CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB
75 objects
This MIB module defines objects required for managing Resilient Ethernet Protocol (REP). Resilient Ethernet Protocol (REP) is a Cisco proprietary protocol that provides an alternative to Spanning Tree Protocol (STP) to control network loops, handle link failures and improve convergence time. REP controls a group of ports connected in a segment; ensures that the segment does not create any bridging loops, and responds to link failures within the segment. The following diagram depicts a REP segment: [Sw E1]E . . [Sw E2]E Sw : Switch. E : Edge port. NE : Non-Edge port. E1/E2: Edge switches. E1 and E2 can either be same or different switches. A REP segment is a chain of ports connected to each other and configured with a segment identifier. Each segment consists of standard (non-edge) segment ports and up to two edge ports. A device can have only two ports that belong to the same segment, and each segment port can have only one external neighbor. One edge port in a REP segment acts as the primary edge port; the other as the secondary edge port. It is the primary edge port that always participates in VLAN load balancing in a REP segment. REP VLAN load balancing is achieved by blocking some VLANs at a configured alternate port and all other VLANs at an edge port. The execution (preemption) of VLAN load balancing is triggered by manually enforcing it or after a pre-defined delay, after the REP segment is complete. When segment is completed, all ports will be in open state except one port that can be in alternate state that is used for VLAN load balancing as explained above.
Imported Objects
| CISCO-SMI | ciscoMgmt |
| CISCO-TC | CiscoVlanList |
| IF-MIB | InterfaceIndex InterfaceIndexOrZero |
| Q-BRIDGE-MIB | VlanId |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | RowStatus TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.9.9.601 | IdentityciscoResilientEthernetProtocolMIB | This MIB module defines objects required for managing Resilient Ethernet Protocol (REP). Resilient Ethernet Protocol (REP) is a Cisco proprietary protocol that… | ||
| 1.3.6.1.4.1.9.9.601.0 | NodeciscoRepMIBNotifs | |||
| 1.3.6.1.4.1.9.9.601.0.1 | NotificationcrepLinkStatus | current | This notification is sent when a REP interface has entered or left REP link operational status. The link is considered operational when 'crepIfOperStatus' is '… | |
| 1.3.6.1.4.1.9.9.601.0.2 | NotificationcrepPreemptionStatus | current | This notification indicates the status of the preemption triggered on REP primary edge. | |
| 1.3.6.1.4.1.9.9.601.0.3 | NotificationcrepPortRoleChange | current | This notification is sent when the role of a Port changes that are indicated by 'crepIfPortRole'. | |
| 1.3.6.1.4.1.9.9.601.1 | NodeciscoRepMIBObjects | |||
| 1.3.6.1.4.1.9.9.601.1.1 | NodecrepGlobalInfo | |||
| 1.3.6.1.4.1.9.9.601.1.1.1 | ScalarcrepVersion | read-only | current | This object indicates the version of REP being used. |
| 1.3.6.1.4.1.9.9.601.1.1.2 | ScalarcrepAdminVlan | read-write | current | The administrative VLAN used by REP to transmit its hardware flooding layer messages. If the VLAN does not already exist, set operation does not create the VLA… |
| 1.3.6.1.4.1.9.9.601.1.1.3 | ScalarcrepNotifsEnable | read-write | current | This object specifies whether the system will generate REP notifications. This object affects the generation of all REP notifications defined in this MIB modul… |
| 1.3.6.1.4.1.9.9.601.1.1.4 | ScalarcrepGlobalRepNotifsRate | read-write | current | This object specifies the maximum rate at which the system will generate notifications defined by this MIB module. If this object value is 0, then the system w… |
| 1.3.6.1.4.1.9.9.601.1.1.5 | ScalarcrepMinSegmentId | read-only | current | This object indicates the minimum segment identifier that can be configured on the device. |
| 1.3.6.1.4.1.9.9.601.1.1.6 | ScalarcrepMaxSegmentId | read-only | current | This object indicates the maximum segment identifier that can be configured on the device. |
| 1.3.6.1.4.1.9.9.601.1.2 | NodecrepInterfaceConfig | |||
| 1.3.6.1.4.1.9.9.601.1.2.1 | TablecrepInterfaceConfigTable | not-accessible | current | This table provides REP configuration for interfaces in the device. This table contains one entry for each interface running REP. |
| 1.3.6.1.4.1.9.9.601.1.2.1.1 | RowcrepInterfaceConfigEntry | not-accessible | current | An entry exists for each interface, if REP is configured on it. On a system that supports REP, all ports with ifType = 'ethernetCsmacd' and those ethernet base… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.1 | ColumncrepIfIndex | not-accessible | current | This object identifies the ifIndex-value assigned to the interface. |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.2 | ColumncrepIfSegmentId | read-create | current | This object specifies the segment that the interface is part. This object can be modified when crepIfConfigRowStatus is 'active'. The valid range is from crepM… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.3 | ColumncrepIfOperStatus | read-only | current | This object indicates the current operational link state of the REP port. If a REP configured interface is down, it will be in 'initDown' state. 'none' - REP i… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.4 | ColumncrepIfPortRole | read-only | current | This object indicates the role or state of a REP port depending on its link status and whether it is forwarding or blocking traffic. 'failedPort' - a port with… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.5 | ColumncrepIfPortID | read-only | current | This object indicates the REP port identifier automatically assigned by REP when enabled. |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.6 | ColumncrepIfAdminEdgePortType | read-create | current | This object specifies the configured edge port type for the interface. |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.7 | ColumncrepIfOperEdgePortType | read-only | current | This object indicates the actual edge port type for the interface. Value 'edge' indicates that the port is secondary edge port. |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.8 | ColumncrepIfPreferredConfig | read-create | current | This object specifies if port should get preference to become the alternate port among other equal ports in the segment. Setting this value to true does not gu… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.9 | ColumncrepifBlockedVlans1k | read-create | current | This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 0 through 1023. If the bit is set to '1', then … |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.10 | ColumncrepifBlockedVlans2k | read-create | current | This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 1024 through 2047. If the bit is set to '1', th… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.11 | ColumncrepifBlockedVlans3k | read-create | current | This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 2048 through 3071. If the bit is set to '1', th… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.12 | ColumncrepifBlockedVlans4k | read-create | current | This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 3072 through 4095. If the bit is set to '1', th… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.13 | ColumncrepLoadBalanceBlockPortType | read-create | current | This object specifies the method defined to identify the alternate port in the segment that takes part in VLAN load balancing by blocking a subset of VLANs aft… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.14 | ColumncrepBlockPortNumInfo | read-create | current | This object specifies the offset of the port in the segment to be blocked for VLAN load balancing. Positive numbers indicate the offset from the primary edge p… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.15 | ColumncrepBlockPortIdInfo | read-create | current | This object specifies the port identifier of the port in the segment to be blocked for VLAN load balancing. 'crepIfPortID' object of the corresponding port pro… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.16 | ColumncrepIfPreemptDelayTimer | read-create | current | This object specifies the interval of time that REP waits before triggering preemption after the segment is complete. The value -1 is used to indicate that no … |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.17 | ColumncrepIfStcnPropagateToSTP | read-create | current | This object specifies if the REP edge propagates the segment topology change notifications to the spanning tree network. This value is only effective on the de… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.18 | ColumncrepIfStcnPropagateToOtherSegs | read-create | current | This object specifies the list of segments to which the REP edge propagates the segment topology change notifications. This value is only effective on the devi… |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.19 | ColumncrepIfStcnPropagateToIf | read-create | current | This object specifies the interface to which the REP edge should propagate the segment topology change notifications. The interface should be of type ifType = … |
| 1.3.6.1.4.1.9.9.601.1.2.1.1.20 | ColumncrepIfConfigRowStatus | read-create | current | This object is used to manage the creation, deletion, and modification of rows in this table. A row may be created using the 'CreateAndGo' option. When the row… |
| 1.3.6.1.4.1.9.9.601.1.2.2 | TablecrepInterfaceStatsTable | not-accessible | current | A table for REP interfaces statistics. This table augments the crepInterfaceConfigTable. |
| 1.3.6.1.4.1.9.9.601.1.2.2.1 | RowcrepInterfaceStatsEntry | not-accessible | current | The counter entries are not persistent. This is because once REP is un-configured on the interface the row would be deleted and hence they will restart if REP … |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.1 | ColumncrepCounterDiscontinuityTime | read-only | current | The value of sysUpTime on the most recent occasion at which REP counters suffered a discontinuity on this interface. If no such discontinuities have occurred s… |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.2 | ColumncrepLslRxPdus | read-only | current | This object indicates the number of link status layer PDUs received on the port. |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.3 | ColumncrepLslTxPdus | read-only | current | This object indicates the number of link status layer PDUs transmitted on the port. |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.4 | ColumncrepHflRxPdus | read-only | current | This object indicates the number of hardware flood layer PDUs received on the port. |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.5 | ColumncrepHflTxPdus | read-only | current | This object indicates the number of hardware flood layer PDUs transmitted on the port. |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.6 | ColumncrepBpaTlvRxPackets | read-only | current | This object indicates the number of blocked port advertisement TLVs received on the port. |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.7 | ColumncrepBpaTlvTxPackets | read-only | current | This object indicates the number of blocked port advertisement TLVs transmitted on the port. |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.8 | ColumncrepBpaStcnLslRxPackets | read-only | current | This object indicates the number of segment topology change notifications received as blocked port advertisement through link status layer. |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.9 | ColumncrepBpaStcnLslTxPackets | read-only | current | This object indicates the number of segment topology change notifications transmitted as blocked port advertisement through link status layer. |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.10 | ColumncrepBpaStcnHflRxPackets | read-only | current | This object indicates the number of segment topology change notifications received as blocked port advertisement through hardware flood layer. |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.11 | ColumncrepBpaStcnHflTxPackets | read-only | current | This object indicates the number of segment topology change notifications transmitted as blocked port advertisement through hardware flood layer. |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.12 | ColumncrepEpaElectionTlvRxPackets | read-only | current | This object indicates the number of end port advertisement election TLVs received that are used for determining the role, namely primary edge or secondary edge. |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.13 | ColumncrepEpaElectionTlvTxPackets | read-only | current | This object indicates the number of end port advertisement election TLVs transmitted that are used for determining the role, namely primary edge or secondary e… |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.14 | ColumncrepEpaCommandTlvRxPackets | read-only | current | This object indicates the number of end port advertisement command TLVs received that are used to authorize a port to takeover the segment for the purpose of V… |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.15 | ColumncrepEpaCommandTlvTxPackets | read-only | current | This object indicates the number of end port advertisement command TLVs transmitted that are used to authorize a port to takeover the segment for the purpose o… |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.16 | ColumncrepEpaInfoTlvRxPackets | read-only | current | This object indicates the number of end port advertisement information TLVs received on the port. These messages are sent by the end ports (configured edge por… |
| 1.3.6.1.4.1.9.9.601.1.2.2.1.17 | ColumncrepEpaInfoTlvTxPackets | read-only | current | This object indicates the number of end port advertisement information TLVs transmitted on the port. These messages are sent by the end ports (configured edge … |
| 1.3.6.1.4.1.9.9.601.1.3 | NodecrepSegmentConfig | |||
| 1.3.6.1.4.1.9.9.601.1.3.1 | TablecrepSegmentTable | not-accessible | current | This table specifies REP segments configured on the device. |
| 1.3.6.1.4.1.9.9.601.1.3.1.1 | RowcrepSegmentEntry | not-accessible | current | A list of REP segment entries. The number of segments configured on the device determines the number of entries. An entry is created when a segment identifier … |
| 1.3.6.1.4.1.9.9.601.1.3.1.1.1 | ColumncrepSegmentId | not-accessible | current | This object identifies the segment identifier. |
| 1.3.6.1.4.1.9.9.601.1.3.1.1.2 | ColumncrepSegmentInterface1 | read-only | current | This object indicates the ifIndex-value assigned to the first interface that is part of the segment. |
| 1.3.6.1.4.1.9.9.601.1.3.1.1.3 | ColumncrepSegmentInterface2 | read-only | current | This object indicates the ifIndex-value assigned to the second interface that is part of the segment. The value of zero means that the InterfaceIndex is not kn… |
| 1.3.6.1.4.1.9.9.601.1.3.1.1.4 | ColumncrepSegmentComplete | read-only | current | This object indicates if the segment is complete such that no port in the segment is in failed state. |
| 1.3.6.1.4.1.9.9.601.1.3.1.1.5 | ColumncrepSegmentPreempt | read-write | current | This object should be set to true by NMS for triggering manual preemption. This may cause a momentary traffic disruption. Though this can be done for any node … |
| 1.3.6.1.4.1.9.9.601.1.3.1.1.6 | ColumncrepSegmentPreemptStatus | read-only | current | This object indicates the status of the last preemption trigger. 'none' - preemption trigger is not executed. 'preemptSuccessful' - preemption action for the p… |
| 1.3.6.1.4.1.9.9.601.2 | NodeciscoRepMIBConform | |||
| 1.3.6.1.4.1.9.9.601.2.1 | NodeciscoRepMIBCompliances | |||
| 1.3.6.1.4.1.9.9.601.2.1.1 | ComplianceciscoRepMIBCompliance | read-only | current | The compliance statement for CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB. |
| 1.3.6.1.4.1.9.9.601.2.2 | NodeciscoRepMIBGroups | |||
| 1.3.6.1.4.1.9.9.601.2.2.1 | GroupciscoRepGlobalGroup | current | A collection of global objects for use with the REP feature. | |
| 1.3.6.1.4.1.9.9.601.2.2.2 | GroupciscoRepInterfaceGroup | current | A collection of interface specific objects for use with the REP feature. | |
| 1.3.6.1.4.1.9.9.601.2.2.3 | GroupciscoRepNotificationGroup | current | A collection of notifications for use with the REP feature. | |
| 1.3.6.1.4.1.9.9.601.2.2.4 | GroupciscoRepSegmentGroup | current | A collection of segment specific objects for use with the REP feature. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| RepPortType | INTEGER { notEdge(1), edge(2), edgePrimary(3), edgeNoNeighbor(4), edgeNoNeighborPrimary(5) } | current | This TC describes the port type of the REP port. 'notEdge' - non-edge Port. 'edge' - edge port for the segment. 'edgePrimary' - primary edge port for the segment. 'edgeNoNeighbor' - no neighbor edge port for the segment… |
| RepSegmentId | Unsigned32 | current | This TC describes an object to provide the unique identifier for the REP segment. |
| RepSegmentList | OCTET STRING | current | This TC describes an object that indicates the list of REP segments. Each octet within this value specifies a set of eight segments. The first octet represents the first 8 segments of the range of segments specified by … |