0): No Defect. This bit is set high when no defect is detected on the optics. imp… |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.13 | ColumncoiOpticalControllerPortType | read-only | current | This object gives the port type of the optical interface. |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.14 | ColumncoiOpticalControllerTotalRXPower | read-write | current | This object is used to configure the total receive power in 1/100 dBm on optical channel interfaces. |
| 1.3.6.1.4.1.9.9.828.1.1.2.1.15 | ColumncoiOpticalControllerTotalTXPower | read-write | current | This object is used to configure the total transmit power in 1/100 dBm on optical channel interfaces. |
| 1.3.6.1.4.1.9.9.828.1.1.3 | TablecoiOpticalControllerPerLaneTable | not-accessible | current | This table provides the management information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) and lane number as coiO… |
| 1.3.6.1.4.1.9.9.828.1.1.3.1 | RowcoiOpticalControllerPerLaneEntry | not-accessible | current | An entry containing management information on optical layer related attributes of interfaces with an ifType opticalChannel(195) and lane number as coiOpticalCo… |
| 1.3.6.1.4.1.9.9.828.1.1.3.1.1 | ColumncoiOpticalControllerLane | not-accessible | current | This object specifies the lane number for the optical controller. Each optical controller is divided into data lanes, with each lane operating at some data rat… |
| 1.3.6.1.4.1.9.9.828.1.1.3.1.2 | ColumncoiOpticalControllerPerLaneRXPower | read-only | current | This object specifies the Receive power in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.828.1.1.3.1.3 | ColumncoiOpticalControllerPerLaneTXPower | read-only | current | This object specifies the Transmit power in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.828.1.1.3.1.4 | ColumncoiOpticalControllerPerLaneLBC | read-only | current | This object specifies the Laser Bias Current in 1/10%. |
| 1.3.6.1.4.1.9.9.828.1.1.3.1.5 | ColumncoiOpticalControllerPerLaneOSNR | read-only | current | This object specifies the Optical Signal to Noise Ratio in 1/100 dB. |
| 1.3.6.1.4.1.9.9.828.1.1.3.1.6 | ColumncoiOpticalControllerPerLaneChromaticDispersion | read-only | current | This object specifies the measure of spread of light pulse in ps/nm. |
| 1.3.6.1.4.1.9.9.828.1.1.3.1.7 | ColumncoiOpticalControllerPerLaneDifferentialGroupDelay | read-only | current | This object specifies the propagation time difference between eigenmodes X and Y in 1/100 ps. |
| 1.3.6.1.4.1.9.9.828.1.1.3.1.8 | ColumncoiOpticalControllerPerLaneSecondOrderPMD | read-only | current | This object specifies the threshold Second Order Polarization Mode Dispersion in 1/100 ps^2. |
| 1.3.6.1.4.1.9.9.828.1.1.3.1.9 | ColumncoiOpticalControllerPerLanePolarizationDependentLoss | read-only | current | This object specifies the threshold Polarization Dependent Loss in 1/100 dB. |
| 1.3.6.1.4.1.9.9.828.1.1.3.1.10 | ColumncoiOpticalControllerPerLanePolarizationChangeRate | read-only | current | This object specifies the Polarization Change Rate in 1/100 rad/s. |
| 1.3.6.1.4.1.9.9.828.1.1.3.1.11 | ColumncoiOpticalControllerPerLanePhaseNoise | read-only | current | This object specifies the Fluctuations in the Phase of a Waveform in 1/1000 dB. |
| 1.3.6.1.4.1.9.9.828.1.2 | NodecoiOpticalPerformanceMonitoring | |||
| 1.3.6.1.4.1.9.9.828.1.2.1 | TablecoiOpticalThresholdTable | not-accessible | current | This table provides threshold information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) and Interval type as coiOptT… |
| 1.3.6.1.4.1.9.9.828.1.2.1.1 | RowcoiOpticalThresholdEntry | not-accessible | current | An entry containing threshold information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feat… |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.1 | ColumncoiOptThreshIntervalType | not-accessible | current | This object gives the interval type during which the performance statistics are accumulated for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.2 | ColumncoiOptThreshTXPowerMin | read-write | current | This object is used to configure the threshold of minimum Transmit power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.3 | ColumncoiOptThreshRXPowerMin | read-write | current | This object is used to configure the threshold of minimum Receive power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.4 | ColumncoiOptThreshOSNRMin | read-write | current | This object is used to configure the threshold of minimum Optical Signal to Noise Ratio for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.5 | ColumncoiOptThreshChromaticDispersionMin | read-write | current | This object is used to configure the threshold of minimum measure of spread of light pulse for the interface in ps/nm. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.6 | ColumncoiOptThreshDifferentialGroupDelayMin | read-write | current | This object is used to configure the threshold of minimum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.7 | ColumncoiOptThreshSecondOrderPMDMin | read-write | current | This object is used to configure the threshold of minimum Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.8 | ColumncoiOptThreshPolarizationDependentLossMin | read-write | current | This object is used to configure the threshold of minimum Polarization Dependent Loss for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.9 | ColumncoiOptThreshPolarizationChangeRateMin | read-write | current | This object is used to configure the threshold of minimum Polarization Change Rate for the interface in 1/100 rad/s. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.10 | ColumncoiOptThreshPhaseNoiseMin | read-write | current | This object is used to configure the threshold of minimum Fluctuations in the Phase of a Waveform for the interface in 1/1000 dB. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.11 | ColumncoiOptThreshLBCMin | read-write | current | This object is used to configure the threshold of minumum Laser Bias Current in 1/10%. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.12 | ColumncoiOptThreshTXPowerMax | read-write | current | This object is used to configure the threshold of maximum Transmit power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.13 | ColumncoiOptThreshRXPowerMax | read-write | current | This object is used to configure the threshold of maximum Receive power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.14 | ColumncoiOptThreshOSNRMax | read-write | current | This object is used to configure the threshold of maximum Optical Signal to Noise Ratio for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.15 | ColumncoiOptThreshChromaticDispersionMax | read-write | current | This object is used to configure the threshold of maximum measure of spread of light pulse for the interface in ps/nm. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.16 | ColumncoiOptThreshDifferentialGroupDelayMax | read-write | current | This object is used to configure the threshold of maximum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.17 | ColumncoiOptThreshSecondOrderPMDMax | read-write | current | This object is used to configure the threshold of maximum Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.18 | ColumncoiOptThreshPolarizationDependentLossMax | read-write | current | This object is used to configure the threshold of maximum Polarization Dependent Loss for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.19 | ColumncoiOptThreshPolarizationChangeRateMax | read-write | current | This object is used to configure the threshold of maximum Polarization Change Rate in 1/100 rad/s for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.20 | ColumncoiOptThreshPhaseNoiseMax | read-write | current | This object is used to configure the threshold of maximum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.21 | ColumncoiOptThreshLBCMax | read-write | current | This object is used to configure the threshold of maximum Laser Bias Current in 1/10 % for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.22 | ColumncoiOptThreshTXPowerEnableMin | read-write | current | This object is used to configure the enablement of threshold min Transmit power for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.23 | ColumncoiOptThreshRXPowerEnableMin | read-write | current | This object is used to configure the enablement of the threshold min Receive power for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.24 | ColumncoiOptThreshOSNREnableMin | read-write | current | This object is used to configure the enablement of the threshold min Optical Signal to Noise Ratio for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.25 | ColumncoiOptThreshChromaticDispersionEnableMin | read-write | current | This object is used to configure the enablement of the threshold min measure of spread of light pulse for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.26 | ColumncoiOptThreshDifferentialGroupDelayEnableMin | read-write | current | This object is used to configure the enablement of the threshold min propagation time difference between eigenmodes X and Y for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.27 | ColumncoiOptThreshSecondOrderPMDEnableMin | read-write | current | This object is used to configure the enablement of the threshold min Second Order Polarization Mode Dispersion for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.28 | ColumncoiOptThreshPolarizationDependentLossEnableMin | read-write | current | This object is used to configure the enablement of the threshold min Polarization Dependent Loss for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.29 | ColumncoiOptThreshPolarizationChangeRateEnableMin | read-write | current | This object is used to configure the enablement of the threshold min Polarization Change Rate for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.30 | ColumncoiOptThreshPhaseNoiseEnableMin | read-write | current | This object is used to configure the enablement of the threshold min Fluctuations in the Phase of a Waveform for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.31 | ColumncoiOptThreshLBCEnableMin | read-write | current | This object is used to configure the enablement of the threshold min Laser Bias Current for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.32 | ColumncoiOptThreshTXPowerEnableMax | read-write | current | This object is used to configure the enablement of the threshold max Transmit power for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.33 | ColumncoiOptThreshRXPowerEnableMax | read-write | current | This object is used to configure the enablement of the threshold max Receive power for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.34 | ColumncoiOptThreshOSNREnableMax | read-write | current | This object is used to configure the enablement of the threshold max Optical Signal to Noise Ratio for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.35 | ColumncoiOptThreshChromaticDispersionEnableMax | read-write | current | This object is used to configure the enablement of the threshold max measure of spread of light pulse for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.36 | ColumncoiOptThreshDifferentialGroupDelayEnableMax | read-write | current | This object is used to configure the enablement of the threshold max propagation time difference between eigenmodes X and Y for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.37 | ColumncoiOptThreshSecondOrderPMDEnableMax | read-write | current | This object is used to configure the enablement of the threshold max Second Order Polarization Mode Dispersion for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.38 | ColumncoiOptThreshPolarizationDependentLossEnableMax | read-write | current | This object is used to configure the enablement of the threshold max Polarization Dependent Loss for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.39 | ColumncoiOptThreshPolarizationChangeRateEnableMax | read-write | current | This object is used to configure the enablement of the threshold max Polarization Change Rate for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.40 | ColumncoiOptThreshPhaseNoiseEnableMax | read-write | current | This object is used to configure the enablement of the threshold max Fluctuations in the Phase of a Waveform for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.1.1.41 | ColumncoiOptThreshLBCEnableMax | read-write | current | This object is used to configure the enablement of the threshold max Laser Bias Current for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.2 | TablecoiOpticalCurrentTable | not-accessible | current | This table provides current information for optical layer related attributes of interfaces with an ifType of opticalChannel(195), Lane as coiOptCurrentLane and… |
| 1.3.6.1.4.1.9.9.828.1.2.2.1 | RowcoiOpticalCurrentEntry | not-accessible | current | An entry containing current information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the featur… |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.1 | ColumncoiOptCurrentLane | not-accessible | current | This object specifies the lane number for the optical interface. Each optical controller is divided into data lanes with each lane operating at some data rate,… |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.2 | ColumncoiOptCurrentIntervalType | not-accessible | current | This object gives the interval type during which the current performance statistics are accumulated. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.3 | ColumncoiOptCurrentTXPowerMax | read-only | current | This object specifies the current max Transmit power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.4 | ColumncoiOptCurrentRXPowerMax | read-only | current | This object specifies the current max Receive power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.5 | ColumncoiOptCurrentOSNRMax | read-only | current | This object specifies the current max Optical Signal to Noise Ratio for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.6 | ColumncoiOptCurrentChromaticDispersionMax | read-only | current | This object specifies the current max measure of spread of light pulse for the interface in ps/nm. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.7 | ColumncoiOptCurrentDifferentialGroupDelayMax | read-only | current | This object specifies the current max propagation time difference between eigenmodes X and Y for the interface in 1/100 ps. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.8 | ColumncoiOptCurrentSecondOrderPMDMax | read-only | current | This object specifies the current max Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.9 | ColumncoiOptCurrentPolarizationDependentLossMax | read-only | current | This object specifies the current max Polarization Dependent Loss for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.10 | ColumncoiOptCurrentPolarizationChangeRateMax | read-only | current | This object specifies the current max Polarization Change Rate for the interface in 1/100 rad/s. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.11 | ColumncoiOptCurrentPhaseNoiseMax | read-only | current | This object specifies the current max Fluctuations in the Phase of a Waveform for the interface in 1/1000 dB. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.12 | ColumncoiOptCurrentLBCMax | read-only | current | This object specifies the current max Laser Bias Current in 1/10% for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.13 | ColumncoiOptCurrentTXPowerMin | read-only | current | This object specifies the current min Transmit power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.14 | ColumncoiOptCurrentRXPowerMin | read-only | current | This object specifies the current min Receive power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.15 | ColumncoiOptCurrentOSNRMin | read-only | current | This object specifies the current min Optical Signal to Noise Ratio for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.16 | ColumncoiOptCurrentChromaticDispersionMin | read-only | current | This object specifies the current min measure of spread of light pulse for the interface in ps/nm. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.17 | ColumncoiOptCurrentDifferentialGroupDelayMin | read-only | current | This object specifies the current min propagation time difference between eigenmodes X and Y for the interface in 1/100 ps. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.18 | ColumncoiOptCurrentSecondOrderPMDMin | read-only | current | This object specifies the current min Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.19 | ColumncoiOptCurrentPolarizationDependentLossMin | read-only | current | This object specifies the current min Polarization Dependent Loss for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.20 | ColumncoiOptCurrentPolarizationChangeRateMin | read-only | current | This object specifies the current min Polarization Change Rate for the interface in 1/100 rad/s. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.21 | ColumncoiOptCurrentPhaseNoiseMin | read-only | current | This object specifies the current min Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.22 | ColumncoiOptCurrentLBCMin | read-only | current | This object specifies the current min Laser Bias Current in 1/10% for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.23 | ColumncoiOptCurrentTXPowerAvg | read-only | current | This object specifies the current average Transmit power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.24 | ColumncoiOptCurrentRXPowerAvg | read-only | current | This object specifies the current average Receive power for the interface in 1/100 dBm. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.25 | ColumncoiOptCurrentOSNRAvg | read-only | current | This object specifies the current average Optical Signal to Noise Ratio for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.26 | ColumncoiOptCurrentChromaticDispersionAvg | read-only | current | This object specifies the current average measure of spread of light pulse for the interface in ps/nm. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.27 | ColumncoiOptCurrentDifferentialGroupDelayAvg | read-only | current | This object specifies the current average propagation time difference between eigenmodes X and Y for the interface in 1/100 ps. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.28 | ColumncoiOptCurrentSecondOrderPMDAvg | read-only | current | This object specifies the current average Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.29 | ColumncoiOptCurrentPolarizationDependentLossAvg | read-only | current | This object specifies the current average Polarization Dependent Loss for the interface in 1/100 dB. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.30 | ColumncoiOptCurrentPolarizationChangeRateAvg | read-only | current | This object specifies the current average Polarization Change Rate for the interface in 1/100 rad/s. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.31 | ColumncoiOptCurrentPhaseNoiseAvg | read-only | current | This object specifies the current average Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.32 | ColumncoiOptCurrentLBCAvg | read-only | current | This object specifies the current average Laser Bias Current in 1/10% for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.2.1.33 | ColumncoiOptCurrentTimestamp | read-only | current | This object specifies the timestamp for the current bucket for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3 | TablecoiOpticalIntervalTable | not-accessible | current | This table provides interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(195), lane as coiOptIntervalLane, … |
| 1.3.6.1.4.1.9.9.828.1.2.3.1 | RowcoiOpticalIntervalEntry | not-accessible | current | An entry containing interval information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the featu… |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.1 | ColumncoiOptIntervalLane | not-accessible | current | This object specifies the lane number for the optical interface. Each optical controller is divided into data lanes with each lane operating at some data rate,… |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.2 | ColumncoiOptIntervalIntervalType | not-accessible | current | This object gives the interval type during which the performance statistics are accumulated. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.3 | ColumncoiOptIntervalNum | not-accessible | current | This object identifies the interval for which the set of interval performance values is available. The interval identified by 1 is the most recent 15 minute or… |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.4 | ColumncoiOptIntervalTXPowerMax | read-only | current | This object specifies the interval maximum Transmit power in 1/100 dBm for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.5 | ColumncoiOptIntervalRXPowerMax | read-only | current | This object specifies the interval maximum Receive power in 1/100 dBm for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.6 | ColumncoiOptIntervalOSNRMax | read-only | current | This object specifies the interval maximum Optical Signal to Noise Ratio in 1/100 dB for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.7 | ColumncoiOptIntervalChromaticDispersionMax | read-only | current | This object specifies the interval maximum measure of spread of light pulse for the interface in ps/nm. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.8 | ColumncoiOptIntervalDifferentialGroupDelayMax | read-only | current | This object specifies the interval maximum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.9 | ColumncoiOptIntervalSecondOrderPMDMax | read-only | current | This object specifies the interval maximum Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.10 | ColumncoiOptIntervalPolarizationDependentLossMax | read-only | current | This object specifies the interval maximum Polarization Dependent Loss in 1/100 dB for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.11 | ColumncoiOptIntervalPolarizationChangeRateMax | read-only | current | This object specifies the interval maximum Polarization Change Rate in 1/100 rad/s for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.12 | ColumncoiOptIntervalPhaseNoiseMax | read-only | current | This object specifies the interval maximum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.13 | ColumncoiOptIntervalLBCMax | read-only | current | This object specifies the interval maximum Laser Bias Current in 1/10% for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.14 | ColumncoiOptIntervalTXPowerMin | read-only | current | This object specifies the interval minimum Transmit power in 1/100 dBm for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.15 | ColumncoiOptIntervalRXPowerMin | read-only | current | This object specifies the interval minimum Receive power in 1/100 dBm for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.16 | ColumncoiOptIntervalOSNRMin | read-only | current | This object specifies the interval minimum Optical Signal to Noise Ratio in 1/100 dB for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.17 | ColumncoiOptIntervalChromaticDispersionMin | read-only | current | This object specifies the interval minimum measure of spread of light pulse in ps/nm for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.18 | ColumncoiOptIntervalDifferentialGroupDelayMin | read-only | current | This object specifies the interval minimum propagation time difference between eigenmodes X and Y in 1/100 ps for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.19 | ColumncoiOptIntervalSecondOrderPMDMin | read-only | current | This object specifies the interval minimum Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.20 | ColumncoiOptIntervalPolarizationDependentLossMin | read-only | current | This object specifies the interval minimum Polarization Dependent Loss in 1/100 dB for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.21 | ColumncoiOptIntervalPolarizationChangeRateMin | read-only | current | This object specifies the interval minimum Polarization Change Rate in 1/100 rad/s for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.22 | ColumncoiOptIntervalPhaseNoiseMin | read-only | current | This object specifies the interval minimum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.23 | ColumncoiOptIntervalLBCMin | read-only | current | This object specifies the interval minimum Laser Bias Current in 1/10% for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.24 | ColumncoiOptIntervalTXPowerAvg | read-only | current | This object specifies the interval average Transmit power in 1/100 dBm for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.25 | ColumncoiOptIntervalRXPowerAvg | read-only | current | This object specifies the interval average Receive power in 1/100 dBm for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.26 | ColumncoiOptIntervalOSNRAvg | read-only | current | This object specifies the interval average Optical Signal to Noise Ratio in 1/100 dB for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.27 | ColumncoiOptIntervalChromaticDispersionAvg | read-only | current | This object specifies the interval average measure of spread of light pulse in ps/nm for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.28 | ColumncoiOptIntervalDifferentialGroupDelayAvg | read-only | current | This object specifies the interval average propagation time difference between eigenmodes X and Y in 1/100 ps for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.29 | ColumncoiOptIntervalSecondOrderPMDAvg | read-only | current | This object specifies the interval average Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.30 | ColumncoiOptIntervalPolarizationDependentLossAvg | read-only | current | This object specifies the interval average Polarization Dependent Loss in 1/100 dB for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.31 | ColumncoiOptIntervalPolarizationChangeRateAvg | read-only | current | This object specifies the interval average Polarization Change Rate in 1/100 rad/s for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.32 | ColumncoiOptIntervalPhaseNoiseAvg | read-only | current | This object specifies the interval average Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.33 | ColumncoiOptIntervalLBCAvg | read-only | current | This object specifies the interval average Laser Bias Current in 1/10 % for the interface. |
| 1.3.6.1.4.1.9.9.828.1.2.3.1.34 | ColumncoiOptIntervalTimestamp | read-only | current | This object specifies the timestamp, for the bucket specified by 'coiOptIntervalNum', for the interface. |
| 1.3.6.1.4.1.9.9.828.1.3 | TablecoiOpticalClientInfoTable | not-accessible | current | This table provides management information for optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6).This parameter is ap… |
| 1.3.6.1.4.1.9.9.828.1.3.1 | RowcoiOpticalClientInfoEntry | not-accessible | current | An entry containing information for optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6). Entries are created by the fea… |
| 1.3.6.1.4.1.9.9.828.1.3.1.1 | ColumncoiOpticalClientEthernetNeighbourMAC | read-only | current | This object gives the neighbour MAC Address to which the interface is connected. |
| 1.3.6.1.4.1.9.9.828.1.4 | NodecoiOpticalEquipmentAlarmGroup | |||
| 1.3.6.1.4.1.9.9.828.1.4.1 | ScalarcoiOpticalAlarmLocation | accessible-for-notify | current | This object indicates the location of the component that raised alarm, within the device. |
| 1.3.6.1.4.1.9.9.828.1.4.2 | ScalarcoiOpticalAlarmType | accessible-for-notify | current | This object indicates the type of alarm that is raised. |
| 1.3.6.1.4.1.9.9.828.1.4.3 | ScalarcoiOpticalAlarmTimeStamp | accessible-for-notify | current | This object gives the time when an event occurred. This is accurate only upto a second. |
| 1.3.6.1.4.1.9.9.828.1.4.4 | ScalarcoiOpticalAlarmName | accessible-for-notify | current | This variable gives the user-visible name, which uniquely identifies the alarm in the system. |
| 1.3.6.1.4.1.9.9.828.1.4.5 | ScalarcoiOpticalAlarmAdditionalInfo | accessible-for-notify | current | This variable provides additional info about the alarm. This object would be a null string if no additional information is specified. |
| 1.3.6.1.4.1.9.9.828.1.4.6 | ScalarcoiOpticalAlarmSeverity | accessible-for-notify | current | This variable specifies alarm severity. |
| 1.3.6.1.4.1.9.9.828.1.4.7 | ScalarcoiOpticalAlarmStatus | accessible-for-notify | current | This variable specifies alarm status. |
| 1.3.6.1.4.1.9.9.828.1.4.8 | ScalarcoiOpticalAlarmServiceAffecting | accessible-for-notify | current | This variable specifies the service affecting state of the alarm. |
| 1.3.6.1.4.1.9.9.828.2 | NodeciscoOpticalMIBConformance | |||
| 1.3.6.1.4.1.9.9.828.2.1 | NodeciscoOpticalMIBCompliances | |||
| 1.3.6.1.4.1.9.9.828.2.1.1 | ComplianceciscoOpticalMIBCompliance | deprecated | The compliance statement for platforms that monitor the parameters for the optical interfaces. | |
| 1.3.6.1.4.1.9.9.828.2.1.2 | ComplianceciscoOpticalMIBComplianceRev1 | current | The compliance statement for platforms that monitor the parameters for the optical interfaces. | |
| 1.3.6.1.4.1.9.9.828.2.2 | NodeciscoOpticalMIBGroups | |||
| 1.3.6.1.4.1.9.9.828.2.2.1 | GroupcoiOpticalGroup | current | The collection of objects to give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195). | |
| 1.3.6.1.4.1.9.9.828.2.2.2 | GroupcoiOpticalControllerGroup | current | The collection of objects to allow configurations and give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195… | |
| 1.3.6.1.4.1.9.9.828.2.2.3 | GroupcoiOpticalControllerPerLaneGroup | current | The collection of objects to give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195) and lane number as coiO… | |
| 1.3.6.1.4.1.9.9.828.2.2.4 | GroupcoiOpticalClientInfoGroup | current | The collection of objects to give information related to optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6). | |
| 1.3.6.1.4.1.9.9.828.2.2.5 | GroupcoiOpticalThresholdGroup | current | The collection of objects used for monitoring the threshold information for optical layer related attributes of interfaces with an ifType of opticalChannel(195… | |
| 1.3.6.1.4.1.9.9.828.2.2.6 | GroupcoiOpticalCurrentGroup | current | The collection of objects used for monitoring the current information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) … | |
| 1.3.6.1.4.1.9.9.828.2.2.7 | GroupcoiOpticalIntervalGroup | current | The collection of objects used for monitoring the interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(195)… | |
| 1.3.6.1.4.1.9.9.828.2.2.8 | GroupcoiOpticalNotifEnableGroup | current | The collection of objects to enable the notification generations upon an interface's defect status change on optics layer. | |
| 1.3.6.1.4.1.9.9.828.2.2.9 | GroupcoiOpticalNotifStatusObjectGroup | current | The object to be included in an Optical interface's defect status change notification. | |
| 1.3.6.1.4.1.9.9.828.2.2.10 | GroupcoiOpticalNotifGroup | current | The optical status change notifications whenever the defect status of optical layer on an interface changes. | |
| 1.3.6.1.4.1.9.9.828.2.2.11 | GroupcoiOpticalEquipmentAlarmInfoGroup | current | The optical equipment notifications whenever the alarm is generated. | |
| 1.3.6.1.4.1.9.9.828.2.2.12 | GroupcoiOpticalPowerGroup | current | The collection of objects used for monitoring the total power information for optical layer related attributes of interfaces with an ifType of opticalChannel(1… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CoiIntervalType | INTEGER { fifteenMin(1), oneDay(2), thirtySecond(3) } | current | This value indicates the time period over which performance monitoring data has been collected. Valid values are - fifteenMin(1) - values for the 15 min interval. oneDay(2) - values for the 1 Day interval. thirtySecond(… |
| CoiOptAlarmServiceAffecting | INTEGER { serviceAffecting(1), nonServiceAffecting(2) } | current | This will indicate the sevice-affecting state of the alarm. Valid values are - Service affecting(1) - alarm affects service. Non-Service affecting(2)- alarm does not affect service. |
| CoiOptAlarmSeverity | INTEGER { notReported(1), notAlarmed(2), minor(3), major(4), critical(5) } | current | This will indicate the severity of the notification being sent out. Valid values are - notReported(1) - alarm not reported. notAlarmed(2) - alarm not raised. minor(3) - minor alarm. major(4) - major alarm. critical(5) -… |
| CoiOptAlarmStatus | INTEGER { raised(1), cleared(2), transient(3) } | current | This will indicate the status of the alarm. Valid values are - raised(1) - alarm in raised state. cleared(2) - alarm in cleared state. transient(3)- alarm in transient state. |
| CoiOptAlarmType | INTEGER { alarmUnknown(1), equipmentFailure(2) } | current | This value indicates the alarm type. alarmUnknown(1) - denotes unknown alarm type. equipmentFailure(2) - denotes equipment fail alarm type. |
| CoiOpticalPower | Integer32 (-4000..3000) | current | This value indicates the optical receive or transmit power. |
| CoiOpticalWavelength | Unsigned32 (0 | 1528770..1604030) | current | This value represents the wavelength of optical signals, in an optical interface. It is represented in units of nanometers. A value of zero either indicates that the wavelength is unknown, or that it does not fall under… |
| CoiPortType | INTEGER { clientPort(1), trunkPort(2) } | current | This value indicates the port type of the optical interface. Valid values are - clientPort(1) - denotes client port. trunkPort(2) - denotes trunk port. |