CISCO-OPTICAL-MONITOR-MIB
78 objects
This MIB module defines objects to monitor optical characteristics and set corresponding thresholds on the optical interfaces in a network element.
Imported Objects
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | TEXTUAL-CONVENTION TimeStamp |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.264 | IdentityciscoOpticalMonitorMIB | This MIB module defines objects to monitor optical characteristics and set corresponding thresholds on the optical interfaces in a network element. | ||
| 1.3.6.1.4.1.9.9.264.1 | NodecOpticalMonitorMIBObjects | |||
| 1.3.6.1.4.1.9.9.264.1.1 | NodecOpticalMonGroup | |||
| 1.3.6.1.4.1.9.9.264.1.1.1 | TablecOpticalMonTable | not-accessible | current | This table provides objects to monitor optical parameters in a network element. It also provides objects for setting high and low threshold levels, with config… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1 | RowcOpticalMonEntry | not-accessible | current | An entry in the cOpticalMonTable provides objects to monitor an optical parameter and set threshold levels on that parameter, at an optical interface. Note tha… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.1 | ColumncOpticalMonDirection | not-accessible | current | This object indicates the direction monitored for the optical interface, in this entry. |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.2 | ColumncOpticalMonLocation | not-accessible | current | This object indicates whether the optical characteristics are measured before or after adjustment (e.g. optical amplification or attenuation), at this interfac… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.3 | ColumncOpticalMonParameterType | not-accessible | current | This object specifies the optical parameter that is being monitored in this entry. |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.4 | ColumncOpticalParameterValue | read-only | current | This object gives the value measured for the particular optical parameter specified by the cOpticalMonParameterType object. |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.5 | ColumncOpticalParamHighAlarmThresh | read-write | current | This object is used to set a high alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by cOpticalPar… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.6 | ColumncOpticalParamHighAlarmSev | read-write | current | This object is used to specify a severity level associated with the high alarm threshold given by the cOpticalParamHighAlarmThresh object. The values 'notAlarm… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.7 | ColumncOpticalParamHighWarningThresh | read-write | current | This object is used to set a high warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value giv… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.8 | ColumncOpticalParamHighWarningSev | read-write | current | This object is used to specify a severity level associated with the high warning threshold given by the cOpticalParamHighWarningThresh object. The values 'crit… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.9 | ColumncOpticalParamLowAlarmThresh | read-write | current | This object is used to set a low alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by cOpticalPara… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.10 | ColumncOpticalParamLowAlarmSev | read-write | current | This object is used to specify a severity level associated with the low alarm threshold given by the cOpticalParamLowAlarmThresh object. The values 'notAlarmed… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.11 | ColumncOpticalParamLowWarningThresh | read-write | current | This object is used to set a low warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value give… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.12 | ColumncOpticalParamLowWarningSev | read-write | current | This object is used to specify a severity level associated with the low warning threshold given by the cOpticalParamLowWarningThresh object. The values 'critic… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.13 | ColumncOpticalParamAlarmStatus | read-only | current | This object is used to indicate the current status of the thresholds for the monitored optical parameter on the interface. If a threshold is currently being ex… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.14 | ColumncOpticalParamAlarmCurMaxThresh | read-only | current | This object indicates the threshold value of the highest severity threshold that is currently being exceeded on the interface, for the optical parameter. If no… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.15 | ColumncOpticalParamAlarmCurMaxSev | read-only | current | This object indicates the maximum severity of any thresholds that are currently being exceeded on the interface, for the optical parameter. |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.16 | ColumncOpticalParamAlarmLastChange | read-only | current | This object specifies the value of sysUpTime at the last time a threshold related to a particular optical parameter was exceeded or cleared on the interface. |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.17 | ColumncOpticalMon15MinValidIntervals | read-only | current | This object gives the number of previous 15 minute intervals for which valid performance monitoring data has been stored on the interface. The value of this ob… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.18 | ColumncOpticalMon24HrValidIntervals | read-only | current | This object gives the number of previous 24 hour intervals for which valid performance monitoring data has been stored on the interface. The value of this obje… |
| 1.3.6.1.4.1.9.9.264.1.1.1.1.19 | ColumncOpticalParamThreshSource | read-write | current | This object indicates if the current value of a particular threshold in this entry is user configured value or it is a system default value. It also allows use… |
| 1.3.6.1.4.1.9.9.264.1.1.2 | ScalarcOpticalNotifyEnable | read-write | current | This object specifies the minimum severity threshold governing the generation of cOpticalMonParameterStatus notifications. For example, if the value of this ob… |
| 1.3.6.1.4.1.9.9.264.1.1.3 | ScalarcOpticalMonEnable | read-write | current | This object specifies the types of transceivers for which optical monitoring is enabled. A value of 1 for the bit 'all', specifies that optical monitoring func… |
| 1.3.6.1.4.1.9.9.264.1.1.4 | ScalarcOpticalMonPollInterval | read-write | current | This object specifies the interval in minutes after which optical transceiver data will be polled by system repeatedly and updated in cOpticalMonTable when one… |
| 1.3.6.1.4.1.9.9.264.1.1.5 | TablecOpticalMonIfTable | not-accessible | current | This table contains the list of optical interfaces populated in cOpticalMonTable. |
| 1.3.6.1.4.1.9.9.264.1.1.5.1 | RowcOpticalMonIfEntry | not-accessible | current | An entry containing the information for a particular optical interface. |
| 1.3.6.1.4.1.9.9.264.1.1.5.1.1 | ColumncOpticalMonIfTimeInSlot | read-only | current | This object indicates when this optical transceiver was detected by the system. |
| 1.3.6.1.4.1.9.9.264.1.2 | NodecOpticalPMGroup | |||
| 1.3.6.1.4.1.9.9.264.1.2.1 | TablecOpticalPMCurrentTable | not-accessible | current | This table contains performance monitoring data for the various optical parameters, collected over the current 15 minute or the current 24 hour interval. |
| 1.3.6.1.4.1.9.9.264.1.2.1.1 | RowcOpticalPMCurrentEntry | not-accessible | current | An entry in the cOpticalPMCurrentTable. It contains performance monitoring data for a monitored optical parameter at an interface, collected over the current 1… |
| 1.3.6.1.4.1.9.9.264.1.2.1.1.1 | ColumncOpticalPMCurrentPeriod | not-accessible | current | This object indicates whether the optical parameter values given in this entry are collected over the current 15 minute or the current 24 hour interval. |
| 1.3.6.1.4.1.9.9.264.1.2.1.1.2 | ColumncOpticalPMCurrentDirection | not-accessible | current | This object indicates the direction monitored for the optical interface, in this entry. |
| 1.3.6.1.4.1.9.9.264.1.2.1.1.3 | ColumncOpticalPMCurrentLocation | not-accessible | current | This object indicates whether the optical characteristics are measured before or after adjustment (e.g. optical amplification or attenuation), at this interfac… |
| 1.3.6.1.4.1.9.9.264.1.2.1.1.4 | ColumncOpticalPMCurrentParamType | not-accessible | current | This object specifies the optical parameter that is being monitored, in this entry. |
| 1.3.6.1.4.1.9.9.264.1.2.1.1.5 | ColumncOpticalPMCurrentMaxParam | read-only | current | This object gives the maximum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval. |
| 1.3.6.1.4.1.9.9.264.1.2.1.1.6 | ColumncOpticalPMCurrentMinParam | read-only | current | This object gives the minimum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval. |
| 1.3.6.1.4.1.9.9.264.1.2.1.1.7 | ColumncOpticalPMCurrentMeanParam | read-only | current | This object gives the average value of the monitored optical parameter, in the current 15 minute or the current 24 hour interval. |
| 1.3.6.1.4.1.9.9.264.1.2.1.1.8 | ColumncOpticalPMCurrentUnavailSecs | read-only | current | This object is used to indicate the number of seconds, in the current 15 minute or the current 24 hour interval, for which the optical performance data is not … |
| 1.3.6.1.4.1.9.9.264.1.2.2 | TablecOpticalPMIntervalTable | not-accessible | current | This table stores performance monitoring data for the various optical parameters, collected over previous intervals. This table can have entries for one comple… |
| 1.3.6.1.4.1.9.9.264.1.2.2.1 | RowcOpticalPMIntervalEntry | not-accessible | current | An entry in the cOpticalPMIntervalTable. It contains performance monitoring data for an optical parameter, collected over a previous interval. Note that the se… |
| 1.3.6.1.4.1.9.9.264.1.2.2.1.1 | ColumncOpticalPMIntervalPeriod | not-accessible | current | This object indicates whether the optical parameter values, given in this entry, are collected over a period of 15 minutes or 24 hours. |
| 1.3.6.1.4.1.9.9.264.1.2.2.1.2 | ColumncOpticalPMIntervalNumber | not-accessible | current | A number between 1 and 96, which identifies the interval for which the set of optical parameter values is available. The interval identified by 1 is the most r… |
| 1.3.6.1.4.1.9.9.264.1.2.2.1.3 | ColumncOpticalPMIntervalDirection | not-accessible | current | This object indicates the direction monitored for the optical interface, in this entry. |
| 1.3.6.1.4.1.9.9.264.1.2.2.1.4 | ColumncOpticalPMIntervalLocation | not-accessible | current | This object indicates whether the optical characteristics are measured before or after adjustment (e.g. optical amplification or attenuation), at this interfac… |
| 1.3.6.1.4.1.9.9.264.1.2.2.1.5 | ColumncOpticalPMIntervalParamType | not-accessible | current | This object specifies the optical parameter that is being monitored, in this entry. |
| 1.3.6.1.4.1.9.9.264.1.2.2.1.6 | ColumncOpticalPMIntervalMaxParam | read-only | current | This object gives the maximum value measured for the optical parameter, in a particular 15 minute or 24 hour interval. |
| 1.3.6.1.4.1.9.9.264.1.2.2.1.7 | ColumncOpticalPMIntervalMinParam | read-only | current | This object gives the minimum value measured for the optical parameter, in a particular 15 minute or 24 hour interval. |
| 1.3.6.1.4.1.9.9.264.1.2.2.1.8 | ColumncOpticalPMIntervalMeanParam | read-only | current | This object gives the average value of the measured optical parameter, in a particular 15 minute or 24 hour interval. |
| 1.3.6.1.4.1.9.9.264.1.2.2.1.9 | ColumncOpticalPMIntervalUnavailSecs | read-only | current | This object is used to indicate the number of seconds, in the particular 15 minute or 24 hour interval, for which the optical performance data is not accounted… |
| 1.3.6.1.4.1.9.9.264.2 | NodecOpticalMonitorMIBNotifications | |||
| 1.3.6.1.4.1.9.9.264.2.0 | NodecOpticalMonNotificationPrefix | |||
| 1.3.6.1.4.1.9.9.264.2.0.1 | NotificationcOpticalMonParameterStatus | current | This notification is sent when any threshold related to an optical parameter is exceeded or cleared on an interface. This notification may be suppressed under … | |
| 1.3.6.1.4.1.9.9.264.3 | NodecOpticalMonitorMIBConformance | |||
| 1.3.6.1.4.1.9.9.264.3.1 | NodecOpticalMonitorMIBCompliances | |||
| 1.3.6.1.4.1.9.9.264.3.1.1 | CompliancecOpticalMonitorMIBCompliance | read-only | deprecated | The compliance statement for network elements that monitor optical characteristics and set thresholds on the optical interfaces in a network element. |
| 1.3.6.1.4.1.9.9.264.3.1.2 | CompliancecOpticalMonitorMIBComplianceRev | read-only | current | The compliance statement for network elements that monitor optical characteristics and set thresholds on the optical interfaces in a network element. |
| 1.3.6.1.4.1.9.9.264.3.2 | NodecOpticalMonitorMIBGroups | |||
| 1.3.6.1.4.1.9.9.264.3.2.1 | GroupcOpticalMIBMonGroup | current | A mandatory object that provides monitoring of optical characteristics. | |
| 1.3.6.1.4.1.9.9.264.3.2.2 | GroupcOpticalMIBThresholdGroup | current | A collection of objects that support thresholds on optical parameters and provide status information when the thresholds are exceeded or cleared. | |
| 1.3.6.1.4.1.9.9.264.3.2.3 | GroupcOpticalMIBSeverityGroup | current | A collection of objects that support severities for thresholds on optical parameters. | |
| 1.3.6.1.4.1.9.9.264.3.2.4 | GroupcOpticalMIBPMGroup | current | A collection of objects that provide optical performance monitoring data for 15 minute and 24 hour intervals. | |
| 1.3.6.1.4.1.9.9.264.3.2.5 | GroupcOpticalMIBNotifyEnableGroup | current | An object to control the generation of notifications. | |
| 1.3.6.1.4.1.9.9.264.3.2.6 | GroupcOpticalMIBNotifGroup | current | A notification generated when a threshold on an optical parameter is exceeded or cleared. | |
| 1.3.6.1.4.1.9.9.264.3.2.7 | GroupcOpticalMonIfTimeGroup | current | A collection of object(s) that provide time related information for transceivers in the system. | |
| 1.3.6.1.4.1.9.9.264.3.2.8 | GroupcOpticalMIBEnableConfigGroup | current | A collection of object(s) to enable/disable optical monitoring. | |
| 1.3.6.1.4.1.9.9.264.3.2.9 | GroupcOpticalMIBIntervalConfigGroup | current | A collection of object(s) to specify polling interval for monitoring optical transceivers. | |
| 1.3.6.1.4.1.9.9.264.3.2.10 | GroupcOpticalMonThreshSourceGroup | current | A collection of object(s) to restore a given threshold to its default value. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| OpticalAlarmSeverity | INTEGER { critical(1), major(2), minor(3), notAlarmed(4), notReported(5), cleared(6) } | current | The severity of a trouble condition. A smaller enumerated integer value indicates that the condition is more severe. The severities are defined as follows: 'critical' An alarm used to indicate a severe, service-affectin… |
| OpticalAlarmSeverityOrZero | INTEGER (0..6) | current | A value of either '0' or a valid optical alarm severity. |
| OpticalAlarmStatus | OCTET STRING (SIZE (1)) | current | A bitmap that indicates the current status of thresholds on an interface. The bit is set to 1 if the threshold is currently being exceeded on the interface and will be set to 0 otherwise. (MSB) (LSB) 7 6 5 4 3 2 1 0 + |… |
| OpticalIfDirection | INTEGER { receive(1), transmit(2), notApplicable(3) } | current | This value indicates the direction being monitored at the optical interface. |
| OpticalIfMonLocation | INTEGER { beforeAdjustment(1), afterAdjustment(2), notApplicable(3) } | current | This value applies when there are multiple points at which optical characteristics can be measured, in the given direction, at an interface. It indicates whether the optical characteristics are measured before or after … |
| OpticalParameterType | INTEGER { power(1), acPower(2), ambientTemp(3), laserTemp(4), biasCurrent(5), peltierCurrent(6), xcvrVoltage(7) } | current | This value indicates the optical parameter that is being monitored. Valid values are - power (1) : Optical Power (AC + DC) in 1/10ths of dBm acPower (2) : Optical AC Power in 1/10ths of dBm ambientTemp (3) : Ambient Tem… |
| OpticalParameterValue | Integer32 (-1000000..1000000 ) | current | The value of the optical parameter that is being monitored. The range of values varies depending on the type of optical parameter being monitored, as identified by a corresponding object with syntax OpticalParameterType… |
| OpticalPMPeriod | INTEGER { fifteenMin(1), twentyFourHour(2) } | current | This value indicates the time period over which performance monitoring data has been collected. |