CISCO-OTN-IF-MIB
169 objects
This MIB module defines the managed objects for physical layer characteristics of DWDM optical channel interfaces and performance statistics objects for protocol specific error counters in DWDM optical devices. Performance monitoring (PM) parameters are used by service providers to gather, store, set thresholds for and report performance data for early detection of problems. Thresholds are used to set error levels for each PM parameter. During the accumulation cycle, if the current value of a performance monitoring parameter reaches or exceeds its corresponding threshold value, a threshold crossing alarm (TCA) is generated. The TCAs provide early detection of performance degradation. The definitions contained herein are based on the OTN specifications in ITU-T G.872[ITU-T G.872], G.709 [ITU-T G.709], G.798[ITU-T G.798], G.874[ITU-T G.874], and G.874.1[ITU-T G.874.1]. Glossary: OTN : Optical Transport Network (ITU-T G.709). FEC : Forward Error Correction. PM : Performance Monitor. DWDM : Dense Wavelength Division Multiplexing. FE : Farend or client side of the interface. NE : Nearend or trunk side of the interface. ADM : Add Drop Multiplexer. OCH : Optical Channel. OTS : Optical Transport Section. OMS : Optical Multiplex Section. TCA : Threshold Crossing Alarm. OSC : Optical Supervisory Channel. DCU : Dispersion Compensation Unit. EXP : Express Channel. OSNR : Optical singal to noise ratio. OTU : Optical Channel Transport Unit. ODU : Optical Channel Data Unit.
Imported Objects
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifIndex ifName |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus StorageType TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.639 | IdentityciscoOtnIfMIB | This MIB module defines the managed objects for physical layer characteristics of DWDM optical channel interfaces and performance statistics objects for protoc… | ||
| 1.3.6.1.4.1.9.9.639.0 | NodeciscoOtnIfMIBNotifs | |||
| 1.3.6.1.4.1.9.9.639.0.1 | NotificationcoiOtnIfOTUStatusChange | current | This notification is generated whenever the defect status of OTU layer on an interface changes. Varbind 'ifName' indicates the interface whose defect status of… | |
| 1.3.6.1.4.1.9.9.639.0.2 | NotificationcoiOtnIfODUStatusChange | current | This notification is generated whenever the defect status of ODU layer on an interface changes. Varbind 'ifName' indicates the interface whose defect status of… | |
| 1.3.6.1.4.1.9.9.639.1 | NodeciscoOtnIfMIBObjects | |||
| 1.3.6.1.4.1.9.9.639.1.1 | NodecoiDwdmInterface | |||
| 1.3.6.1.4.1.9.9.639.1.1.1 | TablecoiIfControllerTable | not-accessible | current | This table provides management information for physical layer related attributes of interfaces with an ifType of opticalChannel(195). |
| 1.3.6.1.4.1.9.9.639.1.1.1.1 | RowcoiIfControllerEntry | not-accessible | current | An entry containing management information on physical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the ag… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.1 | ColumncoiIfControllerLoopback | read-write | current | This object is used to configure the loopback mode of the interface. valid values are - 'noLoop' - No Loopback present. 'otherLoop' - A loopback of type other … |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.2 | ColumncoiIfControllerWavelength | read-write | current | This object is used to configure the wavelength of operation on applicable optical channel interfaces. |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.3 | ColumncoiIfControllerLaserAdminStatus | read-write | current | This object is used to configure laser status on applicable interfaces. when it is set to down(2), it results in traffic drop and there should be corresponding… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.4 | ColumncoiIfControllerLaserOperStatus | read-only | current | This object gives the current operational state of the Laser. Valid values are - 'up' - The laser is operational. 'down' - The laser is not operational. if coi… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.5 | ColumncoiIfControllerOtnStatus | read-write | current | This object allows the management client to enable the OTN (ITU-T G.709) framing on applicable interfaces of ifType opticalChannel(195). Valid values are - 'tr… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.6 | ColumncoiIfControllerFECMode | read-write | current | This object allows the management client to enable FEC ( Forward Error Correction ) on applicable interfaces. FEC is a technique that improves digital channel … |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.7 | ColumncoiIfControllerTDCOperMode | read-only | current | This object gives the operational mode of the Tuned Dispersion Compensator (TDC). The values may be - 'auto' - Automatic tuning of dispersion compensation. 'ma… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.8 | ColumncoiIfControllerTDCOperStatus | read-only | current | This object gives the operational status of the Tuned Dispersion Compensator (TDC). The values may be - 'disabled' - TDC has been disabled. 'acquiring' - TDC i… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.9 | ColumncoiIfControllerTDCOperSetting | read-only | current | This object gives the dispersion compensation setting that the TDC has been tuned to. It is expressed in pico-seconds per nanometer. Example: The value of -650… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.10 | ColumncoiIfControllerPreFECBERMantissa | read-only | current | This object gives the mantissa part of the Pre FEC BER or correctable BER at any instance of time. It is represented in one hundreths of a unit.The exponent pa… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.11 | ColumncoiIfControllerPreFECBERExponent | read-only | current | This object gives the exponent part of the Pre FEC BER or correctable BER at any instance of time. It is represented in powers of 10. The mantissa part is defi… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.12 | ColumncoiIfControllerQFactor | read-only | current | This Object gives the value of Q-Factor represented in one hundredths of a dB. Q-Factor represents the analog signal to noise ratio. It suggests the minimum co… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.13 | ColumncoiIfControllerQMargin | read-only | current | Q-Margin defines how much operational system margin that is available for a given circuit. Minimum margin should be defined by one's Network Engineering Group.… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.14 | ColumncoiIfControllerOTNValidIntervals | read-only | current | This object gives the number of contiguous 15 minute intervals for which valid OTN performance monitoring data is available for the particular interface. The a… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.15 | ColumncoiIfControllerFECValidIntervals | read-only | current | This object gives the number of contiguous 15 minute intervals for which valid FEC PM data is available for the particular interface. The actual performance da… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.16 | ColumncoiOtnIfOTUStatus | read-only | current | This object indicates the current defect status of the OTU layer on an OTN interface. noDefect(0): No defect. This bit will be set when none of the following d… |
| 1.3.6.1.4.1.9.9.639.1.1.1.1.17 | ColumncoiOtnIfODUStatus | read-only | current | This object indicates the current defect status of the ODU layer on an OTN interface. noDefect(0): No Defect. This bit will be set when none of the following d… |
| 1.3.6.1.4.1.9.9.639.1.2 | NodecoiDwdmIfOtn | |||
| 1.3.6.1.4.1.9.9.639.1.2.1 | TablecoiOtnNearEndThresholdsTable | not-accessible | current | This table provides objects for configuring OTN ( G.709 ) near end error thresholds on interfaces of ifType opticalChannel (195). |
| 1.3.6.1.4.1.9.9.639.1.2.1.1 | RowcoiOtnNearEndThresholdsEntry | not-accessible | current | An entry containing management information for configuration of performance monitoring thresholds for a given monitor and threshold type. Entries can be create… |
| 1.3.6.1.4.1.9.9.639.1.2.1.1.1 | ColumncoiOtnNearEndThreshIntervalType | not-accessible | current | This object specifies the interval type during which the performance statistics were accumulated. |
| 1.3.6.1.4.1.9.9.639.1.2.1.1.2 | ColumncoiOtnNearEndThreshMonType | not-accessible | current | This object gives the type of performance monitoring for which the threshold is being set. |
| 1.3.6.1.4.1.9.9.639.1.2.1.1.3 | ColumncoiOtnNearEndThresholdType | not-accessible | current | This object gives the type of Error Threshold that is being set. |
| 1.3.6.1.4.1.9.9.639.1.2.1.1.4 | ColumncoiOtnNearEndThreshValue | read-create | current | This object is used to set the near end threshold value for the given threshold type as identified by coiOtnNearEndThresholdType For esr(Error Seconds Ratio), … |
| 1.3.6.1.4.1.9.9.639.1.2.1.1.5 | ColumncoiOtnNearEndThreshStorageType | read-create | current | The storage type for this conceptual row. |
| 1.3.6.1.4.1.9.9.639.1.2.1.1.6 | ColumncoiOtnNearEndThreshStatus | read-create | current | This object controls the creation and deletion of a conceptual row in this table. The value of this object has no effect on whether other objects in this conce… |
| 1.3.6.1.4.1.9.9.639.1.2.2 | TablecoiOtnFarEndThresholdsTable | not-accessible | current | This table provides objects for configuring OTN ( G.709 ) thresholds for far end of interfaces of ifType opticalChannel(195). |
| 1.3.6.1.4.1.9.9.639.1.2.2.1 | RowcoiOtnFarEndThresholdsEntry | not-accessible | current | An entry containing managment information for configuration of far end performance monitoring thresholds for a given monitor and threshold type. Entries can be… |
| 1.3.6.1.4.1.9.9.639.1.2.2.1.1 | ColumncoiOtnFarEndThreshIntervalType | not-accessible | current | This object gives the interval type during which the performance statistics were accumulated in the far end of the interface. |
| 1.3.6.1.4.1.9.9.639.1.2.2.1.2 | ColumncoiOtnFarEndThreshMonType | not-accessible | current | This object gives specify the type of monitoring for which threshold is being set on interfaces in the far end of the interface . |
| 1.3.6.1.4.1.9.9.639.1.2.2.1.3 | ColumncoiOtnFarEndThresholdType | not-accessible | current | This object gives the type of Error Threshold that is being set on far end interfaces of ifType opticalChannel (195). |
| 1.3.6.1.4.1.9.9.639.1.2.2.1.4 | ColumncoiOtnFarEndThreshValue | read-create | current | This object is used to set the far end threshold value for the given threshold type as identified by the index coiOtnFarEndThresholdType.For esr(Error Seconds … |
| 1.3.6.1.4.1.9.9.639.1.2.2.1.5 | ColumncoiOtnFarEndThreshStorageType | read-create | current | The storage type for this conceptual row. |
| 1.3.6.1.4.1.9.9.639.1.2.2.1.6 | ColumncoiOtnFarEndThreshStatus | read-create | current | This object controls the creation and deletion of a conceptual row in this table. The value of this object has no effect on whether other objects in this conce… |
| 1.3.6.1.4.1.9.9.639.1.2.3 | TablecoiOtnNearEndCurrentTable | not-accessible | current | This table contains the cumulative OTN (G.709) PM statistics for the near end of interfaces of ifType opticalChannel(195). The statistics are for the current i… |
| 1.3.6.1.4.1.9.9.639.1.2.3.1 | RowcoiOtnNearEndCurrentEntry | not-accessible | current | An entry containing management information on near end error/statistics counters such as Failure Counts, Errored Seconds...etc in the current interval |
| 1.3.6.1.4.1.9.9.639.1.2.3.1.1 | ColumncoiOtnNearEndCurIntervalType | not-accessible | current | This object gives the interval type during which the near end performance statistics are accumulated. |
| 1.3.6.1.4.1.9.9.639.1.2.3.1.2 | ColumncoiOtnNearEndCurrentMonType | not-accessible | current | This object gives the part of optical network for which the near end OTN performance statistics are being monitored. |
| 1.3.6.1.4.1.9.9.639.1.2.3.1.3 | ColumncoiOtnNearEndCurrentFCs | read-only | current | The counter associated with the number of failures encountered on the near end of interface in the current interval of type coiOtnNearEndCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.2.3.1.4 | ColumncoiOtnNearEndCurrentESs | read-only | current | The counter associated with the number of Errored Seconds encountered on near end of interface in the current interval of type coiOtnNearEndCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.2.3.1.5 | ColumncoiOtnNearEndCurrentSESs | read-only | current | The counter associated with the number of Severely Errored Seconds encountered on the near end of interface in the current interval of type coiOtnNearEndCurInt… |
| 1.3.6.1.4.1.9.9.639.1.2.3.1.6 | ColumncoiOtnNearEndCurrentUASs | read-only | current | The counter associated with the number of Unavailable Seconds encountered on the near end of interface in the current interval of type coiOtnNearEndCurInterval… |
| 1.3.6.1.4.1.9.9.639.1.2.3.1.7 | ColumncoiOtnNearEndCurrentBBEs | read-only | current | The counter associated with the number of Background Block Errors encountered on the near end of interface in the current interval of type coiOtnNearEndCurInte… |
| 1.3.6.1.4.1.9.9.639.1.2.3.1.8 | ColumncoiOtnNearEndCurrentESRs | read-only | current | The counter associated with the Errored Seconds Ratio on the near end of interface in the current interval of type coiOtnNearEndCurIntervalType. Display value … |
| 1.3.6.1.4.1.9.9.639.1.2.3.1.9 | ColumncoiOtnNearEndCurrentSESRs | read-only | current | The counter associated with the Severely Errored Seconds ratio on the near end of interface in current interval of type coiOtnNearEndCurIntervalType. Display v… |
| 1.3.6.1.4.1.9.9.639.1.2.3.1.10 | ColumncoiOtnNearEndCurrentBBERs | read-only | current | The counter associated with the Background Block Errors ratio on the near end of interface in current interval of type coiOtnNearEndCurIntervalType. Display va… |
| 1.3.6.1.4.1.9.9.639.1.2.4 | TablecoiOtnFarEndCurrentTable | not-accessible | current | This table contains the cumulative OTN (G.709) PM stats for the far end of interfaces of ifType opticalChannel(195). The statistics are for the current interva… |
| 1.3.6.1.4.1.9.9.639.1.2.4.1 | RowcoiOtnFarEndCurrentEntry | not-accessible | current | An entry containing managment information on far end error/statistics counters such as Failure Counts, Errored Seconds...etc in the current interval |
| 1.3.6.1.4.1.9.9.639.1.2.4.1.1 | ColumncoiOtnFarEndCurIntervalType | not-accessible | current | This object gives the interval type during which the performance statistics are accumulated in the far end of the interface. |
| 1.3.6.1.4.1.9.9.639.1.2.4.1.2 | ColumncoiOtnFarEndCurrentMonType | not-accessible | current | This object gives the part of optical network for which far end OTN performance statistics are being monitored. |
| 1.3.6.1.4.1.9.9.639.1.2.4.1.3 | ColumncoiOtnFarEndCurrentFCs | read-only | current | The counter associated with the number of failures encountered on far end of interface in current interval of type coiOtnFarEndCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.2.4.1.4 | ColumncoiOtnFarEndCurrentESs | read-only | current | The counter associated with the number of Errored Seconds encountered on far end of interface in current interval of type coiOtnFarEndCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.2.4.1.5 | ColumncoiOtnFarEndCurrentSESs | read-only | current | The counter associated with the number of Severely Errored Seconds encountered on far end of interface in the current interval of type coiOtnFarEndCurIntervalT… |
| 1.3.6.1.4.1.9.9.639.1.2.4.1.6 | ColumncoiOtnFarEndCurrentUASs | read-only | current | The counter associated with the number of Unavailable Seconds encountered on far end of interface in the current interval of type coiOtnFarEndCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.2.4.1.7 | ColumncoiOtnFarEndCurrentBBEs | read-only | current | The counter associated with the number of Background Block Errors encountered on far end of interface in the current interval of type coiOtnFarEndCurIntervalTy… |
| 1.3.6.1.4.1.9.9.639.1.2.4.1.8 | ColumncoiOtnFarEndCurrentESRs | read-only | current | The counter associated with the Errored Seconds Ratio on far end of interface in the current interval of type coiOtnFarEndCurIntervalType. Display value multip… |
| 1.3.6.1.4.1.9.9.639.1.2.4.1.9 | ColumncoiOtnFarEndCurrentSESRs | read-only | current | The counter associated with the Severely Errored Seconds ratio on far end of interface in the current interval of type coiOtnFarEndCurIntervalType. Display val… |
| 1.3.6.1.4.1.9.9.639.1.2.4.1.10 | ColumncoiOtnFarEndCurrentBBERs | read-only | current | The counter associated with the Background Block Errors ratio on far end of interface in the current interval of type coiOtnFarEndCurIntervalType. Display valu… |
| 1.3.6.1.4.1.9.9.639.1.2.5 | TablecoiOtnNearEndIntervalTable | not-accessible | current | This table contains historical cumulative OTN (G.709) PM stats for the near end of interfaces of ifType opticalChannel(195), for the interval type identified b… |
| 1.3.6.1.4.1.9.9.639.1.2.5.1 | RowcoiOtnNearEndIntervalEntry | not-accessible | current | An entry containing management information on near end error/statistics counters such as Failure Counts, Errored Seconds...etc in the given interval. |
| 1.3.6.1.4.1.9.9.639.1.2.5.1.1 | ColumncoiOtnNearEndIntervalType | not-accessible | current | This object gives the interval type during which the performance statistics are accumulated. |
| 1.3.6.1.4.1.9.9.639.1.2.5.1.2 | ColumncoiOtnNearEndIntervalMonType | not-accessible | current | This object gives the part of optical network for which near end OTN performance statistics are being monitored. |
| 1.3.6.1.4.1.9.9.639.1.2.5.1.3 | ColumncoiOtnNearEndIntervalNum | not-accessible | current | This object identifies the interval for which the set of near end OTN performance values is available. The interval identified by 1 is the most recent 15 minut… |
| 1.3.6.1.4.1.9.9.639.1.2.5.1.4 | ColumncoiOtnNearEndIntervalFCs | read-only | current | The counter associated with the number of failures encountered on the near end of interface in the interval identified by coiOtnNearEndIntervalType and coiOtnN… |
| 1.3.6.1.4.1.9.9.639.1.2.5.1.5 | ColumncoiOtnNearEndIntervalESs | read-only | current | The counter associated with the number of Errored Seconds encountered on the near end of interface in the interval identified by coiOtnNearEndIntervalType and … |
| 1.3.6.1.4.1.9.9.639.1.2.5.1.6 | ColumncoiOtnNearEndIntervalSESs | read-only | current | The counter associated with the number of Severely Errored Seconds encountered on the near end of interface in the interval identified by coiOtnNearEndInterval… |
| 1.3.6.1.4.1.9.9.639.1.2.5.1.7 | ColumncoiOtnNearEndIntervalUASs | read-only | current | The counter associated with the number of Unavailable Seconds encountered on the near end of interface in the interval identified by coiOtnNearEndIntervalType … |
| 1.3.6.1.4.1.9.9.639.1.2.5.1.8 | ColumncoiOtnNearEndIntervalBBEs | read-only | current | The counter associated with the number of Background Block Errors encountered on the near end of interface in the interval identified by coiOtnNearEndIntervalT… |
| 1.3.6.1.4.1.9.9.639.1.2.5.1.9 | ColumncoiOtnNearEndIntervalESRs | read-only | current | The counter associated with the Errored Seconds Ratio on the near end of interface in the interval identified by coiiOtnNearEndIntervalType and coiOtnNearEndIn… |
| 1.3.6.1.4.1.9.9.639.1.2.5.1.10 | ColumncoiOtnNearEndIntervalSESRs | read-only | current | The counter associated with the Severely Errored Seconds ratio on the near end of interface in the interval identified by coiOtnNearEndIntervalType and coiOtnN… |
| 1.3.6.1.4.1.9.9.639.1.2.5.1.11 | ColumncoiOtnNearEndIntervalBBERs | read-only | current | The counter associated with the Background Block Errors ratio on the near end of interface in the interval identified by coiOtnNearEndIntervalType and coiOtnNe… |
| 1.3.6.1.4.1.9.9.639.1.2.5.1.12 | ColumncoiOtnNearEndIntervalValidData | read-only | current | This variable indicates if the data for the interval identified by coiOtnNearEndIntervalType and coiOtnNearEndIntervalNum is valid. |
| 1.3.6.1.4.1.9.9.639.1.2.6 | TablecoiOtnFarEndIntervalTable | not-accessible | current | This table contains historical cumulative OTN (G.709) PM stats for the far end interfaces of ifType opticalChannel(195), for the interval type identified by th… |
| 1.3.6.1.4.1.9.9.639.1.2.6.1 | RowcoiOtnFarEndIntervalEntry | not-accessible | current | An entry containing managment information on far end error/statistics counters such as Failure Counts, Errored Seconds...etc in the given interval |
| 1.3.6.1.4.1.9.9.639.1.2.6.1.1 | ColumncoiOtnFarEndIntervalType | not-accessible | current | This object gives the interval type during which the far end performance statistics are accumulated. |
| 1.3.6.1.4.1.9.9.639.1.2.6.1.2 | ColumncoiOtnFarEndIntervalMonType | not-accessible | current | This object gives the part of optical network for which far end OTN performance statistics are being monitored. |
| 1.3.6.1.4.1.9.9.639.1.2.6.1.3 | ColumncoiOtnFarEndIntervalNum | not-accessible | current | This object identifies the interval for which the set of far end OTN performance values for this interface is available. The interval identified by 1 is the mo… |
| 1.3.6.1.4.1.9.9.639.1.2.6.1.4 | ColumncoiOtnFarEndIntervalFCs | read-only | current | The counter associated with the number of Failures encountered on the far end of interface in the interval identified by coiOtnFarEndIntervalType and coiOtnFar… |
| 1.3.6.1.4.1.9.9.639.1.2.6.1.5 | ColumncoiOtnFarEndIntervalESs | read-only | current | The counter associated with the number of Errored Seconds encountered on far end of interface in the interval identified by coiOtnFarEndIntervalType and coiOtn… |
| 1.3.6.1.4.1.9.9.639.1.2.6.1.6 | ColumncoiOtnFarEndIntervalSESs | read-only | current | The counter associated with the number of Severely Errored Seconds encountered on far end interface in the interval identified by coiOtnFarEndIntervalType and … |
| 1.3.6.1.4.1.9.9.639.1.2.6.1.7 | ColumncoiOtnFarEndIntervalUASs | read-only | current | The counter associated with the number of Unavailable Seconds encountered on far end of interface in the interval identified by coiOtnFarEndIntervalType and co… |
| 1.3.6.1.4.1.9.9.639.1.2.6.1.8 | ColumncoiOtnFarEndIntervalBBEs | read-only | current | The counter associated with the number of Background Block Errors encountered on far end of interface in the interval identified by coiOtnFarEndIntervalType an… |
| 1.3.6.1.4.1.9.9.639.1.2.6.1.9 | ColumncoiOtnFarEndIntervalESRs | read-only | current | The counter associated with the Errored Seconds Ratio on far end of interface in the interval identified by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNu… |
| 1.3.6.1.4.1.9.9.639.1.2.6.1.10 | ColumncoiOtnFarEndIntervalSESRs | read-only | current | The counter associated with the Severely Errored Seconds ratio on far end of interface in the interval identified by coiOtnFarEndIntervalType and coiOtnFarEndI… |
| 1.3.6.1.4.1.9.9.639.1.2.6.1.11 | ColumncoiOtnFarEndIntervalBBERs | read-only | current | The counter associated with the Background Block Errors ratio on far end of interface in the interval identified by coiOtnFarEndIntervalType and coiOtnFarEndIn… |
| 1.3.6.1.4.1.9.9.639.1.2.6.1.12 | ColumncoiOtnFarEndIntervalValidData | read-only | current | This variable indicates if the far end data for the interval identified by coiOtnFarEndIntervalType and coiOtnFarEndIntervalNum is valid. |
| 1.3.6.1.4.1.9.9.639.1.2.7 | ScalarcoiOtnIfNotifEnabled | read-write | current | This object controls the generation of coiOtnIfOTUStatusChange and coiOtnIfODUStatusChange notifications. If the value of this object is 'true', then the gener… |
| 1.3.6.1.4.1.9.9.639.1.3 | NodecoiDwdmIfFEC | |||
| 1.3.6.1.4.1.9.9.639.1.3.1 | TablecoiFECThresholdsTable | not-accessible | current | This table contains the configurable thresholds for FEC ( Forward Error Correction ) statistics. |
| 1.3.6.1.4.1.9.9.639.1.3.1.1 | RowcoiFECThresholdsEntry | not-accessible | current | An entry containing management information for configuration of FEC thresholds. Entries can be created for ifIndices with an ifType of opticalChannel(195). Thr… |
| 1.3.6.1.4.1.9.9.639.1.3.1.1.1 | ColumncoiFECThreshIntervalType | not-accessible | current | This object gives the type of the interval for which the thresholds are being set. |
| 1.3.6.1.4.1.9.9.639.1.3.1.1.2 | ColumncoiFECThreshType | not-accessible | current | This object gives the type of the FEC Threshold that is being set. Valid values are - bitErrCor(1) : Bit Errors Corrected byteErrcor(2) : Byte Errors Corrected… |
| 1.3.6.1.4.1.9.9.639.1.3.1.1.3 | ColumncoiFECThreshValue | read-create | current | This object is used for configuring the FEC threshold value for the given threshold type. |
| 1.3.6.1.4.1.9.9.639.1.3.1.1.4 | ColumncoiFECThreshStorageType | read-create | current | The storage type for this conceptual row. |
| 1.3.6.1.4.1.9.9.639.1.3.1.1.5 | ColumncoiFECThreshStatus | read-create | current | This object controls the creation and deletion of a conceptual row in this table.The RowStatus TC requires that this DESCRIPTION clause states under which circ… |
| 1.3.6.1.4.1.9.9.639.1.3.2 | TablecoiFECCurrentTable | not-accessible | current | This table contains the cumulative FEC PM stats for the interfaces of ifType opticalChannel(195) for the current interval of interval type identified coiFECCur… |
| 1.3.6.1.4.1.9.9.639.1.3.2.1 | RowcoiFECCurrentEntry | not-accessible | current | An entry containing managment information on FEC related error/statistics counters such as Bit Errors Corrected, Byte Errors Corrected etc in the current inter… |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.1 | ColumncoiFECCurIntervalType | not-accessible | current | This object gives the interval type during which the FEC PM statistics have been collected. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.2 | ColumncoiFECCurrentCorBitErrs | read-only | current | The counter associated with the number of Bit Errors Corrected on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.3 | ColumncoiFECCurrentCorByteErrs | read-only | current | The counter associated with the number of Byte Errors Corrected on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.4 | ColumncoiFECCurrentDetZeroErrs | read-only | current | The counter associated with the number of zero bit errors detected on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.5 | ColumncoiFECCurrentDetOneErrs | read-only | current | The counter associated with the number of one bit errors detected on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.6 | ColumncoiFECCurrentUncorWords | read-only | current | The counter associated with the number of Uncorrectable Words encountered on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.7 | ColumncoiFECCurrentPreFECMin | read-only | current | The minimum value of PreFEC on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.8 | ColumncoiFECCurrentPreFECMax | read-only | current | The maximum value of PreFEC on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.9 | ColumncoiFECCurrentPreFECAvg | read-only | current | The average value of PreFEC on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.10 | ColumncoiFECCurrentPostFECMin | read-only | current | The minimum value of PostFEC on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.11 | ColumncoiFECCurrentPostFECMax | read-only | current | The maximum value of PostFEC on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.12 | ColumncoiFECCurrentPostFECAvg | read-only | current | The average value of PostFEC on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.13 | ColumncoiFECCurrentQFactorMin | read-only | current | The minimum value of QFactor on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.14 | ColumncoiFECCurrentQFactorMax | read-only | current | The maximum value of QFactor on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.15 | ColumncoiFECCurrentQFactorAvg | read-only | current | The average value of QFactor on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.16 | ColumncoiFECCurrentQMarginMin | read-only | current | The minimum value of QMargin on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.17 | ColumncoiFECCurrentQMarginMax | read-only | current | The maximum value of QMargin on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.2.1.18 | ColumncoiFECCurrentQMarginAvg | read-only | current | The average value of QMargin on this interface in the current interval of type coiFECCurIntervalType. |
| 1.3.6.1.4.1.9.9.639.1.3.3 | TablecoiFECIntervalTable | not-accessible | current | This table contains historical cumulative FEC PM stats for the interfaces of ifType opticalChannel(195), for the interval type identified by the index coiFECIn… |
| 1.3.6.1.4.1.9.9.639.1.3.3.1 | RowcoiFECIntervalEntry | not-accessible | current | An entry containing managment information on FEC error/statistics counters such as Bit Errors Corrected, Byte Errors Corrected etc in the given interval. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.1 | ColumncoiFECIntervalType | not-accessible | current | This object gives the type of interval for which the FEC values have been collected. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.2 | ColumncoiFECIntervalNum | not-accessible | current | This object gives the interval for which the set of FEC PM values are available. The interval identified by 1 is the most recent 15 minute or 24 hour interval,… |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.3 | ColumncoiFECIntervalCorBitErrs | read-only | current | The counter associated with the number of Bit Errors Corrected in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.4 | ColumncoiFECIntervalCorByteErrs | read-only | current | The counter associated with the number of Byte Errors Corrected on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.5 | ColumncoiFECIntervalDetZeroErrs | read-only | current | The counter associated with the number of zero bit errors detected on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.6 | ColumncoiFECIntervalDetOneErrs | read-only | current | The counter associated with the number of one bit errors detected on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.7 | ColumncoiFECIntervalUncorWords | read-only | current | The counter associated with the number of Uncorrectable Words encountered on this interface in the interval identified by coiFECIntervalType and coiFECInterval… |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.8 | ColumncoiFECIntervalValidData | read-only | current | This object indicates whether the data for the interval identified by coiFECIntervalType and coiFECIntervalNum is valid. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.9 | ColumncoiFECIntervalPreFECMin | read-only | current | The minimum value of PreFEC on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.10 | ColumncoiFECIntervalPreFECMax | read-only | current | The maximum value of PreFEC on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.11 | ColumncoiFECIntervalPreFECAvg | read-only | current | The average value of PreFEC on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.12 | ColumncoiFECIntervalPostFECMin | read-only | current | The minimum value of PostFEC on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.13 | ColumncoiFECIntervalPostFECMax | read-only | current | The maximum value of PostFEC on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.14 | ColumncoiFECIntervalPostFECAvg | read-only | current | The average value of PostFEC on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.15 | ColumncoiFECIntervalQFactorMin | read-only | current | The minimum value of QFactor on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.16 | ColumncoiFECIntervalQFactorMax | read-only | current | The maximum value of QFactor on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.17 | ColumncoiFECIntervalQFactorAvg | read-only | current | The average value of QFactor on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.18 | ColumncoiFECIntervalQMarginMin | read-only | current | The minimum value of QMargin on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.19 | ColumncoiFECIntervalQMarginMax | read-only | current | The maximum value of QMargin on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.1.3.3.1.20 | ColumncoiFECIntervalQMarginAvg | read-only | current | The average value of QMargin on this interface in the interval identified by coiFECIntervalType and coiFECIntervalNum. |
| 1.3.6.1.4.1.9.9.639.2 | NodeciscoOtnIfMIBConformance | |||
| 1.3.6.1.4.1.9.9.639.2.1 | NodeciscoOtnIfMIBCompliances | |||
| 1.3.6.1.4.1.9.9.639.2.1.1 | ComplianceciscoOtnIfMIBCompliance | read-only | deprecated | The compliance statement for platforms that monitor the operating status and FEC/OTN with respect to error counters, for the physical layer. |
| 1.3.6.1.4.1.9.9.639.2.1.2 | ComplianceciscoOtnIfMIBCompliance1 | read-only | deprecated | The compliance statement for platforms that monitor the operating status and FEC/OTN with respect to error counters, for the physical layer. |
| 1.3.6.1.4.1.9.9.639.2.1.3 | ComplianceciscoOtnIfMIBCompliance2 | read-only | current | The compliance statement for platforms that monitor the operating status and FEC/OTN with respect to error counters, for the physical layer. |
| 1.3.6.1.4.1.9.9.639.2.2 | NodeciscoOtnIfMIBGroups | |||
| 1.3.6.1.4.1.9.9.639.2.2.1 | GroupcoiIfControllerGroup | current | The collection of objects to allow configurations and give information related to the physical layer characteristics for interfaces of ifType opticalChannel(19… | |
| 1.3.6.1.4.1.9.9.639.2.2.3 | GroupcoiIfOtnNearEndCurrentGroup | current | The collection of objects used for monitoring the near end OTN error counters in the current interval. | |
| 1.3.6.1.4.1.9.9.639.2.2.4 | GroupcoiIfOtnNearEndIntervalGroup | current | The collection of objects used for monitoring the near end OTN error counters in a given interval. | |
| 1.3.6.1.4.1.9.9.639.2.2.5 | GroupcoiIfOtnFarEndCurrentGroup | current | The collection of objects used for monitoring the far end OTN error counters in the current interval. | |
| 1.3.6.1.4.1.9.9.639.2.2.6 | GroupcoiIfOtnFarEndIntervalGroup | current | The collection of objects used for monitoring the far end OTN error counters in a given interval. | |
| 1.3.6.1.4.1.9.9.639.2.2.7 | GroupcoiIfOtnGroup | current | The collection of objects used for monitoring the OTN error counters. | |
| 1.3.6.1.4.1.9.9.639.2.2.8 | GroupcoiIfFECGroup | current | The collection objects used for monitoring the FEC error counters. | |
| 1.3.6.1.4.1.9.9.639.2.2.9 | GroupcoiIfFECCurrentGroup | deprecated | The collection of objects used for monitoring the FEC error counters in the current interval.coiIfFECCurrentGroup object is superseded by coiIfFECCurrentGroup1. | |
| 1.3.6.1.4.1.9.9.639.2.2.10 | GroupcoiIfFECIntervalGroup | deprecated | The collection of objects used for monitoring the FEC error counters in a given interval . coiIfFECIntervalGroup object is superseded by coiIfFECIntervalGroup1. | |
| 1.3.6.1.4.1.9.9.639.2.2.11 | GroupcoiIfOtnNotifEnableGroup | current | The collection of objects to enable the notification generations upon an OTN interface's defect status change on OTU and ODU layer. | |
| 1.3.6.1.4.1.9.9.639.2.2.12 | GroupcoiIfOtnNotifStatusObjectGroup | current | The collection of objects used to monitor the defect status of OTU and ODU layer on an OTN interface. | |
| 1.3.6.1.4.1.9.9.639.2.2.13 | GroupcoiIfOtnNotifGroup | current | The collection of OTN status change notifications whenever the defect status of OTU and ODU layer on an OTN interface changes. | |
| 1.3.6.1.4.1.9.9.639.2.2.14 | GroupcoiIfFECCurrentGroup1 | current | The collection of objects used for monitoring the FEC error counters in the current interval. | |
| 1.3.6.1.4.1.9.9.639.2.2.15 | GroupcoiIfFECIntervalGroup1 | current | The collection of objects used for monitoring the FEC error counters in a given interval . |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| CoiIntervalType | INTEGER { fifteenMin(1), oneDay(2), thirtySecond(3) } | current | This value indicates the time period over which performance monitoring data has been collected. Valid values are - fifteenMin(1) - values for the 15 min interval. oneDay(2) - values for the 1 Day interval. thirtySecond(… |
| CoiMonitorType | INTEGER { path(1), section(2), tcm1(3), tcm2(4) } | current | This value indicates the part of the optical network in which the performance statistics is being monitored. Valid values are - path(1) - Performance statistics for path parameters. section(2) - Performance statistics f… |
| CoiOpticalWavelength | Unsigned32 (0 | 1528770..1604030) | current | This value represents the wavelength of optical signals in a DWDM optical channel. It is represented in units of picometers. A value of zero either indicates that the wavelength is unknown, or that it does not fall unde… |
| CoiOtnThresholdType | INTEGER { fc(1), es(2), ses(3), uas(4), bbe(5), esr(6), sesr(7), bber(8) } | current | This value indicates the type of OTN Error Thresholds that can be defined. Valid values are - fc(1) - Failure Counts. es(2) - Errored Seconds. ses(3) - Severely Errored Seconds. uas(4) - Unavailable Seconds. bbe(5) - Bi… |